Wacker Neuson PSTF3750 Manuel utilisateur

0176744en 002 0510

0176744EN

Operator’s Manual

Pump

PST3 750

PSTF3 750

Copyright

notice

All rights, including copying and distribution rights, are reserved.

This publication may be photocopied by the original purchaser of the machine. Any

other type of reproduction is prohibited without express written permission from

Wacker Neuson Corporation.

Any type of reproduction or distribution not authorized by Wacker Neuson Corporation

represents an infringement of valid copyrights. Violators will be prosecuted.

Trademarks

All trademarks referenced in this manual are the property of their respective owners.

Manufacturer

Wacker Neuson Corporation

N92W15000 Anthony Avenue

Menomonee Falls, WI 53051 U.S.A.

Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957

www.wackerneuson.com

Original

instructions

This Operator’s Manual presents the original instructions. The original language of this

Operator’s Manual is American English.

PST3/PSTF3 750 Foreword

wc_tx001079gb.fm 3

Foreword

Machines

covered in

this manual

Machine

documentatio

n



Keep a copy of the Operator’s Manual with the machine at all times.



Use the separate Parts Book supplied with the machine to order replacement parts.



Refer to the separate Repair Manual for detailed instructions on servicing and

repairing the machine.



If you are missing any of these documents, please contact Wacker Neuson

Corporation to order a replacement or visit www.wackerneuson.com.



When ordering parts or requesting service information, be prepared to provide the

machine model number, item number, revision number, and serial number.

Expectations

for

information in

this manual



This manual provides information and procedures to safely operate and maintain

the above Wacker Neuson model(s). For your own safety and to reduce the risk of

injury, carefully read, understand, and observe all instructions described in this

manual.



Wacker Neuson Corporation expressly reserves the right to make technical

modifications, even without notice, which improve the performance or safety

standards of its machines.



The information contained in this manual is based on machines manufactured up

until the time of publication. Wacker Neuson Corporation reserves the right to

change any portion of this information without notice.

Manufacturer’

s approval

This manual contains references to approved parts, attachments, and modifications.

The following definitions apply:



Approved parts or attachments

are those either manufactured or provided by

Wacker Neuson.



Approved modifications

are those performed by an authorized Wacker Neuson

service center according to written instructions published by Wacker Neuson.



Unapproved parts, attachments, and modifications

are those that do not meet

the approved criteria.

Unapproved parts, attachments, or modifications may have the following

consequences:



Serious injury hazards to the operator and persons in the work area



Permanent damage to the machine which will not be covered under warranty

Contact your Wacker Neuson dealer immediately if you have questions about approved

or unapproved parts, attachments, or modifications.

Machine Item Number

PST3 750 0620337

0620440

PSTF3 750 0620338

0620441

Foreword PST3/PSTF3 750

4 wc_tx001079gb.fm

wc_bo0176744en_002TOC.fm 5

Table of ContentsPST3/PSTF3 750

Foreword 3

1 Safety Information 7

1.1 Signal Words Used in this Manual ....................................................... 7

1.2 Operating and Electrical Safety ............................................................ 8

1.3 Informational Labels ............................................................................. 8

2 Operation 9

2.1 Names of Parts ..................................................................................... 9

2.2 Prior to Operation ............................................................................... 10

2.3 Installation .......................................................................................... 10

2.4 Installing the Float (if equipped) ......................................................... 13

2.5 Electrical Wiring .................................................................................. 14

2.6 Electrical Circuit Diagrams ................................................................. 16

2.7 Operation ............................................................................................ 17

2.8 Automatic Operation (PSTF3 750 only) ............................................. 20

3 Maintenance 21

3.1 Periodic Maintenance Table ............................................................... 21

3.2 Maintenance and Inspection .............................................................. 22

3.3 Disassembly and Reassembly ........................................................... 24

3.4 Disassembly ....................................................................................... 24

3.5 Impeller Inspection ............................................................................. 25

3.6 Impeller Reassembly .......................................................................... 26

3.7 Troubleshooting .................................................................................. 27

4 Technical Data 29

4.1 Standard Specifications ...................................................................... 29

4.2 Operating Specifications .................................................................... 30

4.3 Dimensions ......................................................................................... 31

6 wc_bo0176744en_002TOC.fm

Table of Contents PST3/PSTF3 750

PST3/PSTF3 750 Safety Information

wc_si000288gb.fm 7

1 Safety Information

1.1 Signal Words Used in this Manual

This manual contains DANGER, WARNING, CAUTION, NOTICE, and

NOTE signal words which must be followed to reduce the possibility

of personal injury, damage to the equipment, or improper service.

NOTICE: Used without the safety alert symbol, NOTICE indicates a

situation which, if not avoided, could result in property damage.

Note: A Note contains additional information important to a procedure.

This is the safety alert symbol. It is used to alert you to potential personal hazards.

f Obey all safety messages that follow this symbol.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death

or serious injury.

f

To avoid death or serious injury from this type of hazard, obey all safety messages that

follow this signal word.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

f

To avoid possible death or serious injury from this type of hazard, obey all safety mes-

sages that follow this signal word.

CAUTION!

CAUTION indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

f

To avoid possible minor or moderate injury from this type of hazard, obey all safety mes-

sages that follow this signal word.

Safety Information PST3/PSTF3 750

8 wc_si000288gb.fm

1.2 Operating and Electrical Safety

To reduce risk of electric shock, connect only to a properly grounded,

grounding-type receptacle.

Risk of electric shock—this pump has not been investigated for use in

swimming pool areas.

An acceptable motor-control switch shall be provided at the time of

installation according to local codes and regulations.

To reduce risk of electric shock, follow instructions in this manual for

proper installation.

CAUTION: This pump may automatically restart. Prior to working on

the pump or control panel, all supply circuits must be disconnected.

CAUTION: Risk of shock—do not remove cord and strain relief.

1.3 Informational Labels

Label Meaning

A nameplate listing the model number, item num-

ber, revision number, and serial number is

attached to each unit. Please record the informa-

tion found on this plate so it will be available

should the nameplate become lost or damaged.

When ordering parts or requesting service infor-

mation, you will always be asked to specify the

model number, item number, revision number,

and serial number of the unit.

WARNING

Wacker Neuson Corporation

Menomonee Falls, WI 53051 USA

Model Item No. Rev.

Serial No.

VHz

kWkgMax. L/minMax. m

MADE IN

JAPAN

HPlbsMax. GPMMax. ft

CUS

L

I

S

T

E

D

R

Phase

C22.2 No. 108-M89

2001993

Conforms to UL Std. 778

Cert. to CAN/CSA St d.

Amp.

Man. Y/M

THERMALLY PROTECTED

INDOORS OR OUTDOORS

CSA ENCLOSURE 3

PST3/PSTF3 750 Operation

wc_tx000987gb.fm 9

2 Operation

2.1 Names of Parts

See Graphic: wc_gr005663

Ref. Description Ref. Description

1 Lifting handle 8 Cable assembly

2 Mechanical seal 9 Oil plug

3 Lubricant 10 Oil lifter

4 Oil casing 11 Shaft sleeve

5 Hose coupling 12 Impeller

6 Pump casing 13 Stirrer

7 Casing packing 14 Strainer stand

wc_gr00566

3

1

8

10

9

11

12

13

14

2

3

4

5

6

7

Operation PST3/PSTF3 750

10 wc_tx000987gb.fm

2.2 Prior to Operation

When the pump is delivered, first perform the following checks:

• Inspection

While unpacking, inspect the product for damage during shipment, and

make sure all bolts and nuts are tightened properly.

• Specification check

Check the model number to make sure it is the product that was

ordered. Be certain it is the correct voltage and frequency.

Note: If there is any problem with the product as shipped, contact your

nearest dealer or Wacker Neuson representative at once.

• Product specifications

Do not operate this product under any conditions other than those for

which it is specified. Failure to observe this precaution can lead to

electrical shock, current leakage, fire, water leakage or other

problems.

2.3 Installation

If the pump is used to drain a swimming pool, the pump must be

connected to a Ground Fault Interrupter (GFI).

If the pump is used in fountains, the pump must be connected to a

Ground Fault Interrupter (GFI).

The pump must not be used when people are in the water.

Leakage of pump lubricants may cause pollution of water.

Proper plug must be provided according to local codes and standards.

Refer to wiring diagram.

Do not use this pump in liquids other than water, such as oil, salt water,

or organic solvents.

Use with a power supply voltage within ±5% of the rated voltage.

Do not use in water temperatures outside the range of 0–40°C

(32–104°F) which can lead to failure, current leakage or shock.

Do not use in the vicinity of explosive or flammable materials.

Use only in fully assembled state.

Note: Consult your local dealer or Wacker Neuson representative

before using with any liquids other than those indicated in this

document.

CAUTION

WARNING

PST3/PSTF3 750 Operation

wc_tx000987gb.fm 11

Preparing for installation

Before installing the pump at a work site, you will need to have the

following tools and instruments ready:

• Insulation resistance tester (megohmmeter)

• AC voltmeter

• AC ammeter (clamp-on type)

• Bolt and nut tighteners

• Power supply connection tools (screwdriver or box wrench)

Note: Please also read the instructions that come with each of the test

instruments.

Checks to Make Before Installation

When a three-prong grounded plug is used:

Use the megohmmeter to measure the motor insulation resistance

between the grounding prong and each one of the two power prongs.

When connection wires are used:

With the megohmmeter, measure the insulation resistance between

the ground wire (Green) and each one of the two power wires.

Reference insulation resistance: 20MΩ or greater.

Note: The reference insulation resistance (20MΩ or greater) is the

value when the pump is new or has been repaired. For the reference

value after installation, see the Periodic Maintenance table.

Precautions in Installation

When installing the pump, pay close attention to its center of gravity

and weight. If it is not lowered into place correctly, it may fall and be

damaged or cause injury.

When transporting the machine by hand, be sure to employ manpower

commensurate with the weight of the machine. To avoid back injury

when lifting the machine, bend the knees to pick it up rather than

bending your back only.

Do not under any circumstances install or move the pump by

suspending it from the cable assembly. The cable may be damaged,

causing current leakage, shock, or fire.

2.3.1 Avoid dropping the pump or other strong impact. Lift the pump by

holding it firmly with the hands or by attaching a rope or chain to the

lifting handle.

Note: On cable assembly handling, see Electrical Wiring.

Avoid dry operation, which will not only lower performance but can

cause the pump to malfunction, leading to electrical leakage and

shock.

WARNING

CAUTION

Operation PST3/PSTF3 750

12 wc_tx000987gb.fm

2.3.2 Install the pump in a location with sufficient water level, where water

collects readily.

Note: See Operation (“Operating Water Level”) for the water level

necessary for operation.

Note: The discharge end of the hose should be located higher than the

water surface. If the end of the hose is submerged, water may flow

back to the pump when the pump is stopped; and if the hose end is

lower than the water surface, water may overflow when the pump is

turned off.

If large quantities of earth are sucked up, damage resulting from

friction in the pump can lead to current leakage and shock.

2.3.3 Use the pump in the upright position. To prevent the strainer from

becoming submerged in mud, causing it to suck in sand or debris,

mount it on a block or other firm base.

2.3.4 If used in a permanent installation where the pump is not readily

accessible after installation, please contact Wacker Neuson for a

duplicate nameplate to be installed at the wellhead or on the control

box so that it will be readily visible.

CAUTION

PST3/PSTF3 750 Operation

wc_tx000987gb.fm 13

2.4 Installing the Float (if equipped)

See graphic: wc_gr005664

2.4.1 Set the length of the float lead wire to the dimension indicated below.

Failure to set the correct lead wire length will lead to improper

operation of the pump.

NOTICE: Install the float so that it moves freely up and down. If the

float binds or catches, it will cause the pump to operate improperly.

Pump model Length “L”

PSTF3 750 150 mm (5.9 in.)

wc_gr005664

Operation PST3/PSTF3 750

14 wc_tx000987gb.fm

2.5 Electrical Wiring

Performing electrical wiring

Electrical wiring should be performed by a qualified person in accord

with all applicable regulations. Failure to observe this precaution not

only risks breaking the law but is extremely dangerous.

Incorrect wiring can lead to current leakage, electrical shock or fire.

Always make sure the pump is equipped with the specified overload

protectors and fuses or breakers, so as to prevent electrical shock from

a current leak or pump malfunction.

Operate within the capacity of the power supply and wiring.

Grounding

Do not use the pump without first grounding it properly. Failure to

ground it can lead to electrical shock from a current leak or pump

malfunction.

Do not attach the grounding wire to a gas pipe, water pipe, lightning

arrester or telephone grounding wire. Improper grounding can result in

electrical shock.

Connecting the power supply

Before connecting wires to the terminal, make certain the power supply

is turned off (circuit breaker, etc.), to avoid electrical shock, shorting,

or unexpected starting of the pump, leading to injury.

Before inserting the power supply plug, make certain the power supply

is turned off (circuit breaker, etc.), to avoid electrical shock, shorting,

or unexpected starting of the pump, leading to injury.

Do not use the pump with the cable assembly or plug connected

loosely, which can result in electric shock, shorting, or fire.

Draw power from a dedicated power outlet rated at 15 A or above.

Sharing the outlet with other equipment may cause overheating at the

branch outlet and could result in fire.

• The grounded plug shall be connected as shown in the drawing.

NOTICE: Be sure to use a dedicated power supply with a ground

leakage circuit breaker.

Note: The shape of the plug may differ from that shown in the

illustration.

See Graphic: wc_gr000242

WARNING

CAUTION

WARNING

CAUTION

PST3/PSTF3 750 Operation

wc_tx000987gb.fm 15

Cable Assembly

If it is necessary to extend the cable assembly, use a core size equal

to or larger than the original. This is necessary not only to avoid a

performance drop, but to prevent cable overheating which can result in

fire, electrical leakage or electrical shock.

If a cable with cut insulation or other damage is submerged in the

water, there is a danger of damage to the pump, electrical leakage,

electrical shock, or fire.

Be careful not to let the cable assembly be cut or become twisted. This

may result in damage to the pump, electrical leakage, electrical shock,

or fire.

If it is necessary to submerge the connection wires of the cable

assembly in water, first seal the wires completely in a molded

protective sleeve, to prevent electrical leakage, electrical shock, or fire.

Do not allow the cable assembly wires or power supply plug to become

wet.

Make sure the cable does not become excessively bent or twisted, and

does not rub against a structure in a way that might damage it.

If used in a deep-well installation, the cable assembly should be

secured every 6 m (20 ft.).

CAUTION

Operation PST3/PSTF3 750

16 wc_tx000987gb.fm

2.6 Electrical Circuit Diagrams

See Graphic: wc_gr005665

If connected to a circuit protected by a fuse, use a time-delay fuse with

this pump.

Ref. Description Ref. Description

1 Capacitor 6 Ground

2 Main coil 7 Circle thermal protector

3 Auxiliary coil 8 Float switch

(normally open contact)

4 Miniature protector 9 Heater

5 Frame grounding

Wire Colors

B Black V Violet Or Orange

G Green W White Pr Purple

L Blue Y Yellow Sh Shield

P Pink Br Brown LL Light Blue

R Red Cl Clear G/Y Green/Yellow

T Tan Gr Gray

wc_gr005665

PST3 750

PSTF3 750

W (L)

W

9

G (G/Y)

6

5

7

1

3

2

9

R(Br) R

Y/G

B

LL

W (L)

6

5

8

1

3

2

R(Br)

R

Y/G

B

LL

CAUTION

PST3/PSTF3 750 Operation

wc_tx000987gb.fm 17

2.7 Operation

Before starting

2.7.1 Make sure once again that the product is of the correct voltage and

frequency rating.

NOTICE: Using the product at other than rated voltage and frequency

will not only lower its performance but may damage the product.

Note: Confirm the rated voltage and frequency on the model

nameplate.

2.7.2 Confirm the wiring, supply voltage, circuit breaker capacity, and motor

insulation resistance.

Reference insulation resistance = 20 MΩ or greater.

Note: The reference insulation resistance (20 MΩ or greater) is the

value when the pump is new or has been repaired. For the reference

value after installation see “Periodic Maintenance Table.”

2.7.3 The setting on the circuit breaker or other overload protector should be

made in accord with the rated current of the pump.

Note: See “Operating Specifications” for the rated current of the pump.

2.7.4 When powering the pump with a generator, be certain the generator is

sized to supply the required power for the pump and any other

equipment powered by the generator.

Test Operation

Do not operate the pump while it is suspended in the air. The recoil

may result in injury or other major accident.

Do not start the pump when people are standing next to it. A current

leak can result in electrical shock.

Run the pump for a short time (3–10 minutes) and confirm the

following:

• Using an ammeter (clamp-on type), measure the operating cur-

rent at the L1 and L2 phase wires on the terminal.

COUNTERMEASURE: If the operating current exceeds the rated

value, pump motor overload may be a cause. Make sure the pump has

been installed under proper conditions as described in Installation.

• Using an AC voltmeter (tester), measure voltage at the terminals.

Supply voltage tolerance: within ±5% of rated voltage.

WARNING

Operation PST3/PSTF3 750

18 wc_tx000987gb.fm

COUNTERMEASURE: If the supply voltage is outside the tolerance,

possible causes are the power supply capacity or an inadequate

extension cable. Look again at the wiring diagram and make sure the

conditions are proper.

In case of very excessive vibration, unusual noise or odor, turn off the

power immediately and consult your nearest dealer or Wacker Neuson

representative. Continuing to operate the pump under abnormal

conditions may result in electrical shock, fire, or current leakage.

Operation

The pump may become very hot during operation. Be careful not to

contact the pump accidentally to avoid being burned.

Make sure no extraneous objects such as pins, nails or other metal

objects are sucked into the pump. These can damage the pump or

cause it to malfunction, and can result in electrical shock or electrical

leakage.

When the pump is not used for an extended period, be sure to turn off

the power (circuit breaker, etc.). Deterioration of the insulation may

lead to electrical leakage, electrical shock, or fire.

In case of a power outage, turn off the power to the pump to avoid

having it start unexpectedly when the power is restored, presenting

serious danger to people in the vicinity.

Pay careful attention to the water level while the pump is operating. Dry

operation may cause the pump to malfunction.

Note: See section “Operating water level” for the water level

necessary for operation.

If the protection system operates due to an overload or malfunction,

causing the pump to stop, first investigate and remove the cause

before restarting.

Sharp bends in the hose, especially near its base, may cause air

pockets to form resulting in idle operation. Lessen the degree of

bending while continuing to operate the pump.

CAUTION

WARNING

PST3/PSTF3 750 Operation

wc_tx000987gb.fm 19

Operating water level

Do not operate the pump below the C.W.L. (Continuous running Water

Level) indicated below. Failure to observe this condition may result in

damage to the pump, current leakage or electrical shock.

See Graphic: wc_gr005667

.

Motor Protection System (Motor Protector)

The pump has a built-in motor protection system (Miniature Protector).

If the motor overheats, for reasons such as the following, the pump will

automatically stop operating regardless of the water level, to protect

the motor:

• Change in supply voltage polarity

• Overload

• Open-phase operation or operation under constraint

Note: Always determine the cause of the problem and resolve it before

resuming operation. Simply repeating cycles of stopping and restarting

will result in damage to the pump. Do not continue operation at very

low lift, low water level, or while the strainer is clogged with debris. Not

only will performance suffer, but also such conditions may cause

noise, heavy vibration, and malfunctioning.

Pump Model

Continuous running Water Level

(C.W.L.)

PST3 750

PSTF3 750

90 mm (3.5 in)

180 mm (7.1 in.)

CAUTION

wc

_g

r005667

Operation PST3/PSTF3 750

20 wc_tx000987gb.fm

2.8 Automatic Operation (PSTF3 750 only)

See Graphic: wc_gr005666

The PSTF3 750 pump is equipped with a float switch to detect the

water level. The float switch (a) enables the pump to perform an

automatic drainage operation when connected to a continuous power

supply.

Connect the power and perform a trial operation as follows:

2.8.1 Move the float switch down to its lowest position.

2.8.2 Raise the float switch. This will start the pump.

2.8.3 Lower the float switch to its original position. This will stop the pump.

2.8.4 Repeat this cycle two or three more times to verify the operation. Note:

The trial operation must be completed within one minute.

If the pump operates abnormally (i.e. exhibits an unusually large

amount of vibration, noise, or odor), disconnect the power supply

immediately and contact your Wacker Neuson dealer. Do not operate

the pump in this condition, otherwise there is a risk of current leakage,

electrical shock, or fire.

wc_gr005666

a

CAUTION

La page charge ...

Wacker Neuson PSTF3750 Manuel utilisateur

Ce manuel convient également à

Wacker Neuson PSTF3750 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents