Dometic PLB40 Manuel utilisateur

Taper
Manuel utilisateur
PLB40
Portable lithium iron phosphate
battery pack
Operating manual . . . . . . . . . . . . . . . . . . . . .5
Batterie lithium fer phosphate
portable
Notice d’utilisation . . . . . . . . . . . . . . . . . . . 19
Batería de litio-ferrofosfato
portátil
Instrucciones de uso . . . . . . . . . . . . . . . . . .34
EN
FR
ES
POWER & CONTROL
PORTABLE BATTERY PACK
DometicPLB40_OPM_4445102661_AMER3_20xx-xx-xx.book Seite 1 Dienstag, 26. Januar 2021 5:33 17
© 2021 Dometic Group. The visual appearance of the contents of this manual is
protected by copyright and design law. The underlying technical design and the
products contained herein may be protected by design, patent or be patent
pending. The trademarks mentioned in this manual belong to Dometic Sweden AB.
All rights are reserved.
DometicPLB40_OPM_4445102661_AMER3_20xx-xx-xx.book Seite 2 Dienstag, 26. Januar 2021 5:33 17
PLB40
3
1
2
3
4
1
2
13 4 87
6
5 9
10
2
DometicPLB40_OPM_4445102661_AMER3_20xx-xx-xx.book Seite 3 Dienstag, 26. Januar 2021 5:33 17
PLB40
4
!
211111 3 4 5 6
78
9
3
DometicPLB40_OPM_4445102661_AMER3_20xx-xx-xx.book Seite 4 Dienstag, 26. Januar 2021 5:33 17
EN
PLB40 Explanation of symbols
5
Please read these instructions carefully and follow all instructions, guidelines, and warnings included in this product manual in order to ensure
that you install, use, and maintain the product properly at all times. These instructions MUST stay with this product.
By using the product, you hereby confirm that you have read all instructions, guidelines, and warnings carefully and that you understand and
agree to abide by the terms and conditions as set forth herein. You agree to use this product only for the intended purpose and application
and in accordance with the instructions, guidelines, and warnings as set forth in this product manual as well as in accordance with all appli-
cable laws and regulations. A failure to read and follow the instructions and warnings set forth herein may result in an injury to yourself and
others, damage to your product or damage to other property in the vicinity. This product manual, including the instructions, guidelines, and
warnings, and related documentation, may be subject to changes and updates. For up-to-date product information, please visit
documents.dometic.com, dometic.com.
Table of contents
1 Explanation of symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
2 General safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
3 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
4 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
5 Technical description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
6 Using the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
7 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
8 Maintaining and cleaning the product. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
9 Limited warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
10 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
11 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
1 Explanation of symbols
!
!
WARNING!
Safety instruction: Indicates a hazardous situation that, if not avoided,
could result in death or serious injury.
CAUTION!
Safety instruction: Indicates a hazardous situation that, if not avoided,
could result in minor or moderate injury.
DometicPLB40_OPM_4445102661_AMER3_20xx-xx-xx.book Seite 5 Dienstag, 26. Januar 2021 5:33 17
EN
General safety instructions PLB40
6
A
2 General safety instructions
The manufacturer accepts no liability for damage in the following cases:
Damage to the product resulting from mechanical influences and incorrect
connection voltage
Alterations to the product without express permission from the manufacturer
Use for purposes other than those described in the operating manual
The declaration of conformity can be requested from the manufacturer (contact infor-
mation on the back).
Note the following basic safety information when using electrical devices to protect
against:
Electric shock
•Fire hazards
•Injury
2.1 General safety
!WARNING! INSTRUCTIONS PERTAINING TO RISK OF FIRE, ELEC-
TRIC SHOCK, OR INJURY TO PERSONS.
Only use the device as intended.
Disconnect the device from the mains
Before cleaning and maintenance
–After use
Before changing a fuse
To reduce risk of damage to the electric plug and cord, pull the plug
rather than the cord when disconnecting the device.
Do not use a device that is damaged or modified. Damaged or modi-
fied devices may exhibit unpredictable behavior resulting in fire,
explosion or risk of injury.
Do not operate the device with a damaged cord or plug, or a dam-
aged output cable.
NOTICE!
Indicates a situation that, if not avoided, can result in property damage.
DometicPLB40_OPM_4445102661_AMER3_20xx-xx-xx.book Seite 6 Dienstag, 26. Januar 2021 5:33 17
EN
PLB40 General safety instructions
7
Do not disassemble the device, take it to a qualified service person
when service or repair is required. Incorrect reassembly may result in a
risk of fire or electric shock.
To reduce the risk of electric shock, unplug the device from the outlet
before attempting any instructed servicing.
Do not expose to liquid, vapor, rain, sleet, snow or the like.
The device shall be stored indoors and protected from the elements.
Never smoke or allow a spark or flame in vicinity of battery or engine.
When charging the device, work in a well ventilated area and do not
restrict ventilation in any way.
Do not expose the device to fire or excessive temperature. Exposure
to fire or temperature above 13C (26F) may cause explosion.
Electrical devices are not toys.
Always keep and use the device out of the reach of children.
Children must be supervised to ensure that they do not play with the
device.
ANOTICE! MATERIAL DAMAGE.
Do not insert foreign objects into the output or input terminals.
Do not put fingers or hands into the device.
Do not attempt to replace the internal battery cells.
Before using for the first time, charge your battery pack using one of
the methods described in chapter “Charging the lithium iron phos-
phate battery pack” on page 12.
Before using the device for the first time, check that the voltage speci-
fication on the rating plate matches that of the power supply.
Never pull on the power cord to unplug the device from the power
socket.
Store the device in a dry and cool place.
2.2 Operating the device safely
!WARNING! INSTRUCTIONS PERTAINING TO RISK OF FIRE, ELEC-
TRIC SHOCK, OR INJURY TO PERSONS.
Only use the charger supplied to charge the device. Use of an attach-
ment not recommended or sold by the manufacturer may result in a
risk of fire, electric shock, or injury to persons.
DometicPLB40_OPM_4445102661_AMER3_20xx-xx-xx.book Seite 7 Dienstag, 26. Januar 2021 5:33 17
EN
Scope of delivery PLB40
8
The power socket to which the device is connected must be close by
and easily accessible.
!CAUTION! FIRE AND/OR EXPLOSION HAZARD.
•Do not operate the device
In the vicinity of corrosive fumes
In the vicinity of combustible materials
In areas where there is a danger of explosions
•Do not place the device next to heat sources such as fires.
Place the device in a shady place. Avoid direct sun exposure in hot
and humid surroundings for a proper usage.
ANOTICE! MATERIAL DAMAGE.
Do not disconnect any cables when the device is still in use.
Only use the device in upright position.
3Scope of delivery
4 Intended use
The portable lithium iron phosphate battery pack is for use in camping application. It
comes with four outlets to power devices like tablet, mobile phone, portable
fridge/freezer etc.
The battery pack is suitable for
the connection to 12 V appliances with low power consumption e.g. small invert-
ers up to 150 W,
the connection to a laptop with an additional 150 W inverter connected to the
12 V DC connection socket output.
No. in
fig. 1, page 3 Description
1 Portable lithium iron phosphate battery pack
2 DC charge cable
3 AC power supply unit
4 2x DC Fuse
DometicPLB40_OPM_4445102661_AMER3_20xx-xx-xx.book Seite 8 Dienstag, 26. Januar 2021 5:33 17
EN
PLB40 Technical description
9
It is not allowed
to use the battery pack as a starter battery for a vehicle,
to use two battery packs in parallel connection.
This product is only suitable for the intended purpose and application in accordance
with these instructions.
This manual provides information that is necessary for proper installation and/or
operation of the product. Poor installation and/or improper operating or mainte-
nance will result in unsatisfactory performance and a possible failure.
The manufacturer accepts no liability for any injury or damage to the product
resulting from:
Incorrect assembly or connection, including excess voltage
Incorrect maintenance or use of spare parts other than original spare parts
provided by the manufacturer
Alterations to the product without express permission from the manufacturer
Use for purposes other than those described in this manual
Dometic reserves the right to change product appearance and product
specifications.
5 Technical description
The portable lithium iron phosphate battery pack (LiFePO4) enables mobile power
supply for portable refrigeration, USB devices and small inverters up to 150 W con-
tinuous output.
A DC consumer unit (e.g. a portable refrigeration) can be simultaneously supplied
with power while the lithium iron phosphate battery is being charged via the power
supply unit.
The housing is shock, heat and UV resistant.
The lithium iron phosphate battery can be charged in three ways:
via the supplied AC/DC charger on the AC mains (max. 8 A)
via DC connection through vehicle alternator (max. 8 A)
via DC connection through solar panel
The device has the following protective functions:
Overtemperature, undertemperature protection
Overvoltage protection
DometicPLB40_OPM_4445102661_AMER3_20xx-xx-xx.book Seite 9 Dienstag, 26. Januar 2021 5:33 17
EN
Technical description PLB40
10
Undervoltage protection
Overcurrent protection
Short circuit protection
Incorrect polarity protection
5.1 Connections and display
5.2 Display
No. in
fig. 2, page 3 Description
1 Power button
2 Display (LCD)
3 2 x USB socket (5 V, max. 4.2 A overall)
412Vg 2-pin connection output to portable refrigeration
512Vg heavy duty connection socket output for portable
refrigeration and 12 V applicances
6 Adjustable handle
7 2x fuse holder
8 AC/DC adapter input socket
9 DC/DC Anderson™ SB™ input socket
10 Reset button (beneath the cap)
No. in
fig. 3, page 4 Description
1 A failure occurred (chapter “Troubleshooting” on
page 14).
2 See chapter “Troubleshooting” on page 14.
3 See chapter “Troubleshooting” on page 14.
4 The battery pack supplies energy to an USB device.
!
DometicPLB40_OPM_4445102661_AMER3_20xx-xx-xx.book Seite 10 Dienstag, 26. Januar 2021 5:33 17
EN
PLB40 Using the appliance
11
6 Using the appliance
6.1 Before first use
Before first use or storing plug the battery pack into the wall charger until it is fully
charged.
Observe the information given in chapter “Charging the lithium iron phosphate
battery pack” on page 12.
6.2 Starting and switching off
Starting the lithium iron phosphate battery pack
Press the power button (fig. 21, page 3) for at least 3 seconds to start the
device.
The device emits 2 beeps.
5 The battery pack supplies energy to a device connected to
the 2-PIN output.
6 The battery pack supplies energy to a device connected to
the DC output.
7 State of charge as a percentage
8 Battery is being discharged
Battery is being charged
Battery is being charged and discharged at the same time
9 See chapter “Troubleshooting” on page 14.
No. in
fig. 3, page 4 Description
DometicPLB40_OPM_4445102661_AMER3_20xx-xx-xx.book Seite 11 Dienstag, 26. Januar 2021 5:33 17
EN
Using the appliance PLB40
12
The display shows the operational status:
: the lithium iron phosphate battery is being charged
: the lithium iron phosphate battery is being discharged
: the lithium iron phosphate battery is on idle mode
The display switches off automatically after 1 minute.
Switching the display on
Press the power button (fig. 21, page 3) briefly to switch on the display.
Switching off the lithium iron phosphate battery pack
The battery pack switches off automatically after 24 hours if no load and no charger
are connected.
Press the power button (fig. 21, page 3) for at least 3 seconds to switch the
device off.
The device emits 1 beep.
The display switches off.
6.3 Charging the lithium iron phosphate battery pack
!
Place the lithium iron phosphate battery on a firm base.
Charging with the power supply unit
Connect the power supply unit to the connection socket (fig. 28, page 3).
Connect the power supply unit to the AC mains.
The symbol lights up.
The display shows the charging status.
Charging with the smart alternator, 12 V accessory socket or solar panel
Connect the charge cable to the connection socket (fig. 29, page 3).
Connect the DC plug to the DC inlet Anderson socket on battery side.
The symbol lights up the battery state of charge as a percentage.
WARNING! FIRE AND/OR EXPLOSION HAZARD.
Lithium iron phosphate batteries that are charged with too high voltage
can ignite. Use 8 to 25 V input voltage to charge the battery pack.
DometicPLB40_OPM_4445102661_AMER3_20xx-xx-xx.book Seite 12 Dienstag, 26. Januar 2021 5:33 17
EN
PLB40 Using the appliance
13
The display shows the charging status.
If charging the battery pack with a solar panel, observe the following require-
ments:
Use without a solar controller:
Ensure that the solar panel outputs between 8 – 25 V DC and a maximum
charging current of 10 A.
Use with a solar controller:
Ensure the solar charger does not need a counter voltage from the battery
side to start charging. Ensure that the maximum charging current is 10 A
(check with the solar panel manufacturer).
6.4 Checking the charge level
Press the power button (fig. 21, page 3).
The display shows the battery state of charge as a percentage.
The symbol flashes when the battery capacity is below 20 %.
6.5 Connecting consumer devices
fig. 2, page 3
Open the cap for the desired device:
–USB devices (3)
–2-pin 12VDC socket outlet (4)
–12VDC socket (5)
Insert your device’s plug into the corresponding socket.
The symbol and the related output symbol light up.
6.6 Replacing fuses
Ensure that the battery pack is not connected to AC/DC or DC/DC charger.
Disconnect all loads.
Press the power button for at least 3 s to switch the battery pack off.
Undo the fuse holder.
Replace the fuse with a 20 A 3 AG glass-slow acting fuse.
DometicPLB40_OPM_4445102661_AMER3_20xx-xx-xx.book Seite 13 Dienstag, 26. Januar 2021 5:33 17
EN
Troubleshooting PLB40
14
7 Troubleshooting
Problem Cause Remedy
The battery pack does not
start/function when pressing
the power button.
The battery pack has shut
down due to overtempera-
ture (> 65 °C/149 °F).
Connect the AC/DC char-
ger to the battery pack.
If the battery pack does not
start up, press the reset
button and hold it until for a
few seconds.
The battery is defective. Contact a service center.
The display shows the
warning symbol and the
low / high temperature sym-
bol flashes. An error sound is
continuously beeping during
charging.
The ambient temperature for
charging the device is too
low / high.
Stop charging the device.
Turn the device off. Wait until
the ambient temperature
comes to a permitted value
(chapter “Technical data” on
page 17).
The display shows the
warning symbol and the
low / high temperature sym-
bol flashes. The device
beeps for 15 seconds and
then switches off automati-
cally during discharging.
The ambient temperature for
discharging the device is too
low / high.
Stop discharging the device.
Turn the device off. Wait until
the ambient temperature
comes to a permitted value
(chapter “Technical data” on
page 17).
The display shows the warn-
ing symbol and the fuse
blown symbol flashes. An
error sound is continuously
beeping for 30 seconds.
The DC output fuse has
blown. Additionally the DC
symbol flashes in the display.
Turn the device off.
Change the DC fuse (chapter
“Replacing fuses” on
page 13).
The 2-PIN fuse has blown.
Additionally the 2-PIN
symbol flashes in the display.
Turn the device off.
Change the 2-PIN fuse (chap-
ter “Replacing fuses” on
page 13).
An error sound is continu-
ously beeping (above 25 V).
until pulling off the charger or
fault release.
The input voltage of the char-
ger is wrong.
Turn the charger off. Connect
a charger with the standard
charge voltage (chapter
“Technical data” on
page 17).
DometicPLB40_OPM_4445102661_AMER3_20xx-xx-xx.book Seite 14 Dienstag, 26. Januar 2021 5:33 17
EN
PLB40 Troubleshooting
15
The display shows the warn-
ing symbol and the charge
arrow symbol flashes with
audible alarm and stops after
30 seconds (5 –8 V±1).
The input voltage of the char-
ger is wrong.
Turn the charger off. Connect
a charger with the standard
charge voltage (chapter
“Technical data” on
page 17).
No charge arrow is shown
(under 5 V).
The input voltage of the char-
ger is wrong.
Turn the charger off. Connect
a charger with the standard
charge voltage (chapter
“Technical data” on
page 17).
The display shows the warn-
ing symbol. The discharge
arrow and either the USB or
2-pin or DC symbol flashes.
An error sound is beeping for
60 seconds.
Over current protection was
triggered.
Turn the device off. Release
some of the load before
switching the device on
again.
Short circuit protection was
triggered.
Turn the device off. Clear the
short circuit before switching
the device on again.
The battery symbol is flash-
ing. An error sound beeps
every 3 seconds for 10 times.
After the beeps the device
switches off automatically.
The battery capacity is 0 %. Charge the device.
The battery does not give out
current (without active turn-
ing on the device).
The battery does not give out
current until it is charged up
to 10 % (SOC) or activated by
user.
Charge the device.
The letters and symbols on
the display are fading.
The display is overheated. Place the battery pack in a
cool environment.
The display is defective. Contact a service center.
Problem Cause Remedy
DometicPLB40_OPM_4445102661_AMER3_20xx-xx-xx.book Seite 15 Dienstag, 26. Januar 2021 5:33 17
EN
Maintaining and cleaning the product PLB40
16
8 Maintaining and cleaning the product
A
Occasionally clean the product with a damp cloth.
9 Limited warranty
LIMITED WARRANTY AVAILABLE AT
DOMETIC.COM/WARRANTY.
IF YOU HAVE QUESTIONS OR TO OBTAIN A COPY OF THE LIMITED WARRANTY
FREE OF CHARGE, CONTACT THE DOMETIC WARRANTY DEPARTMENT:
DOMETIC CORPORATION
CUSTOMER SUPPORT CENTER
5155 VERDANT DRIVE,
ELKHART, IN 46516
1-800-544-4881
NOTICE! MATERIAL DAMAGE.
Do not use sharp or hard objects or cleaning agents for cleaning as
these may damage the product.
Do not use alcohol based cleaning materials for cleaning the gloss
top cover.
Fully charge the lithium iron phosphate battery at least every six
months. Overloading the battery or storing it for too long without
charging it may cause permanent damage to the battery.
DometicPLB40_OPM_4445102661_AMER3_20xx-xx-xx.book Seite 16 Dienstag, 26. Januar 2021 5:33 17
EN
PLB40 Disposal
17
10 Disposal
Place the packaging material in the appropriate recycling waste bins wherever
possible.
MIf you wish to finally dispose of the product, ask your local recycling centre
or specialist dealer for details about how to do this in accordance with the
applicable disposal regulations.
Protect the environment!
Do not dispose of any batteries with general household waste.
Return defective or used batteries to your retailer or dispose of them at
collection points.
11 Technical data
PLB40
Battery type: Lithium iron phosphate/LiFePO4
Battery rated capacity: 40 Ah
Rated battery voltage: 12.8 Vg
Rated output current (derating of 5 % per
channel / per °C for temperatures above
40 °C (104 °F)):
DC socket: 15 A
2-PIN socket: 15 A
USB socket: 2.4 A per socket, 4.2 A overall
Input voltage range: 8 – 25 Vg
Maximum DC/DC charging current: 8 A
Charging time AC/DC Charger:
(dependent on several factors)
10 % ~ 35 min
0 – 20 % ~ 1 h 10 min
0 – 40 % ~ 2 h 20 min
0 – 60 % ~ 3 h 30 min
0 – 80 % ~ 4 h 40 min
0 – 100 % ~ 6 h 0 min
DometicPLB40_OPM_4445102661_AMER3_20xx-xx-xx.book Seite 17 Dienstag, 26. Januar 2021 5:33 17
EN
Technical data PLB40
18
Power supply unit
Lifecycle: Potential lifecycle at 80 % depth of discharge
(depending on charge cycle and storage
condition)
Up to 2000 charging cycles
Rated input voltage:
Power supply unit / battery:
PWM solar controller:
12 Vg
14.6 Vg
Cut off voltage: 11.2 Vg
Max. self-discharge rate at 25 °C (77 °F): 5 % per month
Ambient temperature for operation: 0 °C to +45 °C (+32 °F to +113 °F)
Dimensions (L x W x H): 197 x 197 x 257 mm (7.76 x 7.76 x 10.12 in)
Weight: 7.54 kg (16.62 lbs)
Inspection/certification:
PLB40
AC Input:
DC output:
100 – 240 Vw/ 50/60 Hz, 2.5 A
12 Vg, 10 A
PLB40
UN 38.3
DometicPLB40_OPM_4445102661_AMER3_20xx-xx-xx.book Seite 18 Dienstag, 26. Januar 2021 5:33 17
FR
PLB40 Explication des symboles
19
Veuillez lire et suivre attentivement l’ensemble des instructions, directives et avertissements figurant dans ce manuel afin de vous assurer que
vous installez, utilisez et entretenez le produit correctement à tout moment. Ces instructions DOIVENT rester avec ce produit.
En utilisant le produit, vous confirmez par la présente que vous avez lu attentivement l’ensemble des instructions, directives et avertissements
et que vous comprenez et acceptez de respecter les modalités et conditions énoncées dans le présent document. Vous acceptez d’utiliser
ce produit uniquement pour l’usage et l’application prévus et conformément aux instructions, directives et avertissements figurant dans le
manuel du produit, ainsi qu’à toutes les lois et réglementations applicables. Si vous ne lisez et ne respectez pas les instructions et les
avertissements figurant dans ce manuel, vous risquez de vous blesser ou de blesser d’autres personnes, d’endommager votre produit ou
d’endommager d’autres biens à proximité. Le présent manuel produit, y compris les instructions, directives et avertissements, ainsi que la
documentation associée peuvent faire l’objet de modifications et de mises à jour. Pour obtenir des informations actualisées sur le produit,
rendez-vous sur documents.dometic.com, dometic.com.
Sommaire
1 Explication des symboles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
2 Consignes générales de sécuri. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3 Contenu de la livraison . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4 Usage conforme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
5 Description technique . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
6 Utilisation de l’appareil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
7 Guide de dépannage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
8 Entretien et nettoyage du produit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
9 Limitation de la Garantie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
10 Mise au rebut. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
11 Caractéristiques techniques . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
1 Explication des symboles
!
!
AVERTISSEMENT !
Consigne de sécurité signalant une situation dangereuse qui peut
entraîner la mort ou de graves blessures si elle n’est pas évitée.
ATTENTION !
Consigne de sécurité signalant une situation dangereuse qui peut
entraîner des blessures de gravité moyenne ou légère si elle n’est pas
évitée.
DometicPLB40_OPM_4445102661_AMER3_20xx-xx-xx.book Seite 19 Dienstag, 26. Januar 2021 5:33 17
FR
Consignes générales de sécurité PLB40
20
A
2 Consignes générales de sécurité
Le fabricant décline toute responsabilité pour des dommages dans les cas suivants :
des sollicitations mécaniques et une tension de raccordement incorrecte ayant
endommagé le matériel
des modifications apportées au produit sans autorisation explicite de la part du
fabricant
une utilisation différente de celle décrite dans la notice
La déclaration de conformité peut être demandée auprès du fabricant (coordonnées
au dos).
Lors de l’utilisation d’appareils électriques, les consignes générales de sécurité sui-
vantes doivent être respectées afin d’éviter :
une décharge électrique,
un incendie,
des blessures.
2.1 Sécurité générale
!AVERTISSEMENT ! INSTRUCTIONS RELATIVES AUX RISQUES
D’INCENDIE, DE CHOC ÉLECTRIQUE OU DE BLESSURES CORPO-
RELLES.
Utilisez l’appareil conformément à l’usage pour lequel il a été conçu.
Débranchez l’appareil du secteur
avant tout nettoyage et entretien
après chaque utilisation
avant le changement d’un fusible
Pour réduire le risque d’endommagement de la fiche et du cordon
électrique, tirez sur la fiche plutôt que sur le cordon lorsque vous
débranchez l’appareil.
AVIS !
Remarque signalant une situation qui peut entraîner des dommages
matériels si elle n’est pas évitée.
DometicPLB40_OPM_4445102661_AMER3_20xx-xx-xx.book Seite 20 Dienstag, 26. Januar 2021 5:33 17
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48

Dometic PLB40 Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues