Briggs and Stratton SP1697092 Manuel utilisateur

Not for

Reproduction

48V

LITHIUM-ION BATTERY CHARGER

Read all safety rules and instructions carefully before operating this tool.

Owner’s Manual

TOLL-FREE HELPLINE: 1-800-743-4115

www.briggsandstratton.com

48V Lithium-ion Battery Charger

1697092 & 80075686 (BS2AC48)

Not for

Reproduction

2

CONTENTS

Product Specications ............................................................................. 2

Important Safety Instructions ................................................................. 3

Symbols .................................................................................................. 6

Know Your Charger ................................................................................. 7

Operation ................................................................................................ 8

Maintenance ..........................................................................................11

Troubleshooting................................................ .........................................12

Limited Warranty................................................................................ 13

PRODUCT SPECIFICATIONS

COMPONENTS SPECIFICATIONS

Charger 48V Lithium-ion Battery Charger

Model BS2AC48

Input 120V AC, 50/60Hz, 1.8A

Output 48V DC, 2A

Weight 1.79 lbs (0.81 kg)

Disclaimer: *Maximum initial battery voltage (measured without a

workload) is 48 volts. Nominal voltage is 43.

Not for

Reproduction

3

IMPORTANT SAFETY INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS – SAVE

THESE INSTRUCTIONS

DANGER – TO REDUCE THE RISK OF FIRE OR

ELECTRIC SHOCK, CAREFULLY FOLLOW THESE

INSTRUCTIONS

Read and understand all instructions before using this product. Failure to

follow all instructions listed below may result in electric shock, fire, and/or

serious personal injury.

WARNING

FOR INDOOR USE ONLY.

CAUTION

Risk of Electric Shock.

Dry location use only.

CAUTION

RISK OF FIRE OR ELECTRIC SHOCK, DO NOT INTERCONNECT

OUTPUT TERMINATIONS.

CAUTION

CHARGE ONLY RECHARGEABLE BATTERY PACK BSB2AH48,

BSB5AH48, OTHER TYPES OF BATTERIES MAY BURST CAUSING

PERSONAL INJURY AND DAMAGE.

DANGER

RISK OF ELECTRIC SHOCK. DO NOT TOUCH UNINSULATED PORTION

OF OUTPUT CONNECTOR OR UNINSULATED BATTERY TERMINAL.

• SAVE THESE INSTRUCTIONS - This manual contains important safety

and operating instructions for battery charger BS2AC48.

• Before using battery charger, read all instructions and cautionary markings

on battery charger, battery, and product using battery.

Not for

Reproduction

4

IMPORTANT SAFETY INSTRUCTIONS

• To reduce the risk of re and electric shock, install in a temperature- and

humidity-controlled indoor area relatively free of conductive contaminants.

• Use of an attachment not recommended or sold by the battery charger

manufacturer may result in a risk of re, electric shock, or injury to persons.

Following this rule will reduce the risk of electric shock, fire, or serious

personal injury.

• Do not abuse cord or charger. Never use the cord to carry the charger.

Do not pull the charger cord rather than the plug when disconnecting from

receptacle. Damage to the cord or charger could occur and create an

electric shock hazard. Replace damaged cords immediately.

• Do not operate charger if it has received a sharp blow, been dropped, or

otherwise damaged in any way. Take it to an authorized serviceman for

electrical check to determine if the charger is in good working order.

• Do not cover the ventilation slots on the top of the charger. Do not set the

charger on a soft surface i.e. blanket, pillow. Keep the ventilation slots of the

charger clear.

• Do not probe the charger with conductive materials.

• Do not disassemble charger. Take it to an authorized serviceman when

service or repair is required. Incorrect reassembly may result in a risk of

electric shock or re.

• Disconnect charger from the power supply when not in use. This will reduce

the risk of electric shock or damage to the charger if metal items should fall

into the opening. It also will help prevent damage to the charger during a

power surge.

• Do not mix old and new batteries and do not mix alkaline, standard

(carbonzinc) or rechargeable (ni-cad, ni-mh, etc.) batteries.

• Do not use a damp cloth or detergent on the battery or battery charger.

• Do not allow the battery pack or charger to overheat. If they are warm, allow

them to cool down. Recharge only at room temperature.

• Unplug the charger before cleaning and when there is no battery pack in the

cavity.

• Do not try to connect two chargers together.

• Do not allow liquid inside the charger.

Not for

Reproduction

5

• Do not try to use the charger for any other purpose than what is presented

in this manual.

• Store indoors, and do not expose to rain or water, avoid direct sunshine.

• Be sure voltage selector is in correct voltage position before plugging in.

• For use in the U.S.A., the voltage selector switch must be placed in the 120

volt position. For use in countries other than the U.S.A., the voltage selector

may need to be placed in other than the 120 volt position. Confirm the

voltage available at each country location before using the product.

• This power unit is intended to be correctly orientated in a vertical or oor

mount position.

• Save these instructions. Refer to them frequently and use them to instruct

others who may use this tool. If you loan someone this tool, loan them these

instructions also to prevent misuse of the product and possible injury.

IMPORTANT SAFETY INSTRUCTIONS

Not for

Reproduction

6

SYMBOLS

Some of the following symbols may be used on this product. Please study them

and learn their meaning. Proper interpretation of these symbols will allow you to

operate the product better and safer.

SYMBOL NAME DESIGNATION/EXPLANATION

V Volts Voltage

Hz Hertz Frequency (cycles per second)

W Watts Power

Direct Current Type or a characteristic of current

Wet Conditions Alert

Do not expose to rain or use in damp

locations.

Read The Operator’s

Manual

To reduce the risk of injury, user

must read and understand operator’s

manual before using this product.

Safety Alert Precautions that involve your safety.

The following signal words and meanings are intended to explain the levels of

risk associated with this product.

DANGER

Indicates an imminently hazardous situation, which,

if not avoided, will result in death or serious injury.

WARNING Indicates a potentially hazardous situation, which, if

not avoided,could result in death or serious injury.

CAUTION Indicates a potentially hazardous situation, which, if

not avoided,may result in minor or moderate injury.

CAUTION (Without Safety Alert Symbol) Indicates a situation

that may result in property damage.

SYMBOL SIGNAL MEANING

Not for

Reproduction

7

KNOW YOUR CHARGER

The safe use of this product requires an understanding of the information

on the product and in this operator’s manual as well as a knowledge of the

project you are attempting. Before using this product, familiarize yourself with

all operating features and safety rules.

Electrical Contacts

Cooling Air Port

LED Light

Wall Mounting Holes

Power Cord

Not for

Reproduction

This device complies with Part 15 of the FCC Rules. Operation is subject to

the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference

that may cause undesired operation.

WARNING

Changes or modifications to this unit not expressly approved by the party

responsible for compliance could void the user’s authority to operate the

equipment.

NOTE: This equipment has been tested and found to comply with the limits

for Class B digital device, pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following

measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and the receiver.

- Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

WARNING

Do not allow familiarity with products to make you careless. Remember that a

careless fraction of a second is sufcient to inict serious injury.

WARNING

Do not use any attachments or accessories not recommended by the

manufacturer of this product. The use of attachments or accessories not

recommended can result in serious personal injury.

OPERATION

8

Not for

Reproduction

9

OPERATION

CAUTION

Charge in a well ventilated area. Do not block charger vents. Keep them clear

to allow proper ventilation.

CHARGING PROCEDURE

NOTE: The battery is not shipped fully charged. It is recommended to fully

charge before rst use to ensure that maximum run time can be achieved.

This lithium-ion battery will not develop a memory and may be charged at any

time.

Low voltage charging:

If the battery has been stored with little to no charge for a long period of time,

the charger will go into recovery mode, which will take 20 hrs to fully charge

the battery. This will enhance the life of the battery. Once it is fully charged,

the next charge will return to standard charging.

1. Plug the charger into an AC power outlet.

2. Insert the battery pack into the charger.

This is a diagnostic charger. The Charger LED Lights will illuminate in specic

order to communicate the current battery status. They are as follows:

LED STATUS DESCRIPTION

Solid Green Fully Charged

Blinking Green Charging

Solid Red Over Temperature

Blinking Red

Charging Fault

Charging Over

Temperature

Charging

Fault

Fully

Charged

Not for

Reproduction

10

OPERATION

False defect note:

When the battery is inserted into the charger and the status LED blinks RED,

remove the battery from the charger for 1 minute, then reinsert. If the status

LED blinks GREEN, then the battery is properly charging. If the status LED

is still blinking RED, remove the battery and unplug the charger for 1 minute.

After 1 minute, plug in the charger and reinsert the battery. If the status LED

blinks GREEN, then the battery is properly charging. If the status LED is still

blinking RED, the battery is defective and needs to be replaced.

CHARGER MOUNTING

1. This charger can be installed hanging on a wall using two #8 screws (not

included).

2. Locate the placement for the charger to be wall mounted.

3. If fastening to wood studs use 2 wood screws (not included).

4. For Charger BS2AC48: Drill two holes on center 3.63 in. apart ensuring that

they are vertically aligned.

5. If fastening to drywall use wall anchors (not included) and screws to secure

the charger to the wall.

6. This power unit is intended to be correctly orientated in a vertical or floor

mount position.

NOTE: If the battery and the charger won’t be used for a long time, remove the

battery from the charger and pull out the AC power plug.

Not for

Reproduction

11

MAINTENANCE

WARNING

To avoid serious personal injury, always remove the battery pack from the tool

when cleaning or performing any maintenance.

WARNING

When servicing, use only identical Briggs & Stratton replacement parts. Use of

any other parts may create a hazard or cause product damage.

WARNING

It is not recommended to use compressed dry air as cleaning method of the

charger. If cleaning with compressed air is the only method to apply, always

wear safety goggles or safety glasses with side shields when using compressed

air to clean the tool. If the operation is dusty, also wear a dust mask.

GENERAL MAINTENANCE

• Brush or blow dust and debris out of the air vents using compressed air or a

vacuum. Keep the air vents free of obstructions, sawdust, and wood chips.

Do not spray, wash, or immerse the air vents in water.

• Wipe off the housing and the plastic components using a dry, soft cloth.

Do not use strong solvents or detergents on the plastic housing or plastic

components. Certain household cleaners may cause damage and may

cause a shock hazard.

STORAGE

• Always remove the battery pack before storing the charger or any time the

charger is unplugged.

• Do not place the battery pack in the sun or in a warm environment. Keep at

normal room temperature.

• If the battery will not be used for 3 months or more, please store the battery

in a room temperature environment. Please fully charge before storage.

WARNING

Do not at any time let brake fluids, gasoline, petroleum-based products,

penetrating oils, etc. to come in contact with plastic parts. Chemicals can

damage, weaken or destroy plastic which may result in serious personal injury.

Not for

Reproduction

TROUBLESHOOTING

12

PROBLEM CAUSE SOLUTION

Charger doesn't work.

Charger shows defective

mode (LED ashes Red).

Battery pack or charger

is defective or bad

connection between

the battery pack and

charger.

1. Try to remove and

reinsert the battery pack

in the charger.

2. Try charging a

different battery pack.

3. Unplug the charger

and wait until the red

LED goes out, then

reconnect the plug to the

power supply.

Charger doesn't

work. Charger shows

evaluative mode (LED

indicates Red solid ON).

Battery pack is too hot or

too cold.

Allow the battery

pack to reach normal

temperature. Charging

will begin when battery

pack returns to 3°C-47°C

(37°F-117°F).

Not for

Reproduction

LIMITED WARRANTY

13

Briggs & Stratton warrants that, during the warranty period specied below,

it will repair or replace, free of charge, any part that is defective in material

or workmanship or both. Transportation charges on product submitted for

repair or replacement under this warranty must be borne by purchaser. This

warranty is effective for and is subject to the time periods and conditions

stated below. For warranty service, nd the nearest Authorized Service Dealer

in our dealer locator map at www.briggsandstratton.com. The purchaser must

contact the Authorized Service Dealer, and then make the product available

to the Authorized Service Dealer for inspection and testing.

There is no other express warranty. Implied warranties, including those

of merchantability and tness for a particular purpose, are limited to the

warranty period listed below, or to the extent permitted by law. Liability

for incidental or consequential damages are excluded to the extent exclusion

is permitted by law. Some states or countries do not allow limitations on how

long an implied warranty lasts, and some states or countries do not allow

the exclusion or limitation of incidental or consequential damages, so the

above limitation and exclusion may not apply to you. This warranty gives you

specic legal rights and you may also have other rights which vary from state

to state or country to country.**

WARRANTY PERIOD

Consumer Use Commercial Use

Equipment 36 months None

Battery and Battery Charger 24 months None

** In Australia - Our goods come with guarantees that cannot be excluded

under the Australian Consumer Law. You are entitled to a replacement or

refund for a major failure and for compensation for any other reasonably

foreseeable loss or damage. You are also entitled to have the goods repaired

or replaced if the goods fail to be of acceptable quality and the failure does not

amount to a major failure. For warranty service, nd the nearest Authorized

Service Dealer in our dealer locator map at BRIGGSandSTRATTON.COM,

or by calling 1300 274 447, or by emailing or writing to salesenquires@

briggsandstratton.com.au, Briggs & Stratton Australia Pty Ltd, 1 Moorebank

Avenue, NSW, Australia, 2170.

Not for

Reproduction

LIMITED WARRANTY

14

The warranty period begins on the date of purchase by the first retail

or commercial consumer. “Consumer use” means personal residential

household use by a retail consumer. “Commercial use” means all other uses,

including use for commercial, income producing or rental purposes. Once a

product has experienced commercial use, it shall thereafter be considered as

a commercial use product for purposes of this warranty.

To ensure prompt and complete warranty coverage, register your product at

the website shown above or at www.onlineproductregistration.com.

Save your proof of purchase receipt. If you do not provide proof of the initial

purchase date at the time warranty service is requested, the manufacturing

date of the product will be used to determine the warranty period. Product

registration is not required to obtain warranty service on Briggs & Stratton

products.

ABOUT YOUR WARRANTY

Warranty service is available only through Briggs & Stratton Authorized

Service Dealers. This warranty covers only defects in materials or

workmanship. It does not cover damage caused by improper use or abuse,

improper maintenance or repair, normal wear and tear, or stale or unapproved

fuel.

Improper Use and Abuse - The proper, intended use of this product is

described in the Operator’s Manual. Using the product in a way not described

in the Operator’s Manual or using the product after it has been damaged

will not be covered under this warranty. Warranty coverage will also not be

provided if the serial number on the product has been removed or the product

has been altered or modified in any way, or if the product has evidence of

abuse such as impact damage or water/chemical corrosion damage.

Improper Maintenance or Repair - This product must be maintained

according to the procedures and schedules provided in the Operator’s

Manual, and serviced or repaired using genuine Briggs & Stratton parts or

equivalent. Damage caused by lack of maintenance or use of non-original

parts is not covered by warranty.

Not for

Reproduction

LIMITED WARRANTY

Normal Wear and Tear - Like most mechanical devices, your unit is subject

to wear even when properly maintained. This warranty does not cover

repairs when normal use has exhausted the life of a part or the equipment.

Maintenance and wear items such as filters, belts, cutting blades, and

brake pads (except engine brake pads) are not covered by warranty due to

wear characteristics alone, unless the cause is due to defects in material or

workmanship.

Other Exclusions - This warranty excludes damage due to accident,

abuse, modifications, alterations, improper servicing, freezing or chemical

deterioration. Attachments or accessories that were not originally packaged

with the product are also excluded. There is no warranty coverage on

equipment used for primary power in place of utility power or on equipment

used in life support applications. This warranty does not include used,

reconditioned, second-hand, or demonstration equipment or engines. This

warranty also excludes failures due to acts of God and other force majeure

events beyond the manufacturer’s control.

15

Not for

Reproduction

TOLL-FREE HELPLINE: 1-800-743-4115

80077956 Rev: 04 (11-21-18)

Not for

Reproduction

Avant d’utiliser le produit, veuillez lire et suivre toutes les consignes de

sécurité et les instructions d’utilisation.

Guide D’utilisation

LIGNE D’ASSISTANCE SANS FRAIS : 1-800-743-4115

www.briggsandstratton.com

Chargeur de batterie lithium-ion 48V

1697092 & 80075686 (BS2AC48)

CHARGEUR DE BATTERIE LITHIUM-ION 48V

Not for

Reproduction

2

MATIÈRES

Fiche Technique

............................................................................................................

2

Consignes De Sécurité Importantes

......................................................................

3

Symboles

.........................................................................................................................

5

Veiller À Bien Connaître Votre Chargeur

...............................................................

6

Utilisation

.........................................................................................................................

7

Entretien

........................................................................................................................

10

Dépannage

................................................ ......................................................................

11

Garantie Limitée

.......................................................................................................

12

FICHE TECHNIQUE

COMPOSANT CARACTÉRISTIQUES

Chargeur Chargeur De Batterie Lithium-ion

48V

Modèle BS2AC48

Entrée 120V AC, 50/60Hz, 1.8A

Sortie 48V DC, 2A

Piods 1.79 lbs (0.81 kg)

Avis de non-responsabilité : *La tension initiale et maximale de la

batterie (mesurée à vide) est de 48 volts. La tension nominale est de 43 V.

Not for

Reproduction

3

CONSIGNES DE SÉCURITÉ IMPORTANTES

CONSIGNES DE SÉCURITÉ IMPORTANTES –

CONSERVEZ CES INSTRUCTIONS

DANGER – POUR RÉDUIRE LES RISQUES

D’INCENDIE OU DE DÉCHARGE ÉLECTRIQUE,

SUIVEZ SCRUPULEUSEMENT CES INSTRUCTIONS

Lire et veiller à bien comprendre toutes les instructions. Le non-respect

de toutes les instructions ci-dessous peut entraîner un choc électrique, un

incendie et/ou des blessures graves.

AVERTISSEMENT

POUR UNE UTILISATION À L’INTÉRIEUR EXCLUSIVEMENT.

ATTENTION

Risque de choc électrique.

Utilisez l’unité uniquement dans un endroit sec.

ATTENTION

RISQUE D’INCENDIE ET D’ÉLECTROCUTION, NE CROISEZ PAS LES

BORNES DE SORTIE.

ATTENTION

CHARGEZ UNIQUEMENT LA BATTERIE RECHARGEABLE BSB2AH48,

BSB5AH48, LES AUTRES TYPES DE BATTERIES POURRAIENT

EXPLOSER, MAIS AUSSI CAUSER BLESSURES ET DOMMAGES.

DANGER

RISQUE DE CHOC ÉLECTRIQUE. NE PAS TOUCHER LES PARTIES NON

ISOLÉES DU CONNECTEUR DE SORTIE OU LES BORNES DE PILES

NON ISOLÉES.

• CONSERVEZ CES INSTRUCTIONS - Ce manuel contient d’importantes

instructions relatives à la sécurité et au fonctionnement des chargeur de

piles BS2AC48.

• Avant d’utiliser le chargeur de piles, lire toutes les instructions et les mises

en garde gurant sur le chargeur de pile, sur la pile et sur le produit utilisant

la pile.

• An de réduire les risques d’incendie et d’électrocution, installez l’outil dans

une pièce dont la température et l’humidité sont contrôlées, et ne présentant

aucun contaminant conducteur ou libre.

Not for

Reproduction

4

CONSIGNES DE SÉCURITÉ IMPORTANTES

• L’usage d’un accessoire non recommandé ou vendu par le fabricant du

chargeur peut causer un risque d’incendie, de choc électrique ou de

blessures. Le respect de cette consigne réduira les risques d’incendie, de

choc électrique et de blessures graves.

• Ne pas maltraiter le cordon d’alimentation ou le chargeur. Ne jamais utiliser

le cordon d’alimentation pour transporter le chargeur. Ne pas débrancher

le chargeur en tirant sur le cordon. Tirer sur la fiche pour la débrancher.

Un cordon ou un chargeur endommagé peut présenter un risque de choc

électrique. Remplacer immédiatement tout cordon endommagé.

• Ne pas utiliser le chargeur s’il a été soumis à un choc violent ou autrement

endommagé. Le coner à un réparateur agréé an qu’il détermine s’il est en

bon état de fonctionnement.

• Ne couvrez pas les fentes de ventilations situées sur le dessus du chargeur.

Ne posez pas le chargeur sur une surface souple, telle qu’une couverture

ou un oreiller. Gardez les fentes de ventilation du chargeur dégagées.

• N’introduisez pas de matériaux conducteurs dans le chargeur.

• Ne pas démonter le chargeur. Si un entretien ou une réparation est

nécessaire, le coner à un réparateur agréé. Un remontage incorrect peut

entraîner des risques de choc électrique ou d’incendie.

• Lorsqu’il n’est pas en usage, débrancher le chargeur de l’alimentation

secteur. Ceci réduira le risque de choc électrique ou de dommages au

chargeur si des articles en métal venaient à tomber dans l’ouverture. Ceci

aidera également à éviter des dommages au chargeur en cas de saute de

tension.

• Ne mélangez pas des piles neuves et usagées, ne mélangez pas des piles

alcalines, standards (carbone-zinc) et rechargeables (ni-cad, ni-mh, etc.).

• Ne pas utiliser de tissu humide ni de détergent sur la pile ni sur le chargeur

de la pile.

• Ne laissez pas la batterie ou le chargeu r surchauffer. S’ils sont chauds,

laissez-les refroidir. Ne procédez à la charge qu’à température ambiante.

• Débranchez le chargeur avant de le nettoyer et lorsqu’aucune batterie n’y

est connectée.

• Ne tentez de relier deux chargeurs ensemble.

• Ne laissez aucun liquide pénétrer dans le chargeur.

• Ne tentez pas d’utiliser le chargeur dans tout autre but que celui décrit dans

ce manuel.

• Entreposer à l’intérieur et protéger de la pluie ou de l’eau, éviter une

exposition directe à la lumière du soleil.

• Conserver ces instructions. Les consulter fréquemment et les utiliser

pour instruire les autres utilisateurs éventuels. Si cet outil est prêté, il doit

être accompagné de ces instructions, afin d’éviter un usage incorrect et

d’éventuelles blessures.

La page charge ...

Briggs and Stratton SP1697092 Manuel utilisateur

Briggs and Stratton SP1697092 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents