Indesit DIFP 36 Le manuel du propriétaire

Marque: Indesit

Modèle: DIFP 36

Catégorie: Lave-vaisselle

Taper: Le manuel du propriétaire

Operating instructions

Contents

Product Fiche, 2

Precautions, advice and Assistance, 3-4

General safety

Disposal

Saving energy and respecting the environment

Assistance

Installation, 5-6

Positioning and levelling

Connecting the water and electricity supplies

Advice regarding the first wash cycle

Technical data

Description of the appliance, 7

Overall view

Control panel

Loading the racks, 8-9

Lower rack

Cutlery basket

Upper rack

Adjusting upper rack

Start-up and use, 10

Starting the dishwasher

Measuring out the detergent

Wash cycles, 11

Table of wash cycles

Special wash cycles and Options, 12

Rinse aid and refined salt, 13

Measuring out the rinse aid

Measuring out the refined salt

Care and maintenance, 14

Shutting off the water and electricity supplies

Cleaning the dishwasher

Preventing unpleasant odours

Cleaning the sprayer arms

Cleaning the water inlet filter

Cleaning the filters

Leaving the machine unused for extended periods

Troubleshooting, 15

English,1

DIFP 68B1

DISHWASHER

Français, 16

Product Fiche

Brand

INDESIT

Model

DIFP 68B1

Rated capacity in standard place settings (1)

Energy efciency class on a scale from A+++ (low consumption) to D (high consumption)

A+

Energy consumption per year in kWh (2)

293.0

Energy consumption of the standard cleaning cycle in kWh

1.03

Power consumption of the off-mode in W

0.5

Power consumption of the left-on mode in W

5.0

Water consumption per year in litres (3)

3080.0

Drying efcacy class on a scale from G (low efcacy) to A (high efcacy)

Programme time for standard cleaning cycle in minutes

190

The duration of the left-on mode in minutes

Noise in dB(A) Re 1pW

Built-in model

Yes

NOTES

1) The information on the label and che relates to the standard cleaning cycle, this programme is suitable to clean normally

soiled tableware and it is the most efcient programme in terms of combined energy and water consumption. The standard

cleaning cycle corresponds to the Eco cycle.

2) Based on 280 standard cleaning cycles using cold water ll and the consumption of the low power modes. Actual energy

consumption depends on how the appliance is used.

3) Based on 280 standard cleaning cycles. Actual water consumption depends on how the appliance is used.

Product fiche

* Only available in selected models.

Precautions, advice and

Assistance

This appliance was designed and

manufactured in compliance with international

safety standards The following information has

been provided for safety reasons and should

therefore be read carefully.

Keep this instruction manual in a safe place for

future reference. If the appliance is sold, given

away or moved, please ensure the manual is kept

with the machine.

Please read these instructions carefully: they

contain important information on installation, use

and safety.

This appliance is designed for domestic use or

similar applications, for example:

- staff kitchen areas in shops, offices and other

work environments;

- farmhouses;

- use by guests in hotels, motels and other

residential settings;

- bed & breakfasts.

General safety

• Theapplianceshouldnotbeoperatedby

people (including children) with reduced

physical, sensory or mental capacities, or by

inexperienced people who are not familiar with

the product, unless supervision or instructions

on how to use it are provided by someone who

assumes responsibility for their safety.

• Anadultmustsupervisechildrenatalltimesto

prevent them from playing with the appliance.

• The appliance was designed for domestic

use inside the home and is not intended for

commercial or industrial use.

• Theappliancemustbeusedbyadultsonlyto

wash domestic crockery in accordance with

the instructions in this manual.

• Theappliancemustnotbeinstalledoutdoors,

even in covered areas. It is extremely dangerous

to leave the machine exposed to rain and

storms.

• Donottouchtheappliancewhenbarefoot.

• Whenunpluggingtheappliancealwayspullthe

plug from the mains socket. Do not pull on the

cable.

• Thewatersupplytapmustbeshutoffandthe

plug should be removed from the electrical

socket before cleaning or maintaining the

appliance.

• Iftheappliancebreaksdown,donotunderany

circumstances touch the internal parts in an

attempt to perform the repair work yourself.

• Donotleanorsitontheopendoorofthe

appliance: this may cause the appliance to

overturn.

•Thedoorshouldnotbeleftopenasitmaycreate

a dangerous obstacle.

• Keepdetergentandrinseaidoutofreachof

children.

• Thepackagingmaterialshouldnotbeusedas

a toy for children.

Disposal

• Disposalofpackagingmaterial:observelocal

legislation so that the packaging may be

reused.

• The European Directive 2012/19/EU relating

toWasteElectricalandElectronicEquipment

(WEEE) states that household appliances

should not be disposed of using the normal

solidurbanwastecycle.Exhaustedappliances

should be collected separately in order to

optimise the re-using and recycling rate of the

materials inside the machine, while preventing

potential damage to the environment and public

health. The crossed-out dustbin symbol is

marked on all products to remind the owners

of their obligations regarding separated waste

collection.

For further information relating to the correct

disposal of household appliances, owners may

contact the relevant public authority or the local

appliance dealer.

Saving energy and respecting the

environment

Saving water and energy

• Onlybeginawashcyclewhenthedishwasher

isfull.Whilewaitingforthedishwashertobe

filled, prevent unpleasant odours using the Soak

cycle

(seeWashcycles)

• Selectawashcyclethatissuitedtothetype

of crockery and to the soil level of the crockery

using the Table of wash cycles:

 -fordisheswithanormalsoillevelusetheEco

washcycle,whichensureslowenergy/water

consumption levels.

- If the load is smaller than usual activate the

Half Load option*

(see Start-up and use).

• Ifyourelectricitysupplycontractgivesdetailsof

electricity-saving time bands, run wash cycles

when electricity prices are lower. The Delayed

Start button *

(see Start-up and use)

helps you

organise the wash cycles accordingly.

Phosphate-free and chlorine-free detergents

containing enzymes

• Westronglyrecommendthatyouusedetergents

that do not contain phosphates or chlorine, as

these products are harmful to the environment.

• Enzymesprovideaparticularlyeffectiveaction

attemperaturesaround50°C.Asaresult

detergentscontainingenzymescanbeusedin

conjunction with low-temperature wash cycles

in order to achieve the same results as a normal

65°Cwashcycle.

•Toavoidwastingdetergent,usetheproduct

in appropriate quantities based on the

manufacturer’s recommendations, the hardness

ofthewater, the soilleveland the quantity

ofcrockerytobe washed. Even if theyare

biodegradable, detergents contain substances

which may alter the balance of nature.

Assistance

Before contacting Assistance:

• Checkwhethertheproblemcanberesolvedusingthe

Troubleshooting guide

(see Troubleshooting).

• Restarttheprogrammetocheckwhethertheproblem

has ceased to exist.

• Ifthe problempersists, contactthe Authorised

Technical Assistance Service.

Never use the services of unauthorised technicians.

Please have the following information to hand:

• Thetypeofmalfunction.

• Theappliancemodel(Mod.).

• Theserialnumber(S/N).

This information can be found on the appliance data plate

(see Description of the appliance)

Installation

* Only available in selected models.

If the appliance must be moved at any time, keep it in an

upright position; if absolutely necessary, it may be tilted onto its

back.

Positioning and levelling

1.Remove theappliancefrom allpackagingand checkthat

it has not been damaged during transportation. If it has been

damaged, contact the retailer and do not proceed any further

with the installation process.

2.Arrangethedishwashersothatitssidesorbackpanelarein

contact with the adjacent cabinets or the wall. This appliance

can also be recessed under a single worktop*

(see the Assembly

Instruction sheet.)

3. Position the dishwasher on a level sturdy floor. If the floor

is uneven, the front feet of the appliance should be adjusted

untilitreachesahorizontalposition.Iftheapplianceislevelled

correctly, it will be more stable and much less likely to move or

cause vibrations and noise while it is operating.

4*. To adjust the height of the rear foot, turn the red hexagonal

bushing on the lower central part at the front of the dishwasher

using a hexagonal spanner with an opening of 8 mm. Turn the

spanner in a clockwise direction to increase the height and in an

anticlockwise direction to decrease it

(see Building-in Instruction

sheet attached to the documentation.)

Connecting the water and electricity supplies

Connection to the water and electricity supplies should only

beperformedbyaqualifiedtechnician.

The dishwasher should not stand on the water hoses or

electricity supply cable.

The appliance must be connected to the water supply

network using new hoses.

Neveruseoldorsecondhandhosesets.Donotreusehose

sets from any previously installed dishwasher.

The water inlet and outlet hoses and the electricity supply cable

may be positioned towards the right or the left in order to achieve

the best possible installation.

Connecting the water inlet hose

• Toasuitablecoldwaterconnectionpoint:beforeattaching

the hose, run the water until it is perfectly clear so that any

impurities that may be present in the water do not clog the

appliance; after performing this operation, screw the inlet

hose tightly onto a tap with a ¾ gas threaded connection.

• Toasuitablehotwaterconnectionpoint:yourdishwasher

may be supplied with hot water from the mains supply (if you

have a central heating system with radiators) provided that it

doesnotexceedatemperatureof60°C.

Screw the hose to the tap as described for connection to a

cold water supply.

If the inlet hose is not long enough, contact a specialist store

or an authorised technician

(see Assistance.)

The water pressure must be within the values indicated in

the Technical Data table

(see adjacent information.)

The hose should not be bent or compressed.

Connecting the water outlet hose

Connect the outlet hose (without bending it) to a drain duct with

a minimum diameter of 4 cm.

Theoutlethosemustbeataheightrangingfrom40to80cm

fromthefloor/surfacewherethedishwasherrests(A).

Before connecting the water outlet hose to the sink drain, remove

the plastic plug (B).

Anti-flooding protection

To ensure floods do not occur, the dishwasher:

- is provided with a special system which blocks the water supply

in the event of anomalies or leaks from inside the appliance.

Somemodelsarealsoequippedwiththesupplementarysafety

device New Acqua Stop*, which guarantees anti-flooding

protection even in the event of a supply hose rupture.

WARNING: HAZARDOUS VOLTAGE!

Under no circumstances should the water inlet hose be cut, as

it contains live electrical parts.

Electrical connection

Before inserting the plug into the electrical socket, make sure

that:

• Thesocketisearthedandcomplieswithcurrentregulations.

• thesocketcanwithstandthemaximumloadoftheappliance,

which is indicated on the data plate located on the inside of

the door

(see Description of the appliance);

• Thepowersupplyvoltagefallswithinthevaluesindicatedon

the data plate on the inside of the door.

• Thesocketiscompatiblewiththeplugoftheappliance.If

this is not the case, ask an authorised technician to replace

the plug (

see Assistance

); do not use extension cables or

multiple sockets.

Once the appliance has been installed, the power supply

cable and the electrical socket should be easily accessible.

The cable should not be bent or compressed.

If the power supply cable is damaged, it must be replaced

by the manufacturer or its Technical Assistance Service in order

topreventallpotentialhazards

(see Assistance.)

Anti-condensation strip*

After installing the dishwasher, open the door and stick the

adhesive transparent strip under the wooden shelf in order

to protect it from any condensation which may form.

Advice regarding the first wash cycle

After the installation, remove the stoppers from the racks and the

retaining elastic elements from the upper rack, if any.

Immediately before the fist washing, completely fill the salt

dispenser with water and add only then approximately 1

kg of salt

(seechapterentitledRinseaidandrefinedsalt)

The water may overflow: this is normal and is not a cause

for concern. Select the water hardness value

(see chapter

entitledRinseaidandrefinedsalt).

- After the salt has been

pouredinto the machine,the LOW SALTindicator light*

switches off.

If the salt container is not filled, the water softener and

the heating element may be damaged as a result.

Technical data

Dimensions

width 59,5 cm

height 82 cm

depth 57 cm

Capacity 13 standard place-settings

Water supply pressure

0,05 ÷ 1MPa (0.5 ÷ 10 bar)

7,25 – 145 psi

Power supply voltage See appliance data plate

Total absorbed power See appliance data plate

Fuse See appliance data plate

This dishwasher conforms to the

following European Community

Directives:

-2006/95/EC (Low Voltage)

-2004/108/EC (Electromagnetic

Compatibility)

-2009/125/EC (Comm. Reg.

1016/2010) (Ecodesign)

-97/17/EC (Labelling)

-2012/19/EU Waste Electrical

and Electronic Equipment

(WEEE)

The machine has a buzzer/set of tones

(depending on the

dishwasher model

) to inform the user that a command has

been implemented: power on, cycle end etc.

The symbols/indicator lights/LEDs on the control panel/

display may vary in colour and may have a flashing or fixed

light

(depending on the dishwasher model)

The display provides useful information concerning the type

of wash cycle, drying/wash-cycle phase, remaining time,

temperature etc etc.

* Only available in selected models.

Overall view

Description of the

appliance

***Only in completely built-in models.

* Only available in selected models.

The number and type of wash cycles and options may vary depending on the dishwasher model.

Control panel

1. Upper rack

2. Upper sprayer arm

3. Tip-up dispensers

4. Rackheightadjuster

5. Lower rack

6. Lower sprayer arm

7. Washingfilter

8. Salt dispenser

9. Detergent dispenser, rinse-aid dispenser and

Active Oxygen device*

10. Data plate

11. Control panel***

Select wash cycle button

Salt indicator light

Rinse aid indicator light

Wash cycle number and

remaining time indicator light

Delayed start button

ON-OFF/Reset button

and indicator light

Delayed start indicator light

Loading the racks

Tips

Before loading the racks, remove all food residues from the

crockeryandemptyliquidsfromglassesandcontainers.No

preventive rinsing is needed under running water.

Arrange the crockery so that it is held in place firmly and does

not tip over; and arrange the containers with the openings facing

downwardsand the concave/convex parts placed obliquely,

thus allowing the water to reach every surface and flow freely.

Make sure that the lids, handles, trays and frying pans do not

prevent the sprayer arms from rotating. Place any small items

in the cutlery basket.

Since plastic dishes and non-stick frying pans usually retain more

water drops, their drying will be not so good as that of ceramic

or stainless-steel dishes.

Lightweight items such as plastic containers should be placed

in the upper rack and arranged so that they cannot move.

After loading the appliance, make sure that the sprayer arms

can rotate freely.

Lower rack

The lower rack can hold pans, lids, dishes, salad bowls, cutlery

etc. Large plates and lids should ideally be placed at the sides.

Very soiled dishes and pans should be placed in the lower rack

because in this sector the water sprays are stronger and allow

a higher washing performance.

Several dishwasher models are fitted with tip-up sectors*.

They can be used in a vertical position when arranging dishes

orinahorizontalposition(lower)toloadpansandsaladbowls

easily.

Cutlery basket

Thebasketis equipped with top grilles for improved cutlery

arrangement. The cutlery basket should be positioned only at

the front of the lower rack

Knives and other utensils with sharp edges must be placed

in the cutlery basket with the points facing downwards or they

mustbepositionedhorizontallyinthetip-upcompartmentson

the upper rack

Upper rack

Load this rack with delicate and lightweight crockery such as

glasses, cups, saucers and shallow salad bowls.

Several dishwasher models are fitted with tip-up sectors*.

Theycan be used in a vertical position whenarranging tea/

dessert saucers or in a lower position to load bowls and food

containers.

*Only available in selected models with different numbers and

positions.

* Only available in selected models.

Adjusting the height of the upper rack

In order to make it easier to arrange the crockery, the upper rack

may be moved to a higher or lower position.

The height of the upper rack should be adjusted WHEN THE

RACK IS EMPTY.

NEVER raise or lower the rack on one side only.

IftherackisequippedwithaLift-Up device*

(see figure)

, lift

it up by holding its sides. To restore the lower position, press

the levers (A) at the sides of the rack and follow the rack down.

Unsuitable crockery

• Woodencrockeryandcutlery.

• Delicatedecoratedglasses,artistichandicraftandantique

crockery. Their decorations are not resistant.

• Parts in synthetic material which donot withstandhigh

temperatures.

• Copperandtincrockery.

• Crockerysoiledwithash,wax,lubricatinggreaseorink.

Thecoloursofglassdecorationsandaluminium/silverpiecescan

change and fade during the washing process. Some types of

glass(e.g.crystalobjects)canbecomeopaqueafteranumber

of wash cycles too.

Damage to glass and crockery

Caused by:

• Typeofglassandglassproductionprocess.

• Chemicalcompositionofdetergent.

• Watertemperatureofrinsecycle.

Tips:

• Only use glasses and porcelain guaranteed by the

manufacturer as dishwasher safe.

• Useadelicatedetergentsuitableforcrockery.

• Collectglassesandcutleryfromthedishwasherassoonas

the wash cycle is over.

Theupperrackcanbeadjustedforheightbasedonrequirements:

high position to place bulky crockery in the lower rack and low

positiontomakethemostofthetip-upcompartments/sectors

by creating more space upwards.

Tip-up compartments with adjustable position

The side tip-up compartments can be positioned at three

differentheightstooptimizethearrangementofcrockeryinside

the rack.

Wineglassescanbeplacedsafelyinthetip-upcompartments

by inserting the stem of each glass into the corresponding slots.

Cutlery tray*

Some dishwasher models are fitted with a sliding tray which

can be used to hold serving utensils or small cups. For

optimum washing performance, avoid positioning bulky

crockery directly below the tray.

The cutlery tray can be removed

(see Figure).

Before loading the tray, make

sure the supports are prop-

erly coupled to the upper rack

(see Figure).

Start-up and use

* Only available in selected models.

Starting the dishwasher

1. Turn the water tap on.

2.OpenthedoorandpressON-OFFbutton.

3. Measure out the detergent.

(see adjacent information).

4. Load the racks

(see Loading the racks)

5. Select the wash cycle in accordance with the type of crockery

and its soil level

(see table of wash cycles)

by pressing the P

button.

6. Select the wash options*.

(see Special wash cycles and

options)

7. Start the wash cycle by shutting the door.

8. The end of the wash cycle is indicated by beeps and by the

flashing of the wash cycle number on the display. Open the door,

switchofftheappliancebypressingtheON/OFFbutton,shut

off the water tap and unplug the appliance from the electricity

socket.

9.Waitforafewminutesbeforeremovingthecrockery,inorder

to avoid burns. Unload the racks, beginning with the lower level.

- The machine will switch off automatically during

certain extended periods of inactivity, in order to

minimise electricity consumption.

If the crockery is only lightly soiled or if it has been rinsed

with water before being placed in the dishwasher, reduce the

amount of detergent used accordingly.

Modifying a wash cycle in progress

If a mistake was made during the wash cycle selection process,

it is possible to change the cycle, provided that it has only just

begun: open the door taking care to avoid the escaping steam,

bypressingandholdingtheON/OFFbutton,themachinewill

switchoff.SwitchthemachinebackonusingtheON/OFFbutton

and select the new wash cycle and any options desired; start

the cycle by closing the door.

Adding extra crockery

Withoutswitchingoffthemachine,openthedoor,takingcare

to avoid the escaping steam, and place the crockery inside the

dishwasher. Shut the door and the cycle will begin from the point

at which it was interrupted.

Accidental interruptions

If the door is opened during the wash cycle, or if there is a power

cut, the cycle stops. It starts again from the point at which it

was interrupted once the door has been shut or the electricity

supply is restored.

Measuring out the detergent

A good wash result also depends on the correct

amount of detergent being used. Exceeding the stated

amount does not result in a more effective wash and

increases environmental pollution.

Based on how soiled the items are, the amount can be

adjusted to individual cases using powder or liquid

detergent.

In the case of normally soiled items, use approximately

either 35 gr (powder detergent) or 35 ml (liquid detergent).

If tablets are used, one tablet will be enough.

If the crockery is only lightly soiled or if it has been rinsed

with water before being placed in the dishwasher, reduce

the amount of detergent used accordingly.

For good washing results also follow the instructions shown

on the detergent box.

For further questions please ask the detergent producers'

Advice Offices.

To open the detergent dispenser use the opening device “A”.

Introduce the detergent into the dry dispenser “B” only.

Place the amount of detergent for pre-washing directly

inside the tub.

1.WhenmeasuringoutthedetergentrefertotheTableofwash

cyclestoaddtheproperquantity.CompartmentB comprises

alevelshowing the maximum quantity of liquid or powder

detergent that can be added to each cycle.

2.Removedetergentresiduesfromtheedgesofthedispenser

and close the cover until it clicks.

3. Close the lid of the detergent dispenser by pulling it up until

the closing device is secured in place.

The detergent dispenser automatically opens up at the right time

according to the wash cycle.

If all-in-one detergents are used, we recommend using the TABS

option, because it adjusts the cycle so that the best washing

and drying results are always achieved.

Only use detergent which has been specifically designed

for dishwashers.

DO NOT USE washing-up liquid.

Using excessive detergent may result in foam residue

remaining in the machine after the cycle has ended.

The use of tablets is only recommended for models which

offer the MULTI-FUNCTIONAL TABLETS option.

To achieve the best results from each washing and drying

cycle, powder detergent, liquid rinse aid and salt should

be used.

Wash cycles

The number and type of wash cycles and options may vary depending on the dishwasher model.

Wash-cycledataismeasuredunderlaboratoryconditionsaccordingtoEuropeanStandardEN50242.

Based on the different conditions of use, the wash-cycle duration and data can change.

Wash Cycle Drying Options

Wash Cycle

Duration

Water

Consumption (l/

cycle)

Energy

Consumption

(kWh/cycle)

1. Eco Yes

Delayed start

03:10’ 11 1,03

2. Auto Intensive Yes

Delayed start

02:00’ - 3:10’ 14 - 15,5 1,5 - 1,8

3. Auto Normal Yes

Delayed start

1:30’ - 02:30’ 14,5 - 16 1,2 - 1,35

4. Delicate Yes

Delayed start

01:40’ 11 1,1

5. Rapid 40’ No

Delayed start

00:40’ 9,5 0,9

6. Prewash No

Delayed start

00:12’ 4,5 0,01

7. Half Load Yes

Delayed start

01:20’ 12,0 1,15

8. Extra No

Delayed start

01:00’ 11 n.a.

Instructions on wash-cycle selection and detergent dosage:

1. TheECOwashcycleisthestandardcycletowhichtheenergylabeldatarefers.Itcanbeusedtowashcrockerywithanormal

soil level and is the most efficient cycle in terms of energy and water consumption for this type of crockery.

27gr/ml+6gr/ml**–1Tab

(**Quantity of pre-washing detergent)

2. Heavilysoileddishesandpans(nottobeusedfordelicateitems).30gr/ml–1Tab

3.Normallysoiledpansanddishes.27gr/ml+6gr/ml**–1Tab

4.Cyclefordelicateitems,whicharemoresensitivetohightemperatures30gr/ml–1Tab

5.Fastcycletobeusedforslightlydirtydishes(idealfor2placesettings)25gr/ml–1Tab

6.Pre-washwhileawaitingcompletionoftheloadwiththedishesfromthenextmeal.Nodetergent.

7. Idealcycleforsmallloadsofcrockerywithanormalsoillevel.25gr/ml-1Tab

8. Large crockery.

(Do not use on delicate items)

30gr/ml–1Tab

Standbyconsumption:Left-onmodeconsumption:5,0W-Offmodeconsumption:0.5W

n.a. = non applicable

Special wash cycles and Options

* Only available in selected models.

Notes:

Optimumperformancelevelswhenusingthe“Rapid40’"cycle

can be achieved by respecting the specified number of place

settings.

To reduce consumption, only run the dishwasher when it is full.

Note for Test Laboratories: forinformationoncomparativeEN

testing conditions, please send an email to the following address:

[email protected]

Wash options

If an option is not compatible with the selected wash cycle

(see table of wash cycles), the corresponding LED flashes

rapidly 3 times and beeps will sound.

Delayed start

The start of the wash cycle may be delayed for a

period of time between 1 and 12 hours.

1.Press the DELAYEDSTARTbutton: the corresponding

symbol appears on the display; each time you press the

button,thetime(1h,2h,etc.uptomax.12h)fromthestart

of the selected wash cycle will be increased.

2.Selectthecycleandclosethedoor:thetimerwillbegin

counting down;

3. Once this time has elapsed, the indicator light switches

off and the wash cycle begins.

To adjust the delay time and select a smaller period of time,

presstheDELAYEDSTARTbutton.Tocancelit,pressthe

button repeatedly until the selected delayed start indicator

light switches off. The wash cycle will start automatically as

soon as the door is shut.

The Delayed Start function cannot be set once a wash cycle

has been started.

Wash cycle EXTRA

EXTRAmakesitpossibleto carry out a heavy-duty wash

cycle of large crockery up to a max height of 53cm:

baking pans, oven grids, dripping pans, hob grids, large

saucepans, serving dishes, pizza dishes, stainless-steel

hood filters.

Removetheupperracktoloadbulkycrockery.

Release the two locks (right

and left) and pull out the rack.

Whentheupperrackisfitted,

the locks must be always

closed.

In order for the water to reach the crockery everywhere,

arrange it as shown in the Figure.

The cycle can also be used on large delicate crockery

usingtheoptionExtraLight

(seeWashOptions).

Do not start the dishwasher without the upper rack

using wash cycles other than EXTRA.

To carry out the wash cycle Extra and Extra with the

Light* option pour the detergent directly into the tub

and not into the dispenser.

Rinse aid and refined salt

Only use products which have been specifically designed

for dishwashers.

Do not use table/industrial salt or washing-up liquid.

Follow the instructions given on the packaging.

If using a multi-functional product it is not necessary to add

any rinse aid. However, we recommend that you add salt,

especially if you live in an area where the water is hard or

very hard.

(Follow the instructions given on the packaging).

If you do not add salt or rinse aid, the LOW SALT* and

LOW RINSE AID indicator lights will stay lit.

Measuring out the rinse aid

Rinseaidmakesiteasierforthecrockerytodry,aswaterrunsoff

the surfaces more readily and therefore does not leave streaks

or marks. The rinse aid dispenser should be filled:

• WhentheLOWRINSEAIDindicatorlight* on the control panel

is illuminated, a reserve supply of rinse aid is still available

for1-2cycles;

1. Open the dispenser “D” by pressing and pulling up the tab

on the lid;

2.Carefullyintroducethe rinse aid as far as the maximum

reference notch of the filling space - avoid spilling it. If this

happens, clean the spill immediately with a dry cloth.

3. Press the lid down until you hear a click to close it.

NEVER pour the rinse aid directly into the appliance tub.

Adjusting the amount of rinse aid

If you are not completely satisfied with the drying results, you

mayadjustthequantityofrinseaidused.Switchonandoffthe

dishwasherusingtheON/OFFbutton.PresstheP button three

times.PresstheON/OFFbutton,thesetlevelappearsonthe

display

(set to factory level).

Adjust the rinse aid supply level with the P button.

Press the ON/OFF button to save the adjustment setting.

TherinseaidlevelcanbesettoZERO,insuchacasetherinse

aid will not be supplied and the low rinse aid indicator light in

case of running out.

A maximum of 4 levels can be set according to the dishwasher

model.

•Iftherearestreaksonthecrockery,settoalownumber(1-2).

•Incaseofdropsofwaterorlimescalemarks,settoahigh

number number (3-4).

Setting the water hardness

Everydishwasherisequippedwithawatersoftenerwhich,by

using refined salt designed especially for this type of appliance,

supplies water without limescale which is then used to wash

the crockery.

This dishwasher offers a setting which helps to reduce pollution

and optimises washing performance in accordance with the

water hardness level in your area. This information can be

obtained from your local water supplier.

SwitchonandoffthedishwasherusingtheON/OFFbutton.Press

and hold the P button for a few seconds until you hear a beep.

SwitchonthedishwasherwiththeON/OFFbutton,thesetlevel

appears on the display

(water softener set to medium level).

Adjust the water hardness level with the P button,

(1-2-3-4-5*

see water hardness table)

up to a max. of 5 levels.

Press the ON/OFF button to save the adjustment setting.

Evenifusingmulti-functionaltablets,thesaltdispensershould

still be filled.

(°dH=hardnessmeasuredinGermandegrees-°f=hardness

measuredinFrenchdegrees–mmol/l=millimolesperlitre)

Measuring out the refined salt

In order to obtain the best possible results from a wash cycle,

make sure that the salt dispenser is never empty.

Refinedsaltremoveslimescalefromthewater,thusavoiding

the formation of deposits on crockery.

The salt dispenser is located in the lower part of the dishwasher

(see Description)

and should be filled:

• Whenthegreenfloat* cannot be seen by simply looking at

the cap of the salt dispenser;

• WhentheLOWRINSEAIDindicatorlightonthecontrolpanel

is illuminated *;

1.Removethe lower rack and unscrew

the cap (anticlockwise).

2.Thefirsttimeyoudothis:fillthewater

tank right up to its edge.

3. Position the funnel*

(see figure)

and

fill the salt dispenser up to the edge

(approximately 1 kg). It is normal for a

little water to leak out.

4.Removethefunnel*andwipeanysaltresiduesawayfrom

the opening; rinse the cap under running water and then screw

it on, the head facing downwards so as to let the water flow out

of the four slots (star-shaped arrangement) in the lower part of

the cap (cap with green float*).

It is advisable to perform this procedure every time you add

salt to the dispenser.

Make sure the cap is screwed on tightly so that no detergent can

get into the container during the wash cycle (this could damage

the water softener beyond repair).

Whennecessary,measureoutthesaltbeforeawashcycle

so that any saline solution which has leaked out of the salt

dispenser is removed.

* Only available in selected models.

Water Hardness Table

Average salt dispenser

capacity duration**

level °dH °fH mmol/l months

1 0 - 6 0 - 10 0 - 1 7 months

2 6 - 11 11 - 20 1,1 - 2 5 months

3 12 - 17 21 - 30 2,1 - 3 3 months

4 17 - 34 31 - 60 3,1 - 6 2 months

34 - 50 61 - 90 6,1 - 9 2/3 weeks

For values between 0°f and 10°f, we do not recommend the use of salt.

* a setting of 5 may increase cycle duration.

** 1 wash cycle per day.

Care and maintenance

* Only available in selected models.

Shutting off the water and electricity

supplies

• Turnoffthewatertapaftereverywashcycletoavoidleaks.

• Alwaysunplug the appliance when cleaning itandwhen

performing maintenance work.

Cleaning the dishwasher

• Theexternalsurfacesofthemachineandthecontrolpanel

can be cleaned using a non-abrasive cloth which has been

dampened with water. Do not use solvents or abrasive

products.

• Anymarksontheinsideoftheappliancemayberemoved

using a cloth dampened with water and a little vinegar.

Preventing unpleasant odours

• Alwayskeepthedooroftheapplianceajarinordertoavoid

moisture from forming and being trapped inside the machine.

• Cleanthesealsaroundthedooranddetergentdispensers

regularly using a damp sponge. This will avoid food becoming

trapped in the seals, which is the main cause behind the

formation of unpleasant odours.

Cleaning the sprayer arms

Food residue may become encrusted onto the sprayer arms

and block the holes used to spray the water. It is therefore

recommended that you check the arms from time to time and

clean them with a small non-metallic brush.

The two sprayer arms may both be removed.

To remove the upper sprayer arm,

turn the plastic locking ring in an

anti-clockwise direction. The upper

sprayer arm should be replaced

so that the side with the greater

number of holes is facing upwards.

The lower sprayer arm can be

removed by pressing on the side

tabs and pulling it upwards.

Cleaning the water inlet filter*

If the water hoses are new or have not been used for an extended

period of time, let the water run to make sure it is clear and free

of impurities before performing the necessary connections. If this

precaution is not taken, the water inlet could become blocked

and damage the dishwasher.

Clean the water inlet filter at the tap outlet regularly.

- Turn off the water tap.

- Unscrew the end of the water inlet hose, remove the filter and

clean it carefully under running water.

-Re-placethefilterandscrewthewaterhosebackintoposition.

Cleaning the filters

The filter assembly consists of three filters which remove food

residues from the washing water and then recirculate the water.

They should be cleaned if you wish to achieve the best results

in every wash.

Clean the filters regularly.

The dishwasher should not be used without filters or if the

filter is loose.

•Afterseveralwashes,checkthefilterassemblyandifnecessary

clean it thoroughly under running water, using a non-metallic

brush and following the instructions below:

1. Turn the cylindrical filter C in an anti-clockwise direction and

pull it out

(fig. 1).

2.RemovethecupfilterB by exerting a slight pressure on the

side flaps

(fig.2);

3. Slide out the stainless-steel plate filter A.

(fig. 3).

4. Inspect the trap and remove any food residues. NEVER

REMOVE the wash-cycle pump protection

(black detail) (fig.4).

After cleaning the filters, re-place the filter assembly and fix it in

position correctly; this is essential for maintaining the efficient

operation of the dishwasher.

Leaving the machine unused for extended

periods

• Disconnecttheappliancefromtheelectricitysupplyandshut

off the water tap.

• Leavethedooroftheapplianceajar.

• Whenyoureturn,runawashcyclewhenthedishwasheris

empty.

Troubleshooting

Whenevertheappliancefailstowork,checkforasolutionfromthefollowinglistbeforecallingforAssistance.

* Only available in selected models.

Problem: Possible causes / Solutions:

The dishwasher does not start or

cannot be controlled.

• Switch off the appliance by pressing the ON/OFF button, switch it back on after approximately

one minute and reset the program.

• The appliance has not been plugged in properly.

• The dishwasher door has not been shut properly.

The door won’t close. • The lock was released. Strongly push the door until a “clacking” noise is heard.

No water drains out from the

dishwasher.

• The dishwasher cycle has not yet nished.

• The water inlet hose is bent (see Installation).

• The drain duct is blocked.

• The lter is clogged up with food residues.

The dishwasher makes excessive

noise.

• The dishes are rattling against each other or against the sprayer arms.

• Excessive foam presence: the detergent has not been measured out correctly or it is not

suitable for use in dishwashers. (see Start-up and use).

The dishes and glasses are covered

in a white lm or limescale deposits.

• The level of the rened salt is low or the dosage setting is not suited to the hardness of the

water (see Rinse aid and salt).

• The lid on the salt dispenser is not closed properly.

• The rinse aid has been used up or the dosage is too low.

The dishes and glasses are streaked

or have a bluish tinge.

• The rinse aid dosage is too high.

The crockery has not been dried

properly.

• A wash cycle without a drying programme has been selected.

• The rinse aid has been used up or the dosage is too low (see Rinse aid and salt).

• The rinse aid dispenser setting is not high enough.

• The crockery is made from non-stick material or plastic.

The dishes are not clean.

• The racks are overloaded (see Loading the racks).

• The crockery has not been arranged well.

• The sprayer arms cannot move freely.

• The wash cycle is too gentle (see Wash cycles).

• Excessive foam presence: the detergent has not been measured out correctly or it is not

suitable for use in dishwashers. (see Start-up and use).

• The lid on the rinse aid compartment has not been shut correctly.

• The lter is dirty or blocked (see Care and maintenance).

• The rened salt level is low (see Rinse aid and salt).

The dishwasher does not take any

water in - Tap shut-off alarm

(beeps are heard and H appears for

some minutes on the display)

(the ON/OFF indicator light ashes and

number 6 appears on the display).

• There is no water in the mains supply.

• The water inlet hose is bent (see Installation).

• Turn on the tap and the appliance will start after a few minutes.

• The appliance lock has been activated because no action was taken when the beeps sounded.

Switch off the machine using the ON/OFF button, turn on the tap and switch the machine back

on after a few seconds by pressing the same button. Re-program the appliance and restart the

wash cycle.

Mode d’emploi

Sommaire

Fiche de produit, 17

Précautions et conseils, 18-19

Sécurité générale

Mise au rebut

Economies et respect de l’environnement

Service

Installation, 20-21

Mise en place et mise à niveau

Raccordements eau et électricité

Conseils pour le premier lavage

Caractéristiques techniques

Transport

Description de l’appareil, 22

Vue d’ensemble

Tableau de bord

Charger les paniers, 23-24

Panier inférieur

Panier à couverts

Panier supérieur

Clayettes rabattables

Régler la hauteur du panier supérieur

Vaisselle non appropriée

Mise en marche et utilisation, 25

Mettre en marche le lave-vaisselle

Charger le produit de lavage

Programmes, 26

Tableau des programmes

Programmes spéciaux et Options, 27

Produit de rinçage et sel régénérant, 28

Charger le produit de rinçage

Charger le sel régénérant

Entretien et soin, 29

Coupure de l’arrivée d’eau et de courant

Nettoyer le lave-vaisselle

Eviter les mauvaises odeurs

Nettoyer les bras de lavage

Nettoyage du filtre d’entrée d’eau

Nettoyer les filtres

En cas d’absence pendant de longues périodes

Anomalies et remèdes, 30

DIFP 68B1

LAVE-VAISSELLE

Français, 16

Fiche de produit

Marque

INDESIT

Modèle

DIFP 68B1

Capacité nominale dans un environnement standard (1)

Classe énergétique sur une échelle de A+++ (faible consommation) à D (consommation élevée)

A+

Consommation d''énergie par année en kWh (2)

293.0

Consommation d''énergie du cycle de lavage standard en kWh

1.03

Consommation d''energie en mode "off" en W

0.5

Consommation d''energie en mode "on" en W

5.0

Consommation d''eau par an en litres (3)

3080.0

Classe d’efcacité du séchage sur une échelle de G (efcacité minimum) à A (efcacité maximum)

Durée du programme pour un cycle de lavage standard en minutes

190

Durée du mode "on" en minutes

Émissions acoustiques dans l’air, exprimées en dB(A) re 1 pW

Encastrable

Oui

Remarque

1) Les informations sur l’étiquette et sur la che se rapportent au cycle de lavage standard. Ce programme convient pour laver une

vaisselle normalement sale, et il s’agit des programmes les plus efcaces en termes de consommation combinée d’eau et d’énergie. Le

cycle de lavage standard correspond au cycle éco.

2) Sur la base de 280 cycles de lavage standard avec une alimentation en eau froide et une consommation en modes à faible

puissance. La consommation réelle d’énergie dépend des conditions d’utilisation de l’appareil.

3) Sur la base de 280 cycles de lavage standard. La consommation réelle d’énergie dépend des conditions d’utilisation de l’appareil.

Fiche de produit

* Présent uniquement sur certains modèles.

Précautions et conseils

Cet appareil a été conçu et fabriqué

conformément aux normes internationales de

sécurité. Ces consignes sont fournies pour des

raisons de sécurité, il faut les lire attentivement.

Conserver ce mode d’emploi pour pouvoir le

consulter à tout moment. En cas de vente, de

cession ou de déménagement, s’assurer qu’il

accompagne bien l’appareil.

Lire attentivement les instructions : elles fournissent

des conseils importants sur l’installation, l’utilisation

et la sécurité de l’appareil.

Cet appareil est conçu pour un usage domestique

ou autres applications similaires, telles que :

- lieux aménagés en espace cuisine pour le

personnel de magasins, bureaux et autres lieux

de travail ;

- fermes ;

- utilisation par les clients d’hôtels, de motels ou

autres locaux de type résidentiel ;

- chambres d’hôtes.

Sécurité générale

• Cet électroménager n'estpasdestinéàêtre

utilisé par des personnes (enfants compris)

dont les capacités physiques, sensorielles ou

mentales sont réduites ou qui ne disposent

pasdesconnaissancesoudel'expérience

nécessaires, à moins qu'elles n'aient été

forméesetencadréespourl'utilisationdecet

appareil par une personne responsable de leur

sécurité.

• Lesenfantsdoiventêtresurveillésparunadulte

pour éviter qu’ils ne jouent avec l’appareil.

• Cetappareilestconçupourunusagedetype

nonprofessionnelàl'intérieurd'unehabitation.

• Cetappareilestdestinéaulavagedevaisselleà

usagedomestique,ilnedoitêtreutiliséquepar

des adultes et selon les instructions reportées

dans cette notice.

• Nepasinstallerl’appareilàl’extérieur,même

dansunendroitprotégé,carilestextrêmement

dangereux de l’exposer à la pluie et aux orages.

• Nepastoucheraulave-vaissellepiedsnus.

• Nejamaistirersurlecâblepourdébrancherla

fiche de la prise de courant.

• Fermerlerobinetdel’eauetdébrancherlafiche

de la prise de courant avant d’effectuer tous

travaux de nettoyage et d’entretien.

• Encasdepanne,éviteràtoutprixd’accéder

aux mécanismes internes pour tenter une

réparation.

• Nepass’appuyeràlaporteouverteous’y

asseoir : l’appareil pourrait basculer.

• Nepasgarderlaporteouvertepouréviterde

buter contre elle en risquant de se faire mal.

• Garder lesproduitsde lavageetderinçage

hors de la portée des enfants.

• Lesemballagesnesontpasdesjouetspourenfants.

Mise au rebut

• Mise au rebut du matériel d’emballage : se

conformer aux réglementations locales de

manièreàcequelesemballagespuissentêtre

recyclés.

• Ladirectiveeuropéenne2012/19/EUsur

les déchets d’équipements électriques

et électroniques (DEEE), prévoit que les

électroménagers ne peuvent pas être traités

comme des déchets solides urbains normaux.

Lesappareils usagés doivent être collectés

séparément afin d’optimiser le taux de

récupération et le recyclage des matériaux

qui les composent et réduire l’impact sur la

santé humaine et l’environnement Le symbole

de la poubelle barrée est appliqué sur tous les

produits pour rappeler qu’ils font l’objet d’une

collecte sélective.

Pour tout autre renseignement sur la collecte

des électroménagers usés, prière de s’adresser

au service public préposé ou au vendeur.

Economies et respect de l’environnement

Faire des économies d’eau et d’électricité

• Nefairefonctionnerlelave-vaissellequequand

il est rempli au maximum de sa capacité.

Dans l’attente de remplir l’appareil, lancer le

cycle de Trempage pour éviter la formation de

mauvaises odeurs

(voir Programmes)

• Sélectionnerunprogrammeadaptéautypede

vaisselle et à son degré de salissure, consulter

pour cela le Tableau des programmes :

- pour de la vaisselle normalement sale, choisir

le programme Eco (économique), il limite la

quantité d’eau et d’électricité utilisée.

- pour une quantité réduite de vaisselle, choisir

l’option Demi-charge*

(voir Mise en marche et

utilisation).

• Silecontratdefournitured’électricitéprévoit

des tranches horaires à prix réduit, effectuer

les lavages pendant ces heures creuses.

L’option Départ différé*

(voir Mise en marche

et utilisation)

peut vous aider à organiser vos

lavages dans ce sens.

Produits de lavage sans phosphates, sans

chlore et aux enzymes

• Ilestvivementconseilléd’utiliserdesproduits

de lavage sans phosphates et sans chlore, plus

indiqués pour la protection de l’environnement.

•Les enzymes développent une action

particulièrement efficace à des températures

avoisinant50°C,lesproduitsdelavageaux

enzymespermettentdoncdesélectionnerdes

lavages à de basses températures et d’obtenir

lesmêmesrésultatsqu’àunetempératurede

65°C.

• Pour bien doser le produit de lavage,ilfaut

tenir compte des indications du fabricant, de

la dureté de l’eau, de la quantité de vaisselle

et de son degré de salissure pour éviter tout

gaspillage. Bien que biodégradables, les

produits de lavage contiennent des éléments

qui altèrent l’équilibre de la nature.

Avant d’appeler le service d’assistance

technique:

• Vérifiers’il estpossible derésoudre l’anomalie soi-

même

(voir Anomalies et remèdes).

• Faire repartirle programme pours’assurer que

l’inconvénient a été résolu.

• Sicen’estpaslecas,contacterunServiced’Assistance

Technique agréé.

Ne jamais faire appel à des techniciens non agréés.

Communiquer:

• letyped’anomalie;

• lemodèledel’appareil(Mod.);

• lenumérodesérie(S/N).

Ces informations figurent sur la plaque signalétique

apposée sur l’appareil

(voir Description de l’appareil).

Service

* Présent uniquement sur certains modèles.

En cas de déménagement, transporter l’appareil

verticalement; si besoin est, l’incliner sur le dos.

Mise en place et mise à niveau

1.Déballerl’appareilets’assurerqu’iln’apasétéendommagé

pendant le transport. S’il est abîmé, ne pas le raccorder et

contacter le revendeur.

2.Installerlelave-vaisselledemanièreàcequelescôtéset

la paroi arrière touchent aux meubles adjacents ou au mur.

L’appareilpeutêtreencastrésousunplandetravailcontinu*

(voir feuille de montage)

3.Installerlelave-vaissellesurunsolplatetrigide.Compenser

les irrégularités en vissant ou en dévissant les pieds avant

jusqu'àcequel'horizontalitédel’appareilsoitparfaite.Une

bonnehorizontalitégarantitlastabilitédel’appareiletsupprime

tout risque de vibrations, bruits et déplacements.

4*. Pour régler la hauteur du pied arrière, agir sur la douille rouge

à six pans située dans la partie avant du lave-vaisselle, en bas

etaumilieu,àl’aided’uneclémâleàsixpans,ouverture8mm.

Tourner dans le sens des aiguilles d’une montre pour augmenter

la hauteur et dans le sens inverse pour la diminuer.

(voir feuille

d’instructions jointe à la documentation)

Raccordements eau et électricité

L’adaptation des installations électriques et les travaux de

plomberiede l’installation doivent être effectués pardu

personnel qualifié.

Lelave-vaissellenedoitpasécraserlestuyauxoulecâble

d’alimentation électrique.

Utiliserdestuyauxneufspoureffectuerleraccordementde

l’appareil au réseau de distribution de l’eau.

Ne pas réutiliser les anciens tuyaux.

Lestuyauxd’amenéeet d’évacuationde l’eau et le câble

d’alimentationélectriquepeuventêtreorientésversladroiteou

vers la gauche pour simplifier l’installation.

Raccord du tuyau d’amenée de l’eau

• Auneprised'eaufroide:bienvisserletuyaud’amenéeà

unrobinet à emboutfileté3/4gaz ;avantdevisser, faire

couler l’eau jusqu’à ce quelle devienne limpide et dépourvue

d’impuretés qui pourraient engorger l’appareil.

• Auneprised'eauchaude:encasd’installationdechauffage

centralisé(radiateurs),le lave-vaisselle peut être alimenté

avecdel’eauchaudederéseaunedépassantpas60°C.

Visser le tuyau au robinet en procédant comme pour la prise

d'eaufroide.

Si la longueur du tuyau d’amenée ne suffit pas, s’adresser

à un magasin spécialisé ou à un technicien agréé

(voir

Assistance)

Lapressiondel’eaudoit êtrecompriseentrelesvaleurs

reportées dans le tableau des Caractéristiques techniques

(voir

ci-contre)

Attention à ce que le tuyau ne soit pas plié ou écrasé.

Raccordement du tuyau d’évacuation de l’eau

Raccorder le tuyau d’évacuation, sans le plier, à une conduite

d’évacuation ayant au moins 4 cm de diamètre.

Letuyaud’évacuationdoit être placé entre 40 et80cmau-

dessus du sol ou du plan d’appui du lave-vaisselle (A).

Avant de raccorder le tuyau d’évacuation de l’eau au siphon de

l’évier, retirer le bouchon en plastique (B).

Sécurité anti-fuite

Pour éviter tout risque d’inondation, le lave-vaisselle :

- est équipé d’un dispositif qui coupe l’arrivée de l’eau en cas

d’anomalie ou de fuite à l’intérieur de l’appareil.

Quelques modèles sont équipés d’un dispositif de sécurité

supplémentaire New Acqua Stop*, qui garantit contre tout

risqued'inondationmêmeencasderupturedutuyaud’amenée

de l’eau.

ATTENTION : TENSION DANGEREUSE !

Ilnefautenaucuncascouperletuyaud’amenéedel’eaucar

il contient des parties sous tension.

Raccordement électrique

Avantdebrancherlafichedanslaprisedecourant,s'assurer

que :

• laprise estbien reliéeàlaterre et est conforme aux

réglementations en vigueur ;

• lapriseestbienapteàsupporterlapuissancemaximalede

la machine reportée sur la plaquette signalétique fixée à la

contre-porte

(voir chapitre Description du lave-vaisselle) ;

• atensiond’alimentationestbiencompriseentrelesvaleurs

figurant sur la plaque signalétique de la contre-porte ;

• la prise est bien compatibleavec lafiche del’appareil.

Autrement, faire remplacer la fiche par un technicien agréé

(voir Assistance)

; n’utiliser ni rallonges ni prises multiples.

Aprèsinstallation de l’appareil, le câble d’alimentation

électriqueetla prise de courant doivent être facilement

accessibles.

Lecâblenedoitêtrenipliénitropécrasé.

Afin d’éviter tout danger, faire changer le cordon

d’alimentation abîmé, par le fabricant ou par son service après-

vente.

(Voir Assistance)

Installation

La page charge ...

Indesit DIFP 36 Le manuel du propriétaire

Marque: Indesit

Modèle: DIFP 36

Catégorie: Lave-vaisselle

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Indesit DIFP 36 Owner's manual

Indesit DIFP 36 Le manuel du propriétaire

Indesit DIFP 36 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents