Williams Sound IR Plus Flex Manuel utilisateur

IR +

Infrared and Wi-Fi Assistive Listening System

USER MANUAL

MAN 273A

2

IR Plus Assistive Listening System

Table of Contents

Safety Warnings and Instructions ��4

Avertissements et instructions de sécurité �� 4

Recycling Instructions ��6

System Overview �� 6

Wi-Fi Network Required ��6

Router and Network Equipment Selection ��6

Quick Setup Guide �� 7

Modulator Front and Back Panel �� 7

Front Panel �� 7

Back Panel ��8

Additional Devices ��9

Device Types ��9

Wiring and Cabling ��9

IR E4 ��9

Installation Instructions ��10

Determine Coverage Area ��10

Determine Location �� 11

Network Cable Connection ��11

Cable Connection to Emitters ��11

Audio Source Connections ��12

Multi-Channel Sources �� 12

Avoiding Hum in the Audio (as a Result of a Ground Loop) ��12

System Settings �� 13

Audio Settings �� 13

Server Description �� 14

Audio Channel Name ��14

IR Baseband Output �� 14

Network Conﬁguration �� 14

Restore Defaults �� 15

3

IR Plus Assistive Listening System

Web Control Interface �� 15

Login Page �� 15

Status Page ��16

Settings Page �� 17

Audio Page �� 18

Upload Image ��19

Network Page �� 20

Administration Page ��21

Front Panel Interface �� 22

Main Menu �� 22

Restoring Defaults �� 23

Audio Channel Menu �� 23

Port Menu �� 23

Device Detail Page �� 23

Locking the Front Panel �� 23

WaveCAST App �� 24

Connect to Wi-Fi Network �� 24

Connecting the App to the Channel �� 24

Listening via the App �� 24

Note on Wi-Fi Assist/Smart Network Switching �� 24

Troubleshooting �� 24

Speciﬁcations �� 28

Mounting Options �� 29

Optional Receivers �� 29

Regulatory Statements �� 29

FCC �� 29

ISED �� 29

VCCI ��29

IR M1: 2-Year Warranty Statement �� 30

IR E4: 2-Year Warranty Statement �� 31

4

IR Plus Assistive Listening System

Safety Warnings and Instruc-

tions

WARNING! TO REDUCE THE RISK OF FIRE OR

ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN

OR MOISTURE.

CAUTION! TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER. NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

POWER CORD NOTICE FOR INTERNATIONAL

OPERATION - Please call Williams AV Customer Service

at 800.328.6190 to order the appropriate power cord for

the country of use.

Important Safety Instructions:

1. Read and follow these instructions

2. Keep these instructions

3. Clean only with dry cloth.

4. Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

5. Do not install near any heat sources such

as radiators, heat registers, stoves, or other

appliance (including ampliﬁers) that produce heat.

6. Do not defeat the safety purpose of the polarized

or grounding-type plug. A polarized plug has two

blades with one wider than the other. A grounding

type plug has two blades and a third grounding

prong. The wide blade or the third prong is

provided for your safety. If the provided plug does

not ﬁt into your outlet, consult an electrician for

replacement of the obsolete outlet.

7. Protect the power cord from being walked on

or pinched particularly at plugs, convenience

receptacles, and the point where they exit from

the appliance.

8. Only use attachments/accessories speciﬁed by

the manufacturer.

9. Unplug this appliance during lightning storms or

when unused for long periods of time.

10. Power Sources - The appliance should be

connected to a power supply only of the type

described in the operating instructions or as

marked on the appliance.

11. Object and Liquid Entry - Care should be taken so

that objects do not fall and liquids are not spilled

into the enclosure through the openings. Do not

use this appliance near water or expose it to

liquids.

12. Servicing - The user should not attempt to service

the appliance beyond that described in the operating

instructions. All other servicing should be referred to

qualiﬁed service personnel.

Precautions:

1. Power – WARNING, BEFORE TURNING ON THE POWER

FOR THE FIRST TIME, READ THE FOLLOWING SECTION

CAREFULLY. The unit is designed for use only with the

line cord of the region in which it will be operated.

2. Voltage Label (Rear Panel) – A label located at the rear

panel power connection indicates the DC power input for

the unit. The label will read 48VDC.

3. Do Not Plug in the input, output, Ethernet, or Dante

connections while the power switch is switched to the

ON position.

4. Do Not Touch the IR M1 with wet hands. Do not handle the

IR M1 or power cord when your hands are wet or damp. If

water or any other liquid enters the IR M1 cabinet, take the

IR M1 to qualiﬁed service personnel for inspection.

5. Place the IR M1 in a well ventilated location. Take special

care to provide plenty of ventilation on all sides of the

IR M1 especially when it is placed in an audio rack. If

ventilation is blocked, the IR M1 may over heat and

malfunction. Do not expose the IR M1 to direct sun

light or heating units as the IR M1 internal components

temperature may rise and shorten the life of the

components. Avoid damp and dusty places.

6. Care – From time to time you should wipe o the front

and side panels and the cabinet with a soft cloth. Do not

use rough material, thinners, alcohol or other chemical

solvents or cloths since this may damage the ﬁnish or

remove the panel graphics.

Avertissements et instructions de

sécurité

AVERTISSEMENT! POUR RÉDUIRE LES RISQUES

D’INCENDIE OU DE CHOC ÉLECTRIQUE, NE PAS EXPOSER

CET APPAREIL À LA PLUIE OU À L’HUMIDITÉ.

MISE EN GARDE! POUR RÉDUIRE LE RISQUE DE

CHOC ÉLECTRIQUE, NE PAS RETIRER LE COUVERCLE.

L’APPAREIL NE CONTIENT AUCUNE PIÈCE RÉPARABLE

PAR L’UTILISATEUR. CONFIER LES RÉPARATIONS À UN

RÉPARATEUR QUALIFIÉ.

AVIS CONCERNANT LE CORDON D’ALIMENTATION

POUR UNE UTILISATION HORS DES ÉTATS-UNIS –

Prière d’appeler le service à la clientèle de Williams AV au

800.328.6190 pour commander le cordon d’alimentation

adapté au pays dans lequel l’appareil va être utilisé.

Consignes de sécurité importantes:

1. Lire ces instructions

2. Conserver ces instructions

3. Nettoyer avec un chion sec uniquement.

5

IR Plus Assistive Listening System

4. Ne pas bloquer les évents de ventilation.

Installer conformément aux instructions du

fabricant.

5. Ne pas installer à proximité de sources

de chaleur telles que radiateurs, registres

de chaleur, cuisinières ou autres appareils (y

compris les ampliﬁcateurs) qui produisent de

la chaleur.

6. Ne pas supprimer ou contourner la fonction

de sécurité de la ﬁche polarisée ou de mise

à la terre. Une ﬁche polarisée a deux broches

dont l’une est plus large que l’autre. Une ﬁche

de mise à la terre a deux broches et une

troisième broche de mise à la terre. La lame

large ou la troisième broche est fournie à des

ﬁns de sécurité. Si la ﬁche fournie ne rentre

pas dans la prise, consulter un électricien pour

le remplacement de la prise obsolète.

7. Protéger le cordon d’alimentation contre tout

piétinement ou pincement, en particulier au

niveau des ﬁches, des prises de courant et de

l’endroit où il sort de l’appareil.

8. Utiliser uniquement les pièces/accessoires

spéciﬁés par le fabricant.

9. Débrancher cet appareil pendant les

orages ou lorsqu’il n’est pas utilisé pendant de

longues périodes.

10. Sources d’alimentation - L’appareil doit

être connecté à une alimentation électrique

uniquement du type décrit dans le mode

d’emploi ou tel qu’indiqué sur l’appareil.

11. Pénétration d’objets et de liquides - Des

précautions doivent être prises pour que des

objets ne tombent pas et que des liquides ne

soient pas renversés dans le boîtier par les

ouvertures.

11. Réparation et entretien - L’utilisateur ne doit

pas tenter de réparer l’appareil autrement que

de la manière décrite dans le mode d’emploi.

Toute autre tâche d’entretien ou de réparation

doit être conﬁée à un technicien qualiﬁé.

Précautions:

1. Alimentation – AVERTISSEMENT: AVANT

DE METTRE L’APPAREIL EN MARCHE POUR LA

PREMIÈRE FOIS, LIRE SOIGNEUSEMENT LA

SECTION QUI SUIT. L’ampliﬁcateur est conçu

pour être utilisé uniquement avec un cordon

d’alimentation adaptéà la région dans laquelle

il sera utilisé.

2. Étiquette de tension (panneau arrière) - Une

étiquette située au niveau du raccordement

électrique sur le panneau arrière indique

la puissance consommée CA de appareil.

L’étiquette indiquera 48VDC.

3. Ne pas brancher les connexions

d’entrée, de sortie, Ethernet ou USB lorsque l’interrupteur

d’alimentation est sur la position de marche.

4. Ne pas toucher le IR M1 avec les mains mouillées. Ne

pas manipuler le IR M1 ou le cordon d’alimentation avec

les mains mouillées ou humides. Si de l’eau ou tout autre

liquide pénètre dans l’armoire du IR M1, conﬁer l’appareil à

un technicien qualiﬁé pour inspection.

5. Placer le IR M1 dans un endroit bien ventilé. Veiller tout

particulièrement à assurer une ventilation susante de

tous les côtés du IR M1, en particulier lorsqu’il est placé

dans un rack audio. Si la ventilation est bloquée, le IR M1

peut surchauer et dysfonctionner. Ne pas exposer le IR

M1 à la lumière directe du soleil ou à des appareils de

chauage, car la température des composants internes du

IR M1 pourrait augmenter et réduire la durée de vie des

composants. Éviter les endroits humides et poussiéreux.

6. Entretien - De temps en temps, essuyer les panneaux

avant et latéraux et le boîtier avec un chion doux. Ne

pas utiliser un matériel abrasif, des diluants, de l’alcool

ou d’autres solvants ou chions contenant des produits

chimiques, au risque d’endommager la ﬁnition ou d’eacer

les indications fournies sur le panneau.

6

IR Plus Assistive Listening System

Recycling Instructions

Help Williams AV protect the environment! Please take the time to dispose of your equipment properly.

Product Recycling:

Please do NOT dispose of your equipment or batteries in the household trash. Please take the equipment to an

electronics recycling center for proper disposal.

System Overview

The IR + System uses invisible infrared (IR) light to broadcast speech or music to wireless infrared receivers. Listeners can

also use their own personal electronic devices with Wi-Fi.

The new IR + is designed to support those who want to use their own smartphones and headphones for a more discreet

assistive listening experience. Simplicity is also available for those who want a more traditional assistive listening system with

a dedicated IR receiver and headset. Venues no longer need to choose between providing IR or Wi-Fi assistive listening

systems. IR + supports the iOS and Android WaveCAST Apps and the Wi-Fi Receiver-- in addition to all of the current and

legacy Williams Sound IR receivers.

The system is designed to transmit high quality audio for hearing assistance and language translation applications. Because

the system uses infrared light for transmission, it is not aected by interference from radio equipment and does not interfere

with radio equipment. No FCC license or radio approval is required.

The system can be used with microphones as a stand-alone system, or can be connected to other sound equipment. Infrared

systems generally cannot be used in direct sunlight because of sunlight’s large amount of interfering infrared light.

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15

of the FCC Rules� These limits are designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment� This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio

communications� Operation of this equipment in a residential area is likely to cause harmful interference in which case

the user will be required to correct the interference at his own expense�

NOTICE: A plasma monitor can degrade the audio quality of the IR Plus.

Wi-Fi Network Required

The IR M1 connects to the installation location's Wi-Fi Network. It does not provide a network on its own. The Wi-Fi network

will need to be installed and established before the Wi-Fi features of the IR M1 can be used.

Router and Network Equipment Selection

The IR M1 does not come with its own router or networking equipment. It is intended to be set up on an already existing Wi-Fi

network; however, upgrades to your network equipment may be necessary depending on the performance desired from the

IR M1. For instance, a higher-end router may allow more users to connect to your audio stream than using a less robust router.

The Wi-Fi network will need to be accessible to the users who will be listening to the audio. A public or Guest Wi-Fi network

will usually be ideal for ease of accessibility. If the user's devices cannot connect to the network due to security settings, they

will not be able to hear the audio.

Multicast connections are required to use the Wi-Fi features of the IR + system. Not all routers support multicast. Check with

your router's manufacturer to ensure the router you are using supports multicast connections.

The IR + system will put a demand on the network. If the network cannot handle the demand, whether because it is being

used for other networking needs or because the networking hardware is not strong enough, the IR M1 will be unable to reach

it's maximum audience.

When streaming to a small or medium sized audience, a basic networking conﬁguration may suce. When streaming music

using multiple channels (such as having several IR M1 units on your network), a powerful router and network conﬁguration is

more likely to be required.

7

IR Plus Assistive Listening System

The WaveCAST Networking Guide is available on the Williams AV website for additional networking tips, and applies to

all Williams AV Wi-Fi assistive listening products.

Multiple Units

Up to 4 WaveCAST systems (including WaveCAST, IR M1, FM+ and more) can be used on the same Wi-Fi network.

Multiple devices will work better on more powerful networks and routers.

The number of servers on the network is visible on the front panel of the IR M1. The number assigned to a speciﬁc server

is also visible.

Quick Setup Guide

1. Place your IR M1 in a location where you will be able to place IR emitters in the listening area.

2. Plug in the power supply to the power connection.

3. Connect an audio source to the Line/Mic In port for the channel(s) you'd like to use.

4. Connect an Ethernet cable to the ETHERNET port. Connect the other end of the Ethernet cable to a multicast-enabled

router with an internet connection..

5. Connect one or more IR E4 emitter to Output to Emitter ports on the back of the IR M1 with an CAT5e cable.

6. Place the emitters in the listening area so that they are above the audience without interference. Multiple emitters

should be place apart from one another to expand the coverage area.

7. Turn on the IR M1.

8. On the front panel of the IR M1, an IP address should be displayed. If you do not see an IP address, check your

network connection. Write it down and go to a computer on the same network as the IR +.

9. In Chrome or Edge, type the IP address into the URL bar. A webpage for the IR + system will load. The default

usename is admin and the default password is admin.

10. Click the Audio tab and set the audio device type and desired settings for each audio channel.

11. Click the Settings tab. Conﬁgure each emitter for the channels it will broadcast, and the IR Band the system should

emit.

12. Change other settings as desired.

13. With your audio source playing sound, take an IR Receiver to the front panel of the IR M1. The front panel of the IR M1

has two small IR Emitters for testing, one for each audio channel. Tune the receiver to the IR Baseband channel the

audio is playing on to ensure all your settings sound correct. This audio will match the audio from the IR E4 emitters.

IR M1 Front and Back Panel

The IR M1 works as a control center for the IR Plus system. Additional devices, such as emitters, are controlled through

the IR M1.

Front Panel

Diagram

Power Button

The IR M1 has a switch that turns the modulator on or o. The desktop power supply provides power to the unit at all

times.

OLED Display

This shows current status of channels and of the IR M1. Each time the power of the unit is turned on, the OLED Display

shows a Williams AV start-up screen followed by the ﬁrmware blob version number. After several seconds, the default

Main Info Screen screen will be displayed.

8

IR Plus Assistive Listening System

Screen Time Out

If no buttons are pressed on the IR M1 for a while, the display will shut o. Pressing any button on the front panel will re-activate

the screen.

Navigating the Front Panel

The arrow buttons (up, down, left and right) on the front panel of the IR M1 are used to navigate the front panel menu. See "Front

Panel Interface" on page 22 for how to use the arrows on each screen.

Headphone Jacks

Two headphone jacks are available on the front panel to listen to the raw audio input, one for channel A and one for channel B.

The audio sent to the headphone jacks is before the IR + system makes any adjustments to the audio, so the listener will not hear

any gain, compression or other adjustments.

Built in Emitters

Two emitters are built into the IR M1 for testing purposes. These emitters are not strong enough for sending audio to an audience,

but are suitable for testing the device when setting it up. There is an emitter for audio output channel A and a separate emitter for

channel B. Use any applicable Williams Sound receiver to test the audio. Hold the receiver within a few feet of the IR M1; the built-

in emitter coverage area is not large and is only for testing.

The built-in emitters will not work without an IR E4 emitter connected to the IR M1 with the desired audio channel enabled. For

example, if there is an active audio source on CH A and an emitter with Audio Channel A enabled, the built-in IR emitter on the

front panel will broadcast Audio Channel A on the appropriate IR Baseband Channel (see "IR Baseband Output" on page 14).

If either Audio Channel is not actively enabled on at least one IR device attached to the M1, the front panel's built-in emitter will not

transmit anything, even if an audio source is present.

Back Panel

Diagram

ETHERNET

STREAMING

AUDIO OUT

Output to Emitters

1 2 3 4

Audio Input

Two audio devices can be connected via the Line/Mic In ports. Each port is for one audio output channel. The source will need to

be set via the web interface or front panel for the IR M1 to conﬁgure the gain level for the audio source correctly.

Dante™ (Optional)

An input for Dante audio is available on some devices.

Ethernet

The Ethernet connect is for connecting to a network and/or providing an internet connection. No emitters or other devices should

be connected to the Ethernet port.

Output to Emitters

Emitters and expansion arrays are connected to the Output to Emitter ports. There are four ports on the IR M1. These speciﬁc ports

will often be referred to as Ports throughout the website and this manual.

Although a standard Ethernet cable is used for these connections, no network information is provided through these ports. Only

approved Williams Sound devices may be connected to the Output to Emitter ports on the back of the IR M1. Use the designated

Ethernet port on the back of the IR M1 for network and internet connections.

Power

Connect the provided power supply to the power port.

9

IR Plus Assistive Listening System

Additional Devices

To create a full IR system, additional devices will need to be connected to the IR M1. Note that devices can be disconnected or

connected to the IR M1 at any time without needing to shut o or power cycle the IR M1.

The IR E4 is an IR Emitter and up to four can be directly connected to the IR M1.

Device Types

Several types of devices may be plugged into the IR M1 modulator. Not all of these device types are valid and can indicate a

problem with the IR + setup or device.

DEVICE TYPE SHORT DESCRIPTION MEANING

IR E4 Emitter IR E4 Valid Device. An IR Emitter.

Unknown UNKWN This type of device is not recognized. There may be a short in

the device that is preventing the system from detecting what it is.

Invalid INVLD This device is not connected in a usable manner. The IR + system

may not have a required ﬁrmware update to recognize this

device type.

None --- Nothing is detected as being plugged into the port.

The device type can be viewed on the IR M1 website, or via the front panel and may be useful when troubleshooting.

Wiring and Cabling

CAT5e cables must be used for connecting devices. They are not required to be shielded. The maximum recommended cable

length is 300 ft (91.4 m).

Each CAT5e cable connection from the IR M1 system to the IR E4 emitters carries the following signals:

• Baseband signals for 1 or 2 IR channels

• +48V power supply for the IR E4

• RS-485 bus communications

IR E4

Back Panel of IR E4

The IR E4 is connected to the IR M1 via a CAT5e cable. Once connected, any changes required can be made through the IR M1's

webpage.

The IR E4 receives its power from the Ethernet cable and no additional power supply is required.

Note: Although the IR E4 receives power from an Ethernet cable, it does not follow the formal Power over Ethernet (PoE) standard�

10

IR Plus Assistive Listening System

0°

10°

0ft/0m

25ft/8m

50ft/15m

75ft/23m

IR + Coverage Pattern

0ft/0m

25ft/8m

50ft/15m

75ft/23m

100ft/30m

125ft/38m

150ft/46m

175ft/53m

200ft/61m

225ft/69m

20°

30°

40°

50°

60°

70°

80°

90°

RX22-4 Receiver RX20 Receiver

Installation Instructions

The IR M1 Modulator is the key component to the IR+ System. Audio devices, emitters and more can be connected to the IR M1.

This section will cover the installation instructions for physically setting up your IR + system.

Determine Coverage Area

When using the IR + system in single-channel mode with the RX22-4 receiver, the system coverage area will cover up to 18,000

sq. ft. (1,673 sq. m.) per IR E4 emitter. When in two-channel mode, the maximum IR coverage area will drop to accommodate for

broadcasting two dierent audio signals instead of one. Decreasing the emitter power level will also decrease the coverage area.

The IR E4 will use full power, single channel mode by default. Single channel or dual channel mode, and emitter output power, can

be selected using the system webpage.

Connect the number of E4's needed to cover the space required.

Interference

Most objects block infrared light. The coverage area may be aected by direct/indirect sunlight, reﬂections on walls and room

construction. The emitter cannot be concealed behind walls, glass, curtains, etc. Reﬂections of the infrared light from walls,

ceilings, and ﬂoors may change these patterns.

These patterns are the direct radiation pattern. The infrared radiation does not drop to zero outside the illustrated patterns; it

decreases. It still may be usable at a greater distance, depending on the receiver sensitivity and the reﬂective characteristics of

the room.

Important: point the emitter towards the listening audience from high up� Bodies can block the infrared signal from reaching various

parts of the audience if at a poorly selected angle�

Do not paint the front face of the IR E4.

11

IR Plus Assistive Listening System

Determine Location

The modulator is usually located with the sound system ampliﬁer or mixer for easy access to an audio input signal. For portable

systems, the modulator can be placed near the emitter or in another convenient location.

Position the IR E4 emitters so the area is well covered and has minimal interference. The emitters should be placed high on

the wall, aimed into the coverage area and angled down toward the audience. For help determining ideal IR coverage area or

avoiding obstacles, contact Tech Blue Design and Support Services (see "Troubleshooting" on page 24).

Network Cable Connection

The Ethernet port can be used to connect the IR M1 to a local network. A network connection is required to access the IR M1

webpage. The webpage is needed to conﬁgure some device settings after the system is set up.

An Ethernet connection alone will not allow the Wi-Fi broadcast features to work; a Wi-Fi connection must be available on the

network. A network connection is not required for broadcasting over infrared.

Once a connection has been established, an IP address will automatically be assigned to the IR M1 (see the front panel section's

"Front Panel Interface" on page 22 for help ﬁnding the IP Address). Device settings can then be set via the web interface,

including changing any network settings.

Cable Connection to Emitters

The IR M1 can directly drive four emitters. The modulator outputs CANNOT be split with CAT5e splitters.

Determine the length of RJ-45 cable needed to reach from the Emitter to the Modulator unit. For more information on cabling, see

"Wiring and Cabling" on page 9.

INPUT INPUT

EMITTER (IR E4)EMITTER (IR E4)

OUTPUT OUTPUT

48VDC

ETHERNET

STREAMING

AUDIO OUT

Output to Emitters

1 2 3 4

IR M1 MODULATOR (REAR)

12

IR Plus Assistive Listening System

Audio Source Connections

The IR M1 Modulator will accept the following audio sources:

1. Balanced Microphone with or without 12-volt phantom power (DIN 45596) on a 3-pin (XLR) connector.

2. Balanced/Unbalanced microphone with or without phantom power on 1/4 inch (TRS) jack

3. Balanced/Unbalanced Line on a 3-pin (XLR) connector.

4. Balanced/Unbalanced Line on 1/4 inch (TRS) jack.

5. Dante on an RJ-45 jack (optional).

WARNING:

The IR + is not designed to accept 70 volt speaker signals! This may result in damage to your system. The sound

source should come directly from the system mixer or digital source as a low-level or unprocessed signal.

BALANCED LINE USING 3–PIN CONNECTOR

IN PHASE

1 2

3

3 PIN CONNECTOR

A108

UNBALANCED LINE USING 3–PIN CONNECTOR

1 2

3

3 PIN CONNECTOR

A105

BALANCED LINE USING 1/4" CONNECTOR

IN PHASE

A106

UNBALANCED LINE USING 1/4" CONNECTOR

A107

4.7 K

SOURCE A

SOURCE B

CONNECTING TO A MULTI-CHANNEL OR STEREO SOURCE

A109

Multi-Channel Sources

By constructing a simple resistive mixer, stereo (or 3 channel) sources can be connected to the IR +. Additional channels can be

accommodated by adding a resistor for each source.

Note: The Dante audio input will automatically mix the left and right channels�

Avoiding Hum in the Audio (as a Result of a Ground Loop)

A hum created by a ground loop can often be eliminated by connecting a capacitor in series with the audio line shield to the

modulator’s ground. This method also maintains good radio frequency (RF) shielding. Determining the eectiveness of this method

for your installation usually requires some experimentation.

IN PHASE

1 2

3

3-PIN

CONNECTOR

BREAKING A GROUND LOOP WHEN

CONNECTING TO A UNBALANCED LINE

BREAKING A GROUND LOOP WHEN

CONNECTING TO A BALANCED LINE

.01 uF CERAMIC DISC

CAPACITOR .01 uF CERAMIC

DISC CAPACITOR

A110

13

IR Plus Assistive Listening System

System Settings

Most settings are adjusted via the web interface by using a computer (see "Web Control Interface" on page 15). A handful of

settings can be adjusted via the front panel display (see "Front Panel Interface" on page 22).

Any conﬁguration to the IR+ system is done through the IR M1, which passes the conﬁguration setting onto other IR+ devices.

Audio Settings

The Audio Settings provide the ability to change the audio characteristics for dierent listening applications.

Audio Input Source

The Audio Input Source menu has ﬁve possible selections to choose from: Line In, Mic In, 400Hz Test Tone, Mic + Phantom Power,

or Dante.

Selecting an Audio Source Appropriate for Hearing Impaired Listeners

The IR + transmits audio with excellent ﬁdelity. Therefore, the audio source signal should be of the highest audio quality and not

subject to a compressor, limiter, reverberation, or other signal processing equipment. While compressed audio is available through

the IR +, excessive compression is not helpful to the hearing impaired and can contribute to excessive noise in the audio.

The IR + audio source signal is usually connected to a mixer’s line output signal which is behind the mixer’s parametric equalizers

but ahead of any equalization used for house loudspeakers.

If audio delay is available for use in large auditoriums, it’s usually best to use it. Because radio signals travel faster than sound,

delaying the transmitted audio so that an average listener (in the middle of the listening area) hears the transmitted audio a few

milliseconds after audio from the main sound reinforcement system speaker is helpful. This will also help audience members who

lip read.

Audio Input Gain

The Audio Input Gain adjusts the audio output level from the IR M1. Changes to the input level will aect the level indicated by the

front panel display when audio is present. The gain can be adjusted from -60dB to +24dB.

Audio Presets

The Audio Presets allow the user to quickly and easily conﬁgure the IR M1 for common applications. The audio preset can only be

adjusted via the Web Interface.

There are three pre-conﬁgured to choose from: Hearing Assist, Music, and Voice. When one of these selections is made, the

performance of the IR M1 is immediately optimized for the needs of that application (an adjustment is automatically made to the

Low-pass Filter, High-pass Filter, and Compression).

By default, the IR M1 is shipped in the Music mode.

For music, concerts, and other applications where the highest audio quality is desirable, Music is the recommended mode of

operation.

For hearing assistance applications, or applications where the message is critical for listening, Hearing Assist is the

recommended mode of operation.

For speaking and other voice applications, Voice is the preferred mode of operation.

A Custom preset is also available for conﬁguring channel-speciﬁc audio settings.

Audio Input Level Indicator

The bar graph indicator shows audio level in 3dB steps at the output of the audio level processing circuit. The indicator is peak

responding and is calibrated so that optimum level is reached when the VU meter only fully lit (+9dB) occasionally and typically

hovers around 2/3rds lit (0dB). Adjust the audio levels from the front panel (see "Audio Channel Menu" on page 23)or from the

web interface (see "Audio Page" on page 18).

Input Overload Indication

The OLED Display shows an exclamation mark (!) above each channel's VU meter as an overload warning each time the audio

signal exceeds the capacity of the input circuit. Either the source of the audio coming in to the IR M1 needs to be adjusted to

correct this or the Audio Input Gain needs to be adjusted. A warning will also appear on the web interface if overloaded.

14

IR Plus Assistive Listening System

Server Description

The Server Description ﬁeld allows the user to easily identify the IR M1. This typically comes into play when multiple IR M1s need to

be distinguished from one another. The description appears on the front main info screen, and also on the web page. In a rack, all

the user has to do is activate the main info screen with a touch of any button on the front, and the description is displayed as one

of the ﬁelds on the main info screen.

The description can only be edited from the web interface.

Audio Channel Name

The Audio Channel Name allows the listeners to easily identify the channel. The description appears on the on the web page, and

in the WaveCAST App. The channel description can only be edited from the web interface.

IR Baseband Output

The IR baseband frequencies will broadcast audio output channels A and B. The frequencies can either be 2.3 MHz for Channel

A and 2.8 MHz for channel B, or be 3.3 MHz for Channel A and 3.8 MHz for Channel B. Which frequencies the IR + system is

broadcasting over is adjustable via the web interface.

On a Williams Sound IR Receiver, the numeric channel numbers on the receiver represent a speciﬁc IR frequency. The receiver

should be set to use the channel with the frequency that the audio output channel is being sent over.

IR OUTPUT

CHANNEL FREQUENCY

MHZ AUDIO OUTPUT

CHANNEL

1 2.3 A

2 2.8 B

3 3.3 A

4 3.8 B

Audio will not be output to IR emitters if:

• an audio output channel is muted (silent for too long). This timeout can be adjusted via the web interface.

• no IR Emitter is connected to any port, or any connected emitters are disabled.

• there is no emitter conﬁgured to use that channel

Audio will be output over Wi-Fi as long as Wi-Fi audio is enabled for that channel.

LEDs

The LED lights on the Ethernet and Output to Emitter ports can be used to help troubleshoot issues, but may be distracting if

left on during normal usage. These LEDs may be disabled on the via the Web Interface for attached devices, but they cannot be

disabled on the IR M1.

• Green – Communication Active: Flashes as long as there are communications ongoing over that port, otherwise remaining

dark.

• Amber – Channel Signals Present: On the IR M1, the amber light ﬂashes when audio is sent to an attached device. On

attached devices, the amber light ﬂashes when audio is received by the attached device. The ﬂashing will speed up when

both channels are in use. The pacing of the light does not indicate the audio rate, like a VU meter; it merely that data

transfer is occurring. Otherwise, if audio is not being sent or received, the LEDs remains dark.

Network Conﬁguration

Network Settings can only be edited from the web interface. An IP address will be automatically assigned to the IR M1 once an

Ethernet cable has been connected between the IR M1 and the router and a network connection has been found. Additional

conﬁguration would need to be made through the web interface.

Adjusting Network Settings

The Network Settings screen where the IP Address Mode (Static or DHCP), the IP Address, and Subnet Mask are set via the web

interface. See "Network Page" on page 20 for details on how to use the web interface.

IP Address Mode Static or DHCP

IP Address If the IP Address Mode is set to Static, this is where the IP Address is manually entered

Subnet Mask If the IP Address Mode is set to Static, this is where the Subnet Mask is manually entered

Gateway If the IP Address Mode is set to Static, this is where the gateway is manually entered

Multicast Address If needed, the multicast cast address can be enabled and either manually set. If not manually set, a preset ﬁxed

address will be assigned by the IR M1. This setting is under the Options menu and is set per channel.

DHCP IP Addresses are automatically created, and are usually preferred to a manual static IP address.

15

IR Plus Assistive Listening System

To set up a static IP Address:

1. Determine an appropriate static IP address for the IR M1.

a. If someone set up your network, they may be able to help you determine an appropriate IP address (i.e. network system

administrator).

b. There should be no other device having this same address on the network.

c. This will be an address on the same subnet as the router.

For example, if the router’s address is 192.168.1.100, the ﬁrst three sets of numbers will be the same (i.e. 192.168.1), and the last

number will be the number you determine for the IR M1 (i.e. .You can choose another number instead of .100).

When you determine this address, remember or write it down. You will need it for a later step.

2. Set the Static IP Address for the IR M1 via the web interface of the IR M1 (see "Network Page" on page 20).

a. Enter the IP Address you determined earlier. (When entering/saving the new address, the IR M1 will automatically change its

IP Address Mode to STATIC)

b. Network settings in the IR M1 take place immediately after saving and rebooting.

Restore Defaults

The Restore Defaults action will restore the IR M1 to it’s original factory settings. Restoring defaults from the front panel of the IR M1

will reset all settings.

On the front panel menu, it is hidden on the main screen ("Main Menu" on page 22).

Restoring defaults from the web page will reset all settings except Network connectivity settings (IP Address, Subnet Mask, IP

Address Mode, and Web Password). This maintains connectivity between the Web Page and the IR M1, after the IR M1 reboots.

In the web interface, this feature is under the Admin menu.

Web Control Interface

The IR M1 provides a web interface to manage the device settings. These web pages can be accessed over either a hardwired or

wireless network connection with the Chrome browser.

Changes take eect when applied or saved. Any updates made through the front panel will show up on the web interface once

the current page has been navigated away from, either by refreshing the page or going to a new page.

1. Open Chrome.

2. In the address bar of the browser, type in the IP address of the IR M1 and hit Enter.

3. The web page will say 'Fetching Data' as it connects to the IR M1 and gathers data of every connected machine. This may take

several seconds.

4. You should see the Login Page of the IR M1.

• If you only see a page asking for a ﬁrmware update, your device may have been corrupted. See "Website problems" on page

24

Login Page

The default User name is “admin” and the default password is “admin”. The user name and the password can (and should) be

changed on the website's Admin page.

Check with your system administrator for the most recent login credentials.

16

IR Plus Assistive Listening System

Status Page

The status screen displays the current status of any devices connected to the IR M1. It displays the port the device is connected to,

the type of device, whether audio is broadcasting over a channel, whether a channel is conﬁgured to broadcast audio, and alerts

on the temperature, power level, or other errors.

If a device is oine or disabled, this will be stated in the State column. The device is oine, it may be booting or experiencing an

error. Disabled devices are manually set to be disabled on the settings menu. Disabled or oine devices are unable to broadcast.

Online devices are fully available to broadcast. The online or oine status does not indicate any internet or network connectivity.

Rarely, a device type cannot be properly detected. See "Device Types" on page 9 for more information.

Unlike other pages on the website, this page will automatically update after a short delay with new device information when it is

available.

Errors

When an error occurs, the device will automatically switch to oine status (or remain disabled). The system will then report what it

can about the problem that occurred.

Three type of errors are available on the status screen. If a device has overheated, the Temp ﬁeld will show there is an error. If a

device is having an issue with power, the power ﬁeld may show an error. There may or may not be additional information available

for these types of errors and these errors likely cannot be automatically repaired.

Under Status, if the device has detailed error information, it will display in a red box under the device information.

The IR M1 can attempt to repair the error. When an error appears on the status screen, click the reset the error button. The

connected device may go oine brieﬂy while the system attempts to repair the error.

Not all errors can be corrected automatically; if the error persists, you should contact TechBlue Technical Support Services for help

with your device (see "Troubleshooting" on page 24). When called or e-mailed, TechBlue may ask for the error code or error

number shown in the red information box on the status screen.

Current Status

When a device is oine or disabled, the temp, power and error status cannot be guaranteed to be currently accurate. The system

is reporting the status before the device was set into oine mode to help troubleshoot what may have caused the issue. If the

device has not indicated there was an error with temp, power, and/or status, these ﬁelds will display '--'.

Once the device is repaired and online again, it can report the current status of OK.

17

IR Plus Assistive Listening System

Settings Page

The Settings page is used to adjust settings for Williams Sound devices attached to the IR M1 as well as settings for the IR M1 itself.

Modulator Information

Modulator information is adjusted on the Settings page. These are settings speciﬁc to the IR M1. The IR M1 can be named by

editing the Description ﬁeld. The IR band used for broadcasting is set here. The IR Mute timeout is how long the device waits

during silence to shut o the IR transmission and can be adjusted.

Device Settings

A list of devices will be available.

For each connected device, several settings can be adjusted. The name of the device can be set. Channel A and B can be active

or deactivated. The power level used for the IR transmission can be set to full power, or medium power (about half of the full

power level). LED lights can be enabled or disabled, meaning the lights will stay dark when operating. The connected device can

be completely disabled or enabled; a disabled device will be treated similarly to as if it was disconnected by the IR + system.

Connected, Disabled and Disconnected Devices and Settings Transfer

The settings screen will display the settings stored for the device usually connected to that port, even if it is not currently

physically connected via a CAT5e cable. These default settings are stored by the IR M1 and are saved for an individual Output to

Emitter port.

If a device is not currently connected to that port, and a dierent device of the same type is connected (for example, an IR E4

is replaced with a dierent IR E4), the stored settings will transfer automatically to that new devices. Connecting a device of a

dierent type will not transfer the settings.

Changes to the settings can only be made when a device is connected and enabled. Disabled device's settings and currently

disconnected device's settings cannot be edited. A disabled device can be re-enabled from the web interface if it is connected to

the IR M1.

Disabled devices are not being provided power by the modulator. This can be useful if it is dicult to physically unplug the device.

If a connected device is in an error state, it will be treated as if it is disabled until the error is corrected.

Devices cannot be enabled if their ﬁrmware is out-of-date. See "Administration Page" on page 21 for more information on

Firmware Updates.

18

IR Plus Assistive Listening System

Audio Page

The Audio page displays all current audio settings. Most of the settings on the audio page are per audio channel. Settings for

channel A are edited separately from channel B.

Two VU meters are visible at the top of the page. Each VU meter for informational purposes only, and does not set any settings.

Note: Network speed can aect the audio monitor updating and web page performance�

Audio Input Gain adjusts the audio volume. Up or down adjustment buttons are used to set the gain.

The audio input source selects the type of audio source that is connected to the selected channel.

Audio Presets adjust the sound to speciﬁc settings to improve the audio quality depending on if you are broadcasting audio that

is primarily voice, music, or for an audience requiring hearing assistance. The audio settings can also be manually adjusted in the

custom presets section.

See "Audio Settings" on page 13 for more details on adjusting any of these settings.

19

IR Plus Assistive Listening System

Upload Image

For each channel, an image can be uploaded that will display for any users listening using the WaveCAST app. This image can be

used to easily distinguish the content of your audio broadcast. The image must be under 128kB and be in PNG or JPG format.

The image can be replaced at any time. To completely remove the image, the device must be fully restored to factory defaults via

the front panel menu (see "Restoring Defaults" on page 23).

20

IR Plus Assistive Listening System

Network Page

The Network Settings page aects settings speciﬁc to the server as a whole. The page displays network connectivity settings,

which are typically not needed after initial installation.

Changing a static IP address or subnet will not instantly take place. The changed IP address or subnet will only take aect once

the device is rebooted,. The device will automatically reboot when saving changes to the IP Address settings.

Note: If the IP address or subnet of the device was changed and the device is being rebooted, the website may not be available at

the same URL location� Take note of the network information before rebooting the device�

TTL can be modiﬁed if there is a need. The recommended setting for the least latency is 1, but it can be set up to 31. This setting

should not be adjusted without proper consideration for your system setup.

For each channel, the security settings and the multicast information of the channel can be adjusted.

Secure Mode can be enabled or disabled, and a 6-digit PIN number can be assigned. If enabled, users will need to use this PIN to

log on to the audio stream. Users attempting to listen to the stream without the PIN will be unable to do so.

A multicast address can be automatically assigned. If a speciﬁc multicast address is required, the device administrator can enter

the desired multicast address. There is no unicast mode of the IR +.

Additional networking information is described in "Network Conﬁguration" on page 14.

La page charge ...

Williams Sound IR Plus Flex Manuel utilisateur

Williams Sound IR Plus Flex Manuel utilisateur

dans d''autres langues

Autres documents