NewAge Products 66982 Mode d'emploi

INSTALLATION AND OPERATION GUIDE

ATTENTION: Is your Grill damaged?

Need help or spare parts? For fastest service,

contact NewAge Products at 1-877-306-8930;

or suppor[email protected]om.

Do not return to the retailer.

STOP

Use two or more people to move, assemble, or install the grill to avoid back

injury. Do not leave children unattended near the grill or cabinets.

THIS INSTRUCTION MANUAL CONTAINS IMPORTANT INFORMATION NECESSARY FOR THE PROPER ASSEMBLY AND SAFE USE OF

THE APPLIANCE.

READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS BEFORE ASSEMBLING AND USING THE APPLIANCE.

FOLLOW ALL WARNINGS AND INSTRUCTIONS WHEN USING THE APPLIANCE. FAILURE TO OPERATE THIS PRODUCT IN A WELL

VENTILATED AREA CAN CAUSE PROPERTY DAMAGE, INJURY OR DEATH.

Warning: Excessive weight hazard!

!

NEWAGE

PERFORMANCE

40” GRILL

NATURAL GAS

SKU#66982  NEWAGE PERFORMANCE 40” GRILL  NG

SKU#66281  NEWAGE PERFORMANCE 40” GRILL  NG

WITH NEWAGE 40” GRILL CART

The NewAge grill must be installed by a licensed

gas tter, in accordance with the manufacturer’s

instructions and all applicable codes and

requirements of the authority having jurisdiction.

If the information in the grill’s instructions are not

followed exactly, a re, explosion or production

of carbon monoxide may result causing property

damage, personal injury or loss of life. The

licensed gas tter is responsible for the proper

installation of the grill.

WARNING

For the online installation manual and videos regarding this product, please check out our support hub via:

https://newageproducts.com/support-hub/

IM-GLE.01A-02

Read and follow the instructions in this manual fully and completely before installing,

servicing or operating the grill to reduce the risk of :

1. 1. Fire

2. 2. Personal injury or property damage

3. 3. Improper installation

THIS PRODUCT IS DESIGNED FOR OUTDOOR USE ONLY. DO NOT INSTALL OR OPERATE

INDOORS, IN A GARAGE, IN A SCREENED IN PORCH, GAZEBO, OR ANY OTHER ENCLOSED AREA.

THIS OUTDOOR COOKING GAS APPLIANCE IS NOT INTENDED TO BE INSTALLED IN OR ON

RECREATIONAL VEHICLES , BOATS OR IN A NONVENTILATED ROOM. FAILURE TO OPERATE THIS

PRODUCT IN A WELL VENTILATED AREA CAN CAUSE PROPERTY DAMAGE, INJURY OR

DEATH. KEEP THE AREA SURROUNDING THE GRILL CLEAR AND FREE FROM COMBUSTIBLE

ATERIALS, GASOLINE AND OTHER FLAMMABLE VAPORS AND LIQUIDS.

DANGER

Do not store or use gasoline or other ammable liquids or vapors in the vicinity of this or any

other appliance.

The installation must conform with local codes or, in the absence of local codes, with either

the National Fuel Gas code, ANSI Z223.1/NFPA 54 or the National Gas and Propane installation

code, CSA B149.1, or the Propane Storage and Handling Code, CSA B149.2, or the Standard for

Recreational Vehicles, ANSI A119.2/ NFPA, and CSA Z240 RV Series, Recreational Vehicle Code as

applicable.

WARNING

1. 1. The outdoor cooking gas appliance and its individual shuto valve must be disconnected

from the gas supply piping system during any pressure testing of that system at test

pressures in excess of 0.5 psi (3.5 kPa).

2. 2. The outdoor cooking gas appliance must be isolated from the gas supply piping system

by closing it individual manual shuto valve during any pressure testing of the gas supply

piping system at test pressures equal to or less than 1/2 psi (3.5 kPa).

CAUTION

IF YOU SMELL GAS:

1. Shut o gas to the appliance.

2. Extinguish any open ame.

3. Open the lid.

4. If odor continues, keep away from the appliance and immediately call your gas supplier or

your re department.

DANGER

WARNING

1. Massachusetts requires all gas be installed using a plumber or licensed gas tter carrying the

appropriate Massachusetts license.

2. All permanently-installed natural gas installation require a “T” handle type manual gas valve

be installed in the gas supply line to this appliance.

STATE OF MASSACHUSETTS

WARNING

1. This product can expose you to chemicals including Carbon Monoxide, which is a by-

product of combustion known to the State of California to cause cancer and birth defects

or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

2. California law requires businesses to warn customers of potential exposure to such

substances. To minimize exposure to the substances, always operate this unit according

to the use and care instructions found in this manual. Be certain to provide adequate

ventilation when cooking.

3. California Proposition 65 lists “Silica, crystalline” which is used in one of the components of

the IR burner, as an agent known to the state of California to cause cancer.

CALIFORNIA PROPOSITION 65

WARNING

1. Always maintain the required clearances from combustible construction as detailed. The grill

is designed for outdoor use only. Never use in a garage, building, shed, breezeway or other

enclosed area. This grill shall not be used under any unprotected overhead combustible

construction.

2. Gas grills are not design certied for and are not to be installed in or on recreational vehicles,

portable trailers, boats or any other moving installation.

3. Keep any electrical supply cord and the fuel supply hose away from any heated surfaces.

Electrical cords should be placed away from walkways to avoid creating a tripping hazard.

4. Do not repair or replace any part of the grill unless specically recommended in this manual.

5. All gas lines must have a shut-o that is readily and easily accessible. Be sure the owner

knows where the shut-o is located. If you smell gas, check for gas leaks immediately. Check

only with a soap and water solution. Never check for gas leaks with an open ame.

(See INDEX: “Leak Testing” for further details.)

IMPORTANT NOTES

This Gas Barbecue Is Certied Under Canadian And American National Standards, ANSI Z21.58-

2018 and CSA 1.16-2018 respectively for Outdoor Gas Grills and should be installed to conform

with local codes. In absence of local codes, install to the current CAN B149.2 Natural Fuel Gas

Code and the Propane Installation Code, CSA B149.1 Propane Installation Code in Canada or to

the National Fuel Gas Code, ANSI Z223.1/NFPA 54 the National Fuel Gas Code the Natural Gas and

Propane Installation Code, CSA B149.2.

Index

Safe Operating Practices 6

Parts Supplied 11

Tools Needed 12

Product Inspection 12

Product Specications 13

Installing Grill on custom built cabinet 17

Installing Grill on custom built cabinet 18

Assembling the Grill 21

Optional Accessories 23

Gas Connections 26

Leak Testing Instructions 30

AA Battery Maintenance 32

Pre-Grill Checklist 33

Lighting the Grill 34

Proper Burner Position and Operation 37

General Grill Operation and Cooking Procedures 40

Grill Maintenance and Cleaning 44

Troubleshooting 48

Exploded View and Spare Parts 51

5

Scan this QR code with the camera

on your mobile device to visit the

NewAge Products Support Hub

www.newageproducts.com/support-hub/

NEWAGE PRODUCTS INC. PERFORMANCE

GRILLS MANUFACTURER WARRANTY

PROOF OF PURCHASE IS REQUIRED

TO OBTAIN WARRANTY SERVICE.

Please have the following information available when you call our

customer service team:

• Name, address and telephone number

• Product Name / SKU Number

• A clear, detailed description of the problem

• Proof of purchase including order number

Register your NewAge Products purchase online for quicker customer

assistance and access to exclusive beneﬁts

Visit www.newageproducts.com/register/

Warranty Claim

For warranty service please contact NewAge Products at

1-877-306-8930; or [email protected]

Please review all warranty details below, prior to contacting NewAge Products for a claim.

Scan the QR code on the right to access our support page or

visit www.newageproducts.com/contact-us/

The 304 stainless steel material used in the construction of NewAge Platinum Grill is highly rust resistant, however, chlorine in the air from

swimming pools or the salt from sea air may cause surface rust to appear and even create some pitting corrosion if left on the product. We suggest

cleaning all stainless steel surfaces at least every two weeks to keep your Grill in prime condition. The chemical reaction from salt is easy to

WHAT IS COVERED

When this product is installed, operated and maintained according to the instructions attached to or furnished with the product, NewAge Products

Inc. will replace the defective product or parts if the part fails as a result of defective materials or workmanship for the warranty duration from the

purchase date of the product.

1. Service calls to correct the installation of any NewAge products or to instruct you how to use or install them.

2. Damage resulting from products caused by accident, misuse, abuse, ﬁre, ﬂood, improper installation, acts of God, neglect, modiﬁcation or

mishandling, improper maintenance & storage.

3. Products damaged by improperly loading beyond the speciﬁed maximum weight capacity outlined in the instructions provided with the

product.

4. Repairs or replacement when your product is used in other than normal, residential use, such as a commercial environment, or handled in

anyway inconsistent with the installation instructions included with the product.

5. Cosmetic damage that occurs after customer purchasing the product, including scratches, dings, dents, corrosion, or stains in the material that

6. Surfaces damaged due to improper use of chemicals, and detergents.

7. Discoloration due to the heat, for example beside a grill, is a trait of stainless steel.

8. Surface rust resulting from acid rain or environmental chemicals

9. Replacement parts for NewAge products outside Canada and the United States.

10. Loss due to theft.

11. Damage resulting from use of the product contrary and not in accordance to the instruction manual.

12. Any labor costs during the warranty period.

WHAT IS NOT COVERED

DISCLAIMER OF IMPLIED WARRANTIES

IMPLIED WARRANTIES, INCLUDING TO THE EXTENT APPLICABLE WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,

ARE EXCLUDED TO THE EXTENT LEGALLY PERMISSIBLE. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO ONE YEAR, OR

THE SHORTEST PERIOD ALLOWED BY LAW. THIS WARRANTY IS LIMITED TO THE ORIGINAL BUYER. Some states and provinces do not allow limitations

on the duration of implied warranties of merchantability or ﬁtness, so this limitation may not apply to you. This warranty gives you speciﬁc legal rights, and

you also may have other rights that vary from state to state or province to province.

LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR OR REPLACEMENT AT OUR DISCRETION

AS PROVIDED HEREIN. NEWAGE SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not

allow the exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty

gives you speciﬁc legal rights, and you also may have other rights that vary from state to state or province to province.

NewAge is proud to oer a 10 Years Limited Warranty from the date of purchase. This is subject to the limitations and disclaimers set forth below and other

product documentations.

10 YEARS LIMITED WARRANTY

Length of Warranty Warranty Covered Items Cost to NewAge Cost to Customer

5 Years Cooking Grates, Grease Trays, Main Burners, Sear Burner (only applicable for

Performance 40” Grill Appliance) Materials Shipping

10 Years Stainless Steel Lid / Burner Box/ Interior Brackets Materials Shipping

2 Years All other parts Materials Shipping

6

Safe Operating Practices

1. Newage Grill must be assembled and installed according to the instructions in the manual.

2. Read the entire instruction manual prior to operating grill.

3. NewAge Grill must be used outdoors in a well ventilated area, and cannot be used indoors, in a enclosed

area such as a garage, gazebo, screened in porch or other similar enclosed area.

4. NewAge grills are not designed or certied for and are not to be installed in or on recreational vehicles,

portable trailers, boats.

5. Never use the grill in windy conditions. If located in a consistently windy area, oceanfront, mountaintop,

etc., a windbreak will be required. Always adhere to the specied clearances as described in the

INSTALLATION section of this manual. Refer to the page 10 for additional information.

6. Do not modify the NewAge Grill.

7. Do not operate the NewAge Grill under, or near combustible construction.

8. Maintain proper clearance to combustibles, 18” (457 mm)to rear of unit, 14” (356mm) to sides. Additional

clearance of 32” (810mm) is recommended near vinyl siding or panes of glass.

9. When not in use turn o the gas at the supply valve.

10. Always shut o the main valve on the Natural gas supply after each use.

11. Never attach or disconnect to gas supply, or move or alter gas ttings when the grill is in operation or is

hot.

12. Natural gas units must be disconnected from the supply when being stored indoors.

13. Inspect the fuel supply hose before each use. If there is evidence of excessive abrasion or wear or the

hose is cut, it must be replaced prior to using the gas grill with a replacement hose assembly specied by

the grill manufacturer.

14. Leak test the unit before initial use, annually, and whenever any gas components are replaced. Refer to

page 8 for additional information.

15. Follow lighting instructions carefully when operating grill.

16. Burner controls must be o when turning supply valve on.

17. The grill hood must be fully opened while lighting the grill. Failure to do so will risk an explosion, and

personal injury or death.

18. Never lean over the grill and keep face away from grill when lighting.

19. Never let your gas hose touch your burner box. Refer to page 9 for additional information.

20. Always use a covered hand when opening the grill lid and only do so slowly to allow heat and steam to

escape.

21. Do not leave grill unattended when operating.

22. Do not use aluminum foil to line drip pans or grill grates or radiants. This can severely upset combustion

air ow or trap excessive heat in the control area. The result of this can be melted knobs or damaged

ignition components.

23. Adults and children should be instructed on the hazards of high surface temperatures. Never leave

children unsupervised around the NewAge Grill.

24. Never touch the grill racks, hood or immediate surrounding metal surfaces with your bare hands while

grilling.

7

Safe Operating Practices

25. The NewAge Grill must be cooled before it is covered. Never place the cover on when cooking or while

hot.

26. Never grill without the drip pan installed. Hot grease can leak down and produce a re or explosion.

27. Clean grease trays regularly to prevent grease res. Refer to page 8 for additional information.

28. Spiders and insects like to nest in the burners, venturis, valves and orices of a grill, disrupting the gas

ow. This very dangerous condition can cause a re behind the control panel, damaging the grill and

risking personal injury. If your grill has been unused for a long time, inspect and clean the burners,

venturis, valves and orices.

29. Clean the grill with caution. Avoid steam burns; do not use a wet sponge or cloth to clean the grill while

it is hot. Some cleaners produce noxious fumes or can ignite if applied to a hot surface.

30. Do not locate, store or operate the grill on an inclined plane. If you are using a grill cart, make sure you

lock the castor wheels before operating the grill.

31. Do not move the appliance during use.

32. Do not use a power washer to clean the NewAge Grill.

33. Always have an ABC Fire Extinguisher accessible — never attempt to extinguish a grease re with water

or other liquids.

34. Make sure the licensed gas tter shows you where your gas supply shut-o is located. All gas lines must

have a shut-o that is readily and easily accessible. If you smell gas, check for gas leaks immediately.

Check only with a soap and water solution.

35. For personal safety, wear proper apparel while barbecuing.

36. Do not use the grill for cooking excessively fatty meats or products, which promote are-ups. To Control

are-ups, adjust the controls to lower the temperature. If your grill are-up is out-of-control, turn o the

burners. Don’t use water to put out are-ups. Spraying water on a are-up can cause grease to explode.

37. Make sure that the AA batteries (rechargeable and non-rechargeable) are removed from the Pulse

Ignitor/ decomposed/ scraped after recommended AA battery life by the manufacturer.

38. NEVER use physically damaged AA batteries, it may corrode the inner parts or completely damage the

Pulse Ignitor.

Note: THIS MANUAL MUST REMAIN WITH THE PRODUCT OWNER FOR FUTURE REFERENCE

8

Regularly clean your grill components to prevent

are-ups and grease res

Just like the cooking appliances in your home, your NewAge Grill needs to be

regularly cleaned and maintained to operate at peak performance. This not

only produces tastier, healthier food, but it reduces the chance of dangerous

are-ups or grease res.

Here are the key areas to keep clean:

1. Remove cooking grates and scrape excess food particles with a BBQ brush

after every use. For a deep clean, soak and scrub with dish soap and water a

few times per season.

2. Pull out the grease tray after every use and scrape o any grease or food

chunks. Wash with dish soap and water to keep it sparkling clean.

3. Your Flame Tamer Panels will accumulate a lot of burnt on sauces and

grease drippings. Remove residue from the Panels with a scraper, and use a

wire brush to clear debris from the Flame Tamers.

4. Burners that aren’t used frequently can get blocked by spiders who are

drawn to the gas smell, and build webs inside the burner tubes. Use a wire-

brush to clean the inside of the burners and remove debris from the outside

of the burners.

5. Scrape down the interior of your burner box at least once a season to re-

move carbon build-up. Scoop or vacuum out the debris, reinstall all compo-

nents and enjoy a much cleaner grilling experience.

Test your hose connections for gas leaks

Gas leaks are a serious issue that can be easily avoided by doing a quick and

simple leak check annually, or whenever gas components are replaced or

serviced.

1. Ensure that all grill control knobs are in the o position.

2. Turn on the fuel supply,

For Natural Gas

Turn the valve handle 1/4 turn to align with the gas ow.

3. Brush or spray a half-and-half solution of liquid soap and water

onto all joints and connections of the regulator, hose, manifolds

and valves.

4. Bubbles will indicate a gas leak. IMMEDIATELY turn o the gas

supply and do not use the grill until contacting a

licensed gas tter to replace faulty parts.

WARNING

The leak test must be done before initial use, annually, and whenever any gas components are

replaced or serviced. Do not smoke while performing this test and remove all sources of ignition.

See Leak Testing Diagram for areas to check. Never conduct a leak test using re or ame. Sparks or

open ames will result in a re or explosion, damage to property, serious bodily injury or death.

Leak Testing Diagram

Safe Operating Practices

50% WATER

50% LIQUID

SOAP

9

Never let your gas hose touch your burner box

The underside of your grill gets incredibly hot. Pushing your excess gas line into the cavity below your grill, or coiling it

beneath the burner box can melt the exterior coating of the gas hose and cause a re.

Take these steps to make sure your hose is positioned safely:

1. Ensure your grill is o and cooled down.

2. Kneel down and look in the cavity for the hose at the left-hand side of the grill.

3. If the hose is bunched up, or touching the rebox, pull the gas hose from the bottom of the cabinet until any excess

line is removed.

4. Check the hose for signs of melting or damage. If the damage has

occurred, or you are unsure of how to check, contact Customer Support Team > 1-877-306-8930;

or support@newageproducts.com

Safe Operating Practices

10

Safe Operating Practices

Grilling in windy conditions

Wind Direction

Flame

Burner

Flame Lift o

Exhaust

Min 3”

Flame

Burner

Note

Any damage caused from use in windy conditions, such as melted knobs or igniter wires, or control panel discoloration

from heat buildup, is excluded form warranty coverage.

WARNING

Using your grill in windy conditions may disrupt the front-to-back airow. If, while grilling with all burners on high

and the hood closed, you notice that the temperature gauge fails to rise.....be careful. If wind has kept hot gases from

exiting the rear of the grill the control panel and knobs may have become extremely hot.

During the high wind conditions, it is best if you don’t use your grill. If located in consistently windy area (oceanfront,

mountaintop, etc.) a wind break will be required. Always adhere to the specied clearances as dened in the “Installation

Manual“.

Wind Direction

Flame

Burner

Flame Lift o

Exhaust

Non-Combustible

Min 4”

Flame

Burner

Note:

Make sure to maintain clearance from the windscreen as specied below.

• 4” for non-combustible material.

• 18” for Combustible material.

11

Parts Supplied

1x SS Warming

Rack

1x Natural Gas

Hose (Pre-insalled) 4x M6 Flat Head

Screws

4x Cooking Grate

3x Flame Tamer

Panel

2x Spare Rubber

Bumpers

Main Grill Parts

Optional Accessories

*Accessories oering depends on location and subject to change.

Griddle

SKU#66940 SKU#66946

Smoker Box

12

Product Inspection

• Check to see all parts are received as per the

order placed.

• Contact NewAge Products at 1-877-306-8930;

for any missing parts.

• Inspect the products for any damages before

starting the installation.

• Go through the installation instructions carefully

before starting the installation.

Tools Needed

Box Cutter

6mm

Open Wrench

Gas Line

Pipe Dope

#2 Phillips head

screwdriver

Pipe Dope -

Thread Sealant

Tape Measure

13

Product Specications

NewAge Grill 40”

H

WD

Width (W) 40”

Depth (D) 23.58”

Height (H) 23.10”

Material Stainless Steel Main Grilling Area 634 Sqare Inches

Primary Burner BTU 12,000 BTUs x3 Warming Rack Area 290 Square Inches

Sear Burner BTU 12,000 BTUs x1 Cutout Width 38.5”

Fuel Type Natural Gas Cutout Depth 22.3”

Total Power Output 51,000 BTUs Cutout Height 11.2”

Net Weight 136.35 Lbs

Dimensions

Details

14

Lock the Casters (if applicable). Pick the

appliance from the shipping pallet, and

place it onto the Cabinet/Cart directly.

Installing Grill on NewAge Grill Cabinet/Cart

Secure grill to Cabinet/Cart by inserting

two M6x12mm screw supplied with

NewAge Cabinets/Carts from the bottom.

While connecting the gas hose to the grill,

make sure the hose is not bunched up

below the grill.

1

3

For more detailed instructions on installation steps, refer to the NewAge Grill Cabinet/ Cart

installation guide. NOTE: When you are ready to install the

appliance, place it directly onto the Cabinet/

Cart.

DO NOT place the appliance on oor or at

surface.

15

Installing Grill on NewAge Grill Cabinet/Cart

NOTE: Route the Power cable outside the cart back panel. DO NOT route the cable through

underneath the Grill. (Applicable to Grill Cabinets and Carts both)

NOTE: While connecting the gas hose to the grill, make sure the hose is not bunched up below the grill.

(Applicable to Grill Cabinets and Carts both)

16

Installing Appliance on NewAge Grill Cabinet

NOTE: Route the Power cable outside the cabinet back panel. DO NOT route the cable through

underneath the Grill. (Applicable to Grill Cabinets and Carts both)

NOTE: While connecting the gas hose to the grill, make sure the hose is not bunched up below the grill.

(Applicable to Grill Cabinets and Carts both)

Appliance back panel

Appliance

back panel

17

Installing Grill on custom built cabinet

The installation must conform with local codes or, in the absence of local codes, with the

National Fuel Gas Code, ANSI Z223.1/NFPA 54, Storage and Handling of Liqueed Petroleum

Gases, ANSI/NFPA 58; or Natural Gas and Propane Installation Code, CSA B149.1; Propane

Storage and Handling. If you are connecting an appliance to a xed fuel piping system

specifying the use of a rigid pipe, semi-rigid tubing, and/ or a connector that complies

with the standard for Connectors for Outdoor Gas Appliances and Manufactured Homes,

ANSI Z21.75 CSA 6.27.

WARNING

Cabinet frame, cabinet side

panels and counter top must be

made from non-combustible

material.

WARNING

DO NOT store or use products with

ammable liquids or vapors in the vicinity of

the NewAge Grill Cabinet,NewAge Outdoor

Kitchen cabinets or any appliances.

Note to licensed gas tter:

All built-in appliances must use rigid pipe, semi-rigid tubing, or a connector complying with the

standard for Connectors for Gas Appliances, ANSI Z21.24. CSA 6.10, or Standard for Connectors for

Outdoor Gas Appliances and Manufactured homes, ANSI Z21.75. CSA 6.27, for the appliance which

are connected to xed fuel piping system (Natural Gas).

WARNING

This grill is designed for non-combustible enclosures only, and must be installed and serviced by

a licensed gas tter to local codes.

As indicated on the rating plate, this gas grill is designed to operate with supply pressure of 7”

WC for Natural Gas. For installations where the gas supply pressure exceeds these requirements,

a regulator must be installed upstream of the grill’s components. If the gas supply pressure is

lower than these requirements, the unit will be under-red and will not reach the maximum

temperatures. Ensure that the supply line size complies with local and/ or national installation

codes.

18

Installing Grill on custom built cabinet

CLEARANCES:

TO NON-COMBUSTIBLE CONSTRUCTION

A minimum of 4” (10 cm) clearance from the back of the grill to non-combustible construction is

required to allow the hood to be opened fully.

TO COMBUSTIBLE CONSTRUCTION

This appliance should NOT be installed over, under or next to unprotected combustible

construction. A minimum clearance to vertical and rear combustible material is 18” (45 cm) and 14”

(36cm) on the sides.

VENTILATION OPENINGS

A minimum of three 10 in² (65 cm²) of ventilation openings must be provided at the bottom of both

left and right sides of your enclosure (island), as well as the back side. A minimum of three 20 in²

(130 cm²) of ventilation openings must be provided at the top of both left, right and back sides of

your enclosure (island) where the top of the opening aligns with the bottom of the grill cut-out.

These openings are required to safely dissipate gas vapors if there is a leak in your enclosure.

The minimum vertical clearance to combustible materials means that ALL combustible materials

must be outside this 18” (45cm) zone. As an example, if you have an island with a stucco or

tiled surface and wood-frame construction beneath, the wood is considered combustible, even

though the grill is touching the stucco or tile surface, which is non-combustible. In extreme

circumstances, the wood could potentially get hot enough to burn.

CUTOUT DIMENSIONS FOR INSTALLING GRILL ON A CUSTOM BUILT CABINET

Cutout Dimensions

SKU W D H

33” Grill 66980

66990 31.5” 22.3” 11.2”

36” Grill 66981

66991 34.5” 22.3” 11.2”

40” Grill 66982

66992 38.5” 22.3” 11.2”

Side Burner 66983

66993 15.3” 22.4” 11.3”

19

Installing Grill on custom built cabinet

10in

1in

MINIMUM 10 SQ IN (65 SQ CM)

OF VENTILATION REQUIRED

MINIMUM 20 SQ IN (130 SQ

CM) OF VENTILATION

REQUIRED.

Back View

NOTE: These illustrations are for reference purpose only. Actual built-in cabinets and installation

may dier.

Layout for Non-combustible enclosure

NON-COMUSTABLE MATERIAL

MINIMUM 20 SQ IN (130 SQ

CM) OF VENTILATION

REQUIRED ON EACH END OF

CABINET.

5"

2.375” Dia

127mm

MAXIMUM

1"

25.4mm

MAXIMUM

W

D

H

PARTITION TO ISOLATE

CYLINDER FROM GRILL

MINIMUM 10 SQ IN (65 SQ CM)

OF VENTILATION REQUIRED ON

EACH END OF CABINET.

Rubber grommet

Note: Avoid abrasion of hose against the

opening. It is recommended to use a rubber

grommet at the opening.

H1

W1

WARNING

• The upper vent opening must be at least 20

square inches.

• The lower vent opening must be at least 10

square inches.

20

Rigid Connection in a Built in Enclosure

WARNING

Only licensed gas tter must perform the required gas tting on NewAge gas appliances.

To ensure satisfactory performance, the gas supply line must be sized to accommodate the total

BTU/h requirements of all the gas-red equipment that will be connected to that line.

In no case should pipe less than 3/4” inside diameter or 1” outside diameter ever be used to

connect this product.

Natural Gas Installation

Ventilation

Securely mount the gas

supply components to the

non combustionable

structure. This illustration is for

reference only each

installation will be dierent.

Rigid Piping for supply

(Not Supplied)

Quick Disconnect Coupling NG

(Not Supplied)

Flexible Gas Hose

Supply line

All Other Components are Not Supplied.

Grill Gas line Flexible

corrugated Tubing

(Not Supplied)

Natural gas Supply

Line

Natural Gas

Regulator

Natural gas Hose

(Supplied)

Non - combustible

Construction

Natural gas Hose

(Supplied)

La page charge ...

NewAge Products 66982 Mode d'emploi

NewAge Products 66982 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents