GE RAK190V Le manuel du propriétaire

GE
Marque
GE
Modèle
RAK190V
Catégorie
Thermostats
Taper
Le manuel du propriétaire
SPECIFICATIONS ..............................2
INSTALLATION INSTRUCTIONS
WIRING ...........................................5
INSTALLER MENU .......................10
USING THE THERMOSTAT
OVERVIEW ................................... 14
TROUBLESHOOTING ....................... 15
RESETTING ................................... 15
WARRANTY ..................................... 17
FCC STATEMENT ............................ 18
THERMOSTAT
Energy Management
INSTALLATION INSTRUCTIONS
RAK190V
31-5000842 Rev. 0 09-23
231-5000842 Rev. 0
SPECIFICATIONS
MERCURY NOTICE: This product does not contain mercury.
However, this product may replace a product that contains
mercury. Mercury and products containing mercury must not be
discarded in household trash. Refer to thermostat-recycle.org
for information on disposing of products containing mercury.
Electrical Rating:
Input-Hardwire 24 VAC (18-30 VAC)
Load -1 amp maximum per output
-4 amp maximum total load
Setpoint Range 60° to 85° F (16° to 29° C)
Operating Ambient 40º F to 99º F (4º C to 37º C)
Occupancy Sensor Range 5 meters, 109.6 degrees x 109.6 degrees
Field of View
O1/O2 Dry Contact Ratings .5A @ 32VAC or .5A @ 30VDC
Humidity Range/Accuracy 0 to 95% operating humidity range, +/- 5%
accuracy
Shipping Temperature
Range -30°F to + 150°F (-34° to +65°C)
Thermostat Dimensions 3.9” H x 5.4” W x 1.03”
Thermostat Applications Maximum Stages Heat/ Cool
Single Stage Cooling, One or Two
Stage Heating
NOTE: Two stage heating = 1st
stage heat pump and 2nd stage
resistance heat
3/2
Two Stage Cooling, Three Stage
Heating
NOTE: Three stage heating = 2
stage heat pump and 3rd stage
resistance heat
2-Way Communication with select
GE Appliance products
31-5000842 Rev. 0 3
PACKAGE CONTENTS/TOOLS REQUIRED:
Package includes:
• Thermostat base
• Thermostat
• Screws
• Wall anchors
Tools needed:
'ULOOZLWKƎELW
• Hammer
• Screwdriver
• Putty
WARNING
ELECTRICAL SHOCK HAZARD — Turn off power by
unplugging the unit or by removing the fuse or switching
the appropriate circuit breaker to the OFF position before
removing the existing thermostat. Failure to do so could
result in risk of electric shock.
INSTALLATION INSTRUCTIONS
TO REMOVE EXISTING THERMOSTAT
1. Turn off power to heating and cooling system by removing the fuse or
switching off the appropriate circuit breaker.
2. Remove cover of old thermostat. This should expose the wires.
3. Remove wires from wire terminals. Note which color wires are attached
to each terminal.
4. Remove existing thermostat base from wall.
5. Refer to the following section for instructions on how to install this
thermostat.
431-5000842 Rev. 0
TO INSTALL THERMOSTAT
IMPORTANT: Thermostat installation must conform to local
and national building and electrical codes and ordinances.
NOTE: Mount the thermostat about five feet above the floor. Do not mount
the thermostat on an outside wall, in direct sunlight, behind a door or in an
area affected by a vent or duct.
1. Turn off power to the heating and cooling system by removing the fuse
or switching off the appropriate circuit breaker.
2. Loosen (do not remove) the screw on the bottom of the thermostat
assembly to remove thermostat from base.
3. Put thermostat base against the wall where you plan to mount it.
Make sure wires will feed through the wire opening in the base of the
thermostat. Ensure enough clearance to dress excess wire slack.
4. With the base level, mark the placement of the mounting holes.
5. Set thermostat base and thermostat away from working area.
6.8VLQJDƎGULOOELWGULOOKROHVLQWKHORFDWLRQV\RXKDYHPDUNHGIRU
mounting.
7. Use a hammer to tap supplied anchors in mounting holes.
8. Align thermostat base with mounting holes and feed the control wires
through the wire opening.
9. Seal hole for wires behind thermostat with non-flammable insulation
or putty, or use a wall plate obtainable from a local hardware or home
building store.
10. Use supplied screws to mount thermostat base to wall.
11. Insert stripped wires in matching wire terminals by pressing on the
corresponding terminal contact. See the “Wiring” section of this manual.
NOTICE
Make sure exposed portion of wires do not touch other wires.
12. Gently tug wire to be sure of proper connection. Double check that
each wire is connected to the proper terminal.
13. Replace thermostat by snapping it in place and tighten bottom screw.
14. Plug the unit in or turn on power to the system at the main service
panel.
15. Test thermostat operation in all modes (fan only, cooling, heating and
both fan speeds).
INSTALLATION INSTRUCTIONS
31-5000842 Rev. 0 5
INSTALLATION INSTRUCTIONS
WIRING
Refer to equipment manufacturer’s instructions for specific system wiring
information. After wiring, see INSTALLER MENU for proper thermostat
configuration. Wiring table shown are for typical systems and describe the
thermostat terminal functions.
Precautions
• Do not exceed the specification ratings.
• All wiring must conform to local and national electrical codes and
ordinances.
• This control is a precision instrument, and should be handled carefully.
Rough handing or distorting components could cause the control to
malfunction.
To prevent electrical shock and/or
equipment damage, disconnect electrical
power to system, at main fuse or circuit
breaker box,until installation is complete.
CAUTION
Do not use on circuits exceeding specified
voltage. Higher voltage will damage control and
could cause shock or fire hazard.
Do not short out terminals on primary control
to test. Short or incorrect wiring will burn out
thermostat and could cause personal injury and/
or property damage.
WARNING
631-5000842 Rev. 0
RS
485 B
-A
+CRY
2G
LG
HBYWSS
CO2
+O2
CO1 O1
C
2- WAY STANDARD OUTPUTS
Brown - RS485 GND
White/Blue - Data B-
Blue - Data A+
Black - Common
Red - R – 24V AC
INSTALLATION INSTRUCTIONS
Diagram 1: 2-Way Communication Wiring (5 Wire)
Note: 2-way communication provides 2-way capable
equipment with temperature & humidity data to
optimize performance.
A link icon (see page 14) will be displayed on the
thermostat when a successful 2-way connection has
been made.
For make up air models: To deliver make-up air only
when a room is occupied, be sure to enable mode
“E” in the auxiliary controls of the air conditioner.
Note: Colors Mentioned on Diagram Match Leads
on Zoneline 2-Way Connector below.
31-5000842 Rev. 0 7
INSTALLATION INSTRUCTIONS
RS
485 B
-A
+CRY
2G
LG
HBYWSS
CO2
+O2
CO1 O1
C
2- WAY STANDARD OUTPUTS
Low Fan
High Fan
Reversing Valve
Common
24V AC
Compressor
Aux Heat
2nd Stage Compressor
Diagram 2: Standard Communication Wiring (3 Heat
/ 2 Cool), Factory Default
831-5000842 Rev. 0
RS
485 B
-A
+CRY
2G
LG
HBYWSS
CO2
+O2
CO1 O1
C
2- WAY STANDARD OUTPUTS
Low Fan
High Fan
Reversing Valve
Common
24V AC
Compressor
Aux Heat
OpƟonal: Occ Out
INSTALLATION INSTRUCTIONS
Diagram 3: Standard Communication Wiring (2 Heat
/ 1 Cool)
Note: With single stage compressor
configuration, Y2 can be used as
an occupancy out signal to control
make-up air delivery based on
occupancy (if needed)
31-5000842 Rev. 0 9
INSTALLATION INSTRUCTIONS
Note: With single stage compressor
configuration, Y2 can be used as
an occupancy out signal to control
make-up air delivery based on
occupancy (if needed)
RS
485 B
-A
+CRY
2G
LG
HBYWSS
CO2
+O2
CO1 O1
C
2- WAY STANDARD OUTPUTS
Low Fan
High Fan
Common
24V AC
Compressor
Aux Heat
OpƟonal: Occ Out
Diagram 4: Standard Communication Wiring (1 Heat
/ 1 Cool)
10 31-5000842 Rev. 0
INSTALLER MENU
To access the INSTALLER MENU, use the Power button to turn the
thermostat OFF. While OFF, press and hold the Mode and + button for 2
seconds until “Setup Mode” is shown on the display.
Once in the menu:
•+ / – : change setting selection
• Mode: advances to next menu item
•Fan: returns to previous menu item
• Power: saves changes and exits
Note: After two minutes of no key presses, Menu times out and returns to
Power Off black screen.
INSTALLATION INSTRUCTIONS
Indicator
confirms
you are
in setup
mode
Two Small
Digits =
Menu Item
Selection
Two Large
Digits =
Setting
Selection
31-5000842 Rev. 0 11
INSTALLER MENU (cont)
INSTALLATION INSTRUCTIONS
Menu Item
(Mode advances
to next, Fan
returns to
previous)
Description Default
Setting
Range/
Selections
(+ or - to
change)
8 Wire
Setting
Availability
2- Way
Setting
Availability
01 Units (F=Fahrenheit or C=
Celsius) F F, C X
02
Set Current Hours (military
time)
Only used if Scheduling Energy
Savings (setting 20)
00 to 23X X
03 Set Current Minutes
Only used if Scheduling Energy
Savings (setting 20) 00 to 59X X
06
Fan Mode
A = Auto, only allows auto
(cyclic) fan selection in heating/
cooling modes
C = Continuous, allows
selection of continuous or
auto (cyclic) in heating/cooling
modes
CA, C X
07 Heat Pump
Is the unit a heat pump? Y=
Yes, n= No YY, n X
08 Reversing Valve Type bb, O X
09 Number of Compressor
Stages 21, 2 X
10
Heating Differential 1
Number of degrees (F) from set
point required to activate 1st
stage heat
11 to 10X
11
Cooling Differential 1
Number of degrees (F) from set
point required to activate 1st
stage cool
11 to 10X
12
Heating Differential 2
Number of degrees (F) from 1st
stage heat required to activate
2nd stage heat
11 to 10X
13
Cooling Differential 2
Number of degrees (F) from 1st
stage cool required to activate
2nd stage cool
11 to 10X
14
Heating Differential 3
Number of degrees (F) from 2nd
stage heat required to activate
3rd stage heat
11 to 10X
15 Auto Changeover
Y = enables autochangeover
option under "Mode" nn, Y X
12 31-5000842 Rev. 0
INSTALLER MENU (cont)
INSTALLATION INSTRUCTIONS
Menu Item
(Mode advances
to next, Fan
returns to
previous)
Description Default
Setting
Range/
Selections
(+ or - to
change)
8 Wire
Setting
Availability
2- Way
Setting
Availability
16
Deadband (F)
This offset is added to both
Cooling & Heating Differential 1
when in autochangeover mode
Note: Setting is only available if
autochangeover is enabled
11 to 10X
17 Min Cooling Temp (F)
Note: Can't be a higher
temperature than setting 18 66 60, 64, 66,
68, 70, 72,
74, 76 X
18 Max Heating Temp (F)
Note: Can't be a lower
temperature than setting 17 78 65, 70, 72,
74, 76, 78,
80, 85 X
19
Room Temp Offset (F)
If needed, this is an offset to
calibrate room temperature
reading
0-9 to 9X X
20 Humidity Offset
If needed, this is an offset to
calibrate room humidity reading 0-9 to 9X X
21
Occupancy Energy savings
OF = No temperature setbacks
are allowed
Y = Temperature setbacks are
allowed when no occupancy is
detected
S = Scheduled Energy Savings.
Temperature setbacks are only
allowed in the time window
specified by settings 29 and 30.
Y OF, Y, S X X
22 Occupancy Response Time
(tenths of a second) 1 0-30 X X
24
Occupancy Cool Setback
Temperature
The number of degrees (F) the
temperature is allowed to drift
above setpoint in cooling with
no occupants detected
Note: Only Available if
Occupancy Energy Savings
(setting 21) is set to Y or S
3 0-15 X X
25
Occupancy Heat Setback
Temperature
The number of degrees (F) the
temperature is allowed to drift
below setpoint in heating with
no occupants detected
Note: Only Available if
Occupancy Energy Savings
(setting 21) is set to Y or S
3 0-15 X X
26 Not Used - For Future Use 50-15 X
27 Not Used- For Future Use 50-15 X
31-5000842 Rev. 0 13
INSTALLER MENU (cont)
INSTALLATION INSTRUCTIONS
Menu Item
(Mode advances
to next, Fan
returns to
previous)
Description Default
Setting
Range/
Selections
(+ or - to
change)
8 Wire
Setting
Availability
2- Way
Setting
Availability
28
Occupancy Status Timer (in
minutes)
The number of minutes
occupancy status is maintained
once an occupancy event
occurs
Note: Only Available if
Occupancy Energy Savings
(setting 21) is set to Y or S
30 0-99(100)
by 5’s XX
29
Scheduled Energy Savings
Start Time (military time)
If using Scheduled Energy
Savings, select the start
time when occupancy driven
setbacks are permitted.
Note: Only Available if
Occupancy Energy Savings
(setting 21) is set to S
9 0-23 X X
30
Scheduled Energy Savings
Stop Time (military time)
If using Scheduled Energy
Savings, select the time when
occupancy driven setbacks are
no longer permitted
Note: Only Available if
Occupancy Energy Savings
(setting 21) is set to S
21 0-23 X X
31
Device 1
Used to control external relay
wired to O1 output on terminal
block
OF
OF - OFF
nO - normally
open,
occupancy
event closes
circuit
nC- normally
closed,
occupancy
event opens
circuit
rO - not used
rC - not used
XX
32
Device 2
Used to control external relay
wired to O2 output on terminal
block
OF X X
99
Defaults Reset
Selecting Y restores all
programming defaults after
leaving the Installer Menu
nn, Y X X
14 31-5000842 Rev. 0
USING THE THERMOSTAT
THERMOSTAT OVERVIEW
Before you begin using your thermostat, you should be familiar with its
features, display and the location/operation of the thermostat buttons.
THERMOSTAT BUTTONS AND SWITCHES THE DISPLAY
1.) Power 6.) Selected Setpoint
2.) Fan Selection
– 2-way options: Low, High (auto or continuous based on
Zoneline Auxiliary Mode #1 selection)
– 8 wire options: Auto Low, Auto High, Low and High (if
“C” is enabled in thermostat setting 6)
7.) 2-Way Communication Indicator
Solid Link = Connected
Blinking Link = Connection Issue
3.) Mode Selection
– 2-way options: Heat, Cool Fan
– 8 wire options: Heat, Cool, Fan, Auto (Autochangeover)
*Note: Auto must be enabled in setting 15 to be an
available option
4.) Lower Setpoint
5.) Raise Setpoint
31-5000842 Rev. 0 15
TROUBLESHOOTING
Problem Solution
No Display Press power button to ensure thermostat isn’t off.
Check for 24 VAC; display is blank when 24 VAC is
not present
System fan does not
come on properly Verify that wiring is correct.
All thermostat buttons
are inoperative Verify that 24 VAC is present; unit will not operate
when 24 VAC is not present.
Thermostat turns on and
off too frequently Adjust temperature differential (see Configuration
Mode - Setting Temperature Differential, Stage 1,
Stage 2, and Stage 3 section).
Fan runs continuously Check fan selection. If set to High or Low in 8-wire
mode, fan will run continuously. If thermostat is in
2-way control mode, verify the Auxiliary settings of
the Zoneline HVAC unit.
Compressor doesn’t run
or turn off immediately
when changing function
or setting
There is a 3 minute time delay and a 3 minute
minimum run time for the compressor when it turns
on/off.
Fan doesn’t run or turn
off immediately when
changing function or
setting
This is normal. On some models, the fan may have
a minimum run time/off time delay.
Resetting the Thermostat or Thermostat Settings
To conveniently reset only the user settings back to factory defaults, see
setting 99 in the Installer Menu.
This product contains a chemical known to the state of California to cause
cancer and birth defects and other reproductive harm.
WARNING
16 31-5000842 Rev. 0
NOTES
31-5000842 Rev. 0 17
What GE Appliances Will Not Cover:
Ŷ Service trips to your location.
Ŷ Improper installation. If you have an installation problem, contact
your installer. You are responsible for providing adequate electrical
connections to the product.
Ŷ Failure of the product resulting from modifications to the product or
due to unreasonable use, including failure to provide reasonable and
necessary maintenance.
Ŷ In commercial locations, labor necessary to move the unit, after it has
been initially installed, to a location where it is accessible for service by
an individual technician; or, if the instructions included in this manual
have been disregarded.
Ŷ Replacement of location fuses or the resetting of circuit breakers.
Ŷ Damage to the product caused by improper power supply voltage,
accident, fire, floods or acts of God.
Ŷ Incidental or consequential damage caused by possible defects with this
thermostat.
Staple your receipt here.
Proof of the original purchase date is needed to validate the warranty.
This warranty is extended to the original purchaser and any succeeding
owner for products purchased for use within the USA and Canada.
In Alaska, the warranty excludes the cost of shipping or service calls to
your site.
Some states or provinces do not allow the exclusion or limitation of
incidental or consequential damages. This warranty gives you specific legal
rights, and you may also have other rights which vary from state to state or
province to province. To know what your legal rights are, consult your local,
state or provincial consumer affairs office or your state’s Attorney General.
EXCLUSION OF IMPLIED WARRANTIES—Your sole and exclusive
remedy is product exchange as provided in this Limited Warranty.
Any implied warranties, including the implied warranties of
merchantability or fitness for a particular purpose, are limited to
one year or the shortest period allowed by law.
Warrantor: GE Appliances, a Haier company
Louisville, KY 40225
LIMITED WARRANTY
For The Period Of GE Appliances Will Replace :
One Year From the date of
the original purchase Full Replacement of the thermostat
which fails due to a defect in materials or
workmanship. For Warranty replacement,
contact your distributor.
18 31-5000842 Rev. 0
FCC STATEMENT
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and
receiver
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician
for help CAN ICES-003 (B) / NMB-003 (B)
SPÉCIFICATIONS ..............................2
INSTALLATION DU THERMOSTAT
CÂBLAGE .......................................5
MENU DE L’INSTALLATEUR .......10
UTILISATION DU THERMOSTAT
APERÇU DU THERMOSTAT .........14
DÉPANNAGE ................................... 15
RÉINITIALISATION ....................... 15
GARANTIE : ..................................... 17
DÉCLARATION DE LA FCC : ........... 18
THERMOSTAT
Gestion de l’énergie
INSTRUCTIONS D’INSTALLATION
RAK190V
31-5000842 Rev. 0 09-23
231-5000842 Rev. 0
SPÉCIFICATIONS
AVIS RELATIF AU MERCURE : Ce produit ne contient pas de mercure. Il
peut toutefois remplacer un produit qui en contient. Le mercure et les produits
contenant du mercure ne doivent pas être jetés dans les ordures ménagères.
Consultez le site thermostat-recycle.org pour connaître les endroits où vous
pouvez envoyer le produit contenant du mercure.
Paramètres électriques :
Câblé 24 VAC (18-30 VAC)
Charge - 1 ampère maximum par sortie
- 4 ampères maximum, charge totale
Plage de réglage 60°F à 85°F (16°C à 29°C)
Température ambiante de
fonctionnement 40 °F à +99 °F (4 à +37 °C)
Portée du capteur d’occupation 5 mètres, champ de vision de 109,6 degrés x
109,6 degrés
Valeurs nominales de contact sec
O1/O2 0,5 A @ 32 VCA OU 5 A @ 30 VCC
Plage d’humidité/précision Plage d’humidité de fonctionnement de 0 à
95 %, précision de +/- 5 %
Plage de températures
d’expédition -30 °F à + 150 °F (-34 à +65 °C)
Dimensions du thermostat 3.9 po H x 5.4 po L x 1.03 po P
Applications du thermostat Nombre maximum d’étages chauffage/
climatisation
Refroidissement à une étape, chauffage
à une ou deux étapes – REMARQUE :
Chauffage à deux étages = 1er étage
par thermopompe et 2e étage par
résistance.
3/2
Refroidissement à deux étages,
chauffage à trois étages
Remarque : Chauffage à trois étages =
thermopompe à 2 étages et chauffage
par résistance au 3e étage
Communication à 2 voies avec certains
produits GE Appliance
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36

GE RAK190V Le manuel du propriétaire

GE
Marque
GE
Modèle
RAK190V
Catégorie
Thermostats
Taper
Le manuel du propriétaire
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents