Greenlee HID6506 - 42309 Rotary Impact Drill Manuel utilisateur

Marque: Greenlee

Modèle: HID6506 - 42309 Rotary Impact Drill

Catégorie: Outils électroportatifs

Taper: Manuel utilisateur

Ce manuel convient également à

HID6506 - 42309 Rotary Impact Drill Manual

Hydraulic

Rotary Impact Drill

Serial Code AML

OPERATION MANUAL

Read and understand all of the instructions and

safety information in this manual before operating

or servicing this tool.

Español ............... 15

Français .............. 29

Hydraulic Rotary Impact Drill

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

Table of Contents

Description .................................................................... 2

Safety ............................................................................ 2

Purpose of this Manual ................................................. 2

Other Publications ......................................................... 2

Important Safety Information .....................................3–5

Identication .................................................................. 6

Specications ................................................................ 7

Setting the Super Spool ................................................ 8

Setting the Tool to Drill or Hammer Drill ........................ 8

Installing and Removing Drill Bits .................................. 9

Hoses and Fittings ...................................................... 10

Typical Setup ............................................................... 10

Hose Connections ....................................................... 10

Operation ..................................................................... 11

Maintenance ................................................................ 12

Troubleshooting ........................................................... 13

Español ........................................................................ 15

Français ....................................................................... 29

Deutsch ....................................................................... 43

Italiano ......................................................................... 57

Description

The Greenlee Hydraulic Rotary Impact Drill is intended

for use with impact-type bits for hammer (impact) drill-

ing in concrete, brick, rock and other difcult-to-drill

materials.

Features include a depth gauge, a directional spool for

forward or reverse operation, Super Spool™ for use

on either an Open-Center or Closed-Center hydraulic

system, and an insulated handle for operator comfort

and safety. A ow control cartridge, effective with

Serial Number 300, limits the hydraulic ow to 24.6 l/min

(6.5 gpm), allowing the tool to be connected to a

hydraulic system providing up to 45.4 l/min (12 gpm).

The tool also includes a variable torque output screw

and a built-in safety slip clutch to help prevent operator

injury if the drill bit catches.

Super Spool is protected by U.S. Patent No. 4548229.

KEEP THIS MANUAL

Safety

Safety is essential in the use and maintenance of

Greenlee tools and equipment. This instruction manual

and any markings on the tool provide information for

avoiding hazards and unsafe practices related to the

use of this tool. Observe all of the safety information

provided.

Purpose of this Manual

This manual is intended to familiarize personnel with

the safe operation and maintenance procedures for the

following Greenlee tool:

HID6506 (42309) Hydraulic Rotary Impact Drill

Serial Code AML

Keep this manual available to all personnel.

Replacement manuals are available upon request at no

charge at www.greenlee.com.

Other Publications

Tool Owners/Users

SAE Standard J1273 (Hose and Hose Assemblies):

Publication 99930323

Authorized Greenlee Service Centers

Repair Manual: Publication 99915979

All specications are nominal and may change as design

improvements occur. Greenlee Tools, Inc. shall not be liable for

damages resulting from misapplication or misuse of its products.

Super Spool is a trademark of Greenlee Tools, Inc.

Hydraulic Rotary Impact Drill

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

IMPORTANT SAFETY INFORMATION

SAFETY

ALERT

SYMBOL

This symbol is used to call your attention to hazards

or unsafe practices which could result in an injury or

property damage. The signal word, dened below,

indicates the severity of the hazard. The message

after the signal word provides information for

preventing or avoiding the hazard.

Immediate hazards which, if not avoided, WILL result

in severe injury or death.

Hazards which, if not avoided, COULD result in

severe injury or death.

Hazards or unsafe practices which, if not avoided,

MAY result in injury or property damage.

Read and understand all of the

instructions and safety information

in this manual before operating or

servicing this tool.

Failure to observe this warning could

result in severe injury or death.

Wear eye protection when operating

or servicing this tool.

Failure to wear eye protection could

result in serious eye injury from ying

debris or hydraulic oil.

Wear hearing protection when using

this tool.

Failure to observe this warning could

result in serious injury.

Electric shock hazard:

This tool is not insulated. When

using this unit near energized electri-

cal lines:

• Use only certied non-conductive

hoses and proper personal protec-

tive equipment.

• Select and maintain the hydraulic

uid to meet the minimum dielec-

tric standards required by your

safety department.

Failure to observe this warning could

result in severe injury or death.

Skin injection hazard:

• Do not use ngers or hands to

check for leaks.

• Do not hold hose or couplers while

the hydraulic system is pressurized.

• Depressurize the hydraulic system

before servicing.

Oil under pressure easily punctures

skin causing serious injury, gangrene

or death. If you are injured by

escaping oil, seek medical attention

immediately.

Hydraulic Rotary Impact Drill

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

IMPORTANT SAFETY INFORMATION

• When using the tool in hammer drill mode, use

accessories that are approved for impact use

only. Accessories that are not approved for impact

applications can break when used in the hammer

drill mode.

• Inspect accessories before use. Discard accesso-

ries that have cracks, chips or gauges.

Failure to observe these warnings could result in

severe injury or death.

Some dust created by power sanding, sawing, grind-

ing, drilling, and other construction activities contains

chemicals known to the State of California to cause

cancer, birth defects or other reproductive harm.

Some examples of these chemicals are:

• Lead from lead-based paints

• Crystalline silica from bricks and cement and other

masonry products

• Arsenic and chromium from chemically-treated

lumber.

To reduce your exposure to these chemicals: work in

a well ventilated area, and work with approved safety

equipment, such as dust masks that are specially

designed to lter out microscopic particles.

• Remove the chuck key from the chuck before drill-

ing. Operation with the key in the chuck can result

in severe injury.

• Keep all parts of the body away from rotating parts

when the tool is in operation. Contact with moving

parts can result in severe injury.

• Do not change accessories, inspect or clean tool

when it is connected to a power source. Accidental

start-up can result in serious injury.

• Maintain a rm grip on tool, using both hands at all

times. Serious injury can result if an operator does

not control the tool.

• Do not lock trigger in the power-ON position.

Operator cannot stop tool when trigger is locked.

Failure to observe these warnings could result in

severe injury or death.

Tool and accessory may be hot

during and after operation.

Contact with hot surfaces could

result in serious injury.

Do not exceed the following hydraulic power source

maximums:

• Hydraulic ow: 45.4 l/min (12 gpm)

• Pressure relief setting: 138 bar (2000 psi)

• Back pressure: 13.8 bar (200 psi)

Failure to observe this warning could result in severe

injury or death.

Do not disconnect tool, hoses, or ttings while

the tool is running or if the hydraulic uid is

hot. Hot hydraulic uid can cause serious burns.

Do not reverse hydraulic ow. Operation with

hydrau-

lic ow reversed can cause tool malfunction.

Connect

the supply (pressure) hose and return (tank) hose to

the proper tool ports.

Failure to observe this warning could result in severe

injury or death.

Hydraulic Rotary Impact Drill

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

IMPORTANT SAFETY INFORMATION

• Wear protective gloves when handling, removing,

and installing drill bits. Drill bits can cut even when

stationary.

• Inspect tool before use. Replace any worn

or damaged parts. A damaged or improperly

assembled tool can malfunction, injuring nearby

personnel.

• Inspect the hydraulic hoses and couplings every

operating day. Repair or replace if leakage, crack-

ing, wear, or damage is evident. Damaged hoses

or couplings can fail, resulting in injury or property

damage.

• Use this tool for manufacturer’s intended use only.

Use other than that which is described in this

manual could result in injury or property damage.

• Make sure all bystanders are clear of the work area

when handling, starting, and operating the tool.

Nearby personnel can be injured by ying parts in

the event of a tool malfunction.

Prolonged exposure to vibration or very repetitive

hand and arm movements may cause injury. Stop

using any tool if discomfort, tingling feeling, or pain

occurs. Consult a physician before resuming use of

the tool.

Procedure for disconnecting hydraulic hoses, ttings

or components:

1. Move the ow lever on the hydraulic power

source to the OFF position.

2. Stop the power source.

3. Follow the sequence under Disconnecting Hoses

to prevent pressure buildup. In case some

pressure has built up, loosen hoses, ttings, or

components slowly.

Emergency stop procedure:

1. Release the trigger.

2. Shut off the hydraulic power source.

Note: Keep decals clean and legible. Replace decals

when necessary—see the decals listed in the Service

manual.

Hydraulic Rotary Impact Drill

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

Identiﬁcation

1. Trigger

2. Drill/Hammer Drill Selector Knob

3. Collar

4. Depth Gauge

5. Auxiliary Handle

6. Lifting Hook

7. Motor Cap

Hydraulic Rotary Impact Drill

8. Serial Number

9. Super Spool

10. Directional Spool

11. Handle

12. Tank Port

13. Pressure Port

14. Variable Torque Output Screw

Hydraulic Rotary Impact Drill

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

Hydraulic Rotary Impact Drill

Type of Hydraulic System .......................Open-Center or

Closed-Center

Hydraulic Pressure Port .............3/4–16 SAE O-ring Boss

Hydraulic Tank Port ...................3/4–16 SAE O-ring Boss

Bits

SDS Plus Type Chuck ................ SDS Plus Type Shank

Noise Levels

Sound Power Level (maximum) ..........................85 L

Mass/Weight ................................................ 4.1 kg (9 lbs)

Length ..................................................... 285 mm (11.2")

Width ........................................................... 89 mm (3.5")

Height ...................................................... 280 mm (11.0")

Output

Revolutions per Minute @ 18.9 l/min (5 gpm) .........900

Revolutions per Minute @ 22.7 l/min (6 gpm) .......1050

Impacts per Minute @ 22.7 l/min (6 gpm) .............5400

Max. Single Impact Energy ...................................2.4 J

Drilling Capacity

Concrete ...................................................22 mm (7/8")

Steel ......................................................... 13 mm (1/2")

Wood .....................................................30 mm (1-1/8")

Core Bit .................................................68 mm (2-5/8")

Hydraulic Power Source

Do not exceed the following hydraulic power source

maximums:

• Hydraulic ow: 45.4 l/min (12 gpm)

• Pressure relief setting: 138 bar (2000 psi)

• Back pressure: 13.8 bar (200 psi)

Failure to observe this warning could result in severe

injury or death.

Type of Hydraulic System ........................Open-Center or

Closed-Center

Flow

Minimum ..........................................15.1 l/min (4 gpm)

Recommended .................................22.7 l/min (6 gpm)

Maximum .......................................45.4 l/min (12 gpm)

Pressure Relief Setting

Minimum .........................................68.9 bar (1000 psi)

Maximum .........................................138 bar (2000 psi)

Filtration ............................................ 10 micron (nominal)

Back Pressure (maximum)* ..................13.8 bar (200 psi)

* 13.8 bar (200 psi) is the maximum agreed standard back pressure

for the HTMA (Hydraulic Tool Manufacturers Association).

Greenlee tool will operate satisfactorily at this standard.

1. Maximum hydraulic uid temperature must not

exceed 60 °C (140 °F). A sufcient oil cooling

capacity is needed to limit the hydraulic uid

temperature.

2. Hydraulic ow must not exceed 45.4 l/min (12 gpm).

Install a ow meter in the return line to measure the

rate of hydraulic ow before using the tool.

3. Pressure relief valve setting must not exceed

138bar (2000 psi) at your tool’s maximum ow.

Locate the pressure relief valve in the supply circuit

to limit excessive hydraulic pressure to the tool.

Hydraulic Schematic

FILTER

(10 MICRON)

COOLER

RELIEF

VALVE

138 bar

(2000 psi)

CONTROL

VALVE

FLOW METER

TOOL

RESERVOIR

PUMP

POWER SOURCE

Recommended Hydraulic Fluids

Use any non-detergent, petroleum-based hydraulic

uid which meets the following specications or HTMA

specications.

S.U.S. @:

38 °C (100 °F) ...............................................140 to 225

99 °C (210 °F) ............................................40 minimum

Flash Point ................................170 °C (340 °F) minimum

Pour Point ..................................-34 °C (-30 °F) minimum

Speciﬁcations

Hydraulic Rotary Impact Drill

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

Setting the Super Spool

The Super Spool allows the tool to be used with either

Open-Center or Closed-Center hydraulic systems.

Open-Center Hydraulic System

Use a wrench to turn the Super Spool until the letter “O”

on the spool is aligned with the letter “C” on the tool

handle.

Closed-Center Hydraulic System

Use a wrench to turn the Super Spool until the letter “C”

on the spool is aligned with the letter “C” on the tool

handle.

Setting the Tool to Drill

or Hammer Drill

The drill/hammer drill selector knob allows the tool to

be used for either standard drilling or hammer (impact)

drilling. Depress the red indication arrow (1) to turn the

selector knob.

Set the knob so that the red arrow icon (1) points to the

desired operation:

• Drill bit icon (2) for standard drilling

• Hammer icon (3) for hammer drilling

Setting the Super Spool

Closed-Center Open-Center

Hydraulic Rotary Impact Drill

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

Installing and Removing Drill Bits

Greenlee recommends using Greenlee impact-style bits.

See Accessories in this manual.

• When using the tool in hammer drill mode, use

accessories that are approved for impact use

only. Accessories that are not approved for impact

applications can break when used in the hammer

drill mode.

• Inspect accessories before use. Discard accesso-

ries that have cracks, chips or gauges.

Failure to observe these warnings could result in

severe injury or death.

Some bits may whip or bend under sideload.

• Do not use bits with a long spiral and center

support.

• When using an impact bit, run the power source

at the minimum ow. Refer to the “Specications”

section.

Failure to observe this warning could result in severe

injury or death.

Long SpiralCenter Support

SDS Plus Type Chuck

1. Inspect the chuck. Remove any dirt or other

contamination.

2. Select an SDS Plus type of bit. Align the long slots

in the shank of the bit with the index mark in the

dust cover on the end of the collar. Insert the bit into

the chuck.

3. Check to make sure the collar is securely holding

the bit.

4. To remove the drill bit, twist the collar so that it

releases the bit.

Hydraulic Rotary Impact Drill

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

Hose Connections

Tool Port Identiﬁcation

One of three methods is used to identify the pressure

and tank ports of Greenlee tools. Match the markings on

your tool to this table.

Pressure Port Tank Port

P T

In Out

Connecting Hoses

1. Move the ow lever on the hydraulic power source

to the OFF position.

2. Stop the hydraulic power source.

3. Connect the tank hose to the tank port on the

power source, and then to the tank port on the tool.

Connect the pressure hose to the pressure port on

the tool, and then to the pressure port on the power

source.

Disconnecting Hoses

1. Move the ow lever on the hydraulic power source

to the OFF position.

2. Stop the hydraulic power source.

3. Disconnect the pressure hose from the power

source, and then from the tool.

4. Disconnect the tank hose from the tool, and then

from the power source.

5. Install dust caps over the ports to prevent

contamination.

Hoses and Fittings

Installation and Maintenance

See publication 99930323, SAE Standard J1273

(Hoseand Hose Assemblies).

Replacement

See a Greenlee catalog or Greenlee publication

99910322, Low Pressure Quick Couplers,

Adapters and Hoses.

Do not disconnect tool, hoses, or ttings while

the power source is running or if the hydraulic uid is

hot. Hot hydraulic uid could cause serious burns.

Typical Setup

Hydraulic Rotary Impact Drill

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

Operation

Wear eye protection when operating

or servicing this tool.

Failure to wear eye protection could

result in serious eye injury from ying

debris or hydraulic oil.

Electric shock hazard:

This tool is not insulated. When

using this unit near energized electri-

cal lines:

• Use only certied non-conductive

hoses and proper personal protec-

tive equipment.

• Select and maintain the hydraulic

uid to meet the minimum dielec-

tric standards required by your

safety department.

Failure to observe this warning could

result in severe injury or death.

Skin injection hazard:

• Do not use ngers or hands to

check for leaks.

• Do not hold hose or couplers while

the hydraulic system is pressurized.

• Depressurize the hydraulic system

before servicing.

Oil under pressure easily punctures

skin causing serious injury, gangrene

or death. If you are injured by

escaping oil, seek medical attention

immediately.

• When using the tool in hammer drill mode, use

accessories that are approved for impact use

only. Accessories that are not approved for impact

applications can break when used in the hammer

drill mode.

• Inspect accessories before use. Discard accesso-

ries that have cracks, chips or gauges.

Failure to observe these warnings could result in

severe injury or death.

1. Stop the hydraulic power source.

2. Set the Super Spool, select the drill or hammer drill

operating mode, and install a bit as described

in the previous sections of this manual. Set the

directional spool to the appropriate position

(forward or reverse).

3. Connect the tool to the power source according to

the instructions under Hose Connections.

• Do not operate the tool with the Drill/Hammer Drill

selector knob in a position between drilling and

hammer drilling.

• Allow the tool to stop before changing the position

of the drill/hammer drill selector knob.

• Do not change the position of the directional spool

while the tool is operating. Allow the tool to stop

before changing direction.

4. Start the power source.

5. Grasp the trigger handle with one hand, and grasp

the auxiliary handle with your other hand. This will

allow you to apply leverage while operating the tool.

6. To start the tool, squeeze the trigger.

Note: Use the variable torque adjustment screw

to achieve the necessary amount of torque. Turn

the screw counterclockwise to increase torque, or

clockwise to decrease torque.

7. To stop the tool, release the trigger.

8. When the tool is not in use, stop the power source

to reduce heat and wear on the tool.

Hydraulic Rotary Impact Drill

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

Maintenance

Do not change accessories, inspect or clean tool or

accessories when it is connected to a power source.

Accidental start-up can result in serious injury.

Failure to observe this warning could result in severe

injury or death.

Wear eye protection when operating

or servicing this tool.

Failure to wear eye protection could

result in serious eye injury from ying

debris or hydraulic oil.

Use this maintenance schedule to maximize the tool’s

service life.

Notes: Keep all decals clean and legible. Replace

decals when necessary. Refer to the Service manual for

decal part numbers.

When disposing of any components (hydraulic hoses,

hydraulic ﬂuid, worn parts, etc.), do so in accordance

with federal, state, and local laws or ordinances.

Daily

1. Wipe all tool surfaces clean.

Inspect the hydraulic hoses and ttings for signs of

leaks, cracks, wear or damage. Replace if necessary.

3. Install dust caps over the hydraulic ports when the

tool is disconnected.

Monthly

Perform a thorough inspection of the hydraulic hoses

and ttings as described in publication 99930323,

SAE J1273 (Hose and Hose Assemblies).

Annually

If required by your organization’s regulations, have the

tool inspected by an authorized Greenlee service center.

Hydraulic Rotary Impact Drill

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

Problem Probable Cause Probable Remedy

Tool does not operate. Improper power source. Refer to the “Specications” section.

Verify that the power source meets the

specications.

Hydraulic uid level low. Check the uid level. Check system for leaks.

Incorrect hydraulic uid viscosity. Refer to “Recommended Hydraulic Fluids” in

the “Specications” section.

Hose connections at tool reversed. Depressurize hydraulic system. Switch the

hose connections.

Variable torque adjustment screw

turned too far clockwise, completely

stopping the ow of hydraulic uid.

Turn the variable torque adjustment screw

counterclockwise to achieve the necessary

amount of torque.

Tool operates slowly or

erratically.

Hydraulic uid cold. Allow uid to warm to the operating tempera-

ture. Actuate the tool intermittently to reduce

the warming time.

Power source not adjusted correctly. Refer to the power source operator’s manual

for setting the ow and pressure. Set the ow

and pressure to correspond with the tool.

Air in the hydraulic system. See power source manufacturer’s instructions

for removing air from the system.

Incorrect hydraulic uid viscosity. Refer to “Recommended Hydraulic Fluids” in

the “Specications” section.

Tool feels hot. Hydraulic uid level low. Check the uid level. Check system for leaks.

Incorrect hydraulic uid viscosity. Refer to “Recommended Hydraulic Fluids” in

the “Specications” section.

Hydraulic uid dirty. Drain reservoir; ush and ll with clean uid.

Change lter.

Before troubleshooting, determine whether the problem

is in the tool, the hoses, or the power source. Substitute

a tool, hoses, or power source known to be in good

working order to eliminate the item that is not operating.

If the problem is in the tool, see the troubleshoot-

ing table in this manual. If the problem is in the power

source, see the troubleshooting section of the power

source instruction manual.

Troubleshooting

4455 Boeing Drive • Rockford, IL 61109-2988 • USA • 815-397-7070

USA Tel: 800-435-0786

Fax: 800-451-2632

Canada Tel: 800-435-0786

Fax: 800-524-2853

International Tel: +1-815-397-7070

Fax: +1-815-397-9247

www.greenlee.com

Taladro de Percusión

Rotatorio Hidráulico

Código de serie AML

MANUAL DE OPERACIÓN

Lea y entienda todas las instrucciones y la

información sobre seguridad que aparecen en

este manual, antes de manejar esta herramienta o

darle mantenimiento.

Registre este producto en www.greenlee.com

Taladro de Percusión Rotatorio Hidráulico

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

Índice

Descripción ................................................................. 16

Acerca de la seguridad ................................................ 16

Propósito de este manual ........................................... 16

Otras publicaciones .................................................... 16

Importante Información sobre Seguridad ..............17–19

Identicación ............................................................... 20

Especicaciones ......................................................... 21

Montaje del Super Spool ............................................. 22

Montaje de la herramienta al taladro

o al taladro de martillo ................................................. 22

Instalación y remoción de las brocas para taladro...... 23

Mangueras y accesorios ............................................. 24

Modelo de instalación ................................................. 24

Conexión de las mangueras ........................................ 24

Operación .................................................................... 25

Mantenimiento ............................................................. 26

Diagnóstico y solución de fallas .................................. 27

Descripción

El Taladro de Percusión Rotatorio Hidráulico de

Greenlee ha sido diseñado a n de utilizarse con brocas

de percusión para perforar con fuerza de impacto

hormigón, ladrillo, roca y otros materiales difíciles

de taladrar.

Entre las características se cuentan un calibre

de profundidad, una bobina direccional para

funcionamiento hacia adelante y en reversa, Super

Spool™ para uso en sistemas hidráulicos de circuito

abierto o cerrado, y una empuñadura aislada para

brindarle comodidad y seguridad al operador. Un

cartucho para control de gasto, comenzando con el

Número de Serie 300, limita el gasto hidráulico a

24,6l/min (6,5 gpm), permitiendo que la herramienta se

conecte a un sistema hidráulico que proporcione hasta

45,4 l/min (12 gpm). La herramienta incluye además

un tornillo de salida de par de torsión variable y un

embrague deslizante de seguridad para ayudar a evitar

que el operador se lesione si la broca para taladro se

atasca.

Super Spool está protegido por la patente

estadounidense No. 4548229.

CONSERVE ESTE MANUAL

Acerca de la seguridad

Es fundamental observar métodos seguros al utilizar

y dar mantenimiento a las herramientas y equipo

Greenlee. Este manual de instrucciones y todas

las marcas que ostenta la herramienta le ofrecen la

información necesaria para evitar riesgos y hábitos

poco seguros relacionados con su uso. Siga toda la

información sobre seguridad que se proporciona.

Propósito de este manual

Este manual tiene como propósito familiarizar al

personal con los procedimientos de operación y

mantenimiento seguros para la siguiente herramienta

Greenlee:

Taladro de Percusión Rotatorio Hidráulico

HID6506 (42309)

Código de serie AML

Mantenga siempre este manual al alcance de todo el

personal.

Puede obtener copias adicionales de manera gratuita,

previa solicitud en www.greenlee.com.

Otras publicaciones

Para propietarios o usuarios

Norma SAE J1273 (Manguera y conjuntos de

mangueras): Publicación 99930323

Centros de Servicio Autorizado Greenlee

Manual de reparación: Publicación 99915979

Todas las especicaciones son nominales y pueden cambiar conforme

tengan lugar mejoras de diseño. Greenlee Tools, Inc. no se hace

responsable de los daños que puedan surgir de la mala aplicación o

mal uso de sus productos.

Super Spool es una marca registrada de Greenlee Tools, Inc.

Taladro de Percusión Rotatorio Hidráulico

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

IMPORTANTE INFORMACIÓN SOBRE SEGURIDAD

SÍMBOLO

DE ALERTA

SOBRE

SEGURIDAD

Este símbolo se utiliza para indicar un riesgo o

práctica poco segura que podría ocasionar lesiones

o daños materiales. Cada uno de los siguientes

términos denota la gravedad del riesgo. El mensaje

que sigue a dichos términos le indica cómo puede

evitar o prevenir ese riesgo.

Peligros inmediatos que, de no evitarse,

OCASIONARÁN graves lesiones o incluso la muerte.

Peligros que, de no evitarse, PODRÍAN

OCASIONAR graves lesiones o incluso la muerte.

Peligro o prácticas peligrosas que, de no evitarse,

PUEDEN OCASIONAR lesiones o daños materiales.

Lea y entienda todas las

instrucciones y la información sobre

seguridad que aparecen en este

manual, antes de manejar esta

herramienta o darle mantenimiento.

De no observarse esta advertencia

pueden sufrirse graves lesiones o

incluso la muerte.

Utilice protectores para ojos al

manejar o darle mantenimiento a

esta herramienta.

De no utilizar protectores para ojos

puede sufrir graves lesiones oculares

ocasionadas si el aceite para

aparatos hidráulicos, o restos de

materiales llegaran a saltar.

Al manejar esta herramienta utilice

protección auditiva.

De no observarse esta advertencia

podrían sufrirse lesiones graves.

Peligro de electrocución:

Esta herramienta no está aislada. Al

utilizar esta unidad cerca de líneas

eléctricas energizadas:

• Utilice únicamente mangueras no

conductivas aprobadas y equipo de

protección personal adecuado.

• Seleccione siempre un líquido

para aparatos hidráulicos, que

cumpla con los estándares

dieléctricos mínimos exigidos por

su departamento de seguridad, y

manténgalo al nivel adecuado.

De no observarse esta advertencia

pueden sufrirse graves lesiones o

incluso la muerte.

Peligro de inyección cutánea:

• No use los dedos ni las manos para

localizar fugas.

• No toque la manguera ni los

acopladores mientras el sistema

hidráulico se encuentre presurizado.

• Purgue la presión en el sistema

hidráulico antes de darle

mantenimiento.

El aceite bajo presión punza la

piel fácilmente provocando graves

lesiones, gangrena o la muerte. Si se

lesiona debido a una fuga de aceite,

solicite atención médica de inmediato.

Taladro de Percusión Rotatorio Hidráulico

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

IMPORTANTE INFORMACIÓN SOBRE SEGURIDAD

• Cuando opere la herramienta en el modo de

taladro de martillo, utilice únicamente accesorios

aprobados para aplicaciones donde sea necesaria

la fuerza por percusión. Los accesorios que no han

sido aprobados para este tipo de aplicaciones se

pueden quebrar al utilizarse en el modo de taladro

de martillo.

• Revise minuciosamente los accesorios antes de

utilizarlos. Deseche aquéllos que presenten grietas,

mellas o desportilladuras.

De no observarse estas advertencias pueden sufrirse

graves lesiones o incluso la muerte.

Algunos polvos generados por el lijado, aserrado,

amolado, taladrado con herramienta eléctrica y otras

actividades de construcción contienen sustancias

químicas que el Estado de California conoce como

causantes de cáncer, defectos congénitos u otros

daños al sistema reproductor. Algunos ejemplos de

estos químicos son los siguientes:

• Plomo de las pinturas con base de plomo

• Sílice cristalina de los ladrillos y cementos, y de

otros productos de mampostería

• Arsénico y cromo de la madera tratada

químicamente.

A n de reducir su exposición a estas sustancias

químicas: trabaje en un área bien ventilada, y

trabaje con equipo de seguridad apropiado, tal

como mascarillas contra polvo que están diseñadas

especialmente para ltrar partículas microscópicas.

• Retire del portabrocas la llave del portabrocas

antes de perforar. Hacer funcionar la herramienta

con la llave en el portabrocas puede ocasionar

graves lesiones.

• Mantenga todas las partes del cuerpo alejadas de

las piezas giratorias siempre que la herramienta

esté en funcionamiento. El contacto con las piezas

en movimiento puede ocasionar graves lesiones.

• No cambie accesorios ni inspeccione o limpie la

herramienta mientras esté conectada a una fuente

de potencia. Si ésta se activa accidentalmente,

podría ocasionar graves lesiones.

• Siempre sostenga la herramienta rmemente con

ambas manos. Si pierde el control de la unidad

podría ocasionar graves lesiones.

• No trabe el gatillo en la posición “ON”. El operador

no podrá detener la herramienta si se encuentra

trabada en dicha posición.

De no observarse estas advertencias pueden sufrirse

graves lesiones o incluso la muerte.

Tanto la herramienta como los

accesorios pueden alcanzar

temperaturas sumamente altas

mientras están en operación o

incluso una vez que han sido

apagados.

El contacto con supercies calientes

puede producir lesiones graves.

No exceda los máximos a continuación para la

fuente de potencia hidráulica:

• Gasto hidráulico: 45,4 l/min

• Ajuste de la presión de seguridad: 138 bar

• Contrapresión: 13,8 bar

De no observarse esta advertencia podrían sufrirse

graves lesiones o incluso la muerte.

Taladro de Percusión Rotatorio Hidráulico

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

IMPORTANTE INFORMACIÓN SOBRE SEGURIDAD

No desconecte la herramienta, ni las mangueras o

accesorios mientras la unidad esté encendida o el

líquido hidráulico esté caliente. El líquido hidráulico

caliente puede ocasionar quemaduras graves.

No invierta el gasto hidráulico. Operar la herramienta

con el gasto invertido ocasionará un funcionamiento

inadecuado.HORIZONTAL 100> Conecte las

mangueras de suministro (presión) y la de retorno

(tanque), en los oricios correspondientes en la

herramienta.

De no observarse esta advertencia pueden sufrirse

graves lesiones o incluso la muerte.

• Utilice guantes protectores al manipular, retirar

o colocar las brocas para taladro; éstas pueden

cortar incluso cuando no están en movimiento.

• Revise la herramienta antes de utilizarla.

Reemplace cualquier pieza desgastada o dañada.

Una herramienta dañada o montada de manera

incorrecta tendrá un funcionamiento errático y

puede lesionar al personal que se encuentre en el

área.

• Revise minuciosamente las mangueras hidráulicas

y los acoplamientos cada vez que vaya a utilizar la

herramienta. Repárelos o reemplácelos si presentan

fugas, grietas, desgaste o daños evidentes. Las

mangueras y acoplamientos averiados pueden fallar

y ocasionar lesiones o daños materiales.

• Utilice la herramienta únicamente para el uso

para el que ha sido diseñada por el fabricante. Si

se utiliza de una manera distinta a la descrita en

este manual puede ocasionarse lesiones o daños

materiales.

• Asegúrese de que no haya circunstantes en

el área de trabajo al manipular la herramienta,

ponerla en funcionamiento o manejarla, El personal

del área podría sufrir lesiones si alguna pieza

saliera disparada al haber un desperfecto de la

herramienta.

La exposición prolongada a la vibración o

movimientos muy repetidos de manos y brazos

puede causar lesiones. Detenga el uso de cualquier

herramienta si siente incomodidad, hormigueo o

dolor. Consulte a un médico antes de reanudar el uso

de la herramienta.

Procedimiento para desconectar las mangueras,

accesorios o demás componentes hidráulicos:

1. Coloque la palanca de gasto –ubicada en la

fuente de potencia hidráulica– en la posición de

apagado (OFF).

2. Apague la fuente de potencia.

3. Siga la secuencia detallada en “Desconexión de

las mangueras” a n de evitar la acumulación

de presión. En caso de que esto ocurra, aoje

lentamente las mangueras, los accesorios o los

componentes.

Procedimiento de apagado de emergencia:

1. Suelte el gatillo.

2. Apague la fuente de potencia hidráulica.

Nota: Mantenga las etiquetas de advertencia limpias y

legibles. Reemplace las etiquetas según sea necesario.

Véase la lista de etiquetas en el Manual de reparación.

Taladro de Percusión Rotatorio Hidráulico

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

Identiﬁcación

1. Gatillo

2. Perilla de Selección de Taladro/

Taladro de Martillo

3. Collarín

4. Calibre de Profundidad

5. Empuñadura Auxiliar

6. Gancho de Izar

7. Tapa del Motor

Taladro de Percusión Rotatorio Hidráulico

8. Número de Serie

9. Super Spool

10. Carrete Direccional

11. Empuñadura

12. Oricio del Tanque

13. Oricio de Presión

14. Tornillo de Salida de Par de

Torsión Variable

La page charge ...

Greenlee HID6506 - 42309 Rotary Impact Drill Manuel utilisateur

Marque: Greenlee

Modèle: HID6506 - 42309 Rotary Impact Drill

Catégorie: Outils électroportatifs

Taper: Manuel utilisateur

Ce manuel convient également à

HID6506 - 42309 Rotary Impact Drill Manual

Télécharger le PDF

rapport

dans d''autres langues

English: Greenlee HID6506 - 42309 Rotary Impact Drill User manual
español: Greenlee HID6506 - 42309 Rotary Impact Drill Manual de usuario

Greenlee HID6506 - 42309 Rotary Impact Drill Manuel utilisateur

Ce manuel convient également à

Greenlee HID6506 - 42309 Rotary Impact Drill Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents