Simplicity 030253-0 Manuel utilisateur

Marque: Simplicity

Modèle: 030253-0

Catégorie: Groupes électrogènes

Taper: Manuel utilisateur

Ce manuel convient également à

30253

Model / Modèle / Modelo

030253

Operator’s Manual

Manuel d’utilisation

Manual del Operario

Questions? Help is just a moment away!

Vous avez des questions? Vous n'avez pas besoin

d'aller loin pour trouver de l'aide!

Preguntas? La ayuda es justa un momento lejos!

Call: Generator Helpline

Appelez: Ligne d'assistance de Générateur

Llame: Línea Directa del Generador

1-800-743-4115 M-F 8-5 CT

web: www.briggsandstratton.com

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC

JEFFERSON,WISCONSIN, U.S.A.

Manual No. 198171GS

Revision 1 (11/14/2005)

Before using this product, read this

manual and follow all Safety Rules and

Operating Instructions.

WARNING

Antes de utilizar el producto, lea este

manual y siga todas las Reglas de

Seguridad e Instrucciones de Uso.

ADVERTENCIA

Avant d’utiliser ce produit, veuillez lire

le manuel et suivre toutes les directives

relatives à la sécurité et à l’utilisation.

AVERTISSEMENT

SAFETY RULES

TABLE OF CONTENTS

Safety Rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

Know Your Generator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-12

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

EQUIPMENT

DESCRIPTION

Read this manual carefully and become

familiar with your generator. Know its

applications, its limitations and any hazards

involved.

The generator is an engine–driven, revolving field,

alternating current (AC) generator. It was designed to

supply electrical power for operating compatible electrical

lighting, appliances, tools and motor loads.The generator’s

revolving field is driven at about 3,600 rpm by a single-

cylinder engine.

CAUTION! DO NOT exceed the generator’s

wattage/amperage capacity. See “Don’t Overload

Generator”.

Every effort has been made to ensure that information in

this manual is accurate and current. However, we reserve

the right to change, alter or otherwise improve the product

and this document at any time without prior notice.

The Emission Control System for this generator is

warranted for standards set by the Environmental

Protection Agency and the California Air Resources Board.

For warranty information refer to the engine operator’s

manual.

SAFETY RULES

This is the safety alert symbol. It is used to

alert you to potential personal injury hazards.

Obey all safety messages that follow this

symbol to avoid possible injury or death.

The safety alert symbol ( ) is used with a signal word

(DANGER, CAUTION,WARNING), a pictorial and/or a

safety message to alert you to hazards. DANGER indicates

a hazard which, if not avoided, will result in death or serious

injury. WARNING indicates a hazard which, if not avoided,

could result in death or serious injury. CAUTION

indicates a hazard which, if not avoided, might result in

minor or moderate injury. CAUTION, when used

without the alert symbol, indicates a situation that could

result in equipment damage. Follow safety messages to

avoid or reduce the risk of injury or death.

Hazard Symbols and Meanings

The engine exhaust from this product contains

chemicals known to the State of California to cause

cancer, birth defects, or other reproductive harm.

WARNING

Fire

Explosion

Toxic Fumes

Hot Surface

Electrical Shock

Kickback

may be reproduced or transmitted in any form by any

means without the express written permission of Briggs &

Stratton Power Products Group, LLC.

SAVE THESE INSTRUCTIONS

SAFETY RULES

• This generator does not meet U. S. Coast Guard Regulation

33CFR-183 and should not be used on marine applications.

• Failure to use the appropriate U. S. Coast Guard approved

generator could result in death or serious injury and/or

property damage.

WARNING

• When using generator for backup power, notify utility

company. Use approved transfer equipment to isolate

generator from electric utility.

• Use a ground fault circuit interrupter (GFCI) in any damp or

highly conductive area, such as metal decking or steel work.

• DO NOT touch bare wires or receptacles.

• DO NOT use generator with electrical cords which are worn,

frayed, bare or otherwise damaged.

• DO NOT operate generator in the rain or wet weather.

• DO NOT handle generator or electrical cords while standing

in water, while barefoot, or while hands or feet are wet.

• DO NOT allow unqualified persons or children to operate or

service generator.

Generator produces powerful voltage.

Failure to isolate generator from power utility

can result in death or injury to electric utility

workers due to backfeed of electrical energy.

WARNING

• Operate generator ONLY outdoors.

• Keep exhaust gas from entering a confined area through

windows, doors, ventilation intakes or other openings.

• DO NOT operate generator inside any building or enclosure

(even if doors or windows are open), including the generator

compartment of a recreational vehicle (RV).

Running generator gives off carbon monoxide,

an odorless, colorless, poison gas.

Breathing carbon monoxide can cause nausea,

fainting or death.

WARNING

WHEN ADDING OR DRAINING FUEL

• Turn generator OFF and let it cool at least 2 minutes before

removing fuel cap. Loosen cap slowly to relieve pressure in

tank.

• Fill or drain fuel tank outdoors.

• DO NOT overfill tank.Allow space for fuel expansion.

• Keep fuel away from sparks, open flames, pilot lights, heat, and

other ignition sources.

• DO NOT light a cigarette or smoke.

WHEN STARTING EQUIPMENT

• Ensure spark plug, muffler, fuel cap and air cleaner are in place.

• DO NOT crank engine with spark plug removed.

• If fuel spills, wait until it evaporates before starting engine.

WHEN OPERATING EQUIPMENT

• Do not tip engine or equipment at angle which causes fuel to

spill.

• This generator is not for use in mobile equipment or marine

applications.

WHEN TRANSPORTING OR REPAIRING

EQUIPMENT

• Transport/repair with fuel tank EMPTY or with fuel shutoff

valve OFF.

• Disconnect spark plug wire.

WHEN STORING FUEL OR EQUIPMENT WITH FUEL

IN TANK

• Store away from furnaces, stoves, water heaters, clothes

dryers or other appliances that have pilot light or other

ignition source because they can ignite fuel vapors.

Fuel and its vapors are extremely flammable and

explosive.

Fire or explosion can cause severe burns or

death.

WARNING

• When starting engine, pull cord slowly until resistance is felt

and then pull rapidly to avoid kickback.

• NEVER start or stop engine with electrical devices plugged in

and turned on.

Rapid retraction of starter cord (kickback) will

pull hand and arm toward engine faster than

you can let go.

Broken bones, fractures, bruises or sprains could

result.

WARNING

SAFETY RULES

• DO NOT tamper with governed speed. Generator supplies

correct rated frequency and voltage when running at governed

speed.

• DO NOT modify generator in any way.

Excessively high operating speeds increase risk of injury

and damage to generator.

Excessively low speeds impose a heavy load.

CAUTION

• See “Don’t Overload Generator”.

• Start generator and let engine stabilize before connecting

electrical loads.

• Connect electrical loads in OFF position, then turn ON for

operation.

• Turn electrical loads OFF and disconnect from generator

before stopping generator.

Exceeding generators wattage/amperage capacity can

damage generator and/or electrical devices connected

to it.

CAUTION

• Use generator only for intended uses.

• If you have questions about intended use, ask dealer or call

1-800-743-4115.

• Operate generator only on level surfaces.

• DO NOT expose generator to excessive moisture, dust, dirt,

or corrosive vapors.

• DO NOT insert any objects through cooling slots.

• If connected devices overheat, turn them off and disconnect

them from generator.

• Shut off generator if:

-electrical output is lost;

-equipment sparks, smokes, or emits flames;

-unit vibrates excessively.

Improper treatment of generator can damage it and

shorten its life.

CAUTION

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR

GENERATOR

• Disconnect the spark plug wire from the spark plug and place

the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

• Use approved spark plug tester.

• DO NOT check for spark with spark plug removed.

Unintentional sparking can result in fire or

electric shock.

WARNING

• DO NOT touch hot surfaces and avoid hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5 ft. (152 cm) clearance on all sides of generator

including overhead.

• Code of Federal Regulation (CFR) Title 36 Parks, Forests, and

Public Property require equipment powered by an internal

combustion engine to have a spark arrester, maintained in

effective working order, complying to USDA Forest service

standard 5100-1C or later revision. In the State of California a

spark arrester is required under section 4442 of the California

Public resources code. Other states may have similar laws.

Running engines produce heat.Temperature of

muffler and nearby areas can reach or exceed

150°F (65°C).

Severe burns can occur on contact.

Exhaust heat/gases can ignite combustibles,

structures or damage fuel tank causing a fire.

WARNING

KNOW YOUR GENERATOR

Read this Operator’s Manual and safety rules before operating your generator.

Compare the illustrations with your generator, to familiarize yourself with the locations of various controls and

adjustments. Save this manual for future reference.

120 Volt AC, 20 Amp

Duplex Receptacle

Removable Fuel Tank

Choke Lever

Recoil Starter

Rocker Switch

Circuit Breakers

(AC)

120/240 Volt AC,

30 Amp Receptacle

Air Cleaner

Grounding Fastener

Oil Fill Cap/Dipstick

Vent Knob

120 Volt AC, 20 Amp, Duplex Receptacle — May be

used to supply electrical power for the operation of

120 Volt AC, 20 Amp, single phase, 60 Hz electrical lighting,

appliance, tool and motor loads.

120/240 Volt AC, 30 Amp Locking Receptacle — May

be used to supply electrical power for the operation of

120 and/or 240 Volt AC, 30 Amp, single phase, 60 Hz

electrical lighting, appliance, tool and motor loads.

Air Cleaner — Protects engine by filtering dust and

debris out of intake air.

Choke Lever — Used when starting a cold engine.

Circuit Breakers (AC) — Each receptacle is provided

with a "push to reset" circuit breaker to protect the

generator against electrical overload.

Grounding Fastener — Consult your local agency having

jurisdiction for grounding requirements in your area.

Oil Fill Cap/Dipstick — Check and add oil to engine

here.

Recoil Starter — Used to start the engine.

Removable FuelTank — Capacity of five (5) U.S. gallons.

Easily removed for convenient refueling.

Rocker Switch — Set this switch to "On" before using

recoil starter. Set switch to "Off" to switch OFF engine.

Serial Number Label — Provides model, revision and

serial number of generator. Please have these readily

available when calling for assistance.

Vent Knob — Must be open when generator is running.

Serial Number Label

ASSEMBLY

Your generator requires some assembly and is ready for

use after it has been properly serviced with the

recommended oil and fuel.

If you have any problems with the assembly of your

generator, please call the generator helpline at

1-800-743-4115. If calling for assistance, please have the

model, revision, and serial number from the serial number

label available. See “Know Your Generator” for location.

Unpacking the Generator

1. Set the carton on a rigid flat surface.

2. Remove everything from carton except generator.

3. Open carton completely by cutting each corner from

top to bottom.

4. Leave generator on carton to install handle.

Attach Handle to Unit

1. Place handle assembly onto handle supports connected

to main unit. Make sure holes in handle align with holes

on handle supports (Figure 1).

NOTE: It may be necessary to move the handle supports

from side to side in order to align the handle so it will slide

over the handle supports.

2. Insert carriage bolts through holes from outside of the

unit and attach a plastic knob from inside of unit

(Figure 2).Tighten by hand.

BEFORE STARTING THE

ENGINE

Add Engine Oil

• Place generator on a level surface.

• Use a long neck funnel OR remove the fuel tank as

described in “Fuel Tank”, when adding or changing oil.

• Refer to engine operator’s manual and follow oil

recommendations and instructions.

NOTE: Check oil often during engine break–in. Refer to

engine operator’s manual for recommendations.

NOTE: The generator assembly rotates on a prelubricated

and sealed ball bearing that requires no additional

lubrication for the life of the bearing.

Align Holes

Handle

Supports

Figure 1 — Attach Handle to Base

Figure 2 — Secure Handle

CAUTION

• Refer to engine operator’s manual for oil and fuel fill

information.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

Any attempt to crank or start the engine before it has

been properly filled with the recommended oil will result

in equipment failure.

ASSEMBLY

Add Fuel

NOTE: This gasoline engine is certified to operate on

gasoline. Exhaust Emission Control System: EM (Engine

Modifications).

1. Use clean, fresh, regular UNLEADED fuel with a

minimum of 85 octane. DO NOT use fuel which

contains Methanol. DO NOT mix oil with fuel.

2. Clean area around fuel fill cap, remove cap.

3. Slowly add regular unleaded fuel to fuel tank. Be careful

not to overfill.Allow about 1.5" of tank space for fuel

expansion (Figure 3).

4. Install fuel cap and wipe up any spilled fuel.

Fuel Tank

As is common with all plastic fuel containers, the

removable fuel tank supplied with this generator may swell

or expand due to build-up of fuel vapors when the vent

knob is closed.This tank is designed and has been tested to

safely withstand pressure-buildup.The 'ballooning' condition

is relieved by turning the vent knob fully counterclockwise

or loosening and retightening the fuel cap/gauge.When

installing the tank on your generator, relieve tank pressure

before tightening the four large plastic wing nuts.

1. Turn the vent knob fully clockwise on the fuel gauge to

close it (Figure 4).

IMPORTANT: The vent knob should be closed whenever

you move the generator or transport the fuel tank.

WHEN ADDING FUEL

• Turn generator OFF and let it cool at least 2 minutes before

removing fuel cap. Loosen cap slowly to relieve pressure in tank.

• Fill fuel tank outdoors.

• Fuel tank must be lying flat when filling, any other position may

cause fuel to spill.

• DO NOT overfill tank.Allow space for fuel expansion.

• Keep fuel away from sparks, open flames, pilot lights, heat, and

other ignition sources.

• DO NOT light a cigarette or smoke.

Fuel and its vapors are extremely flammable and

explosive.

Fire or explosion can cause severe burns or

death.

WARNING

Figure 4 — Vent Knob

Vent Knob

Fuel

Tank

1.5” Air Space

Figure 3 - Fuel Expansion

AVOID SPILLING FUEL WHILE REMOVING FUEL

TANK

• Turn generator OFF and let it cool at least 2 minutes before

removing fuel tank. Loosen fuel gauge slowly or open vent

knob to relieve pressure in tank.

• Tighten fuel gauge and close vent knob.

• Turn fuel shut off valve to the “Off” position.

• Disconnect the quick connect on the fuel line.

• Remove the four plastic fuel tank wing nuts.

• Lift fuel tank straight up.

Fuel and its vapors are extremely flammable and

explosive.

Fire or explosion can cause severe burns or

death.

WARNING

ASSEMBLY

2. Turn the fuel shut off valve to the “Off” position

(Figure 5).

3. Disconnect the quick connect on the fuel line by

pushing on the metal tab and twisting apart (Figure 6).

Release the metal tab. Some fuel that is left in the line

will spill out.

4. Remove the four large plastic wing nuts holding the

tank onto the frame by turning them counter-

clockwise (Figure 7).

5. Lift off the fuel tank by grasping the handle (provided

on the tank) with one hand and putting the other hand

in the finger pocket (Figure 8). Lift the tank straight up.

IMPORTANT:The fuel tank MUST be filled with it lying

flat, not slanted or standing upright (Figure 9). DO NOT let

the fuel valve and quick connect come in contact with any

dirt.

To place the fuel tank back on the unit, follow these same

steps in reverse order. Make sure the four large plastic wing

nuts are tightened securely.

IMPORTANT: Remove any dirt found inside the quick

connect before putting the fuel tank back on the unit.

Make sure the vent knob is turned fully counter-

clockwise to open it. If you don’t open it, fuel will not

flow into the fuel line causing the unit to not start.

Figure 5 — Fuel Shut-off Valve

Fuel Valve is shown

in the “Off” position

Fuel Tank

Figure 6 — Quick Connect

Figure 7 — Plastic Tank Wing Nuts

Figure 8 — Lifting Off Fuel Tank

Figure 9 — Fuel Tank

OPERATION

USING THE GENERATOR

System Ground

The generator has a system ground that connects the

generator frame components to the ground terminals on

the AC output receptacles.The system ground is connected

to the AC neutral wire (the neutral is bonded to the

generator frame).

Special Requirements

There may be Federal or State Occupational Safety and

Health Administration (OSHA) regulations, local codes, or

ordinances that apply to the intended use of the generator.

Please consult a qualified electrician, electrical inspector, or

the local agency having jurisdiction.

• In some areas, generators are required to be registered

with local utility companies.

• If the generator is used at a construction site, there may

be additional regulations which must be observed.

Connecting to a Building’s Electrical

System

Connections for standby power to a building’s electrical

system must be made by a qualified electrician.The

connection must isolate the generator power from utility

power, and must comply with all applicable laws and

electrical codes.

Generator Location

Generator Clearance

Place generator in a well ventilated area, which will allow

for removal of deadly exhaust gas. DO NOT place

generator where exhaust gas could accumulate and enter

inside or be drawn into a potentially occupied building.

Ensure exhaust gas is kept away from any windows, doors,

ventilation intakes or other openings that can allow exhaust

gas to collect in a confined area (Figure 10). Prevailing

winds and air currents should be taken into consideration

when positioning generator.

• When using generator for backup power, notify utility

company. Use approved transfer equipment to isolate

generator from electric utility.

• Use a ground fault circuit interrupter (GFCI) in any damp or

highly conductive area, such as metal decking or steel work.

• DO NOT touch bare wires or receptacles.

• DO NOT use generator with electrical cords which are worn,

frayed, bare or otherwise damaged.

• DO NOT operate generator in the rain or wet weather.

• DO NOT handle generator or electrical cords while standing

in water, while barefoot, or while hands or feet are wet.

• DO NOT allow unqualified persons or children to operate or

service generator.

Generator produces powerful voltage.

Failure to isolate generator from power utility

can result in death or injury to electric utility

workers due to backfeed of electrical energy.

WARNING

• Operate generator ONLY outdoors.

• Keep exhaust gas from entering a confined area through

windows, doors, ventilation intakes or other openings.

• DO NOT operate generator inside any building or enclosure

(even if doors or windows are open), including the generator

compartment of a recreational vehicle (RV).

Running generator gives off carbon monoxide,

an odorless, colorless, poison gas.

Breathing carbon monoxide can cause nausea,

fainting or death.

WARNING

Figure 10 — Generator Clearance

Exhaust Port

Typical Generator Shown

• Keep at least 5 ft. (152 cm) clearance on all sides of generator

including overhead.

Exhaust heat/gases can ignite combustibles,

structures or damage fuel tank causing a fire.

WARNING

OPERATION

OPERATING THE

GENERATOR

Starting the Engine

Disconnect all electrical loads from the generator. Follow

these start instruction steps in numerical order:

1. Make sure unit is on a level surface.

IMPORTANT: Failure to start and operate unit on a level

surface will cause the unit not to start or shut down during

operation.

2. Make sure the fuel line quick connect is hooked up and

that all four tank hold-downs are firmly tight.

3. Turn the vent knob fully counter-clockwise. See

Figure 4 on page 7.

4. Rotate the fuel valve to the “On” position. See

Figure 5 on page 7.

5. Start the engine according to instructions given in the

engine operator’s manual.

NOTE: If engine starts after 3 pulls but fails to run, or if

unit shuts down during operation, make sure unit is on a

level surface and check for proper oil level in crankcase.

This unit may be equipped with a low oil protection device.

See engine operator’s manual.

Connecting Electrical Loads

• Let engine stabilize and warm up for a few minutes after

starting.

• Plug in and turn on the desired 120 and/or 240 Volt AC,

single phase, 60 Hz electrical loads.

• DO NOT connect 240 Volt loads to the 120 Volt duplex

receptacles.

• DO NOT connect 3–phase loads to the generator.

• DO NOT connect 50 Hz loads to the generator.

• DO NOT OVERLOAD THE GENERATOR. See

“Don’t Overload Generator”.

• See “Don’t Overload Generator”.

• Start generator and let engine stabilize before connecting

electrical loads.

• Connect electrical loads in OFF position, then turn ON for

operation.

• Turn electrical loads OFF and disconnect from generator

before stopping generator.

Exceeding generators wattage/amperage capacity can

damage generator and/or electrical devices connected

to it.

CAUTION

• When starting engine, pull cord slowly until resistance is felt

and then pull rapidly to avoid kickback.

• NEVER start or stop engine with electrical devices plugged in

and turned on.

Rapid retraction of starter cord (kickback) will

pull hand and arm toward engine faster than

you can let go.

Broken bones, fractures, bruises or sprains could

result.

WARNING

• DO NOT touch hot surfaces and avoid hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5 ft. (152 cm) clearance on all sides of generator

including overhead.

• Code of Federal Regulation (CFR) Title 36 Parks, Forests, and

Public Property require equipment powered by an internal

combustion engine to have a spark arrester, maintained in

effective working order, complying to USDA Forest service

standard 5100-1C or later revision. In the State of California a

spark arrester is required under section 4442 of the California

Public resources code. Other states may have similar laws.

Running engines produce heat.Temperature of

muffler and nearby areas can reach or exceed

150°F (65°C).

Severe burns can occur on contact.

Exhaust heat/gases can ignite combustibles,

structures or damage fuel tank causing a fire.

WARNING

OPERATION

Stopping the Engine

1. Turn off and unplug all electrical loads from generator

panel receptacles. NEVER start or stop engine with

electrical devices plugged in and turned on.

2. Let engine run at no–load for 30 seconds to stabilize

internal temperatures of engine and alternator.

3. Turn engine off according to instructions given in

engine operator’s manual.

4. Move fuel valve to “Off” position.

RECEPTACLES

120/240 Volt AC, 30 Amp, Locking

Receptacle

Use a NEMA L14–30 plug with this receptacle. Connect a

4–wire cord set rated for 250 Volt AC loads at 30 Amps (or

greater) (Figure 11).You can use the same 4–wire cord if

you plan to run a 120 Volt load.

This receptacle powers 120/240 Volt AC, 60 Hz, single

phase loads requiring up to 2,775 watts of power at

23.1 Amps for 120 Volts; 5,550 watts of power (5.55 kW)

at 23.1 Amps for 240 Volts.The outlet is protected by a

push–to–reset circuit breaker.

120 Volt AC, 20 Amp, Duplex

Receptacles

Each duplex receptacle (Figure 12) is protected against

overload by a push–to–reset circuit breaker.

Use each receptacle to operate 120 Volt AC, single–phase,

60 Hz electrical loads requiring up to 2,400 watts (2.4 kW)

at 20 Amps of current. Use cord sets that are rated for

125 Volt AC loads at 20 Amps (or greater).

Figure 12 — 120 Volt, 20 Amp Duplex Receptacle

• NEVER attempt to power a device requiring more amperage

than generator or receptacle can supply.

• DO NOT overload the generator. See “Don’t Overload

Generator”.

Receptacles may be marked with rating value greater

than generator output capacity.

CAUTION

Figure 11 — 120/240 Volt AC, 30 Amp Receptacle

4-Wire Cord Set

240V

120V

W (Neutral)

X (Hot)

Y (Hot)

NEMA L14-30

Ground (Green)

OPERATION

DON'T OVERLOAD

GENERATOR

Capacity

You must make sure your generator can supply enough

rated (running) and surge (starting) watts for the items you

will power at the same time. Follow these simple steps:

1. Select the items you will power at the same time.

2. Total the rated (running) watts of these items.This is

the amount of power your generator must produce to

keep your items running. See Figure 13.

3. Estimate how many surge (starting) watts you will

need. Surge wattage is the short burst of power

needed to start electric motor-driven tools or

appliances such as a circular saw or refrigerator.

Because not all motors start at the same time, total

surge watts can be estimated by adding only the

item(s) with the highest additional surge watts to the

total rated watts from step 2.

Example:

Total Rated (Running) Watts = 3075

Highest Additional Surge Watts = 1800

Total Generator Output Required = 4875

Power Management

To prolong the life of your generator and attached devices,

it is important to take care when adding electrical loads to

your generator.There should be nothing connected to the

generator outlets before starting it's engine.The correct

and safe way to manage generator power is to sequentially

add loads as follows:

1. With nothing connected to the generator, start the

engine as described in this manual.

2. Plug in and turn on the first load, preferably the largest

load you have.

3. Permit the generator output to stabilize (engine runs

smoothly and attached device operates properly.

4. Plug in and turn on the next load.

5. Again, permit the generator to stabilize.

6. Repeat steps 4 and 5 for each additional load.

NEVER add more loads than the generator capacity.Take

special care to consider surge loads in generator capacity,

as described above.

*Wattages listed are approximate only. Check tool or

appliance for actual wattage.

Tool or Appliance

Rated (Running)

Watts

Additional Surge

(Starting) Watts

Window Air

Conditioner

1200 1800

Refrigerator 800 1600

Deep Freezer 500 500

Television 500 -

Light (75 Watts) 75 -

3075 Total

Running Watts

1800 Highest

Surge Watts

Tool or Appliance

Rated*

(Running)

Watts

Additional

Surge

(Starting)

Watts

Essentials

Light Bulb - 75 watt

Deep Freezer

500

Sump Pump

800

1200

Refrigerator/Freezer - 18 Cu. Ft.

800

1600

Water Well Pump - 1/3 HP

1000

2000

Heating/Cooling

Window AC - 10,000 BTU

1200

1800

Window Fan

300

600

Furnace Fan Blower - 1/2 HP

800

1300

Kitchen

Microwave Oven - 1000 Watt

1000

Coffee Maker

1500

Electric Stove - Single Element

1500

Hot Plate

2500

Family Room

DVD/CD Player

100

VCR

100

Stereo Receiver

450

Color Television - 27”

500

Personal Computer w/17” monitor

800

Other

Security System

180

AM/FM Clock Radio

300

Garage Door Opener - 1/2 HP

480

520

Electric Water Heater - 40 Gallon

4000

DIY/Job Site

Quartz Halogen Work Light

1000

Airless Sprayer - 1/3 HP

600

1200

Reciprocating Saw

960

Electric Drill - 1/2 HP

1000

Circular Saw - 7 1/4”

1500

Miter Saw - 10”

1800

Table Planer - 6”

1800

Table Saw/Radial Arm Saw - 10”

2000

Air Compressor - 1-1/2 HP

2500

Figure 13 - Wattage Reference Chart

SPECIFICATIONS AND MAINTENANCE

SPECIFICATIONS

Starting Wattage . . . . . . . . . . . . . . . . . . . . . . .8,550 watts

Wattage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5,550 watts

AC Load Current:

At 120 Volts . . . . . . . . . . . . . . . . . . . . . . . . .46.2 Amps

At 240 Volts . . . . . . . . . . . . . . . . . . . . . . . . .23.1 Amps

Phase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1–phase

Rated Frequency . . . . . . . . . . . . . . . . . . . . . . . . .60 Hertz

Fuel Tank Capacity . . . . . . . . . . . . . . . . . . . . 5 U.S. gallons

Shipping Weight . . . . . . . . . . . . . . . . . . . . . . . . . . 176 lbs.

GENERAL MAINTENANCE

RECOMMENDATIONS

The Owner/Operator is responsible for making sure that

all periodic maintenance tasks are completed on a timely

basis; that all discrepancies are corrected; and that the unit

is kept clean and properly stored. NEVER operate a

damaged or defective generator.

NOTE: Should you have questions about replacing

components on your Briggs & Stratton Power Products

generator, please call 1-800-743-4115 for assistance.

Engine Maintenance

See engine operator’s manual for instructions.

KEEP OUT OF REACH OF CHILDREN. DON'T

POLLUTE. CONSERVE RESOURCES. RETURN

USED OIL TO COLLECTION CENTERS.

Generator Maintenance

Generator maintenance consists of keeping the unit clean

and dry. Operate and store the unit in a clean dry

environment where it will not be exposed to excessive

dust, dirt, moisture or any corrosive vapors. Cooling air

slots in the generator must not become clogged with snow,

leaves or any other foreign material.

NOTE: DO NOT use a garden hose to clean generator.

Water can enter engine fuel system and cause problems. In

addition, if water enters generator through cooling air slots,

some of the water will be retained in voids and cracks of

the rotor and stator winding insulation.Water and dirt

buildup on the generator internal windings will eventually

decrease the insulation resistance of these windings.

Generator Cleaning

• Use a damp cloth to wipe exterior surfaces clean.

• Use a soft bristle brush to loosen caked on dirt or oil.

• Use a vacuum cleaner to pick up loose dirt and debris.

• Use low pressure air (not to exceed 25 psi) to blow

away dirt. Inspect cooling air slots and opening on

generator.These openings must be kept clean and

unobstructed.

• Used motor oil has been shown to cause skin cancer in

certain laboratory animals.

• Thoroughly wash exposed areas with soap and water.

Avoid prolonged or repeated skin contact with used

motor oil.

CAUTION

• DO NOT expose generator to excessive moisture, dust, dirt,

or corrosive vapors.

• DO NOT insert any objects through cooling slots.

Improper treatment of generator can damage it and

shorten its life.

CAUTION

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR

GENERATOR

• Disconnect the spark plug wire from the spark plug and place

the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

• Use approved spark plug tester.

• DO NOT check for spark with spark plug removed.

Unintentional sparking can result in fire or

electric shock.

WARNING

STORAGE

The generator should be started at least once every seven

days and allowed to run at least 30 minutes. If this cannot

be done and you must store the unit for more than

30 days, use the following guidelines to prepare it for

storage.

Generator Storage

• Clean the generator as outlined in “To Clean the

Generator.”

• Check that cooling air slots and openings on generator

are open and unobstructed.

Engine Storage

See engine operator’s manual for instructions.

Other Storage Tips

• Always store unit with fuel shut off valve in the “Off”

position (Figure 5, earlier).

• To prevent gum from forming in fuel system or on

essential carburetor parts, empty entire contents of both

supplied fuel stabilizer containers into fuel tank and fill

with fresh fuel. Run the unit for several minutes to

circulate the additive through the carburetor.The unit

and fuel can then be stored for up to 24 months.

Additional fuel stabilizer can be purchased locally.

• Fuel tank may swell in storage if vent is closed.When

storing generator with fuel in the tank, make sure the

vent knob is turned fully counter-clockwise.

• Store unit in clean and dry area.

• DO NOT place a storage cover over a hot generator.

• Let equipment cool for a sufficient time before placing the

cover on the equipment.

Storage covers can be flammable.

WARNING

TROUBLESHOOTING

Problem Cause Solution

Engine is running, but no AC

output is available.

1. Circuit breaker is open.

2. Poor connection or defective cord

set.

3. Connected device is bad.

4. Fault in generator.

1. Reset circuit breaker.

2. Check and repair.

3. Connect another device that is in

good condition.

4. Contact local service facility.

Engine runs good but bogs down

when loads are connected.

1. Short circuit in a connected load.

2. Generator is overloaded.

3. Shorted generator circuit.

1. Disconnect shorted electrical load.

2. See "Don't Overload Generator".

3. Contact local service facility.

Engine will not start; or starts and

runs rough.

1. Fuel valve is in the "Off" position.

2. Vent knob in fuel gauge is closed.

3. Quick connect in fuel line is

disconnected.

4. Out of gasoline.

1. Turn fuel valve to the "On"

position.

2. Open vent knob in fuel gauge.

3. Reconnect quick connect in fuel

line.

4. Fill fuel tank.

Engine shuts down during

operation.

Out of gasoline. Fill fuel tank.

Engine lacks power.

Load is too high. See "Don't Overload Generator".

NOTES

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC EQUIPMENT OWNER WARRANTY POLICY

LIMITED WARRANTY

Briggs & Stratton Power Products Group, LLC will repair or replace, free of charge, any part(s) of the equipment that is defective in material

or workmanship or both. Transportation charges on product submitted for repair or replacement under this warranty must be borne by

purchaser. This warranty is effective for the time periods and subject to the conditions stated below. For warranty service, find the nearest

Authorized Service Dealer in our dealer locator map at www.briggspowerproducts.com.

THERE IS NO OTHER EXPRESS WARRANTY. IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS

FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR FROM PURCHASE, OR TO THE EXTENT PERMITTED BY LAW ANY

AND ALL IMPLIED WARRANTIES ARE EXCLUDED. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES ARE EXCLUDED

TO THE EXTENT EXCLUSION IS PERMITTED BY LAW. Some states or countries do not allow limitations on how long an implied warranty

lasts, and some states or countries do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation

and exclusion may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state

to state or country to country.

OUR EQUIPMENT*

OUTBOARD

MOTOR

PRESSURE

WASHER

WATER PUMP

(Not available in the

USA)

PORTABLE

GENERATOR

WELDER

LLeessss tthhaann 1100 KKWW 1100 KKWW oorr ggrreeaatteerr

TTrraannssffeerr sswwiittcchh

2 years

none

1 year

90 days

1 year

90 days

2 years

1 year

2 years

none

3 years or

1500 hours

none

3 years

none

WARRANTY PERIOD**

HOME STANDBY GENERATOR SYSTEM

Consumer Use

Commercial Use

* The engine and starting batteries are warranted solely by the manufacturers of those products.

** 2 years for all consumer products in the European Union. Parts only on 2nd year for consumer use of Portable Generator and

Home Standby Generator System - Less than 10 KW, outside of European Union.

The warranty period begins on the date of purchase by the first retail consumer or commercial end user, and continues for the period of time

stated in the table above. “Consumer use" means personal residential household use by a retail consumer. “Commercial use" means all other

uses, including use for commercial, income producing or rental purposes. Once equipment has experienced commercial use, it shall thereafter

be considered as commercial use for purposes of this warranty. Equipment used for prime power in place of utility are not applicable to

this warranty. Electric powered pressure washers used for commercial purposes are not warranted.

NO WARRANTY REGISTRATION IS NECESSARY TO OBTAIN WARRANTY ON BRIGGS & STRATTON PRODUCTS. SAVE YOUR

PROOF OF PURCHASE RECEIPT. IF YOU DO NOT PROVIDE PROOF OF THE INITIAL PURCHASE DATE AT THE TIME WARRANTY

SERVICE IS REQUESTED, THE MANUFACTURING DATE OF THE PRODUCT WILL BE USED TO DETERMINE THE WARRANTY

PERIOD.

ABOUT YOUR WARRANTY

We welcome warranty repair and apologize to you for being inconvenienced. Any Authorized Service Dealer may perform warranty repairs. Most

warranty repairs are handled routinely, but sometimes requests for warranty service may not be appropriate. For example, warranty service would not

apply if equipment damage occurred because of misuse, lack of routine maintenance, shipping, handling, warehousing or improper installation.

Similarly, the warranty is void if the manufacturing date or the serial number on the equipment has been removed or the equipment has been altered

or modified. During the warranty period, the Authorized Service Dealer, at its option, will repair or replace any part that, upon examination, is found to

be defective under normal use and service. This warranty will not cover the following repairs and equipment:

• Normal Wear: Outdoor Power Equipment, like all mechanical devices, needs periodic parts and service to perform well. This warranty does not

cover repair when normal use has exhausted the life of a part or the equipment.

• Installation and Maintenance: This warranty does not apply to equipment or parts that have been subjected to improper or unauthorized

installation or alteration and modification, misuse, negligence, accident, overloading, overspeeding, improper maintenance, repair or storage so as,

in our judgment, to adversely affect its performance and reliability. This warranty also does not cover normal maintenance such as adjustments,

fuel system cleaning and obstruction (due to chemical, dirt, carbon, lime, etc.).

• Other Exclusions: This warranty excludes wear items such as quick couplers, oil gauges, belts, o-rings, filters, pump packing, etc., pumps that

have been run without water supplied or damage or malfunctions resulting from accidents, abuse, modifications, alterations, or improper servicing

or freezing or chemical deterioration. Accessory parts such as guns, hoses, wands and nozzles are excluded from the product warranty. This

warranty excludes failures due to acts of God and other force majeure events beyond the manufacturers control. Also excluded is used,

reconditioned, and demonstration equipment; equipment used for prime power in place of utility power and equipment used in life support

applications.

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC

JEFFERSON, WI, USA

Effective September 1, 2004 replaces all undated Warranties and all Warranties dated before September 1, 2004

RÈGLES DE SÉCURITÉ

TABLE DES MATIÈRES

Règles de Sécurité. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-18

Connaissez Votre Générateur . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Assemblage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-21

Opération . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-26

Entretien . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Rangement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Dépannage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Garantie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

DESCRIPTION DE L ÉQUIPEMENT

Lisez avec soin ce manuel et familiarisez-vous avec

votre générateur. Connaissez ses applications, ses

limitations et les dangers qu'il implique.

Ce générateur est un générateur entraîné par un moteur à champ

magnétique rotatif produisant du courant alternatif (c.a.). Il a été

conçu pour fournir du courant électrique pour faire marcher des

charges compatibles d'éclairage, d'appareils ménagers, d'outil et de

moteur. Le champ tournant du générateur est entraîné à

3,600 T/M par un moteur monocylindrique.

ATTENTION! NE PAS dépasser la capacité en watts ou en

Ampères du générateur.Voir "Ne Pas Surcharger le Générateur"

pour l'information spécifique.

Tout a été mis en oeuvre pour que les informations contenues

dans ce manuel soient exactes et à jour. Cependant, nous se

réserve le droit de changer, d'altérer ou d'améliorer le produit à

n'importe quel moment sans avis préalable.

Le Système de contrôle de l'émission du générateur est garanti pour

des normes établies par L'Agence de protection de l'environnement

et le California Air Resources Board. Pour des informations sur la

garantie, se reporter au manuel d'utilisation du moteur.

RÈGLES DE SÉCURITÉ

Ceci est la sûreté le symbole vif. Il est utilisé pour

vous alerter aux dangers de blessure personnels

potentiels. Obéir tous messages de sûreté qui suivent

ce symbole éviter la blessure ou la mort possibles.

Le symbole indiquant un message de sécurité est accompagné d'un

mot indicateur (DANGER,ATTENTION,AVERTISSEMENT), d'un

message illustré et/ou d'un message de sécurité visant à vous

avertir des dangers. DANGER indique un danger qui, s'il n'est pas

évité, provoquera des blessures graves, voire fatales.

AVERTISSEMENT indique un danger qui, s'il n'est pas évité, peut

provoquer des blessures graves, voire fatales. ATTENTION

indique un danger qui, s'il n'est pas évité, peut provoquer des

blessures mineures ou légères. Le mot ATTENTION, lorsqu'il est

utilisé sans le symbole d'alerte, indique une situation pouvant

endommager l'équipement. Suivez les messages de sécurité pour

éviter ou réduire les risques de blessures ou de mort.

Symboles de Danger et Moyens

L’échappement du moteur de ce produit contient des produits

chimiques que l’État de Californie considère comme causant le

cancer, des déformations à la naissance ou d’autres dangers

concernant la reproduction.

AVERTISSEMENT

Feu

Explosion

Emanations Toxiques

Surface Chaude

Choc Électrique

Recul

VEUILLEZ CONSERVER CES INSTRUCTIONS

RÈGLES DE SÉCURITÉ

• Faites fonctionner le générateur SEULEMENT à l'extérieur.

• Évitez que les gaz d'échappement entrent dans un espace restreint,

par une fenêtre, une porte, une prise d'aération ou toute autre

ouverture.

• NE FAITES PAS fonctionner le générateur à l'intérieur d'un bâtiment

ou d'un abri (même si les fenêtres et les portes sont ouvertes), y

compris à l'intérieur du compartiment d'un véhicule de plaisance.

Le générateur, lorsqu'il fonctionne, produit du monoxyde

de carbone, un gaz toxique inodore et incolore.

Le fait de respirer du monoxyde de carbone provoque

des nausées, des évanouissements ou peut être fatal.

AVERTISSEMENT

• Lorsque vous utilisez le générateur comme source d'énergie de

secours, il est nécessaire d'aviser les services publics d'électricité.

• Utilisez un disjoncteur différentiel lorsque vous utilisez l'appareil dans

des endroits humides ou extrêmement conductibles, comme les

terrasses en métal ou les ouvrages métalliques.

• NE touchez pas les fils dénudés ou les boîtiers.

• N'UTILISEZ pas le générateur avec des cordons électriques usés,

effilochés ou dénudés, ou abîmés de quelque sorte que ce soit.

• N'UTILISEZ pas le générateur sous la pluie.

• NE manipulez pas le générateur ou les cordons d'alimentation lorsque

vous êtes debout dans l'eau, pieds nus ou avec les mains ou les pieds

humides.

• NE laissez pas des personnes non qualifiées ou des enfants se servir

ou réparer le générateur.

Le générateur produit une tension élevée.

NE PAS isoler le générateur de l'installation électrique

risque de provoquer des blessures ou même d'être fatal

pour les ouvriers électriciens et de causer des dommages

au générateur dus à un "backfeed" d'énergie électrique.

AVERTISSEMENT

• Cette génératrice ne satisfait pas aux normes U. S. Coast Guard

Regulation 33CFR-183 et ne doit pas être utilisée pour des

applications marines.

• L'omission d'utiliser une génératrice appropriée et approuvée par U. S.

Coast Guard pourrait entraîner des blessures corporelles ou des

dommages matériels.

AVERTISSEMENT

LORS DE L'AJOUT OU DE LA VIDANGE DU

CARBURANT

• Éteignez le générateur et laissez-le refroidir au moins 2 minutes avant

de retirer le capuchon du réservoir de carburant. Desserrez lentement

le capuchon pour laisser la pression s'échapper du réservoir.

• Remplissez ou vidangez le réservoir d'essence à l'extérieur.

• NE REMPLISSEZ PAS trop le réservoir. Laissez l'expansion de

l'essence.

• Éloignez l'essence des étincelles, des flammes, des veilleuses, de la

chaleur et de toute autre source d'inflammation.

• N'ALLUMEZ PAS de cigarette ou ne fumez pas à proximité de l'appareil.

LORS DU DÉMARRAGE DE L'ÉQUIPEMENT

• Assurez-vous que la bougie d'allumage, le silencieux, le bouchon à

essence et le filtre à air sont en place.

• NE démarrez PAS le moteur lorsque la bougie d'allumage est enlevée.

• Si du carburant est renversé, attendez qu'il s'évapore avant de

démarrer le moteur.

LORSQUE L'ÉQUIPEMENT FONCTIONNE

• NE penchez PAS le moteur ou l'équipement, vous risqueriez de

renverser de l'essence.

• Cette génératrice n'est pas conçue pour être utilisée dans de

l'équipement mobile ou les applications marines.

LORSQUE VOUS TRANSPORTEZ OU RÉPAREZ

L'ÉQUIPEMENT

• Le réservoir d'essence doit être VIDE ou le robinet d'arrêt de

carburant doit être à la position fermée (OFF) pendant le transport

ou la réparation.

• Débranchez le câble de bougie.

LORSQUE VOUS ENTREPOSEZ L'ESSENCE OU UN

ÉQUIPEMENT AVEC UN RÉSERVOIR À ESSENCE

• Entreposez-le loin des appareils de chauffage, des fours, des chauffe-

eau, des sécheuses ou de tout autre appareil électroménager

disposant d'une veilleuse ou de toute autre source d'inflammation

risquant d'enflammer les vapeurs d'essence.

L'essence et ses vapeurs sont extrêmement

inflammables et explosives.

Le feu ou l'explosion risque de provoquer des

blessures graves, pouvant être fatales.

AVERTISSEMENT

• Lors du démarrage du moteur, tirez lentement sur la corde jusqu'à ce

que vous sentiez une résistance et tirez alors rapidement afin d'éviter

un effet de recul.

• NE démarrez JAMAIS ni n'arrêtez jamais le moteur alors que des

appareils électriques y sont branchés et en fonction.

Une rétroaction rapide de la corde du démarreur

(effet de recul) tirera votre main et votre bras vers le

moteur plus rapidement que vous ne pouvez relâcher

la corde.

Vous risquez ainsi de subir des fractures, des

ecchymoses ou des entorses.

AVERTISSEMENT

RÈGLES DE SÉCURITÉ

• NE TRAFIQUEZ PAS la vitesse régulée. Le générateur produit une

fréquence nominale et une tension correctes lorsqu'il fonctionne à

une vitesse régulée.

• NE modifiez le générateur d'aucune façon.

Les vitesses de fonctionnement excessivement élevées

augmentent les risques de blessure ou risquent d'endommager

le générateur.

Les vitesses extrêmement lentes entraînent une charge importante.

ATTENTION

• Voir la section " Ne Pas Surcharger Générateur ".

• Démarrez le générateur et laissez le moteur se stabiliser avant de

brancher les charges électriques.

• Branchez les charges électriques en position ARRÊT, puis, remettez en

position MARCHE.

• Éteignez les charges électriques et débranchez-les du générateur avant

de l'arrêter.

Dépasser la capacité de puissance ou d'ampérage du

générateur risque d'endommager ce dernier et/ou les autres

appareils électriques qui y sont branchés.

ATTENTION

• NE vous servez du générateur que pour les utilisations prévues.

• Si vous avez des questions concernant les utilisations prévues,

demandez à votre distributeur ou appelez 1-800-743-4115.

• Ne faites fonctionner le générateur que sur des surfaces horizontales.

• N'EXPOSEZ pas le générateur à une humidité excessive, à de la

poussière, à de la saleté ou à des vapeurs corrosives.

• N'INSÉREZ aucun objet dans les fentes de refroidissement.

• Si les appareils branchés sont en surchauffe, éteignez-les et

débranchez-les du générateur.

• Arrêtez le générateur si :

-la puissance électrique est inexistante;

-l'équipement produit des étincelles, de la fumée ou des flammes;

-l'unité vibre excessivement.

Un traitement inapproprié du générateur risque de

l'endommager et de raccourcir sa durée d'utilisation.

ATTENTION

LORSQUE VOUS RÉGLEZ OU RÉPAREZ VOTRE

GÉNÉRATEUR

• Débranchez toujours le câble de bougie et placez-le de façon à ce

qu'il ne soit pas en contact avec la bougie.

LORS DE TESTS D'ALLUMAGE DU MOTEUR

• Utilisez un vérificateur de bougies d'allumage approuvé.

• NE vérifiez PAS l'allumage lorsque la bougie d'allumage est enlevée.

Unintentional peut résulter dans feu ou électrique.

AVERTISSEMENT

• NE TOUCHEZ PAS aux pièces chaudes et évitez le contact avec les

gaz d’échappement.

• Laissez l'équipement refroidir avant de le toucher.

• Laissez un dégagement d’au moins 1,52 m (5 pi) tout autour de la

génératrice, y compris au-dessus.

• Le Code of Federal Regulation (CFR) Title 36 Parks, Forests, and Public

Property exige que de l’équipement alimenté par un moteur à

combustion interne soit doté d’un pare-étincelles et constamment

maintenu en bon état fonctionnement, conformément à la norme de

service 5100-1C de la USDA Forest ou à une révision de celle-ci. Dans

l’État de la Californie, un pare-étincelles est requis en vertu de la section

4442 du California Public Resources Code. Il se peut que d’autres États

aient des lois semblables.aux terres fédérales. Si vous équipez le silencieux

d'un pare-étincelles, il doit être en bon état de fonctionnement.

Les moteurs en fonctionnement produisent de la

chaleur. La température du silencieux et des endroits

à proximité peuvent atteindre, voire dépasser 150°F

(65°C).

Le contact de ces pièces risque de causer de graves

brûlures.

La chaleur et les gaz d’échappement peuvent

enflammer des matériaux combustibles et les

structures ainsi que causer des dommages au

réservoir d’essence et entraîner un incendie.

AVERTISSEMENT

La page est en cours de chargement...

Simplicity 030253-0 Manuel utilisateur

Marque: Simplicity

Modèle: 030253-0

Catégorie: Groupes électrogènes

Taper: Manuel utilisateur

Ce manuel convient également à

30253

Télécharger le PDF

rapport

dans d''autres langues

English: Simplicity 030253-0 User manual
español: Simplicity 030253-0 Manual de usuario

Simplicity 030253-0 Manuel utilisateur

Ce manuel convient également à

Simplicity 030253-0 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents