Milwaukee M18 RC Manuel utilisateur

Marque: Milwaukee

Modèle: M18 RC

Taper: Manuel utilisateur

Ce manuel convient également à

6502627

OPERATOR’S MANUAL

M18™ Radio/Charger

Cat. No.

M18 RC

To reduce the risk of injury, user must read and understand operator's manual.

WARNING

CHARGER SAFETY

IMPORTANT SAFETY INSTRUCTIONS

29) SAVE THESE INSTRUCTIONS - THIS OPER-

ATOR’S MANUAL CONTAINS IMPORTANT

SAFETY AND OPERATING INSTRUCTIONS

FOR MILWAUKEE

LI-ION M18™ RADIO

CHARGER.

30) BEFORE USING, READ THIS OPERATOR’S

MANUAL, YOUR BATTERY PACK OPERA-

TOR’S MANUAL, AND ALL LABELS ON THE

BATTERY PACK AND RADIO CHARGER.

31) CAUTION - TO REDUCE THE RISK OF

INJURY, CHARGE MILWAUKEE

LITHIUM-

ION PACKS ONLY IN THEIR MILWAUKEE

LITHIUM-ION CHARGER. Other types of char-

gers may cause personal injury or damage.

Battery pack and charger are not compatible

with V™-technology or NiCd systems. Do not

wire a battery pack to a power supply plug

or car cigarette lighter. Battery packs will be

permanently disabled or damaged.

RADIO SAFETY

WARNING

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. In-

stall in accordance with the manufacturer’s

instructions.

8) Do not install near any heat sources such

as radiators, heat registers, stoves, or other

apparatus (including amplifiers that produce

heat.)

10) Protect the power cord from being walked on

or pinched particularly at plugs,convenience

receptacles,and the point where they exit

from the apparatus.

11) Only use attachments/accessories specified

by the manufacturer.

12) Use only with the cart, stand, tripod, bracket,

or table speci fied by the manufacturer, or

sold with the apparatus. When a cart is

used, use caution when moving the cart/

apparatus combination to avoid injury from

tip-over.

13) Unplu

g this apparatus during lightning

storms or when unused for long periods of

time.

14) Refer all servicing to qualified service per-

sonnel. Servicing is required when the ap-

paratus has been damaged in any way,such

as power-supply cord or plug is damaged,

liquid has been spilled or objects have fallen

into the apparatus, the apparatus has been

exposed to rain or moisture, does not oper-

ate normally, or has been dropped.

15) WARNING To reduce the risk of fire or elec-

tric shock, do not expose this apparatus to

rain or moisture.

16) Only plug power supply into readily ac-

cessible outlet to allow the appliance to be

unplugged quickly.

17) Only operate this apparatus in a well-

ventilated area.

18) A battery operated radio with integral bat-

teries or a separate battery pack must be

recharged only with the specified charger

for the battery. A charger that may be suitable

for one type of battery may create a risk of re

when used with another battery.

19) Use battery operated radio only with specifi -

cally designated battery packs. Use of any

other batteries may create a risk of

re.

20) When battery pack is not in use, keep it away

from other metal objects like: paper clips,

coins, keys, nails, screws, or other small

metal objects that can make a connection

from one terminal to another. Shorting the

battery terminals together may cause sparks,

burns, or a re.

21) Avoid body contact with grounded surfaces

such as pipes, radiators, ranges and refrig-

erators. There is an increased risk of electric

shock if your body is grounded.

22) Do not use any adaptor plugs.

23) When operating a radio outside, use an

outdoor extension cord marked “W-A” or

“W”. These cords are rated for outdoor use

and reduce the risk of electric shock.

24) Never disassemble the radio or try to do any

rewiring on the radio's electrical system.

25) Do not expose this apparatus to dripping

and splashing, or place objects filled with

liquids on this unit.

26) Maintain labels and nameplates. These carry

important information. If unreadable or missing,

contact a MILWAUKEE service facility for a free

replacement.

27)

contact your local authorised MILWAUKEE

dealer or service centre.

The apparatus shall not be exposed to

dripping or splashing and that no objects filled

with liquids, such as vases, shall be placed on

the apparatus.

28)

Do not defeat the safety purpose of the

polarised or grounding-type plug. A

polarised plug has two blades with one

wider than the other. A grounding type plug

has two blades and a third grounding

prong. The wide blade or the third prong are

provided for your safety. If the provided

plug does not fit into your outlet, consult an

electrician for replacement of the obsolete

outlet.

This radio charger is designed to be

or AC generator. The radio can also be

powered using a MILWAUKEE

M18™ Li-Ion

battery pack. Radio charger must be plugged

into an appropriate receptacle. Do not attempt

to use with any other voltage or power supply.

Cat. No.

AC Input DC Output *

Volts Amps Volts Amps

M18 RC 1.0 18 3.5

* Charges MILWAUKEE

M18™ Li-Ion battery

SPECIFICATIONS

32) CHARGE IN A WELL VENTILATED AREA.

Do not block charger vents. Keep them clear to

allow proper ventilation. Do not allow smoking

or open ames near a charging battery pack.

Vented gases may explode.

33) MAINTAIN CHARGER CORD. When unplug-

ging charger, pull plug rather than cord to

reduce the risk of damage to the electrical plug

and cord. Never carry charger by its cord. Keep

cord from heat, oil and sharp edges. Make

sure cord will not be stepped on, tripped over

or subjected to damage or stress. Do not use

charger with damaged cord or plug. Have a

damaged charger replaced immediately.

34) DO NOT USE AN EXTENSION CORD UN-

LESS IT IS ABSOLUTELY NECESSARY.

Using the wrong, damaged or improperly wired

extension cord could result in the risk of re and

electrical shock. If an extension cord must be

used, plug the charger into a properly wired 16

gauge or larger extension cord with pins that

are the same number, size and shape as the

pins on the charger. Make sure that the exten-

sion cord is in good electrical condition.

35) USE ONLY RECOMMENDED ATTACH-

MENTS. Use of an attachment not recom-

mended or sold by the battery charger or

battery pack manufacturer may result in a risk

re, electric shock or personal injury.

36) UNPLUG CHARGER when not in use. Remove

battery packs from unplugged chargers.

37)

38) STORE YOUR BATTERY PACK AND CHAR-

GER in a cool, dry place. Do not store battery

pack where temperatures may exceed 120°F

(50°C) such as in direct sunlight, a vehicle or

metal building during the summer.

SYMBOLOGY

Volts

Direct Current

Alternating Current

Amps

Hertz

Double Insulated

Presence of important operating

instructions.

Caution. Risk of electric shock.

•

Connect the equipment into an outlet on a circuit

different from that to which the receiver is con-

nected.

• Consult the dealer or an experienced radio/TV

technician for help.

220-240V

(120

31) AVOID DANGEROUS ENVIRONMENTS. Do

not charge battery pack in rain, snow, damp or

wet locations. Do not use battery pack or charger

in the presence of explosive atmospheres (gas-

eous fumes, dust or ammable materials) be-

cause sparks may be generated when inserting

or removing battery pack, possibly causing re.

This appliance is not intended for use by

persons (including children) with reduced

physical, sensory or mental capabilities, or

lack of experience and knowledge, unless they

have been given supervision or instruction

concerning use of the appliance by a person

responsible for their safety. Children should be

supervised to ensure that they do not play with

the appliance.

If the supply cord is damaged, it must be

replaced by the manufacturer, its service agent

or similarly qualified persons in order to avoid

a hazard.

39)

40)

Regulatory Compliance Mark

41) Danger of explosion if battery is incorrectly

replaced. Replace only with the same or equiva-

lent type.

42) Batteries (battery pack or batteries installed)

shall not be exposed to excessive heat such as

sunshine, fire or the like.

43) The MAINS plug or an appliance coupler is

used as the disconnect device, the disconnect

device shall remain readily operable.

