Yamaha CDC-835 Le manuel du propriétaire

Catégorie
Lecteur CD
Taper
Le manuel du propriétaire
IMPORTANT!
Please record the serial number of this
unit in the space below.
Model:
Serial No.:
The serial number is located on the rear
of the unit.
Retain this Owner’s Manual in a safe
place for future reference.
WARNING
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE
THIS UNIT TO RAIN OR MOISTURE.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK), NO USER-SERVICEABLE
PARTS INSIDE, REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead
symbol, within an equilateral triangle,
is intended to alert you to the
presence of uninsulated “dangerous
voltage” within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an
equilateral triangle is intended to alert
you to the presence of important
operating and maintenance
(servicing) instructions in the
literature accompanying the
appliance.
Explanation of Graphical Symbols
CAUTION
Natural Sound Compact Disc Player
5-Disc Carousel Auto-changer
PLAYXCHANGE; Disc changing capability while playing another
Random Access Programmable Play
Random-Sequence Play
Single Track/Entire Disc/All Disc Repeat Play
Program Data Filing Capability
5-Mode Digital Equalizer
10-Disc Relay Play by Connecting Two CDC-835s
Display Brightness Changing Capability
Concealed Control Panel
Remote Control Capability
CDC-835
Thank you for selecting this YAMAHA compact disc player.
OWNER’S MANUAL
CONTENTS
Safety Instructions................................... 2
Connections ............................................ 4
Identification of Components................... 5
Loading the Disc/Disc Play...................... 6
Random-Sequence Play ....................... 11
Program Play......................................... 12
Repeat Play........................................... 16
Index Search ......................................... 16
Track Programming for
Recording to Tape............................... 17
Relay Play ............................................. 20
Notes about the Remote Control
Transmitter
........................................... 22
Notes about Handling Compact Discs... 22
Troubleshooting..................................... 23
Specifications ........................................ 23
S
2
SAFETY INSTRUCTIONS
1 Read Instructions – All the safety and operating
instructions should be read before the unit is operated.
2 Retain Instructions – The safety and operating
instructions should be retained for future reference.
3 Heed Warnings – All warnings on the unit and in the
operating instructions should be adhered to.
4 Follow Instructions – All operating and other instructions
should be followed.
5 Water and Moisture – The unit should not be used near
water – for example, near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a swimming
pool, etc.
6 Carts and Stands – The unit should be used only with a
cart or stand that is recommended by the manufacturer.
6A A unit and cart combination should be
moved with care. Quick stops,
excessive force, and uneven surfaces
may cause the unit and cart combination
to overturn.
7 Wall or Ceiling Mounting – The unit should be mounted to
a wall or ceiling only as recommended by the
manufacturer.
8 Ventilation – The unit should be situated so that its
location or position does not interfere with its proper
ventilation. For example, the unit should not be situated
on a bed, sofa, rug, or similar surface, that may block the
ventilation openings; or placed in a built-in installation,
such as a bookcase or cabinet that may impede the flow
of air through the ventilation openings.
9 Heat – The unit should be situated away from heat
sources such as radiators, stoves, or other appliances
that produce heat.
10 Power Sources – The unit should be connected to a
power supply only of the type described in the operating
instructions or as marked on the unit.
11 Power-Cord Protection – Power-supply cords should be
routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying
particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the unit.
12 Cleaning – The unit should be cleaned only as
recommended by the manufacturer.
13 Nonuse Periods – The power cord of the unit should be
unplugged from the outlet when left unused for a long
period of time.
14 Object and Liquid Entry – Care should be taken so that
objects do not fall into and liquids are not spilled into the
inside of the unit.
15 Damage Requiring Service – The unit should be serviced
by qualified service personnel when:
A. The power-supply cord or the plug has been
damaged; or
B. Objects have fallen, or liquid has been spilled into the
unit; or
C. The unit has been exposed to rain; or
D. The unit does not appear to operate normally or
exhibits a marked change in performance; or
E. The unit has been dropped, or the cabinet damaged.
16 Servicing – The user should not attempt to service the
unit beyond those means described in the operating
instructions. All other servicing should be referred to
qualified service personnel.
17 Power Lines – An outdoor antenna should be located
away from power lines.
18 Grounding or Polarization – Precautions should be taken
so that the grounding or polarization is not defeated.
1 To ensure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
2 Install your unit in a cool, dry, clean place – away from
windows, heat sources, and too much vibration, dust,
moisture or cold. Avoid sources of hum (transformers,
motors). To prevent fire or electrical shock, do not
expose to rain and water.
3 Do not operate the unit upside-down. It may overheat,
possibly causing damage.
4 Never open the cabinet. If a foreign object drops into the
set, contact your dealer.
5 Do not use force on switches, knobs or cords. When
moving the set, first turn the unit off. Then gently
disconnect the power plug and the cords connecting to
other equipment. Never pull the cord itself.
6 Do not attempt to clean the unit with chemical solvents;
this might damage the finish. Use a clean, dry cloth.
7 Be sure to read the “TROUBLESHOOTING” section on
common operating errors before concluding that your unit
is faulty.
CAUTION FOR CARRYING THIS UNIT
Be sure not to carry or tip the unit with discs remaining in it.
CAUTION FOR MOVING THIS UNIT
When moving this unit, first remove all discs from the disc
tray and close the tray by pressing the OPEN/CLOSE
button, and then switch off the power after you confirm that
the display has turned as follows.
Never switch off the power if the display does not turn as
above, otherwise the unit will get out of order during
moving because the internal mechanism is not locked.
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT
3
As the laser beam used in this compact disc player is harmful
to the eyes, do not attempt to disassemble the cabinet. Refer
servicing to qualified personel only.
To avoid electrical shock, do not open the unit. Refer
servicing to qualified personnel only.
DANGER: The use of optical instrument with this product will
increase eye hazard.
CAUTION
Use of controls or adjustments or performance of
procedures other than those specified herein may result in
hazardous radiation exposure.
DANGER
Invisible laser radiation when open and interlock failed or
defeated.
Avoid direct exposure to beam.
The apparatus is not disconnected from the AC power
source as long as it is connected to the wall outlet, even if
the apparatus itself is turned off.
YAMAHA and the Electronic Industries Association’s
Consumer Electronics Group want you to get the most out of
your equipment by playing it at a safe level. One that lets the
sound come through loud and clear without annoying blaring or
distortion – and, most importantly, without affecting your
sensitive hearing. Since hearing damage from
loud sounds is often undetectable until it is too
late, YAMAHA and the Electronic Industries
Association’s Consumer Electronics Group
recommend you to avoid prolonged exposure
from excessive volume levels.
We Want You Listening For A Lifetime
FCC INFORMATION
1. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC,
to use the product.
2. IMPORTANT : When connecting this product to
accessories and/or another product use only high
quality shielded cables. Cable/s supplied with this
product MUST be used. Follow all installation
instructions. Failure to follow instructions could void
your FCC authorization to use this product in the USA.
WARNING
3. NOTE : This product has been tested and found to
comply with the requirements listed in FCC Regulations,
Part 15 for Class “B” digital devices. Compliance with
these requirements provides a reasonable level of
assurance that your use of this product in a residential
environment will not result in harmful interference with
other electronic devices.
This equipment generates/uses radio frequencies and,
if not installed and used according to the instructions
found in the users manual, may cause interference
harmful to the operation of other electronic devices.
Compliance with FCC regulations does not guarantee
that interference will not occur in all installations. If this
product is found to be the source of interference, which
can be determined by turning the unit “OFF” and “ON”,
please try to eliminate the problem by using one of the
following measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient
the antenna. If the antenna lead-in is 300 ohm ribbon lead,
change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA
90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
CONNECTIONS
Before making any connections, switch OFF the power to
the unit and the amplifier or other component.
Connections should be made to the correct input terminals
of the amplifier or other component.
If the placement of this unit causes noise to other
equipment, such as a tuner, separate them from each other.
If you use the DIGITAL OUTPUT (COAXIAL) terminal for the
connection, be sure to set the DIGITAL OUT ON/OFF switch
on the rear of this unit to the “ON” position. Otherwise, this
switch should be set to the “OFF” position.
4
To AC outlet
COAXIAL
DIGITAL OUT
ON
OFF
2nd CHANGER
INPUT
MAIN
2nd
CONTROL
L
R
LINE OUT
RELAY PLAY
COAXIAL
DIGITAL IN
CD
L
R
To AC outlet
This unit
Amplifier
Connection cord
When the LINE OUT (analog) terminals of this
unit are used (
)
Be sure to set the DIGITAL OUT ON/OFF switch on the rear
of this unit to the “OFF” position.
Be sure that the left (“L”) and right (“R”) LINE OUT terminals
are connected to the corresponding (left and right) terminals
of the amplifier or other component.
Connect the “LINE OUT” terminals to the “CD” (or “AUX”)
terminals of the amplifier. If the amplifier does not have
such terminals, use the “TAPE PB” terminals. For additional
details concerning these connections, refer to the operation
instructions for the amplifier being used.
Adjust the level of signals output into an amplifier, etc. by
using the OUTPUT LEVEL control.
* Switching the DIGITAL OUT ON/OFF switch on the rear
panel resets the adjusted LINE OUT (analog) output level
to maximum.
When the DIGITAL OUT (COAXIAL) terminal of
this unit is used (
)
Be sure to set the DIGITAL OUT ON/OFF switch on the rear
of this unit to the “ON” position.
Make the connection from this terminal to the digital input
terminal of an amplifier or D/A (digital-to-analog) converter
by using a connection cord.
The level of signals output into an amplifier is fixed to max.
and cannot be adjusted.
Choose one of the ways listed below to connect this unit to your amplifier.
Connection cord
(included)
IDENTIFICATION OF COMPONENTS
FRONT PANEL
REMOTE CONTROL TRANSMITTER
The control functions on the main unit and on the remote
control transmitter are virtually identical, with the exceptions
described below.
* The PLAY/PAUSE button on the main unit has both
the functions of the PLAY button and the PAUSE
button on the remote control transmitter.
* The DEQ (DIGITAL EQUALIZER) button on the
main unit is divided into five buttons with individual
functions on the remote control transmitter.
(Refer to page 8.)
5
PLAY
OPEN/
CLOSE
DEQ
DISPLAY
CLASSIC
VOCAL
JAZZ
ROCK
TIME
PROG
TAPE
CLEAR
FLAT
FILE
DIMMER
12
3 +10
456
789
0
D-MODE
S/F REP
RANDOM
DISC1
INDEX
DISC SKIP
PAUSE
STOP
DOWN
UP
OUTPUT LEVEL
DISC2
DISC3 DISC4
DISC5
DISC1 DISC2
DISC3
DISC4
DISC5
SKIP
SEARCH
REMOTE
CONTROL
TRANSMITTER
select button
TIME
display mode-
Display panel
Remote control sensor
POWER
switch
Disc tray
OPEN/CLOSE
button
button
DISC SKIP
STOP
button
button
button
PLAYXCHANGE
PLAY/PAUSE
DISC
-select buttons
RANDOM button
PHONES
jack
REPEAT
button
-select button
LEVEL
control
PROG
button
SEARCH
button
SKIP
button
OUTPUT
Disc play
MODE
POWER
FILE
SAVE
AUTO
DISPLAY OFF
TIME
1234 5
SKIP
SEARCH
+101234567890
PROG TAPE
PLAYXCHANGE
OPEN/CLOSE
PLAY/
PAUSE
STOP
DISC SKIP
FILE
MODE
REPEAT
RANDOM
OUTPUT LEVEL
DOWN UP
PHONES
CLEAR
DEQ
CLASSIC
VOCAL
JAZZ
ROCK
DISC
DEQ (DIGITAL EQUALIZER) button
Numeric buttons
TAPEbutton
FILEbutton
CLEARbutton
D-MODE button
(identical with the
disc play MODE-
select button on
the main unit.)
DISC-select buttons
for the 2nd CD player
used in relay play.
(Refer to page 20.)
DIMMER button
S/F REP button
(identical with the
REPEAT button
on the main unit.)
INDEX button
LOADING THE DISC/DISC PLAY
1
2
3
4
5
Select the disc play mode (DISC MODE: SINGLE or
ALL) while watching the display.
“SINGLE” mode: The unit will play a designated disc only.
“ALL” mode: The unit will play all discs in the tray in
sequence.
6
* If necessary, select a desired disc by using a DISC-select
button or the DISC SKIP button.
Notes
After closing the disc tray by pressing the OPEN/CLOSE
button in the stop mode or after selecting any disc by using
the DISC SKIP button, the display shows the total number of
tracks and the total recorded time of the disc to be played for
a few seconds.
Additionally, you can close the disc tray by pressing the
PLAY/PAUSE button, a DISC-select button, a numeric
button or the RANDOM button, or by pressing the front edge
of the disc tray gently. If the tray is closed in these ways,
play will begin automatically, however, the display will not
show the total number of tracks and the total recorded time
of the first disc to be played.
PLAYXCHANGE
During play, you can open the disc tray by pressing the
PLAYXCHANGE button without interrupting disc play.
However, in this case, pressing the DISC SKIP button has no
effect.
6
Shows the selected disc
mode.
Label side
upward
Disc tray
1234 5
DISC
5
6
2,4
3,6
6
1
To stop play temporarily
* To resume play, press the PLAY/PAUSE button again
(or press the PLAY or PAUSE button on the remote control
transmitter).
To stop play completely
DIRECT PLAY
Select a desired track by using the numeric buttons.
Example: To select track 25
Press
twice, then immediately press
once.
* If a track number higher than the highest track number on the
disc is selected, the last track on the disc will be played.
SKIP PLAY
To play from the beginning of the track following the one
now playing
To play from the beginning of the track now playing
To play from the beginning of the track before the one now
playing
(twice)
* These operations can also be performed when the unit is in
the pause or stop mode.
Display information at disc play
Encloses the tray number of the disc standing by to be
played or the disc now playing.
Shows the tray numbers with discs.
Shows the track number to be played.
Shows the time displays. (Refer to “Selecting time
displays” on page 9.)
Displays the numbers that correspond to the numbers of
the tracks (as high as number 20) on the disc. After each
track is played, its corresponding number disappears so the
number of remaining tracks (and their numbers) can be
seen at a glance.
7
To play a desired track on the disc
or
1
10
2
34 5 6 78
90
+
➀➁
The selected track
number is displayed.
1
10
2
34 5 6 78
90
+
Using the built-in DIGITAL EQUALIZER (DEQ)
If desired, select any DEQ-mode suitable for the source sound.
CLASSIC More expanded sound is gained.
It is suitable for listening to classic music, etc.
VOCAL Vocal part of the source sound is emphasized.
JAZZ You can enjoy acoustic image of the source
sound with much presence.
ROCK Low range and high range of the source sound
are somewhat emphasized.
It is suitable for listening to rock or pop music.
FLAT The source sound is played back without any
DIGITAL EQUALIZER effect.
8
To advance or reverse play rapidly (MANUAL SEARCH)
To advance rapidly
To reverse rapidly
The sound can be heard (although slightly garbled) during
manual search in either direction. This is convenient for
locating a precise position within a track, or for reviewing the
contents quickly.
Manual search can also be performed while disc play is
paused, though no sound will be heard.
(press and hold)
(press and hold)
On the front panel
Pressing the DEQ button will switch the mode in turn.
The indicator for the selected mode will illuminate.
[No illumination shows that the DIGITAL EQUALIZER is turned
off (FLAT).]
On the remote control transmitter
Press any desired DEQ-mode select button.
DEQ
CLASSIC
VOCAL
JAZZ
ROCK
DEQ
CLASSIC
VOCAL
JAZZ
ROCK
FLAT
Note
The remaining time
will not be displayed for track number
21 or higher.
9
Selecting time displays
You can select any of the four time displays by pressing the TIME display mode-select button.
Elapsed time of the track now playing
Remaining time of the track now playing
Total disc play time
Total remaining time on the disc
Changing brightness of the display
You can change the brightness of the display (or turn off the illumination) by pressing the DIMMER button.
During play
Normal illumination
Dim
“OFF”
* While the display illumination is off,
the AUTO DISPLAY OFF indicator
on the front panel illuminates.
Except during play
Normal illumination
Dim
Dim
(The AUTO DISPLAY OFF indicator illuminates.
In this mode, if a disc is played, the display
illumination will be off.)
10
When you listen with headphones
Connect the headphones to the PHONES jack and adjust the
volume by using the OUTPUT LEVEL control.
* Note that the use of the OUTPUT LEVEL control will also
vary the level of the signal output to the amplifier.
* If the DIGITAL OUT (COAXIAL) terminal on the rear of this
unit is used for the connection to the amplifier, the PHONES
jack cannot be used.
Open/close the control door
When it is not necessary to operate controls inside the control
door, close the door.
To close the door To open the door
PHONES
OUTPUT LEVEL
DOWN UP
or
1
2
3 Select whether to play one disc or all discs in the tray.
* If the “SINGLE” disc play mode is selected, next select a
desired disc by using the DISC SKIP button or a DISC-
select button.
4
To cancel random-sequence play
Press the STOP button or RANDOM button once again, or
open the disc tray by pressing the OPEN/CLOSE button.
Notes
This feature will not function during programming, or during
programmed play.
If the POWER is switched off when the random-sequence
play mode is functioning, when the POWER is switched on
again, the unit will begin the random-sequence play
automatically. (This feature is available for timer play.)
If the SKIP button is pressed during random-sequence
play, the next randomly programmed track will be played. If
the SKIP button is pressed, play will return to the
beginning of the track now being played.
This indication appears while the unit is
mixing up tracks.
Total remaining time on the disc will not be displayed during
random-sequence play.
11
3
42
RANDOM-SEQUENCE PLAY
You can play the tracks in a random sequence (up to 99 tracks). The unit will automatically mix up tracks from all discs or any
desired disc in the disc tray.
Shows the program number for the track to be set next.
Shows the selected disc and track number.
Shows the total time of the tracks currently programmed.
Shows only the numbers of programmed tracks on the
selected disc.
* If “P-01” does not appear in the display after the PROG
button is pressed, press the TIME display mode-select
button.
* If the total time exceeds 99 minutes and 59 seconds, the
time will not be displayed.
12
➁➂
1
Stop the unit.
4
If necessary, select any desired DEQ-mode.
2
3
If necessary, select the desired disc.
5
Select the desired track.
6
When the programming is completed;
* Repeat step 3 – 5 to set more programs.
Display information during programming
or
1234 5
DISC
DEQ
CLASSIC
VOCAL
JAZZ
ROCK
1
10
2
34 5 6 78
90
+
2
3 6
1
3
4
5
PROGRAM PLAY
You can enjoy listening to your favorite tracks selected from one or several discs in any desired order using programmed play.
* In addition, the DEQ (DIGITAL EQUALIZER)-mode selected for each track selection can be also programmed.
Notes
You can set as many as 40 programs at one time.
You can set a whole disc as a program by pressing “0”,
instead of selecting a track number. At that time, “AL”
flashes in the display.
If you will make programming with the DISC 1 tray empty, be
sure to press the DISC SKIP button before starting
programming.
If you will program tracks from more than one disc, before
you press the PROG button, check the total recorded time of
each disc on the disc tray by pressing the DISC SKIP button
in turn. Without this operation, the total time of the
programmed tracks will not be displayed during
programming.
The total time of the programmed tracks will not be
displayed, if a track number higher than 20 is programmed.
If, during programming, the TIME display mode-select button
is pressed, the program number display can be changed to
display the total time of the programmed tracks or no
information. To return to the previous display, press the
TIME display mode-select button once again.
The SKIP ( and ) button can be used during
playing, but only within the range of the programmed tracks.
The SEARCH ( and ) button can be used during
playing to search through all tracks, including
unprogrammed tracks.
To stop program play
Press the STOP button. The first track number programmed
will be displayed.
To resume play, press the PLAY/PAUSE button. Play will
begin from the beginning of the program.
To cancel a programmed setting
There are several methods, as described below.
Press the CLEAR button while the unit is stopped.
Press the STOP button while the unit is stopped.
Open the disc tray.
Switch off the power.
To check programmed data
1. If the unit is in the play mode, press the STOP button.
2. Press the PROG button.
3. Each time the SKIP button is pressed, the track
numbers and sequential order of the programmed tracks
can be checked one after another. The display of the track
number can be returned (sequentially in reverse order) by
pressing the SKIP button.
To correct programmed data
1. Follow the procedure described in “To check programmed
data”.
2. Display the track number to be corrected by pressing the
SKIP button.
3. Press a numeric button to select a track to replace the one
displayed. The previously programmed track will be
cleared from the memory and the new one will be
programmed.
4. After the correction has been completed, press the PROG
button or PLAY/PAUSE button once again.
13
14
To file data of tracks programmed in a desired
order
1. Follow step 1, 2, 3 and 4 on page 12.
(In step 4, turn the DEQ off (FLAT).)
2. Select track numbers in a desired order (by pressing
numeric buttons).
3. Press the FILE button.
* If programs have already been set, make sure that
“TRACK” is flashing continuously in the display. If it is not,
once again press the PROG button. (If a program play is
being performed, press the STOP button, and then press
the PROG button.) Next, after setting the DEQ off (FLAT),
press the FILE button.
Filing of a DEQ (DIGITAL EQUALIZER)-mode
unique for a disc
Only one type of the DEQ-mode can be filed for any one disc.
By this function, you can play a disc with the filed DEQ-mode
at any time without re-setting it.
To file data of tracks programmed in a desired
order with DEQ-mode
1. Follow step 1, 2, 3 and 4 on page 12.
2. Select track numbers in a desired order (by pressing
numeric buttons).
3. Press the FILE button.
To file DEQ-mode for a disc (without track
programming)
1. If the unit is playing a disc, press the STOP button.
2. If the unit is in a program play mode, press the STOP
button or the CLEAR button to cancel it.
3. Select the desired disc by pressing the SKIP button.
4. Select a desired DEQ-mode. (The indicator for the mode
will flash on and off for about 3 seconds. However, if the
DEQ is turned off (FLAT), all indicators will flash.)
5. Press the FILE button while the indicator is flashing.
(If the indicator stops flashing before you press the FILE
button, follow step 4 again.)
* If this procedure is done to a disc for which program data
has already been filed, the data of DEQ-mode will be
replaced with the new one, however, the data of track
programming will not be cleared.
Notes
Program data filed in this way can be retained for about two
weeks with the power switched off.
One-program data can be filed for any one disc. If different
program data is filed for a disc, the previous program data
will be deleted from the file, and only the new program data
will be retained in the file.
Program data for a total of as many as about 100 discs can
be filed at any one time.
FILE
SAVE
AUTO
DISPLAY OFF
FILE
FILE
CLEAR
0
PLAY/PAUSE
OPEN/CLOSE
STOP
DISC
DEQ
(DIGITAL EQUALIZER)
Numeric buttons
PROG
POWER
PROGRAM FILING
This unit has a function that can store (file) program data that has been set. You can play a disc with your favorite program at any
time without setting it again. However, note that you can not file program data which consists of tracks selected from more than one
disc.
To play with program data
1
2
3 If the FILE indicator is not illuminated in the display,
press the FILE button.
4 Select the disc to be played.
Notes
If, in step 4, the SAVE indicator does not illuminate, the disc
does not have its program data in the memory’s file.
To stop the play of the filed program data and change to
ordinary play of the disc, press the FILE button. By this
operation, the disc will be played in the ordinary sequence of
tracks, but the program data in the memory’s file for that disc
will not be deleted from the memory. To once again call out
the program data, follow step 3 and 4.
In the “ALL” disc play mode, discs which have program data
in the memory’s file are played with their program data, and
others are played normally.
To delete program data from file
1 If the unit is playing a disc, press the STOP button.
* If a program play is on standby, press the STOP
button or the CLEAR button tocancel that
program setting.
2
If the FILE indicator is illuminated in the display, press
the FILE button to turn the indicator off.
3 Select the disc of which program you want to delete.
4
5
To delete all program data from the memory’s
file
1 Turn the POWER off.
2
3
4
15
FILE
SAVE
AUTO
DISPLAY OFF
1234 5
DISC
FILE
FILE
PROG
POWER
FILE
0
FILE
0
(Release.)
The SAVE indicator
goes off.
(Press and hold.)
1 Select a track which has index numbers.
2
3 Select the desired index number.
To cancel the index search function
Press the INDEX button.
Notes
Not all discs have index numbers. The index system is a
method for sub-dividing tracks into smaller divisions (such
as, for example, the movements within classical
symphonies) for easier location of those parts. The liner
notes with the disc usually tell if such index numbers are
included.
If an index number is selected that is higher than any index
number on that disc, play will start from the last index
number point on the disc.
For some discs, play may begin slightly prior to the actual
designated index point.
If the disc has no encoded index points, play will begin from
the start of the selected track.
The index number can be designated only while the INDEX
number display is illuminated.
16
SINGLE REPEAT (S REP)
A single track is repeatedly played.
* This is also available in the programmed-play mode and the
random-sequence play mode. (If the repeat play mode is
switched off, the programmed-play mode or the random-
sequence play mode will be resumed.)
FULL REPEAT (F REP)
In the “SINGLE” disc play mode: A designated disc is
repeatedly played.
In the “ALL” disc play mode: All discs in the disc tray are
repeatedly played.
* In the programmed-play mode, all programmed tracks are
repeatedly played.
* In the random-sequence play mode, all randomly sequenced
tracks are repeatedly played in the same order.
(OFF)
S/F REP
or
INDEX SEARCH
If the disc includes index numbers, play can be started from any desired index number.
REPEAT PLAY
You can play any desired track or disc (set of discs) repeatedly by pressing the REPEAT button. The repeat play mode will
change whenever you press the REPEAT button.
17
TRACK PROGRAMMING FOR RECORDING TO TAPE
This convenient feature can be used to program tracks for recording to tape. By only memorizing the tape’s total possible recording
time, the unit will automatically program tracks or help you to program tracks so they will fit onto the tape with the least amount of
unrecorded space remaining at each end of the tape.
Automatic tape programming
This is useful for recording a disc onto tape with the order of tracks unchanged.
1 Stop the unit.
2 Select the disc.
3 If necessary, select any desired DEQ-mode.
4 Enter the tape’s total possible recording time.
You can select any of four tape lengths by pressing
the TAPE button.
5 Otherwise, you can also enter the tape’s total possible
recording time manually.
Example: For a C-64 tape (32 minutes on each side)
6
* By pressing the REPEAT button, the unit automatically
programs tracks for side A and side B separately
considering the tape’s total time.
7 Begin recording on the tape deck and press the
PLAY/PAUSE button on this unit at the same time.
8 The unit will pause at the end of side A of the tape.
Turn the tape over to side B. Resume recording and,
at the same time, press the PLAY/PAUSE button on
this unit.
Notes
All tracks may not be programmed if the tape’s length is not
enough. To program all tracks, use a longer tape.
In step 6, you can check the program data for side A and
side B.
Shows the number of the first programmed track for each
side.
Shows the total time of programmed tracks for each side.
Shows the programmed track numbers for each side.
DEQ
CLASSIC
VOCAL
JAZZ
ROCK
1
10
2
34 5 6 78
90
+
TAPE
REPEAT
2
3
17,8
6
45
(off)
TAPE
1 Follow step 1, 4 and 5 on page 17.
2
3 If necessary, select the desired disc.
4 If necessary, select any desired DEQ-mode.
5 Select the desired track.
6 Repeat step 3–5 to set more programs for the side A
of the tape. You can select the same track again.
* If “E rr” appears in the display, the track number just
selected cannot be programmed because there is not
enough time remaining on the side A of the tape.
7 After you finish the programming for the side A,
program the pause mode by pressing the TAPE
button.
* “Pu” flashes in the display, and after then you can begin
programming for side B.
8 Follow step 3–5.
9 Repeat step 3–5 to set more programs for the side B
of the tape.
You can select the same track again.
* If “E rr” appears in the display, the track number just
selected cannot be programmed because there is not
enough time remaining on the side B of the tape.
10 Begin recording on the tape deck and press the
PLAY/PAUSE button on this unit at the same time.
11 The unit will pause at the end of side A of the tape.
Turn the tape over to side B. Resume recording
and, at the same time, press the PLAY/PAUSE
button on this unit.
Notes
If you will program tracks from more than one disc, before
you press the PROG button, check the total recorded time of
each disc on the disc tray by pressing the DISC SKIP button
in turn. Without this operation, the total remaining time of
each side of the tape and previously programmed track
numbers (and also unprogrammed track numbers) will not
be displayed during programming.
In step 6 and 9, even if “E rr” appears in the display, you can
program another track of which time is shorter than the
remaining time on the side of the tape. In this case, you can
check the remaining time on the side of the tape by pressing
the TIME display mode-select button.
Notes on tape programming
To check, cancel or correct program data, refer to page 13.
The maximum number of tracks that can be programmed is
40. If, however, the PAUSE mode is inserted, it is counted
as one track.
This function can be used to program up to track number 20.
If the disc has more than 20 tracks, track number 21 and
thereafter will not be programmed.
18
Manual tape programming
This is useful for recording desired tracks selected from one or several discs in any desired order onto tape.
1
10
2
34 5 6 78
90
+
TAPE
PROG
4
3
10,11
5
7
2
Flashes on and off.
19
Random sequential tape programming
The unit will automatically program tracks on a disc in random sequential order for recording to tape.
1 Follow step 1 – 5 on page 17.
2
* The unit will automatically program tracks for side A and
side B separately considering the tape’s total time.
3 Begin recording on the tape deck and press the
PLAY/PAUSE button on this unit at the same time.
4 The unit will pause at the end of side A of the tape.
Turn the tape over to side B. Resume recording and,
at the same time, press the PLAY/PAUSE button on
this unit.
Notes
Because the programmed data changes every time the
RANDOM button is pressed, the amount of time remaining at
the end of the tape also changes accordingly.
If the tape’s length is not enough, all tracks cannot be
programmed. In this case, exchange the tape for a longer
one.
In step 2, you can check the program data for side A and
side B.
Shows the number of programmed tracks for each side.
Shows the total time of programmed tracks for each side.
Shows the programmed track numbers for each side.
Display information during programming
Shows the side of the tape and the program number for the
track to be set next.
Shows the selected disc and track number.
Shows the total remaining time on the side of the tape.
Programmed track numbers illuminate and unprogrammed
ones flash on and off.
* If “A-01” does not appear in the display after the PROG
button is pressed, press the TIME display mode-select
button.
RANDOM
3,4
2
20
The 2nd/MAIN switch should be set while the units are in the
power-off mode.
When the units are not connected to each other, the
“2nd/MAIN” switch on the rear panel of each unit should be
set to the “MAIN” position.
Be sure to set the DIGITAL OUT ON/OFF switch on the rear
of each unit to the “OFF” position.
Relay play cannot be done if the DIGITAL OUT (COAXIAL)
terminal of the main unit is used for the connection to the
amplifier.
In the “SINGLE” disc play-mode
Discs are played alternately between the two units in
sequence.
In the “ALL” disc play-mode
After playing all discs in one unit, play will be switched to the
other automatically.
Disc play
If the power of both the units is switched on simultaneously, you can begin play from the first disc in the main unit. The operating
methods are the same as the normal disc play.
COAXIAL
DIGITAL OUT
ON
OFF
2nd CHANGER
INPUT
MAIN
2nd
CONTROL
L
R
LINE OUT
RELAY PLAY
COAXIAL
DIGITAL OUT
ON
OFF
2nd CHANGER
INPUT
MAIN
2nd
CONTROL
L
R
LINE OUT
RELAY PLAY
To amplifier
Main unit
2nd unit
Set to “MAIN” .
Set to “2nd” .
L
R
L
R
Remote control cable (separate purchase)
1
2
3
4
5
1
2
3
4
5
MAIN
2nd
1
5
2
4
3
2nd
1
5
2
4
3
MAIN
RELAY PLAY
If you have two CDC-835s, you can enjoy any combination play of ten discs by connecting them to each other.
Connections
At first, determine which CDC-835 is to be used as the main unit (or the second one). Connections should be made as shown in the
following figure.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24

Yamaha CDC-835 Le manuel du propriétaire

Catégorie
Lecteur CD
Taper
Le manuel du propriétaire