Synology RT6600ax Guide d'installation

Synology Router RT6600ax

Hardware Installation Guide

Table of Contents

Chapter 1: Before You Start

Package Contents

3

Synology RT6600ax at a Glance

4

LED Indicator Table

5

Hardware Specification

6

Safety Instructions

7

Chapter 2: Hardware Setup

Adjust Antennas

8

Position Your RT6600ax

8

Connect to Your RT6600ax

9

Set up Synology Router Manager (SRM)

11

Synology_HIG_RT6600ax_20211208

2

1Chapter

Before You Start

Thank you for purchasing this Synology product! Before setting up your new expansion unit, please check the

package contents to verify that you have received the items below. Also, make sure to read the safety

instructions carefully to avoid harming yourself or damaging your expansion unit.

Note: All images below are for illustrative purposes only, and may differ from the actual product.

Package Contents

Main unit x 1

AC power adapter x 1

RJ-45 LAN cable x 1

3

Synology RT6600ax at a Glance

1

2

3

4

5 6 7

1213

10

8

9 11

No.

Article Name

Location

Description

1

USB 3.0 Port

Connect an external drive, USB printer, or other types of USB

devices here.

2

WAN Port

Connect a network cable from the ISP modem into this port to

establish WAN connection.

1. Connect a network cable from the ISP modem into this port to

3

2.5G WAN/LAN Port

establish WAN connection.

2. Connect network cables into these ports to establish LAN

Rear Panel

connection.

4

LAN Port

Connect network cables into these ports to establish LAN

connection.

5

Power Button

Press to power on/off the Synology Router.

6

RESET Button

Press and hold for four seconds (Soft Reset) or for ten seconds

(Hard Reset).

7

Power Port

Connect the AC power adapter here.

8

LAN Indicator

Displays the status of LAN connection.

9

WAN Indicator

Front Panel

Displays the status of WAN connection.

10

Wi-Fi Indicator

Displays the status of Wi-Fi connection.

11

STATUS Indicator

Displays the status of the system.

12

WPS Button

Right Panel

Press to start WPS.

13

Wi-Fi Button

Press to turn on/off the Wi-Fi network.

4

Chapter 1: Before You Start

LED Indicator Table

LED Indicator

Color

Status

Description

Green

Static

Powered on

Blinking

System Ready

Static

System booting/Rebooting/Hard Reset

Status Indicator

Orange

Blinking

Restoring settings (Soft Reset)/Mesh

network disconnected

Green/Orange

Blinking

Searching device

Off

Powered off

Green

Static

Wi-Fi active

Wi-Fi

Blinking

WPS connecting

Off

No Wi-Fi

Green

Static

Network connected

WAN

Blinking

Data transmitting

Off

Network disconnected

Green

Static

Gigabit/2.5G connection

Blinking

Gigabit/2.5G data transmitting

LAN 1

Orange

Static

10/100 Mbps connection

Blinking

10/100 Mbps data transmitting

Off

No network

Green

Static

Gigabit connection

Blinking

Gigabit data transmitting

LAN 2-4

Orange

Static

10/100 Mbps connection

Blinking

10/100 Mbps data transmitting

Off

No network

5

Chapter 1: Before You Start

Hardware Specification

Item

RT6600ax

External Ports

USB 3.0 x 1

WAN Port

• Gigabit WAN x 1

• Gigabit WAN x 1 and 2.5G WAN x 1 (Dual WAN)

LAN Ports

• Gigabit LAN x 3 and 2.5G LAN x 1

• Gigabit LAN x 3 (Dual WAN)

Size (H x W x D) (mm)

65 x 280 x 180 (without antennas)

Weight (kg)

0.9 kg

Supported Clients

• Windows 7 onwards

(for SRM management)

• Mac OS 10. 12 onwards

File Systems

External: EXT4, EXT3, FAT, NTFS, HFS+

Wireless Standards

• 2.4GHz: 802.11 b/g/n/ax

• 5GHz: 802.11 a/n/ac/ax

• 802.11ax (2.4GHz): Up to 600 Mbps

Operating Frequency Range

• 802.11ax (5GHz-1): Up to 1200 Mbps

• 802.11ax (5GHz-2): Up to 4800 Mbps

Wireless Operation Modes

• Wireless Router

• Wireless AP (Access Point)

• 64/128-bit WEP • WPS support

• WPA2-Personal • WPA/WPA2-Personal

Wireless Security

• WPA2-Enterprise • WPA/WPA2-Enterprise

• Opportunistic Wireless Encryption (OWE)

• WPA3-Personal • WPA3-Enterprise

• WPA2/WPA3-Personal

Antennas

• 2T2R Omni-directional high-gain dipole (2.4GHz/5GHz-1)

• 4T4R Omni-directional high-gain dipole (5GHz-2)

Buttons & Switches

• Power • WPS • Wi-Fi On/Off • Reset

Language Localization

• Line voltage: 100V to 240V AC

• Frequency: 50/60Hz

Environment Requirements

• Operating Temperature: 40 to 104˚F (5 to 40˚C)

• Storage Temperature: -5 to 140˚F (-20 to 60˚C)

• Relative Humidity: 5% to 95% RH

Note: Model specifications are subject to change without notice. Please refer to www.synology.com for the latest information.

6

Chapter 1: Before You Start

Safety Instructions

Keep away from direct sunlight and away from chemicals. Ensure a stable environment

with no abrupt changes in temperature or humidity.

Place the unit right side up at all times.

Keep the unit away from liquids.

Before cleaning, unplug the power cord. Do not use chemical or aerosol cleaners. Wipe

with damp paper towels.

To prevent the unit from falling over, do not place it on carts or any unstable surfaces.

The power cord must plug into the correct supply voltage. Ensure the supplied AC

voltage is correct and stable.

Warning, electric shock hazard. To remove all electrical current from the device,

ensure that all power cords are disconnected from the power source.

Risk of explosion if the battery is replaced by an incorrect type. Dispose of used batteries

appropriately.

Power cord must be plugged into a socket-outlet with earthing connection.

Keep body parts away from moving fan.

This product must be installed by qualified personnel in a restricted access location (like

dedicated equipment rooms, service closets).

7

Chapter 1: Before You Start

2Chapter

Hardware Setup

Adjust Antennas

For optimal Wi-Fi performance, tilt the antennas so that they are at a 90 degree angle to the surface.

Position Your RT6600ax

For optimal performance, it is recommended to position your RT6600ax as advised below:

• On a stable surface (e.g. an elevated shelf) away from any possible physical interruptions.

• Close to the center of the area where the wired/wireless client devices are placed, and within a visible

distance from the wireless devices.

• In a position where few walls and ceilings are between your RT6600ax and its client devices.

• Away from any potential electrical signal sources, such as other Wi-Fi routers, 3G/4G bases, and

microwave ovens.

• Away from large expanses of metal or other materials, such as metal doors, glass panels, and concrete.

Place Flat on a Surface

Simply place your RT6600ax flat on a horizontal, stable surface.

8

Connect to Your RT6600ax

1 Use the included network cable to connect your RT6600ax (at the WAN1 port) to the ISP modem. Connect

one end of the power adapter to the power port on your RT6600ax, and the other end to the power outlet.

Press the power button to power on your RT6600ax. Wait for up to two minutes until the STATUS and WAN

LED indicators turn green.

2 Connect wireless client devices to your RT6600ax. When the Wi-Fi indicator has turned static green,

RT6600ax is ready to connect with other devices. Use your wireless device to scan and join the Wi-Fi network

created by your RT6600ax.

Note:

The default credentials for the Wi-Fi network:

• Wi-Fi SSID: Synology_(Serial)

• Password: synology

You can change it during the initial SRM setup.

9

Chapter 2: Hardware Setup

3 Connect wired client devices to your RT6600ax. Use network cables to connect devices to the LAN ports.

The corresponding LAN LED indicators should turn orange/green to indicate successful connection.

10

Chapter 2: Hardware Setup

Set up Synology Router Manager (SRM)

1 Use a computer or wireless device connected to your RT6600ax's local network. If you use a wireless device,

scan and join the Wi-Fi network (SSID: Synology_(Serial); Password: synology).

2 Open a web browser, and enter either URL into the address bar:

• http://router.synology.com

• http://192.168.1.1:8000

3 Once connected, click Start to launch the SRM Setup Wizard.

4 Fill in the information to set up the administrator account. Click Next to continue.

11

Chapter 2: Hardware Setup

5 Fill in the information to set up the Wi-Fi network. Click Next to continue.

6 Set up the operation mode. When choosing the Wireless Router mode, you can also enable External

access to SRM so that only external access via the HTTP(S) port (e.g. 8000/8001) can reach SRM.

7 Choose an Internet connection type:

• PPPoE: Choose this option if you have obtained PPPoE credentials from the ISP.

• Manual IP: Choose this option if you have obtained an available IP address for use.

• Auto IP: Choose this option if you rely on an ISP modem for automatic IP assignment.

12

Chapter 2: Hardware Setup

8 The wizard will continue to set up your RT6600ax, and it may take up to three minutes to complete the setup.

9 After the setup is complete, click Start managing now to enjoy SRM and its various features.

Note:

1. Above is a general demonstration of the SRM setup steps. The steps and available options may

somewhat vary depending on your device type (e.g. PC or wireless device), access type (LAN, WAN, or

Wireless LAN), and chosen operation mode (Wireless Router or Wireless AP).

2. If the setup is to be completed with a wireless device, remember to download DS router to manage

your RT6600ax from anywhere.

13

Chapter 2: Hardware Setup

Federal Communication Commission Interference Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the

interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to operate this equipment.

This transmitter must not be co-located or operating in conjunction with any other

antenna or transmitter.

Operations in the 5.15-5.25GHz band are restricted to indoor usage only.

This device meets all the other requirements specified in Part 15E, Section 15.407 of

the FCC Rules.

Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an

uncontrolled environment. This equipment should be installed and operated with

minimum distance 21cm between the radiator & your body.

Note: The country code selection is for non-US model only and is not available to all

US model. Per FCC regulation, all WiFi product marketed in US must fixed to US

operation channels only.

Industry Canada statement:

This device complies with ISED’s licence-exempt RSSs. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and (2)

this device must accept any interference received, including interference that may cause

undesired operation.

Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils radio exempts de

licence. L’exploitation est autorisée aux deux conditions suivantes : (1) le dispositif ne doit pas

produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y

compris un brouillage susceptible de provoquer un fonctionnement indésirable.

Caution :

(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce

the potential for harmful interference to co-channel mobile satellite systems;

(ii) for devices with detachable antenna(s), the maximum antenna gain permitted for

devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment

still complies with the e.i.r.p. limit;

(iii) for devices with detachable antenna(s), the maximum antenna gain permitted

for devices in the band 5725-5850 MHz shall be such that the equipment still

complies with the e.i.r.p. limits as appropriate;

(iv) where applicable, antenna type(s), antenna models(s), and worst-case tilt angle(s)

necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in

section 6.2.2.3 shall be clearly indicated.

Avertissement:

Le guide d’utilisation des dispositifs pour réseaux locaux doit inclure des

instructions précises sur les restrictions susmentionnées, notamment :

(i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement

pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux

systèmes de satellites mobiles utilisant les mêmes canaux;

(ii) pour les dispositifs munis d’antennes amovibles, le gain maximal d’antenne permis

pour les dispositifs utilisant les bandes de 5 250 à 5 350 MHz et de 5 470 à 5 725 MHz doit

être conforme à la limite de la p.i.r.e;

(iii) pour les dispositifs munis d’antennes amovibles, le gain maximal d’antenne permis

(pour les dispositifs utilisant la bande de 5 725 à 5 850 MHz) doit être conforme à la limite

de la p.i.r.e. spécifiée, selon le cas;

(iv) lorsqu’il y a lieu, les types d’antennes (s’il y en a plusieurs), les numéros de

modèle de l’antenne et les pires angles d’inclinaison nécessaires pour rester

conforme à l’exigence de la p.i.r.e. applicable au masque d’élévation, énoncée à la

section 6.2.2.3, doivent être clairement indiqués

Radiation Exposure Statement:

This equipment complies with ISED radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with greater than 20cm

between the radiator & your body.

Déclaration d'exposition aux radiations:

Cet équipement est conforme aux limites d'exposition aux rayonnements ISED établies pour

un environnement non contrôlé. Cet équipement doit être installé et utilisé à plus de 20 cm

entre le radiateur et votre corps.

DETACHABLE ANTENNA USAGE

This radio transmitter [IC: 20954-RT6600ax] has been approved by Innovation,

Science and Economic Development Canada to operate with the antenna types

listed below, with the maximum permissible gain indicated. Antenna types not

included in this list that have a gain greater than the maximum gain indicated

for any type listed are strictly prohibited for use with this device.

Le présent émetteur radio [IC: 20954-RT6600ax] a été approuvé par Innovation,

Sciences et Développement économique Canada pour fonctionner avec les types

d'antenne énumérés ci-dessous et ayant un gain admissible maximal. Les types

d'antenne non inclus dans cette liste, et dont le gain est supérieur au gain

maximal indiqué pour tout type figurant sur la liste, sont strictement interdits

pour l'exploitation de l'émetteur.

Manufacturer

Model

Antenna Type

Max Gain (dBi)

Impedance

(Ω)

LYNwave

ALX21X-221031-00

Dipole

2412-2462MHz: 2.00

5180-5320MHz: 3.00

50

LYNwave

ALX21X-221032-00

Dipole

2412-2462MHz: 2.00

5180-5320MHz: 3.00

50

LYNwave

ALX21X-221033-00

Dipole

5500-5825MHz: 3.00

5845-5885MHz: 3.30

50

LYNwave

ALX21X-221034-00

Dipole

5500-5825MHz: 3.00

5845-5885MHz: 3.30

50

LYNwave

ALX21X-221035-00

Dipole

5500-5825MHz: 3.00

5845-5885MHz: 3.30

50

LYNwave

ALX21X-221036-00

Dipole

5500-5825MHz: 3.00

5845-5885MHz: 3.30

50

Synology RT6600ax Guide d'installation

Synology RT6600ax Guide d'installation

dans d''autres langues