Kenmore Elite CSV Mode d'emploi

Catégorie
Aspirateurs
Taper
Mode d'emploi
Use & Care Guide
Manual de Uso y Cuidado
Manuel d'entretien et d'utilisation
Model/Modelo/Modèle: DS4095
CSV|Max
Cordless Stick Vacuum with
EasyReach Wand
Aspiradora vertical inalámbrica
con vara EasyReach
Aspirateur Balai Sans Fil Doté
D’Un Tube-Rallonge EasyReach
www.kenmorefloorcare.com
Vacuum Cleaner Help Line:
1-877-531-7321 (US) / 1-844-608-3081 (CA)
8:00am-5:00pm EST, M-F
- 2 -
Before Using Your New Vacuum Cleaner ........................................................................ 2
Packing List ..................................................................................................................... 2
Important Safety Instructions ........................................................................................3-4
Vacuum Cleaner Warranty .............................................................................................. 5
Parts and Features ........................................................................................................6-8
Assembly Instructions ................................................................................................. 9-10
Operating Instructions ................................................................................................11-12
Vacuum Maintenance and Care ................................................................................. 13-16
Troubleshooting ......................................................................................................... 17-18
Requesting Assistance Or Service .....................................................................Back Cover
TABLE OF CONTENTS
PACKING LIST
Your KENMORE ELITE CORDLESS VACUUM CLEANER is packaged with the following
parts and components assembled separately in the carton:
1 Hand Vacuum
1 Motorized Nozzle
1 Wand
1 Combination Tool
Read this Use & Care Guide. It will help you assemble and operate your new Kenmore
vacuum cleaner in the safest and most effective way.
For more information about vacuum cleaner care and operation, call the Vacuum Cleaner
Help Line at 1-877-531-7321 (US) / 1-844-608-3081 (CA). You will need the complete model
and serial numbers when requesting information.
Your vacuum cleaner’s model and serial numbers are located on the Model and Serial
Number Plate. Use the space below to record the model number and serial number of your
new Kenmore vacuum cleaner.
Model No.____________________________________________
Serial No. ____________________________________________
Date of Purchase ______________________________________
Keep this book and your sales check (receipt) in a safe place for future reference.
BEFORE USING YOUR NEW VACUUM CLEANER
1 Wall Mountable Bracket
2 Screws
1 Charging Adapter
1 Manual
- 3 -
WARNING!
READ ALL INSTRUCTIONS IN THIS GUIDE BEFORE ASSEMBLING OR USING YOUR
VACUUM CLEANER. To reduce the risk of fire, electrical shock, injury to persons or damage
when using your vacuum cleaner, follow all safety precautions listed below.
IMPORTANT SAFETY INSTRUCTIONS
Use your vacuum only as described in this
Use & Care Guide.
Do not use or charge outdoors or on wet
surfaces.
Do not allow to be used as a toy. Close
attention is necessary when used by or
near children, pets or plants.
Use only manufacturer’s recommended
attachments. Do not use attachments
other than those supplied with this
vacuum.
Do not handle charger, including charger
plug, and charger terminals with wet
hands.
Do not put any object into openings. Do
not use with any opening blocked; keep
free of dust, lint, hair, and anything that
may reduce air flow.
Keep hair, loose clothing, fingers, and all
parts of body away from openings and
moving parts.
Use extra care when cleaning on stairs.
Do not use to pick up flammable or
combustible liquids, such as gasoline, or
use in areas where they may be present.
Switch off the appliance before
connecting the accessories.
Do not pick up anything that is burning or
smoking, such as cigarettes, matches, or
hot ashes.
Do not pick toxic solution such as chlorine
bleach, ammonia or drain cleaner.
Do not use without dust cup and HEPA
filter in place.
Do not charge the unit outdoors.
Prevent unintentional starting. Ensure
the product does not operate before
connecting to hand vacuum, picking up
or carrying the appliance.
Do not attempt to charge the appliance
with the switch in the on position.
Do not attempt to use this charging
adapter with any other product nor
attempt to charge this product with
another charging adapter.
To recharge vacuum, use only Yinli
YLS0241A-T256080 or Xdroid XZ2560-
0800EU charger adapter.
Do not use an appliance that is damaged
or modified. Damaged or modified
appliance may exhibit unpredictable
behavior resulting in fire, explosion or risk
of injury.
Do not immerse vacuum cleaner, or
charging adapter in water or other
liquids.
Always turn the vacuum off before
connecting or disconnecting the
motorized nozzle.
Store the cordless vacuum indoors. Put
the cordless vacuum away after use to
prevent accidents.
Keep your work area well lit.
Keep the vacuum moving over the carpet
surface at all times to avoid damaging
the carpet fibers.
Do not vacuum up any liquids.
Do not use in an enclosed space where
vapors are present from paint, paint
thinner, moth-proofing substances,
flammable dust or other explosive or
toxic materials.
- 4 -
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
Household use only.
Do not pick up hard or sharp objects such
as glass, nail, screws or coins that could
damage the vacuum cleaner.
To avoid excessive heat and damage
to unit or batteries, do not operate the
vacuum while charging.
Do not use extension cords or outlets with
inadequate current carrying capacity.
Do not expose an appliance to fire or
excessive temperature. Exposure to fire
or temperature above 265°F (130°C) may
cause explosion.
Leaks from battery cells can occur
under extreme usage or temperature
conditions. If the liquid gets on skin, wash
quickly with water. If liquid gets into the
eyes, flush them immediately with clean
water for a minimum of 10 minutes. Seek
medical attention.
While there is no shock hazard from
electrical terminals located on the
vacuum, a burn could result from metal
objects being inserted into the terminal
areas. Vacuum cleaner terminals should
always be kept free of objects.
Store charger indoors in a cool, dry
area, not exposed to weather to avoid
electrical shock and/or damage to the
vacuum cleaner.
Changes or modifications to this unit
not expressly approved by the party
responsible for compliance could void the
user’s authority to operate the equipment.
Charging improperly or at temperatures
outside of the specified range may
damage the battery and increase the risk
of fire.
You are responsible for making sure
that your vacuum cleaner is not used
by anyone who is unable to operate it
properly.
Have servicing performed by a qualified
repair person using only identical
replacement parts. This will ensure that
the safety of the product is maintained.
Do not modify or attempt to repair
the appliance or the battery pack (as
applicable) except as indicated in the
instructions for use and care.
This appliance is designed for household
use only!
NOTICE
This device complies with part 15 of the
FCC Rules. Operation is subject to the
following two conditions.
1. This device may not cause harmful
interference.
2. This device must accept any interference
received, including interference that may
cause undesired operation.
Product Disposal
This product contains an internal Lithium-
ion battery pack formulated from
environmentally sensitive materials. This
product must be disposed of properly
with due care for the environment. Do
not dispose of product with household
garbage. Consult your local waste
authority for information regarding
available recycling or disposal options.
- 5 -
VACUUM CLEANER WARRANTY
LIMITED WARRANTY
FOR ONE YEAR from the date of sale this product is warranted against defects in
material or workmanship.
WITH PROOF OF SALE a defective product will be replaced free of charge.
The Kenmore brand is used under license. Direct all claims for warranty service to:
1-877-531-7321 (US) / 1-844-608-3081 (CA).
This warranty does not cover filters or belts, which are expendable parts that can wear
out from normal use within the warranty period.
This warranty is void if this product is ever used for other than private household purposes.
This warranty gives you specific legal rights, and you may also have other rights which
vary from state to state.
Cleva North America, Inc., Greenville SC 29607
- 6 -
PARTS AND FEATURES
It is important to know your vacuum cleaners parts and features to assure its proper and
safe use. Review these before using your vacuum.
REPLACEMENT PARTS
To order a replacement
part, call
1-877-531-7321 (US) /
1-844-608-3081 (CA).
Item Part No.(US) Part No.(CA)
HEPA Media Filter 561051107 561051107
Pre-Filter Basket 561057103 561057103
Brush Roll 571018102 571018102
2-in-1 Combination Tool 561051104 561051104
Wall Mountable Bracket 571018103 571018103
Screw (2) 551001122 551001122
Charging Adapter 561087101 561087101
- 7 -
PARTS AND FEATURES
Hand Vacuum
2-in-1 Combination Tool
Screw (2)
Motorized Nozzle
Charging Adapter
Wand
Wall Mountable Bracket
- 8 -
The motorized nozzle and the combination
tool can be inserted into either the hand
vacuum or the wand. You will hear a
click if the motorized nozzle is installed
correctly.
Combination Tool
The combination brush can be used as a
crevice tool or as a dusting brush. To use
as a dusting brush, simply squeeze the
buttons in the side of the tool and shift
brush forward.
Friction Hold Stoppers
The back of the hand vacuum features
two rubber stoppers. When you lean the
stick vac against a wall, the stoppers help
prevent the unit from slipping down and
possibly being damaged.
NOTE: For proper electrical contact,
always be sure that metal contact surfaces
of the motorized nozzle, the wand and the
hand vacuum are clean before use.
PARTS AND FEATURES
Rubber Stoppers
Crevice Tool Mode Dusting Brush Mode
- 9 -
1. Insert the hand vacuum into the top of
the wand until you hear a click.
Before assembling the vacuum cleaner, check the PACKING LIST (Page 2). Use this list to
verify that you have received all the components of your new Kenmore Elite CSV Max
Cordless Stick Vac.
ASSEMBLY INSTRUCTIONS
2. Insert the bottom of the wand into the
motorized nozzle until you hear a click.
3. Use the 2 screws provided to mount the
bracket on the wall, but not to drywall
only. Secure the screws to a stud. Mount
at a recommended height of 59'' and
no less than 44'' above the floor. Ensure
that no plumbing or electrical cables,
wires or ductwork are located directly
behind the mounting area.
4. Hang the hand vacuum on the wall
mount. Align the base of the hand
vacuum with the wall mount and slide in
as shown in the picture below.
Click
Click
NOTE: To be able to charge vacuum
while it is mounted, attach bracket to wall
no more than 59'' from wall electrical
outlet.
59”
(Recommended)
44”
(Minimum)
- 10 -
1. Insert the charging adapter plug into the
charging port on the side of the hand
vacuum base.
2. Plug the adapter into a wall outlet. The
battery indicator will begin to pulse
blue.
WARNING
Before charging make sure the unit is
turned OFF.
CHARGING
NOTE: The unit can be charged while it is
hung on the wall mountable bracket. Attach
bracket to wall no more than 59'' from a
wall electrical outlet.
NOTE: Before using stick vacuum for the
first time, charge vacuum to full capacity.
NOTE: If the battery indicator does not
illuminate when charging, ensure that the
charging adapter is plugged in properly to
the wall outlet and the charging port on the
hand vacuum.
For better battery performance, it is
recommended to charge the unit when
the battery indicator shows a continuous
yellow light during operation, and remove
the charging adapter from the unit after the
battery is fully charged.
Never charge the batteries in temperatures
above 104°F (40°C) or below 39.2°F (4°C).
It is normal for the charger to become
warm when charging.
Battery Indicator
The battery requires approximately 4 hours
of charging to regain full capacity. While
the unit is charging, the battery indicator
ring will pulse blue. When the battery is
fully charged, the battery indicator will
show a continuous blue light, and turn off
after 15 minutes.
59”
(Maximum)
- 11 -
CAUTION
Moving parts! To reduce the risk of personal injury, DO NOT
touch the brush roll when vacuum is on. Contacting the brush
roll while it is rotating can cut, bruise or cause other injuries.
Always turn off before servicing. Use caution when operating
near children or pets.
OPERATING INSTRUCTIONS
CONTROL BUTTONS
The on/off trigger button is located on
the inner side of the hand vacuum handle.
The vacuum has two-speed controls, ECO
and HIGH. Change speed by pressing the
speed change button shown below.
Battery Power Level Indicator
The battery power level indicator lights up
to give you an idea of how much battery
power remains at any given time.
NOTE: Please remove the battery
indicator label before first use.
CAUTION
Operate the appliance at room
temperature between 39.2°F (4°C) and
104°F (40°C) in order to ensure safe and
normal function.
VACUUM OPERATION
Before vacuuming floors, connect the
motorized nozzle to the wand. Then
connect the hand vacuum to the wand. The
motorized nozzle can be used for cleaning
On/Off
Button
Speed
Change
Button
carpets or rugs, as well as hard floors.
Battery Power Level
Indicator Battery Capacity
Blue, Continuous
75%~100%
Green, Continuous 50%~74%
Yellow, Continuous 25%~49%
(Recharge
recommended)
Red, Continuous 10%~24%
Red, Flashing 0~9%
(Recharge required)
- 12 -
Flex
Wand
Button
CLEANING WITH THE HAND VACUUM
To start the vacuum, press the on/off trigger
button. Once turned on, the battery level
indicator will be lit.
The vacuum starts in the ECO speed
position. To switch the speed to HIGH, press
the speed change button. Press the speed
change button again to switch back to ECO
speed.
To turn the vacuum off, press the on/off
trigger button again.
When vacuuming on plush carpet, use ECO
mode for best performance.
NOTE: When battery power decreases
to about 10% remaining, the battery level
indicator will start red flashing. The flashing
will continue until the unit is charged or is
completely out of battery power.
USING THE EASYREACH WAND
In order to easily access hard-to-reach
areas under furniture without having to
bend down, press the flex wand button to
position the wand into a lower angle.
To take the vacuum back to the straight
position, lift up the handheld vacuum. Once
straightened, the wand will lock in place.
VACUUM OPERATION
2. Install the combination tool onto the end
of the hand vacuum.
3. When finished cleaning, turn the hand
vacuum OFF and remove the combination
tool.
Wand Release Button
Easily clean messes on furniture, upholstery,
stairs and other hard-to-reach areas with
the included combination tool.
1. To detach the hand vacuum, press the
wand release button and pull the wand
from the hand vacuum.
2. Close dust cup lid until you hear a click.
NOTE: For optimal performance, please
check and clean the HEPA Media filter
regularly.
WARNING: Do not operate vacuum
cleaner without filters in place.
1. With one hand grasped around the
handle, press the filter release button to
separate the dust cup and filters from
the hand vacuum.
VACUUM MAINTENANCE AND CARE
CAUTION
To reduce the risk of electric shock, remove the charging adapter from the unit, and
make sure the unit is turned off before any maintenance.
EMPTYING DUST CUP AND CLEANING FILTER
Dust Cup Emptying
For best performance, empty dust cup
after every use or once dust reaches max
fill line. Never operate the vacuum cleaner
without dust cup and filter in place.
Before emptying the dust cup, ensure the
vacuum is turned off.
1. Position dust cup lid area of vacuum
over a waste receptacle. Press down the
dust cup release latch to open dust cup
lid and allow cup contents to drop into
waste receptacle.
Filter Cleaning
If there is hair wrapped or blocked in the
dust cup or the suction power is weak,
it is necessary to wash the HEPA media
filter and pre-filter basket to clean off
accumulated dust or hair.
- 13 -
Dust Cup
Release
Latch
Filter Release Button
Click
3. Brush loose debris from HEPA media
filter and pre-filter basket and then rinse
with warm water. Set both filters aside
and allow to air dry for 24 hours.
IMPORTANT: The HEPA media filter
and pre-filter must dry completely before
reuse.
4. Place the pre-filter basket back into the
dust cup, then place the HEPA media
filter back into the pre-filter basket.
2. Remove the HEPA media filter and pre-
filter basket from the dust cup. 5. To reassemble the dust cup to the hand
vacuum, align the tabs on the dust cup
with slots in the hand vacuum. Once
aligned, attach the dust cup to the hand
vacuum until you hear a click.
- 14 -
HEPA Media Filter
Pre-filter Basket
Dust Cup
EMPTYING DUST CUP AND CLEANING FILTER
2. Turn the nozzle over to access the brush
roll. As shown below, push the tab to
the unlock position " " and hold it.
Remove the locking lever.
Brush Roll Manual Cleaning
1. Make sure the vacuum cleaner is turned
off. Remove the wand and the hand
vacuum from the motorized nozzle and
set aside.
3. With the tab held in the unlock position,
lift the brush roll out of the nozzle
housing. Clean off debris and anything
wrapped around the brush roll. Use a
pair of scissors to remove threads, etc.
For best performance, clean edges of
round end caps of the brush roll and
nozzle housing regularly.
4. Place the brush roll back into the
housing. First re-insert the round end
cap of the brush roll into the other end
of the nozzle housing. Then replace
the hexagon end of the brush roll by
aligning the end cap as shown and
pressing it down into the nozzle housing
until a click is heard.
5. Reinstall the locking lever. First insert the
tab end of the locking lever into the slot
as shown. Then press down the locking
lever into place until a click is heard.
Make sure the tab is in the lock position.
Round
End Cap
- 15 -
CAUTION
Risk of injury. Brush may start
unexpectedly. Disconnect power nozzle
from wand before cleaning or servicing.
The brush roll may accumulate debris
such as strings, hair and fibers. This type
of debris can wrap around the brush and
diminish its ability to clean effectively.
CLEANING THE MOTORIZED NOZZLE & BLOCKAGES
NOTE: It is recommended to store
the vacuum within a temperature range
between 39.2°F (4°C) and 104°F (40°C).
2. Carefully remove any debris or blockage
from the inside of the hose. Reattach the
motorized nozzle onto the wand.
3. Once the blockage is removed, start the
vacuum to ensure air flow through the
hose.
Brush Roll Reset
If the brush roll is blocked or overloaded,
the unit will automatically stop power.
Switch the unit off and remove the
obstruction.
Hose Blockage Removal
1. To clean out the hose, press the wand
release button on the motorized nozzle,
and pull the motorized nozzle away
from the wand.
- 16 -
CAUTION
Do not use scissors or other sharp objects
to remove a blockage from the hose.
CLEANING THE MOTORIZED NOZZLE & BLOCKAGES
Wand Release Button
- 17 -
Review the table for solutions to minor performance problems. Any service needed, other
than maintenance described in this Use & Care Guide, should be performed by a qualified
service dealer.
TROUBLESHOOTING
WARNING
Disconnect electrical supply before performing maintenance to the vacuum cleaner.
Failure to do so could result in electrical shock or personal injury.
PROBLEM
POSSIBLE CAUSE SOLUTION
Vacuum will not
power on.
Battery may be depleted. Charge the battery as instructed on page 10.
Wrong charger being used. Be sure to use only the charger supplied with your
product.
Brush roll is jammed. Remove obstruction. Follow instructions on page
15.
Hand vacuum or battery is
damaged. Call 1-877-531-7321 (US) / 1-844-608-3081 (CA)
for assistance.
Battery indicator
does not illuminate
when charging the
battery.
Charging adapter is not plugged
into outlet firmly.
Be sure the charging adapter is plugged in
properly to the outlet, and the charging connector
is plugged into the charging port of the hand
vacuum.
Dust accumulated on the charging
port of the hand vacuum. Clean off any dust accumulated on the charging
port of the hand vacuum.
No power at electrical outlet. Check circuit breakers.
The battery is damaged. Call 1-877-531-7321 (US) / 1-844-608-3081 (CA)
for assistance.
The battery indicator is damaged. Call 1-877-531-7321 (US) / 1-844-608-3081 (CA)
for assistance.
Battery indicator
does not illuminate
when using the
vacuum.
Battery may be depleted. Charge the battery as instructed on page 10.
The battery indicator is damaged. Call 1-877-531-7321 (US) / 1-844-608-3081 (CA)
for assistance.
Battery indicator
flashes red and
then turns off when
using the vacuum.
This indicates an obstruction of
brush roll or missing of the filters,
which causes the motor protection
to trip.
With the unit turned off, check to remove any
obstruction in the brush roll or in the motor
section, reinstall the filters into place and then
re-start. If the unit cannot be re-started, call
1-877-531-7321 (US) / 1-844-608-3081 (CA) for
assistance.
Battery may be depleted. Charge the battery as instructed on page 10.
Brush roll in the
motorized nozzle is
not turning.
Brush roll is jammed. Remove obstruction. Follow instructions on page
15.
Brush roll is not installed properly. Remove the brush roll and reinstall as instructed
on page 15.
- 18 -
TROUBLESHOOTING
Brush roll in the
motorized nozzle is
not turning.
Debris accumulates on metal
contacts connecting the dust cup
and the main body of the hand
vacuum.
Remove the debris and reinstall as instructed on
page 14.
The dust cup is installed incorrectly. Reinstall the dust cup correctly as instructed on
page 14.
The hand vacuum and the wand
are not connected into place. Reinstall the hand vacuum and the wand correctly
as instructed on page 9.
The motorized nozzle and the
wand are not connected into place. Reinstall the motorized nozzle and the wand
correctly as instructed on page 15.
Nozzle motor and brush roll both
are not turning.
Check to confirm the above connections are
properly made. Re-start the unit. If the nozzle
motor and brush roll are still not turning, the
nozzle motor may be damaged. Call 1-877-531-
7321 (US) / 1-844-608-3081 (CA) for assistance.
Nozzle motor is spinning, but the
brush roll is not rotating. The belt is broken. Call 1-877-531-7321 (US) /
1-844-608-3081 (CA) for assistance.
Vacuum is not
picking up or
suction power is
weak.
Dust cup is full. Empty the dust cup.
Filter needs cleaning. Follow filter cleaning instructions on page 13-14.
Filter needs to be replaced. To purchase parts call 1-877-531-7321 (US) /
1-844-608-3081 (CA).
Battery may be depleted. Charge the battery as instructed on page 10.
Dust cup is not installed well. Check the dust cup for correct installation and
ensure it is snapped firmly in place.
Dust escapes from
vacuum.
Filter is missing or installed
incorrectly. Check the filter for correct installation. See page
13-14.
Filter is damaged and needs to be
replaced. To purchase a replacement filter, call
1-877-531-7321 (US) / 1-844-608-3081 (CA).
Dust cup is full or is installed
incorrectly. Empty the dust cup container or position the dust
cup correctly and snap firmly into place.
Pre-filter is missing or is installed
incorrectly. Reinstall correctly as instructed on page 13-14.
Vacuum turns off
on its own.
Battery may be depleted. Charge the battery as instructed on page 10.
Brush roll in the motorized nozzle
is jammed or is not installed well
causing motor protection system
activated.
With the unit turned off, remove the obstruction
or re-install the brush roll as instructed on page 15
and then re-start.
Excessive loading on brush roll
brush. Remove the obstruction and then re-start.
The suction inlet or hose is blocked
or sealed. Remove the obstruction and then re-start.
The battery is damaged. Call 1-877-531-7321 (US) / 1-844-608-3081 (CA)
for assistance.
- 1 -
Antes de usar su nueva aspiradora ................................................................................... 1
Lista de empaque .............................................................................................................1
Instrucciones de seguridad importantes ........................................................................2-4
Garantía de la aspiradora ............................................................................................... 5
Piezas y características ................................................................................................. 6-8
Instrucciones de montaje ............................................................................................ 9-10
Instrucciones de uso ...................................................................................................11-13
Mantenimiento y cuidado de la aspiradora ................................................................ 14-17
Resolución de problemas ........................................................................................... 18-19
Información de asistencia o servicio ...................................................... Posterior Cubierta
TABLA DE CONTENIDOS
LISTA DE EMPAQUE
Su ASPIRADORA INALÁMBRICA KENMORE ELITE incluye las siguientes piezas y
componentes por separado en la caja:
1 Aspiradora de mano
1 Boquilla motorizada
1 Vara
1 Herramienta combinada
Lea esta guía de uso y cuidado. Lo ayudará a ensamblar y operar su nueva aspiradora
Kenmore de la manera más segura y efectiva posible.
Para obtener más información sobre el cuidado y uso de la aspiradora, llame a la línea de
ayuda al 1-877-531-7321 (US) / 1-844-608-3081 (CA). Necesitará el modelo completo y los
números de serie al solicitar información.
El modelo de su aspiradora y los números de serie se ubican en la placa de modelo y
número de serie. Use el siguiente espacio para registrar el número de modelo y el número de
serie de su nueva aspiradora Kenmore.
N° de modelo____________________________________________
N° de serie ____________________________________________
Fecha de compra ______________________________________
Guarde este libro y su boleta (recibo) de venta en un lugar seguro para usarlos como
referencia a futuro.
ANTES DE USAR SU NUEVA ASPIRADORA
1 Soporte de montaje para pared
2 Tornillos
1 Cargador
1 Manual
- 2 -
¡ADVERTENCIA!
LEA TODAS LAS INSTRUCCIONES DE ESTA GUÍA ANTES DE ENSAMBLAR O USAR SU
ASPIRADORA. Para reducir el riesgo de incendio, descarga eléctrica, lesiones a personas
o daños al usar su aspiradora, siga todas las precauciones de seguridad indicadas a
continuación.
INSTRUCCIONES DE SEGURIDAD IMPORTANTES
Use su aspiradora solo como se indica en
esta Guía de uso y cuidado.
No use ni cargue en exteriores o sobre
superficies mojadas.
No permita que se utilice como un
juguete. Se debe prestar estricta atención
cuando es usado por niños o cuando se
use cerca de ellos, de mascotas o de
plantas.
Utilice solo los aditamentos
recomendados por el fabricante. No use
accesorios que no sean los incluidos con
esta aspiradora.
No manipule el cargador, incluido el
enchufe, ni las terminales de carga con
las manos mojadas.
No ponga objetos sobre las aberturas. No
utilizar si las aberturas están bloqueadas;
mantenga las aberturas libres de polvo,
cabellos, pelusas y cualquier cosa que
pueda reducir el flujo de aire.
Mantenga su cabello, ropas holgadas,
dedos y partes de su cuerpo lejos de las
aberturas y piezas móviles del producto.
Tenga precaución adicional al limpiar en
escaleras.
No use el producto para aspirar líquidos
combustibles o inflamables, como
gasolina, ni lo use en áreas donde tales
elementos puedan estar presentes.
Apague el electrodoméstico antes de
conectarle accesorios.
No aspire elementos que estén en llamas
o humeando, tales como cigarrillos,
fósforos o cenizas calientes.
No aspire soluciones tóxicas, como
blanqueador con cloro, amoniaco o
limpiador de drenaje.
No usar sin el contenedor de polvo y el
filtro HEPA instalados.
No cargue la unidad en exteriores.
Evite los arranques accidentales.
Asegúrese de que el producto no
funcione antes de conectarlo a la
aspiradora de mano, recoger o llevar el
aparato.
No intente cargar el aparato con el
interruptor en la posición de encendido.
No intente usar este adaptador de carga
con otro producto ni intente cargar este
producto con otro adaptador de carga.
Para recargar la aspiradora, use
solo el adaptador de carga Yinli
YLS0241A-T256080 o Xdroid XZ2560-
0800EU.
No use un electrodoméstico dañado
o modificado. Los electrodomésticos
dañados o modificados pueden presentar
un comportamiento impredecible,
provocando incendios, explosiones o
riesgo de lesiones.
No sumerja la aspiradora ni el adaptador
de carga en agua u otros líquidos.
Apague siempre la aspiradora antes
de conectar o desconectar la boquilla
motorizada.
Almacene la aspiradora inalámbrica en
interiores. Almacene la aspiradora lejos
de alcance para evitar accidentes.
Mantenga su zona de trabajo bien
iluminada.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60

Kenmore Elite CSV Mode d'emploi

Catégorie
Aspirateurs
Taper
Mode d'emploi

dans d''autres langues