Superior Fireplaces Signature DRT6340TYN Guide d'installation

Marque: Superior Fireplaces

Modèle: Signature DRT6340TYN

Catégorie: Cheminées

Taper: Guide d'installation

Ce manuel convient également à

03/01/2013

MODELS

This appliance may be installed in an aftermarket permanently located, manufactured home (USA only) or mobile

home, where not prohibited by local codes. This appliance is only for use with the type of gas indicated on the rating

plate. This appliance is not convertible for use with other gases.

INSTALLATION INSTRUCTIONS

Montebello® DLX Power Vent

Direct-Vent Gas Fireplaces

P/N 506023-26 Rev. NC 12/2013

This manual is one of a set of two supporting this product.

Refer to P/N

506025-18

for Care and Operation Instructions.

Ce manuel est disponible en francais, simplement

en faire la demande. Numéro de la pièce 506023-27.

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

INSTALLATEUR : Laissez cette notice avec l'appareil.

CONSOMMATEUR : Conservez cette notice pour

consultation ultérieure.

Intertek Report No.

100513650PRT-001

AVERTISSEMENT : Assurez-vous de bien suivre les

instructions données dans cette notice pour réduire au

minimum le risque d’incindie ou d’explosion ou pour

éviter tout dommage matériel, toute blessure ou la mort.

WARNING: If the information in these instructions

is not followed exactly, a ﬁre or explosion may

result, causing property damage, personal injury,

or death.

WARNING /AVERTISSEMENT/AVISO

HOT GLASS WILL

CAUSE BURNS.

DO NOT TOUCH GLASS

UNTIL COOLED

NEVER ALLOW CHILDREN

TO TOUCH GLASS.

UNE SURFACE VITRÉE CHAUDE

PEUT CAUSER DES BRÛLURES.

LAISSER REFROIDIR LA SURFACE

VITRÉE AVANT D'Y TOUCHER.

NE PERMETTEZ JAMAIS À UN ENFANT

DE TOUCHER LA SURFACE VITRÉE.

EL VIDRIO CALIENTE

CAUSARÁ QUEMADURAS.

USTED DEBE NUNCA

TOCAR EL VIDRIO CALIENTE.

LOS NIÑOS DEBEN NUNCA

TOCAR EL VIDRIO.

- Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any other

appliance.

- WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any

phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call the fire

department.

- Installation and service must be performed by a

qualified installer, service agency or the gas supplier.

- Ne pas entreposer ni utilizer d’essence ni d’autres vapeurs

ou liquides inﬂammables dans le voisinage de cet appareil

ou de tout autre appareil.

- QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ :

• Ne pas tenter d’allumer d’appareil.

• Ne touchez à aucan interrupteur. Ne pas vous servir des

téléphones se trouvant dans le bâtiment où vous trouvez.

• Appelez immédiatement votre fournisseur de gaz depuis

un voisin. Suivez les instructions du fournisseur.

• Si vous ne pouvez rejoindre le fournisseur de gaz,

appelez le service des incindies.

- L’installation et l’entretien doivent être assurés par un

installateur ou un service d’entretien qualiﬁé ou par le

fournisseur de gaz.

MontebelloDLX45TYN

MontebelloDLXCD45TYN

MontebelloDLX40TYN

MontebelloDLXCD40TYN

Decorative Product: Not for use as a heating appliance.

NOTICE: Fireplace is not to be operated by a thermostat.

WARNING

Young children should be care-

fully supervised when they are

in the same room as the appli-

ance. Toddlers, young children

and others may be susceptible

to accidental contact burns. A

physical barrier is recommended

if there are at risk individuals in

the house. To restrict access to

a ﬁreplace or stove, install an

adjustable safety gate to keep

toddlers, young children and

other at risk individuals out of

the room and away from hot

surfaces.

AVERTISSEMENT

Les jeunes enfants devraient être

surveillés étroitement lorsqu’ils

se trouvent dans la même pièce

que l’appareil. Les tout petits,

les jeunes enfants ou les adultes

peuvent subir des brûlures s’ils

viennent en contact avec la sur-

face chaude. Il est recommandé

d’installer une barrière physique

si des personnes à risques habi-

tent la maison. Pour empêcher

l’accès à un foyer ou à un poêle,

installez une barrière de sécu-

rité; cette mesure empêchera les

tout petits, les jeunes enfants et

toute autre personne à risque

d’avoir accès à la pièce et aux

surfaces chaudes.

GENERAL INFORMATION

INNOVATIVE HEARTH PRODUCTS • POWER VENT DV GAS FIREPLACES (MontebelloDLX__TYN / MontebelloDLXCD__TYN) • INSTALLATION INSTRUCTIONS

TABLE OF CONTENTS

Packaging .........................................Page 2

Introduction ......................................Page 2

General Information ..........................Page 2

Massachusetts Requirements ...........Page 4

Cold Climate Insulation .....................Page 5

Manufactured Home Requirements ..Page 5

Location ............................................Page 5

Vent Termination Clearances ............ Page 6

Minimum Clearances to Combustibles Page 8

Pre-Installation Steps ........................ Page 9

Typical Installation Sequence ...........Page 9

Detailed Installation Steps ................. Page 9

Step 1. Framing ............................... Page 9

Fireplace and Framing Specications Page 10

Step 2. Routing Gas Line ................Page 11

Proper Sizing of Gas Line ..................Page 11

Step 3. Install the Vent System .......Page 12

General Vent Information ..................Page 12

Power Vent Components...................Page 12

Vent Section Length Chart ................Page 13

Offset Installation ..............................Page 13

Horizontal Termination System .........Page 16

Installing Power Vent Termination ....Page 16

Step 4. Field Wiring ......................... Page 18

Step 5. Removing Glass Door Frame Assem-

bly Page .................................... 20

Step 6. Connecting Gas Line ...........Page 21

Step 7 Install Firebox Liner ............Page 21

Step 8. Verifying Appliance

Operation ..........................................Page 21

Step 9. Installing Logs ...................Page 22

Step 10. Install/Remove Glass

Door Assembly .................................Page 24

Step 11. Burner Adjustments ............Page 24

Finishing Requirements ....................Page 26

Step 12. Attaching Safety-in-

Operation Warnings ...................

Page 27

Installation Accessories ....................Page 28

Please read and understand these instruc-

tions before beginning your installation.

PACKAGING

The assembled vented gas fireplace is packaged with:

BOX 1 - Fireplace:

• Literature Kit (plastic bag shipped

inside rebox),

• Bags of Glowing Embers, Platinum Embers,

and Volcanic Stone

• Pull Screen

• Door Modesty Shield

• Adaptor with Probe Assembly

• (1) Remote Control Kit and Receiver Kit

BOX 2 - Power Vent Components:

• (1) Power Vent Termination

• (1) Termination Adaptor

• (1) Horizontal Firestop Assembly

• (1) Vacuum Hose

• (1) 11/32" Hose Clamp

• (1) Strain Relief

• (1) Bushing

• (4) Insulated 1/4" Male Terminals

• (2) #10 Ring Terminals

BOX 3 - Firebox Liner Panels:

In one of the following panel styles:

• Ceramic Liner Kit - Buff Rustic

• Ceramic Liner Kit - Red Rustic

• Porcelain Liner Kit - Black

• Ceramic Liner Kit - Red Herringbone

• Ceramic Liner Kit - Buff Herringbone

INTRODUCTION

These Electronic appliances are designed to

operate on natural gas and have an electronic

intermittent pilot ignition system. External 120

Volt AC electrical power is required to operate

these units.

These vented gas replaces are sealed combus-

tion gas replaces designed for residential,

manufactured home, and commercial ap-

plications.

Use Only These Approved Vent Components

These replaces are designed, tested and

listed for operation and installation with, the

following (4-1/2" inner and 7-1/2" outer) vent

components only:

• Secure Vent® Direct-vent system compo-

nents manufactured by Security Chimneys

International.

These approved vent system components are

labeled for identication. Do NOT use any other

manufacturer’s vent components with these

appliances.

Children and adults should be alerted to the haz-

ards of high surface temperature and should stay

away to avoid burns or clothing ignition.

Les enfants et les adultes devraient être

infor-més des dangers que posent les tem-

pératures de surface élevées et se tenir à

distance aﬁn d’éviter des brûlures ou que

leurs vêtements ne s’enﬂamment.

DO NOT ATTEMPT TO ALTER OR MODIFY

THE CONSTRUCTION OF THE APPLIANCE

OR ITS COMPONENTS. ANY MODIFICATION

OR ALTERATION MAY VOID THE WARRANTY,

CERTIFICATION AND LISTINGS OF THIS UNIT.

Installation and repair should be done by

a qualiﬁed service person. The appliance

should be inspected before use and at least

annually by a professional service person.

More frequent cleaning may be required due

to excessive lint from carpeting, bedding

material, etcetera. It is imperative that control

compartments, burners and circulating air

passageways of the appliance be kept clean.

L’installation et la réparation devrait

être conﬁées à un technicien qualiﬁé.

L’appareil devrait faire l’objet d’une in-

spection par un technicien professionnel

avant d’être utilisé et au moins une fois

l’an par la suite. Des nettoyages plus

fréquents peuvent être nécessaires si les

tapis, la literie, et cetera produisent une

quantité importante de pous-sière. Il est

essentiel que les compartiments abritant

les commandes, les brûleurs et les con-

duits de circulation d’air de l’appareil

soient tenus propres.

Do not use this appliance if any part has been

under water. Immediately call a qualiﬁed ser-

vice technician to inspect the appliance and

to replace any part of the control system and

any gas control which has been under water.

Ne pas utiliser cet appareil s’il a été

plongé, même partiellement, dans

l’eau. Appeler un technicien qualiﬁé pour

inspecter l’appareil et remplacer toute

partie du système de commande et toute

commande qui a été plongée dans l’eau.

Only trim kit(s) supplied by the manufacturer

shall be used in the installation of this ap-

pliance.

Seules les trousses de garniture fournies

par le fabricant doivent être utilisées pour

l’installation de cet appareil.

WARNING

Failure to position the parts in

accordance with these diagrams

or failure to use only parts speciﬁ-

cally approved with this appliance

may result in property damage or

personal injury.

AVERTISSEMENT

Risque de dommages ou de

blessures si les pièces ne sont

pas installées conformément à

ces schémas et ou si des pièces

autres que celles spéciﬁquement

approuvées avec cet appareil sont

utilisées.

WARNING

Clothing or other flammable

material should not be placed

on or near the appliance.

AVERTISSEMENT

On ne devrait pas placer de

vêtements ni d’autres matières

inﬂammables sur l’appareil ni

à proximité.

WARNING

Improper installation or use of

this appliance can cause serious

injury or death from ﬁre, burns,

explosion or carbon monoxide

poisoning.

INNOVATIVE HEARTH PRODUCTS • POWER VENT DV GAS FIREPLACES (MontebelloDLX__TYN / MontebelloDLXCD__TYN) • INSTALLATION INSTRUCTIONS

WARNING

Improper installation, adjust-

ment, alteration, service or

maintenance can cause injury

or property damage. Refer to

this manual. For assistance or

additional information consult

a qualified installer, service

agency or the gas supplier.

WARNING

Failure to comply with these

installation instructions will

result in an improperly installed

and operating appliance, voiding

its warranty. Any change to this

appliance and/or its operating

controls is dangerous.

WARNING

Any safety screen or guard

removed for servicing the appli-

ance must be replaced prior to

operating the appliance.

AVERTISSEMENT

Tout écran ou protecteur retiré

pour permettre l’entretien de

l’appareil doit être remis en

place avant de mettre l’appareil

en marche.

Codes and Standards

These appliances comply with National Safety

Standards and are tested and listed by Intertek

(Report No. 100513650) to Z21.50b-2009

(in Canada, CSA-2.22b-2009), and CAN/

CGA-2.17-M91 (R2009) in both USA and

Canada, as vented gas replaces.

These appliances are listed by Intertek for

installation in bedrooms and manufactured

(mobile) homes.

Installation must conform to local codes. In the

absence of local codes, installation must comply

with the current National Fuel Gas Code, ANSI

Z223.1/NFPA 54 (in Canada, the current CAN/

CGA-B149.1 installation code).

The appliance, when installed, must be electri-

cally grounded in accordance with local codes

or, in the absence of local codes, with the

National Electrical Code, ANSI/NFPA 70 - latest

edition, or the Canadian Electrical Code, CSA

C22.1 - latest edition.

Provide adequate clearances around air open-

ings and adequate accessibility clearance for

service and proper operation. Never obstruct

the front openings of the appliance.

These appliances are designed to operate on

natural gas. The use of other fuels or combina-

tion of fuels will degrade the performance of

this system and may be dangerous.

These appliances must not be connected to a

chimney or ﬂue serving a separate solid fuel

burning appliance.

These electronic appliances are remotely con-

trolled and feature an electronic intermittent

pilot ignition system. External electrical power

is required to operate these units.

These electronic models come standard with a

remotely-modulated gas valve; ﬂame appear-

ance and heat output cannot be controlled at the

gas valve. The BTU Input for these appliances

is shown in Table 1.

Input (BTU/HR), Natural Gas

Model No. Input (BTU/Hr)

40 in. 26,500 - 42,000

45 in. 35,000 - 48,000

Table 1

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

In Canada - CAN/CGA-2.17-M91 (R2009) (high

altitude):

THE CONVERSION SHALL BE CARRIED OUT

BY A MANUFACTURER’S AUTHORIZED REP-

RESENTATIVE, IN ACCORDANCE WITH THE

REQUIREMENTS OF THE MANUFACTURER,

PROVINCIAL OR TERRITORIAL AUTHORITIES

HAVING JURISDICTION AND IN ACCORDANCE

WITH THE REQUIREMENTS OF THE CAN/CGA-

B149.1 OR CAN/CGA-B149.2 INSTALLATION

CODES.

REQUIREMENTS FOR THE COMMON-

WEALTH OF MASSACHUSETTS

These replaces are approved for installation in

the US state of Massachusetts if the following

additional requirements are met:

• Install this appliance in accordance with

Massachusetts Rules and Regulations 248

C.M.R.

• Installation and repair must be done by a

plumber or gas tter licensed in the Com-

monwealth of Massachusetts.

• The exible gas line connector used shall

not exceed 36 in. (92 centimeters) in length.

• The individual manual shut-off must be a

T-handle type valve.

Massachusetts Horizontal Vent Requirements

In the Commonwealth of Massachusetts, hori-

zontal terminations installed less than seven

(7) feet above the ﬁnished grade must comply

with the following additional requirements:

• A hard wired carbon monoxide detector

with an alarm and battery back-up must be

installed on the ﬂoor level where the gas

replace is installed. The carbon monoxide

detector must comply with NFPA 720, be

ANSI/UL 2034 listed and be ISA certied.

• A metal or plastic identication plate must

be permanently mounted to the exterior of

the building at a minimum height of eight (8)

feet above grade and be directly in line with

the horizontal termination. The sign must

read, in print size no less than one-half (1/2)

inch in size, GAS VENT DIRECTLY BELOW.

KEEP CLEAR OF ALL OBSTRUCTIONS.

Gas Valve Diagram

See Figure 1 for gas valve diagram.

Figure 1 - SIT Electronic Gas Valve

Wire

(From DFC Wire

Harness)

Pressure

Regulator

Tower

Yellow Ground Wire

(From DFC Wire

Harness)

Green Wire

(From DFC Wire

Harness)

Inlet (In) Test Port

Manifold (Out)

Test Port

Connect GTMS

Wire Harness

Main Gas Inlet

3/8" NPT

Test gauge connections are provided on the front

of the gas control valve; identied IN for the inlet

and OUT for the manifold side (see Figure 1).

Oriﬁce Sizes - Sea Level To High Altitude

These appliances are tested and approved for

installation at elevations of 0 - 4500 ft (0 - 1370

m) above sea level, using the standard burner

orice sizes (marked with an "*" in Table 4).

For elevations above 4500 ft, contact your gas

supplier or qualied service technician.

Deration - At higher elevations, the amount

of BTU fuel value delivered must be reduced

by either:

• Using gas that has been derated by the gas

company.

• Changing the burner orice to a smaller size

as regulated by the local Authorities Having

Jurisdiction and by the (USA) National Fuel

Gas Code NFPA 54/ANSI Z223.1 - latest

edition, or in Canada, the CAN/CGA-B149.1

code - latest edition.

Install the appliance according to the regulations

of the local authorities having jurisdiction, and

the (USA) National Fuel Gas Code NFPA 54 /

ANSI Z223.1 - latest edition,

or (Canada) CAN/CGA-B149.1 - latest edition.

NOTE: Flame appearance will diminish 4%

per one thousand feet of altitude.

The appliance and its appliance main gas

valve must be disconnected from the gas

supply piping system during any pressure

testing of that system at test pressures in

excess of 1/2 psi (3.5 kPa).

The appliance must be isolated from the gas

supply piping system by closing its equipment

shutoff valve during any pressure testing of

the gas supply piping system at test pres-

sures equal to or less than 1/2 psi (3.5 kPa).

PURGE CYCLE

This is a power vented ﬁreplace that

requires household electrical power

to operate. It will not operate during

a power failure. When the ﬁreplace

is turned off, the exhaust blower will

continue to operate for approximately

ﬁfteen (15) seconds after shutdown

to expel the exhaust gases from the

venting system.

Burner Oriﬁce Size

Elevation 0 - 4500 ft (0 - 1370 m)

Model Oriﬁce Size / Catalog Number

Traditional

40 in. 0.125" (1/8") * H7924 •

45 in. 0.136" (#29) * H8141 •

Contemporary

40 in. 0.0700" (#50) *

45 in. 0.0700" (#50) *

Table 4 * Standard size installed at factory

• Part /Cat. Number

INNOVATIVE HEARTH PRODUCTS • POWER VENT DV GAS FIREPLACES (MontebelloDLX__TYN / MontebelloDLXCD__TYN) • INSTALLATION INSTRUCTIONS

Gas Pressure - All Models

Tables 2 and 3 show the appliance inlet and

manifold gas pressure requirements.

Inlet Gas Supply Pressure

Minimum Maximum

5.5" WC

(1.37 kPa)

10.5" WC

(2.62 kPa)

Table 2

Manifold Gas Supply Pressure

Low High

1.6" WC

(.40 kPa)

3.5" WC

(.87 kPa)

Table 3

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

COLD CLIMATE INSULATION

For cold climate installations, seal all cracks

around your appliance with noncombustible

material and wherever cold air could enter

the room. It is especially important to insulate

outside chase cavity between studs and under

oor on which appliance rests, if oor is above

ground level. Gas line holes and other open-

ings should be caulked or stuffed with unfaced

berglass insulation.

If the replace is being installed on a cement

slab in cold climates, a sheet of plywood or

other raised platform can be placed underneath

to prevent cold transfer to the replace and

into the room. It also helps to sheetrock inside

surfaces and tape for maximum air tightness

and caulk restops.

MANUFACTURED HOME

REQUIREMENTS

This appliance may be installed in an aftermar-

ket permanently located, manufactured home

and must be installed in accordance with the

manufacturer's instructions.

Cet appareil peut être installé cómme

du matéri-el d'origine dans une maison

préfabriquée (É.U. seulement) ou mobile

et doit être installé selon les instructions

du fabricant.

This appliance is only for use with the type of

gas indicated on the rating plate. This appliance

is not convertible for use with other gases.

Cet appareil doit être utilisé uniquement

avec le type de gaz indiqué sur la plaque

signalétique. Cet appareil ne peut être

converti à d'autres gaz.

CAUTION: Ensure that the cross mem-

bers are not cut or weakened during

installation. The structural integrity of

the manufactured home ﬂoor, wall, and

ceiling/roof must be maintained.

CAUTION: This appliance must be

grounded to the chassis of the manu-

factured home in accordance with local

codes or in the absence of local codes,

with the National Electrical Code ANSI /

NFPA 70 - latest edition.

LOCATION

In selecting the location, the aesthetic and

functional use of the appliance are primary

concerns. However, vent system routing to

the exterior and access to the fuel supply are

also important.

Due to high temperatures, the appliance

should be located out of trafﬁc and away from

furniture and draperies (Figure 2).

En raison des températures élevées,

l’appareil devrait être installé dans un

endroit où il y a peu de circulation et loin

du mobilier et des tentures (Figure 2).

The location should also be free of electrical,

plumbing or other heating/air conditioning

ducting.

Recessed

Application

Cross Corner

Application

Flat

Application

Flat on Wall

Application

Room Divider

Application

Island

Application

Figure 2 - Typical Installation

Top of Fireplace

Opening

Drywall

Noncombustible

Horizontal

Termination

Fireplace

Be aware that this is a heat producing ap-

pliance. Objects placed above the unit are

exposed to elevated temperatures.

Do not insulate the space between the appli-

ance and the area above it.

The appliance must be mounted on a fully

supported base extending the full width and

depth of the unit. The appliance may be lo-

cated on or near conventional construction

materials. However, if installed on combustible

materials, such as carpeting, vinyl tile, or other

combustible material other than wood ooring,

the appliance shall be installed on a metal or

wood panel extending the full width and depth

of the appliance.

NOTE: When the unit is installed

with one side ﬂush with a wall, the

wall on the other side of the unit

must not extend beyond the front

edge of the unit.

INNOVATIVE HEARTH PRODUCTS • POWER VENT DV GAS FIREPLACES (MontebelloDLX__TYN / MontebelloDLXCD__TYN) • INSTALLATION INSTRUCTIONS

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

VENT TERMINATION CLEARANCES

These instructions should be used as a guide-

line and do not supersede local codes in any

way. Install venting according to local codes,

these instructions, and the current (USA)

National Fuel Gas Code ANSI-Z223.1 / NFPA

54, or (Canada) CAN/CGA-B149.1 standards.

Horizontal Vent Termination Clearances

The horizontal vent termination must have

a minimum of 3" (76 mm) clearance to any

overhead combustible projection of 2-1/2" (64

mm) or less (see Figure 3). For projections

exceeding 2-1/2" (64 mm), see Figure 3. For

additional vent location restrictions refer to

Figure 4 on Page 7.

INNOVATIVE HEARTH PRODUCTS • POWER VENT DV GAS FIREPLACES (MontebelloDLX__TYN / MontebelloDLXCD__TYN) • INSTALLATION INSTRUCTIONS

See Figure 19 on Page 17 for the re-

cess allowances, into exterior walls,

of the power vent terminations.

Combustible Projection

2-1/2" or less in length

Combustible Projection

Greater than 2-1/2" in length

Ventilated or

Unventilated Sofﬁt

3".

(76 mm)

24"

(610 mm)

Power Vent Termination

Side Elevation View

Figure 3 - Horizontal Vent Termination Clearances

Combustible

18"

(457 mm)

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Minimum Clearances Canadian Installation * US Installation **

AClearance above grade, veranda, porch, deck or

balcony. 12" (30 cm) * 12" (30 cm) **

BClearance to window or door that may be opened.

6" (15.2 cm) for appliances < 10,000 BTU/hr (3kW),

12" (30 cm) for appliances > 10,000 BTU/hr (3kW)

and < 100,000 BTU/hr (30kW),

36" (91 cm) for appliances > 100,000 BTU/hr (30kW)*

6" (15.2 cm) for appliances < 10,000 BTU/hr (3kW),

9" (23 cm) for appliances > 10,000 BTU/hr (3kW) and

< 50,000 BTU/hr (15kW),

12" (30 cm) for appliances > 50,000 BTU/hr (15kW)*

CClearance to permanently closed window 12" (305 mm) recommended to prevent window

condensation

9" (229 mm) recommended to prevent window

condensation

Vertical clearance to ventilated soft located above

the terminal within a horizontal distance of 36"

(91.4cm) from the center line of the terminal 24" (61.0 cm) 24" (61.0 cm)

EClearance to unventilated soft 24" (61.0 cm) 24" (61.0 cm)

FClearance to outside corner 5" (12.7 cm) 5" (12.7 cm)

GClearance to inside corner 36" (91.4 cm) 24" (61.0 cm)

HClearance to each inside of center line extended

above meter / regulator assembly 3 ft (91 cm) within a height of 15 ft above the meter /

regulator assembly * 3 ft (91 cm) within a height of 15 ft above the meter /

regulator assembly **

IClearance to service regulator vent outlet 3 ft (91 cm) * 3 ft (91 cm) **

Clearance to non-mechanical air supply inlet to

building or the combustion air inlet to any other

appliance

6" (15.2 cm) for appliances < 10,000 BTU/hr (3kW),

12" (30 cm) for appliances > 10,000 BTU/hr (3kW)

and < 100,000 BTU/hr (30kW),

36" (91 cm) for appliances > 100,000 BTU/hr (30kW)*

6" (15.2 cm) for appliances < 10,000 BTU/hr (3kW),

9" (23 cm) for appliances > 10,000 BTU/hr (3kW) and

< 50,000 BTU/hr (15kW),

12" (30 cm) for appliances > 50,000 BTU/hr (15kW)*

KClearance to mechanical air supply inlet 6 ft (1.83 m) * 3 ft (91 cm) above, if within 10 ft (3 m) horizontally**

LClearance above paved sidewalk or paved

driveway located on public property 7 ft (2.13 m) ‡ 7 ft (2.13 m) ‡

M Clearance under veranda, porch, deck or balcony 18" (46.0 cm) * ‡ 18" (46.0 cm) ** ‡

* In accordance with the current CAN/CGA-B149.1 National Gas and B149.2 Propane Installation Code - Latest Editions.

** In accordance with the current ANSI Z223.1 / NFPA 54 National Fuel Gas Code - Latest Edition.

‡ A vent shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings and serves both dwellings.

*‡ Only permitted if veranda, porch, deck or balcony is fully open on a minimum 2 sides beneath the oor.

NOTE: Local Codes Or Regulations May Require

Different Clearances.

NOTE: Location Of The Vent Termination Must Not

Interfere With Access To The Electrical Service.

V V

X V

A A

X E

*18”

18”



* See Item D in the Text Below.

Center Line

of Termination

Exterior Wall

Horizontal

Termination

Ventilated Sofﬁt

Inside Corner

DETAIL D

Inside

Corner Detail

Operable

Window

Fixed

Closed

Window

= 9" in U.S.

=12" in Canada

3 ft.

= Air Supply Inlet = Vent Terminal = Area where Terminal is NOT permitted

24"

36"

Figure 4 - Exterior Horizontal Vent Termination Clearance Requirements

INNOVATIVE HEARTH PRODUCTS • POWER VENT DV GAS FIREPLACES (MontebelloDLX__TYN / MontebelloDLXCD__TYN) • INSTALLATION INSTRUCTIONS

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

* 3" (75 mm) above any horizontal/inclined vent component.

** See Page 9, Step 1 for clearance requirements to the nailing ange

located at each side of the unit and any screw heads adjacent to it.

Wall Finishes / Surrounds / Mantels

NOTE: Combustible wall nish materials and/or surround materials

must not be allowed to encroach the area deﬁned by the appliance

front face (black sheet metal). Never allow combustible materials to

be positioned in front of or overlapping the appliance face. See Figure

6 and Figure 44 on Page 26.

Noncombustible materials, such as surrounds and other appliance trim,

may be installed on the appliance front face with these exceptions: they

must not cover any portion of the removable glass panel.

Vertical installation clearances to combustible mantels vary according to

the depth of the mantel (see Figure 5). Mantels constructed of noncom-

bustible materials may be installed at any height above the appliance.

Minimum clearance requirements include any projections such as shelves,

window sills, mantels, etc. above the appliance.

NOTE: We recommend the use of high temperature paint (rated 175 °F

or higher) on the underside of the mantel.

MINIMUM CLEARANCES TO COMBUSTIBLES

Appliance And Vent Clearances

The appliance is approved with zero clearance to combustible materials

on all sides. Refer to Table 5 for minimum clearance values. For typical

installations, see Figure 2 on Page 5.

Figure 6 - Minimum Distance to Unprotected Side Wall

Figure 5 - Minimum Mantel Clearances

INNOVATIVE HEARTH PRODUCTS • POWER VENT DV GAS FIREPLACES (MontebelloDLX__TYN / MontebelloDLXCD__TYN) • INSTALLATION INSTRUCTIONS

MINIMUM CLEARANCES* Inches (millimeters)

Sides 1/2" (13 mm)

0" (0 mm) Spacers **

Top Spacers 0" (0 mm)

Floor 0" (0 mm)

Back 1/2" (13 mm)

0" (0 mm) Spacers

Bottom of Appliance To Ceiling 64" (1626 mm)

Vent 3" (76 mm) Top*

1" (25.4 mm) Sides and Bottom

SERVICE CLEARANCES Feet (meters)

Front 3 feet (0.9 meters)

Table 5

3-1/2”

(89 mm)

Top View of

Fireplace

Combustible materials

may project beyond

either side of the

fireplace opening as

long as they are kept

within the shaded

“Safe Zone” area.

At 0” minimum

side wall clearance,

one combustible

wall can project to

any length.

45o

Mantel Leg,

Trim, or Wall

12 (305) MANTEL

10 (254) MANTEL

8 (203) MANTEL

6 (152) MANTEL

4 (102) MANTEL

(102)

(356) 12

(305) 10

(254) 2 (51) MANTEL

TOP OF

APPLIANCE

(152)

(203)

MANTEL CLEARANCES

Inches (mm)

NOTE: Hood shown as positioned in louvered

front model. The hood position in the flush

faced front model is lower than shown.

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

PRE-INSTALLATION STEPS

The appliance is shipped with all gas controls

and components installed and pre-wired.

Before installing the appliance, follow these steps:

1. Remove the shipping carton.

2. Remove the shipping pad, exposing the front

glass door.

3. Using a Phillips screwdriver, unfasten the two

(2) screws located at the top of the glass frame

(see Figure 40 on Page 24). Tilt the top of the

glass frame away from the unit. Lift it carefully

off the bottom door track and set the door aside,

protecting it from inadvertent damage.

4. Remove the embers and volcanic stone from

the control compartment.

TYPICAL INSTALLATION SEQUENCE

The typical sequence of installation is outlined

below. However, each installation is unique and

may result in variations to the steps described.

See the page numbers references in the follow-

ing steps for detailed procedures.

Step 1. (Page 9) Construct the appliance

framing. Position the appliance within

the framing and secure with nailing

brackets.

Step 2. (Page 11) Route gas supply line to the

right side.

Step 3. (Page 12) Install the vent system and

exterior termination.

Step 4. (Page 18) Field Wiring

Connect 120 VAC electrical power to

the appliance receptacle.

Step 5. (Page 20) Remove glass door assem-

bly.

Step 6. (Page 21) Make connection to gas

supply.

Step 7. (Page 21) Install rebox liner kit.

Step 8. (Page 21) Verify appliance operation.

Step 9. (Page 22) Install volcanic stone, glow-

ing embers, and logs.

Step 10. (Page 24) Install glass door assembly.

Step 11. (Page 24) Adjust burner to ensure

proper ﬂame appearance.

Step 12. (Page 27) Attach Safety-in-Operation

Warnings.

DETAILED INSTALLATION STEPS

Step 1. FRAMING

Frame these appliances as illustrated in Figure

8 on Page 10, unless the appliance is to be

installed in a corner. See Figure 9 on Page 11

for corner framing installations. All framing

details must allow for a minimum clearance

to combustible framing members as shown in

Table 5 on Page 8.

If the appliance is to be elevated above oor

level, a solid continuous platform must be

constructed below the appliance.

Headers may be in direct contact with the ap-

pliance top spacers but must not be supported

by them or notched to t around them.

The replace should be secured to the side fram-

ing members using the unit nailing anges - one

top and bottom on each side of the replace front

(see Figure 7). Use 8d nails or their equivalent.

Unit Being Secured by Its Nailing

Flanges to the Framing

Note: The nailing flanges, combustible members

and screw heads located in areas directly adjacent

to the nailing flanges, are EXEMPT from the 1/2”.

clearance to combustible requirements for the

firebox outer wrapper. Combustible framing may be

in direct contact with the nailing flanges and may

be located closer than 1/2” from screw heads and

the firebox wrapper in areas adjacent to the nailing

flanges. Frame the opening to the exact dimensions

specified in the framing details of this manual.

Use Top Flange For

1/2” Thick Drywall

Use Bottom Flange For

5/8” Thick Drywall

Front Of

Fireplace

Use Center Flange

For Flush Mount

Left Side Front Corner of Fireplace Shown

(Right Side Requirements the Same)

Unit Being Secured By Its Nailing Flanges

To The Framing

NOTE: The nailing ﬂanges, combustible members

and screw heads located in areas directly adja-

cent to the nailing anges, are EXEMPT from the

1/2" clearance to combustible requirements for

the ﬁrebox outer wrapper. Combustible framing

may be in direct contact with the nailing ﬂanges

and may be located closer than 1/2" from screw

heads and the ﬁrebox wrapper in areas adjacent

to the nailing ﬂanges. Frame the opening to

the exact dimensions speciﬁed in the framing

details of this manual.

Left Side Front Corner of Fireplace Shown

(Right Side Requirements the Same).

Figure 7 - Unit Secured by Nailing

Flanges to the Framing

INNOVATIVE HEARTH PRODUCTS • POWER VENT DV GAS FIREPLACES (MontebelloDLX__TYN / MontebelloDLXCD__TYN) • INSTALLATION INSTRUCTIONS

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Vent Size

Co-axial DV

Vent Size

4-1/2" Inner

7-1/2" Outer

Top View

Front View

5-3/32” (129)

Right Side View

14-1/8”

8-1/2”

(216)

5-1/4”

(133)

(359) 26-15/32”

(672)

25-29/32”

(658)

25-1/2”

(648)

7”

2-1/2” (64)

(178)

19-5/8”

(498)

Gas Inlet

(This

Side

Only)

Electrical

Inlet

8-3/8”

(213)

8” / 11”

Vent / Intake

Notes

Diagrams, illustrations and photographs

are not to scale - consult installation

instructions. Product designs, materials,

dimensions, speciﬁcations, colors and

prices are subject to change or discon-

tinuance without notice.

* C = Adaptor Plus 4 ft Vertical Vent (min.) and 90° Elbow

Model

No. A B C D E F G H J

40 in. in. 50-5/8 37-1/4 42-7/8 25-5/16 34 37-5/8 33-3/32 29-9/32 34-3/4

mm 1286 946 1089 643 864 956 840 744 883

45 in. in. 56-11/16 42-1/4 47-7/8 28-3/8 40-1/8 43-5/8 38-3/32 34-1/2 40-59/64

mm 1440 1073 1216 721 1019 1108 968 876 1039

Figure 8 - Fireplace and Framing Specications

INNOVATIVE HEARTH PRODUCTS • POWER VENT DV GAS FIREPLACES (MontebelloDLX__TYN / MontebelloDLXCD__TYN) • INSTALLATION INSTRUCTIONS

FIREPLACE AND FRAMING SPECIFICATIONS

VENT FRAMING

TOP VENT WITH 2 FEET

VERTICAL VENT AND

ONE 90° ELBOW

Framing should be constructed

of 2x4 or larger lumber.

Inches (mm)

(641)

25-1/4”

1/2 A

10-1/2”

(267)

7”

(178)

5-1/8”

(130) 12-1/8”

(308)

PIPE CENTERLINE

Model No. A B C *

40 in. in. 50-3/4 43 139-1/8

mm 1289 1092 3534

45 in. in. 56-7/8 48 144-1/8

mm 1445 1219 3661

Adaptor Plus 4 ft

Vertical Vent

(min.) and 90°

Elbow

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Gas lines must be routed, constructed and made

of materials that are in strict accordance with

local codes and regulations. We recommend

hiring a qualied plumber or gas tter to cor-

rectly size and route the gas supply line to the

appliance. Installing a gas supply line from the

fuel supply to the appliance involves numerous

considerations of materials, protection, sizing,

locations, controls, pressure, sediment, and

more. Only a qualied installer should attempt

sizing or installing gas pipe.

NOTES:

• Allappliancesarefactory-equippedwitha

exiblegaslineconnectorand1/2"shutoff

valve (see Figure 30 on Page 21).

• SeeMassachusetts Requirements on Page

4foradditionalrequirementsforinstallations

inthestateofMassachusettsintheUSA.

• ThegassupplylineshouldNotbeconnected

totheapplianceuntilStep 6 (Page 21).

• Apipejointcompoundratedforgasshould

beusedonthethreadedjoints.Beverycareful

thatthepipecompounddoesnotgetinside

thepipe.

• Installing a sediment trap in the supply

lineascloseaspossibletotheapplianceis

recommended.

• Checkwithlocal building ofcialfor local

coderequirements.

Model No. A B C D

40 in. in. 50-5/8 83-5/8 59-1/8 41-7/8

mm 1286 2124 1502 1064

45 in. in. 56-3/4 89-7/8 63-1/2 44-7/8

mm 1441 2283 1613 1140

Back wall of chase/enclosure

(including any finishing materials)

Figure 9 - Corner Framing with Power Vent Termination

6-1/4”

(159 mm)

19-5/8”

(498 mm)

Figure 10 - Right-Front Corner of

Fireplace Framing

Step 2. ROUTING GAS LINE

Route a 1/2" (13 mm) gas line along the inside

of the right side framing as shown in Figure

10. Gas lines must be routed, constructed and

made of materials that are in strict accordance

with local codes and regulations.

All appliances are factory-equipped with a ex-

ible gas line connector and 1/2" shutoff valve.

(see Step 6 on Page 21).

Proper Sizing of Gas Line

Properly size and route the gas supply line from

the supply regulator to the area where the appli-

ance is to be installed per requirements outlined

in the (USA) National Fuel Gas Code, ANSI

Z223.1/NFPA 54 - latest edition, or (Canada)

CAN/CGA-B149.1 - latest edition.

Never use galvanized or plastic pipe. Refer to

Table 6 for proper sizing of the gas supply line,

if black iron pipe is being used.

Schedule 40 Black Iron Pipe

Inside Diameter

Length Inside Diameter

0 - 10 ft (0 - 3.1 m) 1/2" (12.7 mm)

10 - 40 ft (3.1 - 12.2 m) 1/2" (12.7 mm)

40 - 100 ft (12.2 - 30.5 m) 1/2" (12.7 mm)

100 - 150 ft (30.5 - 45.7 m) 3/4" (19.1 mm)

150 - 200 ft (45.7 - 61.0 m) 3/4" (19.1 mm)

Table 6

INNOVATIVE HEARTH PRODUCTS • POWER VENT DV GAS FIREPLACES (MontebelloDLX__TYN / MontebelloDLXCD__TYN) • INSTALLATION INSTRUCTIONS

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Power Vent Components

Locate the replace as instructed in this manual. Make the following modications to add the com-

ponents used with the Power Vent Kit. This kit may only be used in conjunction with Direct-Vent

series electronic versions of Innovative Hearth Products Fireplaces. This installation must conform

with local codes, or, in the absence of local codes, with the (USA) National Fuel Gas Code, ANSI

Z223.1/NFPA 54 - latest edition, or (Canada) CAN/CGA-B149.1 - latest edition.

CAUTION: This power vent kit cannot be used with millivolt appliances. Use the kit only with

the electronically controlled ﬁreplaces listed for its use as shown in this document.

Item No. Part

Number Description Qty.

1604187-01 Adaptor Assembly With Probe 1

2601970-01 Vacuum Hose 1

3601451-01 Termination Assembly 1

474L61 SV Termination Adaptor (SV4.5RCH) 1

5102010-01 Strain Relief - 3/8" 1

6H2246 Firestop Assembly (Horizontal) 1

7102022-01 Hose Clamp - 11/32" 2

8P-8-7102 Snap Bushing 1

9 - Ring Terminal - #10 2

10 - Insulated 1/4" Male Terminal 4

Step 3. INSTALL THE VENT SYSTEM

General Information

These instructions should be used as a guide-

line and do not supersede local codes in any

way. Install venting according to local codes,

these instructions, and the (USA) National

Fuel Gas Code, ANSI Z223.1/NFPA 54 - latest

edition, or (Canada) CAN/CGA-B149.1 - latest

edition.

These ﬁreplaces are designed, tested and

listed for operation and installation only

with Secure Vent® (SV4.5) and Secure Flex®

Direct-Vent System Components, manufac-

tured by Security Chimneys International.

These approved vent system components are

labeled for identiﬁcation. DO NOT use any

other manufacturer's vent components with

these appliances.

Ensure clearances are in accordance with

local installation codes and the requirements

of the gas supplier.

Dégagement conforme aux codes

d'installation locaux et aux exigences du

foumisseunde gaz.

Use only approved venting components. See

Approved Vent Components on Page 2.

These ﬁreplaces must be vented directly

to the outside.

The vent system may not service multiple

appliances, and must never be connected to a

ue serving a separate solid fuel burning ap-

pliance. The vent pipe is tested to be run inside

an enclosed wall (such as a chase). There is

no requirement for inspection openings in the

enclosing wall at any of the joints in the vent pipe.

Venting System

With the appliance secured in framing, de-

termine vent routing and identify the exterior

termination location. The following sections

describe horizontal (exterior wall) vent applica-

tions. A list of approved venting components

is shown on Page 28.

Figure 11 - Power Vent Kit Components

INNOVATIVE HEARTH PRODUCTS • POWER VENT DV GAS FIREPLACES (MontebelloDLX__TYN / MontebelloDLXCD__TYN) • INSTALLATION INSTRUCTIONS

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

NOTE: Convert inches into metric equivalent

measurement, as follows:

Millimeters (mm) = Inches x 25.4

Centimeters (cm) = Inches x 2.54

Meters (m) = Inches x .0254

Effective Vent Length

Model Effective Length

SV4.5L6 4-1/2"

SV4.5L12 10-1/2"

SV4.5L24 22-1/2"

SV4.5L36 34-1/2"

SV4.5L48 46-1/2"

Table 7

TRAHCHTGNELNOITCESTNEV

lanimoN htgneLnoitceS )sehcni( 6 21 42 63 84 T

noitceSteN )sehcni(htgneL 2/1-4 2/1-01 2/1-22 2/1-43 2/1-64

tneVfothgieH snoitceStneVforebmuN

sehcni tf

5.4 573.0 1 0 0 0 0 1

9 57.0 2 0 0 0 0 2

5.01 578.0 0 1 0 0 0 1

51 52.1 1 1 0 0 0 2

5.22 578.1 0 0 1 0 0 1

5.13 526.2 0 3 0 0 0 3

5.43 578.2 0 0 0 1 0 1

5.73 521.3 1 1 1 0 0 3

5.34 526.3 0 2 1 0 0 3

54 57.3 0 0 2 0 0 2

5.64 578.3 0 0 0 0 1 1

15 52.4 1 0 0 0 1 2

5.55 526.4 0 1 2 0 0 3

75 57.4 0 0 1 1 0 2

5.76 526.5 0 0 3 0 0 3

96 57

.5 0 0 0 2 0 2

5.37 521.6 1 0 0 2 0 3

5.97 526.6 0 1 0 2 0 3

18 57.6 0 0 0 1 1 2

5.19 526.7 0 0 2 0 1 3

39 57.7 0 0 0 0 2 2

5.79 521.8 1 0 0 0 2 3

5.301 526.8 0 0 0 3 0 3

801 9 1 0 0 3 0 4

711 57.9 1 0 5 0 0 6

5.811 578.9 1 1 0 3 0 5

621 5.01 0 0 1 3 0 4

5.031 578.01 1 0 1 3 0 5

531 52.11 0 0 6 0 0 6

5.931 526.11 0 0 0 0 3 3

5.241 578.11 1 0 0 4 0 5

441 21 1 0 0 0 3 4

5.451 578.21 1 1 0 0 3 5

5.061 573.31 0 2 0 0 3 5

5.271 573.41 0 0 0 5 0 5

771 57.41 1 0 0 5 0 6

681 5.51 0 0 0 0 4 4

5.691 573.61 0 1 0 0 4 5

702 52.71 0 0 0 6 0 6

5.112 526.71 1 0 0 6 0 7

5.712 521.81 0 1 0 6 0 7

5.922 521.91 0 0 1 6 0 7

5.23

2 573.91 0 0 0 0 5 5

5.142 521.02 0 0 0 7 0 7

642 5.02 1 0 0 7 0 8

252 12 0 1 0 7 0 8

TRAHCHTGNELNOITCESTNEV

lanimoN htgneLnoitceS )sehcni( 6 21 42 63 84 T

noitceSteN )sehcni(htgneL 2/1-4 2/1-01 2/1-22 2/1-43 2/1-64

tneVfothgieH snoitceStneVforebmuN

sehcni tf

5.4 573.0 1 0 0 0 0 1

9 57.0 2 0 0 0 0 2

5.01 578.0 0 1 0 0 0 1

51 52.1 1 1 0 0 0 2

5.22 578.1 0 0 1 0 0 1

5.13 526.2 0 3 0 0 0 3

5.43 578.2 0 0 0 1 0 1

5.73 521.3 1 1 1 0 0 3

5.34 526.3 0 2 1 0 0 3

54 57.3 0 0 2 0 0 2

5.64 578.3 0 0 0 0 1 1

15 52.4 1 0 0 0 1 2

5.55 526.4 0 1 2 0 0 3

75 57.4 0 0 1 1 0 2

5.76 526.5 0 0 3 0 0 3

96 57

.5 0 0 0 2 0 2

5.37 521.6 1 0 0 2 0 3

5.97 526.6 0 1 0 2 0 3

18 57.6 0 0 0 1 1 2

5.19 526.7 0 0 2 0 1 3

39 57.7 0 0 0 0 2 2

5.79 521.8 1 0 0 0 2 3

5.301 526.8 0 0 0 3 0 3

801 9 1 0 0 3 0 4

711 57.9 1 0 5 0 0 6

5.811 578.9 1 1 0 3 0 5

621 5.01 0 0 1 3 0 4

5.031 578.01 1 0 1 3 0 5

531 52.11 0 0 6 0 0 6

5.931 526.11 0 0 0 0 3 3

5.241 578.11 1 0 0 4 0 5

441 21 1 0 0 0 3 4

5.451 578.21 1 1 0 0 3 5

5.061 573.31 0 2 0 0 3 5

5.271 573.41 0 0 0 5 0 5

771 57.41 1 0 0 5 0 6

681 5.51 0 0 0 0 4 4

5.691 573.61 0 1 0 0 4 5

702 52.71 0 0 0 6 0 6

5.112 526.71 1 0 0 6 0 7

5.712 521.81 0 1 0 6 0 7

5.922 521.91 0 0 1 6 0 7

5.23

2 573.91 0 0 0 0 5 5

5.142 521.02 0 0 0 7 0 7

642 5.02 1 0 0 7 0 8

252 12 0 1 0 7 0 8

TRAHCHTGNELNOITCESTNEV

lanimoN htgneLnoitceS )sehcni( 6 21 42 63 84 T

noitceSteN )sehcni(htgneL 2/1-4 2/1-01 2/1-22 2/1-43 2/1-64

tneVfothgieH snoitceStneVforebmuN

sehcni tf

672 32 0 0 0 8 0 8

972 52.32 0 0 0 0 6 6

5.082 573.32 1 0 0 8 0 9

5.982 521.42 0 1 0 0 6 7

5.103 521.52 0 0 1 0 6 7

5.013 578.52 0 0 0 9 0 9

5.523 521.72 0 0 0 0 7 7

033 5.72 1 0 0 0 7 8

543 57.82 0 0 0 01 0 01

5.943 521.92 1 0 0 01 0 11

273 13 0 0 0 0 8 8

5.973 526.13 0 0 0 11 0 11

5.814 578.43 0 0 0 0 9 9

564 57.83 0 0 0 0 01 01

5.574 526.93 0 1 0 0 01 11

084 04 1 1 0 0 01 11

294 14 1 0 1 0 01 21

5.994 526.14 0 0 0 1 01 11

405 24 1 0 0 1 01 21

5.115 526.24 0 0 0 0 11 11

5.025 573.34 0 2 0 1 11 41

135 52.44 0 2 2 0 11 51

5.835 578.44 1 0 0 2 11 41

945 57.54 1 0 2 1 11 51

855 5.64 0 0 0 0 21 21

5.265 578.64 1 0 0 0 21 31

5.865 573.74 0 1 0 0 21 31

375 57.74 1 1 0 0 21 41

5.085 573.84 0 0 1 0 21 31

5.985 521.94 0 1 2 2 01 51

5.595 526.94 1 1 1 0 21 51

5.406 573.05 0 0 0 0 31 31

516 52.15 0 1 0 0 31 41

5.526 521.25 0 2 0 0 31 51

5.136 526.25 1 0 1 0 31 51

5.736 521.35 0 1 1 0 31 51

156 52.45 0 0 0 0 41 41

5.556 526.45 1 0 0 0 41 51

276 65 0 2 0 0 41 61

876 5.65 1 0 1 0 41 61

5.886 573.75 1 1 1 0 41 71

5.796 521.85 0 0 0 0 51 51

207 5.85 1 0 0 0 51 61

5.217 573.95 1 1 0 0 51 71

027 06 0 0 1 0 51 61

TRAHCHTGNELNOITCESTNEV

lanimoN htgneLnoitceS )sehcni( 6 21 42 63 84 T

noitceSteN )sehcni(htgneL 2/1-4 2/1-01 2/1-22 2/1-43 2/1-64

tneVfothgieH snoitceStneVforebmuN

sehcni tf

672 32 0 0 0 8 0 8

972 52.32 0 0 0 0 6 6

5.082 573.32 1 0 0 8 0 9

5.982 521.42 0 1 0 0 6 7

5.103 521.52 0 0 1 0 6 7

5.013 578.52 0 0 0 9 0 9

5.523 521.72 0 0 0 0 7 7

033 5.72 1 0 0 0 7 8

543 57.82 0 0 0 01 0 01

5.943 521.92 1 0 0 01 0 11

273 13 0 0 0 0 8 8

5.973 526.13 0 0 0 11 0 11

5.814 578.43 0 0 0 0 9 9

564 57.83 0 0 0 0 01 01

5.574 526.93 0 1 0 0 01 11

084 04 1 1 0 0 01 11

294 14 1 0 1 0 01 21

5.994 526.14 0 0 0 1 01 11

405 24 1 0 0 1 01 21

5.115 526.24 0 0 0 0 11 11

5.025 573.34 0 2 0 1 11 41

135 52.44 0 2 2 0 11 51

5.835 578.44 1 0 0 2 11 41

945 57.54 1 0 2 1 11 51

855 5.64 0 0 0 0 21 21

5.265 578.64 1 0 0 0 21 31

5.865 573.74 0 1 0 0 21 31

375 57.74 1 1 0 0 21 41

5.085 573.84 0 0 1 0 21 31

5.985 521.94 0 1 2 2 01 51

5.595 526.94 1 1 1 0 21 51

5.406 573.05 0 0 0 0 31 31

516 52.15 0 1 0 0 31 41

5.526 521.25 0 2 0 0 31 51

5.136 526.25 1 0 1 0 31 51

5.736 521.35 0 1 1 0 31 51

156 52.45 0 0 0 0 41 41

5.556 526.45 1 0 0 0 41 51

276 65 0 2 0 0 41 61

876 5.65 1 0 1 0 41 61

5.886 573.75 1 1 1 0 41 71

5.796 521.85 0 0 0 0 51 51

207 5.85 1 0 0 0 51 61

5.217 573.95 1 1 0 0 51 71

027 06 0 0 1 0 51 61

Table 8 - Vent Section Length

INNOVATIVE HEARTH PRODUCTS • POWER VENT DV GAS FIREPLACES (MontebelloDLX__TYN / MontebelloDLXCD__TYN) • INSTALLATION INSTRUCTIONS

VENT SECTION LENGTHS

Determine the number of straight vent sections

required. 4-1/2" (114 mm), 10-1/2" (267 mm),

22-1/2" (572 mm), 34-1/2". (876 mm) and 46-

1/2" (1181 mm) net section lengths are available

(see Tables 7 and 8).

Offset Installation

Analyze the vent routing and determine the

quantities of vent sections and number of

elbows required. Refer to Figures 16 and 17

on Page 15 showing vent run requirements to

aid in selecting the type of vertical installation

desired. Vent sections are available in net lengths

of 4-1/2" (114 mm), 10-1/2" (267 mm), 22-1/2"

(572 mm), 34-1/2" (876 mm) and 46-1/2" (1181

mm). Refer to the Vent Section Length Chart for

an aid in selecting length combinations. Elbows

are available in 90° and 45° congurations. Refer

to Figure 15 on Page 14 for the SV4.5 E45 and

SV4.5 E90 elbow dimensional specications.

Where required, a telescopic vent section

(SV4.5LA) may be used to provide the installer

with an option in installing in tight and conned

spaces or where the vent run made up of xed

length pieces develops a joint in a undesirable

location, or will not build up to the required

length. The SV4.5LA Telescopic Vent Section

has an effective length of from 1-1/2" (38 mm)

to 6-3/4" (171 mm). The SV4.5LA is tted with a

dimpled end (identical to a normal vent section

component) and a plain end with 3 pilot holes.

Slip the dimpled end over the locking channel

end of a standard SV4.5 vent component the

required distance and secure with three screws.

Maintain a minimum 1" (25 mm) clearance

to combustible materials for all vertical ele-

ments. Clearances for all horizontal elements

are 3" (76 mm) on top, 1" (25 mm) on sides

and 1" (25 mm) on the bottom.

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Figure 12 - Framing Ceiling Opening

A. Frame ceiling opening - Use a plumb line

from the ceiling above the appliance to locate

center of the vertical run. Cut and/or frame

an opening, 10-1/2" x 10-1/2" (267 mm x 267

mm) inside dimensions, about this center mark

(Figure 12).

Figure 13 - Attaching the Vent Adaptor

Align the dimple (four places) of the

upper vent section with the opening

of the locking incline channel on

the lower vent section or appliance

collar. Twist vent component

clockwise to engage and seal until

arrow and dimple align.

Dimple

Locking Incline

Channel

Connected Vent

Sections Arrow

Arrow

Adaptor on Appliance Collar

or Vent Section

B. Attach adaptor (with probe) to appliance

collar - Secure Vent® SV4.5 direct-vent sys-

tem components are unitized concentric pipe

components featuring positive twist lock con-

nections (see Figure 13).

All of the appliances covered in this document

are tted with collars having locking inclined

channels. The dimpled end of the adaptor ts

over the appliance collar to create the positive

twist lock connection.

10-1/2" min.

(267 mm)

Ceiling Framing

Plumb Bob

10-1/2" min.

(267 mm)

To attach a vent component to the adaptor on

appliance collar, align the dimpled end over the

adaptor collar, adjusting the radial alignment

until the four locking dimples are aligned with the

inlet of the four inclined channels on the collar

(refer to Figure 13). Push the vent component

against the collar until it fully engages, then twist

the component clockwise, running the dimples

down and along the incline channels until they

seat at the end of the channels.

Support the vertical portion of the venting

system every eight feet (2.4 m) above the

ﬁreplace vent outlet. One method of support

is by utilizing eld provided support straps

(conventional plumber's tape). Secure the

plumber's tape to the framing members with

nails or screws. Strap the tape around the vent,

securing the ends of the tape to the framing.

If desired, sheet metal screws #6 x 1/2" length

may be used to secure the support straps to

the vent pipe.

F. Change vent direction to horizontal/inclined

run - At transition from or to a horizontal/in-

clined run, install the SV4.5E45 and SV4.5E90

elbows in the same manner as the straight vent

sections. The elbows feature a twist section to

allow them to be routed about the center axis

of their initial collar section to align with the

required direction of the next vent run element.

Twist elbow sections in a clockwise direction

only so as to avoid the possibility of unlocking

any of the previously connected vent sections

(see Figures 13 and 15).

The unitized design of the Secure Vent® com-

ponents will engage and seal both the inner and

outer pipe without the need for sealant or screws.

If desired a #6 x 1/2" screw may be used at the

joint, but it is not required as the pipe will securely

lock when twisted.

C. Attach vent components to each other - Other

vent sections may be added to the previously

installed section in accordance with the require-

ments shown in Figures 16 and 17 on Page 15.

To add another vent component to a length of

vent run, align the dimpled end over the inclined

channel end of the previously installed section,

adjusting the radial alignment until the four

locking dimples are aligned with the inlets of

the four incline channels of the previous section.

Push the vent component against the previ-

ous section until it fully engages, then twist

the component clockwise running the dimples

down and along the incline channels until they

seat at the end of the channels. This seating

position is indicated by the alignment of the

arrow and dimple as shown in Figure 13.

D. Install ﬁrestop/spacer at ceiling - When

using Secure Vent, use SV4.5VF restop/spacer

at ceiling joists. If there is living space above

the ceiling level, the restop/spacer must be

installed on the bottom side of the ceiling. If

attic space is above the ceiling, the restop/

spacer must be installed on the top side of

the joist. Route the vent sections through the

framed opening and secure the restop/spacer

with 8d nails or other appropriate fasteners at

each corner.

Maintain 1" (25 mm) clearance to combus-

tibles, framing members, and attic or ceiling

insulation when running vertical chimney

sections. Attic insulation shield (H3907) may

be used to obtain the required clearances

indicated here. See installation accessories

on Page 28. The gap between the vent pipe

and a vertical ﬁrestop may be sealed with

noncombustible caulking.

E. Support the vertical vent run sections -

8-1/8”

(206 mm)

4-13/16”

(122 mm)

Swivel Joint

(360° swivel)

SV4.5E45

45° Elbow)

Swivel Joint

(360° swivel)

SV4.5E90

90° Elbow)

G. Continue installation of horizontal/inclined

sections - Continue with the installation of the

straight vent sections in horizontal/inclined run

as described in Step C. Install support straps

every three feet (914 mm) along horizontal/

inclined vent runs using conventional plumber’s

tape (Figure 16 on Page 15).

NOTE: Maintain the horizontal/inclined run in

a straight, slightly elevated plane - approxi-

mately 1/4" per foot (20 mm per meter) - in

a direction away from the ﬁreplace. Smaller

rise per foot run ratios are acceptable, down

to at or near level. Use a carpenter’s level to

measure from a constant surface and adjust

the support straps as necessary.

NOTE: Maintain the required clearances to

combustibles: 1" (25 mm) at all sides for all

vertical runs; and 3" (76 mm) at the top, 1" (25

mm) at sides, and 1" (25 mm) at the bottom

for all horizontal/inclined runs.

Blocking

Support Straps

(Plumber's

tape)

8' (2.4 m)

Maximum

1/2" (13 mm)

minimum

clearance to

combustibles

Figure 14 - Supporting Vertical Vents

Figure 15 - Vent Elbow Sections

INNOVATIVE HEARTH PRODUCTS • POWER VENT DV GAS FIREPLACES (MontebelloDLX__TYN / MontebelloDLXCD__TYN) • INSTALLATION INSTRUCTIONS

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Power Vent

Termination

Horizontal / Inclined Run Support

Brackets Building

Support

Framing

SV4.5E90

Elbow

Ceiling

Minimum

Vent Run

Horizontal

10 ft

Exterior

Wall

Power Vent

Termination

Probe Adaptor

(required)

Probe Adaptor

(required)

Fireplace

Floor

Maximum Horizontal

Venting 110 ft

Up to 6 Elbows

Firestop / Spacer

Exterior

Wall

SV4.5L 6 / 12 / 24 / 36 / 48

Vent Sections Vertical Rise

66 ft max.

4 ft min.

Figure 16 - Typical Power Vent Routing

Venting Can Run Up To

3 ft Below Unit

VENT FIGURES

NOTES:

• SecureVent®components(rigidventpipeandterminal)areshown.

• Two45°elbowsmaybeusedinplaceofone90°elbow.

• SV4.5VF(SecureVent)restop/spacermustbeusedanytimeventpipepassesthroughacombustibleoororceiling.SV4.5HF(SecureVent)

restop/spacermustbeusedanytimeventpipepassesthroughacombustiblewall.

• Maintain the horizontal/inclined run in a straight, slightly elevated plane - approximately 1/4" per foot (20 mm per meter) - in a direction

away from the ﬁreplace. Smaller rise per foot run ratios are acceptable, down to at or near level. Use a carpenter’s level to measure from a

constant surface and adjust the support straps as necessary.

INNOVATIVE HEARTH PRODUCTS • POWER VENT DV GAS FIREPLACES (MontebelloDLX__TYN / MontebelloDLXCD__TYN) • INSTALLATION INSTRUCTIONS

Power Venting

Maximum Number Of Elbows - 6

Maximum Feet Of Run A + B 110 ft

Minimum Horizontal Run B 10 ft

Minimum Vertical Run A Adaptor Plus 4 ft Vertical Vent

(min.) and 90° Elbow

Maximum Vertical Rise A 66 ft

Table 9

Minimum Clearance to Combustibles

Vertical Vent Pipe 1.0" (25.4 mm)

Horizontal Vent Pipe

Top - 3" (76.2 mm)

Sides - 1" (25.4 mm)

Bottom - 1" (25.4 mm)

Table 10

Probe Adaptor

(Required)

(See Chart)

Figure 17 - Power Vent Routing with Probe Adaptor

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

INNOVATIVE HEARTH PRODUCTS • POWER VENT DV GAS FIREPLACES (MontebelloDLX__TYN / MontebelloDLXCD__TYN) • INSTALLATION INSTRUCTIONS

D. Attach vent components to appliance - To

attach a vent component to the appliance

collar, align the dimpled end over the collar,

adjusting the radial alignment until the four

locking dimples are aligned with the inlets of

the four incline channels on the collar (refer

to Figure 13 on Page 14).

Push the vent component against the collar

until it fully engages, then twist the component

clockwise, running the dimples down and along

the incline channels until they seat at the end of

the channels. The unitized design of the Secure

Vent components will engage and seal both the

inner and outer pipe elements with the same

procedure. Sealant and securing screws are

not required.

E. Attach vent components to each other -

Other vent sections may be added to the

previously installed section in accordance

with the requirements of the vent tables.

To add another vent component to a length

of vent run, align the dimpled end of the

component over the inclined channel end

of the previously installed section, adjusting

the radial alignment until the four locking

dimples are aligned with the inlets of the four

incline channels of the previous section. Push

the vent component against the previous

section until it fully engages, then twist the

component clockwise running the dimples

down and along the incline channels until they

seat at the end of the channels. This seating

position is indicated by the alignment of

the arrow and dimple as shown in Figure

13 on Page 14.

F. Install ﬁrestop/spacer at ceiling -

When using Secure Vent, use SV4.5VF re-

stop/spacer at ceiling joists. If there is living

space above the ceiling level, the restop/

spacer must be installed on the bottom side

of the ceiling. If attic space is above the ceil-

ing, the restop/ spacer must be installed

on the top side of the joist. Route the vent

sections through the framed opening and

secure the restop/spacer with 8d nails or

other appropriate fasteners at each corner.

The gap between the vent pipe and a restop

can be sealed with noncombustible caulking.

Maintain 1" (25 mm) clearance to com-

bustibles, framing members, and attic or

ceiling insulation when running vertical

chimney sections.

G. Support the vertical run sections -

On the vertical run, support the venting system

every eight feet (2.4 m) above the replace

vent outlet with eld provided support straps

(Plumber's tape). Attach the straps to the vent

pipe and secure to the framing members with

nails or screws.

H. Change vent direction - At transitions from

or to a horizontal/inclined run, install the

SV4.5E45 and SV4.5E90 elbows in the same

manner as the straight vent sections. The

elbows feature a twist section to allow them

to be routed about the center axis of their

initial collar section to align with the required

direction of the next vent run element. Twist

elbow sections in a clockwise direction only

so as to avoid the possibility of unlocking

any of the previously connected vent sec-

tions (see Figure 13 on Page 14).

I. Continue installation of horizontal/inclined

sections - Continue with the installation

of the straight vent sections in horizontal/

inclined run as described in Step E. Install

support straps every three feet (1914 mm)

along horizontal/inclined vent runs using

conventional plumber’s tape (see Figure 16

on Page 15).

NOTE: Maintain the horizontal/inclined

run in a straight, slightly elevated plane

- approximately 1/4" per foot (20 mm

per meter) - in a direction away from the

ﬁreplace. Smaller rise per foot run ratios

are acceptable, down to at or near level.

Use a carpenter’s level to measure from

a constant surface and adjust the support

straps as necessary.

Installing Power Vent Termination

J. Assemble vent run to exterior wall - If not

previously measured, locate the center of

the vent on the exterior wall. Prepare an

opening as described in this manual. As-

semble the vent system to a point where

the terminus of the last section is within 8"

of the outside wall surface where the power

vent is to be mounted (see Figure 18 on

Page 17).

If the terminus of the last section is not

within this distance, use the telescopic

vent section SV4.5LA, as the last vent

section. For wall thicknesses greater than

that shown in Figure 19 on Page 17, refer

to Table 11 on Page 17 for the additional

venting components needed (in addition to

the termination and adaptor) for a particular

range of wall thicknesses.

K. Attach termination adaptor - Attach the

adaptor (SV4.5RCH - provided with the power

vent kit) to the vent section telescoping vent

section, or elbow, as shown in Figures 18

and 19 on Page 17 in the same manner as

any SV4.5 vent component.

HORIZONTAL (OUTSIDE WALL)

TERMINATION SYSTEM

See Figures 16 and 17 on Page 15 illustrating

the various horizontal venting congurations

that are possible for use with these appliances.

Table 9 on Page 15 shows each system’s

minimum and maximum vertical and horizontal

length values that can be used to design and

install the vent components in a variety of

applications.

The horizontal vent system terminates through

an outside wall. Building codes limit or prohibit

terminating in specic areas. Refer to Figure 4

on Page 7 for location guidelines.

Secure Vent® SV4.5 direct-vent system compo-

nents are unitized concentric pipe components

featuring positive twist lock connection, (refer

to Figure 13 on Page 14). All of the appliances

covered in this document are tted with collars

having locking inclined channels. The dimpled

end of the vent components t over the appliance

collar to create the positive twist lock connection.

A. Plan the vent run -

Analyze the vent routing and determine the

types and quantities of sections required

4-1/2" (114 mm), 10-1/2" (267 mm), 22-1/2"

(572 mm), 34-1/2" (876 mm) and 46-1/2"

(1181 mm) net section lengths are available.

Make allowances for elbows as indicated in

Figure 15 on Page 14.

Maintain a minimum 1" (25 mm) clearance

to combustibles on the vertical sections.

Clearances for the horizontal runs are: 3"

(76 mm) on top, 1". (25 mm) on sides, and

1" (25 mm) at the bottom.

B. Frame exterior wall opening -

Locate the center of the vent outlet on the

exterior wall according to the dimensions

shown in Figure 8 on Page 10.

Cut and/or frame an opening, 10-1/2" x 12-

1/8" (267 mm x 308 mm) inside dimensions,

about this center.

C. Frame ceiling opening - If the vertical route

is to penetrate a ceiling, use a plumb line to

locate the center above the appliance. Cut

and/or frame an opening, 10-1/2" x 10-1/2"

(267 mm x 267 mm) inside dimensions,

about this center (see Figure 12 on Page

14).

L. Install Firestop/Spacer at exterior wall -

Install SV4.5HF Firestop/Spacer, provided

with the power vent kit, over the opening at

the exterior side of the framing, long side

up, with the 3" spacer clearance at the top as

shown in Figure 18, and nail into place. The

Firestop/Spacer may also be installed over

the opening at the interior side of the fram-

ing. The gap between the vent pipe and a

restop can be sealed with noncombustible

caulking.

(The Firestop/Spacer may also be installed

over the opening at the interior side of the

framing).

M. Install the Power Vent termination - From

outside the exterior wall, slide the collars of

the termination onto the adaptor until the

termination seats against the exterior wall

surface to which it will be attached. Orient

the housing of the termination with the

arrow pointed upwards. Secure the termi-

nation to the exterior wall. The termination

must not be recessed into the exterior wall

or siding by more that the 1-1/4" (32 mm)

as shown in Figure 19.

Siding

Stucco

1-1/4” (32 mm) Maximum

Recess of the Square

Termination into Exterior

Finishing Material

Exterior Surface of

Framing

6” to 9-1/4”

(152 to 235 mm)**

Exterior Surface of Siding

Interior Surface of

Finished Wall

Maximum wall thickness

9-1/4” (235 mm)**

Power Vent

Termination

Maximum Extent of Vent Run

Sections Relative to Exterior

Surface of Framing

Last Vent Section.

Use Telescopic Vent

Section (SV4.5LA),

If Necessary

Adaptor

SV4.5RCH

*Use silicone caulking to

seal the top and sides of

the termination, up to the

underlayment, stucco, or

masonry wall surface.

Power Vent

Termination

*Caulk

To help minimize water infiltration

it is recommended that the Firestop/Spacer (SV4.5HF)

be installed on the exterior side of the wall.

Power Vent

Termination

7”

(178 mm)

5-1/8”

(130 mm)

12-1/8”

(308 mm)

NOTE: Centerline of Vent Piping is NOT

the Same as the Centerline of the

Frame Opening.

6” to 48” Vent Section,

Telescopic vent section,

Elbow or Appliance Collar Base of Appliance

3”

(76 mm)

1”

(25.4 mm)

Adaptor

SV4.5RCH

10-1/2”

(267 mm)

The Power Vent termination has been

designed to perform in a wide range of

weather conditions. Terminations meet

or exceed industry standards.

When selecting the location of termination,

do not place the termination where water

from eaves and adjoining roof lines may

create a heavy ﬂow of cascading water onto

the termination. If the termination must be

placed where the possibility of cascading

water exists, it is the responsibility of the

builder to direct the water away from the

termination cap by using gutters or other

means.

Carefully follow the Installation Instruc-

tions for the termination, including the

use of silicone caulking where required.

See Table 11 as an aid in venting component

selection for a particular range of exterior

wall thicknesses.

WARNING: The vent termination is hot

while in operation and for a period of

time following the use of the ﬁreplace.

Young children should be carefully su-

pervised when in the same area as a hot

termination.

Figure 18 - Installing Power Vent Horizontal Termination

Figure 19 - Venting Connection and Exterior Wall Recessing of the Power Vent

Horizontal Termination

Venting Components Required for Various Exterior Wall Thicknesses

when Using the Power Vent Termination

Vent Components Required Exterior Wall Thickness

Termination Kit Only 6 to 9-1/4" (152 to 235 mm)

Termination Kit and 6" Vent Section (SV4.5L6) 10-3/4 to 14" (273 to 356 mm)

Termination Kit and 12" Vent Section (SV4.5L12) 16-3/4 to 20" (426 to 508 mm)

Termination Kit and Telescopic Section (SV4.5L12) 11-3/4 to 20" (299 to 508 mm)

Table 11

See Figure 8 on Page 10 for Minimum

Distance to Base of Appliance

INNOVATIVE HEARTH PRODUCTS • POWER VENT DV GAS FIREPLACES (MontebelloDLX__TYN / MontebelloDLXCD__TYN) • INSTALLATION INSTRUCTIONS

**For thicknesses greater

than 9-1/4", see Table 11

Step 4. FIELD WIRING

CAUTION: Label all wires prior to disconnection when servic-

ing controls. Wiring errors can cause improper and dangerous

operation.

ATTENTION: Au moment de l'entretien des commandes,

étiquetez tous les ﬁls avant de les débrancher. Des erreurs

de cáblage peuvent entraîner un fonctionnement inadéquat

et dangereux.

Verify proper operation after servicing.

S'assurer que l'appareil fonctionne adéquatement une fois

l'entretien terminé.

CAUTION: Ground supply lead must be connected to the wire

attached to the green ground screw located on the outlet box.

See Figures 27 and 28 on Page 20. Failure to do so will result

in a potential safety hazard. The appliance must be electrically

grounded in accordance with local codes or, in the absence of

local codes, the (USA) National Electrical Code, ANSI/NFPA

70 - latest edition, or the Canadian Electrical Code, CSA C22.1

- latest edition.

Route Cable

NOTE: Electrical wiring must be performed by a qualiﬁed electrician.

• Install the strain relief in the hole provided on the right side of replace

for the electrical wiring (see Figure 20).

• Either use the intgrated junction box, or position an electrical junction

box (not provided) within reach of the termination wiring pigtail (see

Figure 23 on Page 19). Route the pigtail to the junction box as the

termination is installed.

• Route 14 gage AWG grounded solid wire Romex® or equally-sized

stranded cable (e.g., SJOT) from the replace to the newly installed

junction box near the termination. Ensure the cable is safety plated to

prevent damage from framing nails and nish drywall screws. Route

it into the lower control compartment and cut to length before install-

ing the terminals. Install provided hardware on the ends of the cable.

Cable is not provided. The provided crimp terminals are intended for

use with stranded cable. If using Romex, connect per National Electric

Code or local code.

14 Gage

Grounded

Romex or

similar

Stranded

Cable

Strain

Relief

Vacuum

Hose

Snap

Bushing

Wall Switch

Harness

Junction Box

Right Side

of Fireplace

Probe (1 *)

Hose Clamp (7 *)

Vacuum Hose (2 *)

* See Figure 11 on Page 12

Adaptor Assembly

Pressure Switch

Vacuum Hose

Firebox

Pressure switch is located

behind the panel on the right

side of ﬁrebox

Vacuum Hose

• Refer to Figure 25 on Page 19 and install the electrical hardware on

the ends of the cable. Male terminals on the Black and White wires,

and ring terminals on the ground wire.

• Using standard electrical practices and the terminals provided, con-

nect the three wires of the cable to the termination pigtail within the

Electrical junction box. Ensure ground.

• The replace end of the cable will be addressed in Connecting The

Power Vent To The Fireplace Control System.

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Figure 20 - Routing Wiring

Figure 21 - Vacuum Hose Connection to Probe

Figure 22 - Vacuum Hose Connection to Pressure Switch

NOTE: Pressure switch style may vary from that shown.

INNOVATIVE HEARTH PRODUCTS • POWER VENT DV GAS FIREPLACES (MontebelloDLX__TYN / MontebelloDLXCD__TYN) • INSTALLATION INSTRUCTIONS

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Wiring - Fireplace (See Figures 27 and 28 on Page 20)

NOTE: These electronic appliances must be connected to the main

power supply. The gas valve is set in place and pre-wired at the factory.

1. Route a 3-wire 120 Vac 60 Hz 1ph power supply to the appliance

junction box.

2. Remove the electrical inlet cover plate from the side of the unit by remov-

ing the plate securing screws (see Figure 8 on Page 10).

3. Remove the cover plate knockout and then feed the power supply through

the knockout opening and into the unit junction box.

4. Connect the black power supply to the power outlet red pigtail lead and

the white power supply to the common terminal of the outlet as shown in

Figures 27 and 28 on Page 20.

5. Connect the ground supply to the pigtail lead attached to outlet

green ground screw.

6. Wall-mounted ON/REMOTE/OFF burner control switch and remote

control kits may be used. Mount the switch in a convenient location

on a wall near the replace.

NOTE: One end of the supplied wire (15 ft) is factory-connected and

the other end is attached to the side of the unit.

CAUTION: Do Not connect the ON/REMOTE/OFF wall switch to a 120

V power supply.

8. Turn the wall-mounted ON/REMOTE/OFF burner control switch to the

OFF position.

9. After the wiring is complete, replace the cover plate.

Wiring - Power Vent Termination

Alternate Instructions (For use when access to the termination is easy

and a secondary electrical junction box installation is not desired).

• Remove the junction box cover from the termination by removing the

attaching screw (see Figure 23).

• Loosen the strain relief on the termination shown in Figure 25. Pull

the pigtail in and shorten it to t within the junction box cover.

WARNING: Crimp connectors may be used on stranded cables (such as

SJOT cable) only. Solid wire Romex must be connected per the National

Electric Code, NEC 70 - latest version, or local codes.

• Route 14 gage AWG grounded solid wire Romex or equally sized

stranded cable (e.g., SJOT) from the replace to the newly installed

junction box near the termination. Ensure the cable is safety plated to

prevent damage from framing nails and nish drywall screws. Route

it into the lower control compartment and cut to length before install-

ing the terminals. Install provided hardware on the ends of the cable.

Cable is not provided. The provided crimp terminals are intended for

use with stranded cable. If using Romex, connect per National Electric

Code or local code.

Attaching Screw

Pigtail Junction Box Cover

Cable

Black and White

Ground Wire

Strain Relief

Ground Cable to

The Termination

Pigtail Wires Cut

Off and Shortened

Wire Nuts

Strain Relief Holding Cable

• Refer to Figure 26 and install the electrical hardware on the replace

end of the cable. Male terminals (#10) on the Black and White wires,

and ring terminals (#9) on the ground. The termination end of the cable

will be connected to the termination with wire nuts (not provided).

• Refer to Figure 26 to connect the three wires of the cable to the termina-

tion. Ensure the ground ring terminal is grounded beneath a structural

screw as shown. Attach the junction box cover to the termination with

the screw previously removed.

• The replace end of the cable will be addressed in Connecting The

Power Vent To The Fireplace Control System.

Cable

Figure 23 - Bottom of Termination

Figure 24 - Cable Connections

Figure 25 - Back of Termination

Figure 26 - Junction Box Cover Removed

INNOVATIVE HEARTH PRODUCTS • POWER VENT DV GAS FIREPLACES (MontebelloDLX__TYN / MontebelloDLXCD__TYN) • INSTALLATION INSTRUCTIONS

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Step 5. REMOVE THE GLASS DOOR

ASSEMBLY

Refer to Figure 40 on Page 24 and remove the

front glass door assembly as follows:

To remove the rescreens, lift up the center of

the rod to disengage it from the center bracket,

bend down at center, hold left side with hand

until it disengages from left side, being careful

not to scratch the paint. Slowly remove the rod

from the right side.

Using a Phillips screwdriver, unfasten the two

(2) screws located at the top of the glass door

assembly.

Tilt the glass door assembly at the top away

from the unit. Lift it carefully off the bottom

door track and set the glass door assembly

aside, protecting it from inadvertent damage.

WARNING

• Handle this glass with extreme

care! Glass is susceptible to

damage - Do not scratch or

handle roughly.

• Do not attempt to substitute the

materials used on this door,

or replace cracked or broken

glass with any materials other

than those provided by the

appliance manufacturer.

• The glass door of this appliance

must only be replaced as a

complete unit as provided

by the manufacturer. Do not

attempt to replace broken,

cracked, or chipped glass

separately.

INNOVATIVE HEARTH PRODUCTS • POWER VENT DV GAS FIREPLACES (MontebelloDLX__TYN / MontebelloDLXCD__TYN) • INSTALLATION INSTRUCTIONS

Factory Wired

Field Wired

Junction Box

Tab Intact

Tab

Intact

n e e r G - d n u o r G

e t i h W - l a r

u e N

120 VAC - Black

Green

Ground

Screw

White

Green

Neutral

Side

Hot

Side

Red

Black

Figure 28 - Junction Box Wiring -

120 V, 60 hz, 1-phase

Figure 27 - Electronic Wiring Diagram

580489-01

Pilot Tube

Spark

Electrode

Flame

Sensor

IPI Pilot

885 Valve

Optional

Split Flow

Battery Holder w/Switch

ON/ Remote

/OFF

Battery Holder

Wire Harness

Reset Switch

(See instructions.)

Power Vent Blower

Power Vent

Models Only

Air Pressure Switch

Power Vent Only

Note: On models

without pressure

switch, these

connectors are

plugged together.

Main Wire

Harness

Main Power Cord

Control Module

Fuse

ELECTRONIC WIRING DIAGRAM

Ground Y

Battery Holder with Switch

ON/Remote/OFF

(Schematic representation only)

COLOR CODE:

B = Black

BB = Brown w/Black Stripe

BG = Brown w/Green Stripe

BL = Blue

BR = Brown

G = Green

GY = Gray

O = Orange

R = Red

W = White

Y = Yellow

La page est en cours de chargement...

Superior Fireplaces Signature DRT6340TYN Guide d'installation

Marque: Superior Fireplaces

Modèle: Signature DRT6340TYN

Catégorie: Cheminées

Taper: Guide d'installation

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Superior Fireplaces Signature DRT6340TYN Installation guide

Superior Fireplaces Signature DRT6340TYN Guide d'installation

Ce manuel convient également à

Superior Fireplaces Signature DRT6340TYN Guide d'installation

dans d''autres langues

Documents connexes

Autres documents