Wacker Neuson PSG2500 Manuel utilisateur

Pump

PSG2 500

OPERATOR’S MANUAL

0171940en 002

1008

0171940EN

PSG2 500 Table of Contents

wc_bo0171940en_002TOC.fm 3

Foreword 4

1. Safety Information 5

1.1 Operating and Electrical Safety ............................................................ 6

1.2 Information Labels ................................................................................ 6

2. Operation 7

2.1 Names of Parts ..................................................................................... 7

2.2 Prior to Operation ................................................................................. 8

2.3 Installation ............................................................................................ 8

2.4 Electrical Wiring .................................................................................. 10

2.5 Wiring Diagram ................................................................................... 13

2.6 Operation ............................................................................................ 14

3. Maintenance 17

3.1 Periodic Maintenance Table ............................................................. 17

3.2 Maintenance and Inspection .............................................................. 18

3.3 Disassembly/Reassembly .................................................................. 20

3.4 Disassembly ....................................................................................... 21

3.5 Reassembly ........................................................................................ 22

3.6 Troubleshooting .................................................................................. 23

4. Technical Data 25

4.1 Standard Specifications ...................................................................... 25

4.2 Operating Specifications (60 Hz) ........................................................ 26

4.3 Dimensions ......................................................................................... 27

Foreword

wc_tx000001gb electric.fm 4

Foreword

This manual provides information and procedures to safely operate

and maintain this Wacker Neuson model. For your own safety and

protection from injury, carefully read, understand and observe the

safety instructions described in this manual.

Keep this manual or a copy of it with the machine. If you lose this

manual or need an additional copy, please contact Wacker Neuson

Corporation. This machine is built with user safety in mind; however,

it can present hazards if improperly operated and serviced. Follow

operating instructions carefully! If you have questions about operating

or servicing this equipment, please contact Wacker Neuson

Corporation.

The information contained in this manual was based on machines in

production at the time of publication. Wacker Neuson Corporation

reserves the right to change any portion of this information without

notice.

All rights, especially copying and distribution rights, are reserved.

No part of this publication may be reproduced in any form or by any

means, electronic or mechanical, including photocopying, without

express written permission from Wacker Neuson Corporation.

Any type of reproduction or distribution not authorized by Wacker

Neuson Corporation represents an infringement of valid copyrights

and will be prosecuted. We expressly reserve the right to make

technical modifications, even without due notice, which aim at

improving our machines or their safety standards.

PSG2 500 Safety Information

wc_si000249gb.fm 5

1. Safety Information

This manual contains DANGER, WARNING, CAUTION, NOTICE and

NOTE callouts which must be followed to reduce the possibility of

personal injury, damage to the equipment, or improper service.

This is the safety alert symbol. It is used to alert you to potential

personal injury hazards. Obey all safety messages that follow this

symbol to avoid possible injury or death.

DANGER indicates a hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING indicates a hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION indicates a hazardous situation which, if not avoided, could

result in minor or moderate injury.

NOTICE: Used without the safety alert symbol, NOTICE indicates a

situation which, if not avoided, could result in property damage.

Note: Contains additional information important to a procedure.

DANGER

WARNING

CAUTION

Safety Information PSG2 500

wc_si000249gb.fm 6

1.1 Operating and Electrical Safety

To reduce risk of electric shock, connect only to a properly grounded,

grounding-type receptacle.

Risk of electric shock—this pump has not been investigated for use in

swimming pool areas.

An acceptable motor-control switch shall be provided at the time of

installation according to local codes and regulations.

To reduce risk of electric shock, follow instructions in this manual for

proper installation.

CAUTION: This pump may automatically restart. Prior to working on

the pump or control panel, all supply circuits must be disconnected.

CAUTION: Risk of shock—do not remove cord and strain relief.

If the power source is protected by a fuse, use a time-delay fuse with

this pump.

1.2 Information Labels

Label Meaning

A nameplate listing the model number, item

number, revision number, and serial number is

attached to each unit. Please record the

information found on this plate so it will be

available should the nameplate become lost or

damaged. When ordering parts or requesting

service information, you will always be asked to

specify the model number, item number, revision

number, and serial number of the unit.

WARNING

CAUTION

Menomonee Falls, WI 53051 USA

Model Item No. Rev.

Serial No.

VHz

kWkgMax. L/minMax. m

MADE IN

TAIWAN

HPlbsMax. GPMMax. ft

CUS

L

I

S

T

E

D

R

Phase

C22.2 No. 108-M89

2001993

Conforms to UL Std. 778

Cert. to CAN/CSA Std.

Amp.

Man. Y/M

THERMALLY PROTECTED

INDOORS OR OUTDOORS

CSA ENCLOSURE 3

Wacker Neuson Corporation

PSG2 500 Operation

wc_tx000820gb.fm 7

2. Operation

2.1 Names of Parts

See Graphic: wc_gr004637

Ref. Description Ref. Description

1 Lifting handle 9 Lubricant

2 Coupling 10 Shaft

3 Oil lifter 11 Shaft sleeve

4 Oil plug 12 Oil casing

5 Suction cover 13 V-ring

6 Strainer 14 Impeller

7 Cable assembly 15 Stud bolt

8 Mechanical seal 16 Pump casing

1

2

7

8

9

10

11

12

13

15

16

14

3

4

5

6

wc_gr004637

Operation PSG2 500

wc_tx000820gb.fm 8

2.2 Prior to Operation

When the pump is delivered, first perform the following checks:

• Inspection

While unpacking, inspect the product for damage during shipment, and

make sure all bolts and nuts are tightened properly.

• Specification check

Check the model number to make sure it is the product that was

ordered. Be certain it is the correct voltage and frequency.

Note: If there is any problem with the product as shipped, contact your

nearest dealer or Wacker Neuson representative at once.

• Product specifications

Do not operate this product under any conditions other than those for

which it is specified. Failure to observe this precaution can lead to

electrical shock, current leakage, fire, water leakage or other

problems.

2.3 Installation

If the pump is used for outdoor fountains, garden ponds and similar

places, or to drain a swimming pool, the pump must be supplied by an

isolating transformer or connected to a Residual Current Device (RCD)

with a residual operating current not exceeding 30 mA.

The pump must not be used when people are in the water.

Leakage of pump lubricants may cause pollution of water.

Proper plug must be provided according to local codes and standards.

Refer to wiring diagram.

DO NOT use this pump in liquids other than water, such as oil, salt

water, or organic solvents.

Use with a power supply voltage within ±5% of the rated voltage.

DO NOT use in water temperatures outside the range of 0–40°C (32–

104°F) which can lead to failure, electrical leakage or shock.

DO NOT use in the vicinity of explosive or flammable materials.

Use only in fully assembled state.

Note: Consult your local dealer or Wacker representative before using

with any liquids other than those indicated in this manual.

CAUTION

WARNING

PSG2 500 Operation

wc_tx000820gb.fm 9

Preparing for installation

Before installing the pump at a work site, you will need to have the

following tools and instruments ready:

• Insulation resistance tester (megohmmeter)

• AC voltmeter

• AC ammeter (clamp-on type)

• Bolt and nut tighteners

• Power supply connection tools (screwdriver or box wrench)

Note: Please also read the instructions that come with each of the test

instruments.

Checks to make before installation

• When a grounded plug is used:

Use the megohmmeter to measure the insulation resistance between

the cable assembly prongs and ground.

• When connection leads are used:

With the megohmmeter, measure the insulation resistance between

each core lead and the ground lead.

Reference insulation resistance: 20MW or greater

Note: The reference insulation resistance (20MW or greater) is the

value when the pump is new or has been repaired. For the reference

value after installation, see “Maintenance and Inspection.”

Precautions During Installation

Do not under any circumstances install or move the pump by

suspending it from the cable assembly. The cable may be damaged,

causing electrical leakage, shock, or fire.

When installing the pump, pay close attention to its center of gravity

and weight. If it is not lowered into place correctly, it may fall and be

damaged or cause injury.

When transporting the pump by hand, be sure to employ manpower

commensurate with the weight of the pump. To avoid back injury when

lifting the pump, bend the knees to pick it up rather than bending your

back only.

2.3.1 Avoid dropping the pump or other strong impact. Lift the pump by

holding it firmly with the hands or by attaching a rope or chain to the

handle.

Note: On cable assembly handling, see Electrical Wiring.

2.3.2 Install the pump in a location with sufficient water level, where water

collects readily.

WARNING

CAUTION

Operation PSG2 500

wc_tx000820gb.fm 10

Note: See “Operating water level” for the water level necessary for

operation. The discharge end of the hose should be located higher

than the water surface. If the end of the hose is submerged, water may

flow back to the pump when the pump is stopped; and if the hose end

is lower than the water surface, water may overflow when the pump is

turned off.

2.3.3 The hose should be run as straight as possible, since excessive

bending will hinder the water flow, preventing sufficient lift, and can

even cause the hose to become clogged with earth. If the hose is

crimped near the pump, air can become trapped in the pump and

cause idle running.

If large quantities of earth are sucked up, damage resulting from

friction in the pump can lead to electrical leakage and shock.

2.3.4 Use the pump in the upright position. If there is a risk of the pump

drawing in debris or sediment, operate the pump inside a basket or by

enclosing it in a net.

2.3.5 If used in a permanent installation, where the pump is not readily

accessible after installation, please contact Wacker for a duplicate

nameplate to be installed at the wellhead or on the control box so that

it will be readily visible.

2.4 Electrical Wiring

Performing electrical wiring

Electrical wiring should be performed by a qualified person in accord

with all applicable regulations. Failure to observe this precaution not

only risks breaking the law but is extremely dangerous.

Incorrect wiring can lead to current leakage, electrical shock or fire.

ALWAYS make sure the pump is equipped with the specified overload

protectors and fuses or breakers, so as to prevent electrical shock from

a current leak or pump malfunction.

Operate within the capacity of the power supply and wiring.

Grounding

DO NOT use the pump without first grounding it properly. Failure to

ground it can lead to electrical shock from a current leak or pump

malfunction.

CAUTION

WARNING

CAUTION

PSG2 500 Operation

wc_tx000820gb.fm 11

DO NOT attach the grounding wire to a gas pipe, water pipe, lightning

arrester or telephone grounding wire. Improper grounding can result in

electrical shock.

Connecting the power supply

Before connecting leads to the terminal strip, make certain the power

supply is turned off (circuit breaker, etc.), to avoid electrical shock,

shorting, or unexpected starting of the pump, leading to injury.

Before inserting the power supply plug, make certain the power supply

is turned off (circuit breaker, etc.), to avoid electrical shock, shorting,

or unexpected starting of the pump, leading to injury.

Do not use the pump with the cable assembly or plug connected

loosely, which can result in electric shock, shorting, or fire.

Draw power from a dedicated power outlet rated at 15 A or above.

Sharing the outlet with other equipment may cause overheating at the

branch outlet and could result in fire.

NOTICE: Be sure to use a dedicated power supply with a ground

leakage circuit breaker.

Grounded plug

Connect only to receptacle of proper voltage and current rating

matching that of the plug provided with the cable assembly.

Without Plug

Tighten the ends of the cable assembly securely against the terminal

board. If installation of a grounded plug is required, use only a properly

rated and approved CEE plug and secure the ends of the cable

assembly securely to power and ground terminals in accordance with

the plug manufacturer’s instructions.

See Graphics: wc_gr000242 and wc_gr004659

WARNING

CAUTION

RD

WH

L1

L2

GR

wc_gr004659

G

Operation PSG2 500

wc_tx000820gb.fm 12

Cable Assembly

If it is necessary to extend the cable assembly, use a core size equal

to or larger than the original. This is necessary not only to avoid a

performance drop, but to prevent cable overheating which can result in

fire, electrical leakage or electrical shock.

If a cable with cut insulation or other damage is submerged in the

water, there is a danger of damage to the pump, electrical leakage,

electrical shock, or fire.

Be careful not to let the cable assembly be cut or become twisted. This

may result in damage to the pump, electrical leakage, electrical shock,

or fire.

If it is necessary to submerge the connection wires of the cable

assembly in water, first seal the wires completely in a molded

protective sleeve, to prevent electrical leakage, electrical shock, or fire.

DO NOT allow the cable assembly wires or power supply plug to

become wet.

Make sure the cable does not become excessively bent or twisted, and

does not rub against a structure in a way that might damage it.

If used in a deep-well installation, the cable assembly should be

secured every twenty feet.

CAUTION

PSG2 500 Operation

wc_tx000820gb.fm 13

2.5 Wiring Diagram

See Graphic: wc_gr004640

Ref. Description Ref. Description

1 Capacitor 6 Ground

2 Main coil 7 Circle thermal protector

3 Auxiliary coil 8 Float switch (normally open

contact)

4 Miniature protector 9 Heater

5 Frame grounding

Wire Colors

BK Black RD Red YL Yellow OR Orange

GN Green TN Tan BR Brown PU Purple

BU Blue VIO Violet CL Clear SH Shield

PK Pink WH White GY Gray LB Light blue

RD

1

WH

BK

BU

3

2

5

4

6

GN GN

wc_gr004640

Operation PSG2 500

wc_tx000820gb.fm 14

2.6 Operation

Before starting

2.6.1 Make sure once again that the product is of the correct voltage and

frequency rating.

NOTICE: Using the product at other than rated voltage and frequency

will not only lower its performance but may damage the product.

Note: Confirm the rated voltage and frequency on the model

nameplate.

2.6.2 Confirm the wiring, supply voltage, circuit breaker capacity, and motor

insulation resistance.

Reference insulation resistance = 20 MΩ or greater.

Note: The reference insulation resistance (20 MΩ or greater) is the

value when the pump is new or has been repaired. For the reference

value after installation see Maintenance and Inspection.

2.6.3 The setting on the circuit breaker or other overload protector should be

made in accord with the rated current of the pump.

Note: See Operating Specifications for the rated current of the pump.

2.6.4 When powering the pump with a generator, be certain the generator is

sized to supply the required power for the pump and any other

equipment powered by the generator.

If the power source is protected by a fuse, use a time-delay fuse with

this pump.

Test Operation

NEVER operate the pump while it is suspended in the air. The recoil

may result in injury or other major accident.

NEVER start the pump when people are standing next to it. A current

leak can result in electrical shock.

Run the pump for a short time (3–10 minutes) and confirm the

following:

• Using an ammeter (clamp-on type), measure the operating

current at the L1 and L2 phase wires on the terminal.

COUNTERMEASURE: If the operating current exceeds the rated

value, pump motor overload may be a cause. Make sure the pump has

been installed under proper conditions as described in Installation.

• Using an AC voltmeter (tester), measure voltage at the terminals.

Supply voltage tolerance: within ±5% of rated voltage.

CAUTION

WARNING

PSG2 500 Operation

wc_tx000820gb.fm 15

COUNTERMEASURE: If the supply voltage is outside the tolerance,

possible causes are the power supply capacity or an inadequate

extension cable. Look again at the wiring diagram and make sure the

conditions are proper.

In case of very excessive vibration, unusual noise or odor, turn off the

power immediately and consult your nearest dealer or Wacker

representative. Continuing to operate the pump under abnormal

conditions may result in electrical shock, fire, or current leakage.

Operation

Make sure no extraneous objects such as pins, nails or other metal

objects are sucked into the pump. These can damage the pump or

cause it to malfunction, and can result in electrical shock or electrical

leakage.

When the pump is not used for an extended period, be sure to turn off

the power (circuit breaker, etc.). Deterioration of the insulation may

lead to electrical leakage, electrical shock, or fire.

In case of a power outage, turn off the power to the pump to avoid

having it start unexpectedly when the power is restored, presenting

serious danger to people in the vicinity.

The pump may become hot during operation. Do not touch an

operating pump. Allow the pump to cool before handling.

Pay careful attention to the water level while the pump is operating. Dry

operation may cause the pump to malfunction.

Note: See section Operating water level, for the water level necessary

for operation.

If the protection system operates due to an overload or malfunction,

causing the pump to stop, disconnect the power supply to the pump.

Make sure that the power is completely shut off before proceeding.

Next, unplug the cable assembly from the receptacle or detach it from

the terminals. Then, investigate and remove the cause of the

malfunction before restarting the pump.

CAUTION

WARNING

CAUTION

WARNING

Operation PSG2 500

wc_tx000820gb.fm 16

Operating water level

Do not operate the pump below the C.W.L. (Continuous running Water

Level) indicated below. Failure to observe this condition may result in

damage to the pump, current leakage or electrical shock.

See Graphic: wc_gr004663

CAUTION

wc_gr004663

5 mm

(0.20")

PSG2 500 Maintenance

wc_tx000821gb.fm 17

3. Maintenance

3.1 Periodic Maintenance Table

(1) If the insulation resistance has become noticeably lower than the previous inspection, an inspec-

tion of the motor will be necessary.

(2) See Inspecting Lubricant and Replacing Lubricant in this chapter.

(3) Specialized know-how is required for inspecting and replacing the mechanical seal. Consult your

nearest dealer or Wacker representative.

(4) Consult your nearest dealer or Wacker representative regarding overhauls.

Pump

Weekly

Monthly

Every

1000

hrs.

Every

2000

hrs.

Every

4000

hrs.

Measure insulation resistance.

Reference insulation resistance =

1MW or greater. (1)



Measure operating current.

Compare with rated current.



Measure supply voltage.

Compare with allowable range (within ±5%

of rated voltage).



Pump inspection.

A noticeable drop in performance may indi-

cate a worn or clogged impeller, strainer,

etc. Remove the clogged debris and replace

any worn parts.



Lubricant inspection. (2)



Change lubricant. (2)

(Designated lubricant: SAE 10W/20W, Tur-

bine Oil ISO VG32 or equivalent)



Change mechanical seal. (3)



Overhaul.

This should be carried out even if there are

no problems with the pump. The frequency

depends on how continuously the pump is

in use. (4)



Maintenance PSG2 500

wc_tx000821gb.fm 18

3.2 Maintenance and Inspection

Regular maintenance and inspections are a necessity for continued

efficient functioning of the pump. If any abnormal conditions are

noticed, refer to the Troubleshooting section and take corrective

measures immediately. It is recommended that a spare pump be kept

ready in case of any problems.

Prior to inspecting

Before inspecting the pump, make certain the power supply (circuit

breaker, etc.) is turned off. Then, unplug the cable assembly from the

receptacle or detach it from the terminals. Failure to follow this

precaution may result in a serious accident from electrical shock or

unexpected starting of the pump motor.

3.2.1 Washing the pump

Remove accumulated matter from the surface of the pump and wash

it with clean water. Take special care to remove any debris from the

impeller.

3.2.2 Inspecting the pump exterior

Look for any peeling or chipped paint, and make sure the nuts and

bolts are fastened tightly. Any cracks in the surface should be repaired

by cleaning that area, drying it and then applying a touch-up coating.

Note: Touch-up paint is not supplied. Note that some kinds of damage

or looseness may require that the unit be disassembled for repairs.

Please consult your nearest dealer or Wacker representative.

Storage

When the pump is out of use for an extended period, wash it and dry it

thoroughly, then store it indoors.

Note: Always run a test operation before putting the pump back into

service.

If the pump is left in the water, it should be run a minimum of once a

week.

• Inspecting Lubricant

Remove the oil plug and tilt the pump to drain a small amount of

lubricant. If the lubricant is milky white or has water mixed in with it, the

mechanical seal may be faulty. In this case the pump will need to be

disassembled and repaired.

• Replacing Lubricant

Remove the oil plug and drain all the lubricant, then replace it with the

specified amount.

WARNING

PSG2 500 Maintenance

wc_tx000821gb.fm 19

Note: Worn lubricant and other waste products should be disposed of

by a qualified agent, in accord with applicable laws. The oil plug gasket

should be replaced each time the lubricant is inspected or changed.

See Graphic: wc_gr004661

Replacement Parts

The table lists the parts that need to be replaced periodically. Replace

these using the recommended frequency as a guideline.

Ref. Description Ref. Description

1. Oil inlet 3. Oil plug

2. Gasket 4. Allen wrench

Pump Model Lubricant Capacity

PSG2 500 150 ml (5.1 fl. oz.)

Part Replacement Frequency

Mechanical seal When lubricant in oil compartment becomes milky.

Lubricant (SAE 10W/20W or

equivalent)

Every 2,000 hours or 12 months, whichever comes first.

Packing and O-ring Each time pump is disassembled or inspected.

Sleeve When it becomes worn.

V-ring When it becomes worn, or each time the pump is disas-

sembled or inspected.

wc_gr004661

1

2

3

1

2

3

4

Maintenance PSG2 500

wc_tx000821gb.fm 20

3.3 Disassembly/Reassembly

Before disassembling the pump, make certain the power supply (circuit

breaker, etc.) is turned off. Then, unplug the cable assembly from the

receptacle or detach it from the terminals. To avoid electrical shock,

DO NOT work with wet hands.

NEVER check the operation of any parts (impeller rotation, etc.) by

turning on the power while the unit is partially assembled. Failure to

observe these precautions may result in a serious accident.

DO NOT disassemble or repair any parts other than those designated

here. If repairs are necessary in any other than the designated parts,

consult your nearest dealer or Wacker representative. Improper

repairs can result in electrical leakage, electrical shock, fire, or water

leaks.

After reassembly, ALWAYS perform a test operation before resuming

use of the pump. Improper assembly will cause the pump to

malfunction, resulting in electric shock or water leaks.

The procedure for disassembly and reassembly is shown here to the

extent necessary for impeller replacement. A specialized environment

and facilities are necessary for work on the mechanical seal and the

motor parts. Contact your nearest dealer or Wacker representative in

the event such repairs are necessary.

WARNING

La page charge ...

Wacker Neuson PSG2500 Manuel utilisateur

Wacker Neuson PSG2500 Manuel utilisateur

dans d''autres langues

Documents connexes