INSTALLATION INSTRUCTIONS

HARDWARE

modernforms.com

Phone (800) 526.2588

Fax (800) 526.2585

Headquarters/Eastern Distribution Center

1750 Archibald Avenue

Ontario, CA 91760

Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Nov. 2021

CAUTION: To prevent electrical shock, ensure electricity has been turned o at the circuit breaker before beginning.

• Read all instructions before installing.

• System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.

• When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.

• Retain installation instructions for future maintenance reference.

WARNING: All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or

• Lisez toutes les instructions avant l’installation.

• Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux

règlements locaux.

• Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.

ATTENTION: Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement

avec les pièces et/ou accessoires fournis pour être utilisés avec les produits Modern Forms. Remplacer des pièces ou accessoires non conçus

pour ce produit Modern Forms pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la

garantie. Veuillez contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.

NOTE D’ENTRETIEN: Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons

aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec

Support Column

Qty: 1pc

Allen Screw

Qty: 1pcs+1 Extra

INSTALLATION INSTRUCTIONS

Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Nov. 2021

Phone (800) 526.2588

Fax (800) 526.2585

Headquarters/Eastern Distribution Center

44 Harbor Park Drive

Port Washington, NY 11050

Central Distribution Center

1600 Distribution Ct

Lithia Springs, GA 30122

Western Distribution Center

1750 Archibald Avenue

Ontario, CA 91760

FIG. 3

Fixture Wires

Bare wire

FIG. 2 Wiring

FIG. 1



1. Shut o the power at the circuit breaker and remove existing xture, including the crossbar.

2. Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.



3. Remove the mounting screw (B) and back plate from the xture.

4. The lamp can switch between three color temperatures (2700K-3000K-3500K), which can be adjusted to your preference with the switch in

the canopy (Fig.3).

5. Remove the bottom screw ( C ) and top screw (D), fasten the bottom diuser between the xture and decorative frame using bottom screw

( C ),loose the allen screw (H) using allen wrench (I

6. Drill holes in the wall aligned with the key holes located in the mounting back plate and the decorative frame .

a green or bare copper ground wire, connect the xture’s ground wire to it. Otherwise, connect the xture’s ground wire directly to the back

plate using the GND screw provided. After wires are connected, tuck them carefully inside the junction box.



8. Insert the plastic anchor (F) and ax the support column (G) to the lower plastic anchor(F) using wood screw (E).

9. Secure xture to back plate with mounting screw (B) . Ensure the support column is aligned and inserted into the frame's lower support arm.

10. Place the fabric shade over the xture so it sits on the notch of the xture, secure the top diuser by fastening the top screw (D) .

11. Secure the frame’s lower support arm to the wall so it is ush by tightening the allen screw (H) using allen wrench (I).