Crestron HZ-DIMEX Information produit

Taper
Information produit
HZ-DIMEX
Horizon™ In-Wall Forward-Phase Dimmer with infiNET EX® Wireless Communication, 120 VAC
DocType - 8612A
(2055107)
03.20
Getting Started
Scan the QR code to view the Quick Start Guide.
www.crestron.com/docs/8289
For additional information, visit
www.crestron.com/model/6509589.
Certification and Compliance
Regulatory Model: M201849003
Federal Communications Commission (FCC)
Compliance Statement
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses and
can radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference to
radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try
to correct the interference by one or more of the
following measures: Reorient or relocate the
receiving antenna; Increase the separation
between the equipment and receiver; Connect the
equipment into an outlet on a circuit different from
that to which the receiver is connected; Consult the
dealer or an experienced radio/TV technician for
help.
To satisfy FCC RF Exposure requirements for
mobile and base station transmission devices, a
separation distance of 20 cm or more should be
maintained between the antenna of this device and
persons during operation. To ensure compliance,
operation at closer than this distance is not
recommended. The antenna(s) used for this
transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
CAUTION: Changes or modifications not expressly
approved by the manufacturer responsible for
compliance could void the user's authority to
operate the equipment.
Industry Canada (IC) Compliance Statement
CAN ICES-3 (B)/NMB-3(B)
This device complies with Industry Canada license
exempt RSS standard(s). Operation is subject to
the following two conditions: (1) this device may
not cause interference, and (2) this device must
accept any interference, including interference that
may cause undesired operation of the device.
Le présent appareil est conforme aux CNR
d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux
deux conditions suivantes: (1) l'appareil ne doit pas
produire de brouillage, et (2) l'utilisateur de
l'appareil doit accepter tout brouillage
radioélectrique subi, me si le brouillage est
susceptible d'en compromettre le fonctionnement.
Under Industry Canada regulations, this radio
transmitter may only operate using an antenna of
a type and maximum (or lesser) gain approved for
the transmitter by Industry Canada. To reduce
potential radio interference to other users, the
antenna type and its gain should be so chosen that
the equivalent isotropically radiated power (e.i.r.p.)
is not more than that necessary for successful
communication.
Conformément à la réglementation d'Industrie
Canada, le présent émetteur radio peut
fonctionner avec une antenne d'un type et d'un
Crestron Electronics, Inc.
15 Volvo Drive, Rockleigh, NJ 07647
Tel: 888.CRESTRON
Fax: 201.767.7656
www.crestron.com
Product Information - Doc. 8612A
(2055107)
03/17/20
gain maximal (ou inférieur) approuvé pour
l'émetteur par Industrie Canada. Dans le but de
réduire les risques de brouillage radioélectrique à
l'intention des autres utilisateurs, il faut choisir le
type d'antenne et son gain de sorte que la
puissance isotrope rayonnée équivalente (p.i.r.e.) ne
dépasse pas l'intensité nécessaire à l'établissement
d'une communication satisfaisante.
Intertek Compliance Statement
This product is listed to applicable UL® Standards
and requirements tested by Interte services.
Ce produit est homologue selon les normes et les
exigences UL applicables par Intertek.
Legal
The product warranty can be found at
www.crestron.com/warranty.
The specific patents that cover Crestron products
are listed at www.crestron.com/legal/patents.
Certain Crestron products contain open source
software. For specific information, visit
www.crestron.com/opensource.
Crestron, the Crestron logo, Horizon, and infiNET
EX are either trademarks or registered trademarks
of Crestron Electronics, Inc. in the United States
and/or other countries. Intertek is either a
trademark or registered trademark of Intertek
Group in the United States and/or other countries.
The ETL logo is either a trademark or a registered
trademark of Intertek Testing Services NA in the
United States and/or other countries. UL is either a
trademark or a registered trademark of
Underwriters Laboratories, Inc. in the United States
and/or other countries. Other trademarks,
registered trademarks, and trade names may be
used in this document to refer to either the entities
claiming the marks and names or their products.
Crestron disclaims any proprietary interest in the
marks and names of others. Crestron is not
responsible for errors in typography or
photography.
©2020 Crestron Electronics, Inc.
  • Page 1 1
  • Page 2 2

Crestron HZ-DIMEX Information produit

Taper
Information produit

dans d''autres langues