Aiwa CSD-TD30 Manuel utilisateur
- Catégorie
- Lecteur CD
- Taper
- Manuel utilisateur
Ce manuel convient également à
Owner’s Record
The model number is located at the bottom and the serial
number is located in the battery compartment.
Record the serial number in the space provided below. Refer
to these numbers whenever you call upon your Aiwa dealer
regarding this product.
Model No. Serial No.
© 2003 Sony Corporation
CD STEREO RADIO CASSETTE RECORDER
CSD-TD10
CSD-TD30
3-249-839-11
2 ENGLISH
IMPORTANT SAFETY
Read the Operating Instructions carefully and
completely before operating the unit. Be sure to keep
the Operating Instructions for future reference. All
warnings and cautions in the Operating Instructions and
on the unit should be strictly followed, as well as the
safety suggestions below.
Warning
To prevent electric shock or injury, these safety
instructions should be followed in the installation, use
and servicing the unit.
Installation
Attachments – Do not use attachments not
recommended by the unit manufacturer as they may
result in the risk of fire, electric shock or injury to
persons.
Water and Moisture – Do not use this unit near water
- for example, near a bathtub, washbowl, kitchen sink,
or laundry tub, in a wet basement, or near a swimming
pool, and the like.
Heat – Do not use this unit near sources of heat,
including heating vents, stoves, or other appliances that
generate heat. It also should not be placed in
temperatures less than 5˚C (41˚F) or greater than 35˚C
(95˚F).
Mounting surface – Place the unit on a flat, even
surface.
Accessories – Do not place this unit on an unstable
cart, stand, tripod, bracket, or table. The unit may fall,
causing serious injury to a child or an adult, and serious
damage to the appliance. Use only with a cart, stand,
tripod, bracket, or table recommended by the
manufacturer, or sold with the unit. Any mounting of the
appliance should follow the manufacturer’s instructions,
and should use a mounting accessory recommended by
the manufacturer.
Portable cart – An appliance and cart
combination should be moved with
care. Quick stops, excessive force, and
uneven surfaces may cause the
appliance and cart combination to
overturn.
Ventilation – The unit should be situated with
adequate space around it so that proper heat ventilation
is assured. Allow 10 cm clearance from the rear and the
top of the unit, and 5 cm from the each side.
Slots and openings in the cabinet and the back or
bottom are provided for ventilation, and to ensure
reliable operation of the unit and to protect it from
overheating, these openings must not be blocked or
covered. The openings should never be blocked by
placing the unit on a bed, sofa, rug or other similar
surface. This unit should not be placed in a built-in
installation such as a bookcase unless proper
ventilation is provided.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.
Explanation of Graphical Symbols:
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended
to alert the user to the presence of
uninsulated “dangerous voltage” within the
product’s enclosure that may be of
sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an
equilateral triangle is intended to alert the
user to the presence of important
operating and maintenance (servicing)
instructions in the literature accompanying
the appliance.
“CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.”
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
The use of optical instruments with this product will
increase eye hazard.
ENGLISH 3
Object and Liquid Entry – Never push objects of any
kind into this unit through the cabinet slots as they may
touch dangerous voltage points or short-circuit parts
that could result in a fire or electric shock. Never spill
liquid of any kind on the unit.
Electric Power
Power Sources – This unit should be operated only
from the type of power source indicated on the marking
label. If you are not sure of the type of power supply to
your home, consult your appliance dealer or local power
company. To operate unit on battery power, or other
sources, refer to the operating instructions.
Grounding or Polarization – This unit is provided
with a polarized alternating-current line plug (a plug
having one blade wider than the other). This plug will fit
into the power outlet only one way. This is a safety
feature. If you are unable to insert the plug fully into the
outlet, try reversing the plug. If the plug should still fail
to fit, contact your electrician to replace your obsolete
outlet. Do not defeat the safety purpose of the polarized
plug.
Power-Cord Protection – Power-supply cords should
be routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying
particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the
product.
Overloading – Do not overload wall outlets, extension
cords, integral convenience receptacles as this can
result in a risk of fire or electric shock.
Lightning
For added protection for this unit receiver during a
lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall
outlet. This will prevent damage to the unit due to
lightning and powerline surges.
Maintenance
Cleaning – Unplug this unit from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
Condensation – Moisture may form on the CD pickup
lens when:
- The unit is moved from a cold spot to a warm spot
- The heating system has just been turned on
- The unit is used in a very humid room
- The unit is cooled by an air conditioner
When this unit has condensation inside, it may not
function normally. Should this occur, leave the unit for a
few hours, then try to operate again.
INSTRUCTIONS
Damage Requiring Service
Unplug this unit from the wall outlet and refer servicing
to qualified service personnel under the following
conditions:
1) When the power cord or plug is damaged.
2) If liquid has been spilled, or objects have fallen into
the unit.
3) If the unit has been exposed to rain or water.
4) If the unit does not operate normally by following the
operating instructions. Adjust only those controls
that are covered by the operating instructions as
improper adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore the unit to normal
operation.
5) If the unit has been dropped or the cabinet has been
damaged.
6) When the unit exhibits a distinct change in
performance - this indicates a need for service.
Do not attempt to service this unit yourself as opening
or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified
service personnel.
Replacement Parts – When replacement parts are
required, be sure the service technician has used
replacement parts specified by the manufacturer or
having the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric
shock or other hazards.
Safety Check – Upon the completion of any service or
repairs to this unit, ask the service technician to perform
safety checks to determine that the unit is in proper
operating condition.
Power supply
Using on AC house current
Connect the AC cord as illustrated below.
CAUTION
Use only the supplied AC cord. Use with other cords
may result in the risk of fire.
Using on batteries
Open the lid of the battery compartment on the rear and
insert eight R14 (size C) batteries, not supplied, with
the 0 and 9 marks correctly aligned. Then close the
lid.
To switch from AC power supply to battery power
supply, disconnect the AC cord from the AC inlet.
R14 (C)
When to replace the batteries
The tape speed slows down, volume decreases, or
sound is distorted during operation.
Notes on batteries
•Do not mix different types of batteries or old batteries
with new ones.
•When the unit is not to be used for a long period,
remove the batteries to prevent needless battery
wear.
•Never recharge the batteries, apply heat to them or
take them apart.
•Remove dead batteries.
If liquid leaks from the batteries, wipe thoroughly to
remove.
4 ENGLISH
to the AC inlet of the unit
to an AC outlet
(AC 120 V, 60 Hz)
supplied AC cord
SOUND ADJUSTMENT
Volume or tone adjustment does not affect
recording.
VOLUME
Turn VOLUME to adjust.
T-BASS system
The T-BASS system enhances the realism of low-
frequency sound.
Set T-BASS to ON or OFF.
Remote control (CSD-TD30 only)
Insert two R6 (size AA) batteries.
R6 (AA)
When the reach of the remote control signal is less than
5 meters (16 feet), replace the batteries.
The remote control may not operate correctly
when:
- The unit is exposed to intense light, such as direct
sunlight
-Objects block the remote control signal to the unit
To use the buttons on the remote control
Buttons on the remote control and the main unit with
identical indications have the same functions.
ENGLISH 5
Use Type I (normal) tapes only.
INSERTING A TAPE
Press Z STOP/EJECT to open the cassette
holder and insert a tape with the exposed side
up and the side to be played facing out.
Push the cassette holder to close.
PLAYING A TAPE
Press x PLAY while the power is off.
The power is turned on and play of the inserted tape
begins.
Z STOP/EJECT – Stops play. The power will be
automatically turned off.
a PAUSE – Pauses play. To resume play, press
again.
f FF/ g REW – Fast forwards/ rewinds. To stop
the winding, press Z.
TAPE OPERATION
A
RECORDING
Note that recording is done on only one side of the
tape.
1
Insert a tape with the side to be recorded
facing out.
2
Get ready to record from the source.
To record from a CD, select CD and load the disc.
To record from a radio broadcast, select RADIO
and tune to a station.
(See the following pages.)
3
Press w REC to start recording.
x PLAY is pressed simultaneously.
When recording from a CD, press e to start
playback.
To record only the selected tracks of a CD
1 Follow steps 1 to 4 of PROGRAMMED PLAY on
page 9 to program tracks.
2 Press w, then start CD play.
To stop recording, press Z. To stop CD play, press
s.
To pause recording, press a. To resume recording,
press again.
To erase recording, press w while the power is off.
After recording, select TAPE/6STANDBY with
FUNCTION to turn the power off.
To prevent accidental erasure
Break off the plastic tabs on the cassette tape with a
screwdriver or other pointed tool after recording.
To record on the tape again
Cover the tab openings with adhesive tape, etc.
Tab for side A
Side A
PAUSE
STOP/EJECT
FF REW PLAY
REC
6 ENGLISH
1
Select RADIO with FUNCTION.
The power is turned on.
2
Press s repeatedly to select the desired
band.
FM AM
The previously tuned station is received.
3
Press r, t to select a station.
During FM stereo reception, is displayed.
After listening, select TAPE/6STANDBY with
FUNCTION to turn the power off.
For better reception
For quick tuning (Auto Search)
Hold down r, t until the tuner starts searching
for a station. When a station is tuned to, the search
stops.
If the broadcast signal is weak, it does not stop. To
stop the search manually, press r or t.
RADIO OPERATION
B
REPEAT/MODE
- If an FM stereo broadcast contains noise, press the
button so that is displayed.
Noise is reduced, although reception is monaural.
To restore stereo reception, press the button again.
- If a high-pitched sound is heard during AM recording,
press the button repeatedly to display “b1” or “b2”, so
as to eliminate the noise.
To change the AM tuning interval
The default setting of the AM tuning interval is 10 kHz/
step. If you use this unit in an area where the frequency
allocation system is 9 kHz/step, change the interval as
follows.
1 Press s to display AM.
2 Hold down REPEAT/MODE for 5 seconds to change
the interval.
When the AM tuning interval is changed, the AM preset
stations are cleared.
NOTE
If the unit picks up noise from other electrical
appliances nearby, like a TV or fluorescent lights, move
the unit away.
Extend the rod antenna
and orient it for the best
reception.
The antenna is inside the
unit. Position the unit for
the best reception.
AMFM
ENGLISH 7
PRESETTING STATIONS
You can preset up to 15 stations in each band.
1
Select a station.
2
Press PROGRAM once so that “M” is
displayed to store the station.
A station is assigned a preset number, beginning
from 1 in consecutive order for each band.
3
Repeat steps 1 and 2.
The next station will not be stored if a total of 15
preset stations have already been stored for a
band.
To listen to preset stations
Select a band then press e repeatedly.
To clear a preset station
Select the preset number first. Within 5 seconds, hold
down PROGRAM until “M” and the preset number
disappear in the display.
The higher numbers in the band are decreased by one.
Preset number
Frequency
Maintenance
To clean the cabinet
Use a soft cloth lightly moistened with mild
detergent solution. Do not use strong solvents
such as alcohol, benzine or thinner.
To clean the heads
When the tape heads are dirty;
- high frequency sound is not emitted
- the sound is not adequately high
- the sound is off-balance
- the tape cannot be erased
- the tape cannot be recorded on
After every 10 hours of use, clean the tape heads
with a head cleaning cassette.
Use separately sold dry-type or wet-type cleaning
cassette.
Refer to the instructions of the cleaning cassette
for details.
To clean the lens
Use a cotton swab
slightly moistened with
cleaning fluid. Wipe
gently from the center
to the edge.
Lens
(CSD-TD30 only)
8 ENGLISH
1
Select CD with FUNCTION.
The power is turned on.
2
Press PUSH OPEN to open the disc
compartment. Place a disc with the
printed side up and close the disc
compartment.
PUSH OPEN
Total number of tracks and total playing time are
displayed.
3
Press e to start play.
The number of the track being played and elapsed
playing time are displayed.
s – Stops play.
e – Pauses play. To resume play, press again.
r, t – Searches for a particular point during
playback. Hold down r or t and then release it.
–Skips to the beginning of a track. Press r or t
repeatedly.
REPEAT/MODE – Repeats a single track or all tracks.
Select as follows.
: A single track is played repeatedly. Select a
track with r or t.
: All tracks are played repeatedly.
CD OPERATION
C
After listening, select TAPE/ 6STANDBY with
FUNCTION to turn the power off.
NOTE
•Do not use irregular shape CDs (example: heart-
shaped, octagonal ones).
It may result in malfunctions.
•Do not place more than one disc in the disc
compartment.
•Do not try to open the disc compartment during play.
•Do not touch the lens. Doing so may cause
malfunctions.
• The unit may not play a CD-R disc that is recorded on
personal computers or some kinds of
CD-R recorders because of differences in recording
platforms.
•Do not attach any seal or label to either side (the
recordable side or the labeled side) of a CD-R disc. It
may cause malfunction.
•Do not load an unrecorded CD-R disc. It will take
over 30 seconds to read the disc. The disc may be
damaged if you try to open the disc compartment
while reading the disc.
Music discs encoded with copyright protection
technologies
This product is designed to playback discs that conform
to the Compact Disc (CD) standard.
Recently, various music discs encoded with copyright
protection technologies are marketed by some record
companies. Please be aware that among those
discs, there are some that do not conform to the CD
standard and may not be playable by this product.
ENGLISH 9
PROGRAMMED PLAY
Up to 16 tracks can be programmed from the disc.
1
In stop mode, press PROGRAM.
2
Press r, t to select a track, then
press PROGRAM to store it.
3
Repeat step 2 to program other tracks.
4
Press s to finish the program.
5
Press e to start play.
To check the program, press r or t in stop
mode.
To clear the program, hold down PROGRAM in stop
mode until the display changes.
To change the programmed tracks, clear the
program and repeat all the steps again.
Specifications
Radio section
Frequency range, antenna – FM: 87.5 - 108.0 MHz Rod
antenna, AM: 530/531 - 1,710/1,602 kHz (10/9 kHz
step) Ferrite bar antenna
Deck section
Track format – 4 tracks, 2 channels / Frequency range
– Normal tape: 50 - 12,500 Hz (JEITA) / Recording
system – AC bias / Erasing system – Magnet erase /
Heads – Recording/playback head (1), Erasure head
(1)
CD player section
Disc – Compact disc / Scanning method – Non-contact
optical scanner (semiconductor laser) /
Laser diode properties –
Material: GaAlAs
Wavelength: λ = 780 nm
Emission duration: Continuous
Laser output: Less than 44.6 µW (This output is the
value measured at a distance of 200 mm from the
objective lens surface on the optical pick-up block with
7 mm aperture.)
General
Speaker – 100 mm cone type (2) / Power output –
2 W + 2 W (JEITA 8 ohms, T.H.D. 10% DC) / Power
requirements – DC 12 V using eight size C (R14)
batteries, AC 120 V, 60 Hz / Power consumption – 12
W / Dimensions (W × H × D) – 390 × 170 × 258.5 mm
(15
3
/
8
× 6
3
/
4
× 10
1
/
4
in.) / Weight (excluding batteries)
– 2.7 kg (5 lbs. 15 oz.) / Accessory – Remote control
(1, CSD-TD30 only), AC cord (1)
Specifications and external appearance are subject to
change without notice.
COPYRIGHT
Please check the copyright laws relating to
recordings from disc, radio or external tape for the
country in which the machine is being used.
If an erroneous display or malfunction occurs
Select CD function first. Hold down s and press e.
If the unit cannot be reset in the way above, disconnect
the AC cord and remove all the batteries to turn off the
display.
Leave the unit for a while and turn the power back on.
Track number
Program number
Total number of
the programmed tracks
(CSD-TD30 only)
Sony Corporation Printed in China http://www.aiwa.com/
NOTE
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
... Reorient or relocate the receiving antenna.
... Increase the separation between the equipment and
receiver.
... Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
... Consult the dealer or an experienced radio/TV
technician for help.
CAUTION
Modifications or adjustments to this product, which are
not expressly approved by the manufacturer, may void
the user’s right or authority to operate this product.
CAUTION
TO PREVENT ELECTRIC SHOCK DO NOT USE THIS
(POLARIZED) PLUG WITH AN EXTENSION CORD,
RECEPTACLE OR OTHER OUTLET UNLESS THE
BLADES CAN BE FULLY INSERTED TO PREVENT
BLADE EXPOSURE.
This Class B digital apparatus complies with Canadian
ICES-003.
REMARQUE
Cet appareil a été testé et jugé conforme aux limites
des appareils numériques de Classe B, conformément
à la Partie 15 des Règles FCC. Ces limites sont
conçues pour fournir une protection raisonnable contre
les interférences néfastes dans une installation
résidentielle.
Cet appareil produit, utilise et peut rayonner une
énergie de fréquence radio et, s’il n’est pas installé et
utilisé conformément aux instructions, peut provoquer
des interférences gênantes pour les communications
radio. Mais rien ne garantit qu’une telle interférence ne
se produira pas dans une installation particulière. Si cet
appareil produit des interférences gênantes pour la
réception radio ou de télévision, ce qui peut se
déterminer en allumant et éteignant l’appareil, il est
recommandé à l’utilisateur d’essayer de corriger cette
interférence en appliquant une ou plusieurs des
méthodes ci-dessous.
... Réorientation ou déplacement de l’antenne
réceptrice.
... Eloignement de l’appareil du récepteur.
... Raccordement de l’appareil à une prise d’un circuit
différent de celui du récepteur.
... Consultez le revendeur ou un technicien radio/
télévision expérimenté.
PRÉCAUTION
Les modifications ou ajustements de ce produit, non
expressément approuvés par le fabricant, peuvent
invalider la droit ou l’autorité de l’utilisateur à utiliser ce
produit.
ATTENTION
POUR PREVENIR LES CHOCS ELECTRIQUES NE
PAS UTILISER CETTE FICHE POLARISEE AVEC UN
PROLONGATEUR, UNE PRISE DE COURANT OU
UNE AUTRE SORTIE DE COURANT, SAUF SI LES
LAMES PEUVENT ETRE INSEREES A FOND SANS
EN LAISSER AUCUNE PARTIE A DECOUVERT.
Cet appareil numérique de la classe B est conforme à
la norme NMB-003 du Canada.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
Aiwa CSD-TD30 Manuel utilisateur
- Catégorie
- Lecteur CD
- Taper
- Manuel utilisateur
- Ce manuel convient également à
dans d''autres langues
- English: Aiwa CSD-TD30 User manual
Documents connexes
-
Aiwa CSD-TD901 Manuel utilisateur
-
-
-
-
-
-
-
-