Amana NGD4600YQ0 Guide d'installation

DRYER iNSTALLATiON iNSTRUCTiONS

29" and 27" Wide Models

Gas (U.S.A. and Canada} & Electric (Canada Only)

iNSTRUCTiONS D'INSTALLATION DE LA SECHEUSE

ModUles de 29" et de 27" de largeur

A gaz (i_.-U. et Canada) et I_lectrique (Canada uniquement)

Para obtener acceso al manual de uso y cuidado en espa_ol, o para obtener informaci6n adicional acerca de su producto, visite:

www.whirlpool.com

Tenga listo su nOmero de modelo completo. Puede encontrar el nOmero de modelo y de serie dentro de la cavidad superior de la puerta.

Table of Contents TabHe des mati_res

DRYER SAFETY ................................................................ 2

INSTALLATION REQUIREMENTS .................................... 4

Tools and Parts .................................................................... 4

Location Requirements ...................................................... 5

ELECTRIC DRYER POWER HOOKUP - CANADA ONLY ......... 7

Electrical Requirements ..................................................... 7

install Leveling Legs ........................................................... 7

GAS DRYER POWER HOOKUP ................................................. 8

Gas Supply Requirements .................................................. 8

Electrical Requirements ..................................................... 9

VENTING .................................................................................... 10

Venting Requirements ....................................................... 10

Plan Vent System ............................................................... 11

Venting Kits ........................................................................ 11

install Vent System ............................................................ 12

Make Gas Connection ...................................................... 13

Connect Vent ..................................................................... 13

LEVEL DRYER ........................................................................... 14

COMPLETE INSTALLATION CHECKLIST ............................... 14

REVERSE DOOR SWING (OPTIONAL} .................................... 14

TROUBLESHOOTING ............................................................... 22

SECURIT¢:: DE LA SC:CHEUSE ....................................... 23

EXIGENCES D'INSTALLATION ...................................... 25

Outillage et pi_ces ............................................................ 25

Exigences d'emplacement ............................................... 26

RACCORDEMENT A UALIMENTATION leLECTRIQUE

DE LA SI'-=CHEUSE #LECTRIQUE - CANADA SEULEMENT ... 28

Specifications 6iectriques ................................................ 28

Installation des pieds de nivellement .............................. 29

RACCORDEMENT D'UNE SECHEUSE A GAZ ....................... 29

Specifications de I'alimentation en gaz .......................... 29

Specifications _lectriques ................................................ 31

UleVACUATION .......................................................................... 32

Exigences concernant I'_vacuation ................................ 32

Planification du syst_me d'_vacuation ........................... 33

Trousses d'6vacuation ...................................................... 33

Installation du circuit d'_vacuation ................................. 35

Raccordement au gaz ....................................................... 35

Raccordement du conduit d'_vacuation ......................... 36

REGLAGE DE L'APLOMB DE LA Si'-=CHEUSE......................... 36

ACHEVER L'INSTALLATION - LISTE DE VLeRIFICATION ....... 37

INVERSION DU SENS DE L'OUVERTURE DE LA PORTE

(FACULTATIF) ............................................................................. 37

Di'-=PANNAG E ............................................................................. 47

iNSTALLATiON NOTES

Date of purchase:

Date of installation:

Installer:

Model number:

Serial number:

NOTES CONCERNANT L'INSTALLATION

Date d'achat :

Date d'installation :

Installateur :

Num_ro de module :

Num_ro de s_rie :

W10115228C

W10115229C=SP

DRYER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

WARNING - ...i.. ofFi,o..

= Clothes dryer installation must be performed by a qualified installer,

= Install the clothes dryer according to the manufacturer's instructions and local codes.

- Do not install a clothes dryer with fle×ible plastic venting materials or fle×ible metal

(foil type) duct. if fle×ible metal duct is installed, it must be of a specific type identified

by the appliance manufacturer as suitable for use with clothes dryers. Fie×ible venting

materials are known to coflapse, be easily crushed, and trap lint. These conditions will

obstruct clothes dryer airflow and increase the risk of fire.

= To reduce the risk of severe injury or death, follow all installation instructions.

= Save these instructions.

iMPORTANT: The gas installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas

Code, ANSI Z223.1iNFPA 54 or the Canadian Natural Gas and Propane Installation Code, CSA B149.1.

The dryer must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National

Electrical Code, ANSI/NFPA 70 or Canadian Electrical Code, CSA C22.1.

2

WARNING: For your safety, the information in this manual must be followed to minimize

the risk of fire or explosion, or to prevent property damage, personal injury, or death.

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this

or any other appliance.

- WHAT TO DO iF YOU SMELL GAS:

= Do not try to light any appliance.

® Do not touch any electrical switch; do not use any phone in your building.

• Clear the room, building, or area of all occupants.

• Immediately carl your gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

• if you cannot reach your gas supplier, carl the fire department.

- Installation and service must be performed by a qualified installer, service agency, or

the gas supplier.

WARNING: Gas leaks cannot always be detected by smell.

Gas suppliers recommend that you use a gas detector approved by UL or CSA.

For more information, contact your gas supplier.

If a gas leak is detected, follow the "What to do if you smell gas" instructions.

iMPORTANT SAFETY iNSTRUCTiONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic precautions,

including the following:

[] Read all instructions before using the dryer.

[] Do not place items exposed to cooking oils in your dryer.

Items contaminated with cooking oils may contribute to

a chemical reaction that could cause a load to catch fire.

[] Do not dry articles that have been previously cleaned in,

washed in, soaked in, or spotted with gasoline, dry=

cleaning solvents, or other flammable or explosive

substances as they give off vapors that could ignite or

explode.

[] Do not allow children to play' on or in the dryer. Close

supervision of children is necessary when the dryer is

used near children.

[] Before the dryer is removed from service or discarded,

remove the door to the drying compartment.

[] Do not reach into the dryer if the drum is moving.

[] Do not install or store the dryer where it will be exposed

to the weather.

[] Do not tamper with controls.

[] Do not repair or replace any part of the dryer or attempt

any servicing unless specifically recommended in this

Use and Care Guide or in published user=repair

instructions that you understand and have the skills to

carry out.

[] Do not use fabric softeners or products to eliminate static

unless recommended by the manufacturer of the fabric

softener or product.

[] Do not use heat to dry articles containing foam rubber or

similarly textured rubber=like materials.

[] Clean lint screen before or after each load.

[] Keep area around the exhaust opening and adjacent

surrounding areas free from the accumulation of lint, dust,

and dirt.

[] The interior of the dryer and exhaust vent should be

cleaned periodically by qualified service personnel.

[] See "Electrical Requirements" located in the installation

instructions for grounding instructions.

SAVE THESE iNSTRUCTiONS

In the State of Massachusetts, the following installation instructions apply:

[] Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by

the State of Massachusetts.

[] If using a ball valve, it shall be a T-handle type.

[] A flexible gas connector, when used, must not exceed 3 feet.

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

IMPORTANT SAFETY INSTRUCTIONS

When discarding or storing your old clothes dryer, remove the door.

SAVE THESE INSTRUCTIONS

iNSTALLATION

Toomsand Parts

Gather the required tools and parts before starting installation.

Tools needed for all installations:

Adjustable wrench that

opens to 1" (25 mm) or

hex-head socket wrench

REQUIREMENTS

Caulking gun and compound

(for installing new exhaust vent)

Flat-blade screwdriver

#2 Phillips screwdriver

1/4" nut driver or socket

wrench (recommended)

Tape measure

Level Pliers

4

Tin snips (new vent

installations)

Vent clamps

Utility knife Putty knife

Tools needed for gas installations:

8" or 10" pipe wrench

Pipe-joint compound

resistant to LP gas

8" or 10" adjustable wrench

(for gas connections)

Parts supplied:

[

Leveling legs (4)

Parts package is located in dryer drum. Check that all parts

are included.

Parts needed:

Check local codes. Check existing electrical supply and venting.

See "Electrical Requirements" and "Venting Requirements"

before purchasing parts.

Mobile home installations require metal exhaust system

hardware, available for purchase from the dealer from whom

you purchased your dryer. For further information, please

reference the "Assistance or Service" section of the Use and

Care Guide.

Optional Equipment: (Not supplied with dryer)

Refer to your Use and Care Guide for information about

accessories available for your dryer.

Location Requirements

[] If you are using power supply cord, a grounded electrical

outlet located within 2 ft. (610 mm) of either side of dryer.

See "Electrical Requirements."

[] A sturdy floor to support dryer and a total weight (dryer

and load) of 200 Ibs. (90.7 kg). The combined weight of

a companion appliance should also be considered.

[] Level floor with maximum slope of 1" (25 mm) under entire

dryer. If slope is greater than 1" (25 mm), install Extended

Dryer Feet Kit, Part Number 279810. If not level, clothes

may not tumble properly and automatic sensor cycles

may not operate correctly.

Do not operate your dryer at temperatures below 45°F (7°C).

At lower temperatures, the dryer might not shut off at the end

of an automatic cycle. Drying times can be extended.

The dryer must not be installed or stored in an area where it will

be exposed to water and/or weather.

Check code requirements. Some codes limit, or do not permit,

installation of the dryer in garages, closets, mobile homes, or

sleeping quarters. Contact your local building inspector.

NOTE: No other fuel-burning appliance can be installed in the

same closet as a dryer.

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Place dryer at least 18 inches (460 ram) above the floor

for a garage installation.

Failure to do so can result in death, explosion, or fire.

You will need:

[] A location allowing for proper exhaust installation.

See "Venting Requirements."

[] A separate 30-amp circuit for electric dryers.

[] A separate 15- or 20-amp circuit for gas dryers.

Installation clearances:

The location must be largeenough to allow the dryer door to open fully.

Most installations require a minimum 51/2"(140 mm) clearance behind the dryer for the exhaust vent with elbow. See "Venting

Requirements."

29" Wide Models

Dryer Dimensions

223/4" i

_=/8" I IIIIIF_ t=(578ram) I /

(110=retailII ,3'/8"/

I III-( J I( " 11(-02mm

i

,=0II II k

(660ram} (705mm)._

(737ram)

A

228h,,

(737_m)

228/4"

_8/8,,I _ ..__._._____(578ram) _8/8"i

(1102mm) II_]_ (1102mm)1III/ l_II _8,,,I I1 ',

"273/,"_\ I '-_--'-'--_-JII "273/""'__'II_

1705mm). _r-_. _ (705ram),__,

(737ram) (737ram)

C D

A. Large opening side-swing door

B. Large opening side-swing door

C. Wide opening side-swing door

D. Wide opening hamper door

installation Spacing

ooii

(457 mm_l

_.=_] o/' max,' -

48in_*

_ I_ II;._ mm 310cm)__

[_ 24in.2.-

-.. ._ (155cm)_

1"-_ _- 29"-_ _- 1" -_1"*_ 273_"H5V]'__-

(25ram} (737mm) (25mm)(25mm)(705mrn}(140ram}

A B

E}

C

A. Recessed area

B. Side view - closet or confined area

C. Closet door with vents

i_ 3"*

(76ram)

-T

(76rnm}

*Required spacing

27" Wide Models

Dryer Dimensions

i 23%"

1t092 ram) (1092mn_)I Ill )JI 13=A"

I Ilk __...J] 1349ram)

i \

(749rnrn} X _--._. -27" -'" (749 ram) \ ,'%F 27" _'"

.- -27"

-_ (687 ram) _="(687 ram}

A B

A. Large opening side-swing door

B. Wide opening hamper door

Installation Spacing

1"-_tI_ 27"_ I<- 1"

(25ram)(686mm)

A

_ 14"max,*

-- _ --_in._

__ (310cm)

__ 24i_*

\I _ k_ (1550m:

(25mm)(25mm)(748mm}(148mm}

B C

A. Recessed area

B. Side view - closet or confined area

C. Closet door with vents

*Required spacing

_f 3 I1.

-_6 ram)

7

3"*

(76ram)

T

Installation spacing for recessed area or closet

The dimensions shown are for the minimum spacing allowed.

[] Additional spacing should be considered for ease of

installation and servicing.

[] Additional clearances might be required for wall, door, and

floor moldings.

[] Additional spacing of 1" (25 mm) on all sides of the dryer is

recommended to reduce noise transfer.

[] For closet installation, with a door, minimum ventilation

openings in the top and bottom of the door are required.

Louvered doors with equivalent ventilation openings are

acceptable.

[] Companion appliance spacing should also be considered.

Mobile home-Additional installation requirements

This dryer is suitable for mobile home installations. The

installation must conform to the Manufactured Home

Construction and Safety Standard, Title 24 CFR, Part 3280

(formerly the Federal Standard for Mobile Home Construction

and Safety, Title 24, HUD Part 280) or the Canadian

Manufactured Home Standard CAN/CSA-Z240 MH.

[] Metal exhaust system hardware, available for purchase.

For further information, please reference the "Assistance or

Service" section of the Use and Care Guide.

[] Special provisions must be made in mobile homes to

introduce outside air into the dryer. The opening (such as a

nearby window) should be at least twice as large as the dryer

exhaust opening.

6

ELECTRIC DRYER POWER

HOOKUP - CANADA ONLY

E ectdcal Requirements

Electrical Shock Hazard

Plug into a grounded 4 prong outlet.

Failure to do so can result in death or electrical shock.

it is your responsibility:

[] To contact a qualified electrical installer.

[] To be sure that the electrical connection is adequate

and in conformance with the Canadian Electrical Code,

C22.1 - latest edition and all local codes. A copy of the

above codes standard may be obtained from: Canadian

Standards Association, 178 Rexdale Blvd., Toronto, ON

M9W 1R3 CANADA.

[] To supply the required 4-wire, single-phase, 120/240 volt,

60 Hz., AC-only electrical supply on a separate 30-amp

circuit, fused on both sides of the line. A time-delay fuse or

circuit breaker is recommended. Connect to an individual

branch circuit.

[] This dryer is equipped with a CSA international Certified

Power Cord intended to be plugged into a standard 14-30R

wall receptacle. The cord is 5 ft. (1.52 m) in length. Be sure

wall receptacle is within reach of dryer's final location.

4-wire receptacle (14-30R)

[] Do not use an extension cord.

If using a replacement power supply cord, it is recommended that

you use Power Supply Cord Replacement Part Number 8579325.

For further information, please reference the "Assistance or

Service" section of the Use and Care Guide.

GROUNDING INSTRUCTIONS

m For a grounded, cord-connected dryer:

This dryer must be grounded. In the event of malfunction or

breakdown, grounding will reduce the risk of electric shock

by providing a path of least resistance for electric current.

This dryer is equipped with a cord having an equipment-

grounding conductor and a grounding plug. The plug must

be plugged into an appropriate outlet that is properly

installed and grounded in accordance with all local codes

and ordinances.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or service representative

or personnel if you are in doubt as to whether the dryer is

properly grounded. Do not modify the plug provided with

the dryer: if it will not fit the outlet, have a proper outlet

installed by a qualified electrician.

SAVE THESE INSTRUCTIONS

mnstaH Leve ing Legs

Excessive Weight Hazard

Use two or more people to move and install dryer.

Failure to do so can result in back or other injury.

1. Prepare dryer for leveling legs

\

To avoid damaging floor, use a large flat piece of cardboard

from dryer carton; place under entire back edge of dryer.

Firmly grasp dryer body (not console panel) and gently lay

dryer down on cardboard.

2, Screw in leveling legs

diamond

marking

Examine leveling legs and find diamond marking. Screw legs

into leg holes by hand. Use a wrench to finish turning legs

until diamond marking is no longer visible.

Now stand the dryer on its feet. Slide the dryer until it is

close to its final location. Leave enough room to connect

the exhaust vent.

For mobile home use

Gas dryers must be securely fastened to the floor.

Mobile home installations require a Mobile Home Installation

Hold-down Kit. For ordering information please reference

the Use and Care Guide.

GAS DRYER POWER

HOOKUP

Gas Supply Requirements

Explosion Hazard

Use a new CSA international approved gas supply line.

Install a shut=off valve.

Securely tighten all gas connections.

if connected to LP, have a qualified person make sure

gas pressure does not exceed 13" (330 ram) water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

8

Gas type

Natural gas:

This dryer is equipped for use with Natural Gas. It is design-

certified by CSA International for LP (propane or butane) gases

with appropriate conversion.

[]

Your dryer must have the correct burner for the type of gas

in your home. Burner information is located on the rating

plate in the door well of your dryer. If this information does

not agree with the type of gas available, please reference the

"Assistance or Service" section of the Use and Care Guide.

LP gas conversion:

Conversion must be made by a qualified technician.

No attempt shall be made to convert the dryer from the gas

specified on the model/serial rating plate for use with a different

gas without consulting the serving gas supplier.

iMPORTANT: The gas installation must conform with local codes,

or, in the absence of local codes, with the National Fuel Gas

Code, ANSI Z223.1/NFPA 54 or the Canadian Natural Gas and

Propane Installation Code, CSA B149.1.

Gas supply line

[] 1/2" NPT pipe is recommended.

[] 3/8" approved tubing is acceptable for lengths under

20 ft. (6.1 m) if local codes and gas supplier permit.

[] Must include 1/8" NPT minimum plugged tapping accessible

for test gauge connection, immediately upstream of the gas

connection to the dryer (see illustration).

[] Must include a shut-off valve:

In the U.S.A.:

An individual manual shut-off valve must be installed

within six (6)feet (1.8 m) of the dryer in accordance with

the National Fuel Gas Code, ANSI Z223.1.

in Canada:

An individual manual shut-off valve must be installed in

accordance with the B149.1, Natural Gas and Propane

Installation Code. It is recommended that an individual

manual shut-off valve be installed within six (6) feet (1.8 m)

of the dryer.

The shut-off valve location should be easy to reach for opening

and closing.

E

B

A. 3/8" flexible gas connector

B.3/8" pipe to flare adapter fitting

C. 1/8" NPT minimum plugged tapping

D. 1/2" NPT gas supply line

E. Gas shut-off valve

Gas supply connection requirements

There are many methods by which your gas dryer can be

connected to the gas supply. Listed here are some guidelines

for two different methods of connection.

This dryer must be connected to the gas supply line with a

listed flexible gas connector that complies with the standard for

connectors for gas appliances, ANSI Z21.24 or CSA 6.10.

Option1(RecommendedMethod}

Flexible stainless steel gas connector:

[] If local codes permit, use a new flexible stainless steel gas

connector (Design Certified by the American Gas Association

or CSA International) to connect your dryer to the rigid gas

supply line. Use an elbow and a 3/8" flare x 3/8" NPT adapter

fitting between the stainless steel gas connector and the

dryer gas pipe, as needed to prevent kinking.

Option 2 (Alternate Method}

Approved aluminum or copper tubing:

[] Lengths over 20 ft. (6.1 m) can use 3/8" approved tubing

(if codes and gas supplier permit).

[] If you are using Natural Gas, do not use copper tubing.

[] 3/8" flare x 3/8" NPT adapter fitting between dryer pipe and

3/8" approved tubing.

[] Lengths over 20 ft. (6.1 m) should use larger tubing and a

different size adapter fitting.

[] If your dryer has been converted to use LP gas, 3/8" LP

compatible copper tubing can be used. If the total length

of the supply line is more than 20 ft. (6.1 m), use larger pipe.

NOTE: Pipe joint compounds that resist the action of LP

gas must be used. Do not use TEFLON _>ttape.

Dryer gas pipe

[] The gas pipe that comes out through the rear of your dryer

has a 3/8" male pipe thread.

29" Wide Model

27" Wide Model

A 9¼ "-_

(235 ram}

1¼"

(32 rnm}

A. 3/8" NPT dryer pipe

5 3/4"

(159 mm)

A

t 1/2"

(38 rnrn)

A. 3/8" NPT dryer pipe

Burner input requirements

Elevations up to 10,000 ft. (3,048 m}:

[] The design of this dryer is certified by CSA international for

use at altitudes up to 10,000 ft. (3,048 m), above sea level at

the B.T.U. rating indicated on the model/serial number plate.

Burner input adjustments are not required when the dryer is

operated up to this elevation.

Elevations above 10,000 ft. (3,048 m}:

[] When installed above 10,000 ft. (3,048 m) a 4% reduction

of the burner B.T.U. rating shown on the model/serial

number plate is required for each 1,000 ft. (305 m)

increase in elevation.

Gas supply pressure testing

[] The dryer must be disconnected from the gas supply piping

system during pressure testing at pressures greater than

1/2 psi.

Electrica Requ

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter,

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

[]

120 Volt, 60 Hz., AC only, 15- or 20-amp fused electrical

supply is required. A time-delay fuse or circuit breaker is

recommended, it is also recommended that a separate circuit

serving only this dryer be provided.

GROUNDING INSTRUCTIONS

[] For a grounded, cord-connected dryer:

This dryer must be grounded, in the event of malfunction or

breakdown, grounding will reduce the risk of electric shock

by providing a path of least resistance for electric current.

This dryer is equipped with a cord having an equipment-

grounding conductor and a grounding plug. The plug must

be plugged into an appropriate outlet that is properly

installed and grounded in accordance with all local codes

and ordinances.

WARNING: improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or service representative

or personnel if you are in doubt as to whether the dryer is

properly grounded. Do not modify the plug provided with

the dryer: if it will not fit the outlet, have a proper outlet

installed by a qualified electrician.

SAVE THESE INSTRUCTIONS

1-®)TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

9

VENTING

Venting Requirements

Fire Hazard

Use a heavy metal vent.

Do not use a plastic vent.

Do not use a metal foil vent,

Failure to follow these instructions can result in death

or fire.

WARNING: To reduce the risk of fire, this dryer MUST BE

EXHAUSTED OUTDOORS.

IMPORTANT: Observe all governing codes and ordinances.

Exhaust hoods:

[] Must be at least 12" (305 ram) from ground or any object

that may obstruct exhaust (such as flowers, rocks, bushes,

or snow).

Recommended Styles:

Louveredhood

Acceptable Style:

Box hood

Dryer exhaust must not be connected into any gas vent,

chimney, wall, ceiling, attic, crawlspace, or a concealed space

of a building. Only rigid or flexible metal vent shall be used for

exhausting.

!

(102 ram)

{

4" (102 mm) heavy metal exhaust vent

[] Only a 4" (102 mm) heavy metal exhaust vent and clamps

may be used.

[] Do not use plastic or metal foil vent.

Rigid metal vent:

[] Recommended for best drying performance and to avoid

crushing and kinking.

Flexible metal vent: (Acceptable only if accessible to clean)

[] Must be fully extended and supported in final dryer location.

[] Remove excess to avoid sagging and kinking that may result

in reduced airflow and poor performance.

[] Do not install in enclosed walls, ceilings, or floors.

[] The total length should not exceed 73/4ft. (2.4 m).

NOTE: If using an existing vent system, clean lint from entire

length of the system and make sure exhaust hood is not

plugged with lint. Replace plastic or metal foil vents with rigid

metal or flexible metal vents. Review "Vent System Chart" and,

if necessary, modify existing vent system to achieve best drying

performance.

Angled hood

Elbows:

[] 45° elbows provide better airflow than 90° elbows.

............. Bet

Clamps:

[] Use clamps to seal all joints.

[] Exhaust vent must not be connected or secured with screws

or other fastening devices that extend into interior of duct

and catch lint. Do not use duct tape.

Improper venting can cause moisture and lint to collect

indoors, which may result in:

[] Moisture damage to woodwork, furniture, paint, wallpaper,

carpets, etc.

[] Housecleaning problems and health problems.

See "Venting Kits" for more information.

10

P an Vent System

Recommended exhaust installations

Typical installations vent the dryer from the rear of the dryer.

Other installations are possible.

A--

O

B

G

_H

A. Dryer

B. Elbow

C, Wall

D. Exhaust hood

E. Clamps

F. Rigid metal or flexible metal vent

G. Vent length necessary to connect elbows

H. Exhaust outlet

L Optional side exhaust outlet

Optional exhaust installations:

27" Wide Models can be converted to exhaust out the right side,

left side, or through the bottom (4-way vent kit). Each kit includes

step-by-step instructions. For ordering information, see "Venting

Kits."

®

Fire Hazard

Cover unused exhaust holes with a manufacturer's

exhaust cover kit,

Contact your local dealer.

Failure to fellow these instructions can result in death,

fire, electrical shock, or serious injury,

B C

A, Standard rear offset exhaust installation

B. Left- or right-side exhaust installation

(27" wide models only)

C. Bottom exhaust installation (27" wide models only)

Alternate installations for close clearances

Venting systems come in many varieties. Select the type best

for your installation. Two close-clearance installations are shown.

Refer to the manufacturer's instructions.

Over-The-Top installation (also available with one offset elbow)

Periscope installation

NOTE: The following kits for close clearance alternate

installations are available for purchase.

Venting Kits

For more information, call 1-800-901-2042, or visit us

at www.applianceaccessories.com, in Canada, call

1-800-807-6777 or visit us at www.whirlpoolparts.ca.

Part Number Description

8171587RP 0-5" Metal vent periscope

4396037RP 0"-18" Metal vent periscope

4396011 RP 18"-29" Metal vent periscope

4396014 29"-50" Metal vent periscope

4392892 In-Wall metal DuraVent TM Periscope

W10470674 4-way vent kit - universal grey (27" Dryers Only)

4396028 Sure Connect TM venting kit

(over-the-top installation)

4396009RP 5' Universal connect vent, flexible dryer venting

4396010RP 6' SecureConnect TM vent, flexible dryer venting

4396013RB Dryer vent installer's kit

4396033RP 5' flexible dryer venting with clamps

4396727RP 8' flexible dryer venting with clamps

4396004 Dryer offset elbow

4396005 Wall offset elbow

4396006RW DuraSafe TM close elbow

4396007RW Through-the-wall vent cap

4396008RP 4" steel dryer venting clamps- 2 pack

8212662 Flush mounting Iouvered vent hood 4"

11

Special provisions for mobile home installations:

The exhaust vent must be securely fastened to a noncombustible

portion of the mobile home structure and must not terminate

beneath the mobile home. Terminate the exhaust vent outside.

The "Vent System Chart" provides venting requirements that

will help achieve best drying performance.

Vent System Chart

Number of Type Box/Iouvered Angled

90 °turns or of vent hoods hoods

elbows

Rigid metal 64 ft. (20 m) 58 ft. (17.7 m)

Rigid metal 54 ft. (16.5 m) 48 ft. (14.6 m)

Rigid metal 44 ft. (13.4 m) 38 ft. (11.6 m)

3 Rigid metal 35 ft. (10.7 m) 29 ft. (8.8 m)

4 Rigid metal 27 ft. (8.2 m) 21 ft. (6.4 m)

Determine vent path:

[] Select route that will provide straightest and most direct path

outdoors.

[] Plan installation to use fewest number of elbows and turns.

[] When using elbows or making turns, allow as much room

as possible.

[] Bend vent gradually to avoid kinking.

[] Use as few 90° turns as possible.

Determine vent length and elbows needed for best

drying performance:

[] Use following "Vent System Chart" to determine type of vent

material and hood combinations acceptable to use.

NOTE: Do not use vent runs longer than those specified

in "Vent System Chart." Exhaust systems longer than those

specified will:

[] Shorten life of dryer.

[] Reduce performance, resulting in longer drying times and

increased energy usage.

NOTE: Side and bottom exhaust installations for 27" wide

models have a 90° turn inside the dryer. To determine

maximum exhaust length, add one 90°turn to the chart.

_

Vent System Chart

(29" Wide Long Vent Models Only)

Number of Type Box/Iouvered, or

90 °turns of vent Angled hoods

or elbows

0 Rigid metal 120 ft. (36.6 m)

1 Rigid metal 110 ft. (33.5 m)

2 Rigid metal 100 ft. (30.5 m)

3 Rigid metal 90 ft. (27.4 m)

4 Rigid metal 80 ft. (24.4 m)

5 Rigid metal 70 ft. (21.3 m)

Install Vent System

1, Install exhaust hood

rain.

12" rnin.

(305 turn)

Install exhaust hood and use caulking compound to seal

exterior wall opening around exhaust hood.

12

f

2, Connect vent to exhaust hood

Vent must fit over the exhaust hood. Secure vent to exhaust

hood with 4" (102 mm) clamp. Run vent to dryer location

using straightest path possible. Avoid 90°turns. Use clamps

to seal all joints. Do not use duct tape, screws, or other

fastening devices that extend into interior of vent to secure

vent, because they can catch lint.

3. Open shut-off valve

c,o

pen valve

Open shut-off valve in supply line; valve is open when handle

is parallel to gas pipe. Then, test all connections by brushing

on an approved noncorrosive leak-detection solution.

Bubbles will show a leak. Correct any leaks found.

Connect Vent

Make Gas Connection

1, Connect gas supply to dryer

Flared Non-flared

male fitting male fitting

Remove red cap from gas pipe. Using a wrench to tighten,

connect gas supply to dryer. Use pipe-joint compound

on threads of all non-flared male fittings. If flexible metal

tubing is used, be sure there are no kinks.

NOTE: For LP gas connections, you must use pipe-joint

compound resistant to action of LP gas. Do not use

TEFLON ®t tape.

2. Plan pipe fitting connection

B

A. 3/8" flexible gas connector C. 3/8" to 3/8" pipe elbow

B. 3/8" dryer pipe D. 3/8" pipe-to-flare adapter fitting

A combination of pipe fittings must be used to connect dryer

to existing gas line. A recommended connection is shown.

Your connection may be different, according to supply line

type, size, and location.

1®TEFLON is a registered trademark of E.I. Dupont De Nemours and Company.

Using a 4" (102 mm) clamp, connect vent to exhaust outlet

in dryer. If connecting to existing vent, make sure vent is

clean. Dryer vent must fit over dryer exhaust outlet and inside

exhaust hood. Check that vent is secured to exhaust hood

with a 4" (102 mm) clamp.

_2, Move dryer to final location

1

J

Move dryer to final location. Avoid crushing or kinking vent.

After dryer is in place, remove corner posts and cardboard

from under the dryer.

13

Leve Dryer

Check levelness of dryer from side to side. Repeat from

front to back.

NOTE: The dryer must be level for the moisture sensing system

to operate correctly.

Not Level LEVEL Not Level

:2. Tighten and adjust leveling legs

If dryer is not level, prop up using a wood block. Use wrench

to adjust legs up or down, and check again for levelness.

Once legs are level, make sure all four legs are snug against

the floor before tightening them.

If the dryer will not start, check the following:

[] Dryer is plugged into a grounded 3-prong outlet.

[] Electrical supply is connected.

[] Household fuse is intact and tight, or circuit breaker has

not tripped.

[] Dryer door is closed.

[_ When the dryer has been running for 5 minutes, open

the dryer door and feel for heat. If you feel heat, cancel cycle

and close the door.

If you do not feel heat, turn the dryer off and check to see

whether gas supply line shut-off valve is open.

[] If the gas supply line shut-off valve is closed, open it,

then repeat the 5-minute test as outlined above.

[] If the gas supply line shut-off valve is open, contact a

qualified technician.

NOTE: You may notice an odor when the dryer is first heated.

This odor is common when the heating element is first used.

The odor will go away.

Reverse Door Swing (Optionam}

If your door is the 29" Large Side-Swing Door,

follow steps 1-6.

i

If your door is the 29" Super Wide Side-Swing Door,

follow steps 1-13.

If your door is the 27" Wide Side-Swing Door,

follow steps 1-11.

Complete mnstaHation Checklist

[_ Check that all parts are now installed. Ifthere is an extra

part, go back through steps to see what was skipped.

[_ Check that you have all of your tools.

[_ Dispose of/recycle all packaging materials.

[_ Check dryer's final location. Be sure vent is not crushed

or kinked.

[_ Check that dryer is level. See "Level Dryer."

[_ Remove film on console and any tape remaining on dryer.

[_ Wipe dryer drum interior thoroughly with a damp cloth to

remove any dust.

[_ Read "Dryer Use" in your Use and Care Guide.

[_ Set the dryer on a full heat cycle (not an air cycle) for

20 minutes and start the dryer.

14

If your door is the 27" Wide Side-Swing Door with Glass,

follow steps 1-14.

NOTE: Magnetized screwdriver is helpful.

29" Wide Model Large Side=Swing Door

1, Place towel on dryer

Place towel on top of dryer to avoid damaging the surface.

4, emove and transfer hinge

hole plugs

Use a small, flat-blade screwdriver to gently remove 4 hinge

hole plugs on left side of dryer cabinet. Insert plugs into hinge

holes on opposite side of dryer cabinet.

dryer cabinet

Open dryer door. Remove bottom screws from dryer cabinet

side of hinges. Loosen (do not remove) top screws from dryer

cabinet side of hinges.

NOTE: Two people may be needed to reinstall door.

Insert screws into bottom holes on left side of dryer cabinet.

Tighten screws halfway. Position door so large end of door

hinge slot is over screws. Slide door up so screws are in

bottom of slots. Tighten screws. Insert and tighten top

screws in hinges.

Lift door until top screws in cabinet are in large part of hinge

slot. Pull door forward off screws. Set door on top of dryer.

Remove top screws from dryer cabinet.

Close door and check that door strike aligns with door

catch. If needed, slide door catch left or right within slot

to adjust alignment.

15

Place towel on top of dryer to avoid damaging the surface.

4, Remove screws from hinges

Remove screws attaching hinges to door.

f_5, Remove screws from door

Open dryer door. Remove bottom screws from dryer cabinet

side of hinges. Loosen (do not remove) top screws from

dryer cabinet side of hinges.

Remove screws at top, bottom, and side of door (4 screws).

Keep door screws separate from hinge screws as they are

different sizes. Holding door over towel on dryer, grasp sides

of outer door and lift to separate it from inner door.

NOTE: Do not pry apart with putty knife or screwdriver.

Do not pull on door seal or plastic door catches.

6, Rotate outer door

Take outer door and rotate in 180° and set it back down on

inner door. Be certain to keep cardboard spacer centered

between doors. Reattach outer door panel to inner door

panel so handle is on the side where hinges were just

removed. Insert 4 door screws.

Lift door until top screws in dryer cabinet are in large part of

hinge slot. Pull door forward off screws. Set door (handle side

up) on top of dryer. Remove top screws from dryer cabinet.

16

7. Flip door over

\

Flip door over so handle side is down.

8, Attach door hinges

Reattach door hinges to dryer door so that the larger hole is

at the bottom of the hinge.

9. Remove door strike

Remove door strike from dryer cabinet and set aside.

_'_ 0, Remove and transfer hinge

hole plugs

Use a small, flat-blade screwdriver to gently remove 4 hinge

hole plugs on left side of dryer cabinet. Transfer plugs into

hinge holes on opposite side of dryer cabinet.

dryer cabinet

NOTE: Two people may be needed to reinstall door.

Insert screws into the bottom holes on left side of dryer

cabinet. Tighten screws halfway. Position door so large end

of door hinge slot is over screws. Slide door up so screws

are in bottom of slots. Tighten screws. Insert and tighten top

screws in hinges.

17

1 2, Remove door strike plug

Remove door strike plug. insert the door strike removed in

Step 9 into hole and secure with screw, insert door strike

plug into original door strike hole and secure with screw.

Open dryer door. Remove bottom screws from dryer cabinet

side of hinges. Loosen (do not remove) top screws from dryer

cabinet side of hinges.

Lift door off top screws

Close door and check that door strike aligns with door

catch. If it is needed, slide door catch left or right within slot

to adjust alignment.

27" Wide Model Side-Swing Door

1, Place towel on dryer

Place towel on top of dryer to avoid damaging the surface.

Lift door until top screws in dryer cabinet are in large part of

hinge slot. Pull door forward off screws. Set door (handle side

up) on top of dryer. Remove top screws from dryer cabinet.

4, Remove screws from hinges

Remove screws attaching hinges to door.

18

\

Remove screws at top, bottom, and side of door

(6 screws). Keep door screws separate from hinge screws

as they are different sizes. Holding door over towel on

dryer, grasp sides of outer door and lift to separate it

from inner door.

NOTE: Do not pry apart with putty knife or screwdriver.

Do not pull on door seal or plastic door catches.

6, Rotate outer door

Take outer door and rotate it 180° and set it back down on

inner door. Be certain to keep cardboard spacer centered

between doors. Reattach outer door panel to inner door

panel so handle is on the side where hinges were just

removed. Insert 6 door screws.

Flip door over

8, Attach door hinges

Reattach door hinges to dryer door so that the larger hole is

at the bottom of the hinge.

9, Remove and transfer plugs

Remove the 4 screws that attach 2 plugs on the left side.

Transfer plugs to opposite side using the same 4 screws.

Flip door over so handle side is down.

19

dryer cabinet

NOTE: 2 people may be needed to reinstall door.

Insert screws into the bottom holes on left side of dryer

cabinet. Tighten screws halfway. Position door so large end of

door hinge slot is over screws. Slide door up so screws are in

bottom of slots. Tighten screws. Insert and tighten top screws

in hinges.

Open dryer door. Remove bottom screws from dryer cabinet

side of hinges. Loosen (do not remove) top screws from dryer

cabinet side of hinges.

Lift door off top screws

(9

Close door and check that door strike aligns with door catch.

If it is needed, slide door catch left or right within slot to

adjust alignment.

27" Wide Model Side=Swing Door with Glass

1, Place towel on dryer

Lift door until top screws in dryer cabinet are in large part of

hinge slot. Pull door forward off screws. Set door (handle side

up) on top of dryer. Remove top screws from dryer cabinet.

\

Remove screws attaching hinges to door.

Placetowel on top of dryerto avoid damaging the surface.

20

La page charge ...

Amana NGD4600YQ0 Guide d'installation

Ce manuel convient également à

Amana NGD4600YQ0 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents