Sollae Systems SIG-5441 Manuel utilisateur

Sollae Systems

https://www.ezTCP.com

4-Port Digital Input I/O Gateway

SIG-5441 User Manual

Version 1.2

SIG-5441 User Manual Ver. 1.2

- 1 -

https://www.ezTCP.com

This symbol, found on your product or on its packaging, indicates that

this product should not be treated as household waste when you wish to

dispose of it. Instead, it should be handed over to an applicable collection

point for the recycling of electrical and electronic equipment. By ensuring

this product is disposed of correctly, you will help prevent potential negative

consequences to the environment and human health, which could otherwise be caused by

inappropriate disposal of this product. The recycling of materials will help to conserve

natural resources. For more detailed information about the recycling of this product,

please contact your local city office, household waste disposal service or the retail

store where you purchased this product.

Note:

This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in which case

the user will be required to correct the interference at his own expense.

SIG-5441 User Manual Ver. 1.2 
 
- 2 - 
https://www.ezTCP.com 
 
Contents 
Overview ....................................................... - 4 - 
1 Introduction ........................................................ - 4 - 
2 Features ............................................................ - 4 - 
3 Specification ....................................................... - 5 - 
4 Interface ........................................................... - 6 - 
4.1 Power .................................................................. - 6 - 
4.2 Ethernet ............................................................... - 7 - 
4.3 Digital Input Port ..................................................... - 7 - 
4.4 LED ................................................................... - 11 - 
4.5 Function Button ....................................................... - 12 - 
4.6 Setup Port ............................................................ - 12 - 
Preparation ................................................... - 13 - 
1 Installing the Setting Tool ........................................ - 13 - 
2 Connecting a Product ............................................... - 13 - 
3 Searching Devices .................................................. - 13 - 
4 Logging in ......................................................... - 13 - 
Settings ...................................................... - 14 - 
1 Network ............................................................ - 14 - 
1.1 Obtain an IP address automatically ..................................... - 14 - 
1.2 Use a Static IP address................................................ - 15 - 
2 General ............................................................ - 16 - 
2.1 Comments .............................................................. - 16 - 
2.2 Digital Input ......................................................... - 17 - 
3 Security ........................................................... - 18 - 
3.1 Password .............................................................. - 18 - 
3.2 Certificate ........................................................... - 18 - 
3.3 spFinder .............................................................. - 18 - 
3.4 Client ID ............................................................. - 19 - 
Management .................................................... - 20 - 
1 Checking Status .................................................... - 20 - 
1.1 Product Information ................................................... - 20 - 
1.2 Communication Status .................................................. - 21 - 
1.3 Timeout ............................................................... - 22 - 
1.4 Copy status ........................................................... - 22 - 
2 Firmware Change .................................................... - 23 - 
2.1 Online Upgrade ........................................................ - 23 - 
2.2 Manual Upgrade ........................................................ - 24 - 
2.3 Remote Upgrade via cloud............................................... - 24 - 
3 Console ............................................................ - 25 - 

SIG-5441 User Manual Ver. 1.2

- 3 -

https://www.ezTCP.com

4.3.1 Output Tab ............................................................ - 25 -

4.3.2 FW Log Tab ............................................................ - 26 -

4.3.3 Timeout ............................................................... - 26 -

4.4 Export/Import Setting Values ....................................... - 27 -

4.5 Factory Reset ...................................................... - 28 -

5 Technical Support and Warranty ................................ - 29 -

5.1 Technical Support .................................................. - 29 -

5.2 Warranty ........................................................... - 29 -

5.2.1 Free Repair Services .................................................. - 29 -

5.2.2 Charged Repair Services................................................ - 29 -

6 Precaution and Exemption from Liability ....................... - 30 -

6.1 Precaution ......................................................... - 30 -

6.2 Exemption from Liability ........................................... - 31 -

6.2.1 English version ....................................................... - 31 -

6.2.2 French version ........................................................ - 32 -

7 Revision History .............................................. - 34 -

SIG-5441 User Manual Ver. 1.2

- 4 -

https://www.ezTCP.com

1 Overview

1.1 Introduction

SIG-5441 is an industrial I/O Gateway connected to Sollae Cloud. It is equipped

with 4 digital input ports and an Ethernet interface. Users can remotely monitor

digital values of sensors/devices connected to this product by using a web browser

on your PC, tablet or smartphone.



This document presents the information related to device only. To connect the

device to Sollae Cloud, see Sollae Cloud User Guide.

1.2 Features

⚫ 4 digital input ports: Wet Contact, Dry Contact, NPN, PNP input

⚫ Digital input port with Up/Down Counter

⚫ Ethernet Interface

⚫ Freely connected to Sollae Cloud via MQTT

⚫ Data is encrypted and securely transmit using TLS 1.2

⚫ Client certificate authentication for devices

⚫ Industrial temperature range (-40℃ ~ +85℃)

SIG-5441 User Manual Ver. 1.2

- 5 -

https://www.ezTCP.com

1.3 Specification

Digital Input

Input Type

Dry Contact / Wet Contact / NPN / PNP

Input Voltage Range

4.5V ~ 25V

Number of Ports

4 ports

Network Physical Interface

Network Interface

10Base-T/100Base-TX Ethernet (RJ45)

Ethernet Speed Auto Sense

1:1 or Cross-over Cable Auto Sense

Software Functions

Protocols

IP, TCP, ICMP, DHCP, mDNS, MQTT, SSL/TLS 1.2

Network Security

Client certificate-based mutual authentication over TLS

1.2

Indicators

LED

MTX, MRX, Di0, Di1, Di2, Di3

Management

spFinder

Configuration and Monitoring Tool

Access Security

Password

Dimension

Size

94mm x 57mm x 23mm

Weight

about 65g

Operating Environment

Input Voltage

DC5V±0.5V

Protection

Reverse Voltage Protection / Surge Protection

Current Consumption

typically, 150mA

Operating Temperature

-40℃ ~ +85℃

Storage Temperature

-40℃ ~ +85℃

Certificate

KC

Registration (KN 32, KN 35)

CE

EMC 2014/30/EU, RoHS 2011/65/EU

FCC

FCC Part 15 Subpart B, Class A

Table 1-1 Specification

SIG-5441 User Manual Ver. 1.2

- 6 -

https://www.ezTCP.com

1.4 Interface

Figure 1-1 Interface

1.4.1 Power

SIG-5441 requires DC5V power supply whose specification is as follows:

Figure 1-2 Power

SIG-5441 User Manual Ver. 1.2

- 7 -

https://www.ezTCP.com

1.4.2 Ethernet

SIG-5441 provides 10/100Mbps Ethernet. The pin assignment is as follows:

Figure 1-3 Ethernet

1.4.3 Digital Input Port

This port is interfaced with a 3.5mm pitch 6-pole terminal block.

Figure 1-4 Digital Input Port

⚫ Port Specification

Division

Value

Number of ports

4

Maximum Input Voltage

DC 25V

Voltage Required for HIGH decision

higher than DC 4.5V

Voltage for LOW decision

lower than DC 1V

Table 1-2 Port Specification

SIG-5441 User Manual Ver. 1.2

- 8 -

https://www.ezTCP.com

⚫ Circuit Diagram of Digital Input

Figure 1-5 Circuit Diagram of Digital Input

⚫ WET contact

Figure 1-6 WET contact

SIG-5441 User Manual Ver. 1.2

- 9 -

https://www.ezTCP.com

⚫ DRY contact

Figure 1-7 DRY contact

⚫ NPN transistor

Figure 1-8 NPN transistor

SIG-5441 User Manual Ver. 1.2

- 10 -

https://www.ezTCP.com

⚫ PNP transistor

Figure 1-9 PNP transistor

SIG-5441 User Manual Ver. 1.2

- 11 -

https://www.ezTCP.com

1.4.4 LED

SIG-5441 provides 8 LEDs.

Figure 1-10 4 LED

LED operations according to each state are as follows:

When the script is running: RUN

When a network is not connected: LINK

When a network is connected: LINK

When a MQTT connection is NOT established: MTX & MRX

When sending data to the cloud: MTX

When receiving data (command) from cloud: MRX

When the input port is LOW: Di0, Di1, Di2 & Di3

When the input port is HIGH: Di0, Di1, Di2 & Di3

SIG-5441 User Manual Ver. 1.2

- 12 -

https://www.ezTCP.com

1.4.5 Function Button

This button is used to implement a factory reset.

1.4.6 Setup Port

This port is used for making a connection with a PC via USB cable.

SIG-5441 User Manual Ver. 1.2

- 13 -

https://www.ezTCP.com

2 Preparation

2.1 Installing the Setting Tool

You need a Windows program which is called spFinder to use this product. Download

the program on our web site and install it on your PC.

Functions of the spFinder are as follows:

⚫ Searching products connected via network and USB

⚫ Setting products

⚫ Monitoring status of products

2.2 Connecting a Product

Connect a product with your PC via a LAN cable or a USB cable. In the case of

using a LAN cable, note that your PC and the product should be on the same local

area network.

2.3 Searching Devices

Run spFinder on your PC and press the search button. If you select the product

found, the setup menu appears on the right.

2.4 Logging in

Before accessing the searched product, you need to log in first. The default ID

and password are as follows:

Division

Default Values

ID

sig-5441

Password

sig-5441

Table 2-1 The default values of ID and password



If you search the product via network and it has the default value for a password,

spFinder automatically processes the login.

SIG-5441 User Manual Ver. 1.2

- 14 -

https://www.ezTCP.com

3 Settings

3.1 Network

3.1.1 Obtain an IP address automatically

This product can automatically obtain an IP address by DHCP. A DHCP server is

required to use this.

Figure 3-1 Obtain an IP address automatically

⚫ Select the [Obtain an IP address automatically].

⚫ Check the [Obtain DNS server address automatically] and click the [Save]

button.

SIG-5441 User Manual Ver. 1.2

- 15 -

https://www.ezTCP.com

3.1.2 Use a Static IP address

You can set a static IP address to this product.

Figure 3-2 Use a static IP address

⚫ Select the [Use static IP address].

⚫ Set the [Local IP address], [Subnet mask], [Gateway IP address] and [DNS IP

address].

⚫ Click the [Save] button.

SIG-5441 User Manual Ver. 1.2

- 16 -

https://www.ezTCP.com

3.2 General

Figure 3-3 General

3.2.1 Comments

This setting is for storing the product description. The maximum setting size of

this item is 32 bytes. We can add information such as: When a device is registered

to the cloud, this field will be used as the default device description on Sollae

Cloud.

SIG-5441 User Manual Ver. 1.2

- 17 -

https://www.ezTCP.com

3.2.2 Digital Input

⚫ Valid Time (Unit: ms)

This item is to set the valid time of input signal. In order for the input

signal to be judged as a valid signal, it must last longer than the time set

in this item. The setting unit is milliseconds; The range is 100 to 30000. The

default value is 100.

⚫ Counter Type

This item is to set the counter type of each port. You can choose one among

three options: Rise (rising edge), Fall (falling edge) and Both (rising edge

or falling edge). The default value is Rise.

⚫ Counter Direction

This item is to set the counter direction: Up (counting up) or Down

(counting down). The default value is Up

⚫ Default Count Value

The value that counter will start after the device booting up.



Valid Time, Counter Type, Counter Direction, and Default Count Value can also be

set via Sollae Cloud after the device is registered under an account.



User Interface and other features configurations can only be set via Sollae Cloud.

SIG-5441 User Manual Ver. 1.2

- 18 -

https://www.ezTCP.com

3.3 Security

Figure 3-4 Security

3.3.1 Password

Both ID and password are required to access this product. Note that changing the

default password to another is highly recommended for security. The password should

be longer than 8 characters.

⚫ Input a password to use to [Password] and [Retype password].

⚫ Click the [Save] button.

3.3.2 Certificate

All TLS certificates were preloaded to the device, please ignore this part.

3.3.3 spFinder

These items are related to spFinder use.

⚫ Local search

If this item is not checked, you will not be able to search for or connect to

the product on your local network. This item can be set only when the product

is connected via USB.

⚫ Network connection

If this item is not checked, the product cannot be searched on the local

network and the product cannot be connected on the local or remote network.

This item can be set only when the product is connected via USB.

SIG-5441 User Manual Ver. 1.2

- 19 -

https://www.ezTCP.com

⚫ Remote access

If this item is checked, the product can be connected from the remote network.

For security, this item is unchecked by default.

3.3.4 Client ID

The Unique ID which is used to register the device under your account in Sollae

Cloud. See more detail on Sollae Cloud.

La page charge ...

Sollae Systems SIG-5441 Manuel utilisateur

Sollae Systems SIG-5441 Manuel utilisateur

dans d''autres langues