Crestron HZ-DIMEX Quick Start

Marque: Crestron

Modèle: HZ-DIMEX

Catégorie: Gradateurs

Taper: Quick Start

The HZ-DIMEX features the following:

• infiNET EX® Wireless Communication to Crestron® Gateway

(CEN-GWEXER)

• Field replaceable, engravable button caps available in various sizes

(not supplied)

• Forward-phase dimming

• REM input for multiway control for up to four HZ-KPEX or HZ-AUX

devices

The HZ-DIMEX is compatible with incandescent, magnetic low voltage, and

tungsten-halogen loads and offers the following load ratings:

• Input Rating: 120 VAC (Requires Neutral Wire Connection)

• Output Rating: 750 W/VA Max. (No Minimum Load)

Check the Box

Item Qty

HZ-DIMEX* 1

Screw, 6-32 x 3/4 in., Truss Head, Combo (P/N 2009211) 2

Spacer, Multi-Gang Alignment (P/N 2049924) 1

Nut, Wire, Blue (P/N 2045230) 1

* Refer to the HZ-DIMEX product page at www.crestron.com for a complete

list of color and texture variations.

Important Notes

WARNINGS:

• To avoid fire, shock, or death, turn off power at circuit breaker or fuse

and test that power is off before wiring!

• New installations should be checked for short circuits prior to installing

an HZ-DIMEX dimmer. With power off, close the circuit and restore

power. If the lights do not work or a breaker trips, check and correct the

wiring or fixture (if necessary). Install the dimmer only when the short

is no longer present. The warranty is void if the dimmer is installed and

operated with a shorted load.

CAUTION: TO REDUCE THE RISK OF OVERHEATING AND POSSIBLE

DAMAGE TO OTHER EQUIPMENT, DO NOT INSTALL TO CONTROL A

RECEPTACLE, A MOTOR-OPERATED APPLIANCE, A FLUORESCENT

LIGHTING FIXTURE, OR A TRANSFORMER-SUPPLIED APPLIANCE.

ATTENTION: GRADATEURS COMMANDANT UN BALLAST-AFIN DE RÉDUIRE

LE RISQUE DE SURCHAUFFE ET LA POSSIBILITÉ D’ENDOMMAGEMENT

À D’AUTRES MATÉRIELS, NE PAS INSTALLER POUR COMMANDER UNE

PRISE, UN APPAREIL D’ÉCLAIRAGE FLUORESCENT, UN APPAREIL OPÉRÉ

DE MOTEUR OU UN APPAREIL ALIMENTÉ PAR UN TRANSFORMATEUR.

NOTES: Observe the following points.

• Codes: This product should be installed and used in accordance with

appropriate electrical codes and regulations.

• Installation: This product should be installed by a qualified electrician.

• Wiring: Use copper wire only. For supply connections, use wires rated

for at least 75°C (167°F).

• Lamp Type: For control of permanently installed incandescent,

magnetic low voltage, or tungsten-halogen lamp fixtures only.

• Temperature: For use where temperatures are between 32° to 86°F (0°

to 30°C).

• Electrical Boxes: Devices mount in standard electrical boxes. For easy

installation, use 3-1/2 in. (89 mm) deep electrical boxes. Several devices

can be installed in one electrical box (multigang). This requires derating

of the dimming device. For a smooth appearance, one-piece multigang

faceplates (not supplied) must be installed. When installing into a

multigang box, do not fully tighten the devices to the box until the

faceplate has been aligned.

• Switches: Mechanical 3- or 4-way switches do not work with HZ-DIMEX

dimmers.

• Spacing: If mounting one device above another, leave at least 4-1/2 in.

(115 mm) vertical space between them.

• Low Voltage Applications: Use with core and coil (magnetic) low

voltage transformers only. Do not use any solid-state electronic low

voltage transformers. Operation of a low voltage circuit with all lamps

inoperative or removed may result in current flow in excess of normal

levels. To avoid transformer overheating and premature transformer

failure, Crestron recommends the following:

• Do not operate low voltage circuits without operative lamps in

place.

• Replace burned-out lamps as quickly as possible.

• Use transformers that incorporate thermal protection or fuse

transformer primary windings to prevent transformer failure due

to overcurrent.

Installation

Install the HZ-DIMEX:

1. Turn power off at the circuit breaker.

WARNING: If the HZ-DIMEX is used with an HZ-AUX or HZ-KPEX,

power may need to be turned off at multiple breakers.

2. Wire the device as shown in the following diagrams.

NOTE: To wire one or more HZ-AUX or HZ-KPEX, refer to the HZ-AUX

Quick Start (Doc. 8485) or the HZ-KPEX Quick Start (Doc. 8284) at

crestron.com/manuals.

STRIP LENGTH

LOAD HOT

REM

NEU

INSERT WIRES INTO ENTRY HOLES,

NOT BEHIND SCREW HEADS

CONTAINS:

FCC ID: EROCWD7712

IC: 5683C-CWD7712

120 VAC from

circuit breaker

To Loads

To one or

HZ-AUX or

HZ-KPEX

(optional)

To Ground

YesNo

Do not insert the wires behind the screw head. Insert

the wires into the wire entry holes.

3. Place the metal mounting bracket over the back of the HZ-DIMEX. The

two parts of the metal mounting bracket clip together which allows the

wiring to remain in place.

4. Fold the wires into the electrical box. Avoid pinched wires.

5. Secure the HZ-DIMEX to the electrical box using the integrated

mounting screws on the device. Ensure that the “Top” label is properly

oriented.

CAUTION: Do not overtighten the screws when attaching the keypad to

the electrical box, damage to the unit and undesired functionality may

occur.

6. Attach the HZ-FP-G series Horizon™ faceplate and magnetic trim

pieces (not supplied).

7. Ensure that all buttons actuate without sticking.

NOTE: To operate the device in Non-Dim mode, follow the instructions

in “Enable Non-Dim Mode.”

8. Restore power at the circuit breaker.

Single Gang Installation

Trim x2

(not supplied)

HZ-FP-G

Faceplate

(not supplied)

HZ-DIMEX

Electrical Box

(not supplied)

Wall

Metal Mounting Bracket

(not supplied)

Faceplate Mounting Screws (x4)

(not supplied)

Truss Head Screw x2

Multigang Installation

Truss Head Screw x2

HZ-DIMEX

Metal Mounting

Bracket

(not supplied)

Trim x2

(not supplied)

Spacer

HZ-FP-G2

Faceplate

(not supplied)

Wall

Electrical Box

(not supplied)

Faceplate Mounting Screws x4

(not supplied)

Multigang Installations

In multigang installations, several devices are grouped horizontally in one

electrical box. For a smooth appearance, use a 2-, 3-, or 4-gang HZ-FP-G

series Horizon™ faceplate (not supplied).

The load capacity for each device in the electrical box must be derated.

Refer to the following diagrams for derating information. The VA ratings

are for input power to the transformer. If you do not know the input power

requirement of the transformer, use the bulb’s wattage rating to determine

the proper rating.

Derating Information for HZ-DIMEX

750 VA

600 VA

300 VA

Changing the Dim Mode

The HZ-DIMEX can toggle between Dim and Non-Dim mode. In Non-Dim

mode, the device acts as a switch. This is useful if the load is not dimmable or

if it is preferred to not dim the load.

To switch between Dim and Non-Dim mode:

1. Slide the air-gap switch to the right, as described in “Disconnecting the

Power.”

2. To set the dimming mode:

• Non-Dim Mode: Press and hold the top button cap while the

power is off.

• Dim Mode: Press and hold the bottom button cap while the

power is off.

NOTE: If a side-to-side rocker is in the top or bottom position, either

side of the rocker can be pressed and held.

3. While holding the appropriate button, slide the air-gap switch to the

left to restore power to the device.

4. After all visible LEDs have flashed green once, release the button.

5. After the released button’s LED flashes green, the device will boot-up in

the selected dimming mode.

Operation

NOTE: Before using the HZ-DIMEX, ensure the device is using the

latest firmware. Check for the latest firmware for the HZ-DIMEX at

www.crestron.com/firmware. Firmware is loaded onto the device using either

Crestron Toolbox™ software or Crestron Home™ software.

Basic Operation

The operations in this guide assume the HZ-DIMEX is operating with Local

mode enabled (with or without a control system). The device can also operate

in Remote mode, in which the control system program dictates button

behavior and load control. The HZ-DIMEX is shipped with a rocker button

preinstalled, which functions as described below.

The LEDs behind the

button caps indicate the

load status.

Tap to turn on the

load. Press and hold

to raise the light

level.

Tap to turn off the

load. Press and hold

to lower the light

level.

HZ-DIMEX

Horizon™ In-Wall Forward-Phase Dimmer with infiNET EX® Wireless Communication, 120 VAC

Disconnect the Power

Power to the dimmer and load can be disconnected by using the air-gap

switch, which is located at the bottom of the device. Slide the air-gap switch to

the right to disconnect the power to the device and to the load, and slide the

switch to the left to restore power to both the device and the load.

NOTE: The switch must be in the left position for the device to operate.

Slide the air-gap switch to the

right to shut off power to the

unit and the load.

Default Button Functionality

The figure below illustrates the press and hold actuation sequences for each

local button option (selected in programming) when the Local button is

enabled. There is only one local button available per device.

If the Local button is disabled and control system communication is lost, the

device will default to the shown behavior for the local button. Button behavior

can be altered by the control system program. With the Local button enabled,

the selected local button can still act as a remote trigger. However, LED

feedback for the selected local button will be dictated only by the local load.

Default Local

Button

Single Press Double Press Hold

On Fast On Raise

Off Fast Off Lower

Toggle N/A Raise/Lower

NOTES:

• The default “On” powers the load to 100% in 1 second. The default

“Fast On” powers the load to 100% in 1/4 second. Load behavior for

“On” and “Fast On” operations can be modified when programming the

HZ-DIMEX .

• The single push button or side-to-to-side rocker can be designated as

the local button in any of the five available positions.

LED Behavior

The LEDs on the HZ-DIMEX display the state of the connected loads and are

located under each button cap.

Each LED can be in one of the following states:

NOTE: LED functionality for both local and remote behavior can be modified

when programming the device.

• On: The load is powered.

• Off: The load is not powered.

• Flashing: The load is ramping up or down.

Multiway Operation

For more information on multiway operation, refer to the HZ-AUX Quick Start

(Doc. 8485) or the HZ-KPEX Quick Start (Doc. 8284).

Wireless Communications

The device connects to the Crestron network via the infiNET EX

communications protocol. Use the following procedures to join or leave an

infiNET EX network and to verify communications between the device and the

control system.

NOTE: The HZ-DIMEX is not compatible with the MC3 internal gateway when

using channels 25 or 26.

Joining an infiNET EX Network

Before a device can be used in a lighting system, it must first join an infiNET EX

network by being acquired by an infiNET EX gateway.

NOTE: A device can be acquired by only one gateway.

1. Put the infiNET EX gateway into Acquire mode from the unit itself or

from Crestron Toolbox software, as described in the gateway’s manual

at www.crestron.com/manuals.

NOTE: In an environment where multiple gateways are installed, only

one gateway should be in Acquire mode at any time.

2. Place the device into Acquire mode.

a. Tap the top button three times, and then press and hold it down

(tap-tap-tap-press+hold) until all of the LEDs flash red once (this

can take up to 10 seconds).

NOTE: If a side -to-side rocker is in the top position, either side of the

rocker can be pressed and held.

b. Release the button to start the acquire process. The top button’s

LED flashes red slowly to show that the device is actively scanning

the infiNET EX network.

• The top button’s LED lights red for 5 seconds to show that the

device has been successfully acquired to the infiNET EX network.

• The top button’s LED flashes red quickly to indicate that the

device was not successfully acquired by the infiNET EX network.

Tap the setup button to acknowledge failure to acquire the

infiNET EX network. Ensure the gateway is in Acquire mode and

within range before attempting the acquire process again.

3. Once all devices have been acquired, take the gateway out of Acquire

mode. Refer to the gateway’s manual for details.

Leaving an infiNET EX Network

To leave an infiNET EX network, put the device into Acquire mode, as described

in “Joining an infiNET EX Network” above, when no gateway is in Acquire

mode.

Verifying Communications Status

To check the communications status of the device, tap the top button three

times and then press and hold it down (tap-tap-tap-press+hold) for up to 2

seconds. The button must be released before the LEDs flash to indicate the

communications status. Refer to the following table for details.

NOTES:

• If a side -to-side rocker is in the top position, either side of the rocker can

be pressed and held.

• If there is a communication error and a remote button is pressed, all

of the LEDs will flash red in one of the patterns described in the table

below.

LED Communications Status

Turns on for 5

seconds

The device is communicating with the control system.

Flashes three

times

The device is communicating with the gateway, but the

gateway is not communicating with the control system.

Flashes twice The device was previously joined to the network but is not

communicating with the gateway.

Flashes once The device is not joined to the network.

Ambient Light Sensor Calibration

An LED backlight behind each button illuminates engravings. The ambient

light sensor adjusts the backlight brightness according to the light level in the

room. The ambient light sensor can be affected by room conditions and should

be calibrated manually (locally or through programming), or the appropriate

setting can be changed in control system programming.

To locally calibrate the light sensor:

1. Ensure that all room lights are fully on.

2. Ensure the faceplate and bottom trim piece are installed correctly.

Remove the top trim piece.

3. Press and hold the setup button with a small pointed object until all

keypad backlights flash magenta (about 2 seconds). This can also be

triggered in programming.

4. Avoid blocking the light sensor on the bottom of the HZ-DIMEX. The

light sensor should remain unobstructed and free of direct light. After

about 5 seconds, the calibration process is complete. The keypad returns

to normal operation.

Setup

button

Backlight Customization

Backlight color customization can be accomplished locally or through

programming.

NOTE: Custom and preset color themes may be defined in the control system

program. Custom programming will override local settings.

To locally change the color of the LED backlights:

1. Press the setup button with a small pointed object once. The LED

backlights will light brightly for 15 seconds.

2. Press the setup button repeatedly to cycle through the backlight color

options.

Troubleshooting

The module displays error codes using the dimmer output LEDs. The LED

flashes a pattern to indicate the error on that output. For example, a 1-2 error

flashes the LED one time, pauses for 1 second, flashes two times, pauses for

2 seconds, and then repeats for 90 seconds (except where otherwise noted).

Refer to the following table for possible corrections.

Error

Code

Fault Name Fault Description

2-3 Over

Temperature

The dimmer has overheated and shut down due to

an excessive load. Verify that the total load matches

the proper ganged rating. The dimmer resumes

normal operation after cooling.

3-1 Zero Cross

Fault

The dimmer is unable to lock onto the AC line. If

the unit is powered by a generator, verify that the

generator output is 50/60 Hz and stable.

3-3 Device Error The device is experiencing a hardware issue. Please

contact Crestron Technical Support.

For general troubleshooting, please refer to the following table:

Trouble Probable Cause(s) Corrective Action

The

dimmer

does not

function.

The dimmer is not

receiving power.

Verify that the power connections are

correct and that the circuit breaker

is closed.

The load is not

operational (e.g. lamps

are burned out).

Verify that the load is operational and

that the airgap switch is closed.

The device is in Remote

mode.

Check the program to verify the

operating mode.

The air-gap is switched

to the right.

Ensure that the air-gap is switched

to the left.

The device has

overheated.

Verify that the device is loaded

properly for ganged configuration.

The neutral wire is

not connected to the

dimmer.

Connect a dedicated neutral wire to

the dimmer.

The

dimmer

does not

dim.

The device is in

Non-Dim mode.

Remove power from the device.

Reapply power and press and hold the

bottom button until all LEDs flash

green once.

Additional Information

Scan or click the QR code for detailed product information.

HZ-DIMEX

Compliance and Legal

Original Instructions: The U.S. English version of this document is the original instructions. All

other languages are a translation of the original instructions.

Regulatory Model: M201849003

Federal Communications Commission (FCC) Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures: Reorient or relocate the

receiving antenna; Increase the separation between the equipment and receiver; Connect the

equipment into an outlet on a circuit different from that to which the receiver is connected;

Consult the dealer or an experienced radio/TV technician for help.

To satisfy FCC RF Exposure requirements for mobile and base station transmission devices,

a separation distance of 20 cm or more should be maintained between the antenna of this

device and persons during operation. To ensure compliance, operation at closer than this

distance is not recommended. The antenna(s) used for this transmitter must not be co-

located or operating in conjunction with any other antenna or transmitter

CAUTION: Changes or modications not expressly approved by the manufacturer responsible

for compliance could void the user’s authority to operate the equipment.

Industry Canada (IC) Compliance Statement

CAN-ICES-3(B)/nmb-3 (B)

This device complies with Industry Canada license exempt RSS standard(s). Operation is

subject to the following two conditions: (1) this device may not cause interference, and (2)

this device must accept any interference, including interference that may cause undesired

operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils

radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1)

l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout

brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le

fonctionnement.

Under Industry Canada regulations, this radio transmitter may only operate using an antenna

of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada.

To reduce potential radio interference to other users, the antenna type and its gain should

be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that

necessary for successful communication.

Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut

fonctionner avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé

pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage

radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain

de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne

dépasse pas l’intensité nécessaire à l’établissement d’une communication satisfaisante

Intertek Compliance Statement

This product is listed to applicable UL Standards and requirements tested by Intertek services.

Ce produit est homologue selon les normes et les exigences UL applicables par Intertek

Prestations de service.

The product warranty can be found at www.crestron.com/warranty.

The specific patents that cover Crestron products are listed at

www.crestron.com/legal/patents.

Certain Crestron products contain open source software. For specific information, please

visit www.crestron.com/opensource.

Crestron, the Crestron logo, Crestron Home, Crestron Toolbox, Horizon, infiNET EX, and the

infiNET EX logo are either trademarks or registered trademarks of Crestron Electronics, Inc.

in the United States and/or other countries. Other trademarks, registered trademarks, and

trade names may be used in this document to refer to either the entities claiming the marks

and names or their products. Crestron disclaims any proprietary interest in the marks and

names of others. Crestron is not responsible for errors in typography or photography.

Crestron Electronics, Inc.

15 Volvo Drive, Rockleigh, NJ 07647

Tel: 888.CRESTRON

Fax: 201.767.7576

www.crestron.com

Quick Start - Doc. 8289A

(2054064)

09/26/19

Specifications subject to

change without notice.

Crestron HZ-DIMEX Quick Start

Marque: Crestron

Modèle: HZ-DIMEX

Catégorie: Gradateurs

Taper: Quick Start

Télécharger le PDF

rapport

dans d''autres langues

English: Crestron HZ-DIMEX

Crestron HZ-DIMEX Quick Start

Crestron HZ-DIMEX Quick Start

dans d''autres langues

Documents connexes

Autres documents