CyberPower RWCCARD100 Mode d'emploi

CyberPower
Marque
CyberPower
Modèle
RWCCARD100
Taper
Mode d'emploi

Ce manuel convient également à

REMOTE WIRELESS CLOUD CARD
RWCCARD100
REMOTE WIRELESS CLOUD CARD
RWCCARD100
Copyright © 2021 Cyber Power Systems, Inc. All rights reserved.
2
31
INSTALLATION GUIDE
NOTE: The Remote Wireless Cloud Card is hot-swappable,
so you do not need to turn o the device to install it.
NOTE: You can reset the Remote Wireless Cloud
Card back to its factory settings by pressing and
holding the Reset button. It will begin to flash blue
once it’s reset.
3. Insert and tighten the
retaining screws.
4. Please ensure the LED
Status is flashing blue.
2. Install the Remote Wireless
Cloud Card into the
expansion slot.
1. Remove the two retaining
screws from the expansion
slot, and remove the cover.
Step 1. Hardware Installation
Definitions for the LED Indicators
LED Status (Color)
Blue
(Flashing)
Green
(Flashing)
Green
Condition
The Remote Wireless Cloud Card is not
connected to the Router.
The Remote Wireless Cloud Card is being
connected to the Network.
The Remote Wireless Cloud Card is
connected to the Network.
Step 2. Application Installation
Install the “POWERPANEL” application available for download on
the Apple App Store or Google Play, then launch the application.
Reset Button
Network Indicator
Step 4. Add a device in the POWERPANEL app
1. Click “+” in the upper right corner of the homepage, as shown in
Figure 2.
Figure 2
Figure 1
Step 3. Sign Up and Login, as shown in Figure 1
iOS Android
Quick Start Guide
STATUS
RESET
Power
RWCCARD100
Cloud
K01-0000852-01
6
75
4
Cyber Power Systems, Inc.
www.cyberpower.com
For USA and Canada:
4241 12th Ave East, Suite 400
Shakopee, MN 55379
Toll-free: (877) 297-6937
For all other regions:
Please visit our website for local contact information.
Figure 3
2. Select “Add Device by WiFi” to add your Remote Wireless
Cloud Card.
3. Connect the Remote Wireless Cloud Card you are installing.
- Go to your phone's Settings > Wi-Fi
- Make sure the Wi-Fi is turned on, and choose the network, like the
example below, to connect to the wireless card
- Enter the default password: cyberpower
- Once connected, return to the application
NOTE: If you were not prompted to turn on your phone's location, verify it’s
on now.
4. If the Remote Wireless Cloud Card is connected, then you will see
“Setting WiFi” on the bottom of the page.
5. Select and connect to your Wi-Fi router and name the device you
are monitoring.
6. After the setup is completed, you will see your device on the
homepage, as shown in Figure 3.
7. Wait till successful configuration, as shown in Figure 4.
Figure 4
Step 5. Start monitoring your UPS!
In addition to the app, you can access the PowerPanel® Cloud account
via a web browser: https://powerpanel.cyberpower.com
For more information, please refer to the PowerPanel®Cloud
User’s Manual.
Figure 5
Figure 6
FIRMWARE UPGRADE
Keep your RWCCARD100 up to date with the newest features and
improvements. Ensure your RWCCARD100 has the latest version of
firmware by selecting access “Device Setting” / “Card Firmware Update”
in the PowerPanel
App or the PowerPanel
Cloud web browser
periodically to check for updates, as shown in Figure 5 and 6.
CONFORMANCE APPROVALS
FCC Statement:
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment o and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device contains licence-exempt transmitter(s) that comply with Innovation,
Science and Economic Development Canada’s licence-exempt RSS(s). Operation is
subject to the following two conditions:
(1) this device may not cause interference,
(2) this device must accept any interference, including interference that may cause
undesired operation of the device.
L’émetteur exempt de licence contenu dans le présent appareil est conforme aux CNR
d’Innovation, Sciences et Développement économique Canada applicables aux
appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes :
(1) L’appareil ne doit pas produire de brouillage;
(2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d’en compromettre le fonctionnement.
Canadian Compliance Statement
CAN ICES-3 (B)/NMB-3(B)
  • Page 1 1
  • Page 2 2

CyberPower RWCCARD100 Mode d'emploi

CyberPower
Marque
CyberPower
Modèle
RWCCARD100
Taper
Mode d'emploi
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Autres documents