IKEA LAGAN Manuel utilisateur

LAGAN

GB

DE

FR

IT

ENGLISH 4

DEUTSCH 19

FRANÇAIS 35

ITALIANO 57

Contents

Safety instructions 4

Product description 6

Control panel 6

Programmes 6

Options 7

Before first use 8

Daily use 9

Hints and tips 11

Care and cleaning 12

Troubleshooting 13

Technical information 15

Environment concerns 16

IKEA GUARANTEE 16

Subject to change without notice.

Safety instructions

Before the installation and use of the appli-

ance, carefully read the supplied instruc-

tions. The manufacturer is not responsible if

an incorrect installation and use causes inju-

ries and damages. Always keep the instruc-

tions with the appliance for future reference.

Only a qualified service engineer can repair

this appliance. Use only original spare

parts.

To prevent injury and damage to the appli-

ance, do not try to repair the appliance. Al-

ways contact the After Sales Service.

Children and vulnerable people safety

Warning! Risk of suffocation, injury or

permanent disability.

• Do not let persons, children included, with

reduced physical sensory, reduced men-

tal functions or lack of experience and

knowledge use the appliance. They must

have supervision or instruction for the op-

eration of the appliance by a person who

is responsible for their safety. Do not let

children play with the appliance.

• Keep all packaging away from children.

• Keep all detergents away from children.

• Keep children and pets away from the

appliance door when it is open.

Installation

• Remove all the packaging.

• Do not install or use a damaged appli-

ance.

• Do not install or use the appliance where

the temperature is less than 0 °C.

• Obey the installation instruction supplied

with the appliance.

• Make sure that the appliance is installed

below and adjacent to safe structures.

Water connection

• Make sure not to cause damage to the

water hoses.

• Before you connect the appliance to new

pipes or pipes not used for a long time,

let the water flow until it is clean.

• The first time you use the appliance,

make sure that there is no leakage.

• The water inlet hose has a safety valve

that prevents the hose to loosen. To dis-

connect the hose, press the lever (B) and

turn the fastener (A) clockwise.

A

B

• The water inlet hose has an external

transparent sheath. If the hose is dam-

aged, the water in the hose becomes

dark.

• If the water inlet hose is damaged, imme-

diately disconnect the mains plug from

the mains socket. Contact the service to

replace the water inlet hose.

ENGLISH 4

Electrical connection

Warning! Risk of fire and electrical

shock.

• The appliance must be earthed.

• Make sure that the electrical information

on the rating plate agrees with the power

supply. If not, contact an electrician.

• Always use a correctly installed shock-

proof socket.

• Do not use multi-plug adapters and ex-

tension cables.

• Make sure not to cause damage to the

mains plug and to the mains cable. Con-

tact the service or an electrician to

change a damaged mains cable.

• Connect the mains plug to the mains

socket only at the end of the installation.

Make sure that there is access to the

mains plug after the installation.

• Do not pull the mains cable to disconnect

the appliance. Always pull the mains

plug.

•

This appliance complies with the E.E.C.

Directives.

Use

• This appliance is intended to be used in

household and similar applications such

as:

– Staff kitchen areas in shops, offices and

other working environments

–Farm houses

– By clients in hotels, motels and other

residential type environments

– Bed and breakfast type environments.

Warning! Risk of injury.

• Do not change the specification of this

appliance.

• Put knives and cutlery with sharp points in

the cutlery basket with the points down or

in a horizontal position.

• Do not keep the appliance door open

without supervision to prevent to fall on it.

• Do not sit or stand on the open door.

• Dishwasher detergents are dangerous.

Obey the safety instructions on the deter-

gent packaging.

• Do not drink and play with the water in

the appliance.

• Do not remove the dishes from the appli-

ance until the programme is completed.

There can be detergent on the dishes.

Warning! Risk of electrical shock, fire

or burns.

• Do not put flammable products or items

that are wet with flammable products in,

near or on the appliance.

• Do not use water spray and steam to

clean the appliance.

• The appliance can release hot steam if

you open the door while a programme

operates.

Disposal

Warning! Risk of injury or suffocation.

• Disconnect the appliance from the mains

supply.

• Cut off the mains cable and dispose of it.

• Remove the door catch to prevent chil-

dren and pets to get closed in the appli-

ance.

ENGLISH 5

Product description

8

7

6

5

4

1

3

2

1

Lower spray arm

2

Filters

3

Rating plate

4

Rinse aid dispenser

5

Detergent dispenser

6

Salt container

7

Upper spray arm

8

Upper basket

Control panel

4

2

3

1

On/off button

2

Programme indicators

3

Indicators

4

Program button

Indicators Description

Salt indicator. It is always off while the programme operates.

End indicator.

Programmes

Programme

1)

Degree of soil

Type of load

Programme

phases

Duration

(min)

Energy

(kWh)

Water

(l)

2)

Heavy soil

Crockery, cut-

lery, pots and

pans

Prewash

Wash 70 °C

Rinses

Dry

130 - 150 1.3 - 1.4 13 - 15

ENGLISH 6

Programme

1)

Degree of soil

Type of load

Programme

phases

Duration

(min)

Energy

(kWh)

Water

(l)

Normal soil

Crockery and

cutlery

Prewash

Wash 65 °C

Rinses

Dry

100 - 110 1.2 - 1.6 15 - 16

3)

Normal soil

Crockery and

cutlery

Prewash

Wash 50 °C

Rinses

Dry

195 1.02 15

1) The pressure and the temperature of the water , the variations of the mains supply, the options and the quantity of

dishes can change the values.

2) This program is indicated for heavy soil loading to get the sufficient cleaning results on the pots and pans.

3) With this programme you have the most efficient use of water and energy consumption for crockery and cutlery with

normal soil. (This is the standard programme for test institutes).

Information for test institutes

For all the necessary information for test performance. send an email to:

info.test@dishwasher-production.com

Write down the product number (PNC) that is on the rating plate.

Options

Acoustic signals

The acoustic signals operate when the ap-

pliance has a malfunction and it is not pos-

sible to deactivate them.

There is also an acoustic signal that oper-

ates when the programme is completed. By

default, this acoustic signal is on, but it is

possible to deactivate it.

How to deactivate the acoustic signal for

the end of programme

1. Press the on/off button to activate the

appliance. Make sure that the appli-

ance is in setting mode, refer to “Setting

and starting a programme”.

2. Press and hold Program until the pro-

gramme indicator

starts to flash and

the programme indicator

comes on

with fixed light.

3. Press immediately Program.

•

The programme indicator

comes

on with fixed light.

•

The programme indicator

starts

to flash.

4.

Wait until the programme indicator

goes off. The programme indicator

continues to flash. The end indicator is

on.

5. Press Program. The end indicator goes

off. The acoustic signal for the end of

programme is deactivated.

6. Press the on/off button to deactivate the

appliance and to confirm the setting.

How to activate acoustic signal for the

end of programme

1. Refer to “How to activate the acoustic

signal for the end of programme” and

follow the procedure from step (1) to

step (4). The end indicator is off.

ENGLISH 7

2. Press Program. The end indicator comes

on. The acoustic signal for the end of

programme is activated.

3. Press the on/off button to deactivate the

appliance and to confirm the setting.

Before first use

1. Make sure that the set level of the water

softener agrees with the water hardness

in your area. If not, adjust the water

softener. Contact your local water au-

thority to know the water hardness in

your area.

2. Fill the salt container.

3. Fill the rinse aid dispenser.

4. Open the water tap.

5. Processing residues can stay in the ap-

pliance. Start a programme to remove

them. Do not use detergent and do not

load the baskets.

Adjusting the water softener

Water hardness

Water softener

adjustment

German

degrees

(°dH)

French

degrees

(°fH)

mmol/l Clarke

degrees

Level

47 - 50 84 - 90 8.4. - 9.0 58 - 63 10

43 - 46 76 - 83 7.6 - 8.3 53 - 57 9

37 - 42 65 - 75 6.5 - 7.5 46 - 52 8

29 - 36 51 - 64 5.1 - 6.4 36 - 45 7

23 - 28 40 - 50 4.0 - 5.0 28 - 35 6

19 - 22 33 - 39 3.3 - 3.9 23 - 27

5

1)

15 - 18 26 - 32 2.6 - 3.2 18 - 22 4

11 - 14 19 - 25 1.9 - 2.5 13 - 17 3

4 - 10 7 - 18 0.7 - 1.8 5 - 12 2

< 4 < 7 < 0.7 < 5

1

2)

1) Default setting.

2) Do not use salt at this level.

How to adjust the level of the water

softener

1. Press the on/off button to activate the

appliance. Make sure that the appli-

ance is in setting mode, refer to “Setting

and starting a programme”.

2. Press and hold Program until the pro-

gramme indicator

starts to flash and

the programme indicator

comes on

with fixed light.

3.

Wait until the programme indicator

goes off. The programme indicator

continues to flash. The end indicator

starts to flash. The intermittent flashing

of the end indicator refers to the current

set level.

• E.g. 5 flashes + pause + 5 flashes =

level 5.

4. Press Program again and again to

change the setting. Each time you press

Program the level number increases.

ENGLISH 8

5. Press the on/off button to deactivate the

appliance and to confirm the setting.

Filling the salt container

Caution! Water and salt can come out

from the salt container when you fill it.

Risk of corrosion. To prevent this, after the

replenishment, start a programme.

1

2

3

Put 1 litre of water

in the salt container

(only for the first

time).

4

Put 1 kg of salt in

the salt container.

5

6

Filling the rinse aid dispenser

1

2

3

+

-

M

A

X

4

5

+

-

M

A

X

A

Fill the rinse aid dis-

penser when the

lens (A) is clear.

6

To adjust the re-

leased quantity of

rinse aid, turn the

selector between

position 1 (lowest

quantity) and posi-

tion 4 (highest

quantity). Refer to

‘TROUBLESHOOT-

ING’.

Daily use

1. Open the water tap. 2. Press the on/off button to activate the

appliance. Make sure that the appli-

ENGLISH 9

ance is in setting mode. Refer to ’SET-

TING AND STARTING A PROGRAMME’.

• If the salt indicator is on, fill the salt

container.

3. Make sure that there is rinse aid in the

rinse aid dispenser.

4. Load the baskets.

5. Add the detergent.

6. Set and start the correct programme for

the type of load and the degree of soil.

Using the detergent

1

2

3

A A

Put the detergent or the tablet in the com-

partment (A).

4

B

If the programme

has a prewash

phase, put a small

quantity of deter-

gent in compart-

ment (B).

5

Using the combi detergent tablets

When you use tablets, that contain salt and

rinse aid, do not fill the salt container and

the rinse aid dispenser. The rinse aid indi-

cator always comes on if the rinse aid dis-

penser is empty.

1. Adjust the water softener to the lowest

level.

2. Set the rinse aid dispenser to the lowest

position.

If you stop to use the combi detergent

tablets, before you start to use separately

detergent, rinse aid and dishwasher salt,

do these steps:

1. Press the on/off button to activate the

appliance.

2. Set the water softener to the highest lev-

el.

3. Make sure that the salt container and

the rinse aid dispenser are full.

4. Start the shortest programme with a

rinsing phase, without detergent and

without dishes.

5. Adjust the water softener to the water

hardness in your area.

6. Adjust the released quantity of rinse aid.

Setting and starting a programme

Setting mode

For some settings it is necessary that the

appliance is in setting mode.

The appliance is in setting mode when, af-

ter the activation, all the programme indi-

cators are on.

If the control panel does not show this con-

dition press and hold the programme but-

ton until all the programme indicators come

on

Starting a programme

1. Open the water tap.

2. Press the on/off button to activate the

appliance. Make sure that the appli-

ance is in setting mode.

3. Press Program again and again until

only the indicator of the programme you

want to set is on.

4. Close the appliance door. The pro-

gramme starts.

ENGLISH 10

Opening the door while the appliance

operates

If you open the door, the appliance stops.

When you close the door, the appliance

continues from the point of interruption.

Cancelling the programme

1. Open the appliance door.

2. Press and hold the programme button

until all the programme indicators come

on.

Make sure that there is detergent in

the detergent dispenser before you

start a new programme.

At the end of the programme

The end indicator comes on.

1. Press the on/off button to deactivate the

appliance.

2. Close the water tap.

If you do not press the on/off button,

after few minutes from the end of the

programme all the indicators go off.

This helps to decrease the energy consump-

tion,

• Let the dishes become cold before

you remove them from the appli-

ance. Hot dishes can be easily dam-

aged.

• First remove the items from the lower

basket, then from the upper basket.

• There can be water on the sides and

on the door of the appliance. Stain-

less steel becomes cool more quickly

than the dishes.

Hints and tips

The water softener

Hard water contains a high quantity of min-

erals that can cause damage to the appli-

ance and bad washing results. The water

softener neutralises these minerals.

The dishwasher salt keeps the water soften-

er clean and in good conditions. It is impor-

tant to set the right level of the water soft-

ener. This makes sure that the water soften-

er uses the correct quantity of dishwasher

salt and water.

Loading the baskets

Refer to the supplied leaflet with ex-

amples of the load of the baskets.

• Only use the appliance to wash items

that are dishwasher-safe.

• Do not put in the appliance items made

of wood, horn, aluminium, pewter and

copper.

• Do not put in the appliance items that

can absorb water (sponges, household

cloths).

• Remove remaining food from the items.

• To remove easily remaining burned food,

soak pots and pans in water before you

put them in the appliance.

• Put hollow items (cups, glasses and pans)

with the opening down.

• Make sure that cutlery and dishes do not

bond together. Mix spoons with other

cutlery.

• Make sure that glasses do not touch oth-

er glasses.

• Put the small items in the cutlery basket.

• Put the light items in the upper basket.

Make sure that they do not move.

• Make sure that the spray arms can move

freely before you start a programme.

Using salt, rinse aid and detergent

• Only use salt, rinse aid and detergent for

dishwasher. Other products can cause

damage to the appliance.

• The rinse aid helps, during the last rinsing

phase, to dry the dishes without streaks

and stains.

ENGLISH 11

• Combi detergent tablets contain deter-

gent, rinse aid and other added agents.

Be sure that these tablets are applicable

to the water hardness in your area. Refer

to the instructions on the packaging of the

products.

• Detergent tablets do not fully dissolve

with short programmes. To prevent deter-

gent residues on the tableware, we rec-

ommend that you use the tablets with

long programmes.

• Do not use more than the correct quantity

of detergent. Refer to the instructions on

the detergent packaging.

Before starting a programme

Make sure that:

• The filters are clean and correctly instal-

led.

• The spray arms are not clogged.

• The position of the items in the baskets is

correct.

• The programme is applicable for the type

of load and for the degree of soil.

• The correct quantity of detergent is used.

• There is dishwasher salt and rinse aid

(unless you use combi detergent tablets).

• The cap of the salt container is tight.

Care and cleaning

Warning! Before maintenance,

deactivate the appliance and

disconnect the mains plug from the mains

socket.

Dirty filters and clogged spray arms

decrease the washing results.

Make a check regularly and, if necessary,

clean them.

Cleaning the filters

1

2

C

B

A

3 4

To remove filters (B)

and (C), turn the

handle counter-

clockwise and re-

move. Pull apart fil-

ter (B) and (C).

Wash the filters with

water.

ENGLISH 12

5

Remove filter (A).

Wash the filter with

water.

6

D

Put filter (A) to its

initial position.

Make sure that it

assembles correctly

under the two

guides (D).

7

8

Assemble filters (B)

and (C). Put them

into position in filter

(A). Turn the handle

clockwise until it

locks.

An incorrect position of the filters can

cause bad washing results and dam-

age to the appliance.

Cleaning the filter of inlet hose

1

Close the water tap.

2

A

B

Disconnect the

hose. Press the lever

B and turn the fas-

tener A clockwise.

3

Clean the filter of

inlet hose.

4

Cleaning the spray arms

Do not remove the spray arms.

If the holes in the spray arms are clogged,

remove remaining parts of soil with a thin

pointed object.

External cleaning

Clean the appliance with a moist soft cloth.

Only use neutral detergents. Do not use

abrasive products, abrasive cleaning pads

or solvents.

Troubleshooting

The appliance does not start or it stops dur-

ing operation.

Before you contact the Service, refer to the

information that follows for a solution to the

problem.

With some problems, different indicators

flash continuously or intermittently at the

same time to show an alarm code.

ENGLISH 13

Alarm code Problem

• The indicator of the set programme flash-

es continuously.

• The end indicator flashes 1 time intermit-

tently.

The appliance does not fill with water.

• The indicator of the set programme flash-

es continuously.

• The end indicator flashes 2 times intermit-

tently.

The appliance does not drain the water.

• The indicator of the set programme flash-

es continuously.

• The end indicator flashes 3 times intermit-

tently.

The anti-flood device is on.

Warning! Deactivate the appliance

before you do the checks.

Problem Possible cause Possible solution

The programme does

not start.

The mains plug is not connec-

ted in the mains socket.

Connect the mains plug.

The appliance door is open. Close the appliance door.

The fuse in the fuse box is

damaged.

Replace the fuse.

The appliance does

not fill with water.

The water tap is closed. Open the water tap.

The water pressure is too low. Contact your local water au-

thority.

The water tap is clogged or

there is limescale on it.

Clean the water tap.

The filter in the water inlet hose

is clogged.

Clean the filter.

The water inlet hose has a kink

or a bend.

Make sure that the position of

the hose is correct.

The anti-flood device is on.

There are water leakages in

the appliance.

Close the water tap and con-

tact the service.

The appliance does

not drain the water.

The sink spigot is clogged. Clean the sink spigot.

The water drain hose has a

kink or a bend.

Make sure that the position of

the hose is correct.

ENGLISH 14

Problem Possible cause Possible solution

The salt indicator con-

tinues to stay on after

the replenishment of

the salt container.

This can occur when you are

using salt that needs more time

to dissolve.

There is no unwanted effect on

the performance of the appli-

ance.

If after 3 or 4 programmes, the

salt indicator continues to stay

on, contact the service.

After the checks are completed, activate the

appliance. The programme continues from

the point of interruption.

If the problem occurs again, contact the

service.

If other alarm codes show, contact the serv-

ice.

If the washing and drying results are not

satisfactory

Whitish streaks or bluish layers on glasses

and dishes

• The released quantity of rinse aid is too

much. Adjust the rinse aid selector to a

lower position.

• The quantity of detergent is too much.

Stains and dry water drops on glasses

and dishes

• The released quantity of rinse aid is not

sufficient. Adjust the rinse aid selector to

a higher position.

• The quality of the detergent can be the

cause.

Dishes are wet

• The programme is without a drying

phase or with a low temperature drying

phase.

• The rinse aid dispenser is empty.

• The quality of the rinse aid can be the

cause.

Refer to ‘HINTS AND TIPS’ for other

possible causes.

Technical information

Dimensions Width / Height / Depth (mm) 596 / 818 - 898 / 555

Electrical connection Refer to the rating plate.

Voltage 220-240 V

Frequency 50 Hz

Water supply pressure Min. / max. (bar / MPa) (0.5 / 0.05 ) / (8 / 0.8 )

Water supply

1)

Cold water or hot water

2)

max. 60 °C

Capacity Place settings 12

Power consumption Left-on mode 0.50 W

Off-mode 0.50 W

1) Connect the water inlet hose to a water tap with a 3/4'' thread.

2) If the hot water comes from alternative sources of energy, (e.g. solar panels, aeolian energy), use the hot water

supply to decrease energy consumption.

ENGLISH 15

Environment concerns

Recycle the materials with the symbol .

Put the packaging in applicable containers

to recycle it.

Help protect the environment and human

health and to recycle waste of electrical

and electronic appliances. Do not dispose

appliances marked with the symbol

with

the household waste. Return the product to

your local recycling facility or contact your

municipal office.

• Discard correctly the packaging material.

Recycle the materials with the symbol

.

IKEA GUARANTEE

How long is the IKEA guarantee valid?

This guarantee is valid for five (5) years

from the original date of purchase of Your

appliance at IKEA, unless the appliance is

named LAGAN in which case two (2) years

of guarantee apply. The original sales re-

ceipt is required as proof of purchase. If

service work is carried out under guarantee,

this will not extend the guarantee period for

the appliance,

Which appliances are not covered by the

IKEA five (5) years guarantee?

The range of appliances named LAGAN

and all appliances purchased in IKEA be-

fore 1st of August 2007

Who will execute the service?

IKEA service provider will provide the serv-

ice through its own service operations or

authorized service partner network.

What does this guarantee cover?

The guarantee covers faults of the appli-

ance, which have been caused by faulty

construction or material faults from the date

of purchase from IKEA. This guarantee ap-

plies to domestic use only. The exceptions

are specified under the headline “What is

not covered under this guarantee?” Within

the guarantee period, the costs to remedy

the fault e.g. repairs, parts, labour and trav-

el will be covered, provided that the appli-

ance is accessible for repair without special

expenditure. On these conditions the EU

guidelines (Nr. 99/44/EG) and the respec-

tive local regulations are applicable. Re-

placed parts become the property of IKEA.

What will IKEA do to correct the problem?

IKEA appointed service provider will exam-

ine the product and decide, at its sole dis-

cretion, if it is covered under this guarantee.

If considered covered, IKEA service provider

or its authorized service partner through its

own service operations, will then, at its sole

discretion, either repair the defective prod-

uct or replace it with the same or a compa-

rable product.

What is not covered under this

guarantee?

• Normal wear and tear.

• Deliberate or negligent damage, dam-

age caused by failure to observe operat-

ing instructions, incorrect installation or by

connection to the wrong voltage, dam-

age caused by chemical or electro-chem-

ical reaction, rust, corrosion or water

damage including but not limited to dam-

age caused by excessive lime in the wa-

ter supply, damage caused by abnormal

environmental conditions.

• Consumable parts including batteries

and lamps.

• Non-functional and decorative parts

which do not affect normal use of the ap-

pliance, including any scratches and pos-

sible color differences.

• Accidental damage caused by foreign

objects or substances and cleaning or un-

blocking of filters, drainage systems or

soap drawers.

ENGLISH 16

• Damage to the following parts: ceramic

glass, accessories, crockery and cutlery

baskets, feed and drainage pipes, seals,

lamps and lamp covers, screens, knobs,

casings and parts of casings. Unless such

damages can be proved to have been

caused by production faults.

• Cases where no fault could be found dur-

ing a technician’s visit.

• Repairs not carried out by our appointed

service providers and/or an authorized

service contractual partner or where non-

original parts have been used.

• Repairs caused by installation which is

faulty or not according to specification.

• The use of the appliance in a non-domes-

tic environment i.e. professional use.

• Transportation damages. If a customer

transports the product to their home or

other address, IKEA is not liable for any

damage that may occur during transport.

However, if IKEA delivers the product to

the customer's delivery address, then

damage to the product that occurs during

this delivery will be covered by this guar-

antee.

• Cost for carrying out the initial installation

of the IKEA appliance. However, if an

IKEA service provider or its authorized

service partner repairs or replaces the

appliance under the terms of this guaran-

tee, the service provider or its authorized

service partner will re-install the repaired

appliance or install the replacement, if

necessary.

This restriction do not apply to fault-free

work carried out by a qualified specialist

using our original parts in order to adapt

the appliance to the technical safety specifi-

cations of another EU country.

How country law applies

The IKEA guarantee gives You specific legal

rights, which covers or exceed local de-

mands. However these conditions do not

limit in any way consumer rights described

in the local legislation

Area of validity

For appliances which are purchased in one

EU country and taken to another EU coun-

try, the services will be provided in the

framework of the guarantee conditions nor-

mal in the new country. An obligation to

carry out services in the framework of the

guarantee exists only if the appliance com-

plies and is installed in accordance with:

• the technical specifications of the country

in which the guarantee claim is made;

• the Assembly Instructions and User Man-

ual Safety Information;

The dedicated After Sales Service for

IKEA appliances:

Please do not hesitate to contact IKEA After

Sales Service to:

1. make a service request under this guar-

antee;

2. ask for clarification on installation of the

IKEA appliance in the dedicated IKEA

kitchen furniture. The service won’t pro-

vide clarifications related to:

– the overall IKEA kitchen installation;

– connections to electricity (if machine

comes without plug and cable), to

water and to gas since they have to

be executed by an authorized serv-

ice engineer.

3. ask for clarification on user manual con-

tents and specifications of the IKEA ap-

pliance.

To ensure that we provide you with the best

assistance, please read carefully the As-

sembly Instructions and/or the User Manual

section of this booklet before contacting us.

How to reach us if You need our service

Please refer to the last page of this manual

for the full list of IKEA appointed contacts

and relative national phone numbers.

ENGLISH 17

Important! In order to provide You with a

quicker service, we recommend that You

use the specific phone numbers listed at the

end of this manual. Always refer to the

numbers listed in the booklet of the specific

appliance You need an assistance for.

Before calling us, assure that You have to

hand the IKEA article number (8 digit code)

for the appliance of which you need our

assistance.

Important! SAVE THE SALES RECEIPT! It is

Your proof of purchase and required for the

guarantee to apply. Note that the receipt

reports also the IKEA article name and

number (8 digit code) for each of the

appliances you have purchased.

Do You need extra help?

For any additional questions not related to

After Sales of your appliances, please con-

tact our nearest IKEA store call centre. We

recommend you read the appliance docu-

mentation carefully before contacting us.

ENGLISH 18

Inhalt

Sicherheitshinweise 19

Gerätebeschreibung 21

Bedienfeld 21

Programme 22

Optionen 22

Vor der ersten Inbetriebnahme 23

Täglicher Gebrauch 25

Tipps und Hinweise 27

Reinigung und Pflege 28

Fehlersuche 30

Technische Daten 31

Umwelttipps 32

IKEA Garantie 32

Änderungen vorbehalten.

Sicherheitshinweise

Lesen Sie die mitgelieferte Anleitung sorg-

fältig vor der Montage und dem ersten Ge-

brauch des Geräts durch. Der Hersteller ist

nicht dafür verantwortlich, wenn eine fehler-

hafte Montage oder Verwendung Verlet-

zungen oder Schäden verursacht. Bewah-

ren Sie die Anleitung zusammen mit dem

Gerät für den zukünftigen Gebrauch auf.

Das Gerät darf nur von qualifizierten Kun-

dendiensttechnikern repariert werden. Ver-

wenden Sie nur Originalersatzteile.

Versuchen Sie nicht, das Gerät selbst zu re-

parieren. Dies könnte zu Verletzungen und

zur Beschädigung des Geräts führen. Wen-

den Sie sich immer an den Kundendienst.

Sicherheit von Kindern und

schutzbedürftigen Personen

Warnung! Erstickungs- und

Verletzungsgefahr oder Gefahr einer

dauerhaften Behinderung.

• Lassen Sie keine Personen (einschließlich

Kinder) mit eingeschränkten physischen,

sensorischen oder geistigen Fähigkeiten,

mangelnder Erfahrung oder mangelndem

Wissen dieses Gerät benutzen. Solche

Personen müssen von einer Person beauf-

sichtigt oder bei der Bedienung des Ge-

räts angeleitet werden, die für ihre Si-

cherheit verantwortlich ist. Lassen Sie Kin-

der nicht mit dem Gerät spielen.

• Halten Sie das Verpackungsmaterial von

Kindern fern.

• Halten Sie alle Reinigungsmittel von Kin-

dern fern.

• Halten Sie Kinder und Haustiere vom ge-

öffneten Gerät fern.

Montage

• Entfernen Sie das Verpackungsmaterial.

• Stellen Sie ein beschädigtes Gerät nicht

auf und benutzen Sie es nicht.

• Stellen Sie das Gerät nicht an einem Ort

auf, an dem die Temperatur unter 0 °C

absinken kann, und benutzen Sie das Ge-

rät nicht, wenn die Temperatur unter 0 °C

absinken könnte.

• Halten Sie sich an die mitgelieferte Mon-

tageanleitung.

• Stellen Sie sicher, dass das Gerät unter

und an angrenzenden sicheren Konstruk-

tionen montiert ist.

Wasseranschluss

• Achten Sie darauf, die Wasserschläuche

nicht zu beschädigen.

• Bevor Sie neue oder lange Zeit nicht be-

nutzte Schläuche an das Gerät anschlie-

ßen, lassen Sie Wasser durch die Schläu-

che fließen, bis es sauber austritt.

• Achten Sie darauf, dass beim ersten Ge-

brauch des Geräts keine Undichtheiten

vorhanden sind.

DEUTSCH 19

• Im Wasserzulaufschlauch befindet sich

ein Sicherheitsventil, das ein Lösen des

Schlauchs verhindert. Drücken Sie zum

Abnehmen des Schlauchs den Hebel (B)

und drehen Sie das Befestigungselement

(A) im Uhrzeigersinn.

A

B

• Der Wasserzulaufschlauch verfügt über

eine transparente Schutzhülle. Ist der

Schlauch beschädigt, wird das Wasser im

Schlauch dunkel.

• Ziehen Sie sofort den Netzstecker aus der

Steckdose, wenn der Wasserzulauf-

schlauch beschädigt ist. Wenden Sie sich

für den Austausch des Wasserzulauf-

schlauchs an den Kundendienst.

Elektrischer Anschluss

Warnung! Brand- und

Stromschlaggefahr.

• Das Gerät muss geerdet sein.

• Stellen Sie sicher, dass die elektrischen

Daten auf dem Typenschild den Daten

Ihrer Stromversorgung entsprechen.

Wenden Sie sich andernfalls an eine

Elektrofachkraft.

• Das Gerät darf ausschließlich an eine

ordnungsgemäß installierte Schutzkon-

taktsteckdose angeschlossen werden.

• Verwenden Sie keine Mehrfachsteckdo-

sen oder Verlängerungskabel.

• Achten Sie darauf, Netzstecker und Netz-

kabel nicht zu beschädigen. Wenden Sie

sich zum Austausch des beschädigten

Netzkabels an den Kundendienst oder

eine Elektrofachkraft.

• Stecken Sie den Netzstecker erst nach

Abschluss der Montage in die Steckdose.

Stellen Sie sicher, dass der Netzstecker

nach der Montage noch zugänglich ist.

• Ziehen Sie nicht am Netzkabel, um das

Gerät von der Spannungsversorgung zu

trennen. Ziehen Sie dazu immer direkt am

Netzstecker.

•

Das Gerät entspricht den EC-Richtlinien.

Gebrauch

• Dieses Gerät ist für die Verwendung im

Haushalt und ähnliche Zwecke vorgese-

hen, wie z. B.:

– Personalküchenbereiche in Geschäften,

Büros und anderen Arbeitsumfeldern

– Bauernhöfe

– Für Gäste in Hotels, Motels und ande-

ren wohnungsähnlichen Räumlichkeiten

– In Pensionen und vergleichbaren Un-

terbringungsmöglichkeiten.

Warnung! Verletzungsgefahr.

• Nehmen Sie keine technischen Änderun-

gen am Gerät vor.

• Stellen Sie Messer und Besteck mit schar-

fen Spitzen mit der Spitze nach unten in

den Besteckkorb oder legen Sie sie in ei-

ne waagerechte Position.

• Lassen Sie die Gerätetür nicht ohne Be-

aufsichtigung offen stehen, damit von der

Tür keine Stolpergefahr ausgeht.

• Setzen oder stellen Sie sich nie auf die of-

fene Tür.

• Geschirrspüler-Reinigungsmittel sind ge-

fährlich. Beachten Sie die Sicherheitsan-

weisungen auf der Reinigungsmittelver-

packung.

• Trinken Sie nicht das Wasser aus dem

Gerät und verwenden Sie es nicht zum

Spielen.

• Nehmen Sie kein Geschirr aus dem Ge-

rät, bevor das Programm beendet ist. Es

könnte sich noch Reinigungsmittel auf

dem Geschirr befinden.

Warnung! Stromschlag-, Brand- und

Verbrennungsgefahr.

DEUTSCH 20

La page charge ...

IKEA LAGAN Manuel utilisateur

IKEA LAGAN Manuel utilisateur

dans d''autres langues

Documents connexes