PRODIS HC410RSS Le manuel du propriétaire

Marque: PRODIS

Modèle: HC410RSS

Taper: Le manuel du propriétaire

Ce manuel convient également à

P2M070STD-Ver1.0

Instruction Manual

Bedienungsanleitung

Manuel d’utilisation

Manual de instrucciones

Manual de instruções

Istruzioni d’uso

1 P2M070STD-Ver1.0

P2M070STD-Ver1.0 2

Dear Customer,

Congratulations on your purchase of this product.

Please take a few minutes before starting operation of the appliance and read the following operating

instructions.

Table of Contents

Product Overview ............................................................................................................... 3

Safety Tips ........................................................................................................................... 4

Intended Use ...................................................................................................................... 5

Location and Installation .................................................................................................... 6

Operation ............................................................................................................................ 7

Cleaning, Care & Maintenance ......................................................................................... 11

Troubleshooting ................................................................................................................ 12

Disposal ............................................................................................................................. 13

Technical data ................................................................................................................... 14

Warranty ........................................................................................................................... 14

3 P2M070STD-Ver1.0

Product Overview

Article Description

Upright Chiller – 200Lt. / 400Lt. / 600Lt.

Upright Freezer – 200Lt. / 400Lt. / 600Lt.

P2M070STD-Ver1.0 4

Safety Tips

IMPORTANT: For your safety read the manual

carefully before installing or using this product. Save

this manual for future reference.

Consult Local and National Standards to comply with the following:

1. Health and Safety at Work Legislation

2. Fire Precautions

3. IEE Wiring Regulations

4. Building Regulations

5. DO NOT use the appliance outside.

6. DO NOT attempt to service the item yourself.

7. DO NOT use damaged appliances. If you are in any doubt, consult service

agent.

8. DO NOT use electrical appliances inside the appliance (e.g. heaters, ice-

cream makers etc.), unless they are of the type recommended by the

manufacturer.

9. Keep ventilation openings, in the appliance enclosure or in the built-in

structure, clear of obstruction.

10. DO NOT use mechanical devices or other means to accelerate the

defrosting process, other than those recommended by the manufacturer.

11. DO NOT damage the refrigerant circuit.

12. DO NOT stand or support yourself on the base, drawers or doors.

13. DO NOT allow oil or fat to come into contact with the plastic components

or door seal. Clean immediately if contact occurs.

14. This unit can be used by children aged above 8 years and persons with

reduced physical, sensory or mental capabilities or lacking of experience

and knowledge who have been given supervision or using instruction of

the device and understand the resulting risks (for European market).

15. Do not let children play with the appliance.

16. Cleaning and user maintenance must not be carried out by children

without supervision.

17. DO NOT place combustible, explosive or volatile articles, corrosive acids

or alkalis or liquids in the appliance.

5 P2M070STD-Ver1.0

Safety Tips

18. DO NOT use this appliance to store medical supplies.

19. DO NOT use jet/pressure washers to clean the appliance.

20. DO NOT allow children to play with the packaging, and dispose plastic

bags safely.

21. Bottles that contain a high percentage of alcohol must be sealed and

placed vertically in the refrigerator.

22. Always carry, store and handle the appliance in a upright orientation and

move by holding the base of the appliance.

23. Always switch off and disconnect the power supply to the unit before

cleaning.

24. If the supply cord is damaged, it must be replaced by the manufacturer,

its service agent or similarly qualified persons in order to avoid a hazard.

25. This appliance is not intended for use by persons (including children) with

reduced physical, sensory or mental capabilities, or lack of experience and

knowledge, unless they have been given supervision or instruction

concerning use of the appliance by a person responsible for their safety

(for market beyond European).

26. Children should be supervised to ensure that they do not play with the

appliance.

27. For indoor use only. Not suitable for installation in an area where a water

jet could be used. Shall not be cleaned by a water jet.

28. To guarantee safe operation, ensure that the appliance is set up and

connected as described in the instruction manual.

29. Any repairs and work on the appliance should only be carried out by the

customer service department/ qualified technician.

30. The key to the electrical cabinet should be kept out of the reach of

children and users.

31. Do not store explosive substances such as aerosol cans with a flammable

propellant in this appliance.

Intended Use

Only use this appliance for cooling and storage of food and beverage for commercial purposes.

P2M070STD-Ver1.0 6

Location and Installation

 Remove the appliance from the packaging. Make sure that all protective plastic film and coatings are

thoroughly removed from all surfaces. To prevent injury or damage to the unit, we recommend that the

appliance should be unpacked and set up by two people.

 The climatic class can be found on the rating plate. It specifies the ambient temperatures at which the

appliance may be operated. The rating plate can be found inside the appliance.

Climate Class

Max. Ambient Temperature

Relative Humidity

60%

55%

40%

 Maintain a distance of 20 cm (7 inches) between the appliance and walls or other objects for ventilation.

Increase this distance if the obstacle is a heat source.

 The appliance should be placed on a solid flat and stable floor to reduce noise and vibration. Level the

appliance by adjusting the feet.

 Avoid locating the unit in direct sunlight or near heat sources such as ovens or radiators.

 Please make sure the appliance is properly ventilated.

 Check that the power supply and voltage used comply with the details on the rating plate. The plug

must be accessible after installation.

 Correctly connect and disconnect the plug. When inserting ensure the plug is fully engaged. While

unplugging hold the body of the plug. Never pull the supply cord directly.

 If the unit is to be shut down for long period, switch it off and disconnect the plug from socket outlet.

Clean the appliance and leave the door open to prevent odour.

 Important! For your personal safety, this appliance must be properly grounded (earthed). This

appliance is equipped with a cord having a grounding wire with a grounding plug. The plug must be

inserted into an outlet that is properly grounded and installed. Consult a qualified electrician or service

centre if you do not completely understand the grounding instructions. If doubt exits whether the

appliance is properly grounded, have a qualified electrician check the circuit to make sure the outlet is

properly grounded.

 If the cable does not reach the nearest socket, either rearrange your store layout or ask a qualified

electrician to fix a new socket.

 If power is cut off, wait for at least 3 minutes before restarting the appliance to avoid damaging the

compressor.

 Slide the shelf/drawer into place.

Note: If the unit has not been stored or moved in an upright position, let it stand upright for

approximately 12 hours before operation.

Note: Before using the appliance for the first time, clean the shelves and interior with soapy water.

7 P2M070STD-Ver1.0

Operation

Turn on

 Close the door of the appliance.

 Plug in the cabinet.

 The display shows the actul cabinet temperature.

P2M070STD-Ver1.0 8

Operation

Temperature Setting and Control (Dixell)

 The front panel of the thermostat

display:

1. Defrost-/ Light Key (Light key only

active in glass door models)

2. SET Key

3. UP- Key

4. Stand By-/ DOWN Key

LED

Mode

Function/ Explanation

Compressor Operation Indicator

Flashing

Compressor Start Delay Indicator

Defrost enabled

Flashing

Drip time in progress

Fan Operation Indicator

Flashing

Fan Delay Indicator (After Defrost)

Alarm Indicator

Light Indicator (active on glass door)

Measurement Unit Indicator

Flashing

Programming Mode

Stand By Mode (Compressor OFF, Light and

fan function with normal operation)

How to switch the unit from Stand By Mode to ON mode / How to switch the unit from ON Mode to Stand By mode

• Press and hold the Standby key for 3s.

How to see the set point

• Push and immediately release the key, the set point is displayed.

• Push and immediately release the key or wait about 15s to return to normal visualisation.

How to change the set point

• Push the key for more than 2 seconds to change the set point value

• The value of the set point will be displayed and the “ ” starts blinking

• To change the set value push the “ “ (up) or “ ” (down) arrows within 15s.

• To memorise the new set point push the key again or wait for 15s.

Automatic defrost

• The appliance will automatically run defrost cycles.

Note: The defrost timer starts from the time the appliance is initially powered up.

Manual Defrost:

• Press and hold the “ ” DEFROST button for 5s.

• The defrost cycle will start immediately and the Defrost LED illuminates.

Note: Starting a manual defrost resets as well the automatic defrost timer.

How to turn ON / OFF the light

• Press and release the key, to switch the light ON or OFF.

Note: Light function is active only for glass door models.

How to see recorded MINIMUM and MAXIMUM temperatures

• Press and release the “ “ or “ ” key. The recorded MIN (“Lo”)/MAX (“Hi”) temperature of the last 24h is displayed.

• To reset the record press for 3s while the MIN or MAX temperature is displayed.

How to Lock and Unlock the keyboard

• Press both “ “ and “ ” key at the same time for more than 3s. The display shows “PoF”/ “Pon” to indicate that the keyboard is

locked/ unlocked.

Alarm Code Description:

• P1 – Room probe failure, P2 – Evaporator probe failure, HA – Max.temperature alarm, LA – Min. temperature Alarm, H2 – Max.

temperature alarm 3rd Probe, L2 – Min temperature alarm 3rd probe, EA – External Alarm, CA – Serious external alarm, dA – Door open

alarm, HF – Defrost alarm.

9 P2M070STD-Ver1.0

Operation

Temperature Setting and Control (Dixell)

 The front panel of the thermostat display:

1. Defrost indicator

2. Compressor operation indicator

3. SET key

4. Temperature modification keys

5. Defrost button

How to see the set point

• Push and immediately release the SET key, the set point will be showed;

• Push and immediately release the SET key or wait about 15s to return to normal visualisation.

How to change the set point

• Push the SET key for more than 2 seconds to change the set point value;

• The value of the set point will be displayed and the “°C” starts blinking;

• To change the set value push the „ “ (up) or “ ” (down) arrows within 15s.

• To memorise the new set point value push the SET key again or wait 15s.

Automatic defrost

• The appliance will automatically run defrost cycles.

Note: The cycle starts from the time the appliance is initially powered up.

Manual Defrost:

• Press and hold the DEFROST button for 5 seconds.

• The defrost cycle will start immediately and the Defrost LED illuminates.

Note: Starting a manual defrost also resets the automatic defrost timer.

P2M070STD-Ver1.0 10

Operation

How to reverse the door

11 P2M070STD-Ver1.0

Cleaning, Care & Maintenance

Routine maintenance

Switch off and disconnect from the power supply before cleaning.

 Clean the enclosure and interior of the appliance as often as possible.

 Clean the unit with moist cloth. Never allow the switch, control panel, cable or plug to get wet.

 Do not use abrasive cleaning agents. These can leave harmful residues. Use only mild soapy water.

 Clean the door seal with water only.

 Ensure that no cleaning water penetrates into the electrical components.

 Must not be cleaned by a water jet.

 Always wipe dry after cleaning with soft cloth.

 Do not allow water used in cleaning to run through the drain hole into the evaporation pan.

 Take care when cleaning the rear of the appliance.

 An agent or technician must carry out repairs if required.

 If the appliance is to be left inactive for long periods, unplug the appliance after having turned the

switch to OFF position, empty the refrigerating compartment and clean thoroughly.

Special maintenance

The instructions given in the following paragraph can be followed from qualified technicians

 Periodically clean the condenser using suitable tools (vacuum cleaner or soft brushes) can extend

the life of the appliance.

 Check that the electrical connections are not loose.

 Check that the thermostat and the sensor are in proper working order.

P2M070STD-Ver1.0 12

Troubleshooting

Fault

Potential Failure

Problem solving action

The appliance is not

working

The unit is not switched on

Check the unit is plugged in correctly and

switched on

Plug and/ or lead are damaged

Call your agent or qualified technician

Fuse in the plug has blown

Replace the fuse (UK Plug)

Power supply

Check power supply

The appliance turns

on, but the

temperature

is too high/ low

Too much ice on the evaporator

Defrost the appliance

Condenser blocked with dust

Call your agent or qualified technician

Doors are not shut properly

Check doors are shut and seals are not

damaged

Appliance is located near a heat

source or air flow to the condenser is

being interrupted

Move the refrigerator to a more suitable

location

Ambient temperature is too high

Increase ventilation or move appliance to

a cooler position

Unsuitable foodstuffs are being

stored in the appliance

Remove any excessive hot foodstuffs or

blockages to the fan

Appliance is overloaded

Reduce the amount of food stored in the

appliance

The appliance is

unusually loud

Loose nut/ screw

Check and tighten all nuts and screws

The appliance has not been installed

in a level or stable position

Check installation position and change if

necessary

The appliance is

leaking water

The appliance is not properly leveled

Adjust the screw feet to level the

appliance (if applicable)

The discharge outlet is blocked

Clear the discharge outlet

Movement of water to the drain is

obstructed

Clear the floor of the appliance (if

applicable)

The water container is damaged

Call your agent or qualified Technician

The drip tray is overflowing

Empty the drip tray (if applicable)

13 P2M070STD-Ver1.0

Disposal

If the appliance is no longer of use and you wish to dispose of it, remove doors to prevent any small child

from be trapped inside. Then please do in an environmentally correct way.

Contact a qualified service technician:

1. To recover all Freon/refrigerant

2. To remove the compressor or remove the oil from the compressor

3. To remove the flammable insulation blowing gases

Then the distributor/ retailer can contact their local metal recycling center to pick up the remaining cabinet,

shelves, etc.

There may be special requirements or conditions. You can obtain information on the disposal of

refrigeration appliances from:

 Your supplier

 Government authorities (The local council, Ministry of the Environment, etc.)

By law, disposal of hazardous wastes may be subject to fines and imprisonment under the provisions of the

environmental regulations.

1. The refrigerant of this unit is a hydrocarbon refrigerant and is covered by the Kyoto Protocol.

2. Releasing the refrigerant to the atmosphere will harm the environment by contributing to the

global warming. The Global Warming Potential (GWP) of R134a is 1430, of R404a is 3922, of

R600a/R290 is 3.

Disposal

Discarded electric appliances are recyclable and should not be discarded in the domestic

waste! Please actively support us in conserving resources and protecting the

environment by returning this appliance to the collection centres (if available).

Dispose of packaging in accordance to applicable legal regulations.

P2M070STD-Ver1.0 14

Technical data

Model

Upright Chiller / Freezer – 200Lt. / 400Lt. / 600Lt.

Climate Class

Please refer to the information indicated on the product. You will find

the information on the rating label on the back of the unit as well as

inside the cooling compartment. The circuit diagram is displayed on the

back of the unit as well as inside the cooling compartment

Refrigerant Gas

Refrigerant Charge

Temperature Range (°C)

Input Power

Rated Frequency

Rated Voltage

Internal volume

Net Weight

Gross Weight

Foaming Agent

External Dimension (mm)

CAUTION: RISK OF FIRE AND EXPLOSION WITH FLAMMABLE

REFRIGERANT R600a/R290.

Warranty

A statutory warranty applies for this product.

Damages caused by wrong treatment or operation, by false placement or storage, improper connection or

installation, as well as force or other external influences are not covered by this warranty. We recommend

careful reading of the operating instructions as it contains important information.

Note:

1. In case this product does not function correctly, please firstly check if there are other reasons, e.g. for

electrical appliances interruption of the power supply, or generally incorrect handling are the cause.

2. Please note that, where possible, the following documents or rather information should be provided

together with your faulty product:

 Purchase receipt

 Model description/ Type/ Brand

 Describe the fault and problem as detailed as possible

In the case of a claim for guarantee or defects, please contact the seller.

GWL 8/14 EN

15 P2M070STD-Ver1.0

P2M070STD-Ver1.0 16

Übersetzung der Originalbetriebsanleitung

Sehr geehrte Kundin,

sehr geehrter Kunde,

herzlichen Glückwunsch zum Kauf dieses Produktes.

Bitte nehmen Sie sich einige Minuten Zeit, bevor Sie das Gerät in Betrieb nehmen und lesen Sie die

nachfolgende Gebrauchsanweisung durch.

Inhaltsverzeichnis

Produktübersicht .............................................................................................................. 17

Sicherheitshinweise .......................................................................................................... 18

Bestimmungsgemäßer Gebrauch ..................................................................................... 20

Platzierung und Installation .............................................................................................. 21

Funktion und Handhabung ............................................................................................... 22

Reinigung, Pflege und Wartung ........................................................................................ 26

Fehlerbehebung ................................................................................................................ 27

Entsorgung ........................................................................................................................ 28

Technische Daten ............................................................................................................. 29

Gewährleistung ................................................................................................................. 29

17 P2M070STD-Ver1.0

Produktübersicht

Article Description

Kühlschrank – 200Lt. / 400Lt. / 600Lt.

Gefrierschrank – 200Lt. / 400Lt. / 600Lt.

P2M070STD-Ver1.0 18

Sicherheitshinweise

WICHTIG: Lesen Sie diese Anleitung zu Ihrer persönlichen Sicherheit

sorgfältig durch, bevor Sie das Gerät installieren oder in Betrieb

nehmen. Bewahren Sie die Anleitung gut auf, um jederzeit darauf

zurückgreifen zu können.

In den folgenden Punkten muss das Gerät die landesüblichen Vorschriften

erfüllen:

1. Gesundheit und Sicherheit am Arbeitsplatz

2. Brandschutzbestimmungen

3. IEE-Vorschriften für elektrische Leitungen

4. Bauordnung

5. Verwenden Sie das Gerät NIEMALS im Freien.

6. Führen Sie NIEMALS eigenhändig Wartungsarbeiten an diesem Gerät

durch.

7. Verwenden Sie das Gerät NICHT, wenn es Beschädigungen aufweist.

Wenden Sie sich im Zweifel an Ihren Kundendienst.

8. Verwenden Sie unter keinen Umständen weitere elektrische Geräte im

Inneren dieses Gerätes (z.B. Heizgeräte, Eismaschinen - es sei denn, diese

sind vom Hersteller ausdrücklich erlaubt).

9. Halten Sie die Ventilationsöffnungen im Inneren des Geräts oder in der

eingebauten Struktur frei und vermeiden Sie Blockierungen des

Luftstroms.

10. Versuchen Sie unter keinen Umständen, mechanisch oder mit einem

anderen Hilfsmittel den Abtauvorgang zu beschleunigen (es sei denn, es

wurde vom Hersteller ausdrücklich genehmigt).

11. Beschädigen Sie NIEMALS den Kältekreislauf des Gerätes.

12. Stellen Sie sich NICHT auf das Gerät, die Regale oder die Türen des

Gerätes und halten Sie sich NICHT daran fest.

13. Achten Sie darauf, dass Kunststoffkomponenten oder die Türdichtungen

NICHT mit Öl oder Fett in Kontakt kommt. Sollte dies dennoch passieren,

reinigen Sie die Dichtung umgehend.

19 P2M070STD-Ver1.0

Sicherheitshinweise

14. Dieses Gerät kann von Kindern über 8 Jahren sowie von Personen mit

verringerten physischen, sensorischen oder mentalen Fähigkeiten oder

Mangel an Erfahrung und Wissen benutzt werden, wenn sie beaufsichtigt

oder bezüglich des sicheren Gebrauchs des Gerätes unterwiesen wurden

und die daraus resultierenden Gefahren verstehen.

15. Lassen Sie Kindern nicht mit dem Gerät spielen.

16. Reinigung und Wartung dürfen nicht von Kindern ausgeführt werden, die

unbeaufsichtigt sind.

17. Platzieren Sie NIEMALS brennbare, explosive oder leicht verdampfbare

Gegenstände, Ätzmittel, Alkali oder andere Flüssigkeiten in das Gerät.

18. Lagern Sie in diesem Gerät unter keinen Umständen medizinische

Substanzen.

19. Reinigen Sie das Gerät NIEMALS mit einem Hochdruckreiniger.

20. Kinder dürfen nicht mit dem Verpackungsmaterial spielen. Entsorgen Sie

Plastikbeutel vorschriftsgemäß.

21. Flaschen mit hochprozentigem Alkohol müssen verschlossen sein und

aufrecht in das Gerät gestellt werden.

22. Tragen, lagern und betreiben Sie das Gerät immer in aufrechter Position.

Fassen Sie das Gerät immer am Sockel an, wenn sie es bewegen wollen.

23. Bevor Sie das Gerät reinigen, müssen Sie das Gerät immer ausschalten

und den Netzstecker ziehen.

24. Wenn das Stromkabel dieses Gerätes beschädigt wird, muss sie durch den

Hersteller, seinen Kundendienst oder eine ähnlich qualifizierte Person

ersetzt werden, um Gefahren zu vermeiden.

25. Dieses Gerät darf nicht von Personen mit eingeschränkten physischen,

sensorischen oder mentalen Fähigkeiten, Personen mit fehlender

Erfahrung und Wissen sowie nicht von Minderjährigen betrieben werden,

es sei denn diese stehen unter Aufsicht oder erhalten Anweisungen von

einer für deren Sicherheit verantwortlichen Person.

26. Kinder müssen beaufsichtigt werden, um sicherzustellen, dass sie nicht

mit dem Gerät spielen.

27. Das Gerät ist nur für den Innengebrauch konzipiert. Nicht geeignet zur

Installation in einem Bereich, in dem ein Hochdruckreiniger verwendet

werden könnte.

La page charge ...

PRODIS HC410RSS Le manuel du propriétaire

Marque: PRODIS

Modèle: HC410RSS

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

italiano: PRODIS HC410RSS Manuale del proprietario
español: PRODIS HC410RSS El manual del propietario
Deutsch: PRODIS HC410RSS Bedienungsanleitung
português: PRODIS HC410RSS Manual do proprietário

PRODIS HC410RSS Le manuel du propriétaire

Ce manuel convient également à

PRODIS HC410RSS Le manuel du propriétaire

dans d''autres langues

Autres documents