dji Matrice 350 RTK Mode d'emploi

User Guide

使用说明

使用說明

ユーザーガイド

사용자 가이드

Bedienungsanleitung

Guía de usuario

Guide de l’utilisateur

Guida all’uso

Gebruikershandleiding

Manual do utilizador

Guia do usuário

Руководство пользователя

D-RTK 2

High Precision GNSS Mobile Station

2023.06v2.6

1

Contents

EN

CHS

CHT

JP

KR

DE

ES

FR

IT

NL

PT

PT-BR

RU

Compliance Information 152

User Guide 2

使用说明 13

使用說明 24

ユーザーガイド 35

사용자 가이드 46

Bedienungsanleitung 57

Guía de usuario 69

Guide de l’utilisateur 81

Guida dell’utente 93

Gebruikershandleiding 105

Manual do utilizador 117

Guia do usuário 129

Руководство пользователя 140

2

EN

Disclaimer

Thank you for purchasing D-RTKTM 2 High Precision GNSS Mobile Station (hereinafter referred to as

the “Product”). Read this disclaimer carefully before using this Product. By using this Product, you

hereby agree to this disclaimer and signify that you have read it fully. Please use this Product in strict

accordance with the manual and be sure to pay attention to the Warnings. SZ DJI TECHNOLOGY

CO., LTD., and its afliated companies assume no liability for damage(s) or injuries incurred directly or

indirectly from using, installing or retting this Product improperly, including but not limited to using non-

designated accessories.

DJITM is a trademark of SZ DJI TECHNOLOGY CO., LTD. (abbreviated as “DJI”) and its affiliated

companies. Names of products, brands, etc., appearing in this manual are trademarks or registered

trademarks of their respective owner companies. This Product and manual are copyrighted by DJI with

written consent or authorization of DJI.

This disclaimer is produced in various languages. In the event of divergence among different versions,

the Chinese version shall prevail when the Product in question is purchased in China, and the English

version shall prevail when the Product in question is purchased in any other region.

Warnings

1. To maximize the lifespan of the battery, remove the Intelligent Battery from the D-RTK 2 Mobile

Station when not in use.

2. Only use the D-RTK 2 in the corresponding frequency band and in accordance with local laws and

regulations.

3. DO NOT bend or fold the cables excessively.

4. Ensure that the D-RTK 2 Mobile Station is perfectly level when mounted and placed.

5. Only operate in an open environment free from radio interference. Turn off nearby devices using the

same frequencies as the D-RTK 2 Mobile Station (e.g. radio transceivers).

6. Ensure that the antennas of all the devices used are unobstructed when in use.

7. Only use genuine DJI parts or parts certified by DJI. Unauthorized parts or parts from non-DJI-

certied manufacturers may cause the system to malfunction and compromise safety.

8. Ensure that the D-RTK 2 Mobile Station and its components are free from contamination (e.g. water,

oil, soil and sand).

9. DO NOT attempt to disassemble any part of the D-RTK 2 Mobile Station that has already been

mounted prior to shipping.

10. Handle the sharp ends of the extension rod and tripod with caution.

11. Take necessary measures to protect the D-RTK 2 Mobile Station and batteries from water in rain,

snow, and/or thunderstorms. Operate with caution in severe weather conditions.

Introduction

The D-RTK 2 High Precision GNSS Mobile Station is a high-precision satellite signal receiver that

supports four global satellite navigation systems: GPS, BEIDOU, GLONASS, and Galileo with 11-

band satellite signal* reception. Its built-in OCUSYNCTM transmission links ensure uninterrupted, stable

data transmission. The D-RTK 2 Mobile Station can be used as an RTK mobile base station to achieve

centimeter-level positioning accuracy of an aircraft equipped with a DJI RTK positioning system (such as

DJI INSPIRETM 3, AGRASTM T40, T20P, T30, T10, T20, T16, MG-1P RTK, Phantom 4 RTK, P4 Multispectral,

MATRICETM 350 RTK, Matrice 30, Matrice 30T, Matrice 300 RTK, or Matrice 210 RTK V2). Its functions are

uncompromised even in environments with strong magnetic interference, for example, near high-voltage

power lines or metal structures. The D-RTK 2 Mobile Station can also be used as a handheld mapping

device to achieve enhanced precision in point positioning during surveying and mapping, or lofting and

other engineering applications.

* Refer to the Specications for details.

3

EN

In the Box

Optional Items

D-RTK 2 Body Extension Rod Charging Hub (USB-C)×1 ×1 ×1

Intelligent Battery (WB37) Battery Cover 65W Portable Charger* ×1 ×2 ×1

USB-C Cable Hex Key×1 USB-C OTG Cable ×1 ×1

Use the Power Adapter Cable and AC Power Adapter to connect to the AC power for long-term power supply.

When using the D-RTK 2 Mobile Station as a mobile base station, use the Tripod to support the D-RTK 2 body.

Tripod AC Power CableAC Power AdapterPower Adapter Cable

* The type and quantity vary depending on the region.

4

EN

Overview

D-RTK 2 Body Tripod

1. Antenna

2. Link Button and Indicator

3. Power Button and Indicator

4. Operating Mode Button and Indicator

5. USB-C Port

6. Rosette Mount

7. Battery Compartment

8. Battery Cover

9. Lock Nut

10. External Power Port*

1. Sleeve

2. Mount Base

3. Retractable Legs

4. Knobs

* Equipped with a protective cover that can be stored when the unit is in use.

When not in use, cover the ports to protect the unit from moisture and dust.

Bottom View

The illustrations in this document may be slightly different from the actual

product. Please refer to the actual one.

6

7

8

9

10

1

2

3

4

1 234

5

EN

Preparation

Charging the Battery

Press the battery level button once to check the battery level. Fully charge the batteries before rst-

time use.

1. Insert the batteries into the charging hub until there is a click, connect the charger to the power port

on the charging hub, and connect the charger to a power outlet (100-240 V, 50/60 Hz).

2. The batteries will be charged in sequence according to the power levels from high to low. The status

LEDs will glow solid white after the corresponding battery is fully charged. Remove the battery from

the charging hub.

Refer to the WB37 Battery Charging Hub (USB-C) User Guide and the WB37 Intelligent Battery

Safety Guidelines for more details.

Mounting the Battery

Powering the D-RTK 2 Mobile Station On/Off

Press and hold the power button to power on/off the D-RTK 2 Mobile Station.

Power Button

6

EN

Power Indicator Descriptions

Solid Red System initializing/error notication

Quick Red Blink Battery level is less than 20%

Slow Red Blink Signals from ≤ 5 Satellite received

Solid Yellow Signals from 6-9 Satellite received

Solid Green Signals from ≥10 Satellite received

Operating Modes

The D-RTK 2 Mobile Station provides ve operating modes to use with different products. Follow the

instructions below to switch between modes.

1. Press and hold the Operating Mode button for two seconds. The indicator will turn from green to

yellow to indicate that the device has entered mode switch status.

2. Press the Operating Mode button once to switch modes. Wait two seconds for the device to enter the

corresponding mode. The indicator will turn from yellow to green. Operating modes are indicated by

the blinking pattern of the indicator. Refer to the table below.

3. The device will remain in the original mode if there is no further operation within two seconds of

entering the mode switch status.

Modes Name and Compatible Products Blinking Pattern

Operating Mode 1 Mobile Base Station

(T20/T16/MG-1P RTK/Phantom 4 RTK/P4 Multispectral) Once

Operating Mode 2 Reserved Twice

Operating Mode 3 Handheld Mapping Device

(T20/T16/MG-1P RTK/Phantom 4 RTK) Three Times

Operating Mode 4 Mobile Base Station (M210 RTK V2) Four Times

Operating Mode 5 Mobile Base Station (Broadcast Mode, Inspire 3/M350 RTK/M30/M30T/

M300 RTK/T40/T20P/T30/T10) Five Times

How to Use the D-RTK 2 Mobile Station

The operations are similar when using the D-RTK 2 Mobile Station with different products. Unless

otherwise specified, the descriptions below are compatible with all the products working in the

corresponding mode.

Connecting to the Remote Controller or Aircraft

Connection Method

The connection method vary depending on the operating mode. See the instructions below.

Operating Mode 1

Using with Agras T20/T16/MG-1P RTK or Phantom 4 RTK Aircraft

The D-RTK 2 Mobile Station must be linked to the remote controller in the app. The following

descriptions use the DJI Agras app as an example.

1. Power on the D-RTK 2 Mobile Station, wait until system initialization is completed, and enter

Operating Mode 1.

2. Power on the remote controller and make sure that the app is launched.

3. In the app, go to Operation View > > RTK to enable aircraft RTK function. Select the RTK signal

source to D-RTK 2 Mobile Station. Then, tap Linking at the bottom. The remote controller status

indicator will blink blue and a beeping sound from the remote controller will indicate that the remote

controller is being linked.

4. Press the Link button on the D-RTK 2 Mobile Station and the link indicator will blink red and green

alternately, indicating that the D-RTK 2 Mobile Station is being linked.

7

EN

5. The linking is successful when the indicator light on the remote controller becomes solid green. The

D-RTK 2 link indicator shows the current working status. Refer to the table below for the details.

6. The remote controller and aircraft must be relinked after the remote controller is linked with the D-RTK

2 Mobile Station. There are three ways that this can be done:

• After linking the remote controller with the D-RTK 2 Mobile Station, tap Link with Aircraft in the pop-

up window to link it with the aircraft. Then press the Link button on the aircraft to nish linking.

• On the RTK Settings page, tap the button next to the prompt indicating the aircraft has been

disconnected, and then tap Link with Aircraft in the pop-up window to link it with the aircraft.

• Link the remote controller with the aircraft on the RC Settings page. When nished, go to the RTK

Settings page and tap Try to Reconnect next to the D-RTK 2 Status to reconnect to D-RTK 2. The

D-RTK 2 status must indicate Connection Success for the RTK functions to work.

Using with P4 Multispectral Aircraft

1. Power on the D-RTK 2 Mobile Station, wait until system initialization is completed, and enter

Operating Mode 1.

2. Power on the remote controller and make sure that the DJI GS Pro app is launched.

3. Go to Mission Page in DJI GS Pro, tap the icon or RTK on top of the screen to go to the RTK

settings menu, and then select D-RTK 2 as the RTK signal source. Enable the aircraft RTK at the

bottom of the menu to ensure the aircraft has access to RTK data.

4. Tap Link. The remote controller will start beeping. Then press the link button on the mobile station.

5. The linking is successful when the indicator light on the remote controller becomes solid green. The

D-RTK 2 link indicator shows the current working status. Refer to the table below for details.

• When the D-RTK 2 Mobile Station has been connected to the remote controller and the

aircraft is being controlled by the remote controller, the D-RTK 2 Mobile Station cannot

be linked with other remote controllers. If required, link after the aircraft lands and the

motors stop.

• One D-RTK 2 Mobile Station can link with up to ve remote controllers.

Operating Mode 3

The D-RTK 2 Mobile Station must be linked to the remote controller.

1. Power on the D-RTK 2 Mobile Station, wait until system initialization is completed, and enter

Operating Mode 3.

2. Power on the remote controller. Go to Remote Controller Settings in the app, and tap Linking. The

status LED blinks blue and the remote controller will beep twice repeatedly, indicating that the

remote controller is ready to link.

3. Press the Link button on the D-RTK 2 Mobile Station and the link indicator will blink red and green

alternately, indicating that the D-RTK 2 Mobile Station is being linked.

4. The linking is successful when the indicator light on the remote controller becomes solid green. The

D-RTK 2 link indicator shows the current working status. Refer to the table below for details.

Operating Mode 4

The D-RTK 2 Mobile Station must be linked to the M210 RTK V2 aircraft.

1. Power on the M210 RTK V2 aircraft and make sure that it is linked to the remote controller.

2. Press the Link button on the D-RTK 2 Mobile Station and the link indicator will blink red and green

alternately, indicating that the D-RTK 2 Mobile Station is being linked.

3. Press the Link button on the aircraft.

4. Wait for a few seconds. The linking is successful when the indicator lights on both the aircraft and

mobile station become solid green.

Operating Mode 5

When using with the Inspire 3/M350 RTK/M30/M30T/M300 RTK/T40/T20P/T30/T10, the remote controller

must join the broadcast network of the D-RTK 2 Mobile Station.

1. Power on the D-RTK 2 Mobile Station, wait until system initialization is completed, and enter

Operating Mode 5.

2. Power on the remote controller. Go to RTK Settings in the app, and set the RTK signal source to D-RTK

2 Mobile Station.

8

EN

2. Insert the extension rod into the tripod and tighten the sleeve on the tripod. Then attach the D-RTK 2

body onto the extension rod and tighten the lock nut on the D-RTK 2 body. Ensure that the bubble of

the bubble level on the D-RTK 2 is located within the black circle (viewed from the top of the bubble

level vertically).

3. Tap on the right of the D-RTK 2 Mobile Station status display and a search will start automatically.

Select the desired RTK base station in the search results and wait for a successful connection.

Link Indicator Descriptions

When the linking process starts, the indicator blinks red and green alternately.

When the linking process is nished, the indicator blinking patterns are as shown below.

Operating Mode 1/3/4 Status

Solid Green OcuSync signal quality >70%

Quick Green Blink OcuSync signal quality 35%-70%

Slow Green Blink OcuSync signal quality ≤ 35%

Solid Red OcuSync signal quality = 0

Operating Mode 5 Status

Solid Green Working normally

Setup

When used as a mobile base station, choose an open area to set up the D-RTK 2 Mobile Station. Mark

the location and align the center of the tripod with the mark to ensure that the D-RTK 2 Mobile Station

can be replaced at the same location.

1. Unfold the tripod, stretch the three retractable legs to the desired length, and then tighten each of the

three knobs. Ensure that the bubble of the bubble level on the mount base is located within the black

circle (viewed from the top of the bubble level vertically) while keeping the tripod secure.

9

EN

• DO NOT change the position or angle of the tripod or the D-RTK 2 Mobile Station after the

tripod has been leveled, or else it should be readjusted.

• The setup environment requires a wild eld of vision. Ensure that there are no obstructions

(trees, buildings) within the zone more than a 15° angel above the horizontal plane of the

D-RTK 2 antenna to prevent the GNSS signals from being absorbed or blocked.

• The setup location should be at least 200 m away from high-power radio emission sources

(such as television stations, microwave stations, etc.) and at least 50 m away from high-

voltage transmission lines to avoid electromagnetic interference to GNSS signals.

• The setup location should be away from large-area waters or objects that strongly interfere

with satellite signal reception to reduce multipath effects.

Usage

The available operating modes vary depending on the products used with the D-RTK 2 Mobile Station.

Select the corresponding operating mode according to the product in use and follow the instructions below.

Instructions

Operating Mode 1/4

1. Lift the extension rod in the tripod to adjust the D-RTK 2 Mobile Station to the desired height and

tighten the sleeve.

2. Power on the D-RTK 2 Mobile Station, wait until system initialization is completed, and enter

Operating Mode 1 or 4.

3. Power on the remote controller and aircraft and make sure that the app is launched.

4. In the app, go to RTK Settings to enable aircraft RTK function. Set the RTK signal source to D-RTK 2

Mobile Station and view the Status display to check the connection. When using a P4 Multispectral

aircraft, tap Connect to establish a connection with the base station.

5. Wait for the system to start searching for satellites. Start the motors when the RTK icon displays FIX or

the status of both the aircraft’s orientation and positioning in the status table in RTK settings show FIX.

During ight, if the D-RTK 2 Mobile Station is moved or it is powered off, the aircraft RTK will

switch to GNSS mode and will not enter the RTK FIX status again. Restart the D-RTK 2 Mobile

Station after ight and wait for it to enter the RTK FIX status.

10

EN

Operating Mode 3

1. Power on the D-RTK 2 Mobile Station, wait until system initialization is completed, and enter

Operating Mode 3.

2. Power on the remote controller and make sure that the app is launched. Check the home screen to

make sure the handheld mapping device is connected.

3. In RTK Settings, select the RTK signal source for the handheld mapping device. Make sure that the

D-RTK 2 Mobile Station used as a handheld mapping device is connected to another D-RTK 2 Mobile

Station used as a base station or a Network RTK server.

4. Set the planning method to handheld RTK for operation planning.

Operating Mode 5

1. Power on the D-RTK 2 Mobile Station, wait until system initialization is completed, and enter

Operating Mode 5.

2. Make sure that the remote controller is connected to the broadcast network of the D-RTK 2 Mobile

Station.

3. Wait for the system to start searching for satellites. Start the motors when the status of both the

aircraft’s orientation and positioning in the status table in RTK settings show FIX.

Advanced Settings

Operating Mode 1/3/4

1. Go to the bottom of RTK Settings and tap Advanced Settings.

2. The settings vary depending on the product used with the D-RTK 2 Mobile Station. Settings include

managing the list of linked remote controllers and viewing and editing the device name.

3. Input measured coordinates and altitude* to set them to the D-RTK 2 Mobile Station when using as a

base station.

Operating Mode 5

1. Go to the bottom of RTK Settings and tap Advanced Settings. Input the administrator password to

enter conguration. The default password is 123456.

2. Edit the name of the mobile station and change the password.

3. Input measured coordinates and altitude* to set them to the D-RTK 2 Mobile Station when using as a

base station.

4. The password can be reset by following the instructions below. Press and hold the Link button on the

mobile station for three seconds, and then press the Operating Mode button once. The Operating

Mode Indicator turns from red to green, indicating that the password has been reset successfully.

* If coordinates input into the app are more than 50 m (for Operating Mode 1) or 15 m (for Operating Mode 4 or 5)

away from the actual coordinates of the D-RTK 2 Mobile Station, they will not be imported.

If the D-RTK 2 Mobile Station is restarted after input coordinates are successfully set, these coordinates will be

used only if the difference between the actual coordinates and the set coordinates is less than 5 m. Otherwise, the

actual positioning coordinates will be used.

Appendix

Specifications

GNSS Receiver GNSS Frequency

Simultaneously receive:

GPS: L1, L2, L5; BeiDou: B1, B2, B3

GLONASS: F1, F2; Galileo: E1, E5A, E5B

11

EN

GNSS Receiver

Positioning Accuracy

Single Point

Horizontal: 1.5 m (RMS)

Vertical: 3.0 m (RMS)

RTK

Horizontal: 1 cm + 1 ppm (RMS)

Vertical: 2 cm + 1 ppm (RMS)

1 ppm: For every 1 km increase in distance, the

accuracy will be 1 mm less. For example, the

horizontal accuracy is 1.1 cm when the receiving end

is 1 km away from the base station.

Positioning Update Rate 1 Hz, 2 Hz, 5 Hz, 10 Hz and 20 Hz

Cold Start < 45 s

Hot Start < 10 s

Recapture Time < 1 s

Initialization Reliability > 99.9%

Differential Data Format RTCM 2.x/3.x

Communication

and Data Storage

Data Link OcuSync, LAN, 4G, Wi-Fi

Operating Frequency 2.4000-2.4835 GHz, 5.725-5.850 GHz

EIRP

OcuSync

2.4 GHz

SRRC/CE/MIC/KCC: < 20 dBm

FCC/NCC: < 26 dBm

5.8 GHz

SRRC/NCC/FCC: < 26 dBm; CE: < 14 dBm

Wi-Fi

2.4 GHz

SRRC/CE/MIC/KCC: < 20 dBm

FCC/NCC: < 22 dBm

5.8 GHz

SRRC/NCC/FCC: < 22 dBm

OcuSync Communication

Distance

Operating Mode 1/3

SRRC/NCC/FCC/MIC/KCC/CE: 2 km

(Unobstructed and free of interference, when the D-RTK

2 Mobile Station is used as a base station and the

distance from the D-RTK 2 antenna to the bottom of the

tripod is 1.8 m, when the difference in height between

the remote controller and D-RTK 2 is less than 2 m, and

when the remote controller is 1.2 m from ground level)

Operating Mode 4

Between the aircraft and mobile station:

NCC/FCC: 7 km; SRRC/MIC/KCC/CE: 5 km

Between the remote controller and mobile station: 200 m

(Unobstructed and free of interference at a ying altitude

of about 120 m, when the distance from the D-RTK 2

antenna to the bottom of the tripod is 1.8 m, and when

the remote controller is 1.2 m from ground level)

Operating Mode 5

NCC/FCC: 12 km; SRRC/MIC/KCC/CE: 6 km

(Unobstructed and free of interference, when the

distance from the D-RTK 2 antenna to the bottom of the

tripod is 1.8 m)

Memory Capacity 16 GB

12

EN

This content is subject to change.

Download the latest version from

http://www.dji.com/d-rtk-2

IMU Features

Built-in high-precision 6-axis accelerometer

D-RTK 2 movement monitoring

Sloping measurements

Electronic bubble level

Electrical

Characteristics

Power Consumption 12 W

Power Supply 16.5 to 58.8VDC

Battery

Type: Lithium-ion battery

Capacity: 4920 mAh

Energy: 37.3 WH

Run Time WB37 battery: > 2 h

Physical

Characteristics

Dimensions (D-RTK 2

body with extension rod) 168 mm × 168 mm × 1800 mm

IP Rating IP65

Operating

Temperature -4° to 131° F (-20° to 55° C)

Updating the Firmware

Update the D-RTK 2 rmware in the DJI Assistant 2 software or the app*. The following instructions use

the DJI Assistant 2 software for example.

1. Turn on the D-RTK 2 Mobile Station.

2. Connect the D-RTK 2 Mobile Station to the computer via the USB-C cable.

3. Launch DJI Assistant 2 and login with a DJI account.

4. Click D-RTK 2 and then click the rmware update tag.

5. Select the desired rmware version.

6. DJI Assistant 2 will download and update the rmware automatically.

* An app version that supports rmware update is required.

Accessories Usage

Power Adapter Cable

Connect the Power Adapter Cable to the external power port, then connect the Power Adapter to a

power outlet (100-240V, 50/60Hz) with the AC power cable.

CHS

13

免责声明

感谢您购买 D-RTKTM 2 高精度 GNSS 移动站（简称 D-RTK 2 移动站）。在使用之前，请仔细阅

读本声明，一旦使用，即被视为对本声明全部内容的认可和接受。请严格遵守本文安装和使用该

产品，并务必重视注意事项。因用户不当使用、安装、改装（包含但不限于使用非 DJI 指定的零

配件）造成的任何损失，深圳市大疆 TM 创新科技有限公司及其关联公司将不承担任何责任。

DJITM 是深圳市大疆创新科技有限公司及其关联公司的商标。本文出现的产品名称、品牌等，均

许可，不得以任何形式复制翻印。

关于不同语言版本的免责声明可能存在的语义差异，中国以中文版为准，其他地区以英文版为准。

注意事项

1. 为提高电池使用寿命，关闭 D-RTK 2 移动站后，请及时取出其中的智能电池。

2. 根据当地无线电规定，使用对应频段的 D-RTK 2 移动站，并遵守当地无线电法律法规。

3. 安装时切勿过度弯曲和折叠线材。

4. 安装和摆放时，务必确保 D-RTK 2 移动站与水平面相对水平。

5. 在开阔、不受无线电干扰的环境中使用 D-RTK 2 移动站。务必在关闭其他同频段的无线设备（如

对讲机等）后再使用。

6. 使用过程中请确保所有设备的天线均不受遮挡。

7. 使用原厂配件或经过 DJI 认证的配件。使用非原厂配件有可能对系统的安全使用造成危险。

8. 确保部件内部没有进入任何异物（如：水、油等液体，沙土等）。

9. 切勿自行拆下出厂时已安装的任何部件。

10. 延长杆底部及三脚架底部较为尖锐，使用时务必小心。

11. 雨雪天气时使用，请对 D-RTK 2 移动站和电池采取必要的防水措施。雷电天气请谨慎使用，

注意防雷。

简介

D-RTK 2 高精度 GNSS 移动站是一款高精度卫星信号接收机，支持 GPS、BEIDOU、 GLONASS

和Galileo 4 系统 11 频*的卫星信号接收，同时内置 OCUSYNCTM 链路，提供流畅稳定的数据传输。

D-RTK 2 移动站可作为 RTK 移动基站，将装备有 DJI RTK 定位系统的飞行器（如 DJI INSPIRETM 3，

大疆农业无人飞机 T50、T25、T40、T20P、T30、T10、T20、T16、MG-1P RTK，PHANTOMTM

4 RTK，P4 Multispectral，MATRICETM 350 RTK、Matrice 30、Matrice 30T、Matrice 300 RTK、

Matrice 210 RTK V2 等）定位精度由米级提升至厘米级，而且提供强大的抗磁干扰能力，在高压线、

金属建筑等强磁干扰的环境下保障可靠的作业飞行。D-RTK 2 移动站作为手持测绘杆，用于手持

测绘、工程放样等其他用途，可实现更加精准的定点测量。

* 详见规格参数。

CHS

14

物品清单

D-RTK 2 主体延长杆×1×1充电管家（USB-C） ×1

智能电池（WB37）电池盖×2×165W 便携充电器 *×1

内六角扳手 ×1USB-C 线 ×1×1USB-C OTG 线

可选配件

连接至交流电源提供长时间供电。

作为移动基站使用时，用于固定 D-RTK 2 主体。

电源适配器转接线电源适配器 AC 电源线

三脚架

* 根据产品发售地区有所不同，具体版本和数量以实物为准。

CHS

15

部件说明

D-RTK 2 主体三脚架

1. 天线

2. 对频按键及指示灯

3. 电源按键及指示灯

4. 模式按键及指示灯

5. USB-C 接口

6. 盘齿

7. 电池仓

8. 电池盖

9. 锁定螺母

10. 外部电源接口 *

1. 套筒

2. 基座

3. 伸缩杆

4. 旋钮

1

1234

5

6

7

8

9

2

3

4

10

底视图

* 配备保护盖，接口使用时取下保护盖并保存好；接口未使用时请盖好保护盖以防水防尘。

文中图示可能与实物存在细微差别，请以实物为准。

CHS

16

准备

充电

短按一次电池的电量按键，可查看电池电量。首次使用时，务必将电池充满。

1. 将电池插入到底，直至听到“咔”的一声，然后将充电器插入充电管家的电源接口，再连接

至交流电源 (100-240 V，50/60 Hz)。

2. 充电管家将按照剩余电量从高至低的顺序依次进行充电。电池充电完成后对应的状态指示灯

变为常亮，请及时将电池从充电管家取出。

参考《WB37 充电管家（USB-C）使用说明》和《WB37 智能电池安全使用指引》，了

解更多内容。

安装电池

开启 / 关闭 D-RTK 2 移动站

长按电源按键以开启 / 关闭 D-RTK 2 移动站。

电源按键

CHS

17

电源指示灯说明

红灯常亮正在初始化 /错误报警

红灯快闪电量 <20%

红灯慢闪接收卫星数量 ≤5 颗

黄灯常亮接收卫星数量 6-9 颗

绿灯常亮接收卫星数量 ≥10 颗

选择工作模式

D-RTK 2 移动站共有 5种工作模式，可配合不同产品使用。按照以下说明进行模式切换。

1. 长按模式按键 2秒，模式状态指示灯由绿色变为黄色，进入模式修改状态。

2. 短按模式按键切换工作模式，修改后等待 2秒进入该模式，指示灯由黄色变为绿色。指示灯

周期内循环闪烁的次数表示不同的工作模式，详见下表。

3. 若进入模式修改状态后无操作，则 2秒后自动退出并维持原模式。

模式名称及适配产品闪灯

工作模式 1移动基站（T20 / T16 / MG-1P RTK / Phantom 4 RTK / P4 Multispectral）1次

工作模式 2预留 2次

工作模式 3手持测绘杆（T20 / T16 / MG-1P RTK / Phantom 4 RTK）3次

工作模式 4移动基站（M210 RTK V2）4次

工作模式 5移动基站（广播模式，Inspire 3 / M350 RTK / M30 / M30T / M300 RTK /

T50 / T25 / T40 / T20P / T30 / T10）5次

使用

D-RTK 2 移动站配合不同产品使用时，操作方法类似。如无特殊说明，以下内容适用于对应工作模式的所

有适配产品。

连接遥控器或飞行器

连接方法

不同工作模式下的连接方法有所不同，具体操作如下。

工作模式 1

配合 T20 / T16 / MG-1P RTK / Phantom 4 RTK 使用

D-RTK 2 移动站需要在 App 中与遥控器对频，下面以大疆农业 App 为例进行说明。

1. 开启 D-RTK 2 移动站电源，等待系统完成初始化，切换到工作模式 1。

2. 打开遥控器，确保显示设备已运行大疆农业 App。

3. 点击“执行作业”进入作业界面，点击 > RTK，打开“飞行器 RTK 定位”。选择 RTK 信

号源为“D-RTK 2 移动站”，然后点击“对频”。遥控器状态指示灯蓝色闪烁，并且发出“滴

滴”提示音，表示进入对频状态。

4. 短按一次 D-RTK 2 移动站上的对频按键，对频状态指示灯红绿交替闪烁表示进入对频状态。

5. 对频成功，遥控器指示灯绿灯常亮，D-RTK 2 移动站指示灯显示当前工作模式下的状态，详

见下表。

6. 遥控器与 D-RTK 2 移动站对频成功后，需要重新与飞行器对频。有以下三种方式：

CHS

18

• 与D-RTK 2 移动站对频完成后，在弹出的窗口中点击“与飞行器对频”，进入与飞行器对

频的状态，按下飞行器对频按键以完成对频。

• 在“RTK 设置”页面，点击飞行器未连接提示旁边的按钮，在弹出的窗口中点击“与

飞行器对频”，进入与飞行器对频的状态。

• 在“遥控器设置”页面进行与飞行器的对频。完成对频后，需在“RTK 设置”页面 D-RTK

2移动站状态处点击“尝试重连”重新连接 D-RTK 2，并确保状态为“连接成功”，否则

将无法使用 RTK 功能。

配合 P4 Multispectral 使用

1. 开启 D-RTK 2 移动站电源，等待系统完成初始化，切换到工作模式 1。

2. 开启遥控器，确保已运行 DJI GS Pro App。

3. 进入 DJI GS Pro 任务界面，点击上方的或RTK 图标进入 RTK 设置菜单，选择 D-RTK 2

作为 RTK 信号源，然后开启菜单底部的飞行器 RTK 开关，否则飞行器将无法使用 RTK 数据。

4. 点击“对频”，遥控器发出“嘀嘀”提示音后按下基站的对频按键。

5. 对频成功，遥控器指示灯绿灯常亮，D-RTK 2 移动站指示灯显示当前工作模式下的状态，详

见下表。

• 当D-RTK 2 移动站已经连接遥控器且遥控器正在控制飞行器作业时，D-RTK 2 移动站

无法与其他遥控器进行对频，请等待飞行器降落并关闭电机后再进行对频。

• 一个 D-RTK 2 移动站最多可与 5个遥控器对频。

工作模式 3

D-RTK 2 移动站需要与遥控器对频后，方可使用。

1. 开启 D-RTK 2 移动站电源，等待系统完成初始化，切换到工作模式 3。

2. 开启遥控器，进入 App 的“遥控器设置”页面，点击“对频”。遥控器状态指示灯蓝灯闪烁，

并且发出“嘀嘀”提示音，表示进入对频状态。

3. 短按一次 D-RTK 2 移动站的对频按键，对频状态指示灯红绿交替闪烁表示进入对频状态。

4. 对频成功，遥控器指示灯绿灯常亮，D-RTK 2 移动站指示灯显示当前工作模式下的状态，详

见下表。

工作模式 4

D-RTK 2 移动站需要与 M210 RTK V2 飞行器对频后，方可使用。

1. 开启 M210 RTK V2 飞行器，并确保已与遥控器对频。

2. 短按一次 D-RTK 2 移动站的对频按键，对频状态指示灯红绿交替闪烁表示进入对频状态。

3. 短按一次飞行器上的对频按键。

4. 等待数秒后，飞行器及移动站的对频状态指示灯均为绿灯常亮，表示对频成功。

工作模式 5

配合 Inspire 3/M350 RTK/M30/M30T/M300 RTK/T50/T25/T40/T20P/T30/T10 使用时，需要遥控

器加入 D-RTK 2 移动站的广播网络中，方可使用。

1. 开启 D-RTK 2 移动站电源，等待系统完成初始化，切换到工作模式 5。

2. 开启遥控器，进入 App 的RTK 设置页面，选择 RTK 信号源为“D-RTK 2 移动站”。

3. 点击 D-RTK 2 移动站状态右侧的，系统将自动进行搜索，在搜索结果列表中选择所需的

RTK 基站，等待连接成功。

CHS

19

对频状态指示灯说明

进入对频状态时，对频状态指示灯将红绿交替闪烁。

退出对频状态时，对频状态指示灯显示如下：

工作模式 1 / 3 / 4 状态

绿灯常亮 OcuSync 信号质量 >70%

绿灯快闪 OcuSync 信号质量 35%-70%

绿灯慢闪 OcuSync 信号质量 ≤ 35%

红灯常亮 OcuSync 信号质量 =0

工作模式 5 状态

绿灯常亮正常工作

架设 D-RTK 2 移动站

作为移动基站使用时，选择视野开阔的地点架设 D-RTK 2 移动站并作标记（使三脚架的中心对准

标记点中心），以便 D-RTK 2 移动站被移动后可以准确复位。

1. 撑开三脚架，将三根伸缩杆拉伸至合适长度，然后拧紧旋钮。确保基座上水平仪中的气泡保

持在黑色圆圈内（从水平仪垂直正上方观察），同时确保三脚架稳固。

2. 安装延长杆至三脚架，拧紧三脚架上的套筒。安装 D-RTK 2 主体至延长杆，拧紧主体上的

锁定螺母。确保 D-RTK 2 移动站上水平仪中的气泡保持在黑色圆圈内（从水平仪垂直正上

方观察）。

La page charge ...

dji Matrice 350 RTK Mode d'emploi

Ce manuel convient également à

dji Matrice 350 RTK Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents