Estate TS25AGXRD02 Manuel utilisateur

Marque: Estate

Modèle: TS25AGXRD02

Catégorie: Frigos

Taper: Manuel utilisateur

Ce manuel convient également à

BYWHIRLPOOLCORPORATION

REFRIGERATORUSE& CARE GUIDE

MANUAL DE USO Y CUIDADO DELREFRIGERADOR

GUIDE D'UTILISATIONETD'ENTRETIENDU

REFRIGERATEUR

Table of Contents / [ndice / Table des mati@res

ASSISTANCE OR SERVICE ............................ 1

REFRIGERATOR SAFETY ............................... 2

INSTALLATION INSTRUCTIONS ................... 3

REFRIGERATOR USE ..................................... 5

REFRIGERATOR CARE ................................... 8

TROUBLESHOOTING ...................................... g

WATER FILTER CERTIFICATIONS .............. 11

PRODUCT DATA SHEETS ............................ 12

WARRANTY .................................................... 13

AYUDA O SERVIClO TF=CNICO .................... 14

SEGURIDAD DEL REFRIGERADOR ............ 14

INSTRUCCIONES DE INSTALACION .......... 15

USO DE SU REFRIGERADOR ...................... 18

CUIDADO DE SU REFRIGERADOR ............. 21

SOLUCION DE PROBLEMAS ....................... 22

HOJA DE DATOS DEL PRODUCTO ............ 25

GARANTiA ...................................................... 26

ASSISTANCE OU SERVICE .......................... 27

SE_CURITF=DU RE:.'FRIGE_RATEUR................ 27

INSTRUCTIONS D'INSTALLATION .............. 28

UTILISATION DU RleFRIGleRATEUR ........... 31

ENTRETIEN DU RleFRIGleRATEUR ............. 34

DlePANNAGE .................................................. 35

FEUILLES DE DONNleES

SUR LE PRODUIT .......................................... 38

GARANTIE ...................................................... 39

AssistanceorService

If you need assistance or service, first see the "Troubleshooting"

section. Additional help is available by calling the Estate Customer

eXperience Center at 1-800-253-1301 from anywhere in the

U.S.A., or write:

Estate Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

Information may also be obtained by visiting our website at

www.estateappliances.com

In Canada, for assistance, installation or service call,

1-800-807-6777, or write:

Whirlpool Canada LP

Customer Interaction Centre

1901 Minnesota Court

Mississauga, Ontario L5N 3A7

In Canada, visit www.estateappliances.ca.

Please include a daytime phone number in your correspondence.

Keep this book and your sales slip together for future

reference. You must provide proof of purchase or installation

date for in-warranty service.

Write down the following information about your appliance to help

you obtain assistance or service if you ever need it. You will need

to know your complete model number and serial number. You can

find this information on the model and serial number label, located

on the inside wall of the refrigerator compartment.

Dealer name

Serial number

Address

Phone number

Model number

Purchase date

Toorder replacement filters, call 1-800-442-9991 and ask for the

part number listed below or contact your authorized Whirlpool

dealer. In Canada, call 1-800-807-6777.

Stainless Steel Cleaner and Polish: Order Part #4396095

Standard Base Filter Cartridge:

Order Part #4392857 (NL300 and L500)

2315225

REFRIGERATORSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

• Plug into a grounded 3 prong outlet.

• Do not remove ground prong.

• Do not use an adapter.

• Do not use an extension cord.

• Disconnect power before servicing.

• Replace all parts and panels before operating.

• Remove doors from your old refrigerator.

• Use nonflammable cleaner.

• Keep flammable materials and vapors, such as gasoline,

away from refrigerator.

• Use two or more people to move and install refrigerator.

• Disconnect power before installing ice maker (on ice maker

kit ready models only).

• Use a sturdy glass when dispensing ice or water (on some

models).

SAVE THESE INSTRUCTIONS

ProperDisposalofYourOld Refrigerator

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can result in death or brain damage.

IMPORTANT: Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are still dangerous

- even if they will sit for "just a few days." Ifyou are getting rid of

your old refrigerator, please follow these instructions to help

prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer:

• Take off the doors.

• Leave the shelves in place so that children may not easily

climb inside.

INSTALLATIONINSTRUCTIONS

[_R_ _¸ _ le _f_i_sf_

Excessive Weight Hazard

Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other injury.

Remove packaging materials. Do not use sharp instruments,

rubbing alcohol, flammable fluids, or abrasive cleaners to remove

tape or glue. These products can damage the surface of your

refrigerator. For more information, see "Refrigerator Safety."

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator

for cleaning or service, be sure to protect the floor.

Always pull the refrigerator straight out when moving it.

Do not wiggle or "walk" the refrigerator when trying to move

it, as floor damage could occur.

NOTE: It is recommended that you do not install the refrigerator

near an oven, radiator, or other heat source. Do not install in a

location where the temperature will fall below 55°F (13°C).

1/2"(1.25 crn)/

II -- i_!

2" (5.08 cm)/

Important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

For your protection, tempered glass is designed to shatter

into many small, pebble-size pieces. This is normal. Glass

shelves and covers are heavy. Use special care when

removing them to avoid impact from dropping.

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

To ensure proper ventilation for your refrigerator, allow for W'

(1.25 cm) space on each side and at the top. When installing your

refrigerator next to a fixed wall, leave 2" (5.08 cm) minimum on

each side (depending on your model) to allow for the door to

swing open. If your refrigerator has an ice maker, allow extra

space at the back for the water line connections.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Before you move your refrigerator into its final location, it is

important to make sure you have the proper electrical connection.

Recommended Grounding Method

A 115 Volt, 60 Hz., AC only 15- or 20-amp fused, grounded

electrical supply is required. It is recommended that a separate

circuit serving only your refrigerator be provided. Use an outlet

that cannot be turned off by a switch. Do not use an

extension cord.

NOTE: Before performing any type of installation, cleaning, or

removing a light bulb, turn the control (Thermostat, Refrigerator or

Freezer Control depending on the model) to OFF and then

disconnect the refrigerator from the electrical source. When you

are finished, reconnect the refrigerator to the electrical source and

reset the control (Thermostat, Refrigerator or Freezer Control

depending on the model) to the desired setting.

,,,_,_,I[91,._=)/ ....... ,+°===,,.......... .......

Gather the required tools and parts before starting installation,

Read and follow the instructions provided with any tools listed

here.

TOOLS NEEDED:

• Flat-blade screwdriver • %" Drill bit

• 7/16"and 1/2"Open-end or two • Hand drill or electric drill

adjustable wrenches (properly grounded)

• 1/4"nut driver

NOTE: Your refrigerator dealer has a kit available with a 1/4"

(6.35 mm) saddle-type shutoff valve, a union, and copper tubing.

Before purchasing, make sure a saddle-type valve complies with

your local plumbing codes. Do not use a piercing-type or 3/16"

(4.76 mm) saddle valve which reduces water flow and clogs more

easily.

IMPORTANT:

• All installations must meet local plumbing code requirements.

• Use copper tubing and check for leaks. Install copper tubing

only in areas where the household temperatures will remain

above freezing.

Water Pressure

A cold water supply with water pressure of between 30 and

120 psi (207 - 827 kPa) is required to operate the water dispenser

and ice maker. Ifyou have questions about your water pressure,

call a licensed, qualified plumber.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the

refrigerator needs to be between 30 and 120 psi (207 - 827 kPa).

If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 - 414 kPa).

If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 - 414 kPa):

• Check to see whether the sediment filter in the reverse

osmosis system is blocked. Replace the filter if necessary.

• Allow the storage tank on the reverse osmosis system to refill

after heavy usage.

• If your refrigerator has a water filter, it may further reduce the

water pressure when used in conjunction with a reverse

osmosis system. Remove the water filter. See "Water Filtration

System."

If you have questions about your water pressure, call a licensed,

qualified plumber.

Read all directions before you begin.

IMPORTANT: If you turn the refrigerator on before the water line is

connected, turn the ice maker OFR

Connect to Water Line

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

3. Locate a 1/2"(12.70 mm) to 11/4'' (3.18 cm) vertical cold water

pipe near the refrigerator.

IMPORTANT:

• Make sure it is a cold water pipe.

• Horizontal pipe will work, but drill on the top side of the

pipe, not the bottom. This will help keep water away from

the drill and normal sediment from collecting in the valve.

Determine the length of copper tubing you need. Measure

from the connection on the lower rear corner of refrigerator to

the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use 1/4"

(6.35 mm) O.D. (outside diameter) copper tubing. Be sure both

ends of copper tubing are cut square.

Using a grounded drill, drill a 1/4"(6.35 mm) hole in the cold

water pipe you have selected.

A. Cold waterpipe E.Compressionsleeve

B.Pipe clamp F.Shutoff valve

C.Copper tubing G.Packing nut

D.Compression nut

6. Fasten the shutoff valve to the cold water pipe with the pipe

clamp. Be sure the outlet end is solidly in the 1/4"(6.35 mm)

drilled hole in the water pipe and that the washer is under the

pipe clamp. Tighten the packing nut. Tighten the pipe clamp

screws slowly and evenly so the washer makes a watertight

seal. Do not overtighten or you may crush the copper tubing.

7. Slip the compression sleeve and compression nut on the

copper tubing as shown. Insert the end of the tubing into the

outlet end squarely as far as it will go. Screw the compression

nut onto outlet end with adjustable wrench. Do not

overtighten.

8. Place the free end of the tubing in a container or sink, and turn

ON the main water supply. Flush the tubing until water is clear.

Turn OFF the shutoff valve on the water pipe. Coil the copper

tubing.

Connect to Refrigerator

Style 1

1. Unplug refrigerator or disconnect power.

2. Attach the copper tube to the valve inlet using a compression

nut and sleeve as shown. Tighten the compression nut. Do not

overtighten.

3. Use the tube clamp on the back of the refrigerator to secure

the tubing to the refrigerator as shown. This will help prevent

damage to the tubing when the refrigerator is pushed back

against the wall.

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any connections (including

connections at the valve) or nuts that leak.

A. Tube clamp

B. Copper tubing

C. Compression nut

D. Valve inlet

The ice maker is equipped with a built-in water strainer. Ifyour

water conditions require a second water strainer, install it in

the 1/4"(6.35 mm) water line at either tube connection. Obtain

a water strainer from your nearest appliance dealer.

Style 2

1. Unplug refrigerator or disconnect power.

2. Remove and discard the shipping tape and the black nylon

plug from the gray, coiled water tubing on the rear of the

refrigerator.

3. If the gray water tube supplied with the refrigerator is not long

enough, a 1/4"x 1/4"coupling is needed in order to connect the

water tubing to an existing household water line. Thread the

provided nut onto the coupling on the end of the copper

tubing.

NOTE: Tighten the nut by hand. Then tighten it with a wrench

two more turns. Do not overtighten.

A B C

A. Refrigerator water tubing

B. Nut (provided)

C. Bulb

D. Coupling (purchased)

Turn shutoff valve ON.

Check for leaks. Tighten any nuts or connections (including

connections at the valve) that leak.

D E F G

E.Ferrule (purchased)

F. Nut (purchased)

G. Household water line

Style 3

1. Unplug refrigerator or disconnect power.

2. Remove and discard the shipping tape and the black nylon

plug from the gray, coiled water tubing on the rear of the

refrigerator.

3. Thread the provided nut onto the water valve as shown.

NOTE: Tighten the nut by hand. Then tighten it with a wrench

two more turns. Do not overtighten.

A.Bulb

B.Nut (provided)

Turn shutoff valve ON.

Check for leaks. Tighten any nuts or connections (including

connections at the valve) that leak.

Complete the Installation

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord,

Failure to follow these instructions can result in death,

fire, or electrical shock.

1. Plug into a grounded 3 prong outlet.

2. Flush the water system. See the "Water and Ice Dispensers"

section.

NOTE: Allow 24 hours to produce the first batch of ice. Allow

3 days to completely fill ice container.

REFRIGERATORUSE

For your convenience, your refrigerator controls are preset at the

factory. When you first install your refrigerator, make sure that the

controls are still preset. The Refrigerator Control and the Freezer

Control should both be set to the "mid-settings."

COLD

FREEZER

COLDER COLD

REFRIGERATOR

IMPORTANT:

• Your product will not cool when the REFRIGERATOR Control

is set to OFR

• The Refrigerator Control adjusts the refrigerator compartment

temperature. The Freezer Control adjusts the freezer

compartment temperature. Settings to the left of the mid-

setting make the temperature less cold. Settings to the right of

the mid-setting make the temperature colder.

• Wait 24 hours before you put food into the refrigerator. If you

add food before the refrigerator has cooled completely, your

food may spoil.

NOTE: Adjusting the Refrigerator and Freezer Controls to a higher

(colder) than recommended setting will not cool the

compartments any faster.

Adjusting Controls

Give the refrigerator time to cool down completely before adding

food. It is best to wait 24 hours before you put food into the

refrigerator. The settings indicated in the previous section should

be correct for normal household refrigerator usage. The controls

are set correctly when milk or juice is as cold as you like and when

ice cream is firm.

If you need to adjust temperatures in the refrigerator or freezer,

use the settings listed in the chart below as a guide. Wait at least

24 hours between adjustments.

CONDITION/REASON: ADJUSTMENT:

REFRIGERATOR too warm REFRIGERATOR Control

one setting higher

FREEZER too warm/ FREEZER Control

too little ice one setting higher

REFRIGERATOR too cold REFRIGERATOR Control

one setting lower

FREEZER too cold FREEZER Control

one setting lower

The control can be adjusted to properly chill meats or vegetables.

The air inside the pan is cooled to prevent "spot" freezing and can

be set to keep meats at the National Livestock and Meat Board

recommended storage temperatures of 28° to 32°F (-2° to 0°C).

The convertible vegetable/meat drawer control comes preset at

the lowest meat setting.

To store meat:

Set the control to one of the three MEAT settings to store meat at

its optimal storage temperature.

To store vegetables:

Set the control to VEG to store vegetables at their optimal storage

temperatures.

NOTE: If food starts to freeze, move the control to the left (less

cold). Remember to wait 24 hours between adjustments.

{on sore® _:_ode s

You can control the amount of humidity in the moisture-sealed

crisper, Adjust the control to any setting between LOW and HIGH,

LOW (open) for best storage of fruits and vegetables with skins.

HIGH (closed) for best storage of fresh, leafy vegetables.

Cut Hazard

Use a sturdy glass when dispensing ice or water.

Failure to do so can result in cuts.

Depending on your model, you may have one or more of the

following options: the ability to select either crushed or cubed ice,

a special light that turns on when you use the dispenser, or a lock

option to avoid unintentional dispensing.

NOTE:

• Do not use with water that is microbiologically unsafe or

of unknown quality without adequate disinfection before

or after the system.

• If your model has a base grille filter system, make sure the

base grille filter is properly installed.

• The dispensing system will not operate when the freezer door

is open.

• After connecting the refrigerator to a water source, flush the

water system by dispensing water into a sturdy container until

you draw and discard 1.5 gal. (5.4 L) of water, or for

approximately 3 minutes after the water begins dispensing.

The flushing process cleans the water system and clears air

from the lines. As the air is cleared from the lines, water may

spurt out of the dispenser.

Allow several hours for the refrigerator to cool down and chill

water.

Allow 24 hours to produce the first batch of ice. Discard the

first three batches of ice produced.

The Water Dispenser

IMPORTANT: Dispense enough water every week to maintain a

fresh supply.

To Dispense Water:

1. Press a sturdy glass against the water dispenser lever.

2. Remove the glass to stop dispensing.

The Ice Dispenser

The dispensing system will not operate when the freezer door is

open. Ice dispenses from the ice maker storage bin in the freezer

when the dispenser lever is pressed.

NOTE: Some models dispense both cubed and crushed ice.

Before dispensing ice, select which type of ice you prefer.

For crushed ice, cubes are crushed before being dispensed. This

may cause a slight delay when dispensing crushed ice. Noise

from the ice crusher is normal, and pieces of ice may vary in size.

When changing from crush to cube, a few ounces of crushed ice

will be dispensed along with the first cubes.

To Dispense Ice:

1. Press the button to select the desired type of ice.

2. Press a sturdy glass against the ice dispenser lever. Hold the

glass close to the dispenser opening so ice does not fall

outside of the glass.

IMPORTANT: You do not need to apply a lot of pressure to the

lever in order to activate the ice dispenser. Pressing hard will

not make the ice dispense faster or in greater quantities.

3. Remove the glass to stop dispensing.

The Dispenser Light

The dispenser area has a light. It can be turned on manually by

pressing the ON button (touchpad or rocker switch).

On some models: Whenever you use the dispenser, the lever will

automatically turn the light on.

LIGHT

OFF ON

NOTE: See the "Changing the Light Bulbs" section for information

on changing the dispenser light bulb.

The Dispenser Lock (on some models)

Your dispenser can be turned off for easy cleaning or to prevent

unintentional dispensing by small children and pets.

NOTE: The lock feature does not shut off power to the product, to

the ice maker, or to the dispenser light. It simply deactivates the

dispenser levers. The ice and water dispensers will not work.

• Press the LOCK button to lock the dispenser.

• Press and hold the LOCK OUT button a second time to unlock

the dispenser.

Turning the Ice Maker On/Off

To turn ON the ice maker, simply lower the wire shutoff arm.

To manually turn off the ice maker, lift the wire shutoff arm to the

OFF (arm up) position and listen for the click.

NOTE: Your ice maker has an automatic shutoff. As ice is made,

the ice cubes will fill the ice storage bin, and the ice cubes will

raise the wire shutoff arm to the OFF (arm up) position. Do not

force the wire shutoff arm up or down.

REMEMBER:

• Allow 24 hours to produce the first batch of ice. Discard the

first three batches of ice produced.

• The quality of your ice will be only as good as the quality of the

water supplied to your ice maker. Avoid connecting the ice

maker to a softened water supply. Water softener chemicals

(such as salt) can damage parts of the ice maker and lead to

poor quality ice. If asoftened water supply cannot be avoided,

make sure the water softener is operating properly and is well

maintained.

• Do not use anything sharp to break up the ice in the storage

bin. This can cause damage to the ice container and the

dispenser mechanism.

• Do not store anything on top of or in the ice maker or storage

bin.

Removing and Replacing Ice Storage Bin

1. Pull the covering panel up from the bottom and then slide it

back toward the rear.

2. Lift the wire shutoff arm so it clicks into the OFF (up) position.

Ice can still be dispensed, but no more can be made.

3. Lift up the front of the storage bin and pull it out.

Replace the bin by pushing it in all the way or the dispenser

will not work. Push the wire shutoff arm down to the ON

position to restart ice production. Make sure the door is

closed tightly.

NOTE: Do not use with water that is microbiologically unsafe

or of unknown quality without adequate disinfection before or

after the system.

Water Filter Status Light (on some models)

The water filter status light will help you know when to change

your water filter. The light will change from green to yellow. This

tells you that it is almost time to change the filter. It is

recommended that you replace the water filter when the status

light changes to red OR water flow to your water dispenser or ice

maker decreases noticeably.

After changing the water filter, reset the water filter status light.

The status light will change from red to green when the system is

reset.

Non-indicator Water Filter (on some models)

If your refrigerator does not have the status light, you should

change the water filter every 6 months depending upon your

usage. If the water flow to the water dispenser or ice maker

decreases noticeably before 6 months have passed, replace the

water filter more often.

Using the Dispenser Without the Water Filter

You can run the dispenser without a water filter. Your water will not

be filtered.

1. Remove the water filter.

2. Slide the cap off the end of the filter and replace the cap in the

base grille.

IMPORTANT: Do not discard the cap. It is part of your

refrigerator. Keep the cap to use with the replacement filter.

3. Rotate the cap until it is securely in position.

REFRIGERATORCARE

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

Both the refrigerator and freezer sections defrost automatically.

However, clean both sections about once a month to prevent

odors from building up. Wipe up spills immediately.

IMPORTANT: Because air circulates between both sections, any

odors formed in one section will transfer to the other. You must

thoroughly clean both sections to eliminate odors. To prevent

odor transfer and drying out of food, wrap or cover foods tightly.

To Clean Your Refrigerator:

NOTE: Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, flammable fluids, cleaning waxes,

concentrated detergents, bleaches or cleansers containing

petroleum products on plastic parts, interior and door liners or

gaskets. Do not use paper towels, scouring pads, or other harsh

cleaning tools.

1. Unplug refrigerator or disconnect power.

2. Hand wash, rinse, and dry removable parts and interior

surfaces thoroughly. Use a clean sponge or soft cloth and a

mild detergent in warm water.

3. Wash stainless steel and painted metal exteriors with a clean

sponge or soft cloth and a mild detergent in warm water.

There is no need for routine condenser cleaning in normal

home operating environments. If the environment is

particularly greasy or dusty, or there is significant pet traffic in

the home, the condenser should be cleaned every 2 to

3 months to ensure maximum efficiency.

If you need to clean the condenser:

• Removethe base grille.

• Use a vacuum cleaner with a soft brush to clean the grille,

the open areas behind the grille and the front surface area

of the condenser.

• Replace the base grille when finished.

Plug in refrigerator or reconnect power.

NOTE: Not all bulbs will fit your refrigerator. Be sure to replace the

bulb with one of the same size, shape and wattage. On some

models, the dispenser light requires a heavy duty 10-watt bulb. All

other lights require a 40-watt bulb. Replacement bulbs are

available from your dealer.

1. Unplug refrigerator or disconnect power.

2. Remove light shield when applicable.

NOTE: To clean the light shield, wash it with warm water and

liquid detergent. Rinse and dry the shield well.

3. Remove light bulb and replace with one of the same size,

shape and wattage.

4. Replace light shield when applicable.

5. Plug in refrigerator or reconnect power.

TROUBLESHOOTING

Trythe solutions suggested here first in order to avoid the cost of an unnecessary service call.

The refrigerator will not operate

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

• Power cord unplugged? Plug into a grounded 3 prong outlet,

• Is outlet working? Plug in a lamp to see if the outlet is

working.

• Household fuse blown or circuit breaker tripped? Replace

the fuse or reset the circuit breaker. Ifthe problem continues,

call an electrician.

• Are controls on? Make sure the refrigerator controls are on.

See "Using the Controls."

• New installation? Allow 24 hours following installation for the

refrigerator to cool completely.

NOTE: Adjusting the temperature controls to coldest setting will

net cool either compartment more quickly.

The motor seems to run too much

Your new refrigerator may run longer than your old one due to its

high-efficiency compressor and fans. The unit may run even

longer if the room is warm, a large food load is added, doors are

opened often, or if the doors have been left open.

The refrigerator is noisy

Refrigerator noise has been reduced over the years. Due to this

reduction, you may hear intermittent noises from your new

refrigerator that you did not notice from your old model. Below are

listed some normal sounds with an explanation.

• Buzzing - heard when the water valve opens to fill the ice

maker

• Pulsating - fans/compressor adjusting to optimize

performance

• Rattling - flow of refrigerant, water line, or from items placed

on top of the refrigerator

• Sizzling/Gurgling - water dripping on the heater during

defrost cycle

• Popping - contraction/expansion of inside walls, especially

during initial cool-down

• Water running - may be heard when water melts during the

defrost cycle and runs into the drain pan

• Creaking/Cracking - occurs as ice is being ejected from the

ice maker mold

The doors will not close completely

• Door blocked open? Move food packages away from door.

• Bin or shelf in the way? Push bin or shelf back in the correct

position.

The doors are difficult to open

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

Are the gaskets dirty or sticky? Clean gaskets with mild soap

and warm water.

The lights do not work

Is a light bulb loose in the socket or burned out? See

"Changing the Light Bulbs."

'_ _'_¢_'_ _£_G_C_ ME_ _

Temperature is too warm

• New installation? Allow 24 hours following installation for the

refrigerator to cool completely.

• Door(s} opened often or left open? Allows warm air to enter

refrigerator. Minimize door openings and keep doors fully

closed.

• Large load of food added? Allow several hours for

refrigerator to return to normal temperature.

• Controls set correctly for the surrounding conditions?

Adjust the controls a setting colder. Check temperature in

24 hours. See "Using the Controls."

There is interior moisture buildup

NOTE: Some moisture build-up is normal.

• Humid room? Contributes to moisture build-up.

• Door(s} opened often or left open? Allows humid air to enter

refrigerator. Minimize door openings and keep doors fully

closed.

C@ .....

The ice maker is not producing ice or not enough ice

• Refrigerator connected to a water supply and the supply

shutoff valve turned on? Connect refrigerator to water

supply and turn water shutoff valve fully open.

• Kink in the water source line? A kink in the line can reduce

water flow. Straighten the water source line.

• Ice maker turned on? Make sure wire shutoff arm or switch

(depending on model) is in the ON position.

• New installation? Wait 24 hours after ice maker installation

for ice production to begin. Wait 72 hours for full ice

production.

• Large amount of ice recently removed? Allow 24 hours for

ice maker to produce more ice.

• Ice cube jammed in the ice maker ejector arm?

Remove ice from the ejector arm with a plastic utensil.

• Reverse osmosis water filtration system connected to

your cold water supply? This can decrease water pressure.

See "Water Supply Requirements."

The ice cubes are hollow or small

NOTE: This is an indication of low water pressure.

• Water shutoff valve not fully open? Turn the water shutoff

valve fully open.

• Kink in the water source line? A kink in the line can reduce

water flow. Straighten the water source line.

• Reverse osmosis water filtration system connected to

your cold water supply? This can decrease water pressure.

See "Water Supply Requirements."

• Questions remain regarding water pressure? Call a

licensed, qualified plumber.

Off-taste, odor or gray color in the ice

• New plumbing connections? New plumbing connections

can cause discolored or off-flavored ice.

• Ice stored too long? Discard ice. Wash ice bin. Allow

24 hours for ice maker to make new ice.

• Odor transfer from food? Use airtight, moisture proof

packaging to store food.

• Are there minerals (such as sulfur) in the water? A water

filter may need to be installed to remove the minerals.

• Is there a water filter installed on the refrigerator? Gray or

dark discoloration in ice indicates that the water filtration

system needs additional flushing.

The ice dispenser will not operate properly

• Freezer door closed completely? Close the door firmly. If it

does not close completely, see "The doors will not close

completely."

• Ice bin installed correctly? Be sure the ice bin is firmly in

position.

• New installation? Wait 24 hours after ice maker installation

for ice production to begin. Wait 72 hours for full ice

production.

• Ice stuck in the delivery chute? Use a plastic utensil to clear

the delivery chute.

• Has the wrong ice been added to the bin? Use only cubes

produced by the current ice maker.

• Has the ice melted around the auger (metal spiral} in the

ice bin? Dump the ice cubes and clean the ice bin.

Cut Hazard

Use a sturdy glass when dispensing ice or water.

Failure to do so can result in cuts.

• Is the ice dispenser stalling while dispensing "crushed"

ice? Change the ice button from "crushed" to "cubed." If

cubed ice dispenses correctly, depress the button for

"crushed" ice and begin dispensing again.

• Has the dispenser arm been held in too long? Ice will stop

dispensing when the arm is held in too long. Wait 3 minutes

for dispenser motor to reset before using again.

The water dispenser will not operate properly

• Freezer door closed completely? Close the door firmly. If it

does not close completely, see "The doors will not close

completely."

• Refrigerator connected to a water supply and the supply

shutoff valve turned on? Connect refrigerator to water

supply and turn water shutoff valve fully open,

• Is the water pressure at least 30 psi? The water pressure to

the home determines the flow from the dispenser. See "Water

System Requirements,"

Kink in the home water source line? Straighten the water

source line.

New installation? Flush and fill the water system.

Water filter installed on the refrigerator? The filter may be

clogged or incorrectly installed.

Is a reverse osmosis water filtration system connected to

your cold water supply? See "Water Supply Requirements"

in either the Installation Instructions or the Use & Care Guide,

Water is leaking from the dispenser

NOTE: One or two drops of water after dispensing is normal.

Cut Hazard

Use a sturdy glass when dispensing ice or water.

Failure to do so can result in cuts.

• Glass not being held under the dispenser long enough?

Hold the glass under the dispenser 2 to 3 seconds after

releasing the dispenser lever.

• New installation? Flush the water system. See "Ice and

Water Dispensers."

• Recently changed water filter? Flush the water system. See

"Ice & Water Dispensers."

The dispenser water is not cool enough

NOTE: Water from the dispenser is chilled to only 50°F (10°C).

• New installation? Allow 24 hours after installation for the

water supply to cool completely.

• Recently dispensed large amount of water? Allow 24 hours

for water supply to cool completely.

• Water not been recently dispensed? The first glass of water

may not be cool. Discard the first glass of water.

• Refrigerator connected to a cold water pipe? Make sure

the refrigerator is connected to a cold water pipe, See "Water

Supply Requirements," in either the Installation Instructions or

the Use & Care Guide.

WATERFILTER

CERTIFICATIONS

State of CalilomJa

Department of Health Services

Water Treatment Device

CertificateNmnber

98- 1344

Datelssued: June9. 1998

Tradt,nlark/Model Desif_n alion Reolacement Eleme]_ts

W_-NL300 NL3bu

,Manufacturer: Whlrl_ol Corp

Th_ _at_r treatment de_it'_s) Jist_d on this Certifi_3at e haw nl_ ¢h_ trstlng _quir_ments pursuant to Section

116830 of the Health a}td Salty Cod_ _r th_ foHowlng h _alt h related c_ntaminan_

Microbiological Celltaminants and Turbidity 1 nor_ic/Radlolo_ic_ Contamlnnnts

_onr Lead

Or_ie Con faminant_

None

RatedServiceCapaclty: 300gallons RatedServiceHaw: 05gpm

Do nol u_e _ith _ater that is microbiologically _nsa_ or o[ unkno_ n qu_lit_ _ithout adequ ate di_in_clio_

bd_re or al_er the _ystem.

Slate of Calfli_mia

Department of Heokh Services

Water Treatment Device

CertificateNumber

98- 1343

Dalelssued: Jtllle9 1998

TrademarkJModel Designation Replacement El .......

w_,-L5oo _LO0

Manufacturer: V_hirlpooi C_,_p: { ..... { ....

( ) ;{))({)

Rated Servie_ C_p_clty: 500 g!iii0n_ 7 ! ii_ )i_i))_ iR_ted S_ice Flow: 0 5 gpm

Do not use with w_ter thatismicr obiologlcally_nsa_ o_ of _nK_own quality,without adequate disi_¢tio_

he.re or aRer the _ystem,

PRODUCTDATA SHEETS

Base Grille Water Filtration System

Model WF-NL300/NL30O capacity 300 Gallons (1136 Liters)

Model WF-L500/L5O0 capacity 500 Gallons (1893 Liters)

System tested and certified by NSF International against

ANSl/NSF Standard 53 for the reduction of Lead; and

against Standard ANSl/NSF 42 for the reduction of Taste

and Odor, Ch or ne C ass .

This system has been tested according to ANSl/NSF 42/53 for the reduction of the substances listed below. The concentration of

the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for

water leaving the system, as specified in ANSI/NSF 42/53.

Substance Reduction Min. Required % Average Influent Challenge Max. Effluent Product Min.% Average%

reduction Influent Concentration mg/L Water mg/L Reduction Reduction

mg/L

Chlorine Taste/Odor >_50% 1.9 2.0 mg/L _+10% 0.05 0.05 97.4 97.4

Contaminant Max. Permissible Average Influent Challenge Max. Effluent Product Min.% Average%

Reduction Concentration mg/L Influent Concentration mg/L Water mg/L Reduction Reduction

mg/L

Lead: (-®pH 6.5 0.01 0.15 0.15 mg/L _+10% 0.001 0.001 99.30 99.30

Lead: @ pH 8.5 0.01 0.15 0.15 mg/L _+10% 0.003 0.001 97.90 99.00

Test Parameters: pH = 7.5 + 0.5 unless otherwise noted. Flow = 0.5 gpm (1.9 Lpm). Pressure = 60 psig (413.7 kPa). Temp. = 63°F

(17.2°C).

• It is essential that operational, maintenance, and filter

replacement requirements be carried out for the product to

perform as advertised.

• Model WF-NL300: The concentration of the indicated

substances in water entering the system was reduced to a

concentration less than or equal to the permissible limit for

water leaving the system as specified in ANSI/NSF 42 and 53.

Change cartridge at least every 6 months. Use replacement

cartridge NL 300, part #4396508. 2005 suggested retail price

of $32.99 U.S.A./S44.95 Canada. Prices are subject to change

without notice.

• Model WF-L500: The concentration of the indicated

substances in water entering the system was reduced to a

concentration less than or equal to the permissible limit for

water leaving the system as specified in ANSl/NSF 42 and 53.

The filter monitor system measures the amount of water that

passes through the filter and alerts you to replace the filter.

When 90% of the filter's rated life is used, the filter indicator

light changes from green to yellow. When 100% of the filter's

rated life is used, the filter indicator light changes from yellow

to red, and it is recommended that you replace the filter. Use

replacement cartridge L500, part #4396508. 2005 suggested

retail price of $32.99 U.S.A./S44.95 Canada. Prices are

subject to change without notice.

• The product is for cold water use only.

• Do not use with water that is microbiologically unsafe or of

unknown quality without adequate disinfection before or after

the system.

• Refer to the "Assistance or Service" section for parts and

service availability or for the Manufacturer's name, address

and telephone number.

• Refer to the "Warranty" section for the Manufacturer's limited

warranty.

• Note that while the testing was performed under standard

laboratory conditions, actual performance may vary. Systems

must be installed and operated in accordance with

manufacturer's recommended procedures and guidelines.

Application Guidelines/Water Supply Parameters

WaterPressure 30 - 120 psig (207- 827 kPa)

WaterTemperature 33° - 100°F(0.6° - 37.8°C)

RatedService Flow 0.5 gpm (1.9 Lpm)

(¢ NSF is a registered trademark of NSF International.

WHIRLPOOLCORPORATION MAJOR APPLIANCEWARRANTY

ONE YEAR LIMITED WARRANTY

For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or

furnished with the product, Whirlpool Corporation or Whirlpool Canada LP (hereafter "Whirlpool") will pay for FS_ replacement parts

and repair labor to correct defects in materials or workmanship. Service must be provided by a Whirlpool designated service company.

ITEMS WHIRLPOOL WILL NOT PAY FOR

1. Service calls to correct the installation of your major appliance, to instruct you how to use your major appliance, to replace or repair

house fuses or to correct house wiring or plumbing.

2. Service calls to repair or replace appliance light bulbs, air filters or water filters. Those consumable parts are excluded from warranty

coverage.

3. Repairs when your major appliance is used for other than normal, single-family household use.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in

accordance with electrical or plumbing codes, or use of products not approved by Whirlpool.

5. Any food loss due to refrigerator or freezer product failures.

6. Replacement parts or repair labor costs for units operated outside the United States or Canada.

7. Pickup and delivery. This major appliance is designed to be repaired in the home.

8. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

g. Expenses for travel and transportation for product service in remote locations.

10. The removal and reinstallation of your appliance if it is installed in an inaccessible location or is not installed in accordance with

published installation instructions.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES

CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED

HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,

ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. WHIRLPOOL SHALL NOT BE LIABLE FOR

INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION

OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES

YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE OR PROVINCE

TO PROVINCE.

Outside the 50 United States and Canada, this warranty does not apply. Contact your authorized Whirlpool dealer to determine if

another warranty applies.

If you need service, first see the "Troubleshooting" section of the Use & Care Guide. After checking "Troubleshooting," additional help

can be found by checking the "Assistance or Service" section or by calling Whirlpool. Inthe U.S.A., call 1-800-253-1301. In Canada,

call 1-800-807-6777. 8/05

MANUAL DE USO Y CUIDADO DELREFRIGERADOR

Ayuda o ServicioT( cnico

Si necesita ayuda o servicio tecnico, vea primero la secci6n

"Soluci6n de Problemas". Para obtener asistencia adicional

Ilamenos al 1-800-253-1301 desde cualquier lugar de los EE.UU,,

o escriba a:

Estate Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

Tambien puede obtener informaci6n visitando nuestro sitio web

en www.estateappliances.com.

En CanadA, para recibir asistencia, instalaci6n o servicio, Ilame al

1-800-807-6777 o escriba a:

Whirlpool Canada LP

Customer Interaction Centre

1901 Minnesota Court

Mississauga, Ontario L5N 3A7

En CanadA, visite www.estateappliances.com.

Favor de incluir un nL_merotelef6nico de dia en su

correspondencia.

Guarde este libro y su comprobante de compra juntos para

referencia futura. Usted debera proporcionar evidencia de la

compra o una fecha de instalacibn para obtener servicio bajo

la garantia.

Escriba la siguiente informaci6n acerca de su electrodomestico

para ayudarle a obtener asistencia o servicio tecnico si alguna vez

Ilegara a necesitarlo. Debera tenet a mane el nQmero completo

del modelo y de la serie, Puede encontrar esta informaci6n en la

etiqueta con el nQmero de modelo y de serie que esta ubicada en

la pared interior del compartimiento del refrigerador.

Nombre del distribuidor

Nt_mero de serie

Direcci6n

Nt_mero de tel_fono

Nt_mero del modelo

Fecha de compra

Para pedir filtros de repuesto, Ilame al 1-800-442-9991 y solicite

el nQmero de pieza que se detalla a continuaci6n o p6ngase en

contacto con su distribuidor autorizado de Whirlpool.

Limpiador de Acero Inoxidable: Pida la pieza No. 4396095

Cartucho del filtro de la base estandar: Pida la pieza

No. 4392857 (NL300 and L500)

SEGURIDAD DELREFRIGERADOR

Su seguridad y la seguridad de los demas es muy importante.

Hemos incluido muchos mensajes importantes de seguridad en este manual yen su electrodomestico. Lea y obedezca siempre

todos los mensajes de seguridad.

Este es el sfmbolo de advertencia de seguridad.

Este simbolo le llama la atencion sobre peligros potenciales que pueden ocasionar la muerte o una lesion a

usted y a los demas.

Todos los mensajes de seguridad iran a continuaci6n del simbolo de advertencia de seguridad y de la palabra

"PELIGRO" o "ADVERTENClA". Estas palabras significan:

Si no sigue las instrucciones de inmediato, usted puede

morir o sufrir una lesion grave.

Si no sigue las instrucciones, usted puede morir o sufrir

una lesion grave.

Todos los mensajes de seguridad le diran el peligro potencial, le diran come reducir las posibilidades de sufrir una lesion y Io que

puede suceder si no se siguen las instrucciones.

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

ADVERTENCIA: Para reducir el riesgo de incendio, choque electrico, o lesiones personales al usar su refrigerador siga

estas precauciones basicas:

• No quite la terminal de conexi6n a tierra.

• No use un cable electrico de extensi6n.

• Desconecte el suministro de energ[a antes de darle servicio.

• Vuelva a colocar todos los componentes y paneles antes de

hacerlo funcionar.

• Remueva las puertas de su refrigerador viejo.

• Use un limpiador no inflamable.

• No use un adaptador.

• Mantenga los materiales y vapores inflamables, tales como

gasolina, alejados del refrigerador.

• Use dos o mas personas para mover e instalar el

refrigerador.

• Desconecte el suministro de energ[a antes de instalar la

fabrica de hielo (en aquellos modelos que incluyen el juego

de instalaci6n de la fabrica de hielo).

• Use un vaso resistente para recibir hielo o agua del

despachador (en algunos modelos).

• Conecte a un contacto de pared de conexi6n a tierra de

3 terminales.

CONSERVAR ESTAS INSTRUCCIONES

C6mo deshacerse adecuadamente de

surefrigerador viejo

Peligro de Asfi×ia

Remueva las puertas de su refrigerador viejo.

No seguir esta instruccion puede ocasionar la muerte

o daffo al cerebro.

IMPORTANTE: El atrapamiento y asfixia de niffos no es un

problema del pasado. Los refrigeradores tirados y abandonados

son un peligro, a0n si van a quedar ahi "por unos pocos dias". Si

Ud. esta por deshacerse de su refrigerador viejo, per favor siga

las instrucciones que se dan a continuaci6n para prevenir

accidentes.

Antes de tirar su viejo refrigerador o congelador:

• Saquelas puertas.

• Deje los estantes en su lugar para que los niffos no puedan

meterse con facilidad.

INSTRUCCIONESDE INSTALACION

C6mo mover su refrigerador:

Peligre de Peso E×cesivo

Use dos o mas personas para mover e instalar

el refrigerador,

No seguir esta instrucci6n puede ocasionar una

lesion en la espalda u otto tipo de lesiones.

Quite los materiales de empaque. No use instrumentos filosos,

alcohol para fricciones, liquidos inflamables, o productos de

limpieza abrasivos para eliminar los restos de cinta o goma. Estos

productos pueden daffar la superficie de su refrigerador. Para mas

informaci6n, vea "Seguridad del refrigerador".

Su refrigerador es muy pesado. Cuando mueva su

refrigerador para limpiarlo o darle servicio, proteja el piso.

AI mover el refrigerador, siempre tire directamente hacia

afuera. No menee el refrigerador de lado a lade ni Io haga

"caminar" cuando Io trate de mover ya que podria da_ar

el piso.

Informaci6n importante para saber acerca de los estantes

y tapas de vidrio:

No limpie los estantes y tapas de vidrio con agua caliente

mientras estan fifes. Los estantes y tapas pueden romperse

si se exponen a cambios bruscos de temperatura o impacto,

come seria un golpe brusco. Para su protecci6n, el vidrio

templado se ha diseffado para hacerse afficos. Esto es normal.

Los estantes y tapas de vidrio son muy pesados. Tenga

mucho cuidado al sacarlos para evitar que se daffen al caer.

Peligro de Explosi6n

Mantenga los materiales y vapores inflamables,

tales como gaeolina, alejados del refrigerador.

No seguir esta instrucci6n puede ocasionar la muerte,

explosi6n, o ineendio.

Para asegurar la adecuada ventilaci6n para su refrigerador, deje

un espacio de V2"(1,25 cm) a cada lado y pot encima. Si Ud.

instala el refrigerador pr6ximo a una pared fija, deje como minimo

2" (5,08 cm) a cada lado (dependiendo del modelo) para permitir

que la puerta abra bien. Si su refrigerador tiene una fabrica de

hielo, asegQrese de que haya espacio adicional atrfis para la

conexi6n de la linea de agua.

NOTA: No se recomienda instalar el refrigerador cerca de un

homo, radiador u otra fuente de calor. No instale el refrigerador

cerca una ubicaci6n en la que la temperatura puede bajar de los

55°F (13°C).

I IL_

2" (5,08 cm)

Peligro de Choque Electrico

Conecte a un contaeto de pared de conexi6n a tierra de

3 terminaies.

No quite la terminal de conexi6n a tierra.

No use un adaptadoro

No use un cable el6ctrico de exteneiono

No seguir estas instrueeiones puede oeasionar

la muerte, incendio o choque el6etrieo.

Antes de mover el refrigerador a su ubicaci6n final, es importante

asegurarse de que tiene la conexi6n electrica adecuada.

M6todo de conexibn a tierra recomendado

Se requiere una fuente de energfa electrica de 115 Voltios, 60 Hz.,

CA solamente y con fusibles de 15 6 20 amperios, debidamente

conectada a tierra. Se recomienda que use un circuito separado

s61opara su refrigerador. Use un tomacorriente que no se pueda

apagar con un interruptor. No use un cable electrico de extensi6n.

NOTA: Antes de realizar cualquier tipo de instalaci6n, limpieza o

de quitar un foco de luz, ponga el control (del termostato, del

refrigerador o del congelador dependiendo del modelo) en la

posici6n OFF (Apagado) y luego desconecte el refrigerador de la

fuente de energia. Cuando haya terminado, reconecte el

refrigerador a la fuente de energfa electrica y vuelva a poner el

control (del termostato, del refrigerador o del congelador

dependiendo del modelo) en la posici6n deseada.

t iIe(sLilS/'l'OScie/SLII YI/Ih/I?'O "_ :_

Retina las herramientas y piezas necesarias antes de comenzar la

instalaci6n. Lea y siga las instrucciones provistas con cualquiera

de las herramientas enlistadas aquL

HERRAMIENTAS NECESARIAS:

• Destornillador de hoja plana • Broca de V4"

• Llaves de boca de 7_d'y V2"o • Taladro manual o

dos Ilaves ajustables electrico (debidamente

conectado a tierra)

• Llave para tuercas de V4"

NOTA: El distribuidor de su refrigerador tiene un juego disponible

con una vMvula de cierre tipo montura de _¼"(6,35 mm), una

uni6n y tuberfa de cobre. Antes de comprar, asegQrese que la

vMvula tipo montura cumpla con los c6digos de plomeria de su

Iocalidad. No use una vMvula perforadora o una vMvula de

montura de 3/16"(4,76 mm) que reduce el flujo de agua y se

obstruye con mils facilidad.

IMPORTANTE:

• Todas las instalaciones deben hacerse de acuerdo a los

requerimientos locales de plomena.

• Use tuberias de cobre y revise si hay fugas. Instale tuberia de

cobre s61oen Areas donde la temperatura va a permanecer

pot encima del punto de congelaci6n.

Presibn del agua

Se necesita un suministro de agua fria con presi6n de agua entre

30 y 120 Ibs/pulg _(207 a 827 kPa) para hacer funcionar el

despachador de agua y la fabrica de hielo, Si usted tiene

preguntas acerca de la presi6n de agua, Ilame a un plomero

competente autorizado,

Suministro de agua de 6smosis inversa

IMPORTANTE: La presi6n del suministro de agua que sale de un

sistema de 6smosis inversa y va a la valvula de entrada de agua

del refrigerador necesitara set entre 30 y 120 Ibs/pulg 2(207 a

827 kPa).

Si se conecta un sistema de filtraci6n de agua de 6smosis inversa

al suministro de agua frfa, la presi6n de agua al sistema de

6smosis inversa necesitara set de un minimo de 40 a 60 Ibs/pulg 2

(276 a 414 kPa),

Si la presi6n del agua del sistema de 6smosis inversa es menor de

40 a 60 Ibs/pulg 2 (276 a 414 kPa):

• F[jese si el filtro de sedimentos en el sistema de 6smosis

inversa esta bloqueado y reemplacelo si fuera necesario.

• Deje que se vuelva a Ilenar el tanque de almacenaje del

sistema de 6smosis inversa despues del uso intense.

• Si su refrigerador tiene un filtro de agua, se podra reducir la

presi6n ann mas si se usa en conjunto con un sistema de

6smosis inversa. Quite el filtro de agua; vea "Sistema de

filtraci6n de agua",

Si tiene preguntas acerca de la presi6n del agua, Ilame a un

plomero competente autorizado.

Lea todas las instrucciones antes de comenzar.

IMPORTANTE: Si usa el refrigerador antes de instalar la conexidn

del agua, ponga la fabrica de hielo en la posicidn apagado (OFF).

Conexibn a la linea de agua

1. Desenchufe el refrigerador o desconecte el suministro de

energia.

2. CIERRE el suministro principal de agua, ABRA la Ilave de agua

mas cercana el tiempo suficiente para que la tuberfa de agua

se vacie totalmente,

3. Busque una tuberia vertical de agua frfa de V2"a I_A''

(12,70 mm a 3,18 cm) cercana al refrigerador.

IMPORTANTE:

• Asegt_rese de que sea una tuberia de agua frfa,

• Una tuberia horizontal funcionara, pete taladre per el lade

superior de la tuberia, no por debajo, Esto ayudara a

mantener el agua alejada del taladro. Esto tambien evita

que se junte sedimento normal en la valvula.

Para determinar la Iongitud de la tuberfa de cobre que va a

necesitar, mida desde la conexi6n baja de la parte trasera

inferior del refrigerador hasta la tuberfa de agua. Agregue

7 pies (2,1 m) para permitir la limpieza. Use tuberfa de cobre

de _/4"(6,35 mm) de diametro externo. Asegt]rese que ambos

extremes de la tuberia de cobre esten cortados rectos.

Usando un taladro conectado a tierra, haga un orificio de _A"

(6,35 mm) en la tuberia de agua fria que Ud. eligi6.

G %_a

A, Tuberfade aguafrfa E.Manga de compresidn

B,Abrazaderapara tuberfa F. Vblvulade cierre

C, Tuberfade cobre G.Tuercade presidn

D. Tuercade compresidn

6. Ajuste la valvula de cierre a la tuberia de agua fria con una

abrazadera para tuberfa. Asegt]rese que el extremo de salida

este firmemente insertado en el orificio taladrado de _¼"

(6,35 mm) en la tuberia de agua y que la arandela este per

debajo de la abrazadera para tuberia. Ajuste la tuerca de

presi6n. Apriete los tornillos de la abrazadera para tuberfa

lentamente yen forma pareja de manera que la arandela

provea un cierre hermetico. No apriete demasiado porque se

puede quebrar la tuberia de cobre.

7. Deslice la manga de compresi6n y la tuerca de compresi6n

sobre la tuberfa de cobre como se muestra. Inserte el extremo

de la tuberia en el extremo de salida hasta donde sea posible.

Atornille la tuerca de compresi6n sobre el extreme de salida

con una Ilave ajustable. No apriete demasiado,

8. Coloque el extremo libre de la tuberia dentro de un recipiente

o fregadero, y ABRA la Ilave de agua principal para lavar la

tuberia hasta que el agua salga limpia. CIERRE la valvula de

cierre del agua en la tuberia de agua, Enrolle la tuberfa de

cobre en espiral,

Conexibn al refrigerador

Estilo 1

1. Desenchufe el refrigerador o desconecte el suministro de

energfa.

2. Fije el tubo de cobre a la entrada de la valvula usando una

tuerca de compresi6n y manga de compresi6n como se

muestra. Ajuste la tuerca de compresi6n. No apriete

demasiado.

3. Use la abrazadera para tuberfa en la parte trasera del

refrigerador para afianzar la tuberia al refrigerador segt]n se

muestra, Esto ayudara a evitar da_os a la tuberfa cuando el

refrigerador se empuje contra la pared posterior.

4. ABRA la valvula de cierre,

5. Revise si hay fugas. Ajuste las conexiones (incluso las de la

valvula) o tuercas que tienen fugas.

A. Abrazadera para tuberfa C. Tuerca de compresidn

B. Tuberfa de cobre D. Entrada de la vblvula

La fabrica de hielo esta equipada con un filtro de agua

incorporado. Si las condiciones del agua local requieren un

segundo filtro de agua, se debe instalar en la linea de agua de

1/4"(6,35 mm) en cualquiera de las conexiones de la tuberfa.

Consiga un filtro de agua del distribuidor de

electrodomesticos mas cercano a su domicilio,

Estilo 2

1. Desenchufe el refrigerador o desconecte el suministro de

energia.

2. Quite y deseche la cinta de empaque y el tap6n de nailon

negro de la tuberia gris de agua enrollada en la parte trasera

del refrigerador.

3. Si el tubo de agua gris suministrado con el refrigerador no es

suficientemente largo, se necesita un acoplamiento de

1A"x 1A"para conectar la tuberia de agua a una linea

domestica de agua existente. Enrosque la tuerca provista

sobre el acoplamiento en el extremo de la tuberfa de cobre.

NOTA: Apriete la tuerca a mano. Luego aprietela dos vueltas

con una Ilave de tuercas. No apriete demasiado.

A B C D E F G

A. Tuberfa de agua al D. Acoplamiento (adquirido)

refrigerador E.F_rula (adquirida)

B. Tuerca (provista) E Tuerca (adquirida)

C. Bulbo G.Lfnea de agua de la casa

4. ABRA la valvula de cierre.

5. Revise si hay fugas. Apriete aquellas tuercas o conexiones

que tengan fugas (incluidas las conexiones en la valvula).

Estilo 3

1. Desenchufe el refrigerador o desconecte el suministro de

energfa.

2. Quite y deseche la cinta de empaque y el tap6n de nailon

negro de la tuberia gris de agua enrollada en la parte trasera

del refrigerador.

3. Enrosque la tuerca provista sobre la vMvula de agua como se

muestra.

NOTA: Apriete la tuerca a mano. Luego aprietela dos vueltas

con una Ilave de tuercas. No apriete demasiado.

J/ |

A. Bulbo

B. Tuerca (provista)

ABRA la valvula de cierre.

Revise si hay fugas. Apriete aquellas tuercas o conexiones

que tengan fugas (incluidas las conexiones en la valvula).

Cbmo terminar la instalacibn

Peligro de Choque Electrico

Conecte a un contaeto de pared de conexi6n a tierra de

3 terminales.

No quite la terminal de conexi6n a tierra.

No use un adaptadoro

No use un cable el_ctrico de extenei6no

No seguir estas instrueeiones puede oeasionar

la muerte, incendio o choque eleetrieo.

1. Conecte a un contacto de pared de conexi6n a tierra de

3 terminales.

2. Enjuague el sistema de agua. Vea "Despachadores de agua y

hielo".

NOTA: Deje transcurrir 24 horas para la producci6n de la primera

tanda de hielo. Deje pasar 3 dias para que se Ilene

completamente el recipiente para hielo.

USO DESUREFRIGERADOR

Uso de os c@s' cs,®s

Para su comodidad, los controles de su refrigerador han sido

programados en la fabrica. Cuando instale su refrigerador por

primera vez asegOrese que los controJes tengan la programaci6n

original• El control del refrigerador y el control del congelador

deberian estar en la "posici6n intermedia".

COLD

FREEZER

COLDER

REFRIGERATOR

• 3 4

COLD 1 6 COLDER

IMPORTANTE:

• Su unidad no enfria cuando el control del REFRIGERADOR

esta en la posici6n OFF (Apagado).

• El control del refrigerador ajusta la temperatura del

compartimiento del refrigerador. El control del congelador

ajusta la temperatura del compartimiento del congelador. Los

ajustes hacia la izquierda de la posici6n intermedia hacen que

la temperatura sea menos frfa. Los ajustes hacia la derecha de

la posici6n intermedia hacen que la temperatura sea mas fria.

• Espere 24 horas antes de guardar alimentos en el refrigerador.

Si usted introduce alimentos antes de que el refrigerador se

haya enfriado completamente, los alimentos pueden

descomponerse.

NOTA: Poner los controles del refrigerador y del congelador en un

ajuste mas alto (mas fifo) que el recomendado no enfriara mas

rapido los compartimientos.

Ajuste de los controles

Permita que el refrigerador se enfrie completamente antes de

introducir los alimentos. Lo mejor es esperar 24 horas antes de

guardar alimentos en el refrigerador. Los ajustes indicados en la

secci6n anterior deberian ser los correctos para el use normal del

refrigerador en una casa. Los controles estan ajustados

correctamente cuando la leche o los jugos estan tan fries como

Ud. desea y cuando el helado tiene consistencia firme.

Si necesita regular las temperaturas en el refrigerador o en el

congelador, utilice come gufa los ajustes que se enumeran en la

tabla siguiente. Espere por Io menos 24 horas entre ajustes.

CONDICION/MOTIVO: AJUSTE:

REFRIGERADOR demasiado caliente Control del

REFRIGERADOR

un ajuste mas alto

CONGELADOR demasiado caliente/ Control del

muy poco hielo CONGELADOR

un ajuste mas alto

REFRIGERADOR demasiado frio Control del

REFRIGERADOR

un ajuste mas bajo

CONGELADOR demasiado frio Control del

CONGELADOR

un ajuste mas bajo

Puede ajustarse el control para que enfrie de manera apropiada

las carnes o los vegetales. El aire dentro de la charola se enfrfa

para prevenir que partes de los alimentos se congelen y puede

ajustarse para mantener la came alas temperaturas de

almacenaje recomendadas per el National Livestock and Meat

Board (Consejo Nacional de Ganado y Carnes): 28 ° a 32°F (-2° a

0°C). El control del caj6n convertible para verduras/carne viene

ajustado de fabrica en la posici6n menos frfa para carnes.

Para guardar la came:

Fije el control en uno de los tres ajustes para MEAT (Came), para

guardar la carne en su temperatura ideal de almacenaje.

Para guardar verduras:

Fije el control en VEG (Verduras) para guardar las verduras ensus

temperaturas 6ptimas de almacenaje.

NOTA: Si los alimentos se empiezan a congelar, mueva el control

hacia la izquierda (menos frfo). Recuerde que debe esperar

24 horas entre ajustes.

{_Ss

Usted puede controlar el nivel de humedad en el caj6n hermetico

para verduras. Regule el control a cualquier ajuste entre Bajo

(LOW) y Alto (HIGH).

LOW (bajo - posici6n abierta) para el mejor almacenamiento de

frutas y verduras con cascaras.

HIGH (Alto - posici6n cerrada) para el mejor almacenamiento de

vegetales de hoja frescos.

Peligro de Cortadurae

Use un vaso resietente para recibir hielo o agua del

despachadoro

No seguir esta inetrucci6n puede ocasionar

cortadurae.

Dependiendo de su modelo, su despachador de agua y hielo

puede tenet una o mas de las caracterfsticas siguientes: un grifo

despachador de agua giratorio y una charola extrafble, una luz

especial que se enciende cuando usted utiliza el despachador o

una opci6n de bloqueo para evitar que salga hielo o agua

involuntariamente.

NOTAS:

• No use con agua que no sea microbiol6gicamente segura

o que sea de calidad desconocida sin desinfectarla

adecuadamente antes o despu_s del sistema.

• Si su modelo tiene un sistema de filtro de la rejilla de la base,

aseg@rese de que el filtro de la rejilla de la base este instalado

adecuadamente.

• El sistema de distribuci6n no funcionara cuando la puerta del

congelador este abierta.

• Despues de haber conectado el refrigerador en un suministro

de agua, enjuague el sistema de agua dispensando agua en

un recipiente resistente hasta que haya enjuagado y

descartado 1,5 galones (5,4 L) de agua, o aproximadamente

por 3 minutes despues de que el agua comience a salir. El

agua que usted saca y descarta limpia el sistema y ayuda a

despejar el aire de las Ifneas. A medida que sale aire de las

lineas, es posible que salgan chorros de agua repentinos del

despachador.

• Deje que pasen varias horas para que el refrigerador se enfrie

y pueda enfriar el agua.

• Deje transcurrir 24 horas para la producci6n del primer Iote de

hielo. Deshagase de los tres primeros Iotes de hielo

producidos.

El despachador de agua

IMPORTANTE: Haga salir suficiente agua cada semana para

mantener un suministro fresco.

Para despachar agua:

1. Oprima un vaso contra la barra del despachador de agua.

2. Retire el vase para detener la salida del agua.

El despachador de hielo

El sistema de distribuci6n no funcionara cuando la puerta del

congelador este abierta. El hielo se distribuye del recipiente de

almacenamiento de la fabrica de hielo en el congelador cuando se

presione la barra del despachador.

NOTA: Algunos modelos despachan hielo en cubos y hielo

picado. Antes de sacar hielo, seleccione el tipo de hielo que

desea.

Para obtener hielo picado, el hielo es triturado antes de ser

despachado. Esto puede retrasar un poco la distribuci6n del hielo

picado. El ruido proveniente del triturador de hielo es normal y los

trozos de hielo pueden variar en tama_o. Cuando cambia de la

posici6n de hielo picado a la posici6n de hielo en cubos, caen

unas onzas de hielo picado junto con los primeros cubos.

Para despachar hielo:

1. Oprima el bot6n del tipo de hielo que desee.

2. Oprima con un vaso resistente la barra del despachador de

hielo. Sostenga el vaso junto al orificio del despachador para

que el hielo no caiga fuera del vaso.

IMPORTANTE: No necesita aplicar mucha presi6n a la barra

para activar el despachador de hielo. Oprimir mucho no hara

que el despachador funcione con mas rapidez o produzca

mayor cantidad de hielo.

3. Retire el vaso para detener la salida del hielo.

La luz del despachador

El Area del despachador tiene una luz. Puede encenderse con la

mano oprimiendo el bot6n de ON (encendido) (bot6n tactil o

interruptor oscilante).

En algunos modelos: Cuando usted utilice el despachador, la

barra encendera automaticamente la luz.

LIGHT

OFF ON

NOTA: Para informaci6n sobre c6mo cambiar el foco del

despachador, vea la seccidn "Cdmo cambiar los focos".

El cierre del despachador (en algunos modelos}

Su despachador puede apagarse para facilitar la limpieza o para

evitar que sea activado involuntario por ni_os o animales

domesticos.

NOTA: La funcidn de cierre no interrumpe el flujo electrico al

refrigerador, a la fabrica de hielo o a la luz del despachador.

Unicamente desactiva las barras del despachador.

• Presione el botdn LOCK (cierre) para trabar el despachador.

• Presione y sostenga el bot6n LOCK OUT (Cierre) una segunda

vez para destrabar el despachador.

deFoblqc® ° = "

Para encender y apagar la f&brica de hielo

Para poner a funcionar (ON) la fabrica de hielo, sencillamente baje

el brazo de control de alambre.

Para apagar (OFF) la fabrica de hielo manualmente, levante el

brazo de control de alambre a la posicidn OFF (apagado - brazo

elevado) y escuche el chasquido.

NOTA: Su fabrica de hielo tiene un apagado automatico. A

medida que se produce el hielo, los cubitos de hielo Ilenaran el

dep6sito para hielo y estos levantaran el brazo de control de

alambre a la posici6n de apagado (OFF - brazo elevado). No

fuerce el brazo de control de alambre hacia arriba o hacia abajo.

RECUERDE:

• Deje transcurrir 24 horas para la producci6n del primer Iote de

hielo. Deshagase de los tres primeros Iotes de hielo

producidos.

• La calidad del hielo dependera de la calidad del agua que

suministre a su fabrica de hielo. Evite la conexidn de su

fabrica de hielo a un suministro de agua blanda. Los quimicos

para ablandar el agua (como la sal) pueden da_ar ciertos

componentes de la fabrica de hielo y producir un hielo de muy

baja calidad. Si no se puede evitar el uso de un suministro de

agua blanda, asegQrese de que el ablandador de agua este

funcionando correctamente y que goce de un buen

mantenimiento.

• No use instrumentos afilados para romper el hielo en el

dep6sito. Esto puede da_ar el recipiente de hielo y el

mecanismo de despachado.

• No guarde nada encima ni dentro de la fabrica de hielo ni en el

dep6sito de hielo.

Para quitar y volver a colocar el depbsito de hielo

1. Levante desde abajo el panel que cubre el dep6sito y

deslicelo hacia atras.

2. Eleve el brazo de control de alambre hasta que enganche en

la posici6n OFF (apagado - brazo elevado). AQn se puede

sacar hielo del despachador pero no se puede hacer mas.

3. Levante y jale de la parte delantera del dep6sito de hielo para

sacarlo.

Vuelva a colocar el dep6sito empujandolo hasta el fondo o de

Io contrario el despachador de hielo no funcionar& Empuje el

el brazo de control de alambre hacia abajo a la posici6n ON

(encendido) para reiniciar la producci6n de hielo. Cerci6rese

de que la puerta este bien cerrada.

La page charge ...

Estate TS25AGXRD02 Manuel utilisateur

Marque: Estate

Modèle: TS25AGXRD02

Catégorie: Frigos

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Estate TS25AGXRD02 User manual
español: Estate TS25AGXRD02 Manual de usuario

Documents connexes

Estate TS25AFXKQ05 Le manuel du propriétaire

Estate TS25AGXRD02 Manuel utilisateur

Ce manuel convient également à

Estate TS25AGXRD02 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents