GE RAK180W1 Le manuel du propriétaire

THERMOSTAT

Wireless Thermostat with Occupancy Sensor

OWNER’S MANUAL &

INSTALLATION INSTRUCTIONS

RAK180W1

49-5000416 Rev. 1 07-19 GEA

F

2 49-5000416 Rev. 1

THANK YOU FOR MAKING GE APPLIANCES A

PART OF YOUR HOME.

Whether you grew up with GE Appliances, or this is

your first, we’re happy to have you in the family.

We take pride in the craftsmanship, innovation and

design that goes into every GE Appliances product,

and we think you will too.

49-5000416 Rev. 1 3

Table of Contents

Safety Information ............................................................................................................ 4

Before You Begin .................................................................................................................5

Thermostat Installation .................................................................................................... 7

Installing the Wireless Control card ........................................................................................7

Wireless Installation ...............................................................................................................10

Wired Installation ....................................................................................................................10

Thermostat Configuration ............................................................................................11

Setting the clock .....................................................................................................................12

Entering the room number ....................................................................................................13

Configuring the Equipment Settings - Compressor Type ....................................................14

Configuring the Equipment Settings - Electric Heat ............................................................15

Configuring the Equipment Settings - Reversing Valve ......................................................16

Configuring the Energy Saving Settings...............................................................................17

Custom Energy Savings Settings .............................................................................. 19

Using the Thermostat Settings Screens ...............................................................................20

01 – FAN CONTROL MODE ................................................................................................21

02 – 1ST STAGE DIFFERENTIAL - HEAT .........................................................................22

03 – 2ND STAGE DIFFERENTIAL - HEAT ........................................................................23

04 – 1ST STAGE DIFFERENTIAL - COOL ........................................................................24

05 – INCIDENTAL OCCUPANCY THRESHOLD ...............................................................25

06 – NIGHT OCCUPANCY THRESHOLD ..........................................................................26

07 – FORCED 2ND STAGE HEATING ...............................................................................27

08 – NIGHT OCCUPANCY START .....................................................................................28

09 – NIGHT OCCUPANCY END .........................................................................................29

10 – TEMPERATURE RECOVERY TIME ..........................................................................30

11 – RECOVERY TEMPERATURE - HEAT .......................................................................31

12 – TEMPERATURE SETBACK DELAY - HEAT .............................................................32

13 – MINIMUM SETBACK TEMPERATURE ......................................................................33

14 – TEMPERATURE SETBACK DELAY - COOL ............................................................34

15 – MAXIMUM SETBACK TEMPERATURE.....................................................................35

16 – RECOVERY TEMPERATURE - COOL ......................................................................36

17 – MINIMUM SET POINT .................................................................................................37

18 – MAXIMUM SET POINT ................................................................................................38

19 – TEMPERATURE CONTROL MODE ...........................................................................39

20 – AUTO CHANGEOVER SET POINT OFFSET

(DEAD BAND) ...............................................................................................................40

21 – SETBACK SET POINTS / AUTO-RESTORE .............................................................41

22 – AUTOMATIC HUMIDITY CONTROL† ........................................................................42

23 – TEMPERATURE CALIBRATION.................................................................................43

Thermostat Maintenance .............................................................................................44

Troubleshooting ................................................................................................................45

Appendix 1 - Energy Saving Presets ......................................................................48

Technical Specifications ..............................................................................................49

Limited Warranty ..............................................................................................................50

4 49-5000416 Rev. 1

Specifications.

WARNING

FIRE AND SHOCK HAZARD

• Always turn off power at the main power supply

before installing, cleaning or removing the

thermostat. Failure to do so could result in

electrical shock hazard.

• Do not use on voltages over 30 VAC. Higher

voltages will damage the thermostat and could cause

shock or fire hazard.

NOTICE

• All wiring must conform to local and national

electrical and building codes.

• Use this thermostat only as described in this manual.

Electrical rating: • 24 VAC (18–30 VAC)

• 1 amp maximum per terminal

• 4 amp maximum total load

Operating temperature range: 40°F–99°F (4°C–37°C)

System Configurations:

* 1 stage cool, 2 stage heat (heat pump/resistance heat)

1 stage cool, 1 stage heat (resistance heat)

Terminations: *R, C, W, Y, GH, GL, B for 2-stage heat

R, C, W, Y, GH, GL, for 1-stage heat

Wiring:

Maximum wiring length is 66ft (20 meters) for

AWG18

Maximum wiring length is 60ft (18 meters) for

AWG20

*Default setting

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING

49-5000416 Rev. 1 5

Before You Begin

• Determine the appropriate installation location for the

thermostat

The thermostat should face the bed area of the

room.

The thermostat must not be installed near or on

metal structures or surfaces including metal air

ducting that may be in the wall.

0HWDOVWUXFWXUHVDQGVXUIDFHVVLJQL¿FDQWO\

reduce the range of the wireless signal.

A. Refer to the Zoneline Owner’s Manual to change

the AUX setting to 6A (class 2 mode). The unit will

display “use wall thermostat” when finished.

B. Zoneline output is 24VAC. Be sure the jumper on the

wireless control card is on the AC position – jumper

is connecting “R” and “C” (common) pins. This is the

default position.

Other Zoneline Auxilary Control Settings for use with

*DBM & *EBM Models

• Mode E: Enables Zoneline Makeup air vent door control

EDVHGRQRFFXSDQF\GHIDXOWLVRႇDQGPRGHPXVWEH

turned on to utilize this feature.

• Refer to the Zonelines Owner’s Manual for instructions

on how to change this AUX setting/mode.

6 49-5000416 Rev. 1

NETWORK INSTALLATION ONLY

NOTE: This section is not required unless the thermostats are

networked

Pairing the Thermostat and the Control Card:

In case of Network Installation with online management, the

thermostat and the Control Card must be paired with a Network

Programmer specific to the property before the installation.

Note: Thermostat and Control Card are factory paired.

The thermostat and control card must not be powered during the

pairing procedure - remove batteries from the thermostat and unplug

the control card from the HVAC unit during the pairing procedure.

• Plug one programmer connector into the thermostat;

• Plug the other programmer connector into the control card.

• Push the black button on the programmer.

•

The red light on the programmer should turn on and remain

steadily lit.

•

If the red light on the programmer is blinking or is not steadily

lit, unplug the programmer from the thermostat and the control

card and repeat the steps above.

• Unplug the programmer from the thermostat and the control card.

Thermostat

Network

Programmer

Connector

Control

Card

49-5000416 Rev. 1 7

Thermostat Installation

Installing the Wireless Control Card

• Power off the Zoneline

• Insert the Control Card wiring harness into the thermostat

connection port on the front of the Zoneline control box cover.

• For Makeup Air Models (*DBM and *EBM), insert the small

connector into the mating CDC Connection port next to the

thermostat port. (See Drawing 1)

NOTE: If not a Makeup Air Model, DO NOT plug in the CDC/

occupancy connection.

AC input

CDC /

Occupancy

Connection

Remote

Thermostat

Connection

Red Aux Set

Button

Drawing 1

8 49-5000416 Rev. 1

Thermostat Installation

Installing the Wireless Control Card (cont.)

• Using the supplied double sided tape, attach the control card

to the Zoneline control box cover. (See Drawing 2)Mount the

control card inside of the hvac unit.

The wireless control card antenna must not be touching any metal

components of the hvac unit.

The wireless control card antenna must face the thermostat on the

wall and be oriented so that any metal parts of the Zoneline do not

obstruct the wireless communication to the thermostat and, in case of

a network installation, to other wireless control cards and the server.

The wireless control card must not be placed in the Zoneline

condensation pan and must be mounted so it cannot fall into the

condensation pan.

• For wired applications, join the common and 24VAC wires with

any code-approved low voltage field supplied connection method.

CDC/

Occupancy

Remote

Thermostat

Connection

Control

Card

Drawing 2

49-5000416 Rev. 1 9

Thermostat Installation

Wire Color Terminal Letter Terminal Connection

Black C Common

Red R 24V

Yellow Y Compressor

White W Heat

Orange O or B Reversing Valve

Green GH Fan High

Purple GL Fan Low

Brown AUX Occupancy

NOTE: If the PTAC unit has only one (1) fan speed,

connect both fan control wires – Green and Purple –

to the fan terminal (G).

Wiring Table – 24V AC

10 49-5000416 Rev. 1

Thermostat Installation

Wireless Installation

GH OB W R Y C

AUX

GL

F

Mounting the thermostat to the wall

• Remove the thermostat cover;

• Use the supplied wall anchors and mounting screws to

secure the thermostat to the wall;

• Insert two (2) AA-cell batteries (not supplied) into the

thermostat battery compartment;

• Follow the “Thermostat Configuration” instructions

starting on page 11.

• Replace the thermostat cover and screw in the locking

screw.

Wired Installation

GH OB W R Y C

AUX

GL

R C

F

Mounting the thermostat to the wall

• Connect R & C from HVAC unit to the corresponding

wires on the harness by splicing 24VAC and common

wires from the thermostat into the 24VAC and common

wires to the zoneline.

• Remove the thermostat cover;

• Use the supplied wall anchors and mounting screws to

secure the thermostat to the wall;

• Follow the “Thermostat Configuration” instructions

starting on page 11.

• Replace the thermostat cover and screw in the locking

screw.

49-5000416 Rev. 1 11

Thermostat Configuration

Once the thermostat is powered, thermostat configuration

settings will appear on the thermostat screen.

In order to properly operate the HVAC unit:

• Set the thermostat clock

• Enter the room number

• Configure the equipment settings

• Select Energy Savings Preset (Zoneline custom settings

are the default).

The thermostat configuration screens have a 30-second

time-out. If no action is taken within thirty (30) seconds, the

thermostat will exit configuration settings.

NOTE: You can

access Thermostat

Configuration settings at

any time by pressing the

“Configuration” button.

NOTE: If the thermostat is connected to a network, the

settings configured online will be applied.

12 49-5000416 Rev. 1

Thermostat Configuration

Setting the thermostat clock

Set the thermostat clock to current time in 24h (Military Time)

format.

• Use the “Up” and “Down” buttons to set the hours

• Press the “Fan” button to advance to the minutes setting

• Use the “Up” an “Down” buttons to set the minutes

• Press the “F/C” button to advance to the next menu

Setting the clock correctly is crucial for proper operation of

the thermostat.

NOTE:

The thermostat clock will need to be reset each time

the batteries are replaced.

Hours

Minutes

49-5000416 Rev. 1 13

Thermostat Configuration

Entering the room number

Enter the room number by changing the digits on the screen.

Leading zeros “0” preceding other digits will be ignored, i.e.

Room number “123” should be entered as “00123”.

• Use the “Up” and “Down” buttons to change the digit;

• Press the “Fan” button to advance to the next digit;

• Press the “F/C” button to advance to the next menu;

Entering the room number correctly is crucial for proper

operation of networked systems.

14 49-5000416 Rev. 1

Thermostat Configuration

Configuring the Equipment Settings - Compressor Type

Use the “Up” and “Down” buttons to change the compressor

type by changing the first digit

0 - No Compressor

1* - Heat pump

2 - Air Conditioner

• Press the “Fan” button to advance to the next setting;

* Indicates default setting

NOTE:

If the Zoneline is an AZ45 model, change the

compressor type to a 2.

Compressor Type

49-5000416 Rev. 1 15

Thermostat Configuration

Configuring the Equipment Settings - Electric Heat

Use the “Up” and “Down” buttons to change the Electric Heat

setting by changing the second digit;

0 - No Electric Heat- All Zonelines have Electric heat -

Do not select this option.

1* - Electric Heat

• Press the “Fan” button to advance to the next setting;

* Indicates default setting

Electric Heat

16 49-5000416 Rev. 1

Thermostat Configuration

Configuring the Equipment Settings - Reversing Valve

Use the “Up” and “Down” buttons to change the reversing

valve type by changing the first digit

0 - OB contact is energized to cool

1* - OB contact is energized to heat (default operation for

Zoneline heat pump models)

Refer to the HVAC unit documentation to determine the

correct OB VALVE setting.

If incorrect OB VALVE Setting is selected, the HVAC

unit will turn on the heating when air conditioning is

requested and turn on the air conditioning when heating is

requested.

• Press the “F/C” button to advance to the next menu

• Press the “Fan” button to advance to toggle to equipment

settings.

* Indicates default setting

NOTE: Zonelines OB is energized in heating mode.

Reversing Heat

49-5000416 Rev. 1 17

Thermostat Configuration

Configuring the Energy Saving Settings

Use the “Up” and “Down” buttons to select the Energy Saving

preset:

E-C*: Custom Energy Savings

•

Refer to the APPENDIX 1 on page 48 for Energy Saving

Preset details.

• For details on changing the custom settings, refer to the

“Custom Energy Savings Settings” section on page 19.

E-0: Energy Savings Off - No Temperature Setback;

E-1: Lowest Energy Savings;

E-2: Lower Energy Savings;

E-3: Standard Energy Savings;

E-4: Higher Energy Savings;

E-5: Highest Energy Savings;

• Press the “Power” button to save the Thermostat

Configuration and start using the thermostat.

* Indicates default setting

18 49-5000416 Rev. 1

Thermostat Configuration

Testing the thermostat

Following the thermostat configuration, test if the thermostat

is controlling the Zoneline unit.

• Press the “Power” button to turn the thermostat ON;

• Press the “Down” button to change the temperature set

point below the current room temperature to confirm that

the thermostat initiates air conditioning.

• Press the “Up” button to change the temperature set point

above the current room temperature to confirm that the

thermostat initiates heating.

• Change the fan speed by touching the “Fan” button to test if

the thermostat is controlling the fan speed.

49-5000416 Rev. 1 19

Custom Energy Savings Settings

This thermostat comes preprogrammed to use a custom

energy setting. To change any of these presets, follow the

instructions below.

Accessing the Thermostat Settings

With the thermostat turned on, press and hold the

“Configuration” button until the first thermostat settings screen

appears. The thermostat must be turned on to access the

thermostat settings.

³&RQ¿JXUDWLRQ´EXWWRQ

NOTE: If the thermostat is connected to a network, the

settings configured online will be applied.

• Use the “Up” and “Down” buttons to change the setting;

• Press the “F/C” button to advance to the next setting;

• Press the “Fan” button to return to the previous setting;

• Press the “Power” button to save and exit thermostat

settings.

20 49-5000416 Rev. 1

Custom Energy Savings Settings

Using the Thermostat Settings Screens

• Use the “Up” and “Down” buttons to change the setting.

• Press the “F/C” button to advance to the next setting.

• Press the “Fan” button to return to the previous setting.

• Press the “Power” button to save and exit thermostat

settings.

The above is a representation of how to read the

digits on the thermostat screen.

Setting Value

Screen Number

La page charge ...

GE RAK180W1 Le manuel du propriétaire

GE RAK180W1 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents