MOBASE ELECTRONICS MBECFOB2402 Manuel utilisateur

Marque
MOBASE ELECTRONICS
Modèle
MBECFOB2402
Taper
Manuel utilisateur
4. USER MANUAL
4.1 ITEM : FOB LF system
- This system is SCIM and inculdes RKE.
- RKE in SCIM system is intended for auto door lock or unlock or TRUNK in vehicle.
- This SMK system is to be installde on motor vehicles as *OE item.
*OE : Original Equipment.
*SCIM : Security & Cab Interface Module
*RKE : Remote Keyless Entry.
4.2 SYSTEM CONSTRUCTION
4.2.1 SYSTEM IN VEHICLE
4.2.2 SYSTEM FOR TEST
① Connect the 24V power supply and turn on the switch
② Pressing the white tact switch, LF signal is transmitted and FOB LED and IBU LED is flahes
③ When the tact switch is pressed repeatively, FOB LED and SCIM LED is flahes, repeatively.
* It shows the status of operation through the LED used.
Radio Frequency
(433.92MHz)
ANTENNA
BATTERY
LF ANT
SCIM
Low Frequency
(125KHz)
SSB
Radio Frequency
(433.92MHz)
ANTENNA
BATTERY
LF ANT
SCIM
Low Frequency
(125KHz)
Switch
LED
FCC warning statement:
15.19
λ. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
15.105
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does
cause harmful interference to radio or television reception, which can be determined by turning the
equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
15.21
- Any changes or modifications not expressly approved by the party responsible for compliance could void the
authority to operate equipment.
- This device and its antenna must not be co-located or operating in conjunction with any other antenna or
transmitter.
- End-users and installers must be provided with antenna installation instructions and transmitter operating
conditions for satisfying RF exposure compliance.
FCC/ IC RF Radiation Exposure Statement:
This device complies with FCC/ ISED radiation exposure limits set forth for an uncontrolled environment.
IC warning statement:
RSS-Gen Issue 4 8.4
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two
conditions: (1) This device may not cause interference; and (2) This device must accept any interference,
including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de
licence.
L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et
(2)
l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible
d'en compromettre le fonctionnement.
Industry Canada ICES-003 Compliance Label:
CAN ICES-3
Co-located
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or
transmitter.
  • Page 1 1
  • Page 2 2

MOBASE ELECTRONICS MBECFOB2402 Manuel utilisateur

Marque
MOBASE ELECTRONICS
Modèle
MBECFOB2402
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents