Honeywell CT40 XP Mode d'emploi

Marque: Honeywell

Modèle: CT40 XP

Catégorie: Les smartphones

Taper: Mode d'emploi

CT40/CT40 XP Series

Quick Start Guide

CT40-A-EN-QS-01 Rev H

09/22





Out of the Box

Make sure that your shipping box contains these items:

• Mobile Computer

Model CT40-L0N, CT40-L1N, CT40P-L0N, or CT40P-L1N

• Rechargeable Li-ion battery (see page 7)

•Hand strap

• Product documentation

If you ordered accessories for your mobile computer, verify that

they are also included with the order. Be sure to keep the original

packaging in case you need to return the mobile computer for

service.

Note: CT40-L0N/CT40P-L0N models do not include a WWAN radio.

Memory Card Specifications

Honeywell recommends the use of Single Level Cell (SLC)

industrial grade microSD™ or microSDHC™ memory cards with

mobile computers for maximum performance and durability.

Contact a Honeywell sales representative for additional

information on qualified memory card options.

Mobile Computer Features

Microphone

Power Button

Battery Status/

Notification LED

Speaker

Touch Panel

Scan Button

Microphone

Speaker

Scan Status LED

Scan Button

Imager Window

(LED/Laser Aperture)

Push-to-Talk

Button

(model dependent)

Front Facing Camera

(model dependent)

Note: Hand strap not shown.

Scan Button

Volume Button

Camera Lens

and Flash

Laser Safety

Label Location

SIM Card Door

MicroSD Card Door

I/O Connector

Audio Jack Pin

(model dependent)

USB, Type C

(model dependent)

BLE Speaker Out

(model dependent)

Battery Latch (Models

CT40-L0N-xxxxxAx,

CT40-xxx-xxxxxBx,

CT40-xxx-xxxxxHx, and

all CT40XP)

Battery

(Refer to page 7)

Battery Latch (Model

CT40-xxx-xxxxx0x)

Install a microSD Card (Optional)

Note: Format the microSD card before initial use.

Note: Always power off the computer before attempting to install or

remove a card.

Install a microSIM Card

Note: Phone feature is only available on CT40-L1N/CT40P-L1N

models. On all models, the SIM slot supports use of a UICC card for

NFC Secure Element NFC link encryption.

Note: Always power off the computer before attempting to install or

remove a card.

About the Battery

The mobile computer ships with a Li-ion battery manufactured

for Honeywell International Inc.

Before you attempt to use, charge or replace the

battery in the device, carefully read all labels,

markings and product documentation provided in the

box or online at sps.honeywell.com. To learn more

about Battery Maintenance for Portable Devices, go

to honeywell.com/PSS-BatteryMaintenance.

Avant d’essayer d’utiliser, de charger ou de remplacer

la batterie de l’appareil, lisez attentivement toutes les

étiquettes, marquages et documentation du produit

fournis dans la boîte ou en ligne à sps.honeywell.com.

Pour en savoir plus sur l’Entretien de Batteries pour

Appareils Portables, consultez-le

honeywell.com/PSS-BatteryMaintenance.

We recommend use of Honeywell Li-ion battery

packs. Use of any non-Honeywell battery may result

in damage not covered by the warranty.

Nous recommandons l’utilisation de batteries Li-ion

de la marque Honeywell. L’utilisation d’une batterie

d’un autre fabricant est susceptible de provoquer des

dommages non couverts par la garantie.

Ensure all components are dry prior to placing the

battery in the computer. Mating wet components

may cause damage not covered by the warranty.

Assurez-vous que tous les composants sont secs avant

d’insérer la batterie dans l’ordinateur. L’insertion de

composants humides risque de provoquer des

dommages non couverts par la garantie.

CT40 Models

CT40XP Models

Model Configuration

x = configuration

variations

Battery P/N Power

CT40-xxx-xxxxx0x 318-005-011 3.85 VDC, 15.5 watt-hour

CT40-xxx-xxxxxHx 318-055-017

318-055-H67

3.85 VDC, 15.5 watt-hour

CT40-LON-xxxxxAx 318-055-015

318-055-067

3.85 VDC, 15.5 watt-hour

CT40-xxx-xxxxxBx 318-055-015

318-055-067

3.85 VDC, 15.5 watt-hour

CT40-xxx-xxxxxDx 318-055-D67 3.85 VDC, 15.5 watt-hour

Configuration number (CN) is located on the label in the battery well of

the mobile computer.

Model Configuration Battery P/N Power

CT40P-xxx-xxxxxHx 318-055-H67 3.85 VDC, 15.5 watt-hour

CT40P-xxx-xxxxxAx 318-055-067 3.85 VDC, 15.5 watt-hour

CT40P-xxx-xxxxxBx 318-055-067 3.85 VDC, 15.5 watt-hour

CT40P-xxx-xxxxxDx 318-055-D67 3.85 VDC, 15.5 watt-hour

Configuration number (CN) is located on the label in the battery well of

the mobile computer.

Install Battery (Model CT40-xxx-xxxxx0x)

Install Battery (Models CT40-LON-xxxxxAx,

CT40-xxx-xxxxxBx, CT40-xxx-xxxxxHx,

and all CT40XP)

Install the Hand Strap

3 4

1 2

Charge the Mobile Computer

The mobile computer ships with a partially charged battery.

Charge the battery with a CT40 series charging device for a

minimum of 4 hours. Using the computer while charging the

battery increases the time required to reach a full charge.

CT40 series mobile computers are designed for use with the

following CT40 charging accessories: HomeBase, Ethernet

HomeBase, ChargeBase, NetBase, Quad Battery Charger,

Vehicle Power Adapter, Vehicle Dock, and USB Adapter.

We recommend the use of Honeywell accessories and

power adapters. Use of any non-Honeywell

accessories or power adapters may cause damage not

covered by the warranty.

Nous recommandons d’utiliser des accessoires et des

adaptateurs secteur de marque Honeywell.

L’utilisation de tout accessoire ou adaptateur secteur

d’une autre marque est susceptible de provoquer des

dommages non couverts par la garantie.

Ensure all components are dry prior to mating the

computers and batteries with peripheral devices.

Mating wet components may cause damage not

covered by the warranty.

Assurez-vous que tous les composants sont secs

avant de raccorder les ordinateurs et les batteries à

des périphériques. L’insertion de composants

humides risque de provoquer des dommages non

couverts par la garantie.

Turn Power On/Off

The first time you power on the computer, a Welcome screen

appears. You can either scan a configuration barcode or use the

Wizard to manually set up the computer. Once setup is

complete, the Welcome screen no longer appears on startup

and Provisioning Mode is automatically turned off (disabled).

To turn the computer on:

•Press and hold the Power button for approximately 3 seconds,

and then release.

To turn the computer off:

1. Press and hold the Power button until the options menu

appears.

2. Touch Power Off.

Battery Replacement

Before removing the battery, always do one of the following:

• Power off the computer.

• Place the unit in Swap Battery mode (feature availability is

model dependent).

Swap Battery Mode

Swap Battery mode places the computer in a low power state so

that the battery can be removed for a short time. This feature is

not available on all models.

To activate Swap Battery mode:

1. Press and hold the Power button until the options menu

appears.

2. Touch Swap Battery and follow the on-screen instructions.

3. Once you replace the battery, press the Power button.

Screen Timeout

Screen timeout automatically turns the touch panel display off

and locks the computer to save battery power when the

computer is inactive for a programmed period of time.

1. Press and release the Power button to wake the computer.

2. Drag the toward the top of the display to unlock the

computer.

Adjust the Screen Timeout

To adjust the amount of time before the display sleeps after

inactivity:

1. Swipe up on the touch screen.

2. Select Settings > Display > Screen Timeout.

3. Select the amount of time before the display goes to sleep.

4. Touch to return to the Home screen.

About the Home Screen

To learn how to customize the Home screen, see the user guide.

Notification /

Status Bar

Search Bar

Home Screen Panel

Favorites Tray

Navigation Buttons

Navigation and Function Buttons

For button locations, see Mobile Computer Features on page 2.

To learn more about how to re-map a button, see the user guide.

Button Description

Back Return to the previous screen.

Home Return to the Home screen.

Recent Apps View and switch between recently

used apps.

Scan Touch the front (on-screen) Scan

button to trigger the scanner.

Volume Press the top of the button to raise

the speaker volume.

Press the bottom of button to

lower the speaker volume.

Scan Press left or right Scan button to

trigger the scanner.

Power See page 14.

Push-to-Talk Push-to-Talk button is model

dependent.

About Provisioning Mode

After completing the out-of-box set up process, Provisioning

Mode is automatically turned off. Scanning a barcode to install

applications, certificates, configuration files, and licenses on

the computer is restricted unless you enable Provisioning Mode

in the Settings app. To learn more, see the user guide.

Scan a Barcode with the Scan Demo

For optimum performance, avoid reflections by scanning the

barcode at a slight angle.

1. Swipe up on the screen.

2. Select Demos > Scan

Demo.

3. Point the computer at

the barcode.

4. Touch Scan on the

screen or press and

hold any Scan button.

Center the aiming beam

over the barcode.

The decode results appear on the screen.

Note: In the Scan Demo app, not all barcode symbologies are enabled by

default. If a barcode does not scan, the correct symbology may not

be enabled. To learn how to modify the default app settings, see

the user guide.

Sync Data

To move files between your CT40 and a computer:

1. Connect the CT40 to your computer using a USB charge/

communication accessory.

2. On the CT40, swipe down from the top of the screen to see

the notifications panel.

3. Touch the Android System notification twice to open the

options menu.

4. Select either File Transfer or PTP.

5. Open the file browser on your computer.

6. Browse to the CT40. You can now copy, delete, and move

files or folders between your computer and CT40 as you

would with any other storage drive (e.g., cut and paste or

drag and drop).

Note: When Provisioning Mode is turned off, some folders are hidden

from view in the file browser.

Restart the Mobile Computer

You may need to restart the mobile computer to correct

conditions where an application stops responding to the system

or the computer seems to be locked up.

1. Press and hold the Power button until the options menu

appears.

2. Select Power > Restart.

To restart the computer if the touch panel display is

unresponsive:

•Press and hold the Power button for approximately 8 seconds

until the computer restarts.

Note: To learn about advanced reset options, see the user guide.

Support

To search our knowledge base for a solution or to log in to the

Technical Support portal and report a problem, go to

honeywell.com/PSStechnicalsupport.

Documentation

Product documentation is available at sps.honeywell.com.

Limited Warranty

For warranty information, go to sps.honeywell.com and then

select Support > Warranties.

Patents

For patent information, see www.hsmpats.com.

La page charge ...

Honeywell CT40 XP Mode d'emploi

Marque: Honeywell

Modèle: CT40 XP

Catégorie: Les smartphones

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Honeywell CT40 XP User guide

Honeywell CT40 XP Mode d'emploi

Honeywell CT40 XP Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents