Simplicity ENG, MDL 610000 Manuel utilisateur

Marque: Simplicity

Modèle: ENG, MDL 610000

Taper: Manuel utilisateur

Operator's Manual

Betjeningsvejledning

Bedienungsanleitung

Εγχειρίδιο χρήσ

Manual del operador

Käyttäjän käsikirja

Manuel d'utilisation

Manuale dell’Operatore

Gebruiksaanwijzing

Brukerhåndbok

Manual do Operador

Instruktionsbok

Models:54E000,540000,61E000,610000,61G200,

61G300

Revision A

Not for

Reproduction

2 vanguardpower.com

Not for

Reproduction

Not for

Reproduction

General Information

This manual contains safety information so that you will know the hazards and risks

related to this engine and how to prevent them. It also contains instructions for the

correct use and maintenance of the engine. Because Briggs & Stratton does not know

what equipment this engine will power, it is important that you read, understand, and

obey these instructions. Save these original instructions for future reference.

NOTE:The figures and illustrations in this manual are for reference only and can be

different from your model. If you need help, contact an Authorized Service Dealer.

For replacement parts or technical help, record the date of purchase, engine model,

type, trim, and the engine serial number. These numbers are located on your engine.

Refer to the Features and Controls section.

Date of Purchase

Engine Model - Type - Trim

Engine Serial Number

European Office Contact Information

For questions related to European emissions, contact our European office at:

Max-Born-Straße 2, 68519 Viernheim, Germany.

European Union (EU) Stage V (5): Carbon

Dioxide (CO2) Values

Enter CO2 in the search window on BriggsandStratton.com to find carbon dioxide values

of Briggs & Stratton EU Type-Approval Certificate engines.

Recycling Information

Recycle all cartons, boxes, used oil, and batteries as

specified by government regulations.

Operator Safety

Safety Alert Symbol and Signal Words

The safety alert symbol identifies safety information about hazards that could

result in personal injury. A signal word (DANGER, WARNING, or CAUTION) is used to

indicate the likelihood and the potential severity of injury. In addition, a hazard symbol

is used to represent the type of hazard.

DANGER indicates a hazard which, if not avoided, will result in death or serious injury.

WARNING indicates a hazard which, if not avoided, could result in death or serious

injury.

CAUTION indicates a hazard which, if not avoided, could result in minor or moderate

injury.

NOTICE indicates information considered important but not hazard-related.

Hazard Symbols and Meanings

Safety information about

hazards that can result in

personal injury.

Read and understand the

Operator's Manual before

operating or servicing the

unit.

Fire Hazard Explosion Hazard

Shock Hazard Toxic Fume Hazard

Hot Surface Hazard Noise Hazard - Ear

protection recommended

for extended use.

Thrown Object Hazard -

Wear eye protection.

Explosion Hazard

Frostbite Hazard Kickback Hazard

Amputation Hazard -

Moving Parts

Chemical Hazard

Thermal Heat Hazard Corrosive Hazard

Safety Messages

WARNING

Briggs & Stratton® Engines are not designed for and are not to be used to power:

fun-karts; go-karts; children's, recreational, or sport all-terrain vehicles (ATVs);

motorbikes; hovercraft; aircraft products; or vehicles used in competitive events not

sanctioned by Briggs & Stratton. For information about competitive racing products, see

www.briggsracing.com. For use with utility and side-by-side ATVs, please contact Briggs

& Stratton Power Application Center, 1-866-927-3349. Incorrect engine use could result

in serious injury or death.

WARNING

Fuel and its vapors are flammable and explosive. Fire or explosion could result in

burns or death.

When you add fuel

• Stop the engine. Before you remove the fuel cap, wait a minimum of two (2)

minutes to make sure that the engine is cool.

• Fill the fuel tank outdoors or in an area that has good airflow.

• Do not put too much fuel in the tank. For expansion of the fuel, do not fill above

the bottom of the fuel tank neck.

• Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition

sources.

• Frequently examine the fuel lines, fuel tank, fuel cap, and connections for cracks

or leaks. Replace damaged parts.

• If fuel spills, wait until it dries before you start the engine.

When you start the engine

• Make sure that the spark plug, muffler, fuel cap and air cleaner (if equipped) are

correctly installed.

• Do not crank the engine with the spark plug removed.

• If the engine is flooded, set the choke (if equipped) to the OPEN or RUN

position. Move the throttle (if equipped) to the FAST position and crank until the

engine starts.

• If there is natural or LP gas leakage in the area, do not start the engine.

• Because vapors are flammable, do not use pressurized starter fluids.

When you operate the equipment

• Do not tilt the engine or the equipment at an angle which causes fuel to spill.

• Do not choke the carburetor (if equipped) to stop the engine.

• Do not start or operate the engine with the air cleaner (if equipped) or the air

filter (if equipped) removed.

When you do maintenance

• If you drain the oil from the top oil fill tube, the fuel tank must be empty. If it is not

empty, fuel leakage can occurand could result a fire or an explosion.

• During maintenance if it is necessary to tilt the unit, make sure that the fuel tank,

if mounted on the engine, is empty and that the spark plug side is up. If the fuel

tank is not empty, leakage can occurand could result a fire or an explosion.

• Frequently examine the fuel lines, fuel tank, fuel cap, and connections for cracks

or leaks. Replace damaged parts.

• Do not change the governor spring, links or other parts to increase engine

speed.

• Do not hit the flywheel with a hammer or hard object. This could result in failure

of the flywheel during operation.

• Replacement parts must be of the same design and installed in the same

position as the original parts. Other parts could result in damage or an injury.

4 vanguardpower.com

Not for

Reproduction

When you move the location of equipment

• Make sure that the fuel tank is EMPTY or that the fuel shut-off valve is in the

CLOSED position.

When fuel or equipment is in storage with fuel in the fuel tank

• Because pilot lights or other ignition sources can cause explosions, keep fuel or

equipment away from furnaces, stoves, water heaters or other appliances that

have pilot lights.

WARNING

Fuel and its vapors are flammable and explosive. Fire or explosion could result in

burns or death.

Engine start-up causes spark that could result in a fire or explosion.

• If there is natural or LP gas leakage in the area, do not start the engine.

• Because vapors are flammable, do not use pressurized starter fluids.

WARNING

POISONOUS GAS HAZARD. Engine exhaust contains carbon monoxide, a

poisonous gas that could kill you in minutes. Although you do not smell exhaust

fumes, you could still be exposed to dangerous carbon monoxide gas. If you feel

sick, dizzy, or weak while you use this product, get to fresh air RIGHT AWAY. See

a doctor. You may have carbon monoxide poisoning.

• Carbon monoxide gas can collect in occupied spaces. To reduce the risk of

carbon monoxide gas, ONLY operate this product outdoors and far away from

windows, doors and vents.

• Install battery-operated carbon monoxide alarms or plug-in carbon monoxide

alarms with battery back-up as specified by the manufacturer's instructions.

Smoke alarms cannot sense carbon monoxide gas.

• DO NOT operate this product in homes, garages, basements, crawlspaces,

sheds, or other closed spaces, even if you use fans or open doors and windows

for ventilation. After the operation of this product, carbon monoxide can quickly

collect in these spaces and stay for hours.

• ALWAYS put this product downwind and point the engine exhaust away from

occupied spaces.

WARNING

Fast retraction of the starter cord (kickback) will pull your hand and arm to the

engine faster than you can let go.Broken bones, fractures, bruises or sprains

could result.

• To prevent kickback when you start the engine, pull the starter cord slowly until

resistance is felt and then pull quickly.

• Before you start the engine, disconnect or remove all external equipment and

engine loads.

• Make sure that direct-coupled equipment components, such as, but not limited

to, blades, impellers, pulleys, and sprockets, are correctly attached.

WARNING

Rotating parts can entangle hands, feet, hair, clothing, or accessories and result

in traumatic amputation or laceration.

• Operate equipment with the guards correctly installed.

• Keep hands and feet away from rotating parts.

• Remove jewelry and make sure that long hair is away from all rotating parts.

• Do not wear loose clothes or items that could become caught.

WARNING

During operation, the engine and muffler become hot. If you touch a hot engine,

thermal burns can occur.

Combustible materials, such as leaves, grass and brush, can catch fire.

• Before you touch the engine or muffler, stop the engine and wait two (2)

minutes. Make sure that the engine and muffler are safe to touch.

• Remove debris from the muffler and engine.

It is a violation of California Public Resource Code, Section 4442, to use or operate the

engine on any forest-covered, brush-covered, or grass-covered land unless the exhaust

system is equipped with a spark arrester, as defined in section 4442, maintained in

effective working order. Other states or federal jurisdictions may have similar laws;

reference Federal Regulation 36 CFR Part 261.52. Contact the original equipment

manufacturer, retailer, or dealer to obtain a spark arrester designed for the exhaust

system installed on this engine.

WARNING

Accidental engine spark can cause an electric shock or fire and could result in

entanglement, traumatic amputation or laceration.

Before you make adjustments or repairs:

• Disconnect the spark plug wire and keep it away from the spark plug.

• Disconnect the battery wire from the negative battery terminal (only engines with

electric start.)

• Use only the correct tools.

When you check for spark:

• Use an approved spark plug tester.

• Do not check for spark with the spark plug removed.

WARNING

Fuel vapors are flammable and explosive. Fire or explosion could result in burns

or death.

If you smell gas

• Do not start the engine.

• Do not switch on electrical switches.

• Do not use a phone in the vicinity.

• Evacuate the area.

• Contact the gas supplier or the fire department.

Features and Controls

Engine Controls

Compare the callout letters in Figures 1, 2, 3, and 4 to the engine controls in the list that

follows:

A. Engine Identification Numbers Model - Type - Code

B. Spark Plug

C. Cyclonic Air Cleaner

D. Low Profile Air Cleaner

E. Dipstick

F. Oil Fill

G. Oil Filter

H. Oil Drain Plug

I. Oil Pressure Sensor

J. Finger Guard

K. Electric Starter

L. Starter Solenoid

M. Regulator / Rectifier

N. Carburetor - Carburetor Models

O. Oil Cooler (if equipped)

P. Muffler (if equipped)

Q. Fuel Pump

Starter Switch

Throttle Control

ChokeControl(Carburetor Models

)

U. Fuel Filter

V. Tachometer (if equipped)

Some engines and equipment have remote controls. See the equipment manual for the

location and operation of remote controls.

Engine Control Symbols and Meanings

Engine Speed - FAST Engine Speed - SLOW

Engine Speed - STOP ON - OFF

Not for

Reproduction

Engine Start

Choke CLOSED

Engine Start

Choke OPEN

Fuel Cap

Fuel Shut-off OPEN

Fuel Shut-off CLOSED

Fuel Level - Maximum

Do Not Overfill

Operation

Oil Recommendations

Oil Capacity: See the Specifications section.

NOTICE

This engine was shipped from Briggs & Stratton without oil. Equipment manufacturers or

dealers could have added oil to the engine. Before you start the engine for the first time,

make sure that the oil is at the correct level. Add oil as specified by the instructions in

this manual. If you start the engine without oil, damage will occur and the engine will not

be repaired under warranty.

We recommend the use of Briggs & Stratton

Warranty Certified oils for best

performance. Other high-quality detergent oils are permitted if classified for service SF,

SG, SH, SJ or higher. Do not use special additives.

Use the chart to select the best viscosity for the outdoor temperature range expected.

Engines on most outdoor power equipment operate well with 5W-30 Synthetic oil. For

equipment operated in hot temperatures, Vanguard

15W-50 Synthetic oil gives the best

protection.

A SAE 30 - Below 40 °F (4 °C) the use of SAE 30 will result in hard starting.

B 10W-30 - Above 80 °F (27 °C) the use of 10W-30 may cause increased oil

consumption. Checkthe oil level frequently.

C 5W-30

D Synthetic 5W-30

Vanguard

Synthetic 15W-50

Check and Add Oil

Before you check or add oil

• Make sure the engine is level.

• Clean the oil fill area of debris.

• Refer to the Specifications section for oil capacity.

NOTICE

This engine was shipped from Briggs & Stratton without oil. Equipment manufacturers or

dealers could have added oil to the engine. Before you start the engine for the first time,

make sure that the oil is at the correct level. Add oil as specified by the instructions in

this manual. If you start the engine without oil, damage will occur and the engine will not

be repaired under warranty.

1. Remove the dipstick (A, Figure 5) and clean with a cloth.

2. Install and tighten the dipstick (A, Figure 5).

3. Remove the dipstick and check the oil level. Make sure that the oil level is at the

top of the full indicator (B, Figure 5) on the dipstick.

4. If the oil level is low, slowly add oil into the engine oil fill (C, Figure 5). Do not add

too much oil. After you add oil, wait one minute and check the oil level again. Make

sure that the oil level is correct.

5. Install and tighten the dipstick (A, Figure 5).

Low Oil Protection System (if equipped)

A low oil sensor is installed on some engines. If the oil is low, the sensor will display a

warning light or stop the engine. Stop the engine and follow these steps before you start

the engine.

• Make sure the engine is level.

• Do an oil check. Refer to the Check Oil Level section.

• If the oil level is low, add the correct amount of oil. Start the engine and make

sure the warning light (if equipped) does not come on.

• If the oil level is not low, do not start the engine. Contact a Briggs & Stratton

Authorized Service Dealer to have the oil problem corrected.

Fuel Recommendations

Fuel must meet these requirements:

• Clean, fresh, unleaded gasoline.

• A minimum of 87 octane/87 AKI (91 RON). High altitude use, see below.

• Gasoline with up to 10% ethanol (gasohol) is permitted.

NOTICE

Do not use unapproved gasoline, such as E15 and E85. Do not mix oil in gasoline or

change the engine to operate on alternate fuels. Use of unapproved fuels could result in

damage to engine components, which will not be repaired under the warranty.

To protect the fuel system from gum formation, mix a fuel stabilizer into the fuel. Refer

to the Storage section. All fuel is not the same. If start or performance problems occur,

change fuel providers or brands. This engine is certified to operate on gasoline. The

emissions control system for carbureted engines is EM (Engine Modifications). The

emissions control systems for engines with electronic fuel injection are ECM (Engine

Control Module), MPI (Multi Port Injection), and if equipped an O2S (Oxygen Sensor).

High Altitude

At altitudes over 5,000 feet (1524 meters), a minimum 85 octane/85 AKI (89 RON)

gasoline is permitted.

For carbureted engines, high altitude adjustment is required to maintain performance.

Operation without this adjustment will cause decreased performance, increased fuel

consumption, and increased emissions. Contact a Briggs & Stratton Authorized Service

Dealer for high altitude adjustment information. Operation of the engine at altitudes

below 2,500 feet (762 meters) with the high altitude adjustment is not recommended.

For Electronic Fuel Injection (EFI) engines, no high altitude adjustment is necessary.

Add Fuel

WARNING

Fuel and its vapors are flammable and explosive. Fire or explosion could result in

burns or death.

When you add fuel

• Stop the engine. Before you remove the fuel cap, wait a minimum of two (2)

minutes to make sure that the engine is cool.

• Fill the fuel tank outdoors or in an area that has good airflow.

• Do not put too much fuel in the tank. For expansion of the fuel, do not fill above

the bottom of the fuel tank neck.

• Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition

sources.

• Frequently examine the fuel lines, fuel tank, fuel cap, and connections for cracks

or leaks. Replace damaged parts.

• If fuel spills, wait until it dries before you start the engine.

1. Clean the fuel cap area of dirt and debris. Remove the fuel cap.

2. Fill the fuel tank (A, Figure 6) with fuel. Because fuel will expand, do not fill above

the bottom of the fuel tank neck (B).

3. Install the fuel cap.

Start and Stop Engine

Start Engine

WARNING

Fast retraction of the starter cord (kickback) will pull your hand and arm to the

engine faster than you can let go.Broken bones, fractures, bruises or sprains

could result.

• To prevent kickback when you start the engine, pull the starter cord slowly until

resistance is felt and then pull quickly.

• Before you start the engine, disconnect or remove all external equipment and

engine loads.

• Make sure that direct-coupled equipment components, such as, but not limited

to, blades, impellers, pulleys, and sprockets, are correctly attached.

6 vanguardpower.com

Not for

Reproduction

WARNING

Fuel and its vapors are flammable and explosive. Fire or explosion could result

in burns or death.

When you start the engine

• Make sure that the spark plug, muffler, fuel cap and air cleaner (if equipped)

are correctly installed.

• Do not crank the engine with the spark plug removed.

• If the engine is flooded, set the choke (if equipped) to the OPEN or RUN

position. Move the throttle (if equipped) to the FAST position and crank until the

engine starts.

• If there is natural or LP gas leakage in the area, do not start the engine.

• Because vapors are flammable, do not use pressurized starter fluids.

WARNING

POISONOUS GAS HAZARD. Engine exhaust contains carbon monoxide, a

poisonous gas that could kill you in minutes. Although you do not smell exhaust

fumes, you could still be exposed to dangerous carbon monoxide gas. If you feel

sick, dizzy, or weak while you use this product, get to fresh air RIGHT AWAY.

See a doctor. You may have carbon monoxide poisoning.

• Carbon monoxide gas can collect in occupied spaces. To reduce the risk of

carbon monoxide gas, ONLY operate this product outdoors and far away from

windows, doors and vents.

• Install battery-operated carbon monoxide alarms or plug-in carbon monoxide

alarms with battery back-up as specified by the manufacturer's instructions.

Smoke alarms cannot sense carbon monoxide gas.

• DO NOT operate this product in homes, garages, basements, crawlspaces,

sheds, or other closed spaces, even if you use fans or open doors and

windows for ventilation. After the operation of this product, carbon monoxide

can quickly collect in these spaces and stay for hours.

• ALWAYS put this product downwind and point the engine exhaust away from

occupied spaces.

NOTICE

This engine was shipped from Briggs & Stratton without oil. Equipment manufacturers

or dealers could have added oil to the engine. Before you start the engine for the

first time, make sure that the oil is at the correct level. Add oil as specified by the

instructions in this manual. If you start the engine without oil, damage will occur and the

engine will not be repaired under warranty.

Types of Starting Systems

Before you start the engine, you must know the type of starting system on your engine.

Your engine will have one of these types.

• Electronic Fuel Injection (EFI) System: An EFI system does not have a

choke or a primer.

• Choke System: This type of system has a choke to be used in cool

temperatures. Some models will have a separate choke control while others

will have a combination choke and throttle choke. It does not have a primer.

NOTE:Your equipment could have remote controls. Refer to the equipment manual for

location and operation of remote controls.

Electronic Fuel Injection (EFI) System

1. Check the engine oil. See the Check Oil Level section.

2. Make sure equipment drive controls, if equipped, are disengaged.

3. Move the fuel shut-off (A, Figure 7), if equipped, to the OPEN position.

4. Move the throttle control (B, Figure 7), if equipped, to the FAST position. Operate

the engine in the FAST position.

5. Turn the electric start switch (D, Figure 7) to the ON or START position.

NOTICETo extend the life of the starter, use short start cycles (five seconds maximum).

Wait one minute between start cycles.

If the engine does not start after 3or 4 times, contact your local dealer or goto

vanguardpower.com or call 1-800-999-9333.

Choke System

1. Check the engine oil. See the Check Oil Level section.

2. Make sure equipment drive controls, if equipped, are disengaged.

3. Move the fuel shut-off (A, Figure 7), if equipped, to the OPEN position.

4. Move the throttle control (B, Figure 7), if equipped, to the FAST position. Operate

the engine in the FAST position.

5. Move the choke control (C, Figure 7), or the combination choke and throttle (B,C) to

the CLOSED position.

NOTE:To start the engine with a dry fuel system, additional cranking time in the choke

position will be required. This will give the fuel pump time to prime the fuel system.

6. Turn the key switch (D, Figure 7) to the ON or START position.

7. If the engine starts but will not continue to operate, move the choke control (C,

Figure 7) to the OPEN position to start the engine.

NOTICETo extend the life of the starter, use short start cycles (five seconds maximum).

Wait one minute between start cycles.

8. As the engine warms, move the choke control (C, Figure 7) to the OPEN position.

If the engine does not start after 3or 4 times, contact your local dealer or goto

vanguardpower.com or call 1-800-999-9333.

Stop the Engine

WARNING

Fuel and its vapors are flammable and explosive. Fire or explosion could result in

burns or death.

• Do not choke the carburetor (if equipped) to stop the engine.

1. With the throttle control in the SLOW position, turn the electric start switch (D,

Figure 7) to the OFF position. Remove the key and keep it in a safe place out of the

reach of children.

2. After the engine stops, move the fuel shut-off (A, Figure 7), if equipped, to the

CLOSED position.

Maintenance

Maintenance Information

WARNING

During maintenance if it is necessary to tilt the unit, make sure that the fuel tank, if

mounted on the engine, is empty and that the spark plug side is up. If the fuel tank is not

empty, leakage can occur and could result in a fire or an explosion. If the engine is tilted

in a different direction, it will not easily start because of oil or fuel contamination of the air

filter or the spark plug.

We recommend that you see a Briggs & Stratton Authorized Service Dealer for all

maintenance and servicing of the engine and engine parts.

NOTICE

All the components used to build this engine must remain in place for correct operation.

WARNING

Accidental engine spark can cause an electric shock or fire and could result in

entanglement, traumatic amputation or laceration.

Before you make adjustments or repairs:

• Disconnect the spark plug wire and keep it away from the spark plug.

• Disconnect the battery wire from the negative battery terminal (only engines with

electric start.)

• Use only the correct tools.

When you check for spark:

• Use an approved spark plug tester.

• Do not check for spark with the spark plug removed.

Emissions Control Service

For maintenance, replacement, or repair of emissions control devices and

systems, contact a qualified off-road engine repair establishment or service

technician. However, for "no charge" emissions control service, the work must be done

by a factory authorized dealer. Refer to the Emissions Control Statements.

Maintenance Schedule

Intervals of 8 Hours or Daily

• Check the engine oil level.

• Clean the area around the muffler and controls.

Intervals of 100 Hours or Annually

Not for

Reproduction

•

Clean or replace the air filter

1 2

• Change the engine oil and filter.

• Replace the oil filter (if equipped).

• Replace the spark plugs.

• Check the muffler and spark arrester.

• Service the exhaust system.

Intervals of 250 Hours or Annually

• Check the valve clearance. Adjust if necessary.

Intervals of 400 Hours or Annually

•

Change the air filter

• Replace the fuel filter.

•

Service the air cooling system

•

Clean the oil cooler fins

Intervals of 600 Hours

• Replace the safety filter, if equipped.

In dusty conditions or when airborne debris is present, clean more frequently.

Every third air filter change, replace the inner safety filter (if equipped.

Electronic Fuel Injection (EFI) System

The EFI System monitors engine temperature, engine speed, and battery voltage for

engine start-up and warm-up. There are no adjustments on the system. If start-up or

operation problems occur, contact a Briggs & Stratton Authorized Service Dealer.

NOTICEMake sure to obey the steps that follow or damage to the EFI system could

occur.

• DO NOT start the engine if the battery cables are loose.

• Turn the key to the OFF position before you disconnect, remove, and / or install

the battery.

• DO NOT use a battery charger to start the engine.

• DO NOT disconnect the battery cables during engine operation.

• When you disconnect the battery cables, first connect the positive (+) cable, and

then connect the negative (-) cable to the battery.

• When you charge the battery, turn the ignition switch to the OFF position,and

disconnect the negative (-) battery cable from the battery.

• DO NOT spray water directly on the Electronic Control Module.

Carburetor and Engine Speed

Do not make adjustments to the carburetor or engine speed. The carburetor was set at

the factory to operate satisfactorily under most conditions. Do not change the governor

spring, linkages, or other parts to adjust the engine speed. If any adjustments are

required contact a Briggs & Stratton Authorized Service Dealer for service.

NOTICE

The equipment manufacturer specifies the maximum speed for the engine as installed

on the equipment. Do not exceed this speed. If you are not sure what the equipment

maximum speed is, or what the engine speed is set to from the factory, contact a Briggs

& Stratton Authorized Service Dealer for assistance. For safe and correct operation

of the equipment, the engine speed should only be adjusted by a qualified service

technician.

Servicing the Spark Plug

Check the spark plug gap (A, Figure 8) with a wire gauge (B). If necessary, set the

spark plug gap. Install and tighten the spark plug to the correct torque. For gap or torque

specifications, refer to the Specifications section.

NOTE:In some areas, it is mandatory by local law that you use a resistor spark plug

to decrease ignition signals.If a resistor spark plug was installed by the equipment

manufacturer, use the same type for replacement.

Servicing theExhaust System

WARNING

During operation, the engine and muffler become hot. If you touch a hot engine,

thermal burns can occur.

Combustible materials, such as leaves, grass and brush, can catch fire.

• Before you touch the engine or muffler, stop the engine and wait two (2)

minutes. Make sure that the engine and muffler are safe to touch.

• Remove debris from the muffler and engine.

It is a violation of California Public Resource Code, Section 4442, to use or operate the

engine on any forest-covered, brush-covered, or grass-covered land unless the exhaust

system is equipped with a spark arrester, as defined in section 4442, maintained in

effective working order. Other states or federal jurisdictions may have similar laws;

reference Federal Regulation 36 CFR Part 261.52. Contact the original equipment

manufacturer, retailer, or dealer to obtain a spark arrester designed for the exhaust

system installed on this engine.

Remove debris from the muffler and cylinder area. Examine the muffler for cracks,

corrosion, or other damage. Remove the deflector or the spark arrester, if equipped, and

examine for damage or carbon blockage. If damage is found, install the replacement

parts before you operate the equipment.

WARNING

Replacement parts must be of the same design and installed in the same position as the

original parts. Other parts could result in damage or an injury.

Change Engine Oil

WARNING

Fuel and its vapors are flammable and explosive. Fire or explosion could result in

burns or death.

During operation, the engine and muffler become hot. If you touch a hot engine,

thermal burns can occur.

• If you drain the oil from the top oil fill tube, the fuel tank must be empty. If it is not

empty, fuel leakage can occur and cause a fire or an explosion.

• Before you touch the engine or muffler, stop the engine and wait two (2)

minutes. Make sure that the engine and muffler are safe to touch.

Used oil is a hazardous waste product and must be discarded of correctly. Do not

discard with household waste. Contact your local authorities, service center, or dealer

for safe disposal or recycling facilities.

Remove Oil

1. With engine OFF but warm, disconnect the spark plug wire(s)(D, Figure 9), and

keep it away from the spark plug(s)(E).

2. Remove the dipstick (A, Figure 10).

3. Remove the oil drain plug (F, Figure 11). Drain the oil into an approved container.

4. Install and tighten the oil drain plug(F, Figure 11).

Change Oil Filter, if equipped

1. Drain the oil from the engine. Refer to the Remove Oil section.

2. Remove the oil filter (H, Figure 12) anddiscard correctly.

3. Before you install the new oil filter, lightly lubricate the oil filter gasket withclean oil.

4. Install the oil filter by hand until the gaskettouchesthe oil filter adapter, then tighten

the oil filter 1/2 to 3/4 turns.

5. Add oil. Refer to the Add Oil section.

6. Start and operatethe engine. When the engine is warm, do a checkfor oil leaks.

7. Stop the engine. Make sure thatoil level is at the top of the full indicator (B, Figure

5) on the dipstick.

Add Oil

• Make sure the engine is level.

• Clean the oil fill area of all debris.

• Refer to the Specifications section for oil capacity.

1. Remove the dipstick (A, Figure 10). Remove oil from the dipstick with a clean cloth.

2. Slowly add oil into the engine oil fill (C, Figure 10). Do not overfill. Wait one

minute and then check the oil level.

3. Install and tighten the dipstick (A, Figure 10).

4. Remove the dipstick and check the oil level. The correct oil level is at the top of the

full indicator (B, Figure 10) on the dipstick.

5. Install and tighten the dipstick (A, Figure 10).

6. Connect the spark plug wire(s) (D, Figure 9) to the spark plug(s) (E).

Servicing the Air Filter

WARNING

Fuel vapors are flammable and explosive. Fire or explosion could result in burns

or death.

• Do notstart and operate the engine with the air cleaner assembly (if equipped)

or the air filter (if equipped) removed.

8 vanguardpower.com

Not for

Reproduction

NOTICE

Do not use pressurized air or solvents to clean the filter. Pressurized air could result in

damage to the filter and solvents will dissolve the filter.

See the Maintenance Schedule for service requirements.

Different models will use a foam or a paper filter. Some models could also have an

optional pre-cleaner that can be washed and used again. Compare the illustrations in

this manual with the type installed on your engine and service as follows.

Cyclonic Air Filter

1. Open the fastener(s) (A, Figure 13) and remove the cover (B).

2. Remove the air filter (C, Figure 13).

3. To loosen debris, lightly tap the air filter on a hard surface. If the air filter is dirty,

replace it with a new air filter.

4. To remove the safety filter (D, Figure 13), if equipped, carefully pull it away from the

air cleaner body (E). Make sure that dirt or debris does not go into the engine.

5. Install the new safety filter (D, Figure 13) in the air cleaner body (E).

6. Install the air filter (C, Figure 13) above the safety filter (D).

7. Install the cover (B, Figure 13) and close the fastener(s) (A).

Low Profile Air Filter

1. Remove the fastener(s) (A, Figure 14).

2. Remove the cover (B, Figure 14).

3. Remove the fastener(s) (C, Figure 14) and retainer (D).

4. Remove the air filter (E, Figure 14).

5. Remove the pre-cleaner (F, Figure 14), if equipped, from the air filter (E).

6. To loosen debris, lightly tap the air filter (E, Figure 14) on a hard surface. If the air

filter is dirty, replace with a new air filter.

7. Clean the pre-cleaner (F, Figure 14), if equipped, in liquid detergent and water.

Make sure the pre-cleaner is fully dry. Do not lubricate the pre-cleaner.

8. Assemble the dry pre-cleaner (F, Figure 14), if equipped, to the air filter (E).

9. Install the air filter (E, Figure 14) with the retainer (D) and fastener(s) (C).

10. Install the cover (B, Figure 14) with the fastener(s) (A). Make sure the fastener(s) is

tight.

Servicing the Cooling System

WARNING

During operation, the engine and muffler become hot. If you touch a hot engine,

thermal burns can occur.

Combustible debris, such as leaves, grass, and brush can catch fire.

• Before you touch the engine or muffler, stop the engine and wait two (2)

minutes. Make sure that the engine and muffler are safe to touch.

• Remove debris from the muffler and engine.

NOTICE

Do not use water to clean the engine. Water could cause contamination of the fuel

system. Use a brush or dry cloth to clean the engine.

This is an air cooled engine. Dirt or debris can stop the air flow and cause the engine to

become too hot and result in unsatisfactory performance and decreased engine life.

1. Use a brush or dry cloth to remove debris from the air intake area (A, Figure 15).

2. Keep linkage, springs, and controls (B, Figures 15, 16) clean.

3. Keep the area around and behind the muffler (C, Figures 15, 16) free of

combustible debris.

4. Make sure the oil cooler fins (D, Figure 15) are free of dirt and debris.

5. Loosen the fastener(s) (E, Figures 15, 16) and remove the debris access panels

(F). Remove grass and debris that has collected on the cylinders.

6. Install the debris access panels (F, Figures 15, 16) and attach with fastener(s) (E).

After a period of time, debris can collect in the cylinder cooling fins and cause the engine

to overheat. This debris cannot be removed without partial disassembly of the engine.

As recommended in the Maintenance Schedule, have a Briggs & Stratton Authorized

Service Dealer inspect and clean the air cooling system.

Servicing the Fuel System

WARNING

Fuel and its vapors are flammable and explosive. Fire or explosion could result in

burns or death.

• Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition

sources.

• Frequently examine the fuel lines, fuel tank, fuel cap, and connections for cracks

or leaks. Replace damaged parts.

• Before you clean or replace the fuel filter, drain the fuel tank or close the fuel

shut-off valve.

• If fuel spills, wait until it dries before you start the engine.

• Replacement parts must be of the same design and installed in the same

position as the original parts. Other parts could result in damage or an injury.

Fuel Filter, if equipped

1. Before you clean or replace the fuel filter (A, Figure 17), drain the fuel tank or close

the fuel shut-off valve. If the fuel tank is not drained, fuel leakage could occur and

cause a fire or explosion.

2. Use pliers to squeeze tabs (B, Figure 17) on the clamps (C), then move the clamps

away from the fuel filter (A). Twist and pull the fuel lines (D) off of the fuel filter.

3. Check the fuel lines (D, Figure 17) for cracks or leaks. Replace if necessary.

4. Replace the fuel filter (A, Figure 17) with an original equipment replacement filter.

5. Attach the fuel lines (D, Figure 17) with clamps (C).

Storage

Fuel System

Refer to Figure: 18.

Keep the engine level (normal operating position). Fill the fuel tank (A, Figure 18) with

fuel. For fuel expansion, do not fill above the fuel tank neck (B).

Fuel can become stale when kept in a storage container for more than 30 days. Each

time you fill the container with fuel, addto the fuel as specified by the manufacturer’s

instructions. This keeps fuel fresh and decreases fuel-related problems or contamination

in the fuel system.

It is not necessary to drain fuel from the engine whenis added as instructed. Before

storage, turn the engine ON for 2 minutes to move the fuel and stabilizer through the fuel

system.

If gasoline in the engine has not been treated with a fuel stabilizer, it must be drained

into an approved container. Operate the engine until it stops from lack of fuel. The use of

a fuel stabilizer in the storage container is recommended to keep fuel fresh.

Engine Oil

While the engine is still warm, change the engine oil. Refer to Change the Engine Oil

section.

Troubleshooting

Assistance

For assistance, contact your local dealer or go to vanguardpower.com or call

1-800-999-9333 (in USA).

Specifications

Specifications and Service Parts

Models: 540000 , 54E000

Displacement 54.68 ci (896 cc)

Bore 3.366 in ( 85,5 mm)

Stroke 3.071 in (78,0 mm)

Oil Capacity 78 - 80 oz (2,3 - 2,4 L)

Spark Plug Gap .030 in (,76 mm)

Spark Plug Torque 180 lb-in (20 Nm)

Armature Air Gap .005 - .008 in (,13 - ,20 mm)

Intake Valve Clearance .004 - .006 in(,10 - ,15 mm)

Exhaust Valve Clearance .007 - .009 in (,18 - ,23 mm)

Models: 610000, 61E000, 61G200, 61G300

Displacement 60.60 ci (993 cc)

Bore 3.366 in ( 85,5 mm)

Not for

Reproduction

Models: 610000, 61E000, 61G200, 61G300

Stroke 3.406 in (86,5 mm)

Oil Capacity 78 - 80 oz (2,3 - 2,4 L)

Spark Plug Gap .030 in (,76 mm)

Spark Plug Torque 180 lb-in (20 Nm)

Armature Air Gap .005 - .008 in (,13 - ,20 mm)

Intake Valve Clearance .004 - .006 in(,10 - ,15 mm)

Exhaust Valve Clearance .007 - .009 in (,18 - ,23 mm)

Service Parts - Models: 540000, 54E000,

610000, 61E000, 61G200, 61G300

Service Part Part Number

Cyclonic Air Filter (Figure 13) 841497

Cyclonic Safety Filter (Figure 13) 821136

Air Filter, Low Profile (Figure 14) 692519

Pre-cleaner, Low Profile (Figure 14) 692520

Oil - SAE 30 100028

Oil Filter 842921

Fuel Filter 691035

Resistor Spark Plug 491055

Long Life Platinum Spark Plug 5066

Spark Plug Wrench 19374

Spark Tester 19368

Engine power will decrease 3.5% for each 1,000 feet (300 meters) above sea level and

1% for each 10° F (5.6° C) above 77° F (25° C). The engine will operate satisfactorily

at an angle up to 15°. Refer to the equipment Operator's Manual for safe permitted

operating limits on slopes.

Power Ratings

The gross power rating for individual gasoline engine models is labeled in accordance

with SAE (Society of Automotive Engineers) code J1940 Small Engine Power & Torque

Rating Procedure, and is rated in accordance with SAE J1995. Torque values are

derived at 2600 RPM for those engines with “rpm” called out on the label and 3060 RPM

for all others; horsepower values are derived at 3600 RPM. The gross power curves

can be viewed at www.BRIGGSandSTRATTON.COM. Net power values are taken with

exhaust and air cleaner installed whereas gross power values are collected without

these attachments. Actual gross engine power will be higher than net engine power and

is affected by, among other things, ambient operating conditions and engine-to-engine

variability. Given the wide array of products on which engines are placed, the gasoline

engine may not develop the rated gross power when used in a given piece of power

equipment. This difference is due to a variety of factors including, but not limited to, the

variety of engine components (air cleaner, exhaust, charging, cooling, carburetor, fuel

pump, etc.), application limitations, ambient operating conditions (temperature, humidity,

altitude), and engine-to-engine variability. Due to manufacturing and capacity limitations,

Briggs & Stratton may substitute an engine of higher rated power for this engine.

Warranty

Briggs & Stratton Engine Warranty

Effective January 2019

Limited Warranty

Briggs & Stratton warrants that, during the warranty period specified below, it will repair

or replace, free of charge, any part that is defective in material or workmanship or

both. Transportation charges on product submitted for repair or replacement under this

warranty must be borne by purchaser. This warranty is effective for and is subject to

the time periods and conditions stated below. For warranty service, find the nearest

Authorized Service Dealer in our dealer locator map at BRIGGSandSTRATTON.COM.

The purchaser must contact the Authorized Service Dealer, and then make the product

available to the Authorized Service Dealer for inspection and testing.

There is no other express warranty. Implied warranties, including those of

merchantability and fitness for a particular purpose, are limited to the warranty

period listed below, or to the extent permitted by law. Liability for incidental or

consequential damages are excluded to the extent exclusion is permitted by law. Some

states or countries do not allow limitations on how long an implied warranty lasts,

and some states or countries do not allow the exclusion or limitation of incidental or

consequential damages, so the above limitation and exclusion may not apply to you.

This warranty gives you specific legal rights and you may also have other rights which

vary from state to state and country to country

Standard Warranty Terms

1, 2, 3

Vanguard®; Commercial Series

Consumer Use - 36 months

Commercial Use - 36 months

XR Series

Consumer Use - 24 months

Commercial Use - 24 months

All Other Engines Featuring Dura-Bore™ Cast Iron Sleeve

Consumer Use - 24 months

Commercial Use - 12 months

All Other Engines

Consumer Use - 24 months

Commercial Use - 3 months

These are our standard warranty terms, but occasionally there may be additional

warranty coverage that was not determined at time of publication. For a listing

of current warranty terms for your engine, go to BRIGGSandSTRATTON.com or

contact your Briggs & Stratton Authorized Service Dealer.

There is no warranty for engines on equipment used for prime power in place

of a utility; standby generators used for commercial purposes, utility vehicles

exceeding 25 MPH, or engines used in competitive racing or on commercial or

rental tracks.

Vanguard installed on standby generators: 24 months consumer use, no

warranty commercial use. Commercial Series with manufacturing date before July

2017: 24 months consumer use, 24 months commercial use.

In Australia - Our goods come with guarantees that cannot be excluded under

the Australian Consumer Law. You are entitled to a replacement or refund for a

major failure and for compensation for any other reasonably foreseeable loss or

damage. You are also entitled to have the goods repaired or replaced if the goods

fail to be of acceptable quality and the failure does not amount to a major failure.

For warranty service, find the nearest Authorized Service Dealer in our dealer

locator map at BRIGGSandSTRATTON.COM, or by calling 1300 274 447, or by

emailing or writing to [email protected], Briggs & Stratton

Australia Pty Ltd, 1 Moorebank Avenue, Moorebank, NSW , Australia, 2170.

The warranty period begins on the original date of purchase by the first retail or

commercial consumer. "Consumer use" means personal residential household use by a

retail consumer. "Commercial use" means all other uses, including use for commercial,

income producing or rental purposes. Once an engine has experienced commercial

use, it shall thereafter be considered as a commercial use engine for purposes of this

warranty.

Save your proof of purchase receipt. If you do not provide proof of the initial

purchase date at the time warranty service is requested, the manufacturing date

of the product will be used to determine the warranty period. Product registration

is not required to obtain warranty service on Briggs & Stratton products.

About Your Warranty

This limited warranty covers engine-related material and/or workmanship issues only,

and not replacement or refund of the equipment to which the engine may be mounted.

Routine maintenance, tune-ups, adjustments, or normal wear and tear are not covered

under this warranty. Similarly, warranty is not applicable if the engine has been altered

or modified or if the engine serial number has been defaced or removed. This warranty

does not cover engine damage or performance problems caused by:

1. The use of parts that are not original Briggs & Stratton parts;

2. Operating the engine with insufficient, contaminated, or an incorrect grade of

lubricating oil;

3. The use of contaminated or stale fuel, gasoline formulated with ethanol greater than

10%, or the use of alternative fuels such as liquefied petroleum or natural gas on

engines not originally designed/manufactured by Briggs & Stratton to operate on

such fuels;

4. Dirt which entered the engine because of improper air cleaner maintenance or re-

assembly;

5. Striking an object with the cutter blade of a rotary lawn mower, loose or improperly

installed blade adapters, impellers, or other crankshaft coupled devices, or

excessive v-belt tightness;

6. Associated parts or assemblies such as clutches, transmissions, equipment

controls, etc., which are not supplied by Briggs & Stratton;

7. Overheating due to grass clippings, dirt and debris, or rodent nests which plug or

clog the cooling fins or flywheel area, or by operating the engine without sufficient

ventilation;

8. Excessive vibration due to over-speeding, loose engine mounting, loose or

unbalanced cutter blades or impellers, or improper coupling of equipment

components to the crankshaft;

9. Misuse, lack of routine maintenance, shipping, handling, or warehousing of

equipment, or improper engine installation.

10 vanguardpower.com

Not for

Reproduction

Warranty service is available only through Briggs & Stratton Authorized Service

Dealers. Locate your nearest Authorized Service Dealer in our dealer locator map

at BRIGGSandSTRATTON.COM or by calling 1-800-233-3723 (in USA).

80004537 (Rev. F)

Briggs & Stratton Emissions Warranty

California, U.S. EPA, and Briggs & Stratton, LLC Emissions Control Warranty -

Your Warranty Rights and Obligations

For Briggs & Stratton Engine Models with "B" or "G" Trim Designation (Model-

Type-Trim Representation xxxxxx xxxx Bx or xxxxxx xxxx Gx)

The California Air Resources Board, U.S. EPA, and Briggs & Stratton (B&S) are

pleased to explain the exhaust emissions (“emissions”) control system warranty on

your 2020-2022 engine. In California, new small off-road engines and large spark

ignited engines less than or equal to 1.0 liter must be designed, built, and equipped

to meet the State’s stringent anti-smog standards. B&S must warrant the emissions

control system on your engine for the periods of time listed below provided there has

been no abuse, neglect or improper maintenance of your small off-road engine or

equipment leading to the failure of the emissions control system.

Your emissions control system may include parts such as the carburetor or fuel-

injection system, the ignition system, catalytic converter, fuel tanks, fuel lines (for liquid

fuel and fuel vapors), fuel caps, valves, canisters, filters, clamps and other associated

components. Also included may be hoses, belts, connectors, and other emission-

related assemblies.

Where a warrantable condition exists, B&S will repair your engine at no cost to you

including diagnosis, parts, and labor.

Manufacturer’s Warranty Coverage:

The exhaust emissions control system on your engine is warranted for two years.

If any emissions-related part on your engine is defective, the part will be repaired or

replaced by B&S.

Owner’s Warranty Responsibilities:

• As the engine owner, you are responsible for the performance of the required

maintenance listed in your owner’s manual. B&S recommends that you retain

all receipts covering maintenance on your engine, but B&S cannot deny

warranty coverage solely for the lack of receipts or for your failure to ensure the

performance of all scheduled maintenance.

• As the engine owner, you should however be aware that B&S may deny you

warranty coverage if your engine or a part has failed due to abuse, neglect, or

improper maintenance or unapproved modifications.

• You are responsible for presenting your engine to a B&S distribution center

or service center as soon as the problem exists. The warranty repairs shall

be completed in a reasonable amount of time, not to exceed 30 days. If you

have a question regarding your warranty rights and responsibilities, you should

contact B&S at 1-800-444-7774 (in USA) or BRIGGSandSTRATTON.COM.

Briggs & Stratton Emissions Control Warranty Provisions

The following are specific provisions relative to your Emissions Control Warranty

Coverage. It is in addition to the B&S engine warranty for non-regulated engines found

in the Operator’s Manual.

1. Warranted Emissions Parts

Coverage under this warranty extends only to the parts listed below (the emissions

control systems parts) to the extent these parts were present on the B&S engine.

a. Fuel Metering System

• Cold start enrichment system (soft choke)

• Carburetor or fuel injection system

• Oxygen sensor

• Electronic control unit

• Fuel pump module

b. Air Induction System

• Air cleaner

• Intake manifold

c. Ignition System

• Spark plug(s)

• Magneto ignition system

d. Catalyst System

• Catalytic converter

• Exhaust manifold

• Air injection system or pulse value

e. Miscellaneous Items Used in Above Systems

• Vacuum, temperature, position, time sensitive valves and switches

• Connectors and assemblies

• Electronic controls

2. Length of Coverage

Coverage is for a period of two years from the date of delivery to an ultimate

purchaser, or for the time period listed in the respective engine or product warranty

statement, whichever is greater. B&S warrants to the original purchaser and each

subsequent purchaser that the engine is designed, built, and equipped so as to

conform with all applicable regulations adopted by the Air Resources Board; that

it is free from defects in material and workmanship that could cause the failure

of a warranted part; and that it is identical in allmaterial respects to the engine

described in the manufacturer’s application for certification. The warranty period

begins on the date the engine or equipment is delivered to an ultimate purchaser.

The warranty on emissions-related parts is as follows:

• Any warranted part that is not scheduled for replacement as required

maintenance in the Operator’s Manual supplied, is warranted for the warranty

period stated above. If any such part fails during the period of warranty

coverage, the part will be repaired or replaced by B&S at no charge to

the owner. Any such part repaired or replaced under the warranty will be

warranted for the remaining warranty period.

• Any warranted part that is scheduled only for regular inspection in the

Operator’s Manual supplied, is warranted for the warranty period stated

above. Any such part repaired or replaced under warranty will be warranted

for the remaining warranty period.

• Any warranted part that is scheduled for replacement as required

maintenance in the Operators’s Manual supplied, is warranted for the period

of time prior to the first scheduled replacement point for that part. If the

part fails prior to the first scheduled replacement, the part will be repaired

or replaced by B&S at no charge to the owner. Any such part repaired or

replaced under warranty will be warranted for the remainder of the period

prior to the first scheduled replacement point for the part.

• Add-on or modified parts that are not exempted by the Air Resources Board

may not be used. The use of any non-exempted add-on or modified parts by

the owner will be grounds for disallowing a warranty claim. The manufacturer

will not be liable to warrant failures of warranted parts caused by the use of a

non-exempted add-on or modified part.

3. Consequential Coverage

Coverage shall extend to the failure of any engine components caused by the

failure of any warranted emissions parts.

4. Claims and Coverage Exclusions

Warranty claims shall be filed according to the provisions of the B&S engine

warranty policy. Warranty coverage does not apply to failures of emissions

parts that are not original equipment B&S parts or to parts that fail due to abuse,

neglect, or improper maintenance as set forth in the B&S engine warranty policy.

B&S is not liable for warranty coverage of failures of emissions parts caused by

the use of add-on or modified parts.

Look For Relevant Emissions Durability Period and Air Index Information On

Your Small Off-Road Engine Emissions Label

Engines that are certified to meet the California Air Resources Board (CARB) small off-

road Emissions Standard must display information regarding the Emissions Durability

Period and the Air Index. Briggs & Stratton makes this information available to the

consumer on our emissions labels. The engine emissions label will indicate certification

information.

The Emissions Durability Period describes the number of hours of actual running

time for which the engine is certified to be emissions compliant, assuming proper

maintenance in accordance with the Operator’s Manual. The following categories are

used:

Moderate:

Engines at or less than 80 cc displacement are certified to be emissions compliant for

50 hours of actual engine running time. Engines greater than 80 cc displacement are

certified to be emissions compliant for 125 hours of actual engine running time.

Intermediate:

Engines at or less than 80 cc displacement are certified to be emissions compliant for

125 hours of actual engine running time. Engines greater than 80 cc displacement are

certified to be emissions compliant for 250 hours of actual engine running time.

Extended:

Engines at or less than 80 cc displacement are certified to be emissions compliant for

300 hours of actual engine running time. Engines greater than 80 cc displacement are

certified to be emissions compliant for 500 hours of actual engine running time.

For example, a typical walk-behind lawn mower is used 20 to 25 hours per year.

Therefore, the Emissions Durability Period of an engine with an intermediate rating

would equate to 10 to 12 years.

Briggs & Stratton engines are certified to meet the United States Environmental

Protection Agency (USEPA) Phase 2 or Phase 3 emissions standards. The Emissions

Compliance Period referred to on the Emissions Compliance label indicates the

number of operating hours for which the engine has been shown to meet Federal

emissions requirements.

Not for

Reproduction

For engines at or less than 80 cc displacement:

Category C = 50 hours, Category B = 125 hours, Category A = 300 hours

For engines greater than 80 cc displacement and less than 225 cc displacement:

Category C = 125 hours, Category B = 250 hours, Category A = 500 hours

For engines of 225 cc or more displacement:

Category C = 250 hours, Category B = 500 hours, Category A = 1000 hours

80099153(Revision A)

Briggs & Stratton Emissions Warranty

U.S. EPA, and Briggs & Stratton, LLC Emissions Control Warranty Statement -

Your Warranty Rights and Obligations

For Briggs & Stratton Engine Models with "J" Trim Designation (Model-Type-

Trim Representation xxxxxx xxxx Jx)

The U.S. EPA, and Briggs & Stratton (B&S) are pleased to explain the exhaust

emissions control system warranty on your Model Year 2020-2022 engine. In the U.S,

new small off-road engines and large spark ignited engines less than or equal to 1.0

liter must be designed, built, and equipped to meet stringent anti-smog standards. B&S

must warrant the emissions control system on your engine for the periods of time listed

below provided there has been no abuse, neglect, or improper maintenance of your

engine leading to the failure of the emissions control system.

Your emissions control system may include parts such as the carburetor or fuel-

injection system, the ignition system, catalytic converter, fuel tanks, fuel lines (for liquid

fuel and fuel vapors), fuel caps, valves, canisters, filters, clamps and other associated

components. Also included may be hoses, belts, connectors, and other emission-

related assemblies.

Where a warrantable condition exists, B&S will repair your engine at no cost to you

including diagnosis, parts, and labor.

Manufacturer’s Warranty Coverage:

The exhaust emissions control system on your engine is warranted for two years. If

any emissions-related parts on your engine is defective, the part will be repaired of

replaced by B&S.

Owner’s Warranty Responsibilities:

• As the engine owner, you are responsible for the performance of the required

maintenance listed in your Operator’s Manual. B&S recommends that you

retain all receipts covering maintenance on your engine, but B&S cannot deny

warranty coverage solely for the lack of receipts or your failure to ensure the

performance of all scheduled maintenance.

• As the engine owner, you should however be aware that B&S may deny you

warranty coverage if your engine or a part has failed due to abuse, neglect,

improper maintenance, or unapproved modifications.

• You are responsible for presenting your engine to a B&S distribution center,

or service center, as soon as a problem exists. The warranty repairs should

be completed in a reasonable amount of time, not to exceed 30 days. If you

have a question regarding your warranty rights and responsibilities, you should

contact B&S at 1-800-444-7774 (in USA) or BRIGGSandSTRATTON.com.

Briggs & Stratton Emissions Control Warranty Provisions

The following are specific provisions relative to your Emissions Control Warranty

Coverage. It is in addition to the B&S engine warranty for non-regulated engines found

in the Operator’s Manual.

1. Warranted Emissions Parts

Coverage under this warranty extends only to the parts listed below (the emissions

control systems parts) to the extent these parts were present on the B&S engine.

a. Fuel Metering System

• Cold start enrichment system (soft choke)

• Carburetor or fuel injection system

• Oxygen sensor

• Electronic control unit

• Fuel pump module

b. Air Induction System

• Air cleaner

• Intake manifold

c. Ignition System

• Spark plug(s)

• Magneto ignition system

d. Catalyst System

• Catalytic converter

• Exhaust manifold

• Air injection system or pulse value

e. Miscellaneous Items Used in Above Systems

• Vacuum, temperature, position, time sensitive valves and switches

• Connectors and assemblies

• Electronic controls

2. Length of Coverage

Coverage is for a period of two years from the date of delivery to an ultimate

purchaser, or for the period listed in the respective engine or product warranty

statement, whichever is greater. B&S warrants to the original purchaser and each

subsequent purchaser that the engine is designed, built, and equipped so as to

conform with all applicable regulations under Section 213 of the Clean Air Act that

is free from defects in material and workmanshipthat could cause the failure of a

warranted part; and that is identical in all material respects to the engine described

in the manufacturer’s application for certification. The warranty period begins on

the date the engine or equipment is delivered to an ultimate purchaser.

The warranty on emissions-related parts is as follows:

• Any warranted part that is not scheduled for replacement as required

maintenance in the Operator’s Manual supplied, is warranted for the warranty

period stated above. If any such part fails during the period of warranty

coverage, the part will be repaired or replaced by B&S at no charge to

the owner. Any such part repaired or replaced under the warranty will be

warranted for the remaining warranty period.

• Any warranted part that is scheduled only for regular inspection in the

Operator’s Manual supplied, is warranted for the warranty period stated

above. Any such part repaired or replaced under warranty will be warranted

for the remaining warranty period.

• Any warranted part that is scheduled for replacement as required

maintenance in the Operator's Manual supplied, is warranted for the period of

time prior to the first scheduled replacement point for that part. If the part fails

prior to the first scheduled replacement, the part will be repaired or replaced

by B&S at no charge to the owner. Any such part repaired or replaced under

warranty will be warranted for the remainder of the period prior to the first

scheduled replacement point for the part.

• Add-on or modified parts that are not exempted by the U.S. EPA may not be

used. The use of any non-exempted add-on or modified parts by the owner

will be grounds for disallowing a warranty claim. The manufacturer will not

be liable to warrant failures of warranted parts caused by the use of a non-

exempted add-on or modified part.

3. Consequential Coverage

Coverage shall extend to the failure of any engine components caused by the

failure of any warranted emissions parts.

4. Claims and Coverage Exclusions

Warranty claims shall be filed according to the provisions of the B&S engine

warranty policy. Warranty coverage does not apply to failures of emissions

parts that are not original equipment B&S parts or to parts that fail due to abuse,

neglect, or improper maintenance as set forth in the B&S engine warranty policy.

B&S is not liable for warranty coverage of failures of emissions parts caused by

the use of add-on or modified parts.

Look For Relevant Emissions Durability Period and Air Index Information On

Your Small Off-Road Engine Emissions Label

Briggs & Stratton engines are certified to meet the United States Environmental

Protection Agency (USEPA) Phase 3 emissions standards. The Emissions Compliance

Period referred to on the Emissions Compliance label indicates the number of

operating hours for which the engine has been shown to meet Federal emissions

requirements.

For engines at or less than 80 cc displacement:

Category C = 50 hours, Category B = 125 hours, Category A = 300 hours

For engines greater than 80 cc displacement and less than 225 cc displacement:

Category C = 125 hours, Category B = 250 hours, Category A = 500 hours

For engines of 225 cc or more displacement:

Category C = 250 hours, Category B = 500 hours, Category A = 1000 hours

80099149 (Revision A)

12 vanguardpower.com

Not for

Reproduction

Generel information

Denne vejledning indeholder sikkerhedsoplysninger, der skal gøre dig opmærksom

på farer og risici i forbindelse med denne motor, og hvordan du forhindrer dem. Den

indeholder også instruktioner til korrekt brug og vedligeholdelse af motoren. Eftersom

Briggs & Stratton ikke ved, hvilket udstyr denne motor skal drive, er det vigtigt, at

du læser, forstår og følger disse instruktioner. Gem disse originale anvisninger til

fremtidig brug.

BEMÆRK:Figurerne og illustrationerne i denne vejledning er udelukkende til

referencebrug og kan være anderledes end din model. Hvis du har brug for hjælp,

kontakt en autoriseret serviceforhandler.

For at kunne få reservedele eller teknisk assistance skal du registrere købsdatoen samt

motorens model-, type-, trim- og serienummer. Disse numre er placeret på din motor. Se

afsnittet Funktioner og betjeningsanordninger.

Købsdato

Motormodel- Type- Trim

Motorserienummer

Kontaktoplysninger for europæisk kontor

For spørgsmål vedrørende europæisk emission bedes du kontakte vores europæiske

kontor på:

Max-Born-Straße 2, 68519 Viernheim, Tyskland.

Europæiske Union (EU) Trin V (5):

Kuldioxid-værdier (CO2)

Indtast CO2 i søgevinduet på BriggsandStratton.com for at finde kuldioxid-værdier for

Briggs & Stratton EU-typegodkendelsescertifikat for motorer.

Information om genbrug

Genbrug alle kartoner, æsker, brugt olie og batterier i

henhold til de gældende regeringsbestemmelser.

Førersikkerhed

Sikkerhedssymboler og signalord

Sikkerhedsadvarselssymbolet identificerer sikkerhedsoplysninger om farer,

der kan medføre personskader. Et signalord (FARE, ADVARSEL eller FORSIGTIG)

bliver brugt for at illustrere sandsynligheden for og den mulige grad af personskade.

Desuden bruges et faresymbol til at illustrere faretypen.

FARE indikerer en fare, som, hvis den ikke undgås, vil forårsage dødsfald eller alvorlig

personskade.

ADVARSEL indikerer en fare, som, hvis den ikke undgås, kan forårsage dødsfald eller

alvorlig personskade.

FORSIGTIG indikerer en farlig situation, som, hvis den ikke undgås, kan medføre

alvorlig eller moderat personskade.

BEMÆRK angiver oplysninger, der anses som vigtige, men som ikke vedrører farer.

Faresymboler og deres betydninger

Sikkerhedsinformation om

farer, som kan resultere i

personskade.

Læs og forstå

brugervejledningen før

brug af eller servicering af

enheden.

Brandfare Eksplosionsfare

Fare for stød Fare for giftige dampe

Fare fra varm overflade Støjfare - Høreværn

anbefales ved brug i

længere tid.

Fare for flyvende

genstande - Bær

beskyttelsesbriller.

Eksplosionsfare

Fare for forfrysning Fare for tilbageslag

Fare for amputation -

Bevægelige dele

Kemikaliefare

Fare for varme Ætsende fare

Sikkerhedsmeddelelser

ADVARSEL

Briggs & Stratton®-motorer er ikke designet til og må ikke bruges til at drive: fun-karts;

go-karts; terrængående børne-, fridtids- eller sportskøretøjer (ATV’er); motorcykler,

hovercraft; luftfartsprodukter eller køretøjer, der anvendes til konkurrenceformål, som

ikke er sanktioneret af Briggs & Stratton. For yderligere oplysninger om racingprodukter

se www.briggsracing.com. For brug med terrængående og side-by-side ATV’er kontakt

Briggs & Stratton Power Application Center, 1-866-927-3349. Forkert motorbrug kan

medføre alvorlig personskade eller dødsfald.

ADVARSEL

Benzin og benzindampe er brændbare og eksplosive. Brand eller eksplosion kan

medføre forbrændinger eller dødsfald.

Når du påfylder brændstof

• Stop motoren. Inden du fjerner brændstofdækslet, skal du vente mindst to (2)

minutter for at sikre dig, at motoren er nedkølet.

• Fyld brændstoftanken udendørs eller i et område med god luftgennemstrømning.

• Påfyld ikke for meget brændstof i tanken. Fyld ikke over bunden af

brændstoftankens hals, så der er plads til at brændstoffet kan udvide sig.

• Hold benzin væk fra gnister, åben ild, tændflammer, varme eller andre

antændelseskilder.

• Undersøg ofte brændstofledninger, brændstoftank, brændstofdæksel og

tilslutninger for revner eller lækager. Udskift beskadigede dele.

• Hvis der spildes brændstof, skal du vente, indtil det tørrer, inden du starter

motoren.

Når du starter motoren

• Sørg for, at tændrør, lyddæmper, brændstofdæksel og luftfilter (hvis monteret) er

monteret korrekt.

• Prøv ikke at starte motoren med tændrøret fjernet.

• Hvis motoren er oversvømmet, skal du indstille chokeren (hvis monteret) til

positionen ÅBEN eller KØR. Flyt gashåndtaget (hvis monteret) til positionen

HURTIG, og drej, indtil motoren starter.

• Hvis der er en utæthed af natur- eller LP-gas, må motoren ikke startes.

• Da dampe er brandfarlige, må du ikke bruge startvæsker under tryk.

Når du betjener udstyret

• Vip ikke motoren eller enheden, så brændstoffet løber ud.

• Brug ikke chokeren (hvis monteret) til at stoppe motoren.

• Start, eller betjen ikke motoren, når luftfilterenheden (hvis monteret) eller

luftfilteret (hvis monteret) er fjernet.

Når du udfører vedligeholdelse

• Hvis du tømmer olien fra oliepåfyldningsrøret i toppen, skal brændstoftanken

være tom. Hvis den ikke er tom, kan der forekomme brændstoflækage, og dette

kan medføre brand eller eksplosion.

• Under vedligeholdelse, hvis det er nødvendigt at vippe enheden, skal du

sørge for, at brændstoftanken, hvis monteret på motoren, er tom, og at

tændrørssiden vender opad. Hvis brændstoftanken ikke er tom, kan der

forekomme brændstoflækage, og dette kan medføre brand eller eksplosion.

• Undersøg ofte brændstofledninger, brændstoftank, brændstofdæksel og

tilslutninger for revner eller lækager. Udskift beskadigede dele.

Not for

Reproduction

• Udskift ikke regulatorfjederen, forbindelser eller andre dele for at øge motorens

hastighed.

• Undlad at slå på svinghjulet med en hammer eller hård genstand. Dette kan

medføre svigt i svinghjulet under drift.

• Reservedelene skal have samme udformning, og de skal placeres på præcist

samme måde som de originale dele. Andre dele kan medføre skade eller

personskade.

Når du flytter udstyrets placering

• Sørg for, at brændstoftanken er TOM, eller at brændstofhanen er i LUKKET-

stilling.

Når brændstof eller udstyr opbevares med brændstof i brændstoftanken

• Da en tændflamme eller andre antændelseskilder kan forårsage eksplosioner,

skal du holde brændstof eller udstyr på afstand af fyr, ovne, vandvarmere eller

andre enheder, der har en tændflamme.

ADVARSEL

Benzin og benzindampe er brændbare og eksplosive. Brand eller eksplosion kan

medføre forbrændinger eller dødsfald.

Motorstart medfører gnister, der kan medføre brand eller eksplosion.

• Hvis der er en utæthed af natur- eller LP-gas, må motoren ikke startes.

• Da dampe er brandfarlige, må du ikke bruge startvæsker under tryk.

ADVARSEL

FARE FOR GIFTIGE GASSER. Motorudstødning indeholder kulilte, som

er en giftig gas, der kan dræbe på få minutter. Selvom du ikke kan lugte

udstødningsgasser, kan du stadigvæk være udsat for kulilteforgiftning. Hvis du

får kvalme, føler dig svimmel eller svag, mens du bruger dette produkt, skal du

have frisk luft MED DET SAMME. Søg lægehjælp. Du kan være blevet udsat for

kulilteforgiftning.

• Kulilte kan opsamles i brugte områder. For at mindske risikoen for kuliltegas

skal du KUN bruge dette produkt udendørs og langt væk fra vinduer, døre og

åbninger.

• Installer batteridrevne kuliltealarmer eller strømtilsluttede alarmer med

batterisupport som specificeret i producentens instruktioner. Røgalarmer kan

ikke fornemme kulilte.

• Du MÅ IKKE betjene dette produkt indendørs i hjem, garager, kældre,

krybekældre, skure eller på andre indelukkede steder, også selvom du bruger

ventilatorer eller har åbne døre og vinduer for at sikre ordentlig ventilation. Efter

brug af dette produkt kan kulilte hurtigt samles i disse områder og forblive der i

flere timer.

• Anbring ALTID dette produkt i vindretningen, og sørg for, at udstødningen peger

væk fra steder, hvor der er folk til stede.

ADVARSEL

Hurtig tilbagetrækning af startsnoren (tilbageslag) vil bevirke, at din hånd og arm

bliver trukket hurtigere mod motoren, end du kan kontrollere.Konsekvenserne

kan være brækkede knogler, skrammer eller forstuvninger.

• For at forhindre tilbageslag når du starter motoren, så træk langsomt i

startsnoren, indtil der mærkes modstand, og træk så kraftigt i den.

• Inden du starter motoren, skal du frakoble eller fjerne alt eksternt udstyr og

motorbelastninger.

• Sørg for, at direkte tilkoblede dele på udstyret, såsom, men ikke begrænset til,

skæreknive, skovlhjul, remskiver, kædehjul, er korrekt monteret.

ADVARSEL

Roterende dele kan gribe fat i hænder, fødder, hår, tøj eller tilbehør og resultere i

traumatisk amputation eller flænger.

• Betjen udstyr med sikkerhedsafskærmningerne monteret korrekt.

• Hold hænder og fødder i sikker afstand fra roterende dele.

• Fjern smykker, og sørg for, at langt hår er sat op og væk fra alle roterende dele.

• Bær ikke løstsiddende tøj eller genstande, som kan blive fanget.

ADVARSEL

Under drift bliver motoren og lyddæmperen varm. Hvis du rører ved en varm

motor, kan der opstå termiske forbrændinger.

Brændbart materiale, såsom blade, græs og krat, kan blive antændt.

• Før du berører motoren eller lyddæmperen, skal du stoppe motoren og vente to

(2) minutter. Sørg for, at motoren og lyddæmperen er sikre at røre ved.

• Fjern affald fra lyddæmperen og motoren.

Det er en overtrædelse af staten Californiens forskrifter om offentlige ressourcer, afsnit

4442, at bruge eller betjene motoren på ethvert skov-, krat- eller græsdækket område,

medmindre udstødningssystemet er forsynet med en korrekt vedligeholdt gnistfanger

som beskrevet i afsnit 4442. Andre stater eller statsretskredse har eventuelt lignende

love, se statsforskrift 36 CFR, afsnit 261.52. Kontakt en autoriseret fabrikant eller

serviceforhandler angående anskaffelse af en gnistfanger, der er konstrueret til det

udstødningssystem, der er monteret på den pågældende maskine.

ADVARSEL

Tilfældige gnister fra motoren kan forårsage elektrisk stød eller brand og kan

medføre indfiltring, traumatisk amputation eller flænger.

Før du foretager justeringer eller reparationer:

• Fjern tændrørskablet, og hold det på behørig afstand af tændrøret.

• Frakobl batterikablet fra den negative terminal (gælder kun motorer med

elektrisk start).

• Brug kun passende værktøj.

Når du tjekker for gnister:

• Brug en godkendt tændrørstester.

• Test ikke for gnister med tændrøret fjernet.

ADVARSEL

Benzindampe er brændbare og eksplosive. Brand eller eksplosion kan medføre

forbrændinger eller dødsfald.

Hvis du kan lugte gas

• Start ikke motoren.

• Tænd ikke for elektriske kontakter.

• Brug ikke en telefon i nærheden.

• Evakuer området.

• Kontakt gasforsyningen eller alarmcentralen.

Funktioner og betjeningsanordninger

Motorens betjeningselementer

Sammenlign henvisningsbogstaverne i figur 1, 2, 3, og 4 med motorens

betjeningsanordninger på den følgende liste:

A. Motorens identifikationsnumre Model-, type- og kodenummer

B. Tændrør

C. Cyklonisk luftfilter

D. Luftfilter med lav profil

E. Oliepind

F. Oliepåfyldning

G. Oliefilter

H. Olieaftapningsprop

I. Olietrykføler

J. Fingerværn

K. Elektrisk starter

L. Startrelæ

M. Regulator / ensretter

N. Karburator - Karburatormodeller

O. Oliekøler (hvis monteret)

P. Lyddæmper (hvis monteret)

Q. Brændstofpumpe

Starterkontakt

Gasregulator

Chokerregulator(karburatormodeller

)

U. Brændstoffilter

V. Omdrejningstæller (hvis udstyret)

Nogle motorer og noget udstyr har fjernbetjeningsanordninger. Se udstyrsmanualen for

placering og betjening af fjernbetjeningsanordninger.

Motorfaresymboler og deres betydninger

Motorhastighed - HURTIG Motorhastighed -

LANGSOM

14 vanguardpower.com

Not for

Reproduction

Motorhastighed - STOP TÆND - SLUK

Motorstart

Choker LUKKET

Motorstart

Choker ÅBEN

Brændstofdæksel

Brændstofhane ÅBEN

Brændstofhane LUKKET

Brændstofniveau - Maks.

Undgå at overfylde

Betjening

Olieanbefalinger

Oliekapacitet: Se afsnittetSpecifikationer.

BEMÆRK

Denne motor blev leveret af Briggs & Stratton uden olie. Producenter eller forhandlere

af udstyret kan have fyldt olie på motoren. Inden du starter motoren første gang, skal

du sørge for, at olien er ved det rigtige niveau. Tilsæt olie som angivet i instruktionerne i

denne vejledning. Hvis du starter motoren uden olie, vil den blive beskadiget og vil ikke

blive repareret under garantien.

Vi anbefaler at bruge olie, der er certificeret af Briggs & Stratton

for at opnå den bedste

ydeevne. Andre selvrensende olier af høj kvalitet er tilladt, hvis de er godkendt til SF-,

SG-, SH-, SJ-service eller højere. Undlad at bruge specielle tilsætningsstoffer.

Brug skemaet til at vælge den bedste viskositet til det forventede

udendørstemperaturinterval. Motorer i det meste udstyr til udendørs brug kører

godt med syntetisk olie 5W-30. Til udstyr, der bruges i varmere temperaturer, yder

Vanguard

15W-50 syntetisk olie den bedste beskyttelse.

A SAE30- Under 40°F (4°C) vil brugen af SAE30 gøre det svært at starte.

B 10W-30- Over 80°F (27°C) kan brugen af 10W-30 medføre forhøjet

olieforbrug. Kontroller olieniveauet ofte.

C 5W-30

D Syntetisk 5W-30

Vanguard

syntetisk 15W-50

Kontrollér og påfyld olie

Før du tjekker eller påfylder olie

• Kontrollér, at motoren står plant.

• Rengør oliepåfyldningsområdet for affald.

• Se afsnittet Specifikationer mht. oliekapacitet.

BEMÆRK

Denne motor blev leveret af Briggs & Stratton uden olie. Producenter eller forhandlere

af udstyret kan have fyldt olie på motoren. Inden du starter motoren første gang, skal

du sørge for, at olien er ved det rigtige niveau. Tilsæt olie som angivet i instruktionerne i

denne vejledning. Hvis du starter motoren uden olie, vil den blive beskadiget og vil ikke

blive repareret under garantien.

1. Tag oliepinden ud (A, figur 5), og rengør den med en klud.

2. Sæt oliepinden i, og spænd den (A, figur 5).

3. Træk oliepinden op, og kontrollér oliestanden. Sørg for, at olieniveauet når op til

toppen af fuld-mærket (B, figur 5) på oliepinden.

4. Hvis oliestanden er for lav, skal du langsomt påfylde olie i motoroliepåfyldningen

(C, figur 5). Hæld ikke for meget olie på. Vent et minut efter oliepåfyldning, og

kontrollér oliestanden igen. Sørg for, at olieniveauet er korrekt.

5. Sæt oliepinden i, og spænd den (A, figur 5).

Beskyttelsessystem for lav oliestand (hvis

monteret)

Der er monteret en sensor for lav oliestand på nogle motorer. Hvis oliestanden er lav,

viser sensoren enten et advarselslys eller standser motoren. Stop motoren, og følg

disse trin, før du starter motoren.

• Kontrollér, at motoren står plant.

• Foretag en oliekontrol. Se afsnittet Kontrollér oliestand.

• Hvis oliestanden er lav, så tilføj den korrekte mængde olie. Start motoren, og

sørg for, at advarselslyset (hvis monteret) ikke tændes.

• Hvis oliestanden ikke er lav, må du ikke starte motoren. Kontakt en autoriseret

serviceforhandler fra Briggs & Stratton for at få rettet olieproblemet.

Anbefalet brændstof

Brændstoffet skal overholde følgende krav:

• Ren, frisk blyfri benzin.

• Mindst 87 oktan/87 AKI (91 RON). Skal kunne anvendes i højder; se nedenfor.

• Benzin med op til 10% ætanol (gasohol) er tilladt.

BEMÆRK

Brug ikke ikke-godkendt benzin, såsom E15 og E85. Der må ikke blandes olie i

benzin, og der må ikke foretages ændringer på motoren, så den fungerer med

alternative brændstoffer. Brug af ikke-godkendt brændstof resulterer i skader på

motorkomponenterne, som ikke bliver repareret under garantien.

For at beskytte brændstofsystemet mod dannelse af gummi, kan brændstoffer tilsættes

en stabilisator. Se afsnittet Opbevaring. Brændstoffer er forskellige. Hvis du oplever

start- eller driftsproblemer, så skift brændstofleverandør eller -mærke. Motoren er

godkendt til at køre på benzin. Emissionskontrolsystemet for motorer med karburator

er EM (motormodifikationer). Emissionskontrolsystemet for motorer med elektronisk

brændstofindsprøjtning er ECM (motorstyringsmodul), MPI (flerportsinjektion) og hvis

udrustet dermed en O2S (iltsensor).

Højder

Ved højder over 1.524 m (5.000fod) er benzin med 85 oktan/85 AKI (89 RON) tilladt.

På motorer med karburator skal der foretages højdetilpasning for at vedligeholde

ydeevnen. Drift uden disse justeringer vil medføre en nedgang i ydelse, en stigning

i brændstofforbrug og øgede emissioner. Kontakt en Briggs & Stratton autoriseret

forhandler for oplysninger om højdejusteringer. Drift af en motor, der er justeret til store

højder, kan ikke anbefales i højder under 2.500 fod (762 m).

På motorer med elektronisk brændstofindsprøjtning (EFI) er det ikke nødvendigt at

foretage justering til brug i højtliggende områder.

Påfyld brændstof

ADVARSEL

Benzin og benzindampe er brændbare og eksplosive. Brand eller eksplosion kan

medføre forbrændinger eller dødsfald.

Når du påfylder brændstof

• Stop motoren. Inden du fjerner brændstofdækslet, skal du vente mindst to (2)

minutter for at sikre dig, at motoren er nedkølet.

• Fyld brændstoftanken udendørs eller i et område med god luftgennemstrømning.

• Påfyld ikke for meget brændstof i tanken. Fyld ikke over bunden af

brændstoftankens hals, så der er plads til at brændstoffet kan udvide sig.

• Hold benzin væk fra gnister, åben ild, tændflammer, varme eller andre

antændelseskilder.

• Undersøg ofte brændstofledninger, brændstoftank, brændstofdæksel og

tilslutninger for revner eller lækager. Udskift beskadigede dele.

• Hvis der spildes brændstof, skal du vente, indtil det tørrer, inden du starter

motoren.

1. Rengør brændstofdækslet for snavs og affaldsrester. Fjern brændstofsdækslet.

2. Fyld brændstoftanken (A, figur 6) med brændstof. Da brændstof udvides, skal du

undlade at fylde op over bunden af brændstoftankens hals (B).

3. Sæt dækslet tilbage på plads.

Not for

Reproduction

Start og stop motoren

Start motoren

ADVARSEL

Hurtig tilbagetrækning af startsnoren (tilbageslag) vil bevirke, at din hånd og arm

bliver trukket hurtigere mod motoren, end du kan kontrollere.Konsekvenserne

kan være brækkede knogler, skrammer eller forstuvninger.

• For at forhindre tilbageslag når du starter motoren, så træk langsomt i

startsnoren, indtil der mærkes modstand, og træk så kraftigt i den.

• Inden du starter motoren, skal du frakoble eller fjerne alt eksternt udstyr og

motorbelastninger.

• Sørg for, at direkte tilkoblede dele på udstyret, såsom, men ikke begrænset til,

skæreknive, skovlhjul, remskiver, kædehjul, er korrekt monteret.

ADVARSEL

Benzin og benzindampe er brændbare og eksplosive. Brand eller eksplosion kan

medføre forbrændinger eller dødsfald.

Når du starter motoren

• Sørg for, at tændrør, lyddæmper, brændstofdæksel og luftfilter (hvis monteret)

er monteret korrekt.

• Prøv ikke at starte motoren med tændrøret fjernet.

• Hvis motoren er oversvømmet, skal du indstille chokeren (hvis monteret) til

positionen ÅBEN eller KØR. Flyt gashåndtaget (hvis monteret) til positionen

HURTIG, og drej, indtil motoren starter.

• Hvis der er en utæthed af natur- eller LP-gas, må motoren ikke startes.

• Da dampe er brandfarlige, må du ikke bruge startvæsker under tryk.

ADVARSEL

FARE FOR GIFTIGE GASSER. Motorudstødning indeholder kulilte, som

er en giftig gas, der kan dræbe på få minutter. Selvom du ikke kan lugte

udstødningsgasser, kan du stadigvæk være udsat for kulilteforgiftning. Hvis du

får kvalme, føler dig svimmel eller svag, mens du bruger dette produkt, skal du

have frisk luft MED DET SAMME. Søg lægehjælp. Du kan være blevet udsat for

kulilteforgiftning.

• Kulilte kan opsamles i brugte områder. For at mindske risikoen for kuliltegas

skal du KUN bruge dette produkt udendørs og langt væk fra vinduer, døre og

åbninger.

• Installer batteridrevne kuliltealarmer eller strømtilsluttede alarmer med

batterisupport som specificeret i producentens instruktioner. Røgalarmer kan

ikke fornemme kulilte.

• Du MÅ IKKE betjene dette produkt indendørs i hjem, garager, kældre,

krybekældre, skure eller på andre indelukkede steder, også selvom du bruger

ventilatorer eller har åbne døre og vinduer for at sikre ordentlig ventilation. Efter

brug af dette produkt kan kulilte hurtigt samles i disse områder og forblive der i

flere timer.

• Anbring ALTID dette produkt i vindretningen, og sørg for, at udstødningen

peger væk fra steder, hvor der er folk til stede.

BEMÆRK

Denne motor blev leveret af Briggs & Stratton uden olie. Producenter eller forhandlere

af udstyret kan have fyldt olie på motoren. Inden du starter motoren første gang, skal

du sørge for, at olien er ved det rigtige niveau. Tilsæt olie som angivet i instruktionerne

i denne vejledning. Hvis du starter motoren uden olie, vil den blive beskadiget og vil

ikke blive repareret under garantien.

Typer af startsystemer

Før du starter motoren, skal du identificere typen af startsystem på din motor. Din

motor vil have en af disse typer.

• Elektronisk brændstofindsprøjtning (EFI): Et EFI-system har ikke en choker

eller en primer.

• Chokersystem: Denne type system har en choker, der skal bruges i kølige

temperaturer. Nogle modeller har en separat chokerregulering, mens andre har

en kombination af choker- og gasregulering. Den har ikke en primerfunktion.

BEMÆRK:Dit udstyr kan have fjernbetjeninger. Se udstyrsmanualen for placering og

betjening af fjernbetjeningen.

Elektronisk brændstofindsprøjtning (EFI)

1. Kontroller motorolien. Se afsnittetKontrol af olieniveau.

2. Sørg for, at udstyrets kørselsbetjeningsanordninger, hvis monteret, er frakoblet.

3. Sæt brændstofhanen (A, figur 7) i positionen ÅBEN, hvis monteret.

4. Sæt gasregulatoren (B, figur 7), hvis monteret, i stillingen HURTIG. Betjen motoren

i positionen HURTIG.

5. Drej den elektriske startkontakt (D, figur 7) til stillingen TIL eller START.

BEMÆRKStarterens levetid kan forlænges ved at bruge korte startcyklusser (maks.

fem sekunder). Vent ét minut mellem startcyklusserne.

Hvis motoren ikke starter efter 3 eller 4 forsøg, skal du kontakte din lokale forhandler,

gå til vanguardpower.com eller ringe til 1-800-999-9333.

Chokersystem

1. Kontroller motorolien. Se afsnittetKontrol af olieniveau.

2. Sørg for, at udstyrets kørselsbetjeningsanordninger, hvis monteret, er frakoblet.

3. Sæt brændstofhanen (A, figur 7) i positionen ÅBEN, hvis monteret.

4. Sæt gasregulatoren (B, figur 7), hvis monteret, i stillingen HURTIG. Betjen motoren

i positionen HURTIG.

5. Flyt chokerregulatoren (C, figur 7) eller kombinationen af choker og gas (B, C) til

stillingen LUKKET.

BEMÆRK:For at starte motoren med et tørlagt brændstofsystem er der behov

for ekstra starttid i chokerpositionen. Det giver brændstofpumpen tid til at fylde

brændstofsystemet op.

6. Drej tændingskontakten (D, figur 7) til stillingen TIL eller START.

7. Hvis motoren starter men ikke kan fortsætte med at køre, skal du flytte

chokerregulatoren (C, figur7) til stillingen ÅBEN for at starte motoren.

BEMÆRKStarterens levetid kan forlænges ved at bruge korte startcyklusser (maks.

fem sekunder). Vent ét minut mellem startcyklusserne.

8. Når motoren bliver varm, skal du flytte chokerregulatoren (C, figur 7) til stillingen

ÅBEN.

Hvis motoren ikke starter efter 3 eller 4 forsøg, skal du kontakte din lokale forhandler,

gå til vanguardpower.com eller ringe til 1-800-999-9333.

Stop motoren

ADVARSEL

Benzin og benzindampe er brændbare og eksplosive. Brand eller eksplosion kan

medføre forbrændinger eller dødsfald.

• Brug ikke chokeren (hvis monteret) til at stoppe motoren.

1. Med gasregulatoren i stillingen LANGSOM, drej den elektriske startkontakt (D,

figur7) til stillingen FRA. Tag nøglen ud, og opbevar den på et sikkert sted uden for

børns rækkevidde.

2. Efter at motoren er standset, drej brændstofhanen (A, figur 7) til positionen

LUKKET, hvis monteret.

Vedligeholdelse

Vedligeholdelsesoplysninger

ADVARSEL

Under vedligeholdelse, hvis det er nødvendigt at vippe enheden, skal du sørge for, at

brændstoftanken, hvis monteret på motoren, er tom, og at tændrørssiden vender opad.

Hvis brændstoftanken ikke er tom, kan der forekomme brændstoflækage, og dette kan

medføre brand eller eksplosion. Hvis motoren vippes i en anden retning, starter den ikke

nemt på grund af olie- eller brændstofforurening af luftfilteret eller tændrøret.

Vi anbefaler, at du kontakter en autoriseret serviceforhandler fra Briggs & Stratton

vedrørende al vedligeholdelse og eftersyn af motoren og motordele.

BEMÆRK

Alle komponenter, der bruges til at bygge dette produkt, skal forblive på plads for korrekt

drift.

ADVARSEL

Tilfældige gnister fra motoren kan forårsage elektrisk stød eller brand og kan

medføre indfiltring, traumatisk amputation eller flænger.

Før du foretager justeringer eller reparationer:

• Fjern tændrørskablet, og hold det på behørig afstand af tændrøret.

• Frakobl batterikablet fra den negative terminal (gælder kun motorer med

elektrisk start).

• Brug kun passende værktøj.

Når du tjekker for gnister:

• Brug en godkendt tændrørstester.

• Test ikke for gnister med tændrøret fjernet.

16 vanguardpower.com

Not for

Reproduction

Udførelse af udledningskontrol

Ved vedligeholdelse, udskiftning eller reparation af udledningskontrolenheder

og systemer, skal du kontakte et kvalificeret offroad-motorværksted eller

en servicetekniker. For at få udført udledningskontrolservice “uden beregning”

skal arbejdet imidlertid udføres af en autoriseret forhandler. Se erklæringer om

udledningskontrol.

Vedligeholdelsesskema

8-timers intervaller eller dagligt

• Kontroller oliestanden i motoren.

• Rengør området omkring lyddæmperen og betjeningsanordningerne.

100 timers intervaller eller årligt

•

Rengør eller udskift luftfilteret

1, 2

• Udskift motorolien og filteret.

• Udskift oliefilteret (hvis monteret).

• Udskift tændrørene.

• Tjek lyddæmper og gnistfanger.

• Servicér udstødningssystemet.

250 timers intervaller eller årligt

• Tjek ventilfrirummet. Juster om nødvendigt.

400 timers intervaller eller årligt

•

Udskift luftfilteret

• Udskift brændstoffilteret.

•

Servicér luftkølesystemet

•

Rengør finner på oliekøleren

Intervaller på 600 timer

• Udskift sikkerhedsfilteret, hvis monteret.

Rengør oftere under støvede forhold, eller når luftbåret snavs er til stede.

Ved hver 3. udskiftning af luftfilteret skal det indvendige sikkerhedsfilter udskiftes (hvis

monteret).

Elektronisk brændstofindsprøjtning (EFI)

EFI-systemet overvåger motortemperatur, motorhastighed og batterispænding under

start og opvarmning af motoren. Systemet skal ikke justeres. Hvis der opstår start- eller

betjeningsbesvær, skal du kontakte en autoriseret Briggs & Stratton-serviceforhandler.

BEMÆRKSørg for at følge nedenstående trin, ellers kan der opstå skader på EFI-

systemet.

• Start ALDRIG motoren, hvis batterikablerne er løse.

• Drej nøglen til FRA, før du frakobler, fjerner og/eller monterer batteriet.

• Start ALDRIG motoren ved hjælp af en batterioplader.

• Frakobl IKKE batterikablerne under motordrift.

• Når du tilslutter batterikablerne, skal du først tilslutte pluskablet (+) og derefter

minuskablet (-) til batteriet.

• Når batteriet oplades, skal du dreje tændingskontakten til stillingen FRAog

frakoble minuskablet (-) fra batteriet.

• Sprøjt IKKE vand direkte på det elektroniske styremodul.

Karburator og motorhastighed

Foretag ikke justeringer af karburatoren eller motorhastigheden. Karburatoren er

fabriksindstillet til at virke effektivt under de fleste omstændigheder. Undlad at ændre

ved regulatorfjederen, forbindelser eller andre dele, der er med til at øge motorens

hastighed. Hvis der er behov for justering, så kontakt en autoriseret serviceforhandler fra

Briggs & Stratton for service.

BEMÆRK

Denne udstyrsproducent specificerer maks. hastighed for motoren, som er installeret

på udstyret. Motoren må ikke køre med højere hastighed. Hvis du ikke er sikker på,

hvad maks. hastigheden er på udstyret, eller hvilken motorhastighed, der er indstillet

fra fabrikken af, så kontakt en autoriseret serviceforhandler fra Briggs & Stratton for

hjælp. For sikker og korrekt brug af udstyret skal motorhastigheden kun justeres af en

uddannet servicetekniker.

Eftersyn af tændrøret

Kontrollér afstanden for tændrøret (A, figur 8) med en afstandsmåler (B). Indstil om

nødvendigt tændrørsgabet. Monter og fastspænd tændrøret til det korrekte moment. Se

afsnittet Specifikationer for specifikationer mht. afstand og drejningsmoment.

BEMÆRK:I nogle lande kræves det af lokal lov, at du bruger et modstandstændrør

til at dæmpe tændingssignalet.Hvis der blev installeret et modstandstændrør af

udstyrsproducenten, skal du udskifte den med samme type.

Eftersyn af udstødningssystemet

ADVARSEL

Under drift bliver motoren og lyddæmperen varm. Hvis du rører ved en varm

motor, kan der opstå termiske forbrændinger.

Brændbart materiale, såsom blade, græs og krat, kan blive antændt.

• Før du berører motoren eller lyddæmperen, skal du stoppe motoren og vente to

(2) minutter. Sørg for, at motoren og lyddæmperen er sikre at røre ved.

• Fjern affald fra lyddæmperen og motoren.

Det er en overtrædelse af staten Californiens forskrifter om offentlige ressourcer, afsnit

4442, at bruge eller betjene motoren på ethvert skov-, krat- eller græsdækket område,

medmindre udstødningssystemet er forsynet med en korrekt vedligeholdt gnistfanger

som beskrevet i afsnit 4442. Andre stater eller statsretskredse har eventuelt lignende

love, se statsforskrift 36 CFR, afsnit 261.52. Kontakt en autoriseret fabrikant eller

serviceforhandler angående anskaffelse af en gnistfanger, der er konstrueret til det

udstødningssystem, der er monteret på den pågældende maskine.

Fjern affald fra området omkring lyddæmperen og cylinderen. Undersøg lyddæmperen

for revner, korrosion eller andre skader. Fjern udkastskærmen eller gnistfangeren, hvis

monteret, og undersøg for skader eller kulstofblokering. Hvis der er skade, skal der

monteres reservedele, før du betjener udstyret.

ADVARSEL

Reservedelene skal have samme udformning, og de skal placeres på præcist samme

måde som de originale dele. Andre dele kan medføre skade eller personskade.

Skift motorolie

ADVARSEL

Benzin og benzindampe er brændbare og eksplosive. Brand eller eksplosion kan

medføre forbrændinger eller dødsfald.

Under drift bliver motoren og lyddæmperen varm. Hvis du rører ved en varm

motor, kan der opstå termiske forbrændinger.

• Hvis du tømmer olien fra oliepåfyldningsrøret i toppen, skal brændstoftanken

være tom. Hvis den ikke er tom, kan der forekomme brændstoflækage og dette

kan forårsage brand eller eksplosion.

• Før du berører motoren eller lyddæmperen, skal du stoppe motoren og vente to

(2) minutter. Sørg for, at motoren og lyddæmperen er sikre at røre ved.

Brugt olie er et farligt affaldsprodukt og skal kasseres korrekt. Må ikke bortskaffes

sammen med husholdningsaffald. Kontakt de lokale myndigheder, dit servicecenter

eller din forhandler for oplysninger om sikker bortskaffelse eller korrekt aflevering til en

genbrugsstation.

Aftapning af olie

1. Med motoren STANDSET men stadig varm trækkes ledningen til tændrøret ud (D,

figur 9) og holdes væk fra tændrøret (E).

2. Fjern oliepinden (A, figur 10).

3. Afmonter olieaftapningsproppen (F, figur 11). Tap olien ud i en godkendt beholder.

4. Monter og spænd olieaftapningsproppen (F, figur 11).

Skift oliefilter, hvis monteret

1. Tap olien af motoren. Se afsnittet Aftapning af olie.

2. Fjern oliefilteret (H, figur 12), ogkassér det korrekt.

3. Inden du monterer det nye oliefilter, bør du smøre oliefilterets pakning let medren

olie.

4. Monter oliefilteret med hånden, indtil pakningenharkontaktmed oliefilterets

tilpasningsstykke, og fastgør derefter oliefilteret med 1/2 til 3/4 omgange.

5. Påfyld olie. Se afsnittet Påfyld olie.

6. Start, og brugmotoren. Når motoren er varm, skal der kontrolleresfor olielækage.

7. Stop motoren. Sørg for, at olieniveauet når op til toppen af fuld-mærket (B, figur 5)

på oliepinden.

Påfyld olie

• Kontrollér, at motoren står plant.

• Rengør oliepåfyldningsområdet for al snavs.

• Se afsnittetSpecifikationermht. oliekapacitet.

1. Fjern oliepinden (A, figur 10). Brug en ren klud til at fjerne olie fra oliepinden.

Not for

Reproduction

2. Hæld langsomt olie i motorpåfyldningen (C, figur 10). Undgå at overfylde. Vent i

et minut, og kontrollér oliestanden.

3. Sæt oliepinden i, og spænd den (A, figur 10).

4. Træk oliepinden op, og kontrollér oliestanden. Den korrekte olieniveau findes på

toppen af fuld-mærket (B, figur 10) på oliepinden.

5. Sæt oliepinden i, og spænd den (A, figur 10).

6. Tilslut tændrørsledningerne (D, figur 9) til tændrørene (E).

Eftersyn af luftfilteret

ADVARSEL

Benzindampe er brændbare og eksplosive. Brand eller eksplosion kan medføre

forbrændinger eller dødsfald.

• Startikke motoren, og lad den ikke køre uden luftfilterenheden (hvis monteret)

eller luftfilteret (hvis monteret).

BEMÆRK

Undlad at bruge komprimeret luft eller rengøringsmidler til rengøring af filteret.

Komprimeret luft kan beskadige filteret, og rengøringsmidler vil opløse filteret.

Se Vedligeholdelsesoversigten for servicekrav.

Forskellige modeller bruger et skum- eller papirfilter. Nogle modeller kan også have et

forfilter, der kan vaskes og genbruges. Sammenlign illustrationerne i denne manual med

den type, der er installeret på din motor, og servicér i overensstemmelse hermed.

Cyklonisk luftfilter

1. Åbn monteringsanordningerne (A, figur 13), og afmonter dækslet (B).

2. Fjern luftfilteret (C, figur 13).

3. For at løsne urenheder bankes luftfilteret forsigtigt mod en hård overflade. Hvis

luftfilteret er meget snavset, udskift det med et nyt filter.

4. Sikkerhedsfilteret (D, figur 13) kan, hvis monteret, fjernes ved at trække det

forsigtigt væk fra luftfilterenheden (E). Sørg for, at hverken snavs eller affald

trænger ind i motoren.

5. Monter det nye sikkerhedsfilter (D, figur 13) i luftfilterenheden (E).

6. Monter luftfilteret (C, figur 13) over sikkerhedsfilteret (D).

7. Monter dækslet (B, figur 13), og luk monteringsanordningerne (A).

Luftfilter, lav profil

1. Fjern monteringsanordningerne (A, figur 14).

2. Afmonter dækslet (B, figur 14).

3. Fjern monteringsanordningerne (C, figur 14), og holderen (D).

4. Fjern luftfilteret (E, figur 14).

5. Fjern forfilteret (F, figur 14), hvis monteret, fra luftfilteret (E).

6. For at løsne snavs bankes luftfilteret (E, figur 14) forsigtigt mod en hård overflade.

Hvis luftfilteret er meget snavset, udskift det med et nyt filter.

7. Rens forfilteret (F, figur 14), hvis monteret, med flydende rengøringsmiddel i vand.

Sørg for, at forfilteret er helt tørt. Smør ikke forfilteret.

8. Saml det tørre forfilter (F, figur 14), hvis monteret, på luftfilteret (E).

9. Monter luftfilteret (E, figur 14) med holderen (D) og fastgørelseselementerne (C).

10. Monter dækslet (B, figur 14) med fastgørelseselementerne (A). Sørg for, at

fastgørelseselementerne er strammet.

Vedligeholdelse af kølesystemet

ADVARSEL

Under drift bliver motoren og lyddæmperen varm. Hvis du rører ved en varm

motor, kan der opstå termiske forbrændinger.

Brændbart affald, såsom blade, græs og krat, kan blive antændt.

• Før du berører motoren eller lyddæmperen, skal du stoppe motoren og vente to

(2) minutter. Sørg for, at motoren og lyddæmperen er sikre at røre ved.

• Fjern affald fra lyddæmperen og motoren.

BEMÆRK

Brug ikke vand til at rengøre motoren. Vand kan forårsage forurening af

brændstofsystemet. Brug i stedet en børste eller en tør klud til at rengøre motoren.

Dette er en luftkølet motor. Snavs og rester kan stoppe luftstrømmen og medføre, at

motoren overophedes, så motorens ydelse svækkes, og dens levetid reduceres.

1. Anvend en børste eller en tør klud til at fjerne snavs fra luftindsugningsområdet (A,

figur15).

2. Sørg for, at forbindelseskabler, fjedre og betjeningsanordninger (B, figur15, 16) er

rene.

3. Hold området omkring og bag lyddæmperen (C, figur15, 16) fri for brændbart affald

for at undgå antænding af dette.

4. Sørg for, at oliekølerribberne (D, figur15) er fri for snavs og affald.

5. Løsn monteringsanordningerne (E, figur15, 16), og afmonter

affaldsadgangspanelerne (F). Fjern græs og snavs, der har ophobet sig på

cylinderne.

6. Installer affaldsadgangspanelerne (F, figur15, 16), og fastgør dem med

monteringsanordningerne(E).

Efter nogen tid kan der samle sig snavs i cylinderens køleribber, hvilket kan medføre,

at motoren overophedes. Dette snavs kan ikke fjernes uden delvist at skille motoren

ad. Få en autoriseret Briggs & Stratton-serviceforhandler til at inspicere og rengøre

luftkølesystemet som anbefalet i Vedligeholdelsesoversigten.

Vedligeholdelse af brændstofsystemet

ADVARSEL

Benzin og benzindampe er brændbare og eksplosive. Brand eller eksplosion kan

medføre forbrændinger eller dødsfald.

• Hold benzin væk fra gnister, åben ild, tændflammer, varme eller andre

antændelseskilder.

• Undersøg ofte brændstofledninger, brændstoftank, brændstofdæksel og

tilslutninger for revner eller lækager. Udskift beskadigede dele.

• Før rengøring eller udskiftning af brændstoffilteret skal brændstoftanken

tømmes, eller brændstofhanen lukkes.

• Hvis der spildes brændstof, skal du vente, indtil det tørrer, inden du starter

motoren.

• Reservedelene skal have samme udformning, og de skal placeres på præcist

samme måde som de originale dele. Andre dele kan medføre skade eller

personskade.

Brændstoffilter, hvis monteret

1. Før rengøring eller udskiftning af brændstoffilteret (A, figur 17) skal

brændstoftanken tømmes eller brændstofhanen lukkes. Hvis brændstoftanken ikke

tømmes, kan brændstof lække ud og forårsage brand eller eksplosion.

2. Brug en tang til at klemme tapperne (B, figur 17) på klemmerne (C) sammen, og flyt

derefter klemmerne væk fra brændstoffilteret (A). Drej og træk brændstofslangerne

(D) af brændstoffilteret.

3. Tjek brændstofslangerne (D, figur 17) for revner eller utætheder. Udskift efter

behov.

4. Udskift brændstoffilteret (A, figur 17) med et originalt udskiftningsfilter.

5. Fastgør brændstofslangerne (D, figur 17) med klemmer (C).

Opbevaring

Brændstofsystem

Se figur: 18.

Opbevar motoren på en plan overflade (almindelig driftsposition). Fyld brændstoftanken

(A, figur 18) med brændstof. Fyld ikke over brændstoftankens hals (B), da brændstoffet

kan ekspandere.

Brændstof kan blive forældet, når det opbevares i en opbevaringsbeholder i over 30

dage. Hver gang du fylder beholderen med brændstof, skal du tilføjetil brændstoffet

i overensstemmelse med producentens instruktioner. Det holder brændstoffet

frisk og formindsker antallet af brændstofrelaterede problemer eller forurening i

brændstofsystemet.

Det er ikke nødvendigt af tømme motoren for brændstof, nårtilføjes i henhold til

instruktionerne. TÆND motoren i to minutter før opbevaring for at føre brændstoffet og

stabilisatoren gennem brændstofsystemet.

Hvis benzinen i motoren ikke er blevet behandlet med en brændstofstabilisator,

skal den udtømmes i en godkendt beholder. Lad motoren køre, indtil den stopper

på grund af mangel på brændstof. Det anbefales at bruge en brændstofstabilisator i

opbevaringsbeholderen for at holde brændstoffet frisk.

Motorolie

Skift motorolien, mens motoren stadig er varm. Se afsnittet Udskift motorolien.

Fejlfinding

Hjælp

Hvis du har brug for hjælp, skal du kontakte din lokale forhandler eller gå til

vanguardpower.com eller ringe til 1-800-999-9333 (i USA).

18 vanguardpower.com

Not for

Reproduction

Specifikationer

Specifikationer og reservedele

Modeller: 540000 , 54E000

Forskydning 54.68 ci (896 cc)

Boring 3.366 tommer (85,5 mm)

Slaglængde 3.071 tommer (78,0 mm)

Oliekapacitet 78 - 80oz (2,3 - 2,4L)

Tændrørsgab .030 tommer (,76 mm)

Tilspændingsmoment for tændrør 180pund-tommer (20Nm)

Rotorelektrodeafstand .005 - .008 tommer (,13 - ,20 mm)

Ventilspillerum (indsugning) .004 - .006 tommer(,10 - ,15 mm)

Ventilspillerum (udstødning) .007 - .009 tommer (,18 - ,23 mm)

Modeller: 610000, 61E000, 61G200, 61G300

Forskydning 60.60 ci (993 cc)

Boring 3.366 tommer (85,5 mm)

Slaglængde 3.406 tommer (86,5 mm)

Oliekapacitet 78 - 80oz (2,3 - 2,4L)

Tændrørsgab .030 tommer (,76 mm)

Tilspændingsmoment for tændrør 180pund-tommer (20Nm)

Rotorelektrodeafstand .005 - .008 tommer (,13 - ,20 mm)

Ventilspillerum (indsugning) .004 - .006 tommer(,10 - ,15 mm)

Ventilspillerum (udstødning) .007 - .009 tommer (,18 - ,23 mm)

Reservedele - Modeller: 540000, 54E000,

610000, 61E000, 61G200, 61G300

Reservedel Delnummer

Cyklonisk luftfilter (figur 13) 841497

Cyklonisk sikkerhedsfilter (figur 13) 821136

Luftfilter, lavprofil (figur 14) 692519

Forfilter, lavprofil (figur 14) 692520

Olie ‒ SAE 30 100028

Oliefilter 842921

Brændstoffilter 691035

Tændrørsmodstand 491055

Platintændrør med ekstra lang levetid 5066

Tændrørsnøgle 19374

Gnisttester 19368

Motoreffekten falder med 3,5% for hver 1.000fod (300m) over havets overflade og

med 1% for hver 10°F (5,6°C) over 77°F (25°C). Motoren kan køre tilfredsstillende

ved en hældning på op til 15°. Yderligere oplysninger om sikre grænseværdier for drift

på hældninger findes i udstyrets betjeningsvejledning.

Nominel belastning

Nettobelastningen for separate benzinmotormodeller er mærket i henhold til SAE

(sammenslutningen af bilingeniører)-kode J1940, procedure til klassificering af lav

motorkraft og drejningsmoment, og den er klassificeret i henhold til SAE J1995.

Drejningsmomentværdier er målt ved 2.600 o/min. for motorer med “rpm” angivet

på mærkaten og 3.060 o/min. for alle andre; hestekræftværdier er angivet ved

3.600 o/min. Bruttoeffektkurverne kan ses på www.BRIGGSandSTRATTON.COM.

Nettokraftværdier bliver målt med udstødnings- og luftfilter monteret, hvorimod

bruttokraftværdier bliver målt uden disse anordninger. Faktisk bruttomotoreffekt vil være

højere end nettomotoreffekt og er bl.a. påvirket af lokale driftsforhold og variationer

fra motor til motor. På grund af det store udvalg af ekstraudstyr, der kan benyttes

sammen med motorer, yder benzinmotoren måske ikke den forventede bruttoeffekt,

når den anvendes med et bestemt stykke ekstraudstyr. Forskellen skyldes mange

forskellige faktorer, herunder eksempelvis de forskellige motordele (luftfilter, udstødning,

opladning, kølesystem, karburator, brændstofpumpe osv.), anvendelsesbegrænsninger,

omgivelsernes driftsforhold (temperatur, fugtighed, højde) samt motor-til-motor-variation.

På grund af fabrikations- og kapacitetsbegrænsninger kan Briggs & Stratton erstatte en

motor med højere effekt for denne motor.

Garanti

Briggs & Stratton – Motorgaranti

Gældende fra januar 2019

Begrænset garanti

Briggs & Stratton garanterer, at i løbet af garantiperioden, der er angivet nedenfor,

vil vi reparere eller udskifte enhver del, der er defekt i materiale eller håndværk eller

begge dele, uden beregning. Transportomkostninger i forbindelse med et produkt, som

indleveres til reparation eller udskiftning under denne garanti, afholdes af køberen.

Denne garanti er gyldig inden for tidsperioderne og underlagt nedenstående betingelser.

Find den nærmeste autoriserede serviceforhandler på kortet over forhandlere på

BRIGGSandSTRATTON.COM i forbindelse med service under garantien. Køberen skal

kontakte den autoriserede serviceforhandler og derefter stille produktet til rådighed for

den autoriserede serviceforhandler med henblik på inspektion og afprøvning.

Der ydes ikke nogen anden udtrykkelig garanti. Underforståede garantier,

inklusive garantier for salgbarhed og egnethed til et bestemt formål, er begrænset

til garantiperioden, der er angivet nedenfor, eller i den udstrækning loven tillader.

Ansvar for hændelige skader eller følgeskader er udelukket, i det omfang lovgivningen

tillader udelukkelse. Visse stater eller lande tillader ikke begrænsninger på, hvor lang

tid en underforstået garanti varer, og visse stater eller lande tillader ikke udelukkelse

eller begrænsning af tilfældig skade eller følgeskade, så ovenstående begrænsning

og udelukkelse er måske ikke gældende for dig. Denne garanti giver dig specifikke,

juridiske rettigheder, og du kan endvidere have andre rettigheder, som kan variere fra

land til land

Vilkår for standardgaranti

1, 2, 3

Vanguard®; Commercial Series

Forbrugeranvendelse - 36 måneder

Erhvervsmæssig anvendelse - 36 måneder

XR-serien

Forbrugeranvendelse - 24 måneder

Erhvervsmæssig anvendelse - 24 måneder

Alle andre motorer med Dura-Bore™ støbejernsboring

Forbrugeranvendelse - 24 måneder

Erhvervsmæssig anvendelse - 12 måneder

Alle andre motorer

Forbrugeranvendelse - 24 måneder

Erhvervsmæssig anvendelse - 3 måneder

1

Dette er vores vilkår for standardgaranti, men der kan lejlighedsvist være

ekstra garantidækning, der ikke var fastslået på tidspunktet for offentliggørelsen.

Hvis du ønsker en liste over gældende garantivilkår for din motor, så gå til

BRIGGSandSTRATTON.com, eller kontakt din autoriserede Briggs & Stratton-

serviceforhandler.

2

Der er ikke garanti på motorer på udstyr, der bruges til primæreffekt i stedet

for et hjælperedskab; standbygeneratorer, der anvendes til kommercielle

formål, hjælpekøretøjer, der overstiger 25mph, eller motorer, der bruges til

konkurrencemæssige motorløb eller på kommercielle eller lejebaserede baner.

3

Vanguard installeret på standbygeneratorer: 24 måneders forbrugeranvendelse,

ingen garanti for erhvervsmæssig anvendelse. Kommerciel serie med

fremstillingsdato før juli 2017: 24 måneder ved privat anvendelse, 24 måneder ved

erhvervsmæssig anvendelse.

4

I Australien - Vores produkter sælges med en garanti, der ikke kan bortfalde

i henhold til den australske forbrugerlovgivning. Du er berettiget til en erstatning

eller refusion i tilfælde af en væsentlig defekt eller til kompensation for ethvert

forudseeligt tab eller skade. Du er derudover berettiget til at få dine varer repareret

eller erstattet, hvis varerne ikke lever op til kvaliteten, og manglen ikke er i

forbindelse med en væsentlig defekt. I forbindelse med service under garantien

findes den nærmeste autoriserede serviceforhandler på kortet over forhandlere på

BRIGGSandSTRATTON.COM, ved at ringe til 1300 274 447 eller ved at sende en

e-mail eller skrive til [email protected], Briggs & Stratton

Australia Pty Ltd, 1 Moorebank Avenue, Moorebank, NSW, Australia, 2170.

Garantiperioden starter på købsdatoen for den første almindelige eller erhvervsmæssige

bruger. “Privat brug” betyder brug i personlig beboelseshusholdning af en detailkunde.

“Erhvervsmæssig brug” betyder al anden form for brug, inklusive erhvervsmæssigt,

indkomstdannende eller lejebaseret formål. Når en motor har været anvendt

erhvervsmæssigt, skal den herefter anses for at være en motor til erhvervsbrug i

henhold til denne garanti.

Gem dit købsbevis. Hvis du ikke kan fremvise bevis for den oprindelige

købsdato på det tidspunkt, hvor du anmoder om garantiservice, vil produktets

produktionsdato blive brugt som grundlag for garantien. Det er ikke nødvendigt at

registrere dit produkt for at opnå garanti på Briggs & Stratton-produkter.

Om garantien

Denne garanti dækker alene motor-relaterede materiale- og/eller fremstillingsfejl og ikke

udskiftning eller tilbagebetaling for det redskab, hvorpå motoren måtte være monteret.

Not for

Reproduction

Rutinemæssig vedligeholdelse, optuninger, justeringer eller normal slitage dækkes ikke

under denne garanti. På samme måde gælder denne garanti heller ikke, hvis motoren er

ændret eller modificeret, eller hvis motorens serienummer er ødelagt eller fjernet. Denne

garanti dækker ikke motorskade eller driftsproblemer som følge af:

1. Brug af dele, der ikke er originale dele fra Briggs & Stratton

2. Betjening af motoren med utilstrækkelig, forurenet eller forkert type olie

3. Brug af forurenet eller gammel olie, benzin med mere end 10% etanol eller brug

af alternative brændstoffer som petroleumsvæske eller naturgas på motorer, der

ikke oprindeligt er udviklet/fremstillet af Briggs & Stratton til at fungere med sådanne

brændstoffer

4. Snavs, der er trængt ind i motoren på grund af utilstrækkelig vedligeholdelse af

luftrensesystemet eller genmontering

5. Stød mod et objekt med skærebladet i en roterende plæneklipper, løse eller forkert

installerede bladadaptere, rotorer eller andet udstyr koblet på krumtapakslen eller

for høj V-remspænding

6. Tilhørende dele eller tilbehør som koblinger, transmissioner, udstyrskontroller osv.,

som ikke leveres af Briggs & Stratton

7. Overophedning på grund af græsslåning, snavs og affald eller gnaverreder,

der tilstopper kølefinnerne eller svinghjulsområdet eller drift af motoren uden

tilstrækkelig ventilation

8. Overdreven vibration på grund af for høj hastighed, løs motormontering, løse eller

ubalancerede skæreblade eller rotorer eller forkert kobling af udstyrskomponenter

på krumtapakslen

9. Misbrug, mangel på rutinevedligeholdelse, forsendelse, håndtering eller udstyrets

opbevaring på lager eller forkert motorinstallation.

Servicegarantien er kun tilgængelig via autoriserede Briggs & Stratton-

serviceforhandlere. Find din nærmeste serviceforhandler på vores forhandlerkort

på BRIGGSandSTRATTON.COM, eller ved at ringe til 1-800-233-3723 (i USA).

80004537 (Rev. F)

20 vanguardpower.com

Not for

Reproduction

La page charge ...

Simplicity ENG, MDL 610000 Manuel utilisateur

Marque: Simplicity

Modèle: ENG, MDL 610000

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

italiano: Simplicity ENG, MDL 610000 Manuale utente
English: Simplicity ENG, MDL 610000 User manual
español: Simplicity ENG, MDL 610000 Manual de usuario
Deutsch: Simplicity ENG, MDL 610000 Benutzerhandbuch
Nederlands: Simplicity ENG, MDL 610000 Handleiding
português: Simplicity ENG, MDL 610000 Manual do usuário
dansk: Simplicity ENG, MDL 610000 Brugermanual
svenska: Simplicity ENG, MDL 610000 Användarmanual
suomi: Simplicity ENG, MDL 610000 Ohjekirja

Simplicity ENG, MDL 610000 Manuel utilisateur

Simplicity ENG, MDL 610000 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents