IKEA ID5HHEXVQ00 Le manuel du propriétaire

Marque: IKEA

Modèle: ID5HHEXVQ00

Catégorie: Frigos

Taper: Le manuel du propriétaire

Ce manuel convient également à

THANK YOU for purchasing this high-quality product. If you should experience a problem not covered in TROUBLESHOOTING,

please visit www.whirlpool.com for additional information. If you still need assistance, call us at 1-866-664-2449.

You will need your model and serial number, located on the inside wall of the refrigerator compartment.

Para obtener acceso a "lnstrucciones para el usuario del refrigerador" en espa_ol, o paraobtener informaci6n adicional acerca de

su producto, visite: www.whirlpool.com.

Necesitara su nOmerode modelo y de serie, ubicado en el interior del compartimiento del refrigerador.

TableofContents/Tabledes mati6res

REFRIGERATOR SAFETY ..................................................................... 1

INSTALLATION INSTRUCTIONS ......................................................... 2

REFRIGERATOR USE ........................................................................... 5

REFRIGERATOR CARE ......................................................................... 8

TROUBLESHOOTING ............................................................................ 9

ACCESSORIES .................................................................................... 11

WATER FILTER CERTIFICATIONS .................................................... 11

PERFORMANCE DATA SHEET .......................................................... 12

WAR RAN TY .......................................................................................... 13

SI_CURITI_ DU RI_FRIGI_RATEUR ..................................................... 14

INSTRUCTIONS D'INSTALLATION ................................................... 15

UTILISATION DU RI=FRIGI=RATEUR ................................................. 18

ENTRETIEN DU RI=FRIGI=RATEUR ................................................... 21

DI_PANNAGE ........................................................................................ 22

ACCESSOIRES .................................................................................... 25

FEUlLLE DE DONNI_ES SUR LA PERFORMANCE .......................... 26

GARANTIE ............................................................................................ 27

REFRIGERATORSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

W10254643B

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

• Plug into a grounded 3 prong outlet.

• Do not remove ground prong.

• Do not use an adapter.

• Do not use an extension cord.

• Disconnect power before servicing.

• Replace all parts and panels before operating.

• Remove doors from your old refrigerator.

• Use nonflammable cleaner.

• Keep flammable materials and vapors, such as gasoline,

away from refrigerator.

• Use two or more people to move and install refrigerator.

• Disconnect power before installing ice maker (on ice maker

kit ready models only).

• Use a sturdy glass when dispensing ice (on some models).

SAVE THESE INSTRUCTIONS

Proper Disposal of Your Old Refrigerator

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can result in death or brain damage.

IMPORTANT: Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are still dangerous

- even if they will sit for "just a few days." Ifyou are getting rid of

your old refrigerator, please follow these instructions to help

prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer:

• Takeoff the doors.

• Leave the shelves in place so that children may not easily

climb inside.

INSTALLATIONINSTRUCTIONS

Excessive Weight Hazard

Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other injury.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator for

cleaning or service, be sure to cover the floor with

cardboard or hardboard to avoid floor damage. Always pull

the refrigerator straight out when moving it. Do not wiggle or

"walk" the refrigerator when trying to move it, as floor

damage could occur.

Remove packaging materials. Do not use sharp instruments,

rubbing alcohol, flammable fluids, or abrasive cleaners to remove

tape or glue. These products can damage the surface of your

refrigerator. For more information, see "Refrigerator Safety."

Important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

Tempered glass is designed to shatter into many small,

pebble-size pieces. This is normal. Glass shelves and covers

are heavy. Use both hands when removing them to avoid

dropping.

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

To ensure proper ventilation for your refrigerator, allow for V2"

(1.25 cm) space on each side and at the top. When installing your

refrigerator next to a fixed wall, leave 2" (5.08 cm) minimum on

each side (depending on your model) to allow for the door to

swing open. If your refrigerator has an ice maker, allow extra

space at the back for the water line connections.

-_ /41 'J

1/2" (1.25 cm)//t

,, - if!

2" (5.08 cm)

NOTES:

• It is recommended that you do not install the refrigerator near

an oven, radiator, or other heat source. Do not install in a

location where the temperature will fall below 55°F (13°C).

Normal minimum cabinet cut-out width required for product

installation is 36" (91.44 cm). However, if the product is placed

against an extended wall and the ability to remove the crisper

pans is desired, an additional 18" (45.72 cm) of cabinet width

is required, so a total cabinet opening width of 54"

(137.16 cm)is recommended.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Before you move your refrigerator into its final location, it is

important to make sure you have the proper electrical connection.

Recommended Grounding Method

A 115 Volt, 60 Hz., AC only, 15- or 20-amp fused, grounded

electrical supply is required. It is recommended that a separate

circuit serving only your refrigerator be provided. Use an outlet

that cannot be turned off by a switch. Do not use an

extension cord.

NOTE: Before performing any type of installation, cleaning, or

removing a light bulb, turn the control (Thermostat, Refrigerator or

Freezer Control depending on the model) to OFF and then

disconnect the refrigerator from the electrical source. When you

are finished, reconnect the refrigerator to the electrical source and

reset the control (Thermostat, Refrigerator or Freezer Control

depending on the model) to the desired setting. See "Using the

Controls."

!_e[ e _i' "'pp/y Ii®qui[®me ' Is

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

TOOLS NEEDED:

• Flat-blade screwdriver • V4"Nut driver

• 7/_6"and V2"Open-end or two • V4"Drill bit

adjustable wrenches • Cordless drill

NOTE: Your refrigerator dealer has a kit available with a V4"

(6.35 mm) saddle-type shutoff valve, a union, and copper tubing.

Before purchasing, make sure a saddle-type valve complies with

your local plumbing codes. Do not use a piercing-type or 346"

(4.76 mm) saddle valve which reduces water flow and clogs more

easily.

IMPORTANT:

• All installations must meet local plumbing code requirements.

• Use copper tubing and check for leaks. Install copper tubing

only in areas where the household temperatures will remain

above freezing.

Water Pressure

A cold water supply with water pressure of between 30 and

120 psi (207 and 827 kPa)is required to operate the water

dispenser and ice maker. Ifyou have questions about your water

pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the

refrigerator needs to be between 30 and 120 psi (207 and

827 kPa).

If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 to 414 kPa):

• Check to see whether the sediment filter in the reverse

osmosis system is blocked. Replace the filter if necessary.

• Allow the storage tank on the reverse osmosis system to refill

after heavy usage.

If your refrigerator has a water filter, it may further reduce the

water pressure when used in conjunction with a reverse

osmosis system. Remove the water filter. See "Water Filtration

System."

If you have questions about your water pressure, call a licensed,

qualified plumber.

Read all directions before you begin.

IMPORTANT: If you turn the refrigerator on before the water line is

connected, turn the ice maker OFF.

Connect to Water Line

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

3. Locate a 1/2"(12.70 mm) to 11¼"(3.18 cm) vertical cold water

pipe near the refrigerator.

IMPORTANT:

• Make sure it is a cold water pipe.

• Horizontal pipe will work, but drill on the top side of the

pipe, not the bottom. This will help keep water away from

the drill and normal sediment from collecting in the valve.

Determine the length of copper tubing you need. Measure

from the connection on the lower rear corner of refrigerator to

the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use 1/4"

(6.35 mm) O.D. (outside diameter) copper tubing. Be sure both

ends of copper tubing are cut square.

Using a cordless drill, drill a 1/4"(6.35 mm) hole in the cold

water pipe you have selected.

G _ _ ..............A ..............C

A. Cold waterpipe

B. Pipe clamp

C. Copper tubing

D. Compression nut

E. Compression sleeve

F. Shutoff valve

G. Packing nut

6. Fasten the shutoff valve to the cold water pipe with the pipe

clamp. Be sure the outlet end is solidly in the 1/4"(6.35 mm)

drilled hole in the water pipe and that the washer is under the

pipe clamp. Tighten the packing nut. Tighten the pipe clamp

screws slowly and evenly so the washer makes a watertight

seal. Do not overtighten or you may crush the copper tubing.

7. Slip the compression sleeve and compression nut on the

copper tubing as shown. Insert the end of the tubing into the

outlet end squarely as far as it will go. Screw the compression

nut onto outlet end with adjustable wrench. Do not

overtighten.

8. Place the free end of the tubing in a container or sink, and turn

ON the main water supply. Flush the tubing until water is clear.

Turn OFF the shutoff valve on the water pipe. Coil the copper

tubing.

Connect to Refrigerator

Style 1

1. Unplug refrigerator or disconnect power.

2. Attach the copper tube to the valve inlet using a compression

nut and sleeve as shown. Tighten the compression nut. Do not

overtighten.

3. Use the tube clamp on the back of the refrigerator to secure

the tubing to the refrigerator as shown. This will help avoid

damage to the tubing when the refrigerator is pushed back

against the wall.

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any connections (including

connections at the valve) or nuts that leak.

A. Tube clamp

B. Tube clamp screw

C. Copper tubing

D. Compression nut

E. Valve inlet

The ice maker is equipped with a built-in water strainer. If your

water conditions require a second water strainer, install it in

the 1/4"(6.35 mm) water line at either tube connection. Obtain

a water strainer from your nearest appliance dealer.

Style 2

1. Unplug refrigerator or disconnect power.

2. Remove and discard the black nylon plug from the gray water

tube on the rear of the refrigerator.

3. If the gray water tube supplied with the refrigerator is not long

enough, a V4"x 1/4"(6.35 mm x 6.35 mm) coupling is needed in

order to connect the water tubing to an existing household

water line. Thread the provided nut onto the coupling on the

end of the copper tubing.

NOTE:Tightenthenutbyhand.Thentightenitwithawrench

twomoreturns.Donotovertighten.

2. Flushthewatersystem.See"PreparetheWaterSystem"or

"WaterandIceDispensers."

NOTE:Allow24hourstoproducethefirstbatchofice.Allow

3daystocompletelyfillicecontainer.

REFRIGERATORUSE

A B C D E F G

A. Refrigerator water tubing

B. Nut (provided)

C. Bulb

D. Coupfing (purchased)

E. Ferrule (purchased)

F Nut (purchased)

G. Household water line

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any nuts or connections (including

connections at the valve) that leak.

Style 3

1. Unplug refrigerator or disconnect power.

2. Remove and discard the black nylon plug from the gray water

tube on the rear of the refrigerator.

3. Thread the provided nut onto the water valve as shown.

NOTE: Tighten the nut by hand. Then tighten it with a wrench

two more turns. Do not overtighten.

t/ II

A. Bulb

B. Nut (provided)

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any nuts or connections (including

connections at the valve) that leak.

Complete the Installation

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

eCon't s

For your convenience, your refrigerator controls are preset at the

factory. When you first install your refrigerator, make sure that the

controls are still preset. The Refrigerator Control and the Freezer

Control should both be set to the "mid-settings."

FREEZER REFRIGERATOR

• o

2 4

COLD l@s COLDER 2@t.

COLD 1 s COLDER

IM PORTANT:

Your product will not cool when the REFRIGERATOR Control

is set to OFE

The Refrigerator Control adjusts the refrigerator compartment

temperature. The Freezer Control adjusts the freezer

compartment temperature. Settings to the left of the mid-

setting make the temperature less cold. Settings to the right of

the mid-setting make the temperature colder.

Wait 24 hours before you put food into the refrigerator. If you

add food before the refrigerator has cooled completely, your

food may spoil.

NOTE: Adjusting the Refrigerator and Freezer Controls to a higher

(colder) than recommended setting will not cool the

compartments any faster.

Adjusting Controls

Give the refrigerator time to cool down completely before adding

food. It is best to wait 24 hours before you put food into the

refrigerator. The settings indicated in the previous section should

be correct for normal household refrigerator usage. The controls

are set correctly when milk or juice is as cold as you like and when

ice cream is firm.

Turn the control right (clockwise) to make the compartment colder.

Turn the control left (counterclockwise) to make it less cold. To

turn the cooling system off, turn the Refrigerator Control

counterclockwise until it reaches the OFF position.

If you need to adjust temperatures in the refrigerator or freezer,

use the settings listed in the chart below as a guide. Wait at least

24 hours between adjustments.

CONDITION/REASON: ADJUSTMENT:

REFRIGERATOR too warm REFRIGERATOR Control

one setting higher

FREEZER too warm/ FREEZER Control

too little ice one setting higher

REFRIGERATOR too cold REFRIGERATOR Control

one setting lower

FREEZER too cold FREEZER Control

one setting lower

1. Plug into a grounded 3 prong outlet.

Thecontrolcanbeadjustedtoproperlychillmeatsorvegetables.

Theairinsidethepaniscooledtoavoid"spot"freezingandcan

besettokeepmeatsattheNationalLivestockandMeatBoard

recommendedstoragetemperaturesof28°to32°F(-2°to0°C).

Theconvertiblevegetable/meatdrawercontrolcomespresetat

thelowestmeatsetting.

To store meat:

Set the control to one of the three MEAT settings to store meat at

its optimal storage temperature.

To store vegetables:

Set the control to VEG to store vegetables at their optimal storage

temperatures.

NOTE: If food starts to freeze, move the control to the left (less

cold). Remember to wait 24 hours between adjustments.

some modes

You can control the amount of humidity in the moisture-sealed

crisper. Adjust the control to any setting between LOW and HIGH.

LOW (open) for best storage of fruits and vegetables with skins.

HIGH (closed) for best storage of fresh, leafy vegetables.

(on so "_'e re(des

Depending on your model, you may have one or more of the

following options: the ability to select either crushed or cubed ice,

chilled water, a special light that turns on when you use the

dispenser, or a lock option to avoid unintentional dispensing.

NOTES:

• The dispensing system will not operate when the freezer door

is open.

After connecting the refrigerator to a water source, flush the

water system. Use a sturdy container to depress and hold the

water dispenser lever for 5 seconds, then release it for

5 seconds. Repeat until water begins to flow. Once water

begins to flow, continue depressing and releasing the

dispenser lever (5 seconds on, 5 seconds off) for an additional

5 minutes. This will flush air from the filter and water

dispensing system. Additional flushing may be required in

some households. As air is cleared from the system, water

may spurt out of the dispenser.

On some models: Allow 24 hours for the refrigerator to cool

down and chill water.

• Allow 24 hours to produce the first batch of ice. Discard the

first three batches of ice produced.

Cool air from the freezer is directed to the refrigerator door bin

directly beneath the vents.

NOTE: The dairy compartment and can rack are not associated

with the Chilled Door Bin feature.

Chilled Door Bin Control

The chilled door bin control is located on the left-hand side of the

refrigerator compartment.

A .....

A. Chilled door bin control

Slide the door chill control to the left to reduce the flow of cold

air to the bin and make it less cold.

Slide the door chill control to the right to increase the flow of

cold air to the bin and make it colder.

The Water Dispenser

IMPORTANT: Dispense enough water every week to maintain a

fresh supply.

To Dispense Water:

1. Press a sturdy glass against the water dispenser lever.

2. Remove the glass to stop dispensing.

The Ice Dispenser

The dispensing system will not operate when the freezer door is

open. Ice dispenses from the ice maker storage bin in the freezer

when the dispenser lever is pressed.

NOTE: Some models dispense both cubed and crushed ice.

Before dispensing ice, select which type of ice you prefer.

For crushed ice, cubes are crushed before being dispensed. This

may cause a slight delay when dispensing crushed ice. Noise

from the ice crusher is normal, and pieces of ice may vary in size.

When changing from crushed to cubed, a few ounces of crushed

ice will be dispensed along with the first cubes.

To Dispense Ice:

1. Press the button to select the desired type of ice.

Cut Hazard

Use a sturdy glass when dispensing ice.

Failure to do so can result in cuts.

Press a sturdy glass against the ice dispenser lever. Hold the

glass close to the dispenser opening so ice does not fall

outside of the glass.

IMPORTANT: You do not need to apply a lot of pressure to the

lever in order to activate the ice dispenser. Pressing hard will

not make the ice dispense faster or in greater quantities.

3. Remove the glass to stop dispensing.

The Dispenser Light

Style 1

The dispenser light can be turned on by pressing the ON button.

The dispenser lights are LEDs which should not need to be

changed. See "Troubleshooting" for more information.

Style 2

When you use the dispenser, the lever will automatically turn the

light on. If you want the light to be on continuously, you may

choose either ON or NIGHT LIGHT.

ON: Press the LIGHT button to turn on the dispenser light.

NIGHT LIGHT: Press the LIGHT button a second time to select

the Night Light. The dispenser light will automatically adjust to

become brighter as the room brightens, dimmer as the room

darkens.

OFF: Press the LIGHT button a third time to turn off the dispenser

light.

The dispenser lights are LEDs which should not need to be

changed. If it appears that your dispenser lights are not working,

be sure that the light sensor is not blocked (in Night Light mode).

See "Troubleshooting" for more information.

The Dispenser Lock (on some models)

The dispenser can be turned off for easy cleaning or to avoid

unintentional dispensing by small children and pets.

NOTE: The lock feature does not shut off power to the product, to

the ice maker, or to the dispenser light. It simply deactivates the

dispenser levers. The ice and water dispensers will not work.

Style 1: Press the LOCK button to lock the dispenser. Press the

UNLOCK button to unlock the dispenser.

Style 2: Press and hold the LOCK OUT button to lock the

dispenser. Press and hold the LOCK OUT button a second time to

unlock the dispenser.

ce v@H sn S o ege Blrs

Turning the Ice Maker On/Off

• To turn ON the ice maker, simply lower the wire shutoff arm.

• To manually turn off the ice maker, lift the wire shutoff arm to

the OFF (arm up) position and listen for the click. Ice can still

be dispensed, but no more can be made.

NOTE: Your ice maker has an automatic shutoff. As ice is made,

the ice cubes will fill the ice storage bin, and the ice cubes will

raise the wire shutoff arm to the OFF (arm up) position. Do not

force the wire shutoff arm up or down.

REMEMBER:

• Allow 24 hours to produce the first batch of ice. Discard the

first three batches of ice produced.

The quality of your ice will be only as good as the quality of the

water supplied to your ice maker. Avoid connecting the ice

maker to a softened water supply. Water softener chemicals

(such as salt) can damage parts of the ice maker and lead to

poor quality ice. If asoftened water supply cannot be avoided,

make sure the water softener is operating properly and is well

maintained.

Do not use anything sharp to break up the ice in the storage

bin. This can cause damage to the ice container and the

dispenser mechanism.

Do not store anything on top of or in the ice maker or storage

bin.

Removing and Replacing Ice Storage Bin

1. Pull the covering panel up from the bottom and then slide it

back toward the rear.

2. Lift the wire shutoff arm so it clicks into the OFF (up) position.

3. Lift up the front of the storage bin and pull it out.

Replace the bin by pushing it in all the way or the dispenser

will not work.

To restart ice production, push the wire shutoff arm down to

the ON position. Make sure the door is closed tightly.

,.,, F ffc4on System

Do not use with water that is microbiologically unsafe or of

unknown quality without adequate disinfection before or

after the system.

Water Filter Status Light (on some models)

The water filter status light will help you know when to change

your water filter. The light will change from green to yellow. This

tells you that it is almost time to change the filter. It is

recommended that you replace the water filter when the status

light changes to red OR water flow to your water dispenser or ice

maker decreases noticeably. The filter should be replaced at least

every 6 months depending on your water quality and usage.

After changing the water filter, reset the water filter status light.

The status light will change from red to green when the system is

reset.

Non-Indicator Water Filter (on some models)

If your refrigerator does not have the water filter status light, you

should change the water filter cartridge at least every 6 months

depending on your water quality and usage. If the water flow to

the water dispenser or ice maker decreases noticeably before

6 months have passed, replace the water filter more often.

Using the Dispenser Without the Water Filter

You can run the dispenser without a water filter. Your water will not

be filtered.

1. Remove the water filter.

2. Slide the cap off the end of the filter and replace the cap in the

base grille.

IMPORTANT: Do not discard the cap. It is part of your

refrigerator. Keep the cap to use with the replacement filter.

REFRIGERATORCARE

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

Both the refrigerator and freezer sections defrost automatically.

However, clean both sections about once a month to avoid

buildup of odors. Wipe up spills immediately.

IMPORTANT: Because air circulates between both sections, any

odors formed in one section will transfer to the other. You must

thoroughly clean both sections to eliminate odors. To avoid odor

transfer and drying out of food, wrap or cover foods tightly.

To Clean Your Refrigerator:

NOTE: Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, flammable fluids, cleaning waxes,

concentrated detergents, bleaches or cleansers containing

petroleum products on plastic parts, interior and door liners or

gaskets. Do not use paper towels, scouring pads, or other harsh

cleaning tools.

1. Unplug refrigerator or disconnect power.

2. Hand wash, rinse, and dry removable parts and interior

surfaces thoroughly. Use a clean sponge or soft cloth and a

mild detergent in warm water.

3. Wash stainless steel and painted metal exteriors with a clean

sponge or soft cloth and a mild detergent in warm water.

On some models, wash glass door panels with a clean

sponge or soft cloth and a mild detergent in warm water.

NOTES:

Do not hit the glass with pots, pans, furniture, toys, or

other objects. Scratching, hitting, jarring or stressing the

glass may weaken its structure, causing an increased risk

of breakage at a later date.

• Do not close the doors until all shelves, drawers and bins

are in place.

There is no need for routine condenser cleaning in normal

home operating environments. If the environment is

particularly greasy or dusty, or there is significant pet traffic in

the home, the condenser should be cleaned every 2 to

3 months to ensure maximum efficiency.

If you need to clean the condenser:

• Remove the base grille.

• Use a vacuum cleaner with asoft brush to clean the grille,

the open areas behind the grille and the front surface area

of the condenser.

• Replace the base grille when finished.

Plug in refrigerator or reconnect power.

NOTE: Not all bulbs will fit your refrigerator. Be sure to replace the

bulb with one of the same size, shape and wattage. On some

models, the dispenser light requires a heavy duty 1O-watt bulb. All

other lights require a 40-watt bulb. Replacement bulbs are

available from your dealer.

1. Unplug refrigerator or disconnect power.

2. Remove light shield when applicable.

NOTE: To clean the light shield, wash it with warm water and

liquid detergent. Rinse and dry the shield well.

3. Remove light bulb and replace with one of the same size,

shape and wattage.

4. Replace light shield when applicable.

5. Plug in refrigerator or reconnect power.

TROUBLESHOOTING

Try the solutions suggested here first in order to avoid the cost of an unnecessary service call.

The refrigerator will not operate

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Power cord unplugged? Plug into a grounded 3 prong outlet.

Is outlet working? Plug in a lamp to see ifthe outlet is

working.

Household fuse blown or circuit breaker tripped? Replace

the fuse or reset the circuit breaker. If the problem continues,

call an electrician.

• Are controls on? Make sure the refrigerator controls are on.

See "Using the Controls."

• New installation? Allow 24 hours following installation for the

refrigerator to cool completely.

NOTE: Adjusting the temperature controls to coldest setting will

not cool either compartment more quickly.

The motor seems to run too much

Your new refrigerator may run longer than your old one due to its

high-efficiency compressor and fans. The refrigerator may run

even longer if the room is warm, a large food load is added, doors

are opened often, or if the doors have been left open.

The refrigerator is noisy

Refrigerator noise has been reduced over the years. Due to this

reduction, you may hear intermittent noises from your new

refrigerator that you did not notice from your old model. Below are

listed some normal sounds with an explanation.

• Buzzing - heard when the water valve opens to fill the ice

maker

Pulsating - fans/compressor adjusting to optimize

performance

Rattling - flow of refrigerant, water line, or from items placed

on top of the refrigerator

Sizzling/Gurgling - water dripping on the heater during

defrost cycle

Popping - contraction/expansion of inside walls, especially

during initial cool-down

Water running - may be heard when ice melts during the

defrost cycle and water runs into the drain pan

Creaking/Cracking - occurs as ice is being ejected from the

ice maker mold

The doors will not close completely

• Door blocked open? Move food packages away from door.

• Bin or shelf in the way? Push bin or shelf back in the correct

position.

The doors are difficult to open

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

• Are the gaskets dirty or sticky? Clean gaskets with mild

soap and warm water.

The lights do not work

• Is a light bulb loose in the socket or burned out? See

"Changing the Light Bulbs."

_ _ _,_ _ 7,,¸ _,, _ _

Temperature is too warm

• New installation? Allow 24 hours following installation for the

refrigerator to cool completely.

• Door(s) opened often or left open? Allows warm air to enter

refrigerator. Minimize door openings and keep doors fully

closed.

Large load of food added? Allow several hours for

refrigerator to return to normal temperature.

Controls set correctly for the surrounding conditions?

Adjust the controls a setting colder. Check temperature in

24 hours. See "Using the Controls."

There is interior moisture buildup

NOTE: Some moisture buildup is normal.

• Humid room? Contributes to moisture buildup.

• Door(s) opened often or left open? Allows humid air to enter

refrigerator. Minimize door openings and keep doors fully

closed.

The ice maker is not producing ice or not enough ice

Refrigerator connected to a water supply and the supply

shutoff valve turned on? Connect refrigerator to water

supply and turn water shutoff valve fully open.

Kink in the water source line? A kink in the line can reduce

water flow. Straighten the water source line.

Ice maker turned on? Make sure wire shutoff arm or switch

(depending on model) is in the ON position.

New installation? Wait 24 hours after ice maker installation

for ice production to begin. Wait 72 hours for full ice

production.

Large amount of ice recently removed? Allow 24 hours for

ice maker to produce more ice.

Ice cube jammed in the ice maker ejector arm?

Remove ice from the ejector arm with a plastic utensil.

Reverse osmosis water filtration system connected to

your cold water supply? This can decrease water pressure.

See "Water Supply Requirements."

The ice cubes are hollow or small

NOTE: This is an indication of low water pressure.

• Water shutoff valve not fully open? Turn the water shutoff

valve fully open.

• Kink in the water source line? A kink in the line can reduce

water flow. Straighten the water source line.

• Reverse osmosis water filtration system connected to

your cold water supply? This can decrease water pressure.

See "Water Supply Requirements."

• Questions remain regarding water pressure? Call a

licensed, qualified plumber.

Off-taste, odor or gray color in the ice

New plumbing connections? New plumbing connections

can cause discolored or off-flavored ice.

Ice stored too long? Discard ice. Wash ice bin. Allow

24 hours for ice maker to make new ice.

Odor transfer from food? Use airtight, moisture-proof

packaging to store food.

Are there minerals (such as sulfur) in the water? A water

filter may need to be installed to remove the minerals.

Is there a water filter installed on the refrigerator? Gray or

dark discoloration in ice indicates that the water filtration

system needs additional flushing.

The ice dispenser will not operate properly

• Freezer door closed completely? Close the door firmly. If it

does not close completely, see "The doors will not close

completely."

• Ice bin installed correctly? Be sure the ice bin is firmly in

position.

• New installation? Wait 24 hours after ice maker installation

for ice production to begin. Wait 72 hours for full ice

production.

• Ice stuck in the delivery chute? Use a plastic utensil to clear

the delivery chute.

• Has the wrong ice been added to the bin? Use only cubes

produced by the current ice maker.

• Has the ice melted around the auger (metal spiral) in the

ice bin? Empty the ice container. Use warm water to melt the

ice if necessary.

Cut Hazard

Use a sturdy glass when dispensing ice.

Failure to do so can result in cuts.

Is the ice dispenser stalling while dispensing "crushed"

ice? Change the ice button from "crushed" to "cubed." If

cubed ice dispenses correctly, depress the button for

"crushed" ice and begin dispensing again.

Has the dispenser arm been held in too long? Ice will stop

dispensing when the arm is held in too long. Wait 3 minutes

for dispenser motor to reset before using again.

The water dispenser will not operate properly

• Freezer door closed completely? Close the door firmly. If it

does not close completely, see "The doors will not close

completely."

Refrigerator connected to a water supply and the supply

shutoff valve turned on? Connect refrigerator to water

supply and turn water shutoff valve fully open.

Is the water pressure at least 30 psi (207 kPa)? The water

pressure to the home determines the flow from the dispenser.

See "Water Supply Requirements."

Kink in the home water source line? Straighten the water

source line.

• New installation? Flush and fill the water system.

• Water filter installed on the refrigerator? The filter may be

clogged or incorrectly installed.

• Is a reverse osmosis water filtration system connected to

your cold water supply? See "Water Supply Requirements."

Water is leaking from the dispenser

NOTE: One or two drops of water after dispensing is normal.

• Glass not being held under the dispenser long enough?

Hold the glass under the dispenser for 2 to 3 seconds after

releasing the dispenser lever/pad.

New installation? Flush the water system. See "Prepare the

Water System" or "Water and Ice Dispensers."

Recently changed water filter? Flush the water system. See

"Prepare the Water System" or "Water and Ice Dispensers."

The dispenser water is not cool enough

NOTE: Water from the dispenser is chilled to only 50°F (10°C).

• New installation? Allow 24 hours after installation for the

water supply to cool completely.

Recently dispensed large amount of water? Allow 24 hours

for water supply to cool completely.

Water not been recently dispensed? The first glass of water

may not be cool. Discard the first glass of water.

Refrigerator connected to a cold water pipe? Make sure

the refrigerator is connected to a cold water pipe. See "Water

Supply Requirements."

ACCESSORIES

To order replacement filters, call 1-866-664-2449 and ask for the

part number listed below or contact your authorized Whirlpool

dealer.

Stainless Steel Cleaner and Polish:

Order Part #4396095

Standard Base Filter Cartridge:

Order Part #4396508 (NL240/L400)

WATERFILTER

CERTIFICATIONS

State of California

Deparmlent of Health Services

Water Treatment Device

Certificate Number

03- 1550

Date Issued: January 21,2003

TradcmarldModel Designation Replacement Elements Rated Caa_

Whmpool WF-NL240 NL2_0 240 ga)

Whmpool WF-IA0( 100 400 ga)

Manufacturer: Whirlpool Co_p

1n o r_ a_i_i Radiole_ieal Contaminants

None

)Rated St(_v_ce Flow: 0f gpm

Do not use with _ater that is microbiologicall) unsal_ or of unknown quality, without adequate disinfection

belore or aOer the system.

PERFORMANCEDATASHEET

Base Grille Water Filtration System

Model WF-NL240/NL240 Capacity 240 Gallons (908 Liters)

Model WF-L400/L400 Capacity 400 Gallons (1514 Liters))

(_ System tested and certified by NSF International against

NSF/ANSI Standard 42 for the reduction of Chlorine Taste

and Odor, Particulate Class I1'; and against NSF/ANSI

Standard 53 for the reduct on of Lead.

This system has been tested according to NSF/ANSI Standards 42 and 53 for the reduction of the substances listed below. The

concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the

permissible limit for water leaving the system, as specified in NSF/ANSI Standards 42 and 53..

Substance Reduction NSF Reduction

Aesthetic Effects Requirements

Chlorine Taste/Odor _>50%

Particulate Class I1" _>85%

Contaminant NSF Reduction

Reduction Requirements

Average Influent Challenge Maximum Average Minimum % Average %

Influent Concentration Effluent Effluent Reduction Reduction

1.9 mg/L

833,333/m L

97.4% 97.4%

88.0% 95.1%

2.0 mg/L _+10% 0.05 mg/L 0.05 mg/L

Atparticles/mleast10,000L 100,000/m L** 40,667/m L

Maximum Average

Effluent Effluent

Average Influent Challenge Minimum % Average %

Influent Concentration Reduction Reduction

Lead: @pH6.5 0.01 mg/L 0.15 mg/L***

Lead: @pH8.5 0.01 mg/L 0.15 mg/L***

Test Parameters: pH = 7.5 _+0.5 unless otherwise noted.

Temp. = 63°F (17.2°C).

• It is essential that operational, maintenance, and filter

replacement requirements be carried out for the product to

perform as advertised.

• Model WF-NL240: Change cartridge at least every 6 months.

Use replacement cartridge NL240, part #4396508.

2008 suggested retail price of $32.99 U.S.A./S44.95 Canada.

Prices are subject to change without notice.

Model WF-L400: The filter monitor system measures the

amount of water that passes through the filter and alerts you

to replace the filter. When 90% of the filter's rated life is used,

the filter indicator light changes from green to yellow. When

100% of the filter's rated life is used, the filter indicator light

changes from yellow to red, and it is recommended that you

replace the filter. Use replacement cartridge L400, part

#4396508. 2008 suggested retail price of $32.99 U.S.A./

$44.95 Canada. Prices are subject to change without notice.

The product is for cold water use only.

Do not use with water that is microbiologically unsafe or of

unknown quality without adequate disinfection before or after

the system.

0.15 mg/L + 10% 0.001 mg/L 0.001 mg/L 99.3% 99.3%

0.15 mg/L _+10% 0.003 mg/L 0.001 mg/L 97.9% 99.0%

Flow = 0.5 gpm (1.9 Lpm). Pressure = 60 psig (413.7 kPa).

Note that while the testing was performed under standard

laboratory conditions, actual performance may vary.

Refer to the front cover or "Assistance or Service" section for the

Manufacturer's name, address and telephone number.

Refer to the "Warranty" section for the Manufacturer's limited

warranty.

Application Guidelines/Water Supply Parameters

Water Supply City or Well

Water Pressure 30 - 120 psi (207 - 827 kPa)

Water Temperature 33 ° - 1OO°F (0.6 ° - 37.8°C)

Service Flow Rate 0.5 gpm (1.9 Lpm) @ 60 psi.

* Class II particle size: >1 to <5

** Test requirement is at least 100,000 particles/mL of AC Fine Test Dust.

*** These contaminants are not necessarily in your water supply. Performance may vary based on local water conditions.

® NSF is a registered trademark of NSF International.

IKEAMAJOR APPLIANCE WARRANTY

How long is the IKEA limited warranty valid?

This limited warranty is valid for five years from the date of purchase, when this major appliance is operated and maintained according

to instructions attached to or furnished with the product, unless the appliance is named LAGAN in which case this limited warranty is

valid for one year from the date of purchase. This limited warranty is valid only in the United States or Canada and applies only when the

major appliance is used in the country in which it was purchased. Proof of original purchase date is required to obtain service under this

limited warranty.

Which appliances are not covered by the IKEA five (5) year limited warranty?

For major appliances named "LAGAN," this limited warranty is valid for one year from the date of purchase.

Who will execute the service?

This limited warranty is provided by Whirlpool Corporation or Whirlpool Canada LP (hereafter "Whirlpool"). Service must be provided by

a Whirlpool designated service company.

What does this limited warranty cover?

The limited warranty will pay for factory specified parts and repair labor to correct defects in materials or workmanship that existed

when the major appliance was purchased. The exceptions are specified under the headline "What is not covered under this limited

warranty?".

What will be done to correct the problem?

The designated service company will examine the product and decide, at its sole discretion, if it is covered under this limited warranty.

If considered covered, the designated service company will then repair the defect. Your sole and exclusive remedy under this limited

warranty shall be product repair as provided herein.

What is not covered under this limited warranty?

• Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or

repair house fuses, or to correct house wiring or plumbing.

• Service calls to repair or replace appliance light bulbs, air filters or water filters. Consumable parts are excluded from warranty

coverage.

• Replacement parts or repair labor if this major appliance is used for other than normal, single-family household use or when it is used

in a manner that is inconsistent to published user or operator instructions and/or installation instructions.

• Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in

accordance with electrical or plumbing codes, or use of consumables or cleaning products not approved for use.

• Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage

results from defects in materials or workmanship and is reported within 30 days from the date of purchase.

• Any food loss or medicine loss due to refrigerator or freezer product failures.

• Pick up and delivery. This major appliance is intended to be repaired in your home.

• Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

• Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an

authorized servicer is not available.

The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance with

published installation instructions.

Replacement parts or repair labor on major appliances with original model/serial numbers that have been removed, altered or cannot

be easily determined.

The cost of repair or replacement under these excluded circumstances shall be borne by the customer.

Disclaimer of Implied Warranties

IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR

A PARTICULAR PURPOSE, ARE LIMITED TO FIVE YEARS (ONE YEAR FOR MAJOR APPLIANCES NAMED "LAGAN") OR THE

SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces do not allow limitations on the duration of implied warranties of

merchantability or fitness, so this limitation may not apply to you. This warranty gives you specific legal rights, and you also may have

other rights that vary from state to state or province to province.

Limitation of Remedies; Exclusion of Incidental and Consequential Damages

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.

WHIRLPOOL SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow

the exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This

warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.

How to reach us if you need our service

If outside the 50 United States and Canada, contact your authorized IKEA retailer to determine if another warranty applies.

If you need service, please read the Installation Instructions and/or the "Troubleshooting" section of the Use & Care Guide before

contacting us. If you need additional help, do not hesitate to contact us in the U.S.A. and Canada at 1-866-664-2449.

2/09

NousvousREMERCIONSd'avoiracheteceproduitdehautequalite.Sivousrencontrezunproblemenonmentionne

danslasectionDI_PANNAGE,visiterwww.whirlpool.compourdesinformationssupplementaires.Sivousaveztoujours

besoind'assistance,veuilleznoustel6phonerau1-866-664-2449.

Vousaurezbesoindevosnum@osdemodeleetdes@iesituessurlaparoiinterneducompartimentderefrig@ation.

SECURITEDU REFRIGERATEUR

Votre securite et celle des autres est tres importante.

Nous donnons de nombreux messages de s_curit_ importants dans ce manuel et sur votre appareil m_nager. Assurez-vous de

toujours lire tous les messages de s_curit_ et de vous y conformer.

Voici le symbole d'alerte de s_curit_.

Ce symbole d'alerte de s_curit_ vous signale les dangers potentiels de d_c_s et de blessures graves a vous

eta d'autres.

Tousles messages de s_curit_ suivront le symbole d'alerte de s_curit_ et le mot "DANGER" ou

"AVERTISSEMENT". Ces mots signifient •

Risque possible de d_cbs ou de blessure grave si vous ne

suivez pas imm_diatement les instructions.

Risque possible de d_cbs ou de blessure grave si vous

ne suivez pas les instructions.

Tousles messages de s_curit_ vous diront quel est le danger potentiel et vous disent comment r_duire le risque de blessure et

ce qui peut se produire en cas de non-respect des instructions.

IMPORTANTES INSTRUCTIONS DE SI_CURITI_

AVERTISSEMENT : Pour reduire les risques d'incendie, de choc electrique ou des blessures Iors de I'utilisation du

refrig6rateur, prendre quelques precautions fondamentales, y compris les suivantes •

• Brancher I'appareil sur une prise & 3 alveoles reliee a la terre.

• Ne pas enlever la broche de liaison & la terre.

• Ne pas utiliser un adaptateur.

• Ne pas utiliser un c&ble de rallonge.

• Debrancher la source de courant electrique avant I'entretien.

• Replacer pieces et panneaux avant de faire la remise en marche.

• Enlever les portes de votre vieux r6frigerateur.

• Utiliser un produit de nettoyage ininflammable.

• Garder les materiaux et les vapeurs inflammables, telle

que I'essence, loin du r6frigerateur.

• Utiliser deux ou plus de personnes pour deplacer et

installer le refrig6rateur.

• Debrancher le refrig6rateur avant I'installation de la

machine & glagons (seulement pour modeles pr_ts

recevoir une machine & glagons).

• Utiliser un verre robuste pour prendre des glagons (sur

certains modeles).

CONSERVEZ CES INSTRUCTIONS

Mise au rebut de votre vieux r( frig( rateur

Risque de suffoquer

Eniever Jes portes de votre vJeux r_frig_rateur.

Le non=respect de cette instruction peut causer

un d_c_s ou des I_sions c_r_brales.

IMPORTANT : L'emprisonnement et I'etouffement des enfants ne

sont pas un probleme du passe. Les refrigerateurs jetes ou

abandonnes sont encore dangereux, m_me s'ils sont laisses

abandonnes pendant "quelques jours seulement". Si vous vous

debarrassez de votre vieux refrigerateur, veuillez suivre les

instructions suivantes pour aider & eviter les accidents.

Avant de jeter votre vieux r_frig_rateur ou cong_lateur :

• Enlever les portes.

• Laisser les tablettes en place de sorte que les enfants ne

puissent pas y penetrer facilement.

----E

INSTRUCTIONSD'INSTALLATION

Debc Gge du ge Gteu ' Ex ge /sces d emD c ceme %

Risque du poids excessif

Utiliser deux ou plus de personnes pour d_placer et

installer le r_frig_rateur.

Le non=respect de cette instruction peut causer

une blessure au dos ou d'autre blessure.

Retirer les materiaux d'emballage. Ne pas utiliser d'instruments

coupants, d'alcool &friction, de liquides inflammables ou de

nettoyants abrasifs pour enlever le ruban adhesif ou la colle. Ces

produits peuvent endommager la surface de votre refrigerateur.

Pour plus de renseignements, voir "Securite du refrigerateur".

D_placement de votre r6frig6rateur :

Votre refrig6rateur est Iourd. Lors du deplacement de votre

refrig6rateur pour le nettoyage ou un entretien ou reparation,

veiller & recouvrir le plancher avec du carton ou un panneau

de fibres dures pour eviter qu'il ne subisse tout dommage.

Toujours tirer le refrig6rateur tout droit Iors de son

deplacement. Ne pas incliner le refrig6rateur d'un c6te ou de

I'autre nile "faire marcher" en essayant de le deplacer car le

plancher pourrait _tre endommag&

Importants renseignements a savoir au sujet des tablettes

et des couvercles en verre :

Ne pas nettoyer les tablettes ou couvercles en verre avec de

I'eau tiede quand ils sent froids. Les tablettes et les

couvercles peuvent se briser s'ils sent expos6s a des

changements soudains de temp@ature ou & un impact tel

que coup brusque. Le verre tremp_ est con_u pour 6clater

en d'innombrables pieces minuscules. Ceci est normal. Les

tablettes et les couvercles en verre sont Iourds. Les saisir

deux mains Iors de leur d_pose afin d'_viter de les faire

tomber.

Risque d'explosion

Garder les mat_riaux et les vapeurs inflammables, telle

que J'essence, Join du r6frig_rateur.

Le non=respect de cette instruction peut causer

un d_c_s, une explosion ou un incendie.

Pour obtenir une aeration appropriee pour votre refrigerateur,

laisser un espace de 1/2"(1,25 cm) de chaque c6te et au sommet.

Si vous installez votre refrigerateur pres d'un mur fixe, laisser un

minimum de 2" (5,08 cm) de chaque c6te (selon le modele) pour

permettre a la porte de s'ouvrir sans obstruction. Si votre

refrigerateur comporte une machine & glagons, s'assurer qu'un

espace additionnel est prevu & I'arriere pour permettre les

connexions des conduits d'eau.

2" (5_08crn)

REMARQUES :

IIest recommande de ne pas installer le refrig6rateur pres d'un

four, d'un radiateur ou de toute autre source de chaleur. Ne

pas installer le refrigerateur dans un endroit oQ la temperature

baissera au-dessous de 55°F (13°C).

La largeur de la cavite d'encastrement dolt etre d'au moins

36" (91,44 cm) pour I'installation du produit. Cependant, si le

produit est place contre une paroi relativement Iongue et si on

veut pouvoir retirer les bacs &legumes et & viande, il convient

d'elargir la cavite de 18" (45,72 cm). On recommande donc

une cavite d'encastrement d'une largeur totale de 54"

(137,16 cm).

Risque de choc _lectrique

Brancher sur une prise a 3 alv_oles reli_e a la terre.

Ne pas enlever la broche de liaison a la terre.

Ne pas utiliser un adaptateur.

Ne pas utiliser un c&ble de rallonge.

Le non=respect de ces instructions peut causer

un d_c_s, un incendie ou un choc _lectrique.

Avant de placer le refrigerateur & son emplacement final, il est

important de vous assurer d'avoir la connexion electrique

appropriee.

M_thode recommand_e de mise _ la terre

Une source d'alimentation de 115 volts, 60 Hz, type 15 ou

20 amperes CA seulement, protegee par fusible et adequatement

mise & la terre, est necessaire. IIest recommande d'utiliser un

circuit distinct pour alimenter uniquement votre refrigerateur.

Utiliser une prise murale qui ne peut pas etre mise hors circuit

I'aide d'un commutateur. Ne pas utiliser un c&ble de rallonge.

REMARQUE :Avant d'executer tout type d' installation, nettoyage

ou remplacement d'une ampoule d'eclairage, tourner la

commande (reglage du thermostat du refrigerateur ou du

congelateur selon le modele) a OFF (arret) et deconnecter ensuite

le refrigerateur de la source d'alimentation electrique. Lorsque

vous avez termine, reconnecter le refrigerateur & la source

d'alimentation electrique et tourner de nouveau la commande

(reglage du thermostat du refrigerateur ou du congelateur selon le

modele) au reglage desire. Voir "Utilisation des commandes".

-d} ........,,,_:;:,1_:**-_,_'_-,,_,_... (S wlet_*l'Q$O[} et*_ @Qtl

Rassembler les outils et pieces necessaires avant de commencer

I'installation. Lire et suivre les instructions fournies avec les outils

indiques ici.

OUTILLAGE REQUlS :

• Tournevis & lame plate

• Cles plates de 7Ae"et V#' ou

deux cles & molette reglables

• Tourne-ecrou de V4"

• Foret de V4"

• Perceuse sans fil

REMARQUE :Votre marchand de refrigerateurs presente une

trousse disponible avec un robinet d'arret & etrier de V4"

(6,35 mm), un raccord et un tube en cuivre. Avant I'achat,

s'assurer que le robinet d'arret &etrier est conforme & vos codes

Iocaux de plomberie. Ne pas employer de robinet d'arret a etrier

de 3Ae"(4,76 mm) ou de type & percer, ce qui reduit le debit d'eau

et cause une obstruction plus facilement.

IM PORTANT:

• Toutes les installations doivent etre conformes aux exigences

des codes Iocaux de plomberie.

• Utiliser un tube en cuivre et verifier s'il a des fuites. Installer les

tubes en cuivre seulement & des endroits oQ la temperature se

maintient au-dessus du point de congelation.

Pression de I'eau

Une alimentation en eau froide avec une pression entre 30 et

120 Ib/po _(207 et 827 kPa) est necessaire pour faire fonctionner

le distributeur d'eau et la machine &glagons. Si vous avez des

questions au sujet de la pression de votre eau, appeler un

plombier qualifie agree.

Alimentation en eau par osmose inverse

IMPORTANT : La pression de I'alimentation en eau entre le

systeme d'osmose inverse et la valve d'arrivee d'eau du

refrigerateur dolt etre entre 30 et 120 Ib/po 2(207 et 827 kPa).

Si un systeme de purification de I'eau par osmose inverse est

raccorde & votre alimentation en eau froide, la pression de I'eau

au systeme dolt etre d'un minimum de 40 a 60 Ib/po 2(276

414 kPa).

Si la pression de I'eau au systeme d'osmose inverse est inferieure

&40 a 60 Ib/po _(276 & 414 kPa) :

• Verifier si le filtre & sediment du systeme d'osmose inverse est

bloque et le remplacer si necessaire.

Laisser le reservoir du systeme d'osmose inverse se remplir

apres une utilisation intense.

Si votre refrigerateur a une cartouche de filtre & eau, celle-ci

peut reduire encore plus la pression de I'eau Iorsqu'elle est

utilisee avec un systeme d'osmose inverse. Retirer la

cartouche du filtre & eau. Voir "Systeme de filtration d'eau".

Si vous avez des questions au sujet de la pression de votre eau,

appeler un plombier qualifie agree.

B c cco dement de ton d e(su

Lire toutes les instructions avant de commencer.

IMPORTANT : Si on doit mettre en marche le refrig6rateur avant

qu'il soit raccorde &la canalisation d'eau, placer la commande de

la machine & glagons a la position OFF (arr_t).

Raccordement _ une canalisation d'eau

1. Debrancher le refrig6rateur ou deconnecter la source de

courant electrique.

2. FERMER le robinet principal d'arrivee d'eau. OUVRIR le

robinet de puisage le plus proche pendant une periode

suffisante pour que la canalisation d'eau se vide.

3. Trouver une canalisation d'eau froide verticale de

1/2"(12,7 mm) a 11/4"(3,18 cm) pres du refrigerateur.

IMPORTANT :

S'assurer qu'il s'agit d'une canalisation d'eau froide.

Un conduit horizontal fonctionnera, mais percer par le

dessus de la canalisation et non pas par le dessous. Ceci

permet de tenir le point de per£_age& I'ecart de I'eau et

d'emp_cher les sediments qu'on trouve normalement

dans I'eau de s'accumuler dans le robinet d'arr_t.

Pour determiner la Iongueur du tube en cuivre, il faut mesurer

la distance entre le point de connexion inferieur & I'arriere du

refrigerateur et le tuyau d'arrivee d'eau. Ajouter une Iongueur

de 7 pi (2,1 m) pour permettre le deplacement du refrigerateur

pour le nettoyage. Utiliser un tube en cuivre de 1/4"(6,35 mm)

de diametre exterieur. Veiller & ce que le tube soit coupe

d'equerre aux deux extremites.

/_,I'aide d'une perceuse sans ill, percer un trou de 1/4"

(6,35 mm) dans le tuyau de canalisation d'eau froide choisi.

A. Canafisation d'eau froide

B.Bride de tuyau

C. Tube en cuivre

D. E-crou de compression

E.Bague de compression

F. Robinet d'arr_t

G. E-crou de serrage

6. Fixer le robinet d'arr_t sur la canalisation d'eau froide avec la

bride de tuyau. Verifier que I'extremite de sortie du robinet est

bien engagee dans le trou de 1/4"(6,35 mm) perce dans la

canalisation et que la rondelle d'etancheite est placee sous la

bride de tuyau. Serrer I'ecrou de serrage. Serrer lentement et

uniformement les vis fixant la bride de prise en charge sur le

tuyau afin d'assurer I'etancheite de la rondelle. Ne pas serrer

excessivement car ceci pourrait provoquer I'ecrasement du

tube en cuivre.

7. Enfiler I'ecrou et la bague de compression sur le tube en

cuivre comme on le voit sur I'illustration. Inserer I'extremite du

tube aussi loin que possible dans I'extremite de sortie du

robinet. Visser I'ecrou de compression sur I'extremite de sortie

avec une cle & molette reglable. Ne pas serrer excessivement.

8. Placer le bout libre du tube dans un contenant ou evier et

OUVRIR le robinet principal d'arrivee d'eau et laisser I'eau

s'ecouler par le tube jusqu'& ce que I'eau soit limpide.

FERMER le robinet principal d'arrivee d'eau. Enrouler le tube

en cuivre en spirale.

Raccordement au r_frig_rateur

Style 1

1. Debrancher le refrigerateur ou deconnecter la source de

courant electrique.

2. Connecter le tube en cuivre & la valve d'arrivee d'eau en

utilisant un ecrou et une bague de compression tel qu'illustr&

Serrer I'ecrou de compression. Ne pas serrer excessivement.

3. Utiliser la bride du tube & I'arriere du refrigerateur pour fixer le

tube au refrigerateur tel qu'illustr& Ceci aide & eviter

d'endommager le tube Iorsque le refrigerateur est pousse

contre le mur.

OUVRIR le robinet d'arr_t.

Inspecter pour rechercher les fuites. Serrer tousles raccords

(y compris les raccordements au niveau de la valve d'entree

d'eau) ou les ecrous qui coulent.

A. Bride du tube D. E-crou de compression

B. Vis de bride de tube E. Valve d'entr_e d'eau

C. Tube en cuivre

La machine & glagons est equipee d'un filtre & eau incorpor&

Si laqualite de I'eau distribuee Iocalement necessite un

deuxieme filtre & eau, installer ce dernier dans la canalisation

d'eau de 1¼,,(6,35 mm) au niveau de I'un des raccords du

tuyau. On peut obtenir un tel filtre & eau chez le marchand

d'appareils electromenagers le plus proche.

Style 2

1. Debrancher le refrigerateur ou deconnecter la source de

courant electrique.

2. Retirer et jeter le bouchon en nylon noir du tuyau d'eau gris

I'arriere du refrigerateur.

3. Si letuyau gris fourni avec le refrigerateur n'est pas assez

long, un raccord de 1¼,,x 1¼,,(6,35 mm x 6,35 ram) est

necessaire afin de connecter la canalisation d'eau au conduit

d'eau existant dans la maison. Visser I'ecrou fourni sur le

raccord a I'extremite du tube de cuivre.

REMARQUE : Serrer I'ecrou & la main. Ensuite, le serrer avec

une cle deux tours de plus. Ne pas serrer excessivement.

A B C D

A. Conduit vers le r_frig_rateur

B. E-crou (foumi)

C. Renflement

D. Raccord (_ acheter)

E F G

E. Virole (_ acheter)

F. E-crou (_ acheter)

G. Canafisation

d'eau du domicile

OUVRIR le robinet d'arr_t.

Inspecter pour rechercher les fuites. Serrer tous les raccords

(y compris les raccordements de la valve d'entree d'eau) ou

les ecrous qui coulent.

Style 3

1. Debrancher le refrig6rateur ou deconnecter la source de

courant electrique.

2. Retirer et jeter le bouchon en nylon noir du tuyau d'eau gris

I'arriere du refrigerateur.

3. Enfiler I'ecrou fourni dans la valve d'entree d'eau comme sur

I'illustration.

REMARQUE • Serrer I'ecrou & la main. Ensuite, le serrer avec

une cle deux tours de plus. Ne pas serrer excessivement.

I/ II

A. Renflement

B. E-crou (fourni)

OUVRIR le robinet d'arret.

Inspecter pour rechercher les fuites. Serrer tousles raccords

(y compris les raccordements de la valve d'entree d'eau) ou

les ecrous qui coulent.

Achever I'installation

Risque de choc _lectrique

Brancher sur une prise a 3 alv_oles reli_e a la terre.

Ne pas enJever la broche de liaison a la terre.

Ne pas utiliser un adaptateur.

Ne pas utiliser un c&ble de rallonge.

Le non=respect de ces instructions peut causer

un d_c_s, un incendie ou un choc _lectrique.

1. Brancher sur une prise &3 alveoles reliee a la terre.

2. Vider le systeme d'eau. Voir "Preparer le systeme d'eau" ou

"Distributeurs d'eau et de glagons".

REMARQUE : Attendre 24 heures pour produire la premiere

quantite de glagons. Attendre 3 jours pour que le bac a glagons

se remplisse entierement.

U]'ILISATION

DU REFRIGERATEUR

Pour votre commodite, les commandes du refrigerateur sont

prereglees & I'usine. Lors de I'installation initiale du refrigerateur,

s'assurer que les commandes sont encore prereglees. La

commande du refrigerateur et celle du congelateur devraient

toutes les deux se trouver aux "reglages moyens".

FREEZER REFRIGERATOR

@ @

2 4

COLD 1@5 COLDER z_ _L

COLD 1 5 COLDER

oC_

IMPORTANT :

• Votre produit ne se refroidira pas quand la commande du

RI2FRIGERATEUR se trouve a OFE

La commande du refrigerateur regle la temperature du

compartiment de refrigeration. La commande du congelateur

regle la temperature du compartiment de congelation. Les

reglages & la gauche du reglage moyen sont pour une

temperature moins froide. Ceux qui se trouvent & droite sont

pour une temperature plus froide.

Attendre 24 heures avant de mettre des aliments au

refrigerateur. Si I'on ajoute des aliments avant que le

refrigerateur ait refroidi completement, les aliments peuvent

s'abimer.

REMARQUE :Tourner les commandes du refrigerateur et du

congelateur & un reglage plus eleve (plus froid) que le reglage

recommande ne refroidira pas les compartiments plus

rapidement.

Ajustement des commandes

Donner au refrigerateur le temps de refroidir completement avant

d'y ajouter des aliments. IIest preferable d'attendre 24 heures

avant de placer les aliments au refrigerateur. Les reglages

indiques dans la section precedente devraient etre corrects pour

I'utilisation normale du refrigerateur domestique. Les reglages

sont faits correctement Iorsque le lait ou le jus est aussi froid que

vous I'aimez et Iorsque la creme glacee est ferme.

Tourner la commande vers la droite (dans le sens horaire) pour

rendre le compartiment plus froid. Tourner la commande vers la

gauche (dans le sens antihoraire) pour le rendre moins froid. Pour

eteindre le systeme de refroidissement, tourner la commande du

refrigerateur dans le sens antihoraire & la position OFF (arret).

S'il est necessaire d'ajuster les temperatures dans le refrigerateur

ou congelateur, utiliser les reglages indiques dans le tableau ci-

dessous comme guide. Attendre au moins 24 heures entre les

ajustements.

CONDITION/RAISON : AJUSTEMENT :

RItFRIGItRATEUR trop tiede Regler la commande

du RItFRIGItRATEUR

&un degre plus eleve

CONGItLATEUR trop tiede/ Regler la commande

trop peu de glagons du CONGItLATEUR

&un degre plus eleve

R#FRIG#RATEUR trop froid Regler la commande

du RItFRIGItRATEUR

&un degre plus bas

CONG#LATEUR trop froid Regler la commande

du CONGItLATEUR

&un degre plus bas

De I'air froid du congelateur passe directement dans le

compartiment de la porte du refrigerateur situe sous les events.

REMARQUE • Le compartiment & produits laitiers et le porte-

canettes ne sont pas associes &la caracteristique Compartiment

froid de la porte.

Commande du compartiment froid de la porte

La commande du compartiment froid de la porte se trouve sur le

c6te gauche du compartiment de refrigeration.

La commande peut _tre ajustee pour bien refroidir les viandes ou

les legumes. L'air a I'interieur du contenant est refroidi pour eviter

les "pelts espaces" de congelation et peut _tre regle pour garder

les viandes aux temperatures de conservation de 28° & 32°F

(de -2° &0°C) recommandees par I'Office national du betail et des

viandes. La commande du tiroir convertible & legumes/viande est

prereglee au reglage le plus bas pour la viande.

Pour conserver la viande •

Regler la commande a un des trois reglages MEAT (viande) pour

conserver la viande a la temperature ideale.

Pour conserver les 16gumes •

Regler la commande &VEG (legumes) pour conserver les legumes

&la temperature ideale.

REMARQUE • Si les aliments commencent & congeler, deplacer

la commande vers la gauche (moins froid). Ne pas oublier

d'attendre 24 heures entre les ajustements.

eg , mes

_+](S_<#= s,,,<,'Ci; % 11_ _ _ +J,,, _+;i ;?'J<B

On peut contreler le degre d'humidite dans le bac i legumes

etanche. La commande peut @treajustee &n'importe quel reglage

entre LOW et HIGH.

LOW (bas)(ouvert) pour une meilleure conservation des fruits et

des legumes a pelures.

HIGH (eleve)(ferme) pour une meilleure conservation des legumes

frais et & feuilles.

A .....

A. Commande du compartiment froid de la porte

Deplacer le bouton de commande du compartiment froid de la

porte vers la gauche pour reduire la circulation d'air froid dans

le compartiment et le rendre ainsi moins froid.

Deplacer le bouton de commande du compartiment froid de la

porte vers la droite pour augmenter la circulation d'air froid

dans le compartiment et le rendre ainsi plus froid.

'++I ,, I; I ....

(su_'ce tc_ns mo(_@®s

Selon votre modele, vous pouvez choisir une ou plusieurs des

options suivantes • la possibilite de choisir de la glace concassee

ou en cubes, eau refrigeree, une lampe speciale qui s'allume

I'occasion de I'utilisation du distributeur, ou une option de

verrouillage pour eviter une distribution non intentionnelle.

REMARQUES :

• Le systeme de distribution ne fonctionne pas Iorsque la porte

du congelateur est ouverte.

Apres avoir connecte le refrigerateur &une source

d'alimentation en eau, vidanger le systeme d'eau. Utiliser un

recipient robuste pour appuyer sur le levier du distributeur

d'eau pendant 5 secondes, puis rel&cher pendant

5 secondes. Repeter I'operation jusqu'& ce que I'eau

commence & couler. Une fois que I'eau commence & couler,

repeter I'operation (appui sur le levier du distributeur pendant

5 secondes puis rel&chement pendant 5 secondes) pendant

5 minutes supplementaires. Ceci permettra d'evacuer I'air du

filtre et du systeme de distribution d'eau. Une vidange

supplementaire peut _tre necessaire dans certains domiciles.

Pendant I'evacuation de I'air du systeme, de I'eau peut gicler

du distributeur.

Sur certains modeles •Accorder 24 heures pour que le

refrigerateur se refroidisse et refroidisse I'eau.

Accorder 24 heures pour produire la premiere quantite de

gla£;ons. Jeter les trois premieres quantites de glagons

produites.

Le distributeur d'eau

IMPORTANT : Puiser une quantite suffisante d'eau chaque

semaine pour maintenir un approvisionnement frais.

Distribution d'eau :

1. Appuyer un verre resistant contre le levier de distribution

d'eau.

2. Retirer le verre pour arr_ter la distribution.

Le distributeur de glace

Le systeme de distribution ne fonctionne pas Iorsque la porte du

congelateur est ouverte. La glace est distribuee du bac

d'entreposage de la machine a glagons dans le congelateur

Iorsque le levier de distribution est abaiss&

REMARQUE : Certains modeles distribuent des glagons en

cubes et de la glace concassee. Avant la distribution de glagons,

choisir le type de glace desir&

Pour de la glace concassee, les glagons sont concasses avant

d'etre distribu6s. Cette action peut causer un court delai Iors de la

distribution de glace concassee. Le bruit du broyeur de glagons

est normal et la dimension des morceaux de glace peut varier.

Lorsqu'on change de concassee a glagons, quelques onces de

glace concassee seront distribu6es avec les premiers glagons.

Distribution de glace :

1. Appuyer sur le bouton pour selectionner le type de glace

desir&

La lumi_re du distributeur

Style 1

La lumiere du distributeur peut _tre allumee en appuyant sur le

bouton ON (marche).

Les lumieres du distributeur sont des DEL et ne devraient pas

avoir besoin d'etre changees. Voir "Depannage" pour de plus

amples informations.

Style 2

Lorsqu'on utilise le distributeur, le levier allume automatiquement

la lumiere. Pour avoir la lumiere allumee en permanence,

selectionner ON ou NIGHT LIGHT (veilleuse).

ON : Appuyer sur le bouton LIGHT pour eclairer le distributeur.

NIGHT LIGHT : Appuyer sur le bouton LIGHT une deuxieme fois

pour selectionner le mode Night Light. La lumiere du distributeur

s'ajustera automatiquement pour eclairer plus ou moins en

fonction de la clarte de la piece.

OFF : Appuyer sur le bouton LIGHT une troisieme fois pour

eteindre la lumiere du distributeur.

Les lumieres du distributeur sont des DEL et ne devraient pas

avoir besoin d'etre changees. Si les lumieres du distributeur ne

fonctionnent pas, verifier que le detecteur de lumiere n'est pas

bloqu6 (en mode Night Light). Voir "Depannage" pour de plus

amples informations.

Risque de coupure

Utiliser un verre robuste pour prendre des glagons.

Le non-respect de cette instruction peut causer

des coupures.

Appuyer un verre solide contre le levier du distributeur de

glagons. Tenir le verre pres de I'ouverture du distributeur pour

que les glagons ne tombent pas & c6te du verre.

IMPORTANT : IIn'est pas necessaire d'appliquer beaucoup

de pression au levier pour activer le distributeur de glagons.

Une pression forte ne donne pas une distribution plus rapide

de glagons ou des quantites plus grandes.

3. Retirer le verre pour arr_ter la distribution.

Le verrouillage du distributeur (sur certains modules)

Le distributeur peut _tre verrouille pour un nettoyage facile ou

pour eviter la distribution involontaire par de jeunes enfants ou

des animaux de compagnie.

REMARQUE : La caracteristique de verrouillage ne coupe pas

I'alimentation electrique & I'appareil, & la machine & glagons ou &

la lumiere du distributeur. Elle desactive simplement les leviers du

distributeur. Les distributeurs de glagons et d'eau ne

fonctionneront pas.

Style 1 : Appuyer sur le bouton LOCK (verrouillage) pour

verrouiller le distributeur. Appuyer sur le bouton UNLOCK

(deverrouillage) pour deverrouiller le distributeur.

Style 2 :Appuyer sur le bouton LOCK OUT (verrouille) pour

verrouiller le distributeur. Appuyer une deuxieme fois sur le bouton

LOCK OUT (verrouille) pour deverrouiller le distributeur.

Mise en marche/arr_t de la machine & glaqons

• Pour mettre la machine a glagons EN MARCHE, il suffit

d'abaisser le bras de commande en broche.

Pour arr_ter manuellement la machine a glagons, soulever le

bras de commande en broche & la position OFF (elev6e) et

attendre le clic. Les glagons peuvent encore _tre distribu_s,

mais aucun autre glagon ne peut _tre fait.

REMARQUE :Votre machine & glagons a un arr_t automatique.

Au fur et & mesure de la fabrication de la glace, les glagons

remplissent le bac d'entreposage de glagons. Les glagons

soulevent le bras de commande en broche & la position OFF

(elevee). Ne pas forcer le commutateur du bras en broche vers le

haut ou vers le bas.

La page charge ...

IKEA ID5HHEXVQ00 Le manuel du propriétaire

Marque: IKEA

Modèle: ID5HHEXVQ00

Catégorie: Frigos

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: IKEA ID5HHEXVQ00 Owner's manual

IKEA ID5HHEXVQ00 Le manuel du propriétaire

Ce manuel convient également à

IKEA ID5HHEXVQ00 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents