GE Profile PSC23NGNWW Le manuel du propriétaire

www.GEAppliances.com
Refrigerators
Profile Side by Side
200D2600P039 49-60342    09-04 JR
La section française commence à la page 46
La sección en español empieza en la página 88
Safety Instructions  . . . . . . . . . . .2–4
Operating Instructions
Automatic Icemaker  . . . . . . . . . . .14
Care and Cleaning . . . . . . . . . .16, 17
Crispers and Pans  . . . . . . . . . . . . .13
CustomCool
™
 . . . . . . . . . . . . . . . .7, 8
Ice and Water Dispenser  . . . . . . . .15
Refrigerator Doors  . . . . . . . . . . . .12
Replacing the Light Bulbs . . . . . . .18
Shelves and Bins  . . . . . . . . . . .10, 11
Temperature Controls . . . . . . . . . . .5
TurboCool
™
 . . . . . . . . . . . . . . . . . . .6
Water Filter  . . . . . . . . . . . . . . . . . . .9
Installation Instructions
Installing the Refrigerator  . . . .28–31
Moving the Refrigerator  . . . . .24–27
Preparing to Install 
the Refrigerator . . . . . . . . . . . . . . .23
Trim Kits and Panels  . . . . . . . .19–22
Water Line Installation  . . . . . .32–34
Troubleshooting Tips . . . . . . .36–38
Normal Operating Sounds  . . . . . .35
Consumer Support
Consumer Support  . . . . .Back Cover
Performance Data Sheet  . . . . . . . .41
Product Registration  . . . . . . . .43, 44
State of California Water 
Treatment Device Certificate . . . . .42
Warranty (Canadian) . . . . . . . . . . .39
Warranty (U.S.)  . . . . . . . . . . . . . . .40
Réfrigérateurs
Profile Côte à Côte
Refrigeradores
Profile Lado a Lado
Models 23, 25, 26, 27 and 29
Write the model and serial numbers here:
Model # __________________________
Serial # __________________________
Find these numbers on a label inside 
the refrigerator compartment at the 
top on the right side.
Owner’s Manual 
and Installation
Manuel d’utilisation 
et d’installation
Manual del propietario 
e instalación

Consumer Support

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

2

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

Use this appliance only for its intended purpose as described in this Owner’s Manual.

SAFETY PRECAUTIONS

When using electrical appliances, basic safety precautions should be followed, including the following:

■

■ This refrigerator must be properly installed

and located in accordance with the Installation

Instructions before it is used.

■

■ Do not allow children to climb, stand or hang

on the shelves in the refrigerator. They could

damage the refrigerator and seriously injure

themselves.

■

■ Do not touch the cold surfaces in the freezer

compartment when hands are damp or wet. Skin

may stick to these extremely cold surfaces.

■

■ Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any

other appliance.

■

■ In refrigerators with automatic icemakers,

avoid contact with the moving parts of the

ejector mechanism, or with the heating element

located on the bottom of the icemaker. Do not

place fingers or hands on the automatic

icemaking mechanism while the refrigerator

is plugged in.

■

■ Keep fingers out of the “pinch point” areas;

clearances between the doors and between

the doors and cabinet are necessarily small.

Be careful closing doors when children are

in the area.

■

■ Unplug the refrigerator before cleaning and

making repairs.

NOTE: We strongly recommend that any servicing be

performed by a qualified individual.

■

■ Setting either or both controls to 0 (off) does not

remove power to the light circuit.

■

■ Do not refreeze frozen foods which have

thawed completely.

■

■ Always clean the CustomCool

™

Tray after thawing

food.

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

GEAppliances.com

PROPER DISPOSAL OF THE REFRIGERATOR

Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are

still dangerous…even if they will sit for “just a few

days.” If you are getting rid of your old refrigerator,

please follow the instructions below to help prevent

accidents.

Before You Throw Away Your Old Refrigerator

or Freezer:

■ Take off the doors.

■ Leave the shelves in place so that children may

not easily climb inside.

Refrigerants

All refrigeration products contain refrigerants,

which under federal law must be removed prior

to product disposal. If you are getting rid of an

old refrigeration product, check with the

company handling the disposal about what

to do.

USE OF EXTENSION CORDS

Because of potential safety hazards under certain conditions, we strongly recommend against the use

of an extension cord.

However, if you must use an extension cord, it is absolutely necessary that it be a UL-listed (in the United

States) or a CSA-listed (in Canada), 3-wire grounding type appliance extension cord having a grounding

type plug and outlet and that the electrical rating of the cord be 15 amperes (minimum) and 120 volts.

DANGER! RISK OF CHILD ENTRAPMENT

3

4

Consumer Support

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

HOW TO CONNECT ELECTRICITY

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For

personal safety, this appliance must be properly grounded.

The power cord of this appliance is equipped

with a 3-prong (grounding) plug which mates

with a standard 3-prong (grounding) wall outlet

to minimize the possibility of electric shock hazard

from this appliance.

Have the wall outlet and circuit checked by a

qualified electrician to make sure the outlet is

properly grounded.

If the outlet is a standard 2-prong outlet, it is your

personal responsibility and obligation to have it

replaced with a properly grounded 3-prong wall

outlet.

The refrigerator should always be plugged into its

own individual electrical outlet which has a voltage

rating that matches the rating plate.

This provides the best performance and also

prevents overloading house wiring circuits which

could cause a fire hazard from overheated wires.

Never unplug your refrigerator by pulling on the

power cord. Always grip plug firmly and pull straight

out from the outlet.

Repair or replace immediately all power cords that

have become frayed or otherwise damaged. Do not

use a cord that shows cracks or abrasion damage

along its length or at either end.

When moving the refrigerator away from the

wall, be careful not to roll over or damage the

power cord.

USE OF ADAPTER PLUGS (Adapter plugs not permitted in Canada)

Because of potential safety hazards under certain conditions, we strongly recommend against

the use of an adapter plug.

However, if you must use an adapter, where local

codes permit, a temporary connection may be made

to a properly grounded 2-prong wall outlet by use

of a UL-listed adapter available at most local

hardware stores.

The larger slot in the adapter must be aligned with

the larger slot in the wall outlet to provide proper

polarity in the connection of the power cord.

When disconnecting the power cord from the

adapter, always hold the adapter in place with one

hand while pulling the power cord plug with the

other hand. If this is not done, the adapter ground

terminal is very likely to break with repeated use.

If the adapter ground terminal breaks, DO NOT

USE the refrigerator until a proper ground has

been established.

Attaching the adapter ground terminal to a wall outlet

cover screw does not ground the appliance unless the

cover screw is metal, and not insulated, and the wall

outlet is grounded through the house wiring. You should

have the circuit checked by a qualified electrician to make

sure the outlet is properly grounded.

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

About the temperature controls. GEAppliances.com

The temperature controls are preset in the factory at 37°F for the

refrigerator compartment and 0°F for the freezer compartment. Allow

24 hours for the temperature to stabilize to the preset recommended

settings.

The temperature controls can display both the SET temperature

as well as the actual temperature in the refrigerator and freezer.

The actual temperature may vary slightly from the SET temperature

based on usage and operating environment.

Setting either or both controls to OFF stops cooling in both the freezer

and refrigerator compartments, but does not shut off electrical power

to the refrigerator.

NOTE: The refrigerator is shipped with protective film covering the

temperature controls. If this film was not removed during installation,

remove it now.

The Performance Air-Flow System is designed to

maximize temperature control in the refrigerator

and freezer compartments. This unique special

feature consists of the Air Tower along the back

wall of the refrigerator and the Air Tunnel on the

bottom portion of the freezer rear wall. Placing food

in front of the louvers on these components will not

affect performance. Although the Air Tower and

the Air Tunnel can be removed, doing so will affect

temperature performance. (For removal

instructions, on-line, 24 hours a day, contact us at

GEAppliances.com or call 800.GE.CARES. In

Canada, contact us at geappliances.ca or call

1.800.361.3400.)

Performance Air Flow System

To change the temperature, press and release the

WARMER or COLDER pad. The SET light will come

on and the display will show the set temperature.

To change the temperature, tap either the

WARMER or COLDER pad until the desired

temperature is displayed. Refrigerator temperatures

can be adjusted between 34°F and 44°F and the

freezer temperatures can be adjusted between

–6°F and +6°F.

Once the desired temperature has been set,

the temperature display will return to the actual

refrigerator and freezer temperatures after 5

seconds. Several adjustments may be required.

Each time you adjust controls, allow 24 hours for the

refrigerator to reach the temperature you have set.

To turn the cooling system off, tap the WARMER pad

for either the refrigerator or the freezer until the

display shows OFF. To turn the unit back on, press the

COLDER pad for either the refrigerator or freezer.

The SET light will illuminate on the side you

selected. Then press the COLDER pad again (on the

side where the SET light is illuminated) and it will

go to the preset points of 0°F for the freezer and

37°F for the refrigerator. Setting either or both

controls to OFF stops cooling in both the freezer

and refrigerator compartments, but does not shut

off electrical power to the refrigerator.

5

6

About TurboCool.

™

How it Works

TurboCool

™

rapidly cools the refrigerator

compartment in order to more quickly

cool foods. Use TurboCool when adding a

large amount of food to the refrigerator

compartment, putting away foods after they

have been sitting out at room temperature

or when putting away warm leftovers. It can

also be used if the refrigerator has been

without power for an extended period.

Once activated, the compressor will turn on

immediately and the fans will cycle on and

off at high speed as needed for eight hours.

The compressor will continue to run until

the refrigerator compartment cools to

approximately 34°F (1°C), then it will cycle

on and off to maintain this setting. After

8 hours, or if TurboCool is pressed again,

the refrigerator compartment will return

to the original setting.

How to Use

Press TurboCool. The refrigerator

temperature display will show TC.

After TurboCool is complete, the refrigerator

compartment will return to the original

setting.

NOTES:

The refrigerator temperature cannot be changed

during TurboCool.

The freezer temperature is not affected during

TurboCool.

When opening the refrigerator door during

TurboCool, the fans will continue to run if they

have cycled on.

Consumer Support

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

About ClimateKeeper2.

™

How it Works

The new ClimateKeeper2

™

is the industry’s

most advanced refrigeration system,

delivering optimum temperature and

humidity performance to keep food fresh

longer and reduce freezer burn, while

maintaining E star-level efficiency.

The new ClimateKeeper2 system features

two evaporators—one for the refrigerator

and one for the freezer.

This provides two separate cooling systems

for the entire unit, and separates the

airflow between the fresh food and freezer

sections during normal cooling operations.*

This ensures that the humidity levels in the

fresh food section are significantly higher

than in a conventional system,** allowing

fresh produce and other unsealed foods to

retain their moisture content and freshness

longer. Moisture sensitive foods such as

fresh fruit, salads, rice, etc., can now be

stored on open shelves without excessive

moisture loss.

The separate airflow system minimizes

the mixing of air between the two

compartments, which reduces odor

transfer, resulting in improved taste of ice.

The ClimateKeeper2 system also reduces

the number of defrosting cycles in the

freezer evaporator, thereby improving the

temperature maintained in the freezer and

reducing freezer burn.

*Freezer air is used in the CustomCool feature.

**Testing shows a higher level of humidity in

the Fresh Food section in ClimateKeeper2

refrigerators versus conventional units.

7

Empty the pan. Place the Chill/Thaw

tray in the pan. Place the items on the

tray and close the pan completely.

Select the ExpressThaw,

™

ExpressChill

™

or SelectTemp

™

pad. The display and

SET light will come on. Tap the pad

until the light appears next to the

desired setting. Use the chart to

determine the best setting to use.

■ To stop a feature before it is

finished, tap that feature’s pad

until no options are selected and

the display is off.

■ During ExpressThaw and

ExpressChill, the display on the

controls will count down the time

in the cycle.

■ After the ExpressThaw cycle is

complete, the pan will reset to the

MEAT setting (32°F) to help preserve

thawed items until they are used.

■ The displayed actual temperature of

the CustomCool pan may vary slightly

from the SET temperature based on

usage and operating environment.

NOTE: For food safety reasons, it is recommended

that foods be wrapped in plastic wrap when using

ExpressThaw. This will help contain meat juices

and improve thawing performance.

About CustomCool

™

. GEAppliances.com

The CustomCool

™

feature is a system of

dampers, a fan, a temperature thermistor

and a heater. Depending on the function

selected, a combination of these will be

used to quickly chill items, thaw items or

hold the pan at a specific temperature.

The pan is tightly sealed to prevent the pan’s

temperature from causing temperature

fluctuations in the rest of the refrigerator.

Some CustomCool models feature a beverage

center. It is designed to store beverages at

colder temperatures. Select the Beverage

Center pad if you like to keep extra-chilled

refreshments on hand.

The controls for this pan are located at the

top of the refrigerator with the temperature

controls.

How to Use

How it Works

ExpressThaw

™

To remove:

Pull the drawer out to the stop position.

Rotate all four swing locks to the unlock

position.

Lift the front of the drawer up and out.

To replace:

Make sure all four swing locks are in the

unlock position.

Place the sides of the drawer into the

drawer supports, making sure the swing

locks fit on the drawer slots.

Lock all four swing locks by rotating

them to the lock position.

How to Remove and Replace the Drawer

ExpressChill

™

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

8

About CustomCool

™

.

CustomCool

™

Chart

NOTE: Results may vary depending on packaging, starting temperature and other food traits.

0.5 Lb. (4 hours)

■ Hamburger Patties (0.5 lb)

■ Individually Wrapped

Filet Mignon (0.5 lb)

1.0 Lb. (6 hours)

■ Chicken Breasts (1.0 lb)

■ Ground Beef (1.0 lb)

■ Steak (1.0 lb)

2.0 Lbs. (10 hours)

■ Chicken Breasts (2.0 lbs)

■ Ground Beef (2.0 lbs)

■ Steak (2.0 lbs)

3.0 Lbs. (12 hours)

■ Chicken Breasts (3.0 lbs)

■ Ground Beef (3.0 lbs)

■ Steak (3.0 lbs)

15 Minutes

■ 1 Beverage Can (12 oz)

■ 2 Small Juice Boxes (6–8 oz each)

30 Minutes

■ 2 to 6 Beverage Cans (12 oz each)

■ 2 Plastic 20 oz Bottles of Beverage

■ 4 to 6 Small Juice Boxes

(6–8 oz each)

■ 3 Foil Juice Packets

■ Wine (750 ml bottle)

45 Minutes

■ 2 Liter of Beverage

■ 1/2 Gallon of Juice

■ Gelatin–1 package

Citrus Setting (43°F)

■ Oranges, Lemons, Limes,

Pineapple, Cantaloupe

■ Beans, Cucumbers, Tomatoes,

Peppers, Eggplant, Squash

Produce Setting (35°F)

■ Strawberries, Raspberries, Kiwifruit,

Pears, Cherries, Blackberries,

Grapes, Plums, Nectarines, Apples

■ Asparagus, Broccoli, Corn,

Mushrooms, Spinach, Cauliflower,

Kale, Green Onion, Beets, Onions

Meat Setting (32°F)

■ Raw Meat, Fish and Poultry

Consumer Support

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

Select the Beverage Center pad. The set

light will come on and the feature will

operate as required.

To turn off the feature, press Beverage

Center pad and set light will turn off.

NOTE: Unless turned off as above, feature will

remain active for six months. Press the Beverage

Center pad to restart.

How to Use

To remove:

Remove dairy bin first. Holding the

bottom of the dairy bin, lift the front

straight up, then lift up and out.

Holding left and right side of beverage

center, lift straight up and out.

Leave adapter in place.

To replace:

Engage backside of beverage center in

molded supports on adapter. Then

push down on the sides of the beverage

center. The beverage center will lock

into place.

Replace dairy bin.

How to Remove and Replace the Beverage Center

Dairy Bin

Adapter

Beverage

Center

About the water filter. (on some models) GEAppliances.com

9

Water Filter Cartridge

The water filter cartridge is located in the

back upper right corner of the refrigerator

compartment.

When to Replace the Filter

There is a replacement indicator light for

the water filter cartridge on the dispenser.

This light will turn orange to tell you that

you need to replace the filter soon.

The filter cartridge should be replaced

when the replacement indicator light turns

red or if the flow of water to the dispenser

or icemaker decreases.

Installing the Filter Cartridge

If you are replacing the cartridge, first

remove the old one by slowly turning

it to the left. Do not pull down on the

cartridge. A small amount of water may

drip down.

Fill the replacement cartridge with

water from the tap to allow for better

flow from the dispenser immediately

after installation.

Lining up the arrow on the cartridge

and the cartridge holder, place the

top of the new cartridge up inside

the holder. Do not push it up into

the holder.

Slowly turn it to the right until the filter

cartridge stops. DO NOT OVERTIGHTEN.

As you turn the cartridge, it will

automatically raise itself into position.

Cartridge will rotate about 1/4 turn.

Run water from the dispenser for

3 minutes (about 1

1

⁄2 gallons) to clear

the system and prevent sputtering.

Press and hold the RESET WATER FILTER

pad on the dispenser for 3 seconds.

NOTE: A newly-installed water filter cartridge may

cause water to spurt from the dispenser.

Filter Bypass Plug

You must use the filter bypass plug

when a replacement filter cartridge is not

available. The dispenser and the icemaker

will not operate without the filter or filter

bypass plug.

Replacement Filters:

To order additional filter cartridges

in the United States, visit our Website,

GEAppliances.com, or call

GE Parts and Accessories, 800.626.2002.

GWF

Suggested Retail $34.95 USD

Customers in Canada should consult

the yellow pages for the nearest Camco

Service Center.

Place the top of the cartridge up

inside the cartridge holder and

slowly turn it to the right.

Filter Bypass Plug

Cartridge

Holder

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

Consumer Support

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

10

About the shelves and bins.

Refrigerator Door Bins and Freezer Door Tilt-Out Bins

Large Bins

The larger refrigerator door bins and

freezer tilt-out door bins are adjustable.

To remove: Lift the front of the bin straight

up, then lift up and out.

To replace or relocate: Engage the back side

of the bin in the molded supports on the

door. Then push down on the front of the

bin. Bin will lock in place.

Small Bins

To remove: Lift the front of the bin straight

up then out.

To replace: Position the bin above the

rectangular molded supports on the door.

Then slide the bin down onto the support

to lock it in place.

The snugger helps prevent tipping, spilling

or sliding of small items stored on the door

shelf. Place a finger on either side of the

snugger near the rear and move it back

and forth to fit your needs.

Not all features are on all models.

Refrigerator bin

Freezer tilt-out bin

Snugger

QuickSpace

™

Shelf

This shelf splits in half and slides under

itself for storage of tall items on the shelf

below.

This shelf can be removed and replaced

or relocated just like Slide-Out Spillproof

Shelves.

On some models, this shelf cannot be used

in the lowest position.

Slide-Out Spillproof Shelf

The slide-out spillproof shelf allows you

to reach items stored behind others. The

special edges are designed to help prevent

spills from dripping to lower shelves.

To remove:

Slide the shelf out until it reaches the stop,

then press down on the tab and slide the

shelf straight out.

To replace or relocate:

Line the shelf up with the supports and

slide it into place. The shelf can be

repositioned when the door is at 90° or

more. To reposition the shelf, slide the shelf

past the stops and angle downward. Slide

shelf down to the desired position, line up

with the supports and slide into place.

Make sure you push the shelves all the way back

in before you close the door.

Press tab and pull shelf forward

to remove

Top freezer bin

Do not block

CAUTION:

Be careful when

placing items in the

top bin. Make sure

that items do not

block or fall into

the ice chute.

Top freezer bin (on some models)

Do not block

CAUTION:

Part must be in

place as shown

for proper ice

dispensing. Food

cannot be stored

in this location.

GEAppliances.com

Not all features are on all models.

Slide-Out Freezer Shelves

To remove, slide out to the stop position,

lift the front past the stop position and

slide out.

Make sure you push the shelves all the way back

in before you close the door.

Freezer Baskets

To remove, push the basket all the way to the

back of the freezer. Lift up until the back

pins are disengaged. Lift the entire basket

up and pull out.

Make sure you push the baskets all the way back

in before you close the door.

Fixed Freezer Shelves

There are two types of fixed

freezer shelves.

To remove this type of shelf:

Lift the shelf up at the left side.

Bring the shelf out.

To remove this type of shelf:

Lift up the left side of the shelf and

slide it left into the center of the shelf

supports.

Rotate the right side of the shelf up

and out of the shelf supports.

NOTE FOR DISPENSER MODELS: In order to take

full advantage of the tilt-out ice bin, only store items

on the shelf below the ice bin that are no taller than

the lowest point on the bin.

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

Door Wine/Beverage Rack (on some models)

This rack holds up to 5 cans, one bottle of

wine or one 2-liter bottle of soda.

The rack hangs from the sides of the

dairy bin.

To remove:

Empty the wine/beverage rack.

Holding the bottom of the dairy bin,

lift the front straight up, then lift up

and out.

To detach the rack from the dairy bin,

pull the rack’s side wires out of the

holes on each side of the dairy bin.

To replace:

Reattach the rack to the sides

of the bin.

Engage the back side of the bin in

the molded supports on the door.

Then push down on the front of the

bin. The bin will lock into place.

11

Consumer Support

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

12

About the refrigerator doors.

Refrigerator Doors

The refrigerator doors may feel different

than the ones you are used to. The special

door opening/closing feature makes sure

the doors close all the way and are securely

sealed.

When opening and closing the door you

will notice a stop position. If the door is

opened past this stop point, the door will

remain open to allow you to load and

unload food more easily. When the door

is only partially open, it will automatically

close.

The resistance you feel at the stop

position will be reduced as the door

is loaded with food.

When the door is only partially open,

it will automatically close.

Beyond this stop the door will stay open.

Door Alignment

If doors are uneven, adjust the refrigerator

door.

Using a 7/16″ wrench, turn the door

adjusting screw to the right to raise the

door, to the left to lower it. (A nylon

plug, imbedded in the threads of the

pin, prevents the pin from turning

unless a wrench is used.)

After one or two turns of the wrench,

open and close the refrigerator door

and check the alignment at the top of

the doors.

7/16″ Wrench

Raise

About the crispers and pans. GEAppliances.com

13

About crisper removal.

Not all features are on all models.

Crisper Removal

Crispers can easily be removed by pulling

the drawer straight out and lifting the

drawer up and over the stop location.

If the door prevents you from taking out

the drawers, first try to remove the door

bins. If this does not offer enough

clearance, the refrigerator will need to

be rolled forward until the door opens

enough to slide the drawers out. In some

cases, when you roll the refrigerator out,

you will need to move the refrigerator

to the left or right as you roll it out.

Not all features are on all models.

Fruit and Vegetable Crispers

Excess water that may accumulate in the

bottom of the drawers should be wiped dry.

On some models, the bottom drawer has

full extension slides that allow full access

to the drawer.

Adjustable Humidity Crispers

Slide the control all the way to the HI setting

to provide high humidity recommended for

most vegetables.

Slide the control all the way to the LO

setting to provide lower humidity levels

recommended for most fruits.

HI LO

Convertible Deli Pan

The convertible deli pan has its own cold

air duct to allow a stream of cold air from

the freezer compartment or fresh food

compartment to flow to the pan.

The variable temperature control regulates

the air flow from the Climate Keeper.

Set the control to the coldest setting to

store fresh meats.

Set the control to cold to convert the pan

to normal refrigerator temperature and

provide extra vegetable storage space. The

cold air duct is turned off. Variable settings

between these extremes can be selected.

C

O

L

D

C

O

L

D

E

S

T

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

About the automatic icemaker.

Consumer Support

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

14

Automatic Icemaker

The icemaker will produce seven cubes

per cycle—approximately 100–130 cubes

in a 24-hour period, depending on freezer

compartment temperature, room

temperature, number of door openings

and other use conditions.

If the refrigerator is operated before the

water connection is made to the icemaker,

set the power switch in the O (off) position.

When the refrigerator has been connected

to the water supply, set the power switch to

the l (on) position.

The icemaker will fill with water when it

cools to 15°F (–10°C). A newly installed

refrigerator may take 12 to 24 hours to begin

making ice cubes.

You will hear a buzzing sound each time

the icemaker fills with water.

Throw away the first few batches of ice to

allow the water line to clear.

Be sure nothing interferes with the sweep

of the feeler arm.

When the bin fills to the level of the feeler

arm, the icemaker will stop producing

ice. It is normal for several cubes to be

joined together.

If ice is not used frequently, old ice cubes

will become cloudy, taste stale and shrink.

Special note about dispenser models:

■ Dispenser models have a tilt-out ice bin.

The bin can be tilted out as shown in the

illustrations, and it will hold itself up

while you take ice out or turn the

icemaker power switch on and off. Be

sure to put the bin back in place before

closing the door.

■ To restore your ice level from an empty

bucket stage, the following steps are

recommended:

12 hours after the first batch of ice

has fallen into the bin, dispense

3 to 4 cubes.

After an additional 6 hours, dispense

3 to 4 cubes again.

These steps will restore your ice level

in the shortest amount of time.

NOTE: In homes with lower-than-average water

pressure, you may hear the icemaker cycle multiple

times when making one batch of ice.

A newly installed refrigerator may take 12 to 24 hours to begin making ice.

Lift the bin, then pull it

forward until the bin stops.

Removing Ice Bin (dispenser models)

CAUTION: The ice bin is heavy when full.

Set the power switch to the O (off) position

before removing the bin.

When replacing the bin, be sure to press it

firmly into place. If it does not go all the

way back, remove it and rotate the drive

mechanism 1/4 turn. Then push the bin

back again.

Icemaker

Feeler Arm

Power

Switch

Green

Power Light

Lower the bin to access ice

or reach the power switch.

NOTE: In order to take full advantage

of the tilt-out ice bin, only store items

on the shelf below the ice bin that

are no taller than the lowest point

on the bin.

On dispenser models,

to access ice or reach

the power switch:

Lift the bin, then pull it

forward until the bin stops.

Lift and pull forward again

to remove the bin.

Rotate

Drive

Mechanism

Dispenser Models only

Important Facts About Your Dispenser

■ Do not add ice from trays or bags to

the storage drawer. It may not crush or

dispense well.

■ Avoid overfilling glass with ice and use of

narrow glasses. Backed-up ice can jam the

chute or cause the door in the chute to

freeze shut. If ice is blocking the chute,

poke it through with a wooden spoon.

■ Beverages and foods should not be

quick-chilled in the ice storage drawer.

Cans, bottles or food packages in the

storage drawer may cause the icemaker

or auger to jam.

■ To keep dispensed ice from missing

the glass, put the glass close to, but not

touching, the dispenser opening.

■ Some crushed ice may be dispensed

even though you selected CUBED ICE.

This happens occasionally when a few

cubes accidentally get directed to

the crusher.

■ After crushed ice is dispensed, some

water may drip from the chute.

■ Sometimes a small mound of snow will

form on the door in the ice chute. This

condition is normal and usually occurs

when you have dispensed crushed ice

repeatedly. The snow will eventually

evaporate.

15

About the ice and water dispenser. (on some models) GEAppliances.com

To Use the Dispenser

Select CUBED ICE , CRUSHED ICE

or WATER .

Press the glass gently against the top of

the dispenser cradle.

The spill shelf is not self-draining.

To reduce water spotting, the shelf and

its grille should be cleaned regularly.

If no water is dispensed when the refrigerator is

first installed, there may be air in the water line

system. Press the dispenser arm for at least two

minutes to remove trapped air from the water

line and to fill the water system. To flush out

impurities in the water line, throw away the first

six glassfuls of water.

CAUTION: Never put fingers or any other

objects into the ice crusher discharge opening.

Locking the Dispenser

Press the LOCK CONTROL

pad for 3 seconds to

lock the dispenser and

control panel. To

unlock, press and

hold the pad again

for 3 seconds.

Dispenser Light

This pad turns the night

light in the dispenser

on and off. The light

also comes on when

the dispenser cradle is

pressed. On some

models, if this light

burns out, it should be

replaced with a 6 watt

12V maximum bulb.

Quick Ice

When you need ice

in a hurry, press this

pad to speed up ice

production. This will

increase ice production

for the following

48 hours or until you

press the pad again.

Door Alarm

To set the alarm, press

this pad until the

indicator light comes

on. This alarm will

sound if either door is

open for more than

3 minutes. The light

goes out and the

beeping stops when

you close the door.

Spill Shelf

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

Consumer Support

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

16

Cleaning the Outside

The dispenser drip area, beneath the grille,

should be wiped dry. Water left in this area

may leave deposits. Remove the deposits by

adding undiluted vinegar to the well. Soak

until the deposits disappear or become

loose enough to rinse away.

The dispenser cradle. Before cleaning, lock

the dispenser by pressing and holding the

LOCK CONTROL pad for 3 seconds. Clean

with warm water and baking soda

solution—about a tablespoon (15 ml) of

baking soda to a quart (1 liter) of water.

Rinse thoroughly and wipe dry.

The door handles and trim. Clean with

a cloth dampened with soapy water.

Dry with a soft cloth.

The stainless steel panels and door handles

(on some models) can be cleaned with

a commercially available stainless steel

cleaner. A spray-on stainless steel cleaner

works best.

Do not use appliance wax or polish

on the stainless steel.

Keep the outside clean. Wipe with a clean

cloth lightly dampened with kitchen

appliance wax or mild liquid dish detergent.

Dry and polish with a clean, soft cloth.

Do not wipe the refrigerator with a soiled dish

cloth or wet towel. These may leave a residue

that can erode the paint. Do not use scouring

pads, powdered cleaners, bleach or cleaners

containing bleach because these products can

scratch and weaken the paint finish.

Cleaning the Inside

To help prevent odors, leave an open box of

baking soda in the fresh food and freezer

compartments.

Unplug the refrigerator before cleaning. If this

is not practical, wring excess moisture out

of sponge or cloth when cleaning around

switches, lights or controls.

Use warm water and baking soda solution—

about a tablespoon (15 ml) of baking soda

to a quart (1 liter) of water. This both

cleans and neutralizes odors. Rinse and

wipe dry.

Use of any cleaning solution other than that

which is recommended, especially those that

contain petroleum distillates, can crack or

damage the interior of the refrigerator.

Avoid cleaning cold glass shelves with hot water

because the extreme temperature difference

may cause them to break. Handle glass shelves

carefully. Bumping tempered glass can cause

it to shatter.

Do not wash any plastic refrigerator parts

in the dishwasher.

The chill/thaw tray is dishwasher safe.

Dispenser drip area.

Care and cleaning of the refrigerator.

17

For long vacations or absences, remove

food and unplug the refrigerator. Clean the

interior with a baking soda solution of one

tablespoon (15 ml) of baking soda to one

quart (1 liter) of water. Leave the doors

open.

Set the icemaker power switch to the O (off)

position and shut off the water supply to

the refrigerator.

If the temperature can drop below freezing,

have a qualified servicer drain the water

supply system to prevent serious property

damage due to flooding.

GEAppliances.com

Behind the Refrigerator

Be careful when moving the refrigerator

away from the wall. All types of floor

coverings can be damaged, particularly

cushioned coverings and those with

embossed surfaces.

Pull the refrigerator straight out and return

it to position by pushing it straight in.

Moving the refrigerator in a side direction

may result in damage to the floor covering

or refrigerator.

When pushing the refrigerator back, make sure

you don’t roll over the power cord or icemaker

supply line.

Preparing for Vacation

Preparing to Move

Secure all loose items such as shelves and

drawers by taping them securely in place

to prevent damage.

When using a hand truck to move the

refrigerator, do not rest the front or back

of the refrigerator against the hand truck.

This could damage the refrigerator. Handle

only from the sides of the refrigerator.

Be sure the refrigerator stays in an upright

position during moving.

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

Consumer Support

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

18

Replacing the light bulbs.

Setting the controls to OFF does not remove power to the light circuit.

Refrigerator Compartment—Upper Light

Unplug the refrigerator.

The bulbs are located at the top of the

compartment, inside the light shield.

On some models, a screw at the front of

the light shield will have to be removed.

To remove the light shield, on some

models, press in on the tabs on the

sides of the shield and slide forward

and out. On other models, just slide

forward and out.

After replacing the bulb with an

appliance bulb of the same or lower

wattage, replace the light shield and

screws (on some models). When

replacing the light shield, make sure

that the tabs at the back of the shield

fit into the slots at the back of the light

shield housing.

Plug the refrigerator back in.

Refrigerator Compartment—Lower Light

This light is located above the top drawer.

Unplug the refrigerator.

Remove the convertible meat drawer

control knob by pulling straight out.

Lift the light shield up and pull it out.

After replacing the bulb with an

appliance bulb of the same or lower

wattage, replace the shield and

the knob.

Plug the refrigerator back in.

Freezer Compartment

Unplug the refrigerator.

Remove the shelf just above the light

shield. (The shelf will be easier to

remove if it is emptied first.) On some

models, a screw at the top of the light

shield will need to be removed.

To remove the light shield, press in

on the sides, and lift up and out.

Replace the bulb with an appliance

bulb of the same or lower wattage,

and reinstall the light shield. When

reinstalling the light shield, make

sure the top tabs snap securely

into place. Replace the screw

(on some models).

Reinstall the shelf and plug the

refrigerator back in.

C

O

L

D

C

O

L

D

E

S

T

Dispenser (on some models)

Unplug the refrigerator.

The bulb is located on the dispenser

under the control panel.

Remove the light bulb by turning

it counterclockwise.

Replace the bulb with a bulb of the

same size and wattage.

Plug the refrigerator back in.

Tabs

19

Trim kits and decorator panels.

Read these instructions completely and carefully.

Before You Begin

Some models are equipped with trim kits that allow you to install door panels. You can order

pre-cut black, white, bisque or stainless steel decorator panels from GE Parts and Accessories,

800.626.2002, or you can add wood panels to match your kitchen cabinets.

Panels less than 1/4″ (6 mm) thick

When installing wood panels less than 1/4″ (6 mm) thick, you need to create a filler panel, such as 1/8″

cardboard, that will fit between the face of the door and the wood panel. If you are installing the pre-cut

decorator panels, pre-cut filler panels are included in the kit. The combined thickness of the decorator

or wood panel and the filler panel should be 1/4″ (6 mm).

For CustomStyle

™

models

3/4″ (19 mm) or Raised Panel

A raised panel design screwed or glued to a 1/4″ (6 mm) thick backing, or a 3/4″ (19 mm) routed board

can be used. The raised portion of the panel must be fabricated to permit clearances of at least 2″ (5.1 cm)

from the handle side for fingertip clearance.

Panels thicker than 1/4″ (6 mm), up to 3/4″ (19 mm) max, will require that the outer 5/16″ (8 mm) of

panel perimeter be no thicker than 1/4″ (6 mm).

Weight limitations for custom panels:

Fresh Food 38 lbs. (17 kg) max.

Freezer Door 28 lbs. (13 kg) max.

2″ (5.1 cm)

Clearance

Handle Side

Appearance

Panel

Refrigerator

Door

1/4″ (6 mm)

Thick Backing

3/4″

(19 mm)

Panels 1/4″ thick or less

Panels thicker than 1/4″ (6 mm)

1/4″ max

1/4″ (6 mm) max

3/4″ (19 mm)

5/16″ (8 mm)

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

Consumer Support

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

20

Trim kits and decorator panels.

Freezer Panel

Without Dispenser

Freezer Panel

With Dispenser Fresh Food Panel

Cutout

5/16″

(8 mm)

14

15

⁄32″

(36.8 cm)

67

9

⁄32″

(170.9 cm)

1/8″ (3 mm)

FRONT

17

7

⁄8″

(45.4 cm)

14

15

⁄32″

(36.8 cm)

33

5

⁄8″

(85.4 cm)

FRONT

67

9

⁄32″

(170.9 cm)

19

15

⁄32″

(49.5 cm)

FRONT

23‘ Dimensions for Custom Wood Panels

The areas at the top of the panels need to be cut out of the panels.

25‘

CustomStyle

™

Dimensions for Custom Wood Panels

The areas at the top of the panels need to be cut out of the panels.

Cutout

1/8″ (3 mm)

Cutout

1/8″ (3 mm)

5/16″

(8 mm)

5/16″

(8 mm)

Freezer Panel

Without Dispenser

Freezer Panel

With Dispenser Fresh Food Panel

Cutout

5/16″

(8 mm)

14

15

⁄32″

(36.8 cm)

69

25

⁄32″

(177.3 cm)

1/8″ (3 mm)

FRONT

17

25

⁄32″

(45.2 cm)

14

15

⁄32″

(36.8 cm)

36

1

⁄4″

(92.0 cm)

FRONT

69

25

⁄32″

(177.3 cm)

19

15

⁄32″

(49.5 cm)

FRONT

Cutout

1/8″ (3 mm)

Cutout

1/8″ (3 mm)

5/16″

(8 mm)

5/16″

(8 mm)

La page est en cours de chargement...

GE Profile PSC23NGNWW Le manuel du propriétaire

GE Profile PSC23NGNWW Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents