Synology RT6600ax Guide d'installation

Catégorie
Points d'accès WLAN
Taper
Guide d'installation
Synology Router RT6600ax
Hardware Installation Guide
Table of Contents
Chapter 1: Before You Start
Package Contents
3
Synology RT6600ax at a Glance
4
LED Indicator Table
5
Hardware Specification
6
Safety Instructions
7
Chapter 2: Hardware Setup
Adjust Antennas
8
Position Your RT6600ax
8
Connect to Your RT6600ax
9
Set up Synology Router Manager (SRM)
11
Synology_HIG_RT6600ax_20211208
2
1Chapter
Before You Start
Thank you for purchasing this Synology product! Before setting up your new expansion unit, please check the
package contents to verify that you have received the items below. Also, make sure to read the safety
instructions carefully to avoid harming yourself or damaging your expansion unit.
Note: All images below are for illustrative purposes only, and may differ from the actual product.
Package Contents
Main unit x 1
AC power adapter x 1
RJ-45 LAN cable x 1
3
Synology RT6600ax at a Glance
1
2
3
4
1213
10
8
9 11
No.
Article Name
Location
Description
1
USB 3.0 Port
Connect an external drive, USB printer, or other types of USB
devices here.
2
WAN Port
Connect a network cable from the ISP modem into this port to
establish WAN connection.
1. Connect a network cable from the ISP modem into this port to
3
2.5G WAN/LAN Port
establish WAN connection.
2. Connect network cables into these ports to establish LAN
Rear Panel
connection.
4
LAN Port
Connect network cables into these ports to establish LAN
connection.
5
Power Button
Press to power on/off the Synology Router.
6
RESET Button
Press and hold for four seconds (Soft Reset) or for ten seconds
(Hard Reset).
7
Power Port
Connect the AC power adapter here.
8
LAN Indicator
Displays the status of LAN connection.
9
WAN Indicator
Front Panel
Displays the status of WAN connection.
10
Wi-Fi Indicator
Displays the status of Wi-Fi connection.
11
STATUS Indicator
Displays the status of the system.
12
WPS Button
Right Panel
Press to start WPS.
13
Wi-Fi Button
Press to turn on/off the Wi-Fi network.
4
Chapter 1: Before You Start
LED Indicator Table
LED Indicator
Color
Status
Description
Green
Static
Powered on
Blinking
System Ready
Static
System booting/Rebooting/Hard Reset
Status Indicator
Orange
Blinking
Restoring settings (Soft Reset)/Mesh
network disconnected
Green/Orange
Blinking
Searching device
Off
Powered off
Green
Static
Wi-Fi active
Wi-Fi
Blinking
WPS connecting
Off
No Wi-Fi
Green
Static
Network connected
WAN
Blinking
Data transmitting
Off
Network disconnected
Green
Static
Gigabit/2.5G connection
Blinking
Gigabit/2.5G data transmitting
LAN 1
Orange
Static
10/100 Mbps connection
Blinking
10/100 Mbps data transmitting
Off
No network
Green
Static
Gigabit connection
Blinking
Gigabit data transmitting
LAN 2-4
Orange
Static
10/100 Mbps connection
Blinking
10/100 Mbps data transmitting
Off
No network
5
Chapter 1: Before You Start
Hardware Specification
Item
RT6600ax
External Ports
USB 3.0 x 1
WAN Port
• Gigabit WAN x 1
• Gigabit WAN x 1 and 2.5G WAN x 1 (Dual WAN)
LAN Ports
• Gigabit LAN x 3 and 2.5G LAN x 1
• Gigabit LAN x 3 (Dual WAN)
Size (H x W x D) (mm)
65 x 280 x 180 (without antennas)
Weight (kg)
0.9 kg
Supported Clients
• Windows 7 onwards
(for SRM management)
• Mac OS 10. 12 onwards
File Systems
External: EXT4, EXT3, FAT, NTFS, HFS+
Wireless Standards
• 2.4GHz: 802.11 b/g/n/ax
• 5GHz: 802.11 a/n/ac/ax
• 802.11ax (2.4GHz): Up to 600 Mbps
Operating Frequency Range
• 802.11ax (5GHz-1): Up to 1200 Mbps
• 802.11ax (5GHz-2): Up to 4800 Mbps
Wireless Operation Modes
Wireless Router
• Wireless AP (Access Point)
• 64/128-bit WEP • WPS support
WPA2-Personal • WPA/WPA2-Personal
Wireless Security
WPA2-Enterprise • WPA/WPA2-Enterprise
• Opportunistic Wireless Encryption (OWE)
• WPA3-Personal • WPA3-Enterprise
• WPA2/WPA3-Personal
Antennas
• 2T2R Omni-directional high-gain dipole (2.4GHz/5GHz-1)
• 4T4R Omni-directional high-gain dipole (5GHz-2)
Buttons & Switches
• Power • WPS • Wi-Fi On/Off • Reset
Language Localization
• Line voltage: 100V to 240V AC
• Frequency: 50/60Hz
Environment Requirements
• Operating Temperature: 40 to 104˚F (5 to 40˚C)
• Storage Temperature: -5 to 140˚F (-20 to 60˚C)
• Relative Humidity: 5% to 95% RH
Note: Model specifications are subject to change without notice. Please refer to www.synology.com for the latest information.
6
Chapter 1: Before You Start
Safety Instructions
Keep away from direct sunlight and away from chemicals. Ensure a stable environment
with no abrupt changes in temperature or humidity.
Place the unit right side up at all times.
Keep the unit away from liquids.
Before cleaning, unplug the power cord. Do not use chemical or aerosol cleaners. Wipe
with damp paper towels.
To prevent the unit from falling over, do not place it on carts or any unstable surfaces.
The power cord must plug into the correct supply voltage. Ensure the supplied AC
voltage is correct and stable.
Warning, electric shock hazard. To remove all electrical current from the device,
ensure that all power cords are disconnected from the power source.
Risk of explosion if the battery is replaced by an incorrect type. Dispose of used batteries
appropriately.
Power cord must be plugged into a socket-outlet with earthing connection.
Keep body parts away from moving fan.
This product must be installed by qualified personnel in a restricted access location (like
dedicated equipment rooms, service closets).
7
Chapter 1: Before You Start
2Chapter
Hardware Setup
Adjust Antennas
For optimal Wi-Fi performance, tilt the antennas so that they are at a 90 degree angle to the surface.
Position Your RT6600ax
For optimal performance, it is recommended to position your RT6600ax as advised below:
On a stable surface (e.g. an elevated shelf) away from any possible physical interruptions.
Close to the center of the area where the wired/wireless client devices are placed, and within a visible
distance from the wireless devices.
In a position where few walls and ceilings are between your RT6600ax and its client devices.
Away from any potential electrical signal sources, such as other Wi-Fi routers, 3G/4G bases, and
microwave ovens.
Away from large expanses of metal or other materials, such as metal doors, glass panels, and concrete.
Place Flat on a Surface
Simply place your RT6600ax flat on a horizontal, stable surface.
8
Connect to Your RT6600ax
1 Use the included network cable to connect your RT6600ax (at the WAN1 port) to the ISP modem. Connect
one end of the power adapter to the power port on your RT6600ax, and the other end to the power outlet.
Press the power button to power on your RT6600ax. Wait for up to two minutes until the STATUS and WAN
LED indicators turn green.
2 Connect wireless client devices to your RT6600ax. When the Wi-Fi indicator has turned static green,
RT6600ax is ready to connect with other devices. Use your wireless device to scan and join the Wi-Fi network
created by your RT6600ax.
Note:
The default credentials for the Wi-Fi network:
Wi-Fi SSID: Synology_(Serial)
Password: synology
You can change it during the initial SRM setup.
9
Chapter 2: Hardware Setup
3 Connect wired client devices to your RT6600ax. Use network cables to connect devices to the LAN ports.
The corresponding LAN LED indicators should turn orange/green to indicate successful connection.
10
Chapter 2: Hardware Setup
Set up Synology Router Manager (SRM)
1 Use a computer or wireless device connected to your RT6600ax's local network. If you use a wireless device,
scan and join the Wi-Fi network (SSID: Synology_(Serial); Password: synology).
2 Open a web browser, and enter either URL into the address bar:
http://router.synology.com
http://192.168.1.1:8000
3 Once connected, click Start to launch the SRM Setup Wizard.
4 Fill in the information to set up the administrator account. Click Next to continue.
11
Chapter 2: Hardware Setup
5 Fill in the information to set up the Wi-Fi network. Click Next to continue.
6 Set up the operation mode. When choosing the Wireless Router mode, you can also enable External
access to SRM so that only external access via the HTTP(S) port (e.g. 8000/8001) can reach SRM.
7 Choose an Internet connection type:
PPPoE: Choose this option if you have obtained PPPoE credentials from the ISP.
Manual IP: Choose this option if you have obtained an available IP address for use.
Auto IP: Choose this option if you rely on an ISP modem for automatic IP assignment.
12
Chapter 2: Hardware Setup
8 The wizard will continue to set up your RT6600ax, and it may take up to three minutes to complete the setup.
9 After the setup is complete, click Start managing now to enjoy SRM and its various features.
Note:
1. Above is a general demonstration of the SRM setup steps. The steps and available options may
somewhat vary depending on your device type (e.g. PC or wireless device), access type (LAN, WAN, or
Wireless LAN), and chosen operation mode (Wireless Router or Wireless AP).
2. If the setup is to be completed with a wireless device, remember to download DS router to manage
your RT6600ax from anywhere.
13
Chapter 2: Hardware Setup
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Operations in the 5.15-5.25GHz band are restricted to indoor usage only.
This device meets all the other requirements specified in Part 15E, Section 15.407 of
the FCC Rules.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 21cm between the radiator & your body.
Note: The country code selection is for non-US model only and is not available to all
US model. Per FCC regulation, all WiFi product marketed in US must fixed to US
operation channels only.
Industry Canada statement:
This device complies with ISED’s licence-exempt RSSs. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause
undesired operation.
Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux conditions suivantes : (1) le dispositif ne doit pas
produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y
compris un brouillage susceptible de provoquer un fonctionnement indésirable.
Caution :
(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce
the potential for harmful interference to co-channel mobile satellite systems;
(ii) for devices with detachable antenna(s), the maximum antenna gain permitted for
devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment
still complies with the e.i.r.p. limit;
(iii) for devices with detachable antenna(s), the maximum antenna gain permitted
for devices in the band 5725-5850 MHz shall be such that the equipment still
complies with the e.i.r.p. limits as appropriate;
(iv) where applicable, antenna type(s), antenna models(s), and worst-case tilt angle(s)
necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in
section 6.2.2.3 shall be clearly indicated.
Avertissement:
Le guide d’utilisation des dispositifs pour réseaux locaux doit inclure des
instructions précises sur les restrictions susmentionnées, notamment :
(i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement
pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux
systèmes de satellites mobiles utilisant les mêmes canaux;
(ii) pour les dispositifs munis d’antennes amovibles, le gain maximal d’antenne permis
pour les dispositifs utilisant les bandes de 5 250 à 5 350 MHz et de 5 470 à 5 725 MHz doit
être conforme à la limite de la p.i.r.e;
(iii) pour les dispositifs munis d’antennes amovibles, le gain maximal d’antenne permis
(pour les dispositifs utilisant la bande de 5 725 à 5 850 MHz) doit être conforme à la limite
de la p.i.r.e. spécifiée, selon le cas;
(iv) lorsqu’il y a lieu, les types d’antennes (s’il y en a plusieurs), les numéros de
modèle de l’antenne et les pires angles d’inclinaison nécessaires pour rester
conforme à l’exigence de la p.i.r.e. applicable au masque d’élévation, énoncée à la
section 6.2.2.3, doivent être clairement indiqués
Radiation Exposure Statement:
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with greater than 20cm
between the radiator & your body.
claration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements ISED établies pour
un environnement non contrôlé. Cet équipement doit être installé et utilisé à plus de 20 cm
entre le radiateur et votre corps.
DETACHABLE ANTENNA USAGE
This radio transmitter [IC: 20954-RT6600ax] has been approved by Innovation,
Science and Economic Development Canada to operate with the antenna types
listed below, with the maximum permissible gain indicated. Antenna types not
included in this list that have a gain greater than the maximum gain indicated
for any type listed are strictly prohibited for use with this device.
Le présent émetteur radio [IC: 20954-RT6600ax] a é approuvé par Innovation,
Sciences et Développement économique Canada pour fonctionner avec les types
d'antenne énumés ci-dessous et ayant un gain admissible maximal. Les types
d'antenne non inclus dans cette liste, et dont le gain est supérieur au gain
maximal indiqué pour tout type figurant sur la liste, sont strictement interdits
pour l'exploitation de l'émetteur.
Manufacturer
Model
Antenna Type
Max Gain (dBi)
Impedance
(Ω)
LYNwave
ALX21X-221031-00
Dipole
2412-2462MHz: 2.00
5180-5320MHz: 3.00
50
LYNwave
ALX21X-221032-00
Dipole
2412-2462MHz: 2.00
5180-5320MHz: 3.00
50
LYNwave
ALX21X-221033-00
Dipole
5500-5825MHz: 3.00
5845-5885MHz: 3.30
50
LYNwave
ALX21X-221034-00
Dipole
5500-5825MHz: 3.00
5845-5885MHz: 3.30
50
LYNwave
ALX21X-221035-00
Dipole
5500-5825MHz: 3.00
5845-5885MHz: 3.30
50
LYNwave
ALX21X-221036-00
Dipole
5500-5825MHz: 3.00
5845-5885MHz: 3.30
50
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18

Synology RT6600ax Guide d'installation

Catégorie
Points d'accès WLAN
Taper
Guide d'installation

dans d''autres langues