Schumacher NAPA 90-300A Automatic Battery Charger/Maintainer Le manuel du propriétaire

Marque: Schumacher

Modèle: NAPA 90-300A Automatic Battery Charger/Maintainer

Catégorie: Chargeurs de batterie

Taper: Le manuel du propriétaire

0099001810-01

OWNER’S MANUAL

MANUAL DEL USUARIO

GUIDE D’UTILISATION

MODEL / MODELO / MODÈLE :

90-300A

Automatic Battery Charger/Maintainer

Cargador de batería automático / Mantenedor

Chargeur de batterie automatique / Mainteneur

PLEASE SAVE THIS OWNERS MANUAL AND READ BEFORE EACH USE.

This manual will explain how to use the charger safely and effectively. Please read

and follow these instructions and precautions carefully.

POR FAVOR CONSERVE ESTE MANUAL DEL USUARIO Y LEALO ANTES

DE CADA USO. En este manual le explica cómo utilizar el cargador de manera

segura y conable. Por favor, lea y siga las siguientes instrucciones y precauciones.

ESSAYER DE GARDER LE MANUEL D’INSTRUCTIONS ET LE LIRE AVANT

CHAQUE UTILISATION. Ce manuel explique comment utiliser l’unité d’une façon

sûre et efcace. S’il vous plaît lisez et suivez ces instructions et précautions.

CONTENTS

IMPORTANT SAFETY INSTRUCTIONS .................................................................................... 5

PERSONAL SAFETY PRECAUTIONS ....................................................................................... 6

PREPARING TO CHARGE ......................................................................................................... 6

CHARGER LOCATION ............................................................................................................... 7

DC CONNECTION PRECAUTIONS ........................................................................................... 7

FOLLOW THESE STEPS WHEN BATTERY IS INSTALLED IN VEHICLE ................................ 7

FOLLOW THESE STEPS WHEN BATTERY IS OUTSIDE VEHICLE ........................................ 8

GROUNDING AND AC POWER CORD CONNECTIONS .......................................................... 8

ASSEMBLY INSTRUCTIONS ..................................................................................................... 9

MOUNTING INSTRUCTIONS ..................................................................................................... 9

LED INDICATORS ...................................................................................................................... 9

OPERATING INSTRUCTIONS ................................................................................................. 10

MAINTENANCE AND CARE ..................................................................................................... 12

TROUBLESHOOTING .............................................................................................................. 13

BEFORE RETURNING FOR REPAIRS .................................................................................... 13

SPECIFICATIONS .................................................................................................................... 14

ACCESSORIES ........................................................................................................................ 14

LIMITED WARRANTY............................................................................................................... 14

CONTENIDOS

INSTRUCCIONES IMPORTANTES DE SEGURIDAD ............................................................. 16

PRECAUCIONES DE SEGURIDAD PERSONAL..................................................................... 17

PREPARACIÓN PARA LA CARGA .......................................................................................... 18

UBICACIÓN DEL CARGADOR................................................................................................. 18

PRECAUCIONES DE CONEXIÓN EN CC ............................................................................... 18

SIGA ESTOS PASOS CUANDO LA BATERÍA ESTÉ COLOCADA EN EL VEHÍCULO ............ 19

SIGA ESTOS PASOS CUANDO LA BATERÍA SE ENCUENTRE FUERA DEL VEHÍCULO .... 20

CONEXIONES A TIERRA Y ENERGÍA DE CA ......................................................................... 20

INSTRUCCIONES DE ENSAMBLE .......................................................................................... 21

INSTRUCCIONES DE MONTAJE ............................................................................................ 21

INDICADORES LED ................................................................................................................. 22

INSTRUCCIONES DE OPERACIÓN ........................................................................................ 22

MANTENIMIENTO Y CUIDADO ............................................................................................... 25

LOCALIZACIÓN Y SOLUCIÓN DE PROBLEMAS ................................................................... 25

ANTES DE DEVOLVER A REPARACIONES............................................................................ 26

ESPECIFICACIONES ............................................................................................................... 27

ACCESORIOS .......................................................................................................................... 27

GARANTÍA LIMITADA ............................................................................................................... 27

TABLE DES MATIÈRES

CONSIGNES DE SÉCURITÉ IMPORTANTES ......................................................................... 29

MESURES DE SÉCURITÉ PERSONNELLE ............................................................................ 30

PRÉPARATION POUR LE CHARGEMENT .............................................................................. 31

EMPLACEMENT DU CHARGEUR ........................................................................................... 31

PRÉCAUTIONS SUR LA CONNEXION C.C. ........................................................................... 31

ÉTAPES À SUIVRE QUAND LA BATTERIE EST INSTALLÉE DANS UN VÉHICULE ............. 32

ÉTAPES À SUIVRE QUAND LA BATTERIE EST INSTALLÉE HORS DU VÉHICULE ............ 33

MISE À LA TERRE ET CORDON D’ÉNERGIE CA ................................................................... 33

DIRECTIVES D’ASSEMBLAGE ................................................................................................ 34

DIRECTIVES DE MONTAGE .................................................................................................... 34

INDICATEURS LED .................................................................................................................. 35

CONSIGNES D’UTILISATION .................................................................................................. 35

CONSIGNES D’ENTRETIEN ................................................................................................... 38

TABLEAU DE DÉPANNAGE ..................................................................................................... 38

AVANT DE RETOURNER POUR REPARATION ...................................................................... 39

SPÉCIFICATIONS .................................................................................................................... 39

ACCESSOIRES ........................................................................................................................ 39

GARANTIE LIMITÉE ................................................................................................................. 40

• 5 •

1. IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS.

1.1 SAVE THESE INSTRUCTIONS – This manual contains important safety and

operating instructions.

1.2 This charger is not intended for use by children.

1.3 Do not expose the charger to rain or snow.

1.4 Use of an attachment not recommended or sold by the battery charger

manufacturer may result in a risk of re, electric shock or injury to persons.

1.5 To reduce the risk of damage to electric plug and cord, pull by the plug rather

than the cord when disconnecting charger.

1.6 An extension cord should not be used unless absolutely necessary. Use of

improper extension cord could result in a risk of re and electric shock. If an

extension cord must be used, make sure:

• The pins on plug of extension cord are the same number, size and shape as

those of plug on charger.

• The extension cord is properly wired and in good electrical condition.

• The wire size is large enough for AC ampere rating of charger, as specied in section 8.

1.7 Do not operate charger with damaged cord or plug – replace the cord or plug immediately.

1.8 Do not operate charger if it has received a sharp blow, been dropped, or

otherwise damaged in any way; take it to a qualied serviceman.

1.9 Do not disassemble charger; take it to a qualied serviceman when service or repair

is required. Incorrect reassembly may result in a risk of electric shock or re.

1.10 To reduce risk of electric shock, unplug charger from outlet before attempting any

maintenance or cleaning. Turning off controls will not reduce this risk.

1.11 WARNING: RISK OF EXPLOSIVE GASES.

a. WORKING IN VICINITY OF A LEAD-ACID BATTERY IS DANGEROUS.

BATTERIES GENERATE EXPLOSIVE GASES DURING NORMAL BATTERY

OPERATION. FOR THIS REASON, IT IS OF UTMOST IMPORTANCE THAT

YOU FOLLOW THE INSTRUCTIONS EACH TIME YOU USE THE CHARGER.

b. To reduce risk of battery explosion, follow these instructions and those published

by battery manufacturer and manufacturer of any equipment you intend to use in

vicinity of battery. Review cautionary markings on these products and on the engine.

• 6 •

2. PERSONAL SAFETY PRECAUTIONS

2.1 Consider having someone close enough by to come to your aid when you work

near a lead-acid battery.

2.2 Have plenty of fresh water and soap nearby in case battery acid contacts skin,

clothing, or eyes.

2.3 Wear complete eye protection and clothing protection. Avoid touching eyes while

working near battery.

2.4 If battery acid contacts skin or clothing, wash immediately with soap and water.

If acid enters eye, immediately ood eye with running cold water for at least 10

minutes and get medical attention immediately.

2.5 NEVER smoke or allow a spark or ame in vicinity of battery or engine.

2.6 Be extra cautious, to reduce risk of dropping a metal tool onto battery. It might spark

or short-circuit battery or other electrical part that may cause explosion.

2.7 Remove personal metal items such as rings, bracelets, necklaces, and watches

when working with a lead-acid battery. A lead-acid battery can produce a short-

circuit current high enough to weld a ring or the like to metal, causing a severe burn.

2.8 Use the charger for charging only 6V and 12V LEAD-ACID (STD, AGM or GEL)

rechargeable batteries.

It is not intended to supply power to a low voltage electrical

system other than in a starter-motor application. Do not use battery charger for

charging dry-cell batteries that are commonly used with home appliances. These

batteries may burst and cause injury to persons and damage to property.

2.9 NEVER charge a frozen battery.

3. PREPARING TO CHARGE

3.1 If necessary to remove battery from vehicle to charge, always remove grounded

terminal from battery rst. Make sure all accessories in the vehicle are off, so as

not to cause an arc.

3.2 Be sure area around battery is well ventilated while battery is being charged.

3.3 Clean battery terminals. Be careful to keep corrosion from coming in contact with eyes.

3.4 Add distilled water in each cell until battery acid reaches level specied by battery

manufacturer. Do not overll. For a battery without removable cell caps, such as valve

regulated lead acid batteries, carefully follow manufacturer’s recharging instructions.

3.5 Study all battery manufacturer’s specic precautions while charging and

recommended rates of charge.

3.6 Determine voltage of battery by referring to car owner’s manual and make

sure that output voltage selector switch is set at correct voltage (if applicable).

If charger has adjustable charge rate, charge battery initially at lowest rate.

• 7 •

4. CHARGER LOCATION

4.1 Locate charger as far away from battery as DC cables permit.

4.2 Never place charger directly above battery being charged; gases from battery will

corrode and damage charger.

4.3 Never allow battery acid to drip on charger when reading electrolyte specic

gravity or lling battery.

4.4 Do not operate charger in a closed-in area or restrict ventilation in any way.

4.5 Do not set a battery on top of charger.

5. DC CONNECTION PRECAUTIONS

5.1 Connect and disconnect DC output clips only after setting any charger switches

to “off” position and removing AC cord from electric outlet. Never allow clips to

touch each other.

5.2 Attach clips to battery and chassis, as indicated in sections 6 and 7.

6. FOLLOW THESE STEPS WHEN BATTERY IS INSTALLED IN VEHICLE

WARNING: A SPARK NEAR THE BATTERY MAY CAUSE A BATTERY

EXPLOSION. TO REDUCE THE RISK OF A SPARK NEAR THE BATTERY:

6.1 Position AC and DC cords to reduce risk of damage by hood, door, or moving

engine part.

6.2 Stay clear of fan blades, belts, pulleys, and other parts that can cause injury to persons.

6.3 Check polarity of battery posts. POSITIVE (POS, P, +) battery post usually has

larger diameter than NEGATIVE (NEG, N,–) post.

6.4 Determine which post of battery is grounded (connected) to the chassis. If negative

post is grounded to chassis (as in most vehicles), see (6.5). If positive post is

grounded to the chassis, see (6.6).

6.5 For negative-grounded vehicle, connect POSITIVE (RED) clip from battery charger

to POSITIVE (POS, P, +) ungrounded post of battery. Connect NEGATIVE (BLACK)

clip to vehicle chassis or engine block away from battery. Do not connect clip to

carburetor, fuel lines, or sheet-metal body parts. Connect to a heavy gauge metal

part of the frame or engine block.

6.6 For positive-grounded vehicle, connect NEGATIVE (BLACK) clip from battery

charger to NEGATIVE (NEG, N, –) ungrounded post of battery. Connect

POSITIVE (RED) clip to vehicle chassis or engine block away from battery. Do

not connect clip to carburetor, fuel lines, or sheet-metal body parts. Connect to a

heavy gauge metal part of the frame or engine block.

6.7 When disconnecting charger, turn switches to off, disconnect AC cord, remove clip

from vehicle chassis, and then remove clip from battery terminal.

6.8 See Operating Instructions for length of charge information.

• 8 •

7. FOLLOW THESE STEPS WHEN BATTERY IS OUTSIDE VEHICLE

WARNING: A SPARK NEAR THE BATTERY MAY CAUSE A BATTERY

EXPLOSION. TO REDUCE THE RISK OF A SPARK NEAR THE BATTERY:

7.1 Check polarity of battery posts. POSITIVE (POS, P, +) battery post usually has a

larger diameter than NEGATIVE (NEG, N, –) post.

7.2 Attach at least a 24-inch-long 6-gauge (AWG) insulated battery cable to

NEGATIVE (NEG, N, –) battery post.

7.3 Connect POSITIVE (RED) charger clip to POSITIVE (POS, P, +) post of battery.

7.4 Position yourself and free end of cable as far away from battery as possible –

then connect NEGATIVE (BLACK) charger clip to free end of cable.

7.5 Do not face battery when making nal connection.

7.6 When disconnecting charger, always do so in reverse sequence of connecting

procedure and break rst connection while as far away from battery as practical.

7.7 A marine (boat) battery must be removed and charged on shore. To charge it on

board requires equipment specially designed for marine use.

8. GROUNDING AND AC POWER CORD CONNECTIONS

8.1 This battery charger is for use on a nominal 120 volt circuit. The plug must be

plugged into an outlet that is properly installed and grounded in accordance with

all local codes and ordinances. The plug pins must t the receptacle (outlet). Do

not use with an ungrounded system.

8.2 DANGER: Never alter the AC cord or plug provided – if it does not t the outlet,

have a proper grounded outlet installed by a qualied electrician. An improper

connection can result in a risk of an electric shock or electrocution.

NOTE: Pursuant to Canadian Regulations, use of an adapter plug is not allowed

in Canada. Use of an adapter plug in the United States is not recommended and

should not be used.

8.3 USING AN EXTENSION CORD

The use of an extension cord is not recommended. If you must use an extension

cord, follow these guidelines:

• Pins on plug of extension cord must be the same number, size, and shape as

those of plug on charger.

• Ensure that the extension cord is properly wired and in good electrical condition.

• Wire size must be large enough for the AC ampere rating of charger, as

specied below:

Length of cord (feet) 25 50 100 150

AWG* size of cord 18 18 18 16

*AWG-American Wire Gauge

• 9 •

9. ASSEMBLY INSTRUCTIONS

9.1 Remove all cord wraps and uncoil the cables prior to using the battery charger.

10. MOUNTING INSTRUCTIONS

Mounting the charger to the fender well:

The charger can be mounted directly to the fender well of

your vehicle, as shown, using the double-sided adhesive

and cable tie (included).

Mounting the charger alongside the battery:

The charger can also be mounted alongside your vehicle’s

battery, using the bracket (sold separately). If possible, mount the charger to the

side of the battery away from the engine and fan blades. Mount the bracket to the

charger as shown using the nuts and bolts provided with the bracket. Loosen the

battery retaining hardware enough that you can insert the bracket between the

bottom of the battery and the battery mounting tray as shown. Position the charger

so that it will not rub against the battery or any other part of the vehicle, and then

tighten the battery retaining hardware. NOTE: Do not drill or

puncture the battery.

Electrical Installation:

The output leads of the charger

are terminated with 3/8˝ dia. ring

lugs. Route and secure the AC

cord and the output wiring away

from the gas line, carburetor or

other hot, sharp, moving or pinch parts to avoid damage to the insulation. Secure

the AC cord using a cable tie or equivalent. If you have difculty connecting the

output leads, consult your local auto supply store, they may assist you in nding a

connecting device for your application.

11. LED INDICATORS

RED LED (solid): The charger is charging the battery.

RED LED (ashing): The connections are reversed, or the battery is bad.

GREEN LED (solid):

The battery is fully charged and the charger is in maintain mode.

NOTE: See Operating Instructions for a complete description of the charger modes.

• 10 •

12. OPERATING INSTRUCTIONS

IMPORTANT: Do not start the vehicle with the charger connected to the AC

outlet, or it may damage the charger and your vehicle.

NOTE: This charger is equipped with an auto-start feature. Current will not be

supplied to the ring terminals until a battery is properly connected. The ring

terminals will not spark if touched together.

CHARGING A BATTERY IN THE VEHICLE

1. Turn off all the vehicle’s accessories.

2. Keep the hood open.

3. Clean the battery terminals.

4. Place the charger on a dry, non-ammable surface.

5. Lay the AC/DC cables away from any fan blades, belts, pulleys and other

moving parts.

6. For a negative-ground vehicle (as in most vehicles), connect the charger’s

POSITIVE (RED) ring terminal to the POSITIVE (POS, P, +) battery post. Next,

connect the charger’s NEGATIVE (BLACK) ring terminal to the vehicle chassis

or engine block, away from the battery.

7. For a positive-ground vehicle, connect the charger’s NEGATIVE (BLACK) ring

terminal to the NEGATIVE (NEG, N, -) battery post. Next, connect the charger’s

POSITIVE (RED) ring terminal to the vehicle chassis or engine block away

from the battery. NEVER connect any ring terminals to the carburetor, fuel lines

or sheet-metal body parts.

8. Connect the charger to a live grounded 120V AC outlet.

9. When charging is complete, disconnect the charger from the AC power, remove

the ring terminal from the vehicle’s chassis, and then remove the ring terminal

from the battery terminal.

CHARGING A BATTERY OUTSIDE OF THE VEHICLE

1. Place battery in a well-ventilated area.

2. Clean the battery terminals.

3. Connect a 24-inch long, 6-gauge (AWG) insulated battery cable to the

NEGATIVE (NEG, N, -) battery post (i.e., jumper cable) (not provided).

4. Connect the POSITIVE (RED) ring terminal to the POSITIVE (POS, P, +)

battery post.

5. Position yourself and the “negative post extension” cable as far away from

the battery as possible, and connect the NEGATIVE (BLACK) ring terminal to

the cable’s free end.

• 11 •

6. Connect the charger to a live grounded 120V AC outlet.

7. When charging is complete, disconnect the charger from the AC power,

disconnect the negative ring terminal, and nally the positive ring terminal.

8. A marine (boat) battery must be removed and charged on shore.

BATTERY CHARGING TIMES

BATTERY SIZE/RATING

CHARGE TIME

(1.5A)

SMALL BATTERIES

Motorcycle, garden tractor, etc.

6-12 Ah 2½-5 h

12-32 Ah 5-13¼ h

CARS AND TRUCKS

200-315 CCA 40-60 RC MAINTAIN ONLY

315-550 CCA 60-85 RC MAINTAIN ONLY

550-1000 CCA 85-190 RC MAINTAIN ONLY

MARINE/DEEP-CYCLE

80 RC MAINTAIN ONLY

140 RC MAINTAIN ONLY

160 RC MAINTAIN ONLY

180 RC MAINTAIN ONLY

Times are based on a 50% discharged battery and may change, depending on

age and condition of battery.

AUTOMATIC CHARGING MODE

When an automatic charge is performed, the charger switches to the maintain

mode automatically after the battery is charged. For a battery with a starting

voltage under 1 volt, use a manual charger to pre-charge the battery for ve

minutes, to get additional voltage into the battery.

BAD BATTERY

If charging cannot be completed normally, the charger’s output is shut off and the

RED LED will ash. Have the battery checked and replace, if necessary.

DESULFATION MODE

If the battery is left discharged for an extended period of time, it could become sulfated

and not accept a normal charge. If the charger detects a sulfated battery, the charger

will switch to a special mode of operation designed for such batteries. If successful,

normal charging will resume after the battery is desulfated. Desulfation could take

8-10 hours. If desulfation fails, the RED LED will ash.

COMPLETION OF CHARGE

Charge completion is indicated by the GREEN LED. When solid, the charger has

switched to the maintain mode of operation.

• 12 •

MAINTAIN MODE (FLOAT MODE MONITORING)

When the GREEN LED is solid, the charger has completed charging and started

maintain mode. In this mode, the charger keeps the battery fully charged by delivering

a small current when necessary. If the charger has to provide its maximum maintain

current for a continuous 12 hour period, it will go into abort mode (see Aborted Charge

section). This is usually caused by a drain on the battery or the battery could be bad.

Make sure there are no loads on the battery. If there are, remove them. If there are

none, have the battery checked or replaced.

MAINTAINING A BATTERY

The 90-300A maintains both 6 and 12 volt batteries, keeping them at full charge.

It is not recommended for industrial applications.

NOTE: The maintain mode technology allows you to safely charge and maintain a

healthy battery for extended periods of time. However, problems with the battery,

electrical problems in the vehicle, improper connections or other unanticipated conditions

could cause excessive current draws. As such, occasionally monitoring your battery and

the charging process is required.

13. MAINTENANCE AND CARE

A minimal amount of care can keep your battery charger working properly for years.

• Clean the clamps each time you are nished charging. Wipe off any battery uid

that may have come in contact with the clamps, to prevent corrosion.

• Occasionally cleaning the case of the charger with a soft cloth will keep the nish

shiny and help prevent corrosion.

• Coil the input and output cords neatly when storing the charger. This will help

prevent accidental damage to the cords and charger.

• Store the charger unplugged from the AC power outlet in an upright position.

• Store inside, in a cool, dry place. Do not store the clamps clipped together, on or

around metal, or clipped to the cables.

• 13 •

14. TROUBLESHOOTING

PROBLEM POSSIBLE CAUSE SOLUTION

Battery ring

terminals do not

spark when touched

together.

The charger is equipped with

an auto-start feature. It will not

supply current to the battery

ring terminals until a battery

is properly connected. The

ring terminals will not spark if

touched together.

No problem; this is a normal

condition.

Both LEDs come on

for 2 seconds, then

turn off.

The charger is plugged into an

AC outlet.

No problem; this is normal.

The charger will

not turn on when

properly connected.

AC outlet is dead.

Poor electrical connection.

Bad battery.

Check for open fuse or

circuit breaker supplying

AC outlet.

Check power cord and

extension cord for loose

tting plug.

Have battery checked.

I cannot select a 6V

or 12V setting.

The charger is equipped with

Auto Voltage Detection, which

automatically detects the voltage

and charges the battery.

No problem; this is normal.

15. BEFORE RETURNING FOR REPAIRS

If these solutions do not eliminate the problem, or for more information

about troubleshooting, contact customer service for assistance:

[email protected]

www.batterychargers.com

or call 1-800-621-5485

For REPAIR OR RETURN, contact Customer Service at 1-800-621-5485. DO NOT

SHIP UNIT until you receive a RETURN MERCHANDISE AUTHORIZATION (RMA)

number from Customer Service at Schumacher Electric Corporation.

• 14 •

16. SPECIFICATIONS

Input Voltage ..................................................................120V AC @ 60Hz, 0.4A

Output Voltage .......................................6V or 12V, with Auto Voltage Detection

Output Current Rating ..........................................................1.5A @ 6V and 12V

17. ACCESSORIES

Mounting bracket (with nuts and bolts) .........................................2299000544Z

18. LIMITED WARRANTY

WARRANTY NOT VALID IN MEXICO.

SCHUMACHER ELECTRIC CORPORATION, 801 BUSINESS CENTER DRIVE,

MOUNT PROSPECT, IL 60056-2179, MAKES THIS LIMITED WARRANTY TO

THE ORIGINAL RETAIL PURCHASER OF THIS PRODUCT. THIS LIMITED

WARRANTY IS NOT TRANSFERABLE OR ASSIGNABLE.

Schumacher Electric Corporation (the “Manufacturer”) warrants this charger for

two (2) years from the date of purchase at retail against defective material or

workmanship that may occur under normal use and care. If your unit is not free

from defective material or workmanship, Manufacturer’s obligation under this

warranty is solely to repair or replace your product with a new or reconditioned unit

at the option of the Manufacturer. It is the obligation of the purchaser to forward the

unit, along with proof of purchase and mailing charges prepaid to the Manufacturer

or its authorized representatives in order for repair or replacement to occur.

Manufacturer does not provide any warranty for any accessories used with this

product that are not manufactured by Schumacher Electric Corporation and

approved for use with this product. This Limited Warranty is void if the product is

misused, subjected to careless handling, repaired, or modied by anyone other

than Manufacturer or if this unit is resold through an unauthorized retailer.

Manufacturer makes no other warranties, including, but not limited to, express,

implied or statutory warranties, including without limitation, any implied warranty

of merchantability or implied warranty of tness for a particular purpose. Further,

Manufacturer shall not be liable for any incidental, special or consequential damage

• 15 •

claims incurred by purchasers, users or others associated with this product, including,

but not limited to, lost prots, revenues, anticipated sales, business opportunities,

goodwill, business interruption and any other injury or damage. Any and all such

warranties, other than the limited warranty included herein, are hereby expressly

disclaimed and excluded. Some states do not allow the exclusion or limitation of

incidental or consequential damages or length of implied warranty, so the above

limitations or exclusions may not apply to you. This warranty gives you specic legal

rights and it is possible you may have other rights which vary from this warranty.

THIS LIMITED WARRANTY IS THE ONLY EXPRESS LIMITED WARRANTY AND

THE MANUFACTURER NEITHER ASSUMES OR AUTHORIZES ANYONE TO

ASSUME OR MAKE ANY OTHER OBLIGATION TOWARDS THE PRODUCT

OTHER THAN THIS WARRANTY.

• 16 •

1. INSTRUCCIONES IMPORTANTES DE SEGURIDAD

GUARDE ESTAS INSTRUCCIONES.

1.1 GUARDE ESTAS INSTRUCCIONES – Este manual contiene instrucciones

operativas y de seguridad de importancia.

1.2 Este cargador no está destinado para ser usado por niños.

1.3 No exponga el cargador a la lluvia o a la nieve.

1.4 El uso de un accesorio no recomendado o suministrado por el fabricante del

cargador de baterías puede provocar riesgo de incendio, descarga eléctrica o

lesiones a personas.

1.5 Para reducir el riesgo de daños al enchufe o cable eléctrico, jale del enchufe en

lugar de jalar del cable al desconectar el cargador.

1.6 No se debe utilizar un alargador a menos que resulte absolutamente necesario.

El uso de un alargador inadecuado puede provocar riesgo de incendio o descarga

eléctrica. En caso de que deba utilizarse un alargador, asegúrese de que:

• Los pasadores en el enchufe del alargador posean el mismo número, tamaño y

forma que aquellos presentes en el enchufe del cargador.

• El alargador se encuentre correctamente conectado y en buenas condiciones

eléctricas

• El tamaño del cable sea lo sucientemente extenso para el amperaje en CA del

cargador como se especica en sección 8.

1.7 No utilice el cargador si el mismo posee un enchufe o cable dañado; substituya el

cable o el enchufe inmediatamente por una persona calicada en el ramo.

1.8 No utilice el cargador si el mismo recibió un golpe fuerte, si se cayó o si sufrió

daños de cualquier otra forma; hágalo revisar por una persona capacitada que

efectúe reparaciones.

1.9 No desarme el cargador; hágalo revisar por una persona capacitada que efectúe

reparaciones cuando necesite servicio de mantenimiento o una reparación.

Volver a ensamblar el cargador en forma incorrecta puede provocar riesgo de

incendio o descarga eléctrica.

1.10 Para reducir el riesgo de descarga eléctrica, desenchufe el cargador del

tomacorriente antes de intentar llevar a cabo cualquier actividad de mantenimiento

o limpieza. El simple apagado de los controles no reducirá este riesgo.

• 17 •

1.11 ADVERTENCIA: RIESGO DE GASES EXPLOSIVOS.

a. RESULTA PELIGROSO TRABAJAR EN FORMA CERCANA A UNA BATERÍA

DE PLOMO. LAS BATERÍAS GENERAN GASES EXPLOSIVOS DURANTE

SU NORMAL FUNCIONAMIENTO. POR ESTE MOTIVO, RESULTA DE SUMA

IMPORTANCIA QUE SIGA LAS INSTRUCCIONES CADA VEZ QUE UTILIZA

EL CARGADOR.

b. Para reducir el riesgo de explosión de una batería, siga estas instrucciones

y aquellas publicadas por el fabricante de la batería y por el fabricante de

cualquier equipo que intente utilizar en la proximidad de la batería. Revise las

pautas de precaución en estos productos y en el motor.

2. PRECAUCIONES DE SEGURIDAD PERSONAL

2.1 Considere la idea de que alguna persona se encuentre cerca suyo para poder

ayudarlo cuando trabaje en forma cercana a una batería de plomo-ácido.

2.2 Cuente con una gran cantidad de agua potable y jabón a mano en caso de que el

ácido de la batería tenga contacto con su piel, ropa u ojos.

2.3 Utilice protección visual y corporal completa, incluyendo gafas de seguridad y prendas

de protección. Evite tocar sus ojos mientras trabaje en forma cercana a la batería.

2.4 Si el ácido de la batería tiene contacto con su piel o su ropa, lave de inmediato

el área afectada con agua y jabón. En caso de que ingrese ácido en un ojo,

sumerja el mismo de inmediato bajo agua potable corriente por al menos 10

minutos y obtenga atención médica en forma inmediata.

2.5 NUNCA fume o permita la presencia de chispas o llamas en la proximidad de una

batería o motor.

2.6 Tenga especial cuidado para reducir el riesgo de dejar caer una herramienta

de metal sobre la batería. Esto podría provocar chispas o un cortocircuito en la

batería o en cualquier otra pieza eléctrica que podría provocar una explosión.

2.7 No utilice elementos personales de metal tales como anillos, pulseras, collares y relojes

al trabajar con una batería de plomo-ácido. Una batería de plomo-ácido puede producir

una corriente de cortocircuito lo sucientemente elevada como para soldar un anillo o

provocar efectos similares sobre el metal, causando una quemadura de gravedad.

2.8 Utilice este cargador solamente para cargar baterías de 6V y 12V de tipo plomo-

ácido (estándar, AGM o GEL). Este cargador no está destinado a suministrar

energía a sistemas eléctricos de baja tensión más que en una aplicación de un

motor de arranque. No utilice este cargador de batería para cargar baterías de

pila seca que por lo general se utilizan con artefactos domésticos. Estas baterías

podrían explotar y provocar lesiones a personas o daño a la propiedad.

2.9 NUNCA cargue una batería congelada.

• 18 •

3. PREPARACIÓN PARA LA CARGA

3.1 Si resulta necesario extraer la batería del vehículo para cargarla, siempre retire el

terminal con descarga a tierra en primer lugar. Asegúrese de que todos los accesorios

en el vehículo se encuentren apagados para evitar la formación de arcos eléctricos.

3.2 Asegúrese de que el área que rodea a la batería se encuentre bien ventilada

mientras se carga la batería.

3.3 Limpie los terminales de la batería antes de cargar la batería. Durante la limpieza,

evite que la corrosión producida por aire tenga contacto con sus ojos.

3.4 Agregue agua destilada a cada pila hasta que el ácido de la batería alcance el

nivel especicado por el fabricante de la batería. No provoque derrames. En lo que

concierne a baterías que no cuentan con tapas extraíbles para pilas, tales como

baterías de plomo-ácido reguladas por válvulas (VRLA, por sus siglas en inglés),

siga cuidadosamente las instrucciones de recarga del fabricante.

3.5 Controle todas las precauciones especícas establecidas por el fabricante de la

batería al realizar la carga, así también como los índices de carga recomendados.

3.6 Determine la tensión de la batería al consultar el manual del usuario del vehículo y

asegúrese de que el interruptor de selección de la tensión de salida se encuentre

establecido en la tensión correcta (si es aplicable). Si el cargador posee un índice

de carga ajustable, cargue la batería en el menor índice en primer lugar.

4. UBICACIÓN DEL CARGADOR

4.1 Ubique el cargador a la mayor distancia posible de la batería como lo permitan

los cables de CC.

4.2 Nunca ubique el cargador directamente por encima de la batería que se carga;

los gases de la batería corroerán y dañarán el cargador.

4.3 Nunca permita que el ácido de la batería gotee sobre el cargador al leer el peso

especíco del electrolito o al cargar la batería.

4.4 No utilice el cargador en un área cerrada o restrinja la ventilación en cualquier forma.

4.5 No ubique la batería encima del cargador.

5. PRECAUCIONES DE CONEXIÓN EN CC

5.1 Conecte y desconecte las pinzas de salida CC. sólo después de haber establecido

todos los interruptores del cargador a la posición de “apagado” (si es aplicable) y de

haber desconectado el enchufe de C.A. del tomacorriente eléctrico. Nunca permita

que las pinzas tengan contacto entre sí.

5.2 Sujete las pinzas a la batería y al chasis, como se indica en en las secciones 6 y 7.

• 19 •

6. SIGA ESTOS PASOS CUANDO LA BATERÍA ESTÉ COLOCADA EN EL VEHÍCULO

ADVERTENCIA: UNA CHISPA PROVOCADA CERCA DE LA BATERÍA PUEDE

CAUSAR LA EXPLOSIÓN DE LA BATERÍA. PARA REDUCIR EL RIESGO DE

PROVOCAR CHISPAS CERCA DE LA BATERÍA:

6.1 Ubique los cables de CA y CC adecuadamente para reducir el riesgo de daños

por la cubierta, la puerta y las piezas móviles o calientes del motor.

6.2 Manténgase alejado de las paletas del ventilador, correas, poleas y otras piezas

que podrían provocar lesiones.

6.3 Verique la polaridad de los bornes de la batería. El borne POSITIVO (POS, P, +) de

la batería generalmente posee un diámetro mayor al borne NEGATIVO (NEG, N, -).

6.4 Determine qué borne de la batería hace descarga a tierra (se encuentra

conectado) con el chasis. Si el borne negativo hace descarga a tierra con el

chasis (como en la mayor parte de los vehículos), ver el paso (6.5) Si el borne

positivo hace descarga a tierra con el chasis, ver el paso (6.6).

6.5 En un vehículo con descarga a tierra por borne negativo, conecte el gancho

POSITIVO (ROJO) del cargador de batería al borne POSITIVO (POS, P, +) sin

descarga a tierra de la batería. Conecte el gancho NEGATIVO (NEGRO) al

chasis del vehículo o al bloque motor alejado de la batería. No conecte el gancho

al carburador, líneas de combustible o cuerpos metálicos. Conecte a una pieza

metálica de calibre grueso del marco o del bloque motor.

6.6 En un vehículo con descarga a tierra por borne positivo, conecte el gancho

NEGATIVO (NEGRO) del cargador de batería al borne NEGATIVO (NEG, N, -) sin

descarga a tierra de la batería. Conecte el gancho POSITIVO (ROJO) al chasis del

vehículo o al bloque motor alejado de la batería. No conecte al carburador, líneas

de combustible o cuerpos metálicos. Conecte a una pieza metálica de calibre

grueso del marco o del bloque motor.

6.7 Al desconectar el cargador, apague todos los interruptores (en su caso),

desconecte el cable de C.A., retire el gancho del chasis del vehículo y luego

retire el gancho del terminal perteneciente a la batería.

6.8 Vea Instrucciones de Operación para duración de la carga.

• 20 •

7. SIGA ESTOS PASOS CUANDO LA BATERÍA SE ENCUENTRE FUERA DEL VEHÍCULO

ADVERTENCIA: UNA CHISPA PROVOCADA CERCA DE LA BATERÍA PUEDE

CAUSAR LA EXPLOSIÓN DE LA BATERÍA. PARA REDUCIR EL RIESGO DE

PROVOCAR CHISPAS CERCA DE LA BATERÍA:

7.1 Verique la polaridad de los bornes de la batería. El borne POSITIVO (POS, P, +) de

la batería generalmente posee un diámetro mayor al borne NEGATIVO (NEG, N, -).

7.2 Sujete al menos un cable aislado de batería de 24 pulgadas (61 cm) de largo con

calibre 6 según el Calibre americano de cables (AWG, por sus siglas en inglés) al

borne NEGATIVO (NEG, N, -) de la batería.

7.3 Conecte el gancho POSITIVO (ROJO) del cargador al borne POSITIVO (POS, P, +)

de la batería.

7.4 Ubíquese junto con el extremo libre del cable que previamente sujetó al borne

NEGATIVO (NEG, N, -) de la batería a la mayor distancia posible de la batería. Luego

conecte el gancho NEGATIVO (NEGRO) del cargador al extremo libre del cable.

7.5 No se ubique en posición frontal a la batería al realizar la conexión nal.

7.6 Al desconectar el cargador, siempre hágalo en forma inversa al procedimiento de

conexión y realice la primera conexión tan lejos de la batería como sea posible.

7.7 Una batería marina (para barcos) se debe retirar y cargar en tierra. Para realizar una

carga a bordo se necesitan equipamientos especialmente diseñados para uso marino.

8. CONEXIONES A TIERRA Y ENERGÍA DE CA

8.1 Este cargador de batería está destinado a un uso en un circuito con tensión

nominal de 120 V. El enchufe se debe conectar a un tomacorriente adecuadamente

instalado y que cuente con descarga a tierra de acuerdo con todas las

ordenanzas y códigos. Los pasadores del enchufe deben adaptarse al receptáculo

(tomacorriente). No utilizar con un sistema que no posea descarga a tierra.

8.2 PELIGRO: Nunca altere el cable o enchufe de C.A. suministrado, si no se ajusta

al tomacorriente, haga instalar un tomacorriente adecuado con descarga a

tierra por medio de un electricista capacitado. Una conexión inadecuada puede

provocar un riesgo de descarga eléctrica o electrocución.

NOTA: De acuerdo a las Leyes Canadienses, el uso de un enchufe adaptador

no es permitido en el Canada. El uso de un enchufe como adaptador no se

recomienda y no debe ser utilizado Estados Unidos.

La page charge ...

Schumacher NAPA 90-300A Automatic Battery Charger/Maintainer Le manuel du propriétaire

Marque: Schumacher

Modèle: NAPA 90-300A Automatic Battery Charger/Maintainer

Catégorie: Chargeurs de batterie

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

Schumacher NAPA 90-300A Automatic Battery Charger/Maintainer Le manuel du propriétaire

Schumacher NAPA 90-300A Automatic Battery Charger/Maintainer Le manuel du propriétaire

dans d''autres langues

Documents connexes