MAAX 103412-300-502 Utile back wall 60 in. Guide d'installation

CORNER SHOWER INSTALLATION (2 WALLS)

INSTALLATION DOUCHE EN COIN (2 MURS)

INSTALACIÓN DE DUCHA EN ESQUINA (2 MUROS)

Serial numbers • Numéros de série • Números de serie

Voir Vidéo d'installation - Balayer

QR code avec un dispositif mobile

View Installation Video - Scan

QR code with a mobile device

INSTALLATION INSTRUCTIONS

GUIDE D’INSTALLATION

GUÍA DE INSTALACIÓN

Read all instructions carefully before proceeding.

SAVE THIS GUIDE FOR FUTURE REFERENCE.

Lire toutes les instructions attentivement avant de

commencer l’installation.

CONSERVER POUR UN USAGE ULTÉRIEUR.

Leer detenidamente todas las instrucciones antes de

comenzar la instalación

CONSERVAR ESTE MANUAL COMO REFERENCIA.

A two person installation is required.

Une installation par deux

personnes est requise.

Se recomienda realizar la

instalación entre dos personas

HARDWARE INCLUDED

IN BOXES

QUINCAILLERIE INCLUSE

DANS LES BOÎTES

ACCESORIOS INCLUIDOS

EN LAS CAJAS

OPEN ALL BOXES

BEFORE YOU START

OUVREZ TOUTES LES

BOÎTES AVANT DE

COMMENCER

ABRIR TODAS LAS CAJAS

ANTES DE EMPEZAR

IMPORTANT • Record the serial numbers

IMPORTANT • Noter les numéros de série

IMPORTANTE • Registre el número de serie

Tabla de contenido: Página

Herramientas y materiales.............................................................................................................................. 3

Piezas y componentes....................................................................................................................................4

1. Construcción de la estructura..................................................................................................................... 40

2. Instalación de la base................................................................................................................................. 41

2. Instalación de la base (Olympia)................................................................................................................ 42

2. Instalación de la base (B3)......................................................................................................................... 43

2. Instalación de la base (Distinct / Zone square)........................................................................................... 44

3. Instalación del sistema Ulok sobre los muros............................................................................................ 47

4. Instalación temporal del muro posterior..................................................................................................... 48

5. Instalación temporal de los muros laterales............................................................................................... 49

6. Instalación nal del muro posterior............................................................................................................. 51

7. Instalación nal de los muros laterales....................................................................................................... 52

8. Marcado y perforación de agujeros para la repisa..................................................................................... 53

9. Silicona........................................................................................................................................................53

10. Instalación de la repisa..............................................................................................................................54

11. Acabado del muro..................................................................................................................................... 55

12. Consejos de mantenimiento..................................................................................................................... 56

13. Garantía.................................................................................................................................................... 60

Para las etapas en ESPAÑOL ir a la pagina 40

Table of contents: Page

Tools and supplies.......................................................................................................................................... 3

Parts and components.................................................................................................................................... 4

1. Building the structure.................................................................................................................................. 6

2. Installing the base....................................................................................................................................... 7

2. Installing the base (Olympia)...................................................................................................................... 8

2. Installing the base (B3)............................................................................................................................... 9

2. Installing the base (Distinct / Zone square)................................................................................................ 10

3. Installing Ulok system on the walls............................................................................................................. 13

4. Temporary installation of back wall............................................................................................................. 14

5. Temporary installation of side wall.............................................................................................................. 15

6. Final installation of back wall...................................................................................................................... 17

7. Final installation of side wall....................................................................................................................... 18

8. Marking and drilling the glass shelf holes................................................................................................... 19

9. Silicone........................................................................................................................................................19

10. Glass shelf installation...............................................................................................................................20

11. Wall nish.................................................................................................................................................. 21

12. Maintenance tips....................................................................................................................................... 22

13. Warranty.................................................................................................................................................... 60

Table de matières: Page

Outils et materiaux.......................................................................................................................................... 3

Pièces et composantes...................................................................................................................................4

1. Construction de la structure........................................................................................................................ 23

2. Installation de la base................................................................................................................................. 24

2. Installation de la base (Olympia)................................................................................................................ 25

2. Installation de la base (B3)......................................................................................................................... 26

2. Installation de la base (Distinct / Zone square)........................................................................................... 27

3. Installation du système Ulok sur les murs.................................................................................................. 30

4. Installation temporaire du mur arrière......................................................................................................... 31

5. Installation temporaire du mur de côté....................................................................................................... 32

6. Installation nale du mur arrière................................................................................................................. 34

7. Installation nale du mur de côté................................................................................................................ 35

8. Marquage et perçage des trous pour la tablette......................................................................................... 36

9. Silicone........................................................................................................................................................36

10. Installation de la tablette............................................................................................................................37

11. Finition du mur........................................................................................................................................... 38

12. Conseils d'entretien.................................................................................................................................. 39

13. Garantie.................................................................................................................................................... 60

For installation steps in ENGLISH go to page 6

Pour les étapes d'installation en FRANÇAIS aller à la page 23

3

Hole saw

Scie-cloche

Sierra de

perforación

Screwdriver

Tournevis

Destornillador

24" level min.

Niveau de 24po. min.

Nivel de 24" min.

Pencil

Crayon

Lápiz

Measuring tape

Ruban à mesurer

Cinta métrica

18" square min.

Équerre de 18po. min.

Escuadra de 18" min.

Utility knife

Couteau à lame

rétractable

Cuchillo multiuso

Safety equipment

Équipement de sécurité

Equipamiento de

seguridad

1/8" drill bits

Mèches de 1/8

Box of #8x1¾"flathead screws

Boîte de vis #8x1¾"

à tête plate

Caja de tornillos #8x1¾"

de cabeza plana

Wood shims

Cales en bois

Cuñas de madera

50

Electric drill

Perçeuse électrique

Taladro eléctrico

TOOLS

REQUIRED

OUTILS

REQUIS

HERRAMIENTAS

NECESARIAS

SUPPLIES

SOLD SEPARATELY

MATÉRIAUX

VENDUS SÉPARÉMENT

MATERIALES

VENDIDOS POR SEPARADO

Clear silicone sealant

Silicone claire

Sellador de silicona

transparente

Self levening cement

Ciment auto-nivelant

Cemento

autonivelante

Shower drain

Drain de douche

Desagüe de ducha

*

* Drain required for the Distinct shower base

* Drain requis pour la base de douche Distinct

* Desagüe requerido para la base de ducha Distinct

Cement

Ciment

Cemento

4

6

1

43

2

109

8

5

11

7

# Part Nom de la pièce Pieza Qty/Qté Code

5 Glass shelf Tablette en verre Repisa 1

10060011

6 Bracket Support Soporte de repisa 2

7 #10 x 2’’ screws Vis #10 x 2’’ Tornillos #10 x 1½’’ (repisa) 2

8 Plastic washer Rondelle en plastique Arandela en plástico para repisa 2

9 Support cap Capuchon Tapa de la jación de repisa 2

10 #10 x ½ screws Vis #10 x ½ Tornillos #10 x ½ (para repisa) 2

11 Allen key Clé Allen Llave allen 1

12 Template Gabarit Plantilla de perforación 1

# Part Nom de la pièce Pieza Qt Code

13 Base Base Base 1 *

13a

Drain cover (with

Distinct base only)

Couvercle du drain lineaire (inclus

avec la base Distinct seulement)

Cubierta del desagüe (incluido

con la base Distinct únicamente)

1 10037090

14 Back wall Mur arrière Muro posterior 1 *

15 Side wall Mur de côté Muro lateral 1 *

16

Drain (included with Zone square

and B3Square base only)

Drain (inclus avec la base Zone

square et B3Square seulement)

Desagüe (incluido con la base Zone

square y B3Square únicamente )

1 10028619

PARTS INCLUDED IN PARTS PACK | PIÈCES COMPRISES DANS L'EMBALLAGE DES PIÈCES

| PIEZAS INCLUIDAS EN PAQUETE DE PIEZAS

PARTS INCLUDED IN SHELF PACK | PIÈCES COMPRISES DANS LA BOÎTE DE LA TABLETTE

| PIEZAS INCLUIDAS EN LA CAJA DE LA REPISA

12

Inside the sidewall box

À l'intérieur de la boîte

du mur de côté

En el interior de la caja

del muro lateral

Inside the backwall box

À l'intérieur de la boîte

du mur arrière

En el interior de la caja

del muro posterior

www.maax.com

10060303 – ULOK Skin pack for Utile - 1 junction

3

1

2

4

1

2

BACK WALL

MUR ARRIÈRE

MURO POSTERIOR

INSIDE VIEW

VUE INTÉRIEURE

VISTA INTERIOR

SIDE WALL

MUR DE CÔTÉ

MURO LATERAL

3

4

INSIDE VIEW

VUE INTÉRIEURE

VISTA INTERIOR

by/par

MAAX

* Extra parts are included in this pack in case of loss or damage

* Des pièces supplémentaires sont incluses en cas de perte ou bris

* Piezas extras están incluidas en este empaque en caso de perdida o daño

# Part Nom de la pièce Pieza Qty/Qté Code

1 X fastener Fixation en forme de X Sujetador en forma de X 4

10060303

2

#8 x 1¼’’ Screw

(for X fastener)

Vis #8 x 1¼’’ (Pour

xation en X)

Tornillos #8 x 1¼’’

(Para sujetador en X)

4

3 Retraction pin Cheville d'ancrage Pasador de retracción 4

4

#8 x ⅜ Screw (for

retraction pin)

Vis #8 x ⅜ (pour

cheville d'ancrage)

Tornillos #8 x ⅜ (para

pasador de retracción)

4

PARTS PIÈCES PIEZAS

COMPONENTS COMPOSANTES COMPONENTES

5

13

15

14

4

14

3

INSIDE VIEW

VUE INTÉRIEURE

VISTA INTERIOR

5

9

10

8

7

6

1

2

13

INSIDE VIEW

VUE INTÉRIEURE

VISTA INTERIOR

OVERVIEW VUE D'ENSEMBLE

VISTA GENERAL

6

Build a structure based on the dimensions in the chart

below.

IF STRUCTURE IS ALREADY BUILD CHECK THAT

IT RESPECTS THE DIMENSIONS BELOW

Verify the walls are square, plumb and the ooring is

perfectly level.

6"

C

For a worry free installation follow

all instructions and check them off

as you go.

A

B

C

D

6"

A

B

C

D

6"

A

B

C

D

6"

A

B

C

D

Top view of structure

1.1

Check me!

1.2

Check me!

1.3

Check me!

D

Cut out an approximate 6" x 6" opening around

the drain center outlined by measurements C and

D. See image to the right and the chart above. We

recommend that a plumber completes the drain pipe

connection.

1

STEP Building the structure

Before starting make sure to have all

parts and components refer to page 4.

COMPATIBLE BASES No. A B C D

Olympia square 4832 106011

Between

48"- 48 1/4"

33 1/2"

16" 24"

Olympia square 6032 106012

Between

60"- 60 1/4"

16" 8 1/2"

B3 Square 4832 420001-5XX

Between

48"- 48 1/4"

33 1/2" 16"

24"

B3 Round 4832 410001-5XX

B3 Square 4836 420003-5XX

37 1/2" 18"

B3 Round 4836 410003-5XX

B3 Square 6032 420005-5XX

Between

60"- 60 1/4"

33 1/2" 16"

11 3/4"

B3 Round 6032 410005-5XX

B3 Square 6036 420006-5XX

37 1/2" 18"

B3 Round 6036 410006-5XX

Distinct 4832 106350 48" - 48 1/4" 33 1/2" 4 1/2" 24"

Zone Square 4832 106351 48" - 48 1/4" 33 1/2" 16" 24"

Zone Square 6032 106352 - 106353 60" - 60 1/4" 33 1/2" 16" 11 3/4"

View of 48" shower

Respect front and inside corner studs position, others may vary.

Leveling the oor is critical for a properly aligned

installation. Auto leveling cement can be used to level

oor. Be careful not to block the drain hole position.

FINAL VISUAL INSPECTION

Note: Not doing so could void your warranty

After removing the protective lm and prior to

completing the installation, perform a visual

inspection. If defects are visible, INTERRUPT

THE INSTALLATION and communicate with our

customer service: 1-877-438-6229

7

2

STEP Installing the base

B3 / Olympia / Zone Square / Distinct

Apply silicone around the edge of the drain hole in

the base (surface between the top part of the drain

and the base). Assemble as shown.

HAND TIGHTEN ONLY !

VERIFY THE MAAX LOGO ON THE DRAIN COVER

IS FACING THE RIGHT WAY

REMOVE SILICONE EXCESS!

Install the base (13) pushing it completely against the

studs.

Top view

2.1

Check me!

2.2

Check me!

Cardboard

Rubber

13

Top view

Flush

Studs

Flush

Remove the clear plastic lm from around the drain hole

and threshold before applying silicone. Keep the lm on

the base oor as protection untilinstallation is complete.

Drain assembly (included with Zone square and B3Square, required for the Distinct base)

Threshold

Drain position varies according to base model

8

If needed use wooden shims between the studs and

the fastening ange to maintain the position of the

base.

FOR OLYMPIA BASES DO NOT USE SHIMS UNDER

THE BASE TO LEVEL!

DOING SO WILL VOID THE MAAX WARRANTY!

With a 1/8" bit, drill holes in the fastening ange then

secure the base to all the wall studs with #8 x 1¾ "

screws (not included). Only pre-drill the flange not

the studs.

HAND TIGHTEN ONLY !

THE BOTTOM OF ALL HOLES IN THE FLANGE

HAVE TO BE AT LEAST 8MM (3/8") ABOVE THE

BASE THRESHOLD! HOLES MUST BE FILLED WITH

SILICONE BEFORE SCREWING

CUT THE EXCESS PART OF SHIMS

2

STEP Installing the base (cont'd)

Olympia

2.4

Check me!

2.5

Check me!

Ø 1/8"

3/8" (8 mm)

13

Verify that the base is completely level on all sides. Conrm

that the drain pipe is centered in the drain head.

We recommend a plumber to complete the drain pipe

connection.

2.3

Check me!

Leveling the base is critical

for wall alignment

COMPATIBLE BASES No.

Olympia square 4832 106011

Olympia square 6032 106012

Shims and cement

Cales et ciment

Cuñas y cemento

9

If needed use wooden shims between the studs and

the fastening ange to maintain the position of the

base.

FOR B3 BASES YOU MAY USE SHIMS UNDER

THE BASE TO LEVEL (UNDER THE BASE LEGS

IDEALLY)

With a 1/8" bit, drill holes in the fastening ange then

secure the base to all the wall studs with #8 x 1¾ "

screws (not included). Only pre-drill the flange not

the studs.

HAND TIGHTEN ONLY !

THE BOTTOM OF ALL HOLES IN THE FLANGE

HAVE TO BE AT LEAST 8MM (3/8") ABOVE THE

BASE THRESHOLD! HOLES MUST BE FILLED WITH

SILICONE BEFORE SCREWING

CUT THE EXCESS PART OF SHIMS

2

STEP Installing the base (cont'd)

B3

2.4

Check me!

2.5

Check me!

Ø 1/8"

3/8" (8 mm)

13

Lift the base. Place cement or wood shims under all legs to

support the shower base oor. Lower the shower base and

validate leveling and stability of the base on the oor. If needed,

use additional wood shims or cement.

We recommend that a plumber completes the drain pipe

connection.

2.3

Check me!

Leveling the base is critical

for wall alignment

COMPATIBLE BASES No.

B3 Square 4832 420001-5XX

B3 Round 4832 410001-5XX

B3 Square 4836 420003-5XX

B3 Round 4836 410003-5XX

B3 Square 6032 410005-5XX

B3 Round 6032 410005-5XX

B3 Square 6036 410006-5XX

B3 Round 6036 410006-5XX

Shims and

cement under

to level B3

bases

10

Lift the base. Insert wood shims on the oor around the

outline of the base on the previously marked spots to

compensate leveling.

Lower the base and validate leveling and the stability of

the base on the oor. If needed, use additional shims.

2

STEP Installing the base (cont'd)

Distinct / Zone Square

2.4

Check me!

COMPATIBLE BASES No.

Distinct 4832 106350

Zone square 4832 106351

Zone square 6032 106352 - 106353

Leveling the base is critical

for wall alignment

Verify the base leveling. Mark the studs and the oor

where shims will be required to perfectly level the base.

If the base is completely leveled go to step 2.5

2.3

Check me!

13

11

If needed use wood shims between the studs and the

fastening ange to maintain the position of the base.

2

STEP Installing the base (cont'd)

Distinct / Zone Square

2.6

Check me!

Lift the base. Place cement or wood shims under all legs

to support the shower base oor. Lower the shower base

and validate leveling and stability of the base on the

oor. If needed, use additional wood shims or cement.

We recommend that a plumber completes the drain

pipe connection.

2.5

Check me!

13

Distinct Zone Square

Legs

Check the position

of the legs under

the base to position

the shims if they are

necessary

13

12

Insert the drain cover (13a) as shown.

2

STEP Installing the base (cont'd)

Distinct / Zone Square

2.8

Check me!

With a 1/8" drill bit, drill holes in the base ange then

secure the base to all the wall studs with #8 x 1¾"

at-head screws (not included). Pre-drill the flange

only and not the studs.

HAND TIGHTEN ONLY!

THE BOTTOM OF ALL HOLES IN THE FLANGE

MUST BE AT LEAST 8MM (3/8") ABOVE THE BASE

THRESHOLD! HOLES MUST BE FILLED WITH

SILICONE BEFORE SCREWING

CUT THE EXCESS PART OF SHIMS

2.7

Check me!

Distinct 48 drain cover installation

13a

Ø 1/8"

3/8" (8 mm)

Tiling ange

13

3

STEP Installing Ulok system

on the walls

Install three X fasteners (1) on the side of the back wall

(14) that will be assembled with the side wall, in the pre

drilled holes using the screws provided (2).

Quick tip 

14

Back wall

1

14

2

14

This side

down

4

3

The side wall is interchangeable.

For wall to the left, install the pins

on the right side, for wall to the right

install the pins on the left side.

Quick tip 

Side wall

15

Fastening ange

3.1

Check me!

3.2

Check me!

This side down

There is a positioning pin on X

fastener so they can only be

installed one way.

Positioning

Fasten 3 retraction pins per side wall in the pre drilled

holes with the screws provided (4) to the left-hand or right-

hand fastening ange of the side walls (15) depending on

which side the wall will be installed on.

The Ulok system parts are in the

side wall boxes. (1 pack per box)

www.maax.com

10060303 – ULOK Skin pack for Utile - 1 junction

3

1

2

4

1

2

BACK WALL

MUR ARRIÈRE

MURO POSTERIOR

INSIDE VIEW

VUE INTÉRIEURE

VISTA INTERIOR

SIDE WALL

MUR DE CÔTÉ

MURO LATERAL

3

4

INSIDE VIEW

VUE INTÉRIEURE

VISTA INTERIOR

by/par

MAAX

* Extra parts are included in this pack in case of loss or damage

* Des pièces supplémentaires sont incluses en cas de perte ou bris

* Piezas extras están incluidas en este empaque en caso de perdida o daño

14

4

STEP Temporary installation of the back

wall

Quick tip 

Installing the walls temporarily will

ensure proper wall alignment before

permanent installation.

Make sure the wall is plumb and

centered on the base.

With a 1/8" bit, drill holes in the back wall fastening

flange (14) at the top aligned with each stud. Only pre-

drill the flange not the studs. Then, secure the back

wall (14) with one #8 x 1¾" screw (not included) in one

of the pre-drilled holes.

IMPORTANT: HAND TIGHTEN ONLY. TEMPORARY

INSTALLATION.

Quick tip 

Push the bottom of the back wall

with your foot when fastening in

place.

Plumbing the back wall is

critical for alignment of the

side wall

14

Cut view

Base threshold

Back wall

Position and level the back wall (14) by sitting it on the

threshold at the back of the base.

4.1

Check me!

4.2

Check me!

4.3

Check me!

Pull back the protective lm on the walls (14-15) at least

3" away from all edges. Keep the remaining protective

lm on the walls and base.

min.3/16"

max.3/8"

Stud

X fastener

15

Measure the distance between the front face of the back

wall (14) and the center of the faucet. Then measure the

distance from the top of the base threshold to the center

of the faucet.

Quick tip 

Hole saws can be rented at your

local hardware store or any tool

rental location.

Faucet

center

Using those two measurements mark the position of the

faucet hole on the remaining side wall. Measure from the

side and bottom of the side wall.

Repeat this process for all required faucet holes.

5.2

Check me!

5.1

Check me!

5.3

Check me!

Base

threshold

Front cut

view

Back

wall

Top view

5

STEP Temporary installation of the side wall

For safe hole saw usage always

pre-drill a hole and wear safety

glasses when drilling.

Drill a hole from front for the faucets at the previously

marked positions. Pre-drill the hole with the ⅛'' drill bit.

The hole saw size is determined by the faucet type; refer

to the faucet installation manual for hole saw size.

Measure twice, drill once !

Record measures below.

16

Install the side wall (15). Lift the wall approximately 3"

above the threshold of the base, push it completely

against the back wall then lower the side wall into

position.

Quick tip 

With a 1/8" bit, drill holes in the side wall fastening flange

(15) at the top aligned with each stud. Only pre-drill

the flange not the studs. Then, secure the side wall

(15) with one #8 x 1¾" screw (not included) in one of the

pre-drilled holes.

IMPORTANT: HAND TIGHTEN ONLY. TEMPORARY

INSTALLATION.

3

1

Side wall

Back wall

It is critical that all 3 retraction pins

engage with the X fasteners. There

should be no gap between the walls.

Quick tip 

Place a level vertically

on the side wall. If the

wall is not straight,

make sure that the

retraction pins are

properly inserted in

the X fasteners.

5.4

Check me!

5.5

Check me!

15

5

STEP Temporary installation of the

side walls (Cont'd)

Base

Side wall

The side wall should now line up

with the front of the base. If it does

not, remove the walls and shim

the back ange of base.

17

6

STEP Final installation of back wall

Quick tip 

Hold the bottom of the back wall

with your foot when fastening in

place.

13

5

⅜"

Base

Back

wall

14

⅜"

min.3/16"

max.3/8"

Stud

X fastener

It is critical for the side wall

installation for there to be at least

⅛'' and no more than ⅜" between

the stud and the X fastener.

6.1

Check me!

6.3

Check me!

6.4

Check me!

Remove all walls from the structure.

Clean the shower base and apply a bead of silicone on

the threshold at 3/8" from the back fastening flange. Run

the bead of silicone the entire length of the base and 1''

on the side wall will be installed on as well.

6.2

Check me!

Lift and place back wall (14) directly over the silicone wi-

thout sliding. Verify that the back wall (14) is plumb, shim

if needed. Then, secure the back wall to the wall studs at

top with #8 x 1¾" screws (not included) in the previously

drilled holes.

IMPORTANT: HAND TIGHTEN ONLY. DO NOT

OVER-TIGHTEN THE SCREWS.

Apply a bead of silicone on both sides of base (13) thres-

hold at 3/8" from the base side fastening flanges.

Apply silicone on both side of the back wall (14) just

before the wall side radius. The silicone applied on the

base and vertically on the back wall must overlap.

1"

18

Install the side wall (15). Lift the wall approximately

3 inches above the threshold of the base, push it

completely against the back wall then slide the side

wall into position.

WIPE OFF EXCESS SILICONE

3

1

Side wall

Back wall

7

STEP Final installation of side wall

7.1

Check me!

7.2

Check me!

Secure the wall to the wall studs with #8 x 1¾ "

screws (not included) in the previously drilled holes.

Also, secure the wall by the fastening anges on the

side of the wall. Use the pre-dilled holes.

If needed, use shims to keep wall plumb, square

and leveled. (Cut shim excess)

IMPORTANT: HAND TIGHTEN ONLY. DO NOT

OVER-TIGHTEN THE SCREWS.

Base

Side wall

THE SIDE WALL SHOULD LINE UP WITH

THE BASE

Quick tip 

7.3

Check me!

BEFORE CONTINUING,

VALIDATE THAT ALL

THE WALLS ARE LEVEL,

PLUMB AND SQUARE

19

Check me!

Place the template in the corner of the shower where

you want to install your shelf.

Slide the template up until the points on the left and

right-hand side of the template are at the height you

want your shelf.

Use a pencil, marker or wax pencil to mark the spots

where the holes for the shelf will be drilled.

Drill the holes using a 9/64" drill bit.

8

STEP Marking and drilling the

glass shelf holes

Fold here

Drilling positions

?

90°

Quick tip 

Apply masking tape on both sides

of the joint where you will run a

bead of silicone. Apply the silicone,

smooth with a wet nger then

remove the masking tape.

Check me!

Apply a bead of silicone all along the wall to wall

and wall to base joints. For a smooth nish you can

remove the silicone excess with a damp rag or wet

nger.

9

STEP Silicone

All faucets installed on the walls

must be sealed with silicone.

Remove protective lm from walls

20

Apply silicone in the previously drilled holes on the side

and back walls. Apply silicone to the rear of the shelf

brackets (6).

Fasten the brackets in place using the screws (7).

10

STEP Glass shelf installation

7

6

10.1

Check me!

Clean the top rubber part of the brackets with a damp

cloth, then place the glass shelf (5) over the brackets (6).

5

6

Quick tip 

If you can read the MAAX logo, the

shelf is installed on the right side.

10.2

Check me!

When installing the faucet

faceplate or any other

component, be sure to

silicone the outer edge.

La page charge ...

MAAX 103412-300-502 Utile back wall 60 in. Guide d'installation

Ce manuel convient également à

MAAX 103412-300-502 Utile back wall 60 in. Guide d'installation

dans d''autres langues

Documents connexes

Autres documents