Modern Forms PD-15604 Acid Mode d'emploi
- Catégorie
- Mur
- Taper
- Mode d'emploi
1Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
INSTALLATION INSTRUCTION
156 - LED Pendant
PD-15604
HARDWARE
A1 B1 C1
Wire Connector
Qty: 3 pcs
Junction Box Screw
Qty: 2 pcs + 1 Extra
Mounting Screw
Qty: 1 Extra
WARNING
IMPORTANT: NEVER attempt any work without shutting o the electricity.
- Read all instructions before installing.
- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.
- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”
the circuit breaker switch(es) that control the power to the xture or room that you are working on.
- Place the wall switch in the “OFF” position.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are
worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les
règlements locaux.
- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt
(« OFF »).
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté
et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du
luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta lación de esta
lámpara.
- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional y las normas locales.
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali mentación
principal en la posición “OFF” (APAGADO).
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni
utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación
ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.
2Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
PREPARATION
1. Shut o the power at the circuit breaker and remove existing
xture, including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on
a clear area. Be careful not to lose any small parts necessary
for installation.
CONNECTING THE WIRES Fig. 2
3. Remove the mounting screw (C1) from the xture.
4. Adjust the xture wire length by pushing the cable gripper on
the canopy and pulling the wire as desired.
5. Connect the driver input wires with junction box wires as
shown in Fig. 2, making sure that all wire connectors (A1)
are secured. If your outlet box has a green or bare copper
ground wire, connect the xture’s ground wire to it.
Otherwise, connect the xture’s ground wire directly to the
mounting plate using the green screw provided. After wires
are connected, tuck them carefully inside the junction box.
*Require Driver to be recessed within the junction box.
MOUNTING THE FIXTURE Fig. 1
6. Secure the mounting plate to the junction box using junction
box screws (B1). The side of the mounting plate marked “GND”
must face out.
7. Place the xture over the mounting plate and secure it with
mounting screws (C1).
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig. 2 Wiring
FIG.1
A1
B1
Wire Connector
Driver (Input)
Supply Wire
Junction Box
Mounting Plate
Junction Box Screw
C1 Mounting
Screw
Canopy
Cable Gripper
Ground Wire Screw
Ground Wire
INSTALLATION INSTRUCTION
156 - LED Pendant
PD-15604
Back Plate Dimensions
4 1/2”
4 1/2”
2 1/2”
-
1
-
2
Modern Forms PD-15604 Acid Mode d'emploi
- Catégorie
- Mur
- Taper
- Mode d'emploi
dans d''autres langues
Documents connexes
-
Modern Forms PD-41803L Cascade Mode d'emploi
-
-
-
-
-
-
-
-
-