Dometic Heki 2 Skylights H2DOM1127XXXX Guide d'installation
- Taper
- Guide d'installation
1
RECORD THIS UNIT INFORMATION FOR
FUTURE REFERENCE:
Model Number
Date Purchased
SERVICE OFFICE:
USA
Dometic, LLC
2320 Industrial Pkwy
Elkhart, IN 46516
574-294-2511
CANADA
Dometic, LLC
46 Zatonski, Unit 3
Brantford, ON N3T 5L8
CANADA
519-720-9578
For Service Center
Assistance Call:
800-544-4881
INSTALLATION INSTRUCTIONS H2DOM1127XXXX
Form No. 3312722.000 2008-07
©2008 Dometic, LLC
LaGrange, IN 46761
This manual must be read and
understood before installation,
adjustment, service, or mainte-
nance is performed. This unit must
be installed by a qualifi ed service
technician. Modification of this
product can be extremely hazard-
ous and could result in personal
injury or property damage.
Lire et comprendre ce manuel avant
de procéder à l’installation, à des ré-
glages, de l’entretien ou des répara-
tions. L’installation de cet appareil doit
être effectuée par un réparateur quali-
fi é. Toute modifi cation de cet appareil
peut être extrêmement dangereuse et
entraîner des blessures ou dommages
matériels.
HEKI 2 SKYLIGHTS
H2DOM1127XXXX (HEKI 2)
H2DOM1127 DOM1127
H2DOM H2XDOM
Installation instructions HEKI 2 (lift/tilt roof-light)
1) Designed and recommended for trailed vehicles in which people do not travel. Technically
also suited to a vehicle in which people do travel, but as the rooflight is designed with free
airflow, there may be draughts, air noise and chattering blind mechanisms, which will not be
accepted as a product fault.
2) HEKI 2 suitable for max. 62 mph [100 km/h] (with Seitz spoiler up to 80 mph [130 km/h]).
3) Installation position transverse (hinged side at the front in the travelling direction) or
longitudinal (hinged side to the left or right in the travelling direction).
Before installing HEKI 2, the area where it is to be installed must be selected in such a way
that HEKI 2 will not impair any adjacent components, cables or fitted cupboards in the
vehicle interior, or detract from the fu nctions of the roof railing or o ther fastening or
reinforcing components. Prerequisite fo r correct installation of HEKI 2 is a flat inner and
o uter wall surface. In order to avoid any damage to the roof wall, the cut-out must be robust
(e.g. reinforced with wooden or tubular frames incl. corners). HEKI 2 is suitable fo r wall
thickness between 31/32" [25mm] and 2 3/8" [60mm].
W e cannot assume any guarantee fo r faulty installation of HEKI 2.
1. Ascertain the position of HEKI 2 in the vehicle according to the conditions named above.
2. Proceed with the cut-out according to fig. 2 or using the template on the packaging, using a
jig saw or routing machine.
HEKI 2 is ready fo r installatio n in wall thicknesses of 31/32" [25mm] to 1 1/4" [32 mm]. (For
wall thicknesses of 1 1/4" [32mm] to max. 2 3/8" [60mm], the commercially available instal-
lation set must be used, please consult your dealer).
2
3. Hold HEKI 2 in the cut-out without any sealant, to check the size (approx. 1/16" [2mm]
clearance fo r cut out all round).
4. Apply permanently elastic sealant (butyl) to the outer part of the base frame. We
recommend contacting your sealant supplier (fig. 3).
5. Position the outer frame centrally in the cut-out and press in position applying gentle, even
pressure.
3
2 9/16 inches
37 25/32 inches
25 25/32 inches
Glass
Outer frame
Mounting blocks
Outer frame
6. Gently screw the 16 mounting blocks to the inside of the vehicle (use the large hole spacing
in the mounting block). Use the mounting blocks and appropriate screws indicated in the table
below for the corresponding roof thickness.
It is adequate to tighten the screws gently by hand (torque = 13 in-lb [1.5 Nm]). If necessary,
re-tighten the mounting blocks again uniformly after approx. 10- 30 minutes.
Wall Thickness Mounting Block Screws
25-32mm grey 4x25mm
32-39mm black 4x32mm
39-46mm yellow 4x40mm
46-53mm blue 4x46mm
53-60mm red 4x52mm
7. Position the inner frame on the base frame and screw in place using the corresponding
screws 2.5 x 25mm (use small hole diameter in mounting block).
It is adequate to tighten the screws gently by hand!
Check blind function! Undo the screws slightly when the blind moves sluggishly.
8. Snap the ventilation grids into position.
9. Remove the PE protective film from the acrylic glass on the inside and outside.
No liability is assumed for incorrect installation!
HEKI 2 is not suitable for installation in vertical surfaces!
Arrange for the modification to be entered in the vehicle's papers! (When vehicle height and
overall weight have been changed).
4
Ventilation grids
31/32" - 1 1/4"
1 1/4" - 1 17/32"
1 17/32" - 1 13/16"
1 13/16" - 2 3/32"
2 3/32" - 2 3/8"
-
1
-
2
-
3
-
4
Dometic Heki 2 Skylights H2DOM1127XXXX Guide d'installation
- Taper
- Guide d'installation
dans d''autres langues
Documents connexes
-
Dometic Midi Heki Style Mode d'emploi
-
-
Dometic Mini Heki Style Roof Light Manuel utilisateur
-
-
-
-
-
-
-