Bauknecht TRWP 8711 Program Chart

Taper
Program Chart
1
MACHINE OPERATION
Additional information (including troubleshooting and service) can be found in the individual chapters of the
Instructions for use.
Sort laundry according to
care symbols
Do not tumble dry
Suitable for tumble drying
at low temperatures
Suitable for tumble drying
Sort laundry by:
Material thickness: whenever there is greater load than the dryer can handle, separate laundry
according to weight (e.g. dry towels and thin underwear separately).
Type of material: cotton (linen); synthetic textiles (easy care).
Degree of drying: cupboard dry, iron dry etc.
Do not tumble dry: nylon stockings, delicate embroidery, fabrics with metallic decorations.
Preparing laundry
Check that all fastenings are closed and that pockets are empty.
Please ensure that there are no cigarette lighters in the laundry.
Turn laundry inside out.
Loading dryer
Place laundry loosely in the drum to achieve equal drying throughout.
Then close the door.
Selecting programme
Select the drying programme required by turning the programme selector knob (for information,
refer to programme table).
If you do not start the programme soon after having made your choice, the dryer will switch off
after a few minutes.
To switch the dryer on again turn the programme selector knob to “Off” (“0”) and afterwards to
the desired programme.
Selecting options
(if available)
Select the option required by pressing the corresponding button.
The indicator lamp above the relevant button lights up to confirm your selection.
A fast blinking lamp indicates a wrong selection is made (incompatible options).
Press the button again to cancel the option.
Starting dryer
The drying programme is started by pressing the Start/Départ (Pause) (Start (Pause)) button.
The relevant indicator lamp lights up.
Changing programme selection: If the programme selected is changed during drying, the
dryer stops.
The Start/Départ (Pause) (Start (Pause)) indicator lamp flashes.
To operate the new programme, press the Start/Départ (Pause) (Start (Pause)) button again.
Interrupting programme: To interrupt a drying cycle, press the Start/Départ (Pause) (Start
(Pause)) button and open the door.
Wait at least 5 minutes, to allow the laundry to cool down, before you unload the dryer.
For your safety the drying cycle stops automatically if you open the door.
To restart, after door opening, close the door and press the Start/Départ (Pause) (Start
(Pause)) button again.
Warning: Never stop a tumble dryer before the end of the drying cycle, unless all items are
quickly removed and spread out so that the heat is dissipated.
Programme end
unloading dryer
The final part of a drying cycle occurs without heat (cool down cycle) to ensure that the items
reach a lower temperature to avoid wrinkling.
End: Take the laundry out of the dryer.
The drying process is complete.
Knitterschutz (Anticrease): If the laundry is not removed at the end of the drying cycle, an
automatic anti-crease cycle will operate for maximum 15 min (by choosing the option
Knitterschutz (Anticrease) this time can be extended up to 12 hours).
The drum rotates to prevent the laundry from creasing.
After the end of the Knitterschutz (Anticrease) the dryer will switch off after a short time, to
save energy.
Switching dryer off
Set the programme selector knob to Off” (“0”).
Cleaning the door filter after every cycle: open door, pull door filter up and out of machine and open it. Brush lint using a soft brush or
your fingertips. Close door filter and push firmly back into place.
Emptying water container: pull container out by the handle and empty. Replace the container when empty by pushing it completely
back into place.
Please note: Only use additives/plastic items specified as dryer safe and rinse items that have been treated with stain remover
thoroughly in plenty of water before drying. Never dry rubber objects or objects stained with vegetable oils in the dryer.
The Manufacturer is not liable for any damage to laundry resulting from inadequate or incorrect fabric care instructions which have been
provided with the garment or article.
Power consumption: in off-mode 0.011 W / in left on-mode 0.011 W
.
2
Overview of programmes Options
Approximate
drying times
(in minutes)
Fabrics
Gentle
Schonen
Délicat
Anticrease
Knitter-
schutz
Antifroissage
Dryness
adjustment
Trackengrad
Degré de
séchage
Buzzer
Summer
Sonnerie
Pause
Start
Départ
(Pause)
Drum light
Beleuchtung
Lumière
Finish in
Endzeit
Heure de fin
Very
wet load Wet load
Cotton
Extratrocken
Prêt à ranger
Cupboard dry +
Multi-layered, thick laundry such as:
terry towels, terry towelling bath robes.
Cotton or linen hot wash /
coloured laundry
Baumwolle
Coton
Max. 8.0 kg
X X X X X X X 200 130
Schranktrocken Plus
Prêt à porter Plus
Extra dry
Terry towels, dry towels, bed linen,
underwear
X X X X X X X 180 115
Schranktrocken
Prêt à porter
Cupboard dry*
Similar types of laundry which do not
require ironing such as: dry towels and
linen, underwear, baby clothes, T-shirts,
cotton socks.
X X X X X X X 165 100
Bügeltrocken
Prêt à repasser
Iron dry*
Laundry which requires ironing such as:
bed and table linen, dry towels, T-shirts,
polo shirts, work clothes.
X X X X X X X 145 85
Synthetic
Extratrocken
Prêt à ranger
Extra dry
Laundry with thick, multi-layered areas
such as: bed and table linen, track suits,
anoraks, blankets.
Synthetic, mixed fibre or cotton
easy care (ironing not required)
laundry
Pflgeleicht
Synthétiques
Max. 4.0 kg
X X X X X X X 85 70
Schranktrocken
Prêt à porter
Cupboard dry*
Laundry which does not require ironing
such as: shirts, blouses, T-shirts,
sportsware.
X X X X X X X 70 60
Bügeltrocken
Prêt à repasser
Iron dry
Laundry which requires ironing such as:
trousers, dresses, skirts, shirts, blouses.
X X X X X X X 60 50
Special
programmes
WollePro
Wool finish
Only for drying wool with specific label
from Woolmark : TOTAL EASY CARE
WOOL
Textiles made of wool
1.0 kg
X X X X X 60
Duvet
Down Sleeping bags, trousers, vests
Laundry that contains downs
3.0 kg
X X X X X 120 120
Airing
Laundry is aired, refreshed and loosen up for
30 minutes without heating.
All textiles.
Lüften/
Ventilation
X X X
Drying
times
Completes drying
(suitable for all fabrics)
Zeitprogramme
Minuterie
30’ 40’ 60’ 90’
X X X X X 30’ 40’ 60’ 90’
*Test programmes according to EN61121, tested with maximum rated load capacity.
3
HOW TO PROCEED IF
...you want to check the dryer yourself first:
(If your machine is not functioning correctly, please check the
following points before calling the customer service
also refer to relevant chapter in the Instructions for use)
Drying takes too long /
Laundry is not dry
enough
Has the correct drying programme been selected?
Has the cycle been interrupted (door opening, full water container)?
Was the inserted laundry too wet (washing machine spin speed less
than 1000 rpm)?
Is the door filter dirty (filter indicator light on)?
Is the bottom filter dirty (for more information, refer to the Instructions
for use)?
Is the room temperature too high?
Is the End and Knitterschutz (Anticrease) indicator lamp lighting
up? The drying cycle is complete and the laundry can be taken out.
If the drying result does not meet your expectation, select a more dry
programme or use the dryness adjustment option (if available) to
optimize the drying result.
The dryer does not
operate (after a power
failure, always press
the “Start/Départ
(Pause)” (Start
(Pause)) button)
Is the plug properly inserted into the mains electricity socket?
Is there a power failure?
Has the fuse blown?
Is the door properly closed?
Has a drying programme been selected?
Has the Start/part (Pause) (Start (Pause)) button been pressed
shortly after a programme is selected? (If not, the dryer will switch off.)
Has the start delay option been selected?
Is the dryer overloaded? à Please remove a part of the load.
Door filter, water
container or bottom
filter indicator lamp on
Is the door filter clean?
Is the water container empty?
Has the water container been inserted correctly?
Is the bottom filter clean and inserted correctly?
Water droplets
underneath the dryer
Has the bottom filter been inserted correctly?
Have all lint on the bottom filter seal and the door seal been wiped
away?
Has the water container been inserted correctly?
If the direct drain connection is used, is it tight?
Is the dryer leveled?
...you want to
care of and clean your dryer:
Clean the door filter at
the end of every cycle
Brush lint using a soft brush or your fingertips.
Close the filter.
Push the filter back into place.
Empty the water
container at the end of
every drying cycle
Pull the handle to remove the water container.
Empty the water container.
Replace the water container when empty by pushing it completely back
into place.
Clean the bottom filter
every fifth cycle
Clean the bottom filter under running water.
Remove all fluffs from the seals.
Clean the bottom filter housing (for further information see chapter
Cleaning the Bottom Filterin the Instructions for use).
See the Instruction for use for further information on how to clean the
bottom filter.
4
FAILURE CODES
In case of a malfunction of the dryer,
one the following failure codes could be displayed.
Depending on the model of your dryer, the failure can be displayed in letters or by different blinking lamps.
Failure
code
Lamps failure code
Check needed by customer before
Service call
F01
Please call the After-Sales-Service.
F02
Please call the After-Sales-Service.
F03
Please call the After-Sales-Service.
F04
Please call the After-Sales-Service.
F05
Turn OFF the dryer.
Unplug the dryer.
Assure that the ambient temperature is
between 5°C and 35°C.
Wait for 1 hour.
Plug the dryer again and restart the dryer.
If the failure occurs again, please call the
After-Sales-Service.
F06
F07
F10 F22
Turn OFF the dryer.
Unplug the dryer.
Wait for 30 minutes.
Plug the dryer again and restart the dryer.
If the failure occurs again, please call the
After-Sales-Service.
Start lamp is blinking 2 times per second when it is pressed
Assure that the door is correctly closed and
heat exchanger correctly positioned.
Bottom filter lamp is blinking or Door filter lamp is blinking
2 times per second when the Start button is pressed
Assure that the bottom filter is correctly
positioned.
5
Before using the machine, please also read the instructions for use carefully!
Quick Reference Guide
Indicator lamps and Options
Programme selector knob
The drying programme is
selected by turning
this knob.
The “Start (Pause)” indicator lamp flashes.
“Start (Pause)” button
The drying programme is s
tarted by pressing
this button.
The indicator lamp lights up.
Door filter
The indicator lamp lights up when the
door
filter needs to be cleaned.
Clean the
door filter at the end of every
drying cycle.
Bottom filter
Th
is indicator lamp lights up when the
bottom
filter needs to be cleaned.
This indicator lamp is blinking, when the
bottom filter is not correctly positioned.
Please take care that the bottom filter is
inserted and the handle is fully equipped.
Water container
The indicator lamp lights up when the water
container needs to be emptied.
The drying cycle is automatically interrupted.
Empty the container and restart the drying
programme.
Empty the water container after every
drying cycle
“Remaining time” display
Depending on the programme selected a
de
fault drying time is displayed.
After start of cycle the time displayed is
corrected depending on the volume, type and
moisture of the laundry.
The drying time specified is a calculated
value which will
be updated during the
drying cycle.
The flashing lines indicate that the calculation
is running.
The remaining time will be updated.
Eco Monitor
The
“Eco monitor” gives you a rough
feedback about the energy consumption of
the
selected programme.
This
function will not work for a time based
programme.
As soon as you turn the programme selector
to any humidity steared programme, the
“Eco monitor
lamps will indicate the
expected energy consumption.
The three indicators show the degree of
consumption:
the less energy your
programme setting is forecasted to consume,
the less indicators will light up.
This depends on the programme, init
ial
moisture and options selected, and also on
the size of the load.
For that reason, the forecasted degree of
energy co
nsumption may adapt when the
tumble dryer detects the load size.
End
Th
e drying programme is finished.
Please unload the dryer.
6
Overdry protection
The indicator lights up when a humidity
controlled programme is selected, to indicate
the activated protection function.
Dryness level
By selecting this option you can adjust the
dryness level of the laundry. After the
selection
of the desired programme you can
choose the
dryness level by pressing the
button.
Pressing 1 time you select a more dry
level
or
Pressing 2 times you select a less dry level
or
Pressing 3 times you select again normal dry
level.
Buzzer
Pressing this option, an acoustic signal is
indicating the end of the drying cycle.
This option deactivates the
“Anticrease”
function, if it is activated.
Gentle
Selecting this option will
reduce the drying
temperature.
This option cannot be selected when the
option “Rapid” is selected.
Anticrease
This option can be chosen to reduce
wrinkling, when the laundry is not
unloaded
d
irectly after end of the cycle.
The drum turns from time to time for
maximum 12
hours.
It can be interrupted at any t
ime by switching
off the dryer.
This option deactivates the
Buzzer
function, if it is activated.
Drum light
Th
e drum light can be switched on and off.
Finish in
With this function you can postpone your
programme to complete at a later time: press
the button to select in how many hours the
programme shall be finished.
Thus, it allows you to have your laundry
ready at a particular time and to profit
from more favorable energy rates during
the night, for example.
The Finish in” function can be selected
in full hour time segments (1 to 24 h).
When you press the button, the shortest
possible time will be displayed; keep on
pressing the button to loop through all the
available times.
To remove it again, keep on pressing the
button until you see the value off” “0”
position.
When you have selected the desired
Finish in” time, press “Start”the
countdown will begin.
During the countdown, you can still
modify the option setting (select or
deselect options).
Sometimes the programme may finish
before the selected “Finish in time has
expired (e.g. for small loads).
In this case, the dryer will tumble the
laundry regularly to keep it fresh, until the
selected Finish in” time has expired.
During tumbling, the display will show an
animation.
The tumbling phase can be stopped at
any time either by pressing any button, b
y
rotating the programme selector or by
opening the door.
5019 400 00320
(Subject to technical modifications)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Bauknecht TRWP 8711 Program Chart

Taper
Program Chart

dans d''autres langues