M18B, M18B2, M18BX, M18B4, M18B5,M18B6

and M18B9

TO REDUCE THE RISK OF ELECTRIC

SHOCK, always unplug charger before

cleaning or maintenance. Use a Residual

Current Device (RCD) to reduce shock

hazards.

Read operator's manual

FUNCTIONAL DESCRIPTION

1. Auxiliary compartment latch

2. Display

3. On/Off/Volume control

4. PRESET button

5. MODE button

6. Bluetooth button

7. Play/Pause button

8. EQ button

9. CLOCK button

10. Seek/adjust buttons

11. Charger indicators*

12. Antenna

13. Bottle opener

14. Battery bay

15. Charging contacts

16. Battery bay cover

17. Nameplate (on bottom)

18. Cord

19. Cord wrap

20. Auxiliary compartment

21. Backup-battery

compartment

(not shown)

22. Stereo AUX jack

23. USB power outlet

* Charger Indicators

When a battery pack is inserted into the charger,

the LEDs will indicate the following:

Continuous red: Charging

Continuous green light: Charging is complete

Flashing red: Battery is too hot/cold

Charging will begin when battery reaches

correct charging temperature

Flashing red/green: Damaged or faulty battery

pack

1817

RADIO ASSEMBLY

WARNING Recharge only with the

charger speciﬁ ed for the battery. For speciﬁ c

charging instructions, read the operator’s

manual supplied with your charger and battery.

Inserting/Removing Battery Pack

1. Open the battery bay cover.

2. To insert the battery pack, slide it into the

battery bay.

3. To remove the battery pack, pull the battery

pack off of the bay.

4. Always close the battery bay cover when the

bay is not in use.

Low Battery Indicator

When the radio is powered by a battery pack and

its charge falls below 10%, the low battery indicator

is displayed.

Battery Pack Protection

To protect the life of the battery pack, the radio

will shut off when the battery’s charge becomes

too low. If this happens, plug radio charger into a

120V outlet and charge the battery pack according

Charger Operation.

Installing an Auxiliary Device

Open the auxiliary compartment to connect an MP3

player, CD player, or other audio device using the

stereo auxiliary jack. Small devices can be stored

in the compartment during use.

USB Power Outlet

This outlet can be used to charge a cell phone,

power an MP3 player or any other device that uses

less than 2.1A of DC electrical current.

NOTE: Any device that uses more than 2.1 A of DC

electrical current will trip a self-resetting overload

and disable the output.

Changing Back-up Batteries

Double insulated tools can use either a two or

three wire extension cord. As the distance from the

supply outlet increases, you must use a heavier

gauge extension cord. Using extension cords with

inadequately sized wire causes a serious drop in

voltage, resulting in loss of power and possible tool

damage. Refer to the table shown to determine the

required minimum wire size.

The smaller the gauge number of the wire, the

greater the capacity of the cord. For example, a 14

gauge cord can carry a higher current than a 16

gauge cord. When using more than one extension

cord to make up the total length, be sure each cord

contains at least the minimum wire size required.

If you are using one extension cord for more than

one tool, add the nameplate amperes and use the

sum to determine the required minimum wire size.

Guidelines for Using Extension Cords

• If you are using an extension cord outdoors,

be sure it is marked with the suf¿ x “W-A” (“W”

in Canada) to indicate that it is acceptable for

outdoor use.

• Be sure your extension cord is properly wired

and in good electrical condition. Always replace

a damaged extension cord or have it repaired by

a quali¿ ed person before using it.

• Protect your extension cords from sharp objects,

excessive heat and damp or wet areas.

• Unplug all cords during lightning storms or when

unused for long periods of time.

EXTENSION CORDS

Recommended Min. Wire Gauge for Extension Cords*

Extension Cord Length

* Based on limiting the line voltage drop to ¿ ve volts at

150% of the rated amperes.

Nameplate

Amperes

0 - 2.0

2.1 - 3.4

3.5 - 5.0

5.1 - 7.0

7.1 - 12.0

12.1 - 16.0

16.1 - 20.0

25'

75'

100'

150'

50'

Power

The MILWAUKEE M18 ™ Radio Charger can be

packs or a standard wall outlet. When plugged into a

wall outlet, the battery bay will charge

MILWAUKEE

M18™ Li-Ion battery packs (see Charger Operation).

WARNING Batteries may leak chemi-

cals or may explode if used incorrectly. The

following care should be taken to prevent

such an incident:

• Make sure the positive (+) and negative (-)

battery terminals are positioned correctly.

• Do not mix new and old batteries together,

or mix different types of batteries.

• Do not try to recharge non-rechargeable

batteries.

If chemicals from the batteries come in

contact with your skin, wash them off imme-

diately with water. If chemicals leak onto the

radio, clean the radio completely.

To hold station presets and clock time when the

battery pack is removed and the radio is unplugged,

2 AAA batteries are required.

1. Remove battery pack and unplug radio.

2. Remove the screw and battery cover.

3. Insert two (2) AAA batteries according to

matching positive (+) and negative (-) marks.

4. Replace the battery cover and screw.

220-240V outlet and charge the battery pack

according to Charger Operation.

Double insulated tools can use three wire

extension cord. As the distance from the supply

outlet increases, you must use a heavier gauge

extension cord. Using extension cords with

inadequately sized wire causes a serious drop in

voltage, resulting in loss of power and possible

tool damage.

Guidelines for Using Extension Cords

• Be sure your extension cord is properly wired

and in good electrical condition. Always replace

a damaged extension cord or have it repaired by

a qualifi ed person before using it.

• Protect your extension cords from sharp objects,

excessive heat and damp or wet areas.

• Unplug all cords during lightning storms or when

unused for long periods of time.

RADIO ASSEMBLY

WARNING Recharge only with the

charger speciﬁ ed for the battery. For speciﬁ c

charging instructions, read the operator’s

manual supplied with your charger and battery.

Power

The MILWAUKEE M18™ Radio Charger can be

packs or a standard wall outlet. When plugged

into a wall outlet, the battery bay will charge

MILWAUKEE M18™ Li-Ion battery packs (see

Charger Operation).

•

If you are using an extension cord outdoors, be

sure to indicate that it is acceptable for outdoor

use.

RADIO OPERATION

WARNING To reduce the risk of ﬁ re

or electric shock, do not expose this radio to

rain or moisture.

WARNING Always remove battery

pack before changing or removing acces-

sories. Only use accessories specifically

recommended for this radio. Others may be

hazardous.

Turning On/Off and Controlling Volume

Plug the cord into an appropriate AC outlet or install

a battery pack.

Press the On/Off/Volume control button to turn

the radio on and off. The radio station (frequency)

is displayed. To display the time, press the CLOCK

button. Volume is restored to the last setting.

NOTE: When the Radio Charger is running on

battery power, the display will dim after 5 minutes

to reduce power use.

Rotate the On/Off/Volume control button to

increase or decrease the volume.

Setting the Clock

1. Press and hold the CLOCK button until the hour

begins to À ash.

2. Use the Ż and Ź buttons to change the hour.

3. Press the CLOCK button again. The minutes

will begin to À ash. Use the Ż and Ź buttons to

change the minutes.

4. Press the CLOCK button again to save.

EQ Adjustment

To manually adjust the Bass/Treble sound, press

the EQ button. Set the bass sound by rotating the

On/Off/Volume control button

. Press the EQ

button again to set the treble sound by rotating the

On/Off/Volume control button .

Selecting Band

Push the MODE button to select Bluetooth, FM,

AM, or AUX.

Tuning and Seeking

Press the Ż and Ź buttons to move up and down

the band. Press, hold, and release the Ż and Ź

buttons to SEEK through the band. When a station

is found, the SEEK will stop.

PRESET Stations

To set the PRESET stations:

1. Tune to desired station.

2. Press and hold the PRESET button until the

PRESET indicator on the display begins to À ash.

3. Use the Ż and

Ź buttons to select the PRESET

location for the station. Five locations (1-5) are

available.

4. Press the PRESET button to save the location.

To tune to a PRESET station:

Press and release the PRESET button to step

through the PRESET stations.

Using the Stereo AUX Jack

1. Open the Auxiliary Compartment

2. Plug the auxiliary device into the Stereo AUX

jack.

3. Use the MODE button to select AUX.

4. Start the auxiliary device.

Using Bluetooth

To enter the Bluetooth mode, press the but-

ton, or press the MODE button to cycle through

to Bluetooth.

Pairing

• If no Bluetooth device is connected, Bluetooth

pairing will begin automatically and the icon

will À ash on the display.

• The radio will continue to search for a signal for

3 minutes.

• To manually pair a device, press and hold blue-

tooth button until the begins to À ash.

• While the is À ashing, select "Milwaukee" on

the Bluetooth capable device.

• Enter PIN "0000".

• Once the device has successfully paired with the

radio, the will be shown on the radio's display.

Connecting

To enter the Bluetooth mode, press the but-

ton, or press the MODE button to cycle through

to Bluetooth.

When the radio locates a paired Bluetooth device,

the will be shown on the radio's display.

If connection is lost between the radio and the

Bluetooth device, the radio will try to reconnect

automatically for up to 3 minutes.

Controlling

When streaming music through to the radio via

a Bluetooth device, use the button to start

and pause the music. Use the Ż and Ź to move

through the tracks.

CHARGER OPERATION

WARNING Charge only MILWAUKEE

M18™ Lithium-Ion battery packs in the

MILWAUKEE

Li-Ion Battery Charger. Other

types of batteries may cause personal injury

and damage. Battery pack and charger are

not compatible with V™-technology or NiCd

systems.

When to Charge MILWAUKEE

Li-Ion Battery

Packs

Remove the battery pack from the tool for

charging when convenient for you and your job.

MILWAUKEE

battery packs do not develop a

"memory" when charged after only a partial dis-

charge. It is not necessary to run down the battery

pack before placing it on the charger.

• Use the Fuel Gauge to determine when to charge

your MILWAUKEE

Li-Ion battery pack.

• You can "Top-Off" your battery pack's charge

before starting a big job or long day of use.

• The only time it is necessary to charge the

MILWAUKEE

Lithium-Ion battery pack is when

the pack has reached the end of its charge. To

signal the end of charge, power to the tool will drop

quickly, allowing you just enough power to ¿ nish

making a cut, drilling a hole, or driving a fastener.

Charge the battery pack as needed.

How to Charge the Battery Pack

Plug the Radio Charger into a 120V outlet. The

battery packs will not charge if the Radio Charger

is not plugged in. Place the battery pack onto the

bay by sliding the pack on from the top of the bay.

The red light will turn on, either À ashing (pack is

too hot or cold) or continuous (pack is charging).

• A fully discharged pack with an internal tempera-

ture between 32°F and 104°F will charge in 30-Min

or 1-Hour, depending on the battery pack.

• Heavily cycled battery packs may take longer to

charge completely.

• The Fuel Gauge lights on the battery pack are

displayed as the pack is being charged, indicating

how fully charged the pack is.

• After charging is complete, the continuous green

light will turn on and the fuel gauge will turn off.

• The charger will keep the battery pack fully

charged if it is left on the charger.

• If the light indicator À ashes red and green, check

that the battery pack is fully seated into the bay.

Remove the pack and reinsert. If the problem

persists, contact a MILWAUKEE service facility.

• If the light indicator does not come on, check

that the battery pack is fully seated into the bay.

Remove the pack and reinsert. If the light indicator

still does not come on, contact a MILWAUKEE

service facility.

Charging a Hot or Cold Battery Pack

The Red À ashing indicator light on the charger indi-

cates that the battery pack temperature is outside

the charging range. Once the pack is within the

acceptable range, normal charging will take place

and the red light will be continuous. Hot or cold

battery packs may take longer to charge.

Li-Ion Charging Status

Battery Pack

Temperature

Red Charger

Indicator Light

Charging Status

Too Hot

Normal Range

Too Cold

Flashing

Continuous

Flashing

Not charging

Normal charging

Not charging

ACCESSORIES

MAINTENANCE

WARNING To reduce the risk of injury,

always unplug your tool before performing

any maintenance. Never disassemble the tool

or try to do any rewiring on the tool’s electrical

system. Contact a MILWAUKEE service facility

for ALL repairs.

WARNING To reduce the risk of injury,

electric shock and damage to the tool, never

immerse your tool in liquid or allow a liquid

to ﬂ ow inside the tool.

Maintenance and Storage

Store your charger in a cool, dry place.

As a general practice, it is best to unplug battery

chargers and remove battery packs when not in

use. No battery pack damage will occur, however,

if the charger and battery pack are left plugged in.

Cleaning

Clean out dust and debris from charger vents and

electrical contacts by blowing with compressed air.

Use only mild soap and a damp cloth to clean the

battery pack and charger, keeping away from all elec-

trical contacts. Certain cleaning agents and solvents

are harmful to plastics and other insulated parts.

Some of these include gasoline, turpentine, lacquer

thinner, paint thinner, chlorinated cleaning solvents,

ammonia and household detergents containing am-

monia. Never use À ammable or combustible solvents

around battery packs, charger, or tools.

Repairs

If your tool is damaged, return the entire tool to the

nearest service center.

If the supply cord is damaged, it must be replaced

by the manufacturer, its service agent or similarly

qualiﬁ ed persons in order to avoid a hazard.

WARNING To reduce the risk of injury,

always unplug the tool before attaching or

removing accessories. Use only speciﬁ cally

recommended accessories. Others may be

hazardous.

Plug the Radio Charger into a 220-240V outlet. The

0˚C

40˚C

system. Contact your local authorised

MILWAUKEE

dealer or service centre.

• If the light indicator flashes red and green,

check that the battery pack is fully seated into

the bay. Remove the pack and reinsert. If the

problem persists, contact your local authorised

MILWAUKEE

dealer or service centre.

• If the light indicator does not come on, check

that the battery pack is fully seated into the

bay. Remove the pack and reinsert. If the light

indicator still does not come on, contact your

local authorised MILWAUKEE

dealer or service

centre.

For a complete listing of accessories refer to your

MILWAUKEE

Electric Tool catalogue or go on-

line to milwaukeetools.com.au or milwaukeetools.

co.nz. To obtain a catalogue, contact your your

local authorised MILWAUKEE

dealer or service

centre.

For a list of MILWAUKEE

dealers, guarantee or service agents please contact MILWAUKEE

Customer Service or visit our website.

(Australia Toll Free Telephone Number 1300 645 928)

(New Zealand Toll Free Telephone Number 0800 279 624)

or visit www.milwaukeetools.com.au / www.milwaukeetools.co.nz.

Milwaukee Electric Tool Corporation

13135 West Lisbon Road, Brookfield, Wisconsin U.S.A. 53005

Milwaukee Electric Tool Corporation (Australia)

Techtronic Industries (Australia) Pty. Ltd.

Rowville, Victoria, Australia, 3178

Milwaukee Electric Tool Corporation (New Zealand)

Techtronic Industries (New Zealand) Pty. Ltd.

Mangere, Auckland, New Zealand, 2022

Professionally made in China for Milwaukee Electric Tool Corporation

WARRANTY - AUSTRALIA and NEW ZEALAND

SERVICE - AUSTRALIA and NEW ZEALAND

MILWAUKEE

prides itself in producing a premium quality product that is Nothing But Heavy Duty

Your satisfaction with our products is very important to us! If you encounter any problems with the

operation of this tool, please contact your authorised MILWAUKEE

dealer.

Please refer to Australian and New Zealand warranty supplied with tool. This warranty applies only to

product sold in Australia and New Zealand.

Milwaukee M18 RC Manuel utilisateur

Marque: Milwaukee

Modèle: M18 RC

Taper: Manuel utilisateur

Ce manuel convient également à

6502627

Télécharger le PDF

rapport

dans d''autres langues

English: Milwaukee M18 RC User manual

Milwaukee M18 RC Manuel utilisateur

Ce manuel convient également à

Milwaukee M18 RC Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents