GE GPT145SSLSS Le manuel du propriétaire

Marque: GE

Modèle: GPT145SSLSS

Catégorie: Lave-vaisselle

Taper: Le manuel du propriétaire

Write the model and serial

numbers here:

Model # _________________

Serial # _________________

You can find them on a label on

the tub wall just inside the door.

GE is a trademark of the General Electric Company. Manufactured under trademark license.

OWNER’S MANUAL

DISHWASHERS

49-55124-4 06-19 GEA

ENGLISH/FRANÇAIS/

ESPAÑOL

SAFETY INFORMATION .........3

USING THE DISHWASHER

Getting Started ........................5

Dispensers ............................6

Loading ..............................8

Connecting and disconnecting

(Portable models only) ................10

CARE AND CLEANING ............ 11

TROUBLESHOOTING TIPS ......14

LIMITED WARRANTY ...........17

CONSUMER SUPPORT ..........18

PDT145 Series - Built-In

GDT225-226 Series - Built-In

GPT145 Series - Portable

GPT225 Series - Portable

2 49-55124-4

THANK YOU FOR MAKING GE APPLIANCES A PART OF YOUR HOME.

Whether you grew up with GE Appliances, or this is your first, we’re happy to have you in the family.

We take pride in the craftsmanship, innovation and design that goes into every GE Appliances

product, and we think you will too. Among other things, registration of your appliance ensures that we

can deliver important product information and warranty details when you need them.

Consumer Support section of this Owner’s Manual. You may also mail in the pre-printed registration

card included in the packing material.

49-55124-4 3

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE

SAFETY INFORMATION

WARNING

For your safety, the information in this manual must be followed to minimize

the risk of fire, explosion, electric shock, and to prevent property damage, personal injury,

or death.

WARNING

PROPER INSTALLATION AND MAINTENANCE

This dishwasher must be properly installed and located in accordance with the Installation Instructions before

it is used. If you did not receive an Installation Instructions sheet with your dishwasher, you can receive one by

visiting our Website at GEAppliances.com. In Canada, visit www.GEAppliances.ca.

Connect the dishwasher/appliance to a grounded

metal, permanent wiring system; or run an

equipment-grounding conductor with the circuit

conductors and connect to the equipment-grounding

terminal or lead of the appliance.

Improper connection of the equipment-grounding

conductor can result in a risk of electric shock.

Check with a qualified electrician or service

representative if you are in doubt whether the

appliance is properly grounded.

Dispose of discarded appliances and shipping or

packing material properly.

Do not attempt to repair or replace any part of your

dishwasher unless it is specifically recommended in

this manual. All other servicing should be referred to

a qualified technician.

Use only cord kit WX09X70910 or hard-wire to

building electrical. Failure to follow this instruction,

could result in risk of fire and personal injury.

To minimize the possibility of electric shock,

disconnect this appliance from the power supply

before attempting any maintenance.

NOTE: Turning the dishwasher off does not

disconnect the appliance from the power supply.

We recommend having a qualified technician

service your appliance.

WARNING

WHEN USING YOUR DISHWASHER, FOLLOW BASIC PRECAUTIONS,

INCLUDING THE FOLLOWING:

Use this appliance only for its intended purpose as

described in this Owner’s Manual.

Use only detergents or wetting agents

recommended for use in a dishwasher and keep

them out of reach of children. Using a detergent

that is not specifically designed for dishwashers will

cause the dishwasher to fill with suds.

Locate sharp items so that they are not likely to

damage the door seal.

Load sharp knives with the handles up to reduce

the risk of cut-type injuries.

Do not wash plastic items unless marked

dishwasher safe or the equivalent. For plastic

items not so marked, check the manufacturer’s

recommendations.

Detailed grounding instructions can be found in the

“PREPARE ELECTRICAL WIRING” section of the

Installation Instructions.

Do not operate your dishwasher unless all

enclosure panels are properly in place.

Do not tamper with controls.

Do not abuse, sit on or stand on the door or dish

rack of the dishwasher.

Do not place objects on top of portable dishwasher.

Do not sit or stand on top of portable dishwasher.

To reduce the risk of injury, do not allow children to

play with, on or inside this appliance at any time.

Do not store or use combustible materials including

gasoline or other flammable liquids or vapors in the

vicinity of this or any other appliance.

Small parts can be a choke hazard to small children

if removed from the dishwasher. Keep out of reach

of small children.

READ AND SAVE THESE INSTRUCTIONS

4 49-55124-4

SAFETY INFORMATION

WARNING

WATER HEATER SAFETY

Under certain conditions, hydrogen gas may be produced in a water heater that has not been used for two or more weeks.

HYDROGEN GAS IS EXPLOSIVE.

If the hot water has not been used for two or more weeks, prevent the possibility of damage or injury by turning

on all hot water faucets and allowing them to run for several minutes. Do this before using any electrical

appliance connected to the hot water system. This simple procedure will allow any built-up hydrogen gas to

escape. Since the gas is flammable, do not smoke, use an open flame, or use the appliance during this process.

TO PREVENT MINOR INJURY AND PROPERTY DAMAGE

During or after wash cycle, contents may be hot to

the touch. Use care before handling.

Close supervision is necessary if this appliance is

used by or near children. Do not allow children to

play around the dishwasher when closing the door,

closing the upper rack, or while vertically adjusting

the upper rack due to the possibility of small fingers

being pinched.

Non-Dishware Items: Do not wash items such as

electronic air cleaner filters, furnace filters and

paint brushes in your dishwasher. Damage to the

dishwasher and discoloration or staining of the

dishwasher may result.

WARNING

RISK OF CHILD ENTRAPMENT

PROPER DISPOSAL OF THE DISHWASHER

Junked or abandoned dishwashers are dangerous…even if they will sit for “just a few days.” If you are getting

rid of your dishwasher, please follow the instructions below to help prevent accidents.

Do not allow children to play with, on, or inside this or any discarded appliance.

Take off the dishwasher countertop by removing the two front screws and sliding the countertop backwards.

Take off the door of the washing compartment.

CAUTION

ELECTRICAL REQUIREMENTS

Be sure that the electrical connection and wire size are adequate

and in conformance with the National Electric Code, ANSI/NFPA

70 – latest edition, and all local codes and ordinances.

This appliance must have:

120V, 60Hz, AC-only, 15-ampere or 20-ampere, fused

electrical supply.

Wiring must be 2 wire with ground and rated for 75°C (167°F).

If the electrical supply does not meet the above

requirements, call a licensed electrician before

proceeding.

It is recommended to have:

A circuit breaker or time-delay fuse.

A properly grounded individual branch circuit.

CAUTION

Ŷ ,I\RXUGLVKZDVKHULVFRQQHFWHGWRDZDOOVZLWFK

ensure that the switch is on prior to use.

Ŷ ,I\RXFKRRVHWRWXUQWKHZDOOVZLWFKRIIEHWZHHQ

wash cycles, allow 5-10 seconds after turning the

switch on before touching Start to allow the control

to initialize.

Ŷ 8VHRQO\SRZGHUFinish

Quantum

Automatic

Dishwashing Detergent, liquid detergents or rinse

agents recommended for use in a dishwasher and

keep them out of the reach of children. Finish

Quantum

Automatic Dishwashing Detergent, and

Finish

Jet-Dry

Rinse Aid rinse agents have been

approved for use in all GE Appliances dishwashers.

READ AND SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE

49-55124-4 5

USING THE DISHWASHER

Getting started

Features and appearance will vary throughout this manual

Select Cycle

Open the door and press the Cycle Select pad for the desired wash cycle. The light next to the Cycle Select

pad will be lit to indicate which wash cycle has been selected.

NOTE: Cycle times vary based on soil level, water temperature, and options selected.

The cycle must be selected with the door in the open position. The cycle will not start until the Start pad is

pushed and the door is closed within 4 seconds.

AutoSense This cycle automatically senses the soil level and adjusts the wash cycle accordingly. It is meant

for daily, regular, or typical use to completely wash a full load of normally soiled dishes and is

designed to conserve both water and energy. NOTE: AutoSense was used to rate the energy

efficiency of this dishwasher. *Time range: 1 hour 30 minutes - 2 hours.

Heavy This cycle is meant for heavily soiled dishes, cookware, pots, or pans with dried-on or baked-on

soils. Everyday dishes are safe to be used in this cycle. *Time: 2 hours 10 minutes.

Light This cycle is for lightly soiled dishes. It is safe for china and crystal with no options selected.

*Time: 48 minutes.

*Washing time only. Does not include drying time, Auto Hot Start, or options. NOTE: If the incoming water

temperature is too low, the Auto Hot Start feature may add up to 11 minutes of additional time.

Load Dishwasher

For best dishwashing results, follow the loading guidelines found in the Loading section. No pre-rinsing of

normal food soil is required. Scrape off hard soils, including bones, toothpicks, skins, and seeds. Remove

leafy vegetables, meat trimmings, and excessive amounts of grease or oil.

Add Detergent

Add needed amount of detergent to the detergent dispenser. Use detergent such as Finish

Quantum

Automatic Dishwashing Detergent. See Dispensers section.

Add Rinse Agent

Add rinse agent such as Finish

Jet-Dry

Rinse Aid to the rinse agent dispenser. See Dispensers section.

NOTE: The use of rinse aid can further enhance the dishwasher’s drying performance.

Select Options

Wash

Temp

Allows you to select a higher wash temperature. These options are only available for Heavy and

AutoSense cycles. Press the Wash Temp pad until the light next to the desired option comes on.

Boost

This option raises water temperature and extends cycle time in order to achieve better wash performance.

Sanitize

This option raises the water temperature in the final rinse to sanitize your dishware. The cycle length

may vary depending on the temperature of your inlet water.

NOTE: Cycles using this option are monitored for sanitization requirements. If the cycle is

interrupted during or after the main wash portion or if the incoming water temperature is so low that

adequate water heating cannot be achieved, the sanitizing conditions may not be met. In these

cases, the Sanitized light will not illuminate at the end of the cycle. Utilizing this option will modify

the cycle to meet the requirements of Section 6, NSF 184 for soil removal and sanitization efficacy.

NOTE: NSF certified residential dishwashers are not intended for licensed food establishments.

Delay

Start

This option allows you to delay the start of a wash cycle for up to 12 hours. With the door open

and a cycle selected, press the Delay Start pad to choose the number of hours you want to delay

the start of the wash cycle. The hours will show in the display window. NOTE: You may cancel the

Delay Start timer by holding the Start pad for 3 seconds. This will also cancel the wash cycle.

Control

Lock

You can lock the controls to prevent selections from being made. You can also lock the controls

after you have started a cycle to prevent cycle changes. For example, children cannot accidentally

start the dishwasher by pressing pads with this option selected.

To LOCK/UNLOCK the dishwasher control, press and hold the Cycle Select and Wash Temp

pads for 3 seconds. The lock control light ( ) will turn on to indicate the control is locked and will

turn off to indicate the control is unlocked.

Sanitized

Clean

Cycle

Select

Wash

Temp

Delay

Start

AutoSense

Heavy

Light

Boost

Sanitize

1-12 hrs

Start

Hold 3 Sec

Hold 3 Sec To Cancel

6 49-55124-4

Getting started

USING THE DISHWASHER

Start Dishwasher

Start Press the Start pad and close the door within 4 seconds to start the cycle or begin the Delay

Start countdown. The Start light will turn on. The wash cycle will begin after 10 seconds and

then pump out for 60 seconds prior to filling the dishwasher with water. To activate the display,

press any pad with the door open.

Interrupt

or Pause

To interrupt or pause a cycle, slowly open the door. Opening the door will cause the wash cycle

to pause. The dishwasher will beep every minute to remind you to close the door. To restart or

resume the cycle, press Start, and close the door within 4 seconds. If the door is not closed within

4 seconds, the Start light will start blinking and the dishwasher will beep once every minute to

signal that the cycle did not restart. If the Start light is blinking, the dishwasher is waiting for input.

Cancel To cancel a wash cycle, press and hold the Start pad for 3 seconds and close door.

The dishwasher w

ill drain, emit a beep sound, and the wash cycle light will turn off.

Indicator Lights

Sanitized Displayed at end of the cycle when Wash Temp - Sanitize has been selected and dishwasher

has met requirements for sanitization. See Wash Temp - Sanitize, for complete description.

Opening the door will turn off the light.

Clean Displayed when a wash cycle is complete. The light stays on as a reminder that the dishes are

clean. Opening the door will turn the light off.

Display

Time

Remaining

During operation, the display shows the total number of minutes remaining in the cycle. During a

delay start, the display will show hours of time remaining until the cycle starts.

Check the Water Temperature

The entering water should be at least 120°F (49°C) and

not more than 150°F (66°C) for effective cleaning and to

prevent dish damage. Check the water temperature with a

candy or meat thermometer.

Turn on the hot water faucet nearest the dishwasher,

place the thermometer in a glass and let the water run

continuously into the glass until the temperature stops

rising.

Use a Rinse Agent

Rinse agents, such as Finish

Jet-Dry

Rinse Aid are designed for great drying action and to protect against spots

and film build-up on your dishes, glasses, flatware, cookware, and plastic.

Filling the Rinse Agent Dispenser

The rinse agent dispenser holds 3.9 oz. (115 ml) of rinse agent. Under normal conditions, this will last approximately

one month.

Make sure the dishwasher door is fully open.

Open the dispenser door. (Rinse agent compartment is on the right side of dispenser.)

Slowly add rinse agent until the cup is full. You may need to pause several times to

allow rinse aid to settle.

Clean up any spilled rinse agent with a damp cloth to prevent foam from forming inside

the dishwasher.

Close the dispenser door.

Dispensers

To turn this option ON/OFF, press and hold the Start and Wash Temp buttons for 5 seconds, close the door and wait 3

minutes for the dishwasher to go into sleep mode. In the OFF mode, the control display, control sounds, and interior lights

(on some models) will not respond to the door opening/closing. This mode can be used when observing certain religious

holidays such as the Sabbath. To activate the control and interior lights (on some models), press any button.

Sabbath/Door Wake Up Mode

To turn the dishwasher control sounds ON/OFF, press the Wash Temp button 5 times within 5 seconds.

Mute

49-55124-4 7

USING THE DISHWASHER

Dispensers

Detergent Dispenser

To open, press the button and the cover will flip back.

The detergent dispenser has two compartments. The

pre-wash compartment is the smaller compartment on

the left side. Use the pre-wash compartment only when

your water is extremely hard or when you have a heavy

soiled load. The pre-wash compartment is not used

when tablet or packet detergents are used.

NOTE: Do not block detergent dispenser with large or

tall utensils.

You may use tablet, packet, powder, liquid or gel automatic

dishwasher detergent. Make sure you use only detergents

specifically labeled for use in automatic dishwashers. Never

use liquid hand dish detergent in an automatic dishwasher.

Sudsing and poor wash performance will result with the use

of improper detergents.

Detergents should be stored in a dry location and in their

original container to prevent loss of effectiveness. Place

detergent in the cup just prior to starting the dishwasher

and then close the cover. The cover will open during the

wash cycle.

Filling the Detergent Dispenser

We recommend using detergent in tablet or packet

form. Independent testing has shown this form of

detergent is very effective in the dishwasher. Finish

Quantum

Powerball

is an example of this type of

detergent. Simply put a tablet or packet into the main

wash compartment and close the detergent cup cover.

Please notice that the tablet or packet must be placed in

the main wash compartment of the detergent cup. If the

tablet or packet is placed in the prewash compartment or

tossed in the bottom of the dishwasher, the detergent will

be flushed down the drain in a very short period of time

and will thus be wasted. Wash performance will be very

poor as a result.

If you choose to use detergent in powder, liquid or gel

form, the amount of detergent you use will be determined

by the hardness of your water, the temperature of your

water, and the food soil load inside the dishwasher.

Contact your water company to get information about the

hardness of the water in your area. Water hardness is

measured in grains per gallon. Use this information and

the table above to determine the amount of detergent to

use. You may purchase a hard water test strip from

GE Appliances. Call 877-959-8688 and ask for part

number WD01X10295. In Canada, call 800-661-1616.

Use the table as a starting point and then adjust the

amount of detergent you use. Use just enough to get

good wash performance. Using just the right amount of

detergent will provide great wash performance without

wasting detergent or etching glassware.

Using too much detergent with very soft and/or very

hot water may cause a condition called etching on your

glassware. Etching is a permanent cloudiness in your

glassware. This condition is irreversible. However, using

too little detergent will cause poor wash performance.

DO NOT USE HAND DISH DETERGENT

NOTE: Using a detergent that is not specifically designed

for dishwashers will cause the dishwasher to fill with suds.

During operation, these suds will spill out of the dishwasher

vents, covering the kitchen floor and making the floor wet.

Because so many detergent containers look alike,

store the dishwasher detergent in a separate space

from all other cleaners. Show anyone who may use the

dishwasher the correct detergent and where it is stored.

While there will be no lasting damage to the dishwasher,

your dishes will not get clean using a dishwashing

detergent that is not formulated for automatic dishwashers.

Number of

Grains/Gal.

Detergent Cup(s) to Fill

Less than 5 Fill main cup to line 20

5 to 10 Fill main cup to line 30

Greater than 10

Fill both main cup

and pre-wash cup

Pre-Wash

Rinse

Agent

Main Wash

Detergent

Dispenser

8 49-55124-4

The upper rack may be adjusted to

accommodate larger

items.

To adjust the upper rack:

Fully extend the upper rack and rotate open the two plastic

end caps

on the front of the rails.

Remove the upper rack.

Select the set of rollers on the side of the rack that

provides the desired height, and reinstall the upper rack by

guiding the rack rails between the appropriate set of

rollers.

With the rack reinstalled, rotate closed the two plastic end

caps, ensuring

the snap is properly engaged. Failure to

properly engage the

end caps may result in the rack falling

from the dishwasher.

USING THE DISHWASHER

For best dishwashing results, follow these loading guidelines. Features and appearance of racks and silverware

baskets may vary from your model.

Upper Rack

The upper rack is for glasses, cups, and saucers. This

is also a secure place for dishwasher-safe plastic items.

The upper rack can be used for odd sized utensils.

Sauce pans, mixing bowls, and other similarly shaped

items should be placed face down for best wash

performance.

The cup shelf may be placed in the up or down position to

add flexibility.

IMPORTANT: Ensure that

items do not protrude through

the bottom of the rack where

they will block the rotation

of the upper spray arm. This

could result in noise during

operation and/or poor wash

performance.

A loaded upper rack may be heavier

than anticipated. To prevent minor

injury or damage to the contents, do not raise or lower

the upper rack after the rack is loaded.

CAUTION

Upper Rack - Adjustment

PDT145 Series

8 Place Settings

GDT225-226 Series

8 Place Settings 10 Place Settings 12 Place Settings

GDT225-226 Series GDT225-226 Series

End Cap

Rollers

Rail

Remove:

Rail

End

Cap

Replace:

Rollers

49-55124-4 9

USING THE DISHWASHER

For best dishwashing results, follow these loading guidelines. Features and appearance of racks and silverware

baskets may vary from your model.

Lower Rack

When loading the lower rack, do not load large platters

or trays in the front left. They may prevent detergent

from circulating during the wash cycle.

The lower rack is best used for plates, saucers and cookware.

Large items should go along the sides. Load platters, pots

and bowls along the sides, in corners or in the back. The

soiled side of items should face the center of the rack.

IMPORTANT: Ensure that items do

not protrude through the bottom of

the rack or the silverware basket

where they will block the rotation

of the lower spray arm. This could

result in noise during operation and/

or poor wash performance.

Silverware Basket

The silverware basket may be used without the topper

for quick loading. With the topper, flatware is better

positioned for the dishwasher to thoroughly wash and dry

all pieces by preventing nesting.

Without the topper

Put the flatware in the removable basket with fork and

knife handles up to protect your hands. Place spoons

in the basket with handles down. Mix knives, forks and

spoons so they don’t nest together. Distribute evenly.

Small plastic items, such as measuring spoons and lids

from small containers, should go in the bottom of the

silverware basket with silverware on top.

With the topper

Place small plastic items, such as measuring spoons and

lids from small containers, in the bottom of the basket

and snap the topper in place. Insert spoons and forks,

handles first, through the holes in the topper. Place

knives, blades first, through the holes in the topper.

IMPORTANT: Do not load large or tall utensils where they

may block the detergent dispenser or upper spray arm. This

could result in noise during operation and/or poor wash

performance.

Two-piece basket

To separate, grasp the basket at

opposite corners and slide apart.

PDT145 Series GDT225-226 Series

PDT145 Series

8 Place Settings

GDT225-226 Series

8 Place Settings 10 Place Settings 12 Place Settings

GDT225-226 Series GDT225-226 Series

10 49-55124-4

Connecting and disconnecting (Portable models only)

USING THE DISHWASHER

Depress collar to

release unicouple

from faucet

Remove Power

Ŷ

Unplug the dishwasher.

Ŷ

Feed power cord back into its storage location.

Remove Unicouple from Faucet

Ŷ

Turn off hot water.

Ŷ

Relieve water pressure from the unicouple assembly

before disconnecting it from the faucet by depressing

the red pressure relief button on the unicouple.

Ŷ

Depress the locking collar and remove the unicouple

from the faucet.

Ŷ

Drain excess water from the unicouple. If the sink is 34”

or higher from the floor, the excess water in unicouple

hoses cannot be drained directly into the sink. It will be

necessary to drain excess water from hoses into a bowl

or suitable container that is held outside and lower than

the sink.

Ŷ

Feed the unicouple and hoses back into their storage

pocket.

Store the Dishwasher

Ŷ

Latch the dishwasher door closed.

Ŷ

Roll the dishwasher into its storage location.

Disconnect and Store Your Dishwasher (Portable Models Only)

Ŷ

Run garbage disposer, if you have one, to clean out

the disposer and thus allow water to drain from the

sink through the disposer and down the drain.

Ŷ

Run hot water faucet to purge cold water from the hot

water line. The hot water must be between 120°F and

150°F for best wash performance.

Ŷ

Roll the dishwasher to a position just in front of the

sink.

Ŷ

Pull the unicouple and its hoses completely out from

storage compartment at rear of the dishwasher.

Ŷ

Attach the unicouple to the faucet adapter following the

three steps below:

- Depress the locking collar at the top of the unicouple.

- Place the unicouple completely over the faucet

adapter.

- Release the locking collar. The unicouple should now

be locked onto the faucet adapter.

Ŷ

Turn on the hot water faucet and check for leaks. If a

unicouple leak was observed, take whatever actions

are necessary to repair the leak. This may be as

simple as tightening the faucet adapter. Or, it may

require the services of a plumber if water is leaking

from the interface between the moveable faucet arm

and the fixed part of the faucet fastened to the sink.

NOTE: The unicouple’s small hose carries water from

the faucet to the dishwasher. The large hose carries

water from the dishwasher to the sink. Orient the faucet

with the unicouple attached so water from the unicouple

will run into the sink drain.

Ŷ

Plug the dishwasher power cord into the electrical

outlet.

Connect the Unicouple to the Faucet (Portable Models Only)

Collar

Depress red button to

release water pressure

49-55124-4 11

Care and cleaning

CARE AND CLEANING

Control Panel

To clean the control panel, use a lightly dampened cloth. Then dry thoroughly.

Exterior Door Panel

Before cleaning the front panel, make sure you know what type

of panel you have. Refer to the last two letters of your model

number. You can locate your model number on the left-hand tub

wall just inside the door. If your model number ends with BB or

WW then you have a painted door panel. If your model number

ends with SS, then you have a Stainless Steel door panel.

Follow the instructions below for cleaning the door panel

for your specific model.

Painted Door Panel (model numbers ending in

BB–black or WW–white)

Use a clean, soft, lightly dampened cloth, then dry thoroughly

Do not use scouring pads or powered cleaners because

these products can scratch the finish.

Stainless Steel Door Panel (model numbers ending in SS)

For cleaning rust and tarnish, cleaners with oxalic acid

such as Bar Keepers Friend Soft Cleanser™ will remove

rust, tarnish and small blemishes. Use only a liquid

cleanser free of grit and rub in the direction of the brush

lines with a damp soft sponge. Do not use appliance wax

or polish on the stainless steel.

For other blemishes and marks, use Stainless Steel

Magic or a similar product using a clean soft cloth. Do not

use appliance wax, polish, bleach or products containing

chlorine on Stainless Steel. You can order Stainless Steel

Magic # WX10X29 through GE Appliances Parts by

calling 877.959.8688. In Canada, call 800-661-1616.

Spray Arms

Because hard water chemicals will clog the spray arm jets and

bearings, it is necessary to clean the spray arms regularly.

Wash the arms in soapy, warm water and use a soft brush

to clean the jets. Replace them after rinsing thoroughly.

Upper Spray Head

Do NOT remove the upper spray head.

Clean with warm soapy water using a small plastic bristle

brush.

Retaining nut

Upper

Rack

Water Supply Tube

Upper Spray Arm

To remove the upper spray arm, twist the retaining nut

45° and pull the spray arm off the water supply tube.

To remove the lower spray arm, remove the lower rack

and lift spray arm out.

IMPORTANT: When replacing make sure to twist lock

the retaining nut securely onto the water supply tube.

Check that the spray arm is secure and that it rotates

freely.

IMPORTANT: When replacing make sure to seat the

arm clips over the retaining ring. Check that the spray

arm is secure and that it rotates freely.

Lower Spray Arm

Arm

Clips

Retaining

Ring

Dishwasher Interior

To clean and de-odorize your dishwasher, use citric acid

or Finish

Dishwasher Cleaner, a detergent additive.

Finish

Dishwasher Cleaner will break up mineral

deposits, and remove hard water film and stains.

You can order citric acid GE Appliances kit #WD35X151

through GE Appliances Parts by calling 877-959-8688

or visiting GEApplianceparts.com. In Canada, call

800-661-1616. You can purchase Finish

Dishwasher

Cleaner at your local grocery store.

12 49-55124-4

Care and cleaning

CARE AND CLEANING

Filter Assembly

Inspect and clean the filters periodically. This should be done every month or more depending on usage. If there is a

decrease in wash performance or dishes feel gritty, this is also an indication the filters need to be cleaned.

To clean the filter assembly, remove the bottom

rack and lower spray arm. Twist the filter assembly

counterclockwise and lift to remove. Remove the filter

plate.

Rinse the filters with warm soapy water. Scouring pads

or brushes can scratch the filter surfaces but a soft brush

or sponge may be needed to remove stubborn soils or

calcium deposits caused by hard water.

Once cleaned, replace the filter plate, insert the filter

assembly through the plate and twist it clockwise until

it locks in place. Make sure the filters are fully seated

as improper replacement of the filters may reduce the

performance level of the appliance. Replace the lower

spray arm and lower rack.

Filter

Plate

Filter Assembly

Lower

Spray Arm

Stainless Steel Inner Door and Tub

The stainless steel used to make the dishwasher tub and

inner door provides the highest reliability available in a

GE Appliances dishwasher.

If the dishwasher tub or inner door should be scratched

or dented during normal use, they will not rust or

corrode. These surface blemishes will not affect their

function or durability.

Twist

counterclockwise

and lift to remove

Replace the filter plate.

Snap the fine filter back

into the coarse filter.

Place filter assembly

through the filter plate

and twist clockwise to

lock into the dishwasher

Press tabs on

the fine filter

and pull to

separate from

the coarse filter

Fine Filter

Coarse Filter

Filter Plate

IMPORTANT: Before replacing, make sure no objects have

fallen into the opening in the bottom of the dishwasher.

49-55124-4 13

Care and cleaning

CARE AND CLEANING

Does Your Dishwasher Have an Air Gap? (Built-In Models Only)

An air gap protects your dishwasher

against water backing up into it if a drain

clogs. The air gap is not a part of the

dishwasher. It is not covered by your

warranty. Not all plumbing codes require

air gaps, so you may not have one.

The air gap is easy to clean.

Turn off the dishwasher and lift off the air gap cover.

Remove the plastic cap under the cover and clean with a

toothpick.

Replace the cap and cover when the air gap is clean.

Check the air gap any

time your dishwasher

isn’t draining well.

Air gap

Protect Against Freezing (Built-In Models Only)

If your dishwasher is left in an unheated place during the

winter, ask a service technician to:

Turn off electrical power to the dishwasher. Remove

fuses or trip circuit breaker.

Turn off the water supply and disconnect the water inlet

line from the water valve.

Drain water from the water inlet line and water valve.

(Use a pan to catch the water.)

Reconnect the water inlet line to the water valve.

Protect Against Freezing (Portable Models Only)

If your dishwasher is left in an unheated place during the

winter, ask a service technician to:

Unplug the dishwasher from the wall outlet.

Turn the water off and remove the Unicouple from the

faucet.

Drain water from the Unicouple hose. (Use a pan to

catch the water.)

14 49-55124-4

Problem Possible Cause What To Do

Start status indicator

light flashing

The door was opened or the

cycle was interrupted.

Press the Start pad once and close the door within 4

seconds to start the dishwasher. Press the Start pad a

second time when the dishwasher is running only if you

wish to cancel the cycle.

Dishwasher BEEPS

once every minute

This is a reminder that your

dishwasher door has been left

open during operation. It will

continue beeping until you

press Start and close the door.

Press Start and close the door.

Beeping at the end

of the cycle

This is normal. Dishwasher

will beep at end of cycle.

The dishwasher will beep (unless interupted) and the

Clean light will display at the end of the wash cycle.

Dishes and flatware

not clean

Filter assembly is clogged See the CARE AND CLEANING section.

Low inlet water temperature Make sure inlet water temperature is correct (see the

USING THE DISHWASHER section). Turn on the hot

water faucet nearest the dishwasher, let run until the water

temperature stops rising. Then start the dishwasher and

turn off the faucet. This ensures the entering water is hot.

Select Wash Temp - Boost.

Water pressure is

temporarily low

Turn on a faucet. Is water coming out more slowly than usual?

If so, wait until pressure is normal before using your dishwasher.

Normal water pressure to the dishwasher should be 20-120 psi.

Air gap or disposer clogged

(Built-In Models Only)

Clean the air gap or flush the disposer.

High drain loop or air

gap not installed (Built-In

Models Only)

Refer to the Installation Instructions for proper drain line

installation.

Improper rack loading Make sure large dishware or utensils do not block detergent

dispenser or the wash arms. See the Loading section.

Poor performing detergent Use a highly rated detergent such as Finish

Quantum

Automatic Dishwashing Detergent.

Spots and filming

on glasses and

flatware

Extremely hard water Use rinse agents such as Finish

Jet-Dry

Rinse Aid to

prevent spots and prevent new film build-up.

If water is extremely hard, a softener may be required.

Low inlet water temperature Make sure inlet water temperature is at least 120°F (49°C).

Overloading or improper

loading of the dishwasher

Load dishwasher as shown in the Loading section.

Old or damp powder

detergent

Make sure detergent is fresh. Use a highly rated

detergent such as Finish

Quantum

Automatic

Dishwashing Detergent

Rinse agent dispenser empty

Refill with rinse agent such as Finish

Jet-Dry

Rinse Aid.

Too little or low performing

detergent

Make sure you use the proper amount of highly rated

detergent.

Cloudiness on

glassware

Combination of soft water

and too much detergent

This is called etching and is permanent. To prevent this

from happening, use less detergent if you have soft water.

Wash glassware in the shortest cycle that will get it clean.

Low performing phosphate-

free detergent

See A white film on glassware, dishware and the

interior in this TROUBLESHOOTING TIPS section.

Water temperature entering

the dishwasher exceeds

150°F (66°C)

This could be etching. Lower the water heater

temperature.

Suds in the tub Wrong detergent Use only automatic dishwasher detergents to avoid sudsing.

Finish

Quantum

Automatic Dishwashing Detergent has

been approved for use in all GE Appliances dishwashers.

Rinse agent was spilled Always wipe up rinse agent spills immediately.

TROUBLESHOOTING TIPS

Troubleshooting Tips... Before you call for service

49-55124-4 15

Troubleshooting Tips... Before you call for service

TROUBLESHOOTING TIPS

Problem Possible Cause What To Do

Detergent left in

dispenser cups

Dishes or utensils are

blocking the detergent cup

Reposition the dishes, so the water from the lower spray

arm can flush the detergent cup. See the Loading section.

Reposition the tall utensils or heavy silverware that may

be keeping the dispenser cup door from opening. See

the Loading section.

Black or gray marks

on dishes

Aluminum utensils have

rubbed against dishes

Remove marks with a mild, abrasive cleaner.

Dishes don’t dry

Door not opened immediately

after Clean light came on

For proper drying, the dishwasher door must be opened

immediately after the Clean light comes on.

Low inlet water temperature Make sure inlet water temperature is at least 120°F.

Use Wash Temp Boost.

Select a higher cycle, such as Heavy.

Rinse agent dispenser is

empty

Check the rinse agent dispenser and fill as required.

Control panel

responded to inputs

but dishwasher

never filled with

water

Door may not be completely

closed

Make sure the door is firmly closed.

Water valve may be turned

off

Make sure water valve (usually located under the sink) is

turned on.

Stained tub interior An overall yellow or brown

film can be caused by iron

deposits in water

A special filter in the water supply line is the only way to

correct this problem. Contact a water softener company.

White film on inside

surface— hard water

minerals

We recommend

Finish

Jet-Dry

Rinse Aid

to help

prevent hard water mineral deposits from forming.

Run dishwasher with citric acid to remove mineral

deposits. Citric acid (Part number: WD35X151) can be

ordered through GE Appliances Parts. See back cover

for ordering information. Alternatively, purchase Finish

Dishwasher Cleaner and follow the directions on the

label.

Dishwasher won’t

run

Fuse is blown or circuit

breaker is tripped

Replace fuse or reset circuit breaker. Remove any other

appliances from the circuit.

Power is turned off In some installations, the power to the dishwasher is

provided through a wall switch, often located next to the

disposer switch. Make sure it is on.

Control panel is locked Unlock control panel. See the Getting started section.

Reboot your control Turn off power to the dishwasher (at circuit breaker or

wall switch) for 30 seconds, then turn back on.

Control panel lights

go off when you’re

setting controls

Time too long between

touching of selected pads

Each pad must be touched within 30 seconds of the

others. To relight, touch any pad again or open the door

and unlock.

Water standing in

the bottom of the

tub (Built-In Models

Only)

Air gap is clogged Clean the air gap. See the Care and cleaning section.

High drain loop or air gap

not installed

Refer to the Installation Instructions for proper drain line

installation.

Water won’t pump

out of the tub

Drain is clogged If you have an air gap, clean it. See the Care and

cleaning section. (Built-In Models Only)

If the dishwasher drains into a disposer, run disposer clear.

Check to see if your kitchen sink is draining well. If not,

you may need a plumber.

16 49-55124-4

Problem Possible Cause What To Do

Sanitized light does

not illuminate at the

end of the cycle

The door was opened and

the cycle was interrupted

during final rinse

Do not interrupt the cycle by opening the door during the

wash cycle.

The incoming water

temperature was too low

Raise the water heater temperature to between 120°F

and 150°F.

Noise Normal operating sounds:

Beeping at the end of the

cycle

Detergent cup opening

Water entering dishwasher

Motor stops and starts at

various times during cycle

Spray arms start and stop

at various times

Drain pump sounds during

pump out

Drain pump starts and

stops several times during

each drain

These are all normal. No action is required.

Rattling dishes when the

spray arm rotates

Make sure dishes are properly loaded. See the Loading

section.

Rattling silverware against

door during wash

Tall utensils may be placed in the upper rack to avoid

bumping against inner door during wash cycle.

A white film on

glassware, dishware

and the interior

This problem is likely

caused by a low quality

phosphate-free dishwasher

detergent

To remove the white film, run your dishes through a

dishwasher cycle with citric acid. Use a WD35X151

citric acid kit found online. Otherwise, use Finish

Dishwasher Cleaner found at your local grocery store.

Pour the citric acid in the detergent cup and close the

cover. Place the filmed but otherwise clean glassware and

dishware in the dishwasher. Leave silverware and other

metal items out of the dishwasher. Turn the dishwasher on

and let it run through a complete cycle without detergent.

The glassware, dishware, and dishwasher should come out

film free. Alternatively, a vinegar rinse may be used. Pour 1

cup of vinegar into dishwasher just after the detergent cup

opens and let the dishwasher complete its cycle.

This may be repeated several times a year as needed.

The use of a rinse agent such as

Finish

Jet-Dry

Rinse Aid

may help minimize a repeat build up of film.

Also, the use of a highly rated detergent such as

Finish

Quantum

Automatic Dishwashing Detergent will help

prevent film build-up.

TROUBLESHOOTING TIPS

Troubleshooting Tips... Before you call for service

Open the door to interrupt the cycle. Pull the door

handle to release the door.

Do not open the door all the way until the water spray

action stops. Steam may rise out of the dishwasher.

Add additional items.

Press Start and close the door within 4 seconds to

resume the cycle.

Forget to Add a Dish?

Additional items may be added to the dishwasher at any time, ideally items would be added shortly after starting a

wash cycle.

49-55124-4 17

LIMITED WARRANTY

GE Appliances Dishwasher Limited Warranty

Staple your receipt here. Proof of the original purchase

date is needed to obtain service under the warranty.

GEAppliances.com

All warranty service is provided by our Factory Service Centers, or an authorized Customer Care

technician. To schedule

service online, visit us at GEAppliances.com/service, or call GE Appliances at 800.GE.CARES (800.432.2737). Please

have your serial number and your model number available when calling for service.

Servicing your appliance may require the use of the onboard data port for diagnostics. This gives a GE Appliances factory

service technician the ability to quickly diagnose any issues with your appliance and helps GE Appliances improve its

products by providing GE Appliances with information on your appliance. If you do not want your appliance data to be

sent to GE Appliances, please advise your technician not to submit the data to GE Appliances at the time of service.

Extended Warranties: Purchase a GE Appliances extended warranty and learn about special discounts that are

available while your warranty is still in effect. You can purchase it online anytime at

GEAppliances.com/extended-warranty

or call 800.626.2224 during normal business hours. GE Appliances Service will still be there after your warranty expires.

In the United States:

This limited warranty is extended to the original purchaser and any succeeding owner for products purchased for home use

within the USA. If the product is located in an area where service by a GE Appliances Authorized Servicer is not available,

you may be responsible for a trip charge or you may be required to bring the product to an Authorized GE Appliances

Service location for service. In Alaska, the limited warranty excludes the cost of shipping or service calls to your home.

Some states do not allow the exclusion or limitation of incidental or consequential damages. This limited warranty

gives you specific legal rights, and you may also have other rights which vary from state to state. To know what your

legal rights are, consult your local or state consumer affairs office or your state’s Attorney General.

Warrantor: GE Appliances, a Haier Company

Louisville, KY 40225

EXCLUSION OF IMPLIED WARRANTIES

Your sole and exclusive remedy is product repair as provided in this Limited Warranty. Any implied warranties,

including the implied warranties of merchantability or fitness for a particular purpose, are limited to one year or the

shortest period allowed by law.

In Canada:

This limited warranty is extended to the original purchaser and any succeeding owner for products purchased in Canada

for home use within Canada. If the product is located in an area where service by a GE Appliances Authorized Servicer is

not available, you may be responsible for a trip charge or you may be required to bring the product to an Authorized

GE Appliances Service location.

Some provinces do not allow the exclusion or limitation of incidental or consequential damages. This limited warranty

gives you specific legal rights, and you may also have other rights which vary from province to province. To know what

your legal rights are, consult your local or provincial consumer affairs office.

Warrantor: MC Commercial Inc., Burlington, ON, L7R 5B6

For the period of: We will replace:

One year

From the date of the

original purchase

Any part of the dishwasher which fails due to a defect in materials or workmanship.

During this limited one-year warranty, we will also provide, free of charge, all labor

and related service to replace the defective part.

What is not covered:

Service trips to your home to teach you how to use

the product.

Improper installation, delivery or maintenance.

Failure of the product if it is abused, misused, or used for

other than the intended purpose or used commercially.

Replacement of house fuses or resetting of circuit

breakers.

Products which are not defective or broken, or which

are working as described in the Owner’s Manual.

Damage to the product caused by accident, fire,

floods or acts of God.

Incidental or consequential damage caused by

possible defects with this appliance.

Defects or damage due to operation in freezing

temperatures.

Damage caused after delivery including damage from

items dropped on the door.

Product not accessible to provide required service.

Cleaning or servicing of the air gap (Built-In Models

Only) device in the drain line.

18 49-55124-4

Consumer Support

CONSUMER SUPPORT

GE Appliances Website

Have a question or need assistance with your appliance? Try the GE Appliances Website 24 hours a day, any day

of the year! You can also shop for more great GE Appliances products and take advantage of all our on-line support

services designed for your convenience. In the US: GEAppliances.com

communication and prompt service under the terms of your warranty, should the need arise. You may also mail in

the pre-printed registration card included in the packing material. In the US: GEAppliances.com/register

Schedule Service

Expert GE Appliances repair service is only one step away from your door. Get on-line and schedule your service at

your convenience any day of the year. In the US: GEAppliances.com/service

or call 800.432.2737 during normal business hours.

Extended Warranties

Purchase a GE Appliances extended warranty and learn about special discounts that are available while your

warranty is still in effect. You can purchase it on-line anytime. GE Appliances Services will still be there after your

warranty expires. In the US: GEAppliances.com/extended-warranty

or call 800.626.2224 during normal business hours.

Remote Connectivity

For assistance with wireless network connectivity (for models with remote enable),

visit our website at GEAppliances.com/connected-home-smart-appliances/ or call 800.220.6899 in the US.

Parts and Accessories

Individuals qualified to service their own appliances can have parts or accessories sent directly to their homes

(VISA, MasterCard and Discover cards are accepted). Order on-line today 24 hours every day.

In the US: GEApplianceparts.com or by phone at 877.959.8688 during normal business hours.

Instructions contained in this manual cover procedures to be performed by any user. Other servicing

generally should be referred to qualified service personnel. Caution must be exercised, since improper

servicing may cause unsafe operation.

If you are not satisfied with the service you receive from GE Appliances, contact us on our Website with all the

details including your phone number, or write to:

In the US: General Manager, Customer Relations | GE Appliances, Appliance Park | Louisville, KY 40225

GEAppliances.com/contact

Printed in China

Inscrivez ci-dessous les numéros

de modèle et de série

N° de modèle ____________

N° de série ______________

Ils se trouvent sur la paroi de la

cuve, à l’intérieur de la porte.

GE est une marque déposée de General Electric Company. Fabriqué sous licence de marque.

MANUEL

D’UTILISATION

LAVE-VAISSELLE

CONSIGNES DE SÉCURITÉ .......3

UTILISATION DU LAVE-

VAISSELLE

Comment démarrer ....................5

Distributeurs ..........................6

Chargement ...........................8

Branchement et débranchement

(Modèles portables uniquement) .......10

ENTRETIEN ET NETTOYAGE ... 11

CONSEILS DE DÉPANNAGE .....14

GARANTIE LIMITÉE ..............17

SERVICE À LA CLIENTÈLE ......18

PDT145 Séries - Modèle intégré

GDT225-226 Séries - Modèle intégré

GPT145 Séries - Modèle portable

GPT225 Séries - Modèle portable

49-55124-4 06-19 GEA

2 49-55124-4

NOUS VOUS REMERCIONS D’ACCUEILLIR GE APPLIANCES CHEZ VOUS

Que vous ayez grandi avec GE Appliances ou qu’il s’agisse de votre première acquisition, nous

sommes heureux de vous accueillir dans notre famille.

Nous sommes fiers du savoir-faire, de l’innovation et de l’esthétique qui composent chaque appareil

GE Appliances, et nous pensons que vous le serez aussi. Dans cette optique, nous vous rappelons

que l’enregistrement de votre électroménager vous assure la communication de renseignements

importants sur le produit et la garantie lorsque vous en avez besoin.

Enregistrez votre électroménager GE en ligne dès maintenant. Des sites Web et des numéros de

téléphone utiles figurent dans la section Soutien au consommateur de ce manuel d’utilisation. Vous

pouvez aussi poster la fiche de garantie préimprimée incluse dans l’emballage.

La page est en cours de chargement...

GE GPT145SSLSS Le manuel du propriétaire

Marque: GE

Modèle: GPT145SSLSS

Catégorie: Lave-vaisselle

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: GE GPT145SSLSS Owner's manual
español: GE GPT145SSLSS El manual del propietario

GE GPT145SSLSS Le manuel du propriétaire

GE GPT145SSLSS Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents