Dell W-IAP214/215 Le manuel du propriétaire

Marque: Dell

Modèle: W-IAP214/215

Catégorie: Points d'accès WLAN

Taper: Le manuel du propriétaire

Dell Networking W-IAP210 Series Wireless Instant Access Point

Installation Guide

Dell Networking W-IAP210 Series (W-IAP214 and W-IAP215) wireless Instant Access

Points (IAP) supports IEEE 802.11n standard for high-performance WLAN. It uses

MIMO (Multiple-Input, Multiple-Output) technology and other high-throughput

mode techniques to deliver high-performance, 802.11n 2.4 GHz and 802.11ac 5 GHz

functionality while simultaneously supporting existing 802.11a/b/g wireless services.

The W-IAP210 Series Instant access points works only in conjunction with a virtual

controller.

The W-IAP210 Series Instant access point provides the following capabilities:

 Wireless transceiver

 Protocol-independent networking functionality

 IEEE 802.11a/b/g/n/ac operation as a wireless access point

 IEEE 802.11a/b/g/n/ac operation as a wireless air monitor

 Compatibility with IEEE 802.3at PoE+ and 802.3af PoE

Package Contents

 W-IAP214 or W-IAP215 Instant Access Point

 9/16" and 15/16” Ceiling Rail Adapters

 Quick Start Guide

 Installation Guide (this document)

W-IAP210 Series Hardware Overview

Figure 1

W-IAP210 Series LEDs

LEDs

The W-IAP210 Series is equipped with four LEDs that indicate the status of its various

components.

 PWR: Indicates whether or not the IAP is powered-on

 ENET: Indicates the status of the IAP’s Ethernet port

 5 GHz: Indicates the status of the IAP 802.11a/n radio

 2.4 GHz: Indicates the status of the IAP 802.11b/g/n radio

Figure 2

W-IAP210 Series Side View (W-IAP214 shown)

External Antenna Connectors

The W-IAP214 Instant access point is equipped with three external antenna

connectors. The connectors are labeled ANT0, ANT1, and ANT2, and correspond to

radio chains 0, 1, and 2.

USB Interface

The W-IAP210 Series Instant access point is equipped with a USB interface for

connectivity with cellular modems.

Figure 3

W-IAP210 Series Rear View

Console Port

The serial console port allows you to connect the IAP to a serial terminal or a laptop for

direct local management. This port comprises of an RJ-45 female connector with the

pinouts described in Figure 4. Connect it directly to a terminal or terminal server using

an Ethernet cable.

Figure 4

Serial Port Pin-Out

Ethernet Port

The W-IAP210 Series Instant access point is equipped with one 10/100/1000Base-T

(RJ-45) auto-sensing, MDI/MDX wired-network connectivity port. This port supports

IEEE 802.3af and 802.3at Power over Ethernet (PoE) compliance, accepting 48 VDC

(nominal) as a standard defined Powered Device (PD) from a Power Sourcing

Equipment (PSE) such as a PoE midspan injector, or network infrastructure that

supports PoE.

The port comprises of an RJ-45 female connector with the pin-outs shown in

Figure 5.

Figure 5

Gigabit Ethernet Port Pin-Out

DC Power Socket

If PoE is not available, an optional Dell AP/IAP AC-DC adapter kit (sold separately)

can be used to power the IAP.

Additionally, a locally-sourced AC-to-DC adapter (or any DC source) can be used to

power this device, as long as it complies with all applicable local regulatory

requirements and the DC interface meets the following specifications:

 12 VDC (+/- 5%)/18W

 Center-positive 1.7/4.0 mm circular plug, 9.5 mm length

Reset Button

The reset button can be used to return the IAP to factory default settings. To reset the

IAP:

1. Power off the IAP.

2. Press and hold the reset button using a small, narrow object, such as a paperclip.

3. Power-on the IAP without releasing the reset button. The power LED will flash

within 5 seconds.

4. Release the reset button.

The power LED will flash again within 15 seconds indicating that the reset is

completed. The IAP will now continue to boot with the factory default settings.

Before You Begin

Pre-Installation Checklist

Before installing the W-IAP210 Series Instant access point, ensure that you have the

following:

 CAT5e or better UTP cable of required length

 One of the following power sources:

 IEEE 802.3at or 802.3af-compliant Power over Ethernet (PoE) source. The POE

source can be any power source equipment (PSE) virtual controller or midspan

PSE device

 Dell AP AC-DC adapter kit (sold separately)

Summary of the Setup Process

Successful setup of a W-IAP210 Series Instant access point consists of four tasks, which

must be performed in this order:

1. Verify pre-installation connectivity.

2. Identify the specific installation location for each IAP.

3. Install each IAP.

4. Configure the virtual controller. Refer to the Dell Networking W-Series Instant

Quick Start Guide

Identifying Specific Installation Locations

You can mount the W-IAP210 Series Instant access point on a wall or on the ceiling.

Use the AP/IAP placement map generated by Dell Airwave VisualRF Plan software

application to determine the proper installation location(s). Each location should be as

close as possible to the center of the intended coverage area and should be free from

obstructions or obvious sources of interference. These RF absorbers/reflectors/

interference sources will impact RF propagation and should have been accounted

during the planning phase and adjusted in the VisualRF plan.

Identifying Known RF Absorbers/Reflectors/Interference Sources

Identifying known RF absorbers, reflectors, and interference sources while in the field

during the installation phase is critical. Make sure that these sources are taken into

consideration when you attach an AP to its fixed location. Examples of sources that

degrade RF performance include:

 Cement and brick

 Objects that contain water

 Metal

 Microwave ovens

 Wireless phones and headsets

Installing the IAP

Using the Ceiling Rail Adapter

The W-IAP210 Series Instant access point ships with two ceiling rail adapters for 9/16”

and 15/16” ceiling rails. Additional wall mount adapters and ceiling rail adapters for

other rail styles are available as accessory kits.

1. Pull the necessary cables through a prepared hole in the ceiling tile where the IAP

will be placed.

2. Place the adapter against the back of the IAP at an angle of approximately 30

degrees to the tabs (see Figure 6).

3. Twist the adapter clockwise until it snaps into place in the tabs (see Figure 6).

Figure 6

Attaching the Ceiling Rail Adapter

Note: The W-IAP210 Series requires Dell Instant 4.1.1 or later.

Note: Inform your supplier if there are any incorrect, missing, or damaged parts. If

possible, retain the carton, including the original packing materials. Use these

materials to repack and return the unit to the supplier if needed.

LED Color/State Meaning

PWR Off No power to IAP

Red Initial power-up

Green - Flashing IAP booting

Green - Steady IAP ready

ENET Off Ethernet link unavailable

Yellow - Steady 10/100Mbps Ethernet link established

Green - Steady 1000Mbps Ethernet link established

Flashing Ethernet link activity

5 GHz Off 5 GHz radio disabled

Yellow - Steady 5 GHz radio enabled in non-HT WLAN mode

Green - Steady 5 GHz radio enabled in HT WLAN mode

Flashing - Green 5 GHz Air or Spectrum Monitor

2.4 GHz Off 2.4 GHz radio disabled

Yellow - Steady 2.4 GHz radio enabled in non-HT WLAN mode

Green - Steady 2.4 GHz radio enabled in HT WLAN mode

Flashing - Green 2.4 GHz Air or Spectrum Monitor

2.4Ghz

5Ghz

Note: The USB interface is disabled when the W-IAP210 Series Instant access

point is powered from 802.3af PoE.

ANT2

ANT0

ANT1

USB Port

Serial

Console Port

TxD

GND

RxD

RJ-45 Female

Pin-Out

Direction

Input

Output

GND

Caution: FCC Statement: Improper termination of access points installed in the

United States (non-US model Regulatory Domain model/s) will be in violation of

the FCC grant of equipment authorization. Any such willful or intentional violation

may result in a requirement by the FCC for immediate termination of operation and

may be subject to forfeiture (47 CFR 1.80).

Caution: EU Statement:

Lower power radio LAN product operating in 2.4 GHz and 5 GHz bands. Please

refer to the

Dell Networking W-Series Instant User Guide

for details on

restrictions.

Produit réseau local radio basse puissance operant dans la bande fréquence 2.4

GHz et 5 GHz. Merci de vous referrer au

Dell Networking W-Series Instant User

Guide

pour les details des restrictions.

Low Power FunkLAN Produkt, das im 2.4 GHz und im 5 GHz Band arbeitet. Weitere

Informationen bezlüglich Einschränkungen finden Sie im

Dell Networking W-

Series Instant User Guide.

Apparati Radio LAN a bassa Potenza, operanti a 2.4 GHz e 5 GHz. Fare riferimento

alla

Dell Networking W-Series Instant User Guide

per avere informazioni

detagliate sulle restrizioni.

1000Base-T Gigabit

Ethernet Port

RJ-45 Female

Pin-Out

Signal Name

BI_DC+

BI_DC-

BI_DD+

BI_DD-

BI_DA+

BI_DA-

BI_DB+

BI_DB-

Function

Bi-directional pair +C

Bi-directional pair -C

Bi-directional pair +D

Bi-directional pair -D

Bi-directional pair +A

Bi-directional pair -A

Bi-directional pair +B

Bi-directional pair -B

Note: Dell, in compliance with governmental requirements, has designed the W-

IAP210 Series Instant access points so that only authorized network administrators

can change the settings. For more information about IAP configuration, refer to the

Dell Networking W-Series Instant Quick Start Guide

and

Dell Networking W-Series

Instant User Guide

Caution: Access points are radio transmission devices and as such are subject

to governmental regulation. Network administrators responsible for the

configuration and operation of access points must comply with local broadcast

regulations. Specifically, access points must use channel assignments

appropriate to the location in which the access point will be used.

Note: Service to all Dell W-Series products should be performed by trained service

personnel only.

Caution: Make sure the IAP fits securely on the ceiling tile rail when

hanging the device from the ceiling, because poor installation could cause

it to fall on people or equipment.

AP-110_04

Dell Networking W-IAP210 Series

Wireless Instant Access Point

Installation Guide

www.dell.com

Dell Networking W-IAP210 Series Wireless Instant Access Point | Installation Guide

Part Number 0511572-01 | September 2014

Contacting Dell

Website Support

Main Website dell.com

Contact Information dell.com/contactdell

Support Website dell.com /support

Documentation Website dell.com /support/manuals

Aruba Wireless Networks

, the registered Aruba the Mobile Edge Company logo, and Aruba Mobility

Management System

. Dell™, the DELL™ logo, and PowerConnect™ are trademarks of Dell Inc.

Originated in the USA. All other trademarks are the property of their respective owners.

Open Source Code

Certain Aruba products include Open Source software code developed by third parties, including software code

subject to the GNU General Public License (GPL), GNU Lesser General Public License (LGPL), or other Open

Source Licenses. The Open Source code used can be found at this site:

http://www.arubanetworks.com/open_source

reserved. This product includes software developed by Lars Fenneberg, et al.

Legal Notice

The use of Aruba Networks, Inc. switching platforms and software, by all individuals or corporations, to terminate

other vendors’ VPN client devices constitutes complete acceptance of liability by that individual or corporation for

this action and indemnifies, in full, Aruba Networks, Inc. from any and all legal actions that might be taken against

it with respect to infringement of copyright on behalf of those vendors.

4. If necessary, connect the console cable to the console port on the back of the IAP.

5. Hold the IAP next to the ceiling tile rail with the ceiling tile rail mounting slots at

approximately a 30-degree angle to the ceiling tile rail (see Figure 7). Make sure that

any cable slack is above the ceiling tile.

6. Pushing toward the ceiling tile, rotate the IAP clockwise until the device clicks into

place on the ceiling tile rail.

Figure 7

Mounting the IAP

7. On the W-IAP214 Instant access point, install the external antennas according to the

manufacturer’s instructions, and connect the antennas to the antenna interfaces on

the IAP.

Connecting Required Cables

Install cables in accordance with all applicable local and national regulations and

practices.

Verifying Post-Installation Connectivity

The integrated LEDs on the IAP can be used to verify that the IAP is receiving power and

initializing successfully (see Table 1). Refer to the Dell Networking W-Series Instant Quick

Start Guide for further details on verifying post-installation network connectivity.

Product Specifications

Electrical

 Ethernet:

 1x 10/100/1000 auto-sensing Ethernet RJ-45 Interface

 MDI/MDX

 IEEE 802.3 (10Base-T), IEEE 802.3u (100Base-T). IEEE 802.3ab (1000Base-T)

 Power over Ethernet (IEEE 802.3at and 802.3af compliant), 48V DC (nominal)

and 56V DC (maximum)/350mA (see Figure 5 for pin configuration)

 Power:

 12 VDC power interface, supports powering through an AC-to-DC power adapter

 POE support on Ethernet ports: 802.3at-compliant and 802.3af-compliant POE

sourcing devices

For additional specifications on this product, please refer to the product data sheet on

dell.com.

Proper Disposal of Dell Equipment

Dispose Dell products per local regulations. For the most current information about

Global Environmental Compliance and Dell products, visit dell.com.

Waste of Electrical and Electronic Equipment

Dell products at end of life are subject to separate collection and

treatment in the EU Member States, Norway, and Switzerland and

therefore are marked with the symbol shown at the left (crossed-out

wheelie bin). The treatment applied at end of life of these products

in these countries shall comply with the applicable national laws of

countries implementing Directive 2002/96/EC on Waste of Electrical

and Electronic Equipment (WEEE).

European Union RoHS

Dell products comply with the EU Restriction of Hazardous

Substances Directive 2011/65/EC (RoHS). EU RoHS restricts

the use of specific hazardous materials in the manufacture of

electrical and electronic equipment. Specifically, restricted

materials under the RoHS Directive are Lead (including Solder used in printed circuit

assemblies), Cadmium, Mercury, Hexavalent Chromium, and Bromine. Some Dell

products are subject to the exemptions listed in RoHS Directive Annex 7 (Lead in solder

used in printed circuit assemblies). Products and packaging will be marked with the

“RoHS” label shown at the left indicating conformance to this Directive.

A copy of the Declaration of Conformity may be obtained upon request from:

Aruba Networks International Ltd.

Building 1000,

Citygate Mahon

Cork Ireland

Please include the regulatory model number located on the product’s regulatory

nameplate with the request.

China RoHS

Dell products comply with China environmental declaration

requirements and are labeled with the “EFUP 10” label shown at the left.

India RoHS

This product complies with RoHS requirements as prescribed by E-Waste (Management

& Handling) Rules, governed by the Ministry of Environment & Forests, Government of

India.

Safety and Regulatory Compliance

Regulatory Model Names

The following regulatory model names apply to the W-IAP210 Series Instant access point:

 W-IAP214: APIN0214

 W-IAP215: APIN0215

정소출력 무선기기 ( 무선데이터통신시스템용 무선기기 )

FCC

The device is electronically labeled and the FCC ID is displayed via the WebUI under the

About menu

FCC Class B Part 15

This device complies with Part 15 of the Federal Communications Commission (FCC)

Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may

cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the

manufacturer’s instructions, may cause interference harmful to radio communications.

If this equipment does cause interference, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and receiver.

 Connect the equipment to an outlet on a circuit different from that to which the

receiver is connected.

 Consult the dealer or an experienced radio or TV technician for help.

Complies with the Class B limits for radio noise emissions as set out in the interference-

causing equipment standard entitled “Digital Apparatus,” ICES-003 of Industry Canada.

Cet apareil numerique de la classe B respecte toutes les exigencies du Reglement sur le materiel brouilleur

du Canada.

Users are advised that high power Radars are allocated as primary users of the bands 5250-5350 MHz and

5650-5850 MHz and these Radars could cause interference and/or damage to Licensed Exempt WLAN

devices.

EU Regulatory Conformance

This product is CE marked according to the provisions of the R & TTE

Directive (1999/5/EC) - CE(!). Dell, hereby declares that the APIN0114

/ APIN0115 device models are in compliance with the essential requirements and other

relevant provisions of Directive 1999/5/EC -CE(!)

The Declaration of Conformity made under Directive 1999/5/EC is available on dell.com

Canada

(i)les dispositifs fonctionnant dans la bande 5 150-5 250 MHz sont réservés uniquement

pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux

systèmes de satellites mobiles utilisant les mêmes canaux;

(ii) le gain maximal d’antenne permis pour les dispositifs utilisant les bandes 5 250-5 350

MHz et 5 470-5 725 MHz doit se conformer à la limite de p.i.r.e.;

(iii) le gain maximal d’antenne permis (pour les dispositifs utilisant la bande 5 725-5 825

MHz) doit se conformer à la limite de p.i.r.e. spécifiée pour l’exploitation point à point et

non point à point, selon le cas.

De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute

puissance sont désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour les

bandes 5 250-5 350 MHz et 5 650-5 850 MHz et que ces radars pourraient causer du

brouillage et/ou des dommages aux dispositifs LAN-EL.

This radio transmitter 4567A-APIN0214215 has been approved by Industry Canada to

operate with the antenna types listed below with the maximum permissible gain and

required antenna impedance for each antenna type indicated. Antenna types not included

in this list, having a gain greater than the maximum gain indicated for that type, are

strictly prohibited for use with this device.

The following antenna types have been approved for use with this device:

AP-ANT-1B; AP-ANT-1W; AP-ANT-13B; AP-ANT-16; AP-ANT-17; AP-ANT-18;

AP-ANT-19; AP-ANT-20

The Maximum permissible antenna gain is 7.5dBi and the antenna impedance is 50 ohms.

Singapore

Korean EMC Class B Warning

이 기기는 가정용(B급) 전자파적합기기로서 주로 가정에서 사용하는 것을 목적으로

하며, 모든 지역에서 사용할 수 있습니다.

Medical

1. Equipment not suitable for use in the presence of flammable mixtures.

2. Connect to only IEC 60950-1 or IEC 60601-1 3rd edition certified products and power

sources. The end user is responsible for the resulting medical system complies with the

requirements of IEC 60601-1 3rd edition.

3. Wipe with a dry cloth, no additional maintenance required.

4. No serviceable parts, the unit must be sent back to the manufacturer for repair.

5. No modifications are allowed without Dell approval.

第十二條

　　經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自

變更頻率、加大功率或變更原設計之特性及功能。

第十四條

　　低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有

干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。

　　前項合法通信，指依電信法規定作業之無線電通信。

　　低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電

機設備之干擾。

Note: If a power adapter other than the one provided by Dell is used in the US or

Canada, it should be cULus (NRTL) Listed, with an output rated 12 VDC, minimum

1.5A, marked “LPS” or “Class 2,” and suitable for plugging into a standard power

receptacle in the US and Canada.

AP-110_005

Note: For country specific restrictions and additional safety and regulatory

information, refer to the multi-language

Dell Networking W-Series Safety,

Environmental, and Regulatory Information

document included with this product

Caution: Dell Instant access points must be installed by a professional installer.

The professional installer is responsible for ensuring that grounding is available

and it meets applicable local and national electrical codes.

Caution: RF Radiation Exposure Statement: This equipment complies with FCC RF

radiation exposure limits. This equipment should be installed and operated with a

minimum distance of 7.9 inches (20 cm) between the radiator and your body for

2.4 GHz and 5 GHz operations. This transmitter must not be co-located or

operating in conjunction with any other antenna or transmitter. When operated in

the 5.15 to 5.25 GHz frequency range, this device is restricted to indoor use to

reduce the potential for harmful interference with co-channel Mobile Satellite

Systems.

Caution: Changes or modifications to this unit not expressly approved by the party

responsible for compliance could void the user’s authority to operate this

equipment.

᳝↦᳝ᆇ⠽䋼ໄᯢ

Hazardous Materials Declaration

᳝↦᳝ᆇ⠽䋼៪ܗ㋴(Hazardous Substance)

䚼ӊৡ⿄

(Parts)

䪙

3E

∲

+J

䬝

&G

݁Ӌ䫀

&U





໮⒈㘨㣃

3%%

໮⒈Ѡ㣃䝮

3%'(

⬉䏃ᵓ

(PCA Boards)

hƻ ƻ ƻ ƻ ƻ

ᴎẄ㒘ӊ

(Mechanical Sub-Assemblies)

hƻ ƻ ƻ ƻ ƻ



ƻ˖

㸼⼎䆹᳝↦᳝ᆇ⠽䋼೼䆹䚼ӊ᠔᳝ഛ䋼ᴤ᭭Ёⱘ৿䞣ഛ೼

SJ/T11363-2006 ᷛޚ㾘ᅮⱘ䰤䞣㽕∖ҹϟǄ

Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is

below the relevant threshold of the SJ/T11363-2006 standard.



h˖ 㸼⼎䆹᳝↦᳝ᆇ⠽䋼㟇ᇥ೼䆹䚼ӊⱘᶤϔഛ䋼ᴤ᭭Ёⱘ৿䞣䍙ߎ6-7ᷛޚ㾘ᅮⱘ䰤䞣㽕∖Ǆ

Indicates that the concentration of the hazardous substance of at least one of all homogeneous materials

in the parts is above the relevant threshold of the SJ/T11363-2006 standard.



ᇍ䫔ଂП᮹ⱘ᠔ଂѻકᴀ㸼ᰒ⼎կᑨ䫒ⱘ⬉ᄤֵᙃѻકৃ㛑ࣙ৿䖭ѯ⠽䋼Ǆ

This table shows where these substances may be found in the supply chain of electronic information

products, as of the date of sale of the enclosed product.

ℸᷛᖫЎ䩜ᇍ᠔⍝ঞѻકⱘ⦃ֱՓ⫼ᳳᷛᖫᶤѯ䳊䚼ӊӮ᳝ϔϾϡৠⱘ⦃ֱՓ⫼ᳳ

՟བ⬉∴ऩܗ῵ഫ䌈೼݊ѻકϞ

ℸ⦃ֱՓ⫼ᳳ䰤া䗖⫼Ѣѻકᰃ೼ѻક᠟ݠЁ᠔㾘ᅮⱘᴵӊϟᎹ԰

The Environment- Friendly Use Period (EFUP) for all enclosed products and their parts are

per the symbol shown here. The Environment- Friendly Use Period is valid only when the

product is operated under the conditions defined in the product manual.

Note: Aucune émission n’est permise dans la bande 5 600-5 650 MHz. Jusqu’à

nouvel avis, les dispositifs visés par la présente annexe ne doivent pas être en

mesure d’émettre dans la bande 5 600-5 650 MHz, afin de protéger les radars

météorologiques d’Environnement Canada exploités dans cette bande.

Caution: RF Déclaration sur la radioexposition: Cet équipement est conforme aux

normes IC Limites d'exposition aux rayonnements RF. Cet équipement doit être

installé et utilisé à une distance minimum de 7,9 pouces (20 cm) entre l'radiateur et

votre corps pour 2,4 GHz et 5 GHz opérations. cet émetteur ne doit pas être co-

localisées ou opérant en conjonction avec une autre antenne ou émetteur.

DB101525

Dell W-IAP214/215 Le manuel du propriétaire

Marque: Dell

Modèle: W-IAP214/215

Catégorie: Points d'accès WLAN

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Dell W-IAP214/215 Owner's manual

Dell W-IAP214/215 Le manuel du propriétaire

Dell W-IAP214/215 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents