Crestron ZUMMESH-NETBRIDGE Quick Start

Taper
Quick Start

Ce manuel convient également à

The Crestron® ZUMMESH-NETBRIDGE adds enhanced integration
and setup capabilities to a Zūm space. It provides Zūm Net wireless
communication with a ZUM-FLOOR-HUB (not included) to enable
every space in the building to be centrally monitored, managed, and
controlled as part of a complete Zūm commercial lighting solution.
The ZUMMESH-NETBRIDGE also provides Bluetooth® connectivity to
allow room setup using a mobile device running the Zūm app.
NOTE: Only one ZUMMESH-NETBRIDGE can be installed per Zūm
space.
Check the Box
Item Qty
ZUMMESH-NETBRIDGE 1
The Zūm App
The Zūm app is available for download from the App Store® app
in iTunes® software or from the Google Play™ store. The Zūm app
provides setup of a Zūm space using a mobile device.
Installation
The ZUMMESH-NETBRIDGE snaps onto the expansion port of a
ZUMMESH-JBOX device (not included).
NOTES: Observe the following points.
Install and use this product in accordance with appropriate
electrical codes and regulations.
This meets the requirements of UL® standard 2043 for
installation in an environmental air-handling (plenum) space.
Ensure that the ZUMMESH-NETBRIDGE is installed within
range of the ZUMNET-GATEWAY.
Install the ZUMMESH-NETBRIDGE
1. Insert a flat-head screwdriver into the slot next to the cover and
pry up to remove the cover from the ZUMMESH-JBOX.
2. Align the ports on the ZUMMESH-NETBRIDGE and the
ZUMMESH-JBOX device, and then insert the network bridge
into the ZUMMESH-JBOX device. The network bridge snaps into
place.
Neutral (white)
Hot (black)
100-277 VAC power
from breaker
Remove the ZUMMESH-NETBRIDGE
1. Place your thumb on the side of the ZUMMESH-NETBRIDGE
that is nearest the J-box.
2. Press the ZUMMESH-NETBRIDGE away from the J-box. While
pressing on the side of the ZUMMESH-NETBRIDGE, slightly
lift your thumb up. The ZUMMESH-NETBRIDGE should easily
detach from the J-box device.
Join a Zūm Net Network
The ZUMMESH-NETBRIDGE communicates with a
ZUMNET-GATEWAY using Zūm Net wireless communications.
Join a Zūm Net Network:
1. Press the ACQUIRE button on the ZUMNET-GATEWAY to place
the gateway into Acquire mode.
2. Press the SET button on the ZUMMESH-NETBRIDGE four
times. DO NOT release the button after the fourth press. Hold
the SET button until the LED flashes once (up to 10 seconds)
and then release the button. The SET LED slowly flashes to
indicate that it is searching for a network to join.
The SET LED lights for 5 seconds when the network bridge
successfully joins the gateway.
The SET LED flashes quickly to indicate that the network
bridge failed to join the gateway. Press the SET button to
acknowledge the failure and then repeat this procedure.
3. Press the ACQUIRE button on the ZUMNET-GATEWAY to exit
Acquire mode.
Leave a Zūm Net Network:
1. Verify that the ZUMMESH-NETBRIDGE is not within range of a
ZUMNET-GATEWAY that is in Acquire mode.
2. Press the SET button on the ZUMMESH-NETBRIDGE four
times. DO NOT release the button after the fourth press. Hold
the SET button until the LED flashes once (up to 10 seconds)
and then release the button. The LED flashes slowly.
3. The SET LED then flashes quickly to indicate that the device has
left the Zūm Net wireless network.
4. Press the SET button to confirm that the device has left the
ZUMNET-GATEWAY’s wireless network
ZUMMESH-NETBRIDGE
Zūm™ Wireless Network Bridge
Verifying Communications Status
To check the communications status of the device, press the SET
button on the ZUMMESH-NETBRIDGE four times. DO NOT release
the button after the fourth press. Hold the SET button for less than
2 seconds and then release the button. The red SET LED indicates the
communications status. Refer to the following table for details.
LED Communications Status
Red LED turns on
for 5 seconds
The device is communicating with the
ZUMNET-GATEWAY and ZUM-FLOOR-HUB.
Red LED flashes
three times
The device is communicating with the
ZUMNET-GATEWAY, but the gateway is not
communicating with the ZUM-FLOOR-HUB.
Red LED flashes
twice
The device was previously joined to the
network but is not communicating with the
ZUMNET-GATEWAY.
Red LED flashes
once
The device is not joined to the
ZUMNET-GATEWAY.
LED Indicator
The SET LED indicates the current status of the
ZUMMESH-NETBRIDGE.
LED Status
Green - Solid The ZUMMESH-NETBRIDGE is acquired to the
gateway and RF communications are stable.
Red - Solid The ZUMMESH-NETBRIDGE is not acquired to
a gateway.
Red/Green -
Flashing
The ZUMMESH-NETBRIDGE was acquired to
the gateway but RF communications have been
lost.
Additional Information
Scan or click the QR code for detailed product information.
ZUMMESH-NETBRIDGE
Compliance and Legal
Original Instructions: The U.S. English version of this document is the original instructions.
All other languages are a translation of the original instructions.
As of the date of manufacture, the product has been tested and found to comply with
specifications for CE marking.
This product is Listed to applicable UL® Standards and requirements tested by Underwriters
Laboratories Inc.
Ce produit est homologué selon les normes et les exigences UL applicables par Underwriters
Laboratories Inc.
Federal Communications Commission (FCC) Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) This device must
accept any interference received, including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the manufacturer
responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna
Increase separation between the equipment and the receiver
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected
Consult the dealer or an experienced radio/TV technician for help
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator and your body. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
Industry Canada (IC) Compliance Statement
CAN ICES-3(B)/NMB-3(B)
This equipment complies with IC RSS‐102 radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with minimum
distance 20cm between the radiator and your body.
Cet équipement est conforme aux limites d’exposition aux radiations IC CNR‐102 établies
pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec une
distance minimale de 20 cm entre le radiateur et votre corps.
L’émetteur/récepteur exempt de licence contenu dans le psent appareil est conforme aux
CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :
L’appareil ne doit pas produire de brouillage;
L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
The product warranty can be found at www.crestron.com/warranty.
The specific patents that cover Crestron products are listed at
www.crestron.com/legal/patents.
Certain Crestron products contain open source software. For specific information, please
visit www.crestron.com/opensource.
Crestron, the Crestron logo, and Zūm are either trademarks or registered trademarks of
Crestron Electronics, Inc. in the United States and/or other countries. App Store and iTunes
are either trademarks or registered trademarks of Apple Inc. in the United States and/
or other countries. Bluetooth is either a trademark or registered trademark of Bluetooth
SIG, Inc. in the United States and/or other countries. Google Play is either a trademark or
registered trademark of Google Inc. in the United States and/or other countries. UL and the
UL logo are either trademarks or registered trademarks of Underwriters Laboratories, Inc.
in the United States and/or other countries. Other trademarks, registered trademarks, and
trade names may be used in this document to refer to either the entities claiming the marks
and names or their products. Crestron disclaims any proprietary interest in the marks and
names of others. Crestron is not responsible for errors in typography or photography.
©2019 Crestron Electronics, Inc.
Crestron Electronics, Inc.
15 Volvo Drive, Rockleigh, NJ 07647
Tel: 888.CRESTRON
Fax: 201.767.7576
www.crestron.com
Quick Start - Doc. 7955C
(2053726)
04.19
Specifications subject to
change without notice.
  • Page 1 1
  • Page 2 2

Crestron ZUMMESH-NETBRIDGE Quick Start

Taper
Quick Start
Ce manuel convient également à

dans d''autres langues