Wacker Neuson PS32200 Manuel utilisateur

www.wackergroup.com

Pump

PS 3 1500

PS 3 2200

OPERATOR’S MANUAL

0154622en 002

0603

0154622EN

PS 3 1500/ PS 3 2200 Table of Contents

wc_bo0154622002enTOC.fm 1

1. Foreword 3

2. Safety Information 4

2.1 Operating and Electrical Safety ............................................................ 5

2.2 Information Labels ................................................................................ 5

3. Technical Data 6

3.1 Standard Specifications ........................................................................ 6

3.2 Operating Specifications (60 Hz) .......................................................... 7

4. Operation 8

4.1 Names of Parts ..................................................................................... 8

4.2 Prior to Operation ................................................................................. 9

4.3 Installation ............................................................................................ 9

4.4 Electrical Wiring .................................................................................. 12

4.5 Electrical Circuit Diagrams ................................................................. 14

4.6 Operation ............................................................................................ 16

5. Maintenance 19

5.1 Periodic Maintenance Schedule ......................................................... 19

5.2 Maintenance and Inspection .............................................................. 20

5.3 Disassembly and Reassembly ........................................................... 22

5.4 Disassembly ....................................................................................... 23

5.5 Reassembly Procedure ...................................................................... 23

5.6 Troubleshooting .................................................................................. 25

Table of Contents PS 3 1500/ PS 3 2200

wc_bo0154622002enTOC.fm 2

Foreword

wc_tx000001gb electric.fm 3

1. Foreword

This manual provides information and procedures to safely operate

and maintain this Wacker model. For your own safety and protection

from injury, carefully read, understand and observe the safety

instructions described in this manual.

Keep this manual or a copy of it with the machine. If you lose this

manual or need an additional copy, please contact Wacker

Corporation. This machine is built with user safety in mind; however,

it can present hazards if improperly operated and serviced. Follow

operating instructions carefully! If you have questions about operating

or servicing this equipment, please contact Wacker Corporation.

The information contained in this manual was based on machines in

production at the time of publication. Wacker Corporation reserves the

right to change any portion of this information without notice.

All rights, especially copying and distribution rights, are reserved.

No part of this publication may be reproduced in any form or by any

means, electronic or mechanical, including photocopying, without

express written permission from Wacker Corporation.

Any type of reproduction or distribution not authorized by Wacker

Corporation represents an infringement of valid copyrights and will be

prosecuted. We expressly reserve the right to make technical

modifications, even without due notice, which aim at improving our

machines or their safety standards.

Safety Information PS 3 1500 / PS 3 2200

wc_si000036gb.fm 4

2. Safety Information

This manual contains DANGER, WARNING, CAUTION, and NOTE

callouts which must be followed to reduce the possibility of personal

injury, damage to the equipment, or improper service.

This is the safety alert symbol. It is used to alert you to potential

personal injury hazards. Obey all safety messages that follow this

symbol to avoid possible injury or death.

DANGER indicates an imminently hazardous situation which, if not

avoided, will result in death or serious injury.

WARNING indicates a potentially hazardous situation which, if not

avoided, could result in death or serious injury.

CAUTION indicates a potentially hazardous situation which, if not

avoided, may result in minor or moderate injury.

CAUTION: Used without the safety alert symbol, CAUTION indicates

a potentially hazardous situation which, if not avoided, may result in

property damage.

Note:

Contains additional information important to a procedure.

DANGER

WARNING

CAUTION

PS 3 1500 / PS 3 2200 Safety Information

wc_si000036gb.fm 5

2.1 Operating and Electrical Safety

To reduce risk of electric shock, connect only to a properly grounded,

grounding-type receptacle.

Risk of electric shock - This pump has not been investigated for use in

swimming pool areas.

An acceptable motor-control switch shall be provided at the time of

installation according to local codes and regulations.

To reduce risk of electric shock, see instruction manual for proper

installation.

CAUTION: This pump may automatically restart. Prior to working on

the pump or control panel all supply circuits must be disconnected.

CAUTION: Risk of shock - Do not remove cord and strain relief.

2.2 Information Labels

Label Meaning

A nameplate listing the Model Number, Item

Number, Revision, and Serial Number is

attached to each unit. Please record the informa-

tion found on this plate so it will be available

should the nameplate become lost or damaged.

When ordering parts or requesting service infor-

mation, you will always be asked to specify the

model, item number, revision number, and serial

number of the unit.

WARNING

Technical Data PS 3 1500 / PS 3 2200

wc_td000036gb.fm 6

3. Technical Data

3.1 Standard Specifications

Applicable Liquids,

Consistency and

Temperature

Rain Water, Fountain Water, Ground Water,

Sand-Carrying Water

0–40°C (32–104°F)

Pump Impeller Semi-Vortex Type

Shaft Seal Double Mechanical Seal

Bearing Shielded Ball Bearing

Motor Specification Dry Submersible Induction Motor (2-Pole)

Insulation Class B

Protection System Circle Thermal Protector

Lubricant SAE 10W/20W

Such as:

–Turbine Oil ISO VG #32

–Shell Victrolia Oil #27

–British Pet Energol THB #32

–Gulf Paramount #32

–Tellus #T22 Shell Oil

–Shell Turbo T32

Connection Coupling (NPT 3”)

PS 3 1500 / PS 3 2200 Technical Data

wc_td000036gb.fm 7

3.2 Operating Specifications (60 Hz)

*The weight (mass) given above is the operating weight of the pump itself, not including the cable

assembly.

Part No.

PS 3 1500 PS 3 2200

0009119

0009117 0009118

Pump

Bore

mm (in.)

80 (3)

Phase 1

Starting Method Capacitor-Run Capacitor-Start

Capacitor-Run

Output

kW (Hp)

1.5 (2) 2.2 (2)

Rated Current

A

(V)

23.0

110

11.5

220

13.0

220

Maximum Head

m (ft.)

21 (69) 26 (85)

Maximum Capacity

L/min

(GPM)

420

(111)

493

(130)

Maximum Pressure

kg/cm

2

(psi)

2.1

(30)

2.6

(37)

Solid Size Capacity

mm (in.)

8.5 (0.3)

Weight*

Kg (lbs.)

28.8 (63.5) 29.0 (64)

Operation PS 3 1500 / PS 2 2200

wc_tx000115gb.fm 8

4. Operation

4.1 Names of Parts

See Graphic: wc_gr000321

Ref. Description Ref. Description

1. Coupling 9. Dust Seal

2. Mechanical Seal 10. Wear Ring

3. Gasket 11. Oil Housing

4. Sleeve 12. Impeller

5. Cable Assembly 13. Volute

6. Lifting Handle 14. Strainer

7. Lubricant 15. Retainer Plate

8. Oil Plug

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

wc_gr000321

PS 3 1500 / PS 2 2200 Operation

wc_tx000115gb.fm 9

4.2 Prior to Operation

When the pump is delivered, first perform the following checks:

• Inspection

While unpacking, inspect the product for damage during shipment, and

make sure all bolts and nuts are tightened properly.

• Specification check

Check the model number to make sure it is the product that was

ordered. Be certain it is the correct voltage and frequency.

Note:

If there is any problem with the product as shipped, contact your

nearest dealer or Wacker representative at once.

• Product specifications

Do not operate this product under any conditions other than those for

which it is specified. Failure to observe this precaution can lead to

electrical shock, current leakage, fire, water leakage or other

problems.

4.3 Installation

If the pump is used to drain a swimming pool, the pump must be

connected to a Ground Fault Interrupter (GFI).

If the pump is used in fountains, the pump must be connected to a

Ground Fault Interrupter (GFI).

The pump must not be used when people are in the water.

Leakage of pump lubricants may cause pollution of water.

Proper plug must be provided according to local codes and standards.

Refer to wiring diagram.

DO NOT use this pump in liquids other than water, such as oil, salt

water, or organic solvents.

Use with a power supply voltage within ±5% of the rated voltage.

DO NOT use in water temperatures outside the range of 32–104°F (0–

40°C) which can lead to failure, current leakage or shock.

DO NOT use in the vicinity of explosive or flammable materials.

Use only in fully assembled state.

Note:

Consult your local dealer or Wacker representative before using

with any liquids other than those indicated in this document.

Maximum Allowable Water Pressure

CAUTION

WARNING

Operation PS 3 1500 / PS 2 2200

wc_tx000115gb.fm 10

CAUTION: Do not use at greater than the water pressure shown,

which can damage the pump resulting in electrical leakage and

electrical shock.

Preparing for Installation

Before installing the pump at a work site, you will need to have the

following tools and instruments ready:

• Insulation resistance tester (megohmmeter)

• AC voltmeter

• AC ammeter (clamp-on type)

• Bolt and nut tighteners

• Power supply connection tools (screwdriver or box wrench)

Note:

Please also read the instructions that come with each of the test

instruments.

Checks to Make Before Installation

With the megohmmeter, measure the insulation resistance between

each of the power wires and grounding wire to verify the insulation

resistance of the motor.

Reference insulation resistance: 20MW or greater

Note:

The reference insulation resistance (20M

W

or greater) is the

value when the pump is new or has been repaired. For the reference

value after installation, see Maintenance and Inspection.

Precautions in Installation

When installing the pump, pay close attention to its center of gravity

and weight. If it is not lowered into place correctly, it may fall and be

damaged or cause injury.

When transporting the pump by hand, be sure to employ manpower

commensurate with the weight of the pump. To avoid back injury when

lifting the pump, bend the knees to pick it up rather than bending your

back only.

Do not under any circumstances install or move the pump by

suspending it from the cable assembly. The cable may be damaged,

causing electrical leakage, shock, or fire.

Model Maximum Allowable Water Pressure

PS 3 1500/2200 0.3 MPa (43 PSI)

WARNING

CAUTION

PS 3 1500 / PS 2 2200 Operation

wc_tx000115gb.fm 11

4.3.1 The pump is supplied with a threaded discharge fitting. Tighten hose

coupling or discharge pipe securely and with proper gaskets.

4.3.2 Avoid dropping the pump or other strong impact. Lift the pump by

holding it firmly with the hands or by attaching a rope or chain to the

lifting handle.

Note:

On cable assembly handling, see Electrical Wiring.

4.3.3 Install the pump in a location with sufficient water level, where water

collects readily.

Note:

See Operation (“Operating Water Level”) for the water level

necessary for operation. The discharge end of the hose should be

located higher than the water surface. If the end of the hose is

submerged, water may flow back to the pump when the pump is

stopped; and if the hose end is lower than the water surface, water may

overflow when the pump is turned off.

4.3.4 The hose should be run as straight as possible, since excessive

bending will hinder the water flow, preventing sufficient lift, and can

even cause the hose to become clogged with earth. If the hose is

crimped near the pump, air can become trapped in the pump and

cause idle running.

If large quantities of earth are sucked up, damage resulting from

friction in the pump can lead to electrical leakage and shock.

CAUTION: When the pump is installed at a work site, make sure the

hose is connected in such a way as to ensure proper drainage.

Otherwise water may leak out and cause damage to surrounding walls

or flooring, or to equipment.

4.3.5 Use the pump in the upright position. To prevent the strainer from

becoming submerged in mud, causing it to suck in sand or debris,

mount it on a block or other firm base.

4.3.6 If used in a permanent installation, where the pump is not readily

accessible after installation, please contact Wacker for a duplicate

nameplate to be installed at the wellhead or on the control box so that

it will be readily visible.

4.3.7 Do not operate the pump dry. Doing so will prevent the pump from

attaining its full potential and may also damage the pump and lead to

a short and electrical shock.

CAUTION

Operation PS 3 1500 / PS 2 2200

wc_tx000115gb.fm 12

4.4 Electrical Wiring

Performing electrical wiring

Electrical wiring should be performed by a qualified person in accord

with all applicable regulations. Failure to observe this precaution not

only risks breaking the law but is extremely dangerous.

Incorrect wiring can lead to current leakage, electrical shock or fire.

ALWAYS make sure the pump is equipped with the specified overload

protectors and fuses or breakers, so as to prevent electrical shock from

a current leak or pump malfunction.

Operate within the capacity of the power supply and wiring.

Grounding

DO NOT use the pump without first grounding it properly. Failure to

ground it can lead to electrical shock from a current leak or pump

malfunction.

DO NOT attach the grounding wire to a gas pipe, water pipe, lightning

arrestor or telephone grounding wire. Improper grounding can result in

electrical shock.

Connecting the power supply

Before connecting leads to the terminal strip, make certain the power

supply is turned off (circuit breaker, etc.), to avoid electrical shock,

shorting, or unexpected starting of the pump, leading to injury.

Do not use the pump if the cable assembly is worn or damaged, which

can result in electric shock, shorting, or fire.

Connect the leads to the control panel terminals as shown in the

diagram, making sure they do not become twisted together.

See Graphic: wc_gr000260

WARNING

CAUTION

WARNING

CAUTION

R

W

G

wc_gr000260

PS 3 1500 / PS 2 2200 Operation

wc_tx000115gb.fm 13

Cable Assembly

If it is necessary to extend the cable assembly, use a core size equal

to or larger than the original. This is necessary not only for avoiding a

performance drop, but to prevent cable overheating which can result in

fire, electrical leakage or electrical shock.

If a cable with cut insulation or other damage is submerged in the

water, there is a danger of damage to the pump, electrical leakage,

electrical shock, or fire.

Be careful not to let the cable assembly be cut or become twisted. This

may result in damage to the pump, electrical leakage, electrical shock,

or fire.

If it is necessary to submerge the connection wires of the cable

assembly in water, first seal the wires completely in a molded

protective sleeve, to prevent electrical leakage, electrical shock, or fire.

DO NOT allow the cable assembly wires or power supply plug to

become wet.

Make sure the cable does not become excessively bent or twisted, and

does not rub against a structure in a way that might damage it.

If used in a deep-well installation, the cable assembly should be

secured every twenty feet.

CAUTION

Operation PS 3 1500 / PS 2 2200

wc_tx000115gb.fm 14

4.5 Electrical Circuit Diagrams

See Graphic: wc_gr000322 and wc_gr000323

PS 3 1500 CAPACITOR-START MODELS, SINGLE PHASE MOTOR

Ref. Description Ref. Description

A Protector E Main Coil

B Heater F Aux. Coil

C Bi-metal G Centrifugal Switch

D To Power Supply H Capacitor

Wire Colors

B Black R Red Y Yellow Or Orange

G Green T Tan Br Brown Pr Purple

L Blue V Violet Cl Clear Sh Shield

P Pink W White Gr Gray LL Light Blue

A

B

E

H

C

2

3

1

F

G

D

wc_gr000322

PS 3 1500 / PS 2 2200 Operation

wc_tx000115gb.fm 15

PS 3 2200 CAPACITOR-START AND -RUN MODELS, SINGLE PHASE MOTOR

If connected to a circuit protected by a fuse, use a time-delay fuse with

this pump.

Ref. Description Ref. Description

A Protector E Main Coil

B Heater F Aux. Coil

C Bi-metal G Centrifugal Switch

D To Power Supply H Starting Capacitor

J Running Capactor

Wire Colors

B Black R Red Y Yellow Or Orange

G Green T Tan Br Brown Pr Purple

L Blue V Violet Cl Clear Sh Shield

P Pink W White Gr Gray LL Light Blue

A

B

E

H

C

2

3

1

F

G

D

wc_gr000323

J

CAUTION

Operation PS 3 1500 / PS 2 2200

wc_tx000115gb.fm 16

4.6 Operation

Before starting

4.6.1 Make sure once again that the product is of the correct voltage and

frequency rating.

CAUTION: Using the product at other than rated voltage and

frequency will not only lower its performance but may damage the

product.

Note:

Confirm the rated voltage and frequency on the model

nameplate.

4.6.2 Confirm the wiring, supply voltage, circuit breaker capacity, and motor

insulation resistance.

Reference insulation resistance = 20 MΩ or greater.

Note:

The reference insulation resistance (20 M

Ω

or greater) is the

value when the pump is new or has been repaired. For the reference

value after installation see Maintenance and Inspection.

4.6.3 The setting on the circuit breaker or other overload protector should be

made in accord with the rated current of the pump.

Note:

See Standard Specifications for the rated current of the pump.

4.6.4 When powering the pump with a generator, be certain the generator is

sized to supply the required power for the pump and any other

equipment powered by the generator.

Test Operation

NEVER operate the pump while it is suspended in the air. The recoil

may result in injury or other major accident.

NEVER start the pump when people are standing next to it. A current

leak can result in electrical shock.

Run the pump for a short time (3–10 minutes) and confirm the

following:

• Using an ammeter (clamp-on type), measure the operating cur-

rent at the L1 and L2 phase wires on the terminal.

COUNTERMEASURE: If the operating current exceeds the rated

value, pump motor overload may be a cause. Make sure the pump has

been installed under proper conditions as described in

Installation

.

• Using an AC voltmeter (tester), measure voltage at the terminals.

Supply voltage tolerance: within ±5% of rated voltage.

WARNING

PS 3 1500 / PS 2 2200 Operation

wc_tx000115gb.fm 17

COUNTERMEASURE: If the supply voltage is outside the tolerance,

possible causes are the power supply capacity or an inadequate

extension cable. Look again at

Electrical Wiring

and make sure the

conditions are proper.

In case of very excessive vibration, unusual noise or odor, turn off the

power immediately and consult with your nearest dealer or Wacker

representative. Continuing to operate the pump under abnormal

conditions may result in electrical shock, fire, or current leakage.

Operation

Make sure no extraneous objects such as pins, nails or other metal

objects are sucked into the pump. These can damage the pump or

cause it to malfunction, and can result in electrical shock or electrical

leakage.

When the pump is not used for an extended period, be sure to turn off

the power (circuit breaker, etc.). Deterioration of the insulation may

lead to electrical leakage, electrical shock, or fire.

In case of a power outage, turn off the power to the pump to avoid

having it start unexpectedly when the power is restored, presenting

serious danger to people in the vicinity.

The pump may become hot during operation. Do not touch an

operating pump. Allow the pump to cool before handling.

Pay careful attention to the water level while the pump is operating. Dry

operation may cause the pump to malfunction.

Note:

See section Operating water level, for the water level necessary

for operation.

If the protection system operates due to an overload or malfunction,

causing the pump to stop, first investigate and remove the cause

before restarting.

CAUTION

WARNING

CAUTION

Operation PS 3 1500 / PS 2 2200

wc_tx000115gb.fm 18

Operating water level

Do not operate the pump below the C.W.L. (Continuous running Water

Level) indicated below. Failure to observe this condition may result in

damage to the pump, current leakage or electrical shock.

See Graphic: wc_gr000324

Operating Water Level

Motor Protection System

(Circle thermal protector)

The pump has a built-in motor protection system (circle thermal

protector). If an excessive current is detected or the motor overheats,

for reasons such as the following, the pump will automatically stop

operating regardless of the water level, to protect the motor:

• Change in supply voltage polarity

• Overload

• Open-phase operation or operation under constraint

Note:

Always determine the cause of the problem and resolve it before

resuming operation. Simply repeating cycles of stopping and restarting

will end up damaging the pump. Do not continue operation at very low

lift, low water level, or while the strainer stand is clogged with debris.

Not only will performance suffer, but also such conditions may cause

noise, heavy vibration, and malfunctioning.

Pump Model C.W.L.

PS 3 1500 80 mm (3-1/8")

PS 3 2200 80 mm (3-1/8")

CAUTION

CWL

wc_gr000324

La page charge ...

Wacker Neuson PS32200 Manuel utilisateur

Ce manuel convient également à

Wacker Neuson PS32200 Manuel utilisateur

dans d''autres langues

Documents connexes