Wacker Neuson PSA2800 Manuel utilisateur

Operator’s Manual

Notice d'emploi

Pump

Pompe

PS2-800, PSA2-800,

PSW3-1500

Type

Document

Date

Version

Language

PS2-800, PSA2-800, PSW3-1500

5000187785

0121

05

EN

-FR

5000187785

Copyright

notice

on America Corporation

All rights, including copying and distribution rights, are reserved.

This publication may be photocopied by the original purchaser of the machine. Any other

type of reproduction is prohibited without express written permission from Wacker

Neuson America Corporation.

Any type of reproduction or distribution not authorized by Wacker Neuson America

Corporation represents an infringement of valid copyrights. Violators will be prosecuted.

Trademarks

All trademarks referenced in this manual are the property of their respective owners.

Manufacturer

Wacker Neuson America Corporation

N92W15000 Anthony Avenue

Menomonee Falls, WI 53051 U.S.A.

Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957

www.wackerneuson.com

Original

instructions

This Operator’s Manual presents the original instructions. The original language of this

Operator’s Manual is American English.

PS(A)2 800 / PSW3 1500 Foreword

wc_tx001080gb.fm 3

Foreword

SAVE THESE INSTRUCTIONS—This manual contains important instructions for

the machine models below. These instructions have been written expressly by

Wacker Neuson America Corporation and must be followed during installation,

operation, and maintenance of the machines.

Machines

covered in

this manual

Machine



documentation

 )URPWKLVSRLQWIRUZDUGLQWKHGRFXPHQWDWLRQ:DFNHU1HXVRQ$PHULFD

&RUSRUDWLRQZLOOEHUHIHUUHGWRDV:DFNHU1HXVRQ

 Keep a copy of the Operator’s Manual with the machine at all times.

 Use the separate Parts Book supplied with the machine to order replacement

parts

.

 Refer to the separate Repair Manual for detailed instructions on servicing and

repairing the machine.

 If you are missing any of these documents, please contact Wacker Neuson to

order a replacement or visit www.wackerneuson.com.

 When ordering parts or requesting service information, be prepared to provide

the machine model number, item number, revision number, and serialnumber.

Expectations

for

information in

this manual

 This manual provides information and procedures to safely operate and

maintain the above Wacker Neuson model(s). For your own safety and to

reduce the risk of injury, carefully read, understand, and observe all instructions

described in this manual.

 Wacker Neuson expressly reserves the right to make technical modifications,

even without notice, which improve the performance or safety standards of its

machines.

 The information contained in this manual is based on machines manufactured

up until the time of publication. Wacker Neuson reserves the right to change

any portion of this information without notice.

 The illustrations, parts, and procedures in this manual refer to Wacker Neuson

factory-installed components. Your machine may vary depending on the

requirements of your specific region.

Machine Item Number

PS2 800 0620436

0620442

PSA2 800 0620443

PSW3 1500 0620339

0620444

Foreword PS(A)2 800 / PSW3 1500

4 wc_tx001080gb.fm

Manufacturer’s

approval

This manual contains references to approved parts, attachments, and

modifications. The following definitions apply:

 Approved parts or attachments are those either manufactured or provided by

W

acker Neuso

n.

 Approved modifications are those performed by an authorized Wacker

Neu

son service center according to written instructions published by Wa

cker

Neu

son.

 Unapproved parts, attachments, and modifications are those that do not

meet

the approved criteria.

Unapproved parts, attachments, or modifications may have the following

consequences:

 Serious injury hazards to the operator and persons in the work area

 Permanent damage to the machine which will not be covered under warranty

Contact your Wacker Neuson dealer immediately if you have questions about

approved or unapproved parts, attachments, or modifications.

Table of Contents

PS(A)2 800 / PSW3 1500

wc_bo5000187761_05TOC.fm

5

Foreword 3

1 Safety Information 7

1.1 Signal Words Used in this Manual ....................................................... 7

1.2 Machine Description and Intended Use ............................................... 8

1.3 Operating Safety .................................................................................. 9

1.4 Operating and Electrical Safety ............................................................ 9

1.5 Service Safety .................................................................................... 10

1.6 Labels ................................................................................................. 11

2 Lifting and Transporting 12

3 Installation 13

3.1 Components ....................................................................................... 13

3.2 Preparing the Machine for First Use .................................................. 14

3.3 Application Area ................................................................................. 14

3.4 Preparing for Installation .................................................................... 15

3.5 Checks to Make Before Installation .................................................... 16

3.6 Discharge Fittings ............................................................................... 16

3.7 Electrical Wiring .................................................................................. 17

3.8 Connecting the Power Supply ............................................................ 18

3.9 Cable Assembly ................................................................................. 19

4 Operation 20

4.1 Before Starting ................................................................................... 20

4.2 Operating Water Level ....................................................................... 22

4.3 Emergency Shutdown Procedure ....................................................... 24

Table of Contents

PS(A)2 800 / PSW3 1500

wc_bo5000187761_05TOC.fm

6

5 Maintenance 25

5.1 Periodic Maintenance Schedule ..........................................................25

5.2 Maintenance and Inspection ...............................................................26

5.3 Storage ................................................................................................26

5.4 Lubrication Inspection and Changing Procedures ...............................27

5.5 Replacement Parts ..............................................................................28

5.6 Disassembly and Reassembly ............................................................28

5.7 Disassembly (PS / PSA) ......................................................................29

5.8 Reassembly (PS / PSA) ......................................................................30

5.9 Disassembly (PSW) ............................................................................31

5.10 Reassembly (PSW) .............................................................................32

5.11 Troubleshooting ...................................................................................33

6 Technical Data 34

6.1 Standard Specifications .......................................................................34

6.2 Operating Specifications .....................................................................35

6.3 Dimensions .........................................................................................36

7 Schematics 37

8 AEM Safety Manual 39

wc_si000289gb.fm

7

PS(A)2 800 / PSW3 1500 Safety Information

1 Safety Information

1.1 Signal Words Used in this Manual

This manual contains DANGER, WARNING, CAUTION, NOTICE, and NOTE

signal words which must be followed to reduce the possibility of personal injury,

damage to the equipment, or improper service.

NOTICE: Used without the safety alert symbol, NOTICE indicates a situation

which, if not avoided, could result in property damage.

Note: A Note contains additional information important to a procedure.

This is the safety alert symbol. It is used to alert you to potential personal hazards.

f Obey all safety messages that follow this symbol.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death

or serious injury.

f To avoid death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

f To avoid possible death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

f To avoid possible minor or moderate injury from this type of hazard, obey all

safety messages that follow this signal word.

wc_si000289gb.fm

8

Safety Information PS(A)2 800 / PSW3 1500

1.2 Machine Description and Intended Use

This machine is a submersible water pump. The Wacker Neuson Submersible Pump

consists of an electric motor, an impeller, a strainer, and a metal casing with ports for

water suction and discharge. Power is supplied to the pump through a corded plug or a

hard-wired connection, depending on the installation. The operator connects hoses to

the pump and routes them so that water is pumped from the work area and discharged

into an appropriate location.

This machine is intended to be used for general de-watering applications. This machine

is intended for the pumping of clear water, or water containing solids up to the size

stated within the product’s specifications, and up to the flow, head, and suction lift limits

also stated within the product’s specifications.

This machine has been designed and built strictly for the intended use described

above. Using the machine for any other purpose could permanently damage the

machine or seriously injure the operator or other persons in the area. Machine damage

caused by misuse is not covered under warranty.

The following are some examples of misuse:

 Pumping flammable, explosive, or corrosive fluids

 Pumping hot or volatile fluids that result in pump cavitation

 Operating the pump outside of product specifications due to incorrect diameter

hoses, incorrect length hoses, other inlet or outlet restrictions, or excessive

suction lift or head

 Using the machine as a ladder, support, or work surface

 Using the machine to carry or transport passengers or equipment

 Operating the machine outside of factory specifications

 Operating the machine in a manner inconsistent with all warnings found on the

machine and in the Operator’s Manual.

This machine has been designed and built in accordance with the latest global safety

standards. It has been carefully engineered to eliminate hazards as far as practicable

and to increase operator safety through protective guards and labeling. However, some

risks may remain even after protective measures have been taken. They are called

residual risks. On this machine, they may include exposure to:

 Electric shock from improper electrical connections or high voltage

 Personal injury from improper lifting techniques

 Projectile hazard from discharge

To protect yourself and others, make sure you thoroughly read and understand the

safety information presented in this manual before operating the machine.

wc_si000289gb.fm

9

PS(A)2 800 / PSW3 1500 Safety Information

1.3 Operating Safety

Operator

qualifications

Only trained personnel are permitted to start, operate, and shut down the machine.

They also must meet the following qualifications:

 have received instruction on how to properly use the machine

 are familiar with required safety devices

The machine must not be accessed or operated by:

 children

 people impaired by alcohol or drugs

Personal

Protective

Equipment

(PPE)

Wear the following Personal Protective Equipment (PPE) while operating this

machine:

 Close-fitting work clothes that do not hinder movement

 Safety glasses with side shields

 Hearing protection

 Safety-toed footwear

Replacement

parts

When replacement parts are required for this machine, use only Wacker Neuson

replacement parts or those parts equivalent to the original in all types of

specifications, such as physical dimensions, type, strength, and material.

1.4 Operating and Electrical Safety

To reduce risk of electric shock, connect only to a properly grounded, grounding-

type receptacle.

Risk of electric shock—this pump has not been investigated for use in swimming

pool areas.

An acceptable motor-control switch shall be provided at the time of installation

according to local codes and regulations.

To reduce risk of electric shock, follow instructions in this manual for proper

installation.

CAUTION: This pump may automatically restart. Prior to working on the pump or

control panel, all supply circuits must be disconnected.

CAUTION: Risk of shock—do not remove cord and strain relief.

WARNING

wc_si000289gb.fm

10

Safety Information PS(A)2 800 / PSW3 1500

1.5 Service Safety

Service

training

Before servicing or maintaining the machine:

 Read and understand the instructions contained in all manuals delivered with

the machine.

 Familiarize yourself with the location and proper use of all controls and safety

devices.

 Only trained personnel shall troubleshoot or repair problems occurring with the

machine.

 Contact Wacker Neuson for additional training if necessary.

When servicing or maintaining this machine:

 Do not allow improperly trained people to service or maintain the machine.

Personnel servicing or maintaining the machine must be familiar with the

associated potential risks and hazards.

Personal

Protective

Equipment

(PPE)

Wear the following Personal Protective Equipment (PPE) while servicing or

maintaining this machine:

 Close-fitting work clothes that do not hinder movement

 Safety glasses with side shields

 Hearing protection

 Safety-toed footwear

In addition, before servicing or maintaining the machine:

 Tie back long hair.

 Remove all jewelry (including rings).

Replacing

parts and

labels

 Replace worn or damaged components.

 Replace all missing and hard-to-read labels.

 When replacing electrical components, use components that are identical in

rating and performance to the original components.

 When replacement parts are required for this machine, use only Wacker

Neuson replacement parts or those parts equivalent to the original in all types of

specifications, such as physical dimensions, type, strength, and material.

wc_si000289gb.fm

11

PS(A)2 800 / PSW3 1500 Safety Information

1.6 Labels

A nameplate listing the model number, item number, revi-

sion number, and serial number is attached to each unit.

Please record the information found on this nameplate so it

will be available should the nameplate become lost or dam-

aged. When ordering parts or requesting service informa-

tion, you will always be asked to specify the model number,

item number, revision number, and serial number of the

unit.

CAUTION

Do not attempt to operate this product before reading the

Operator’s Manual and understanding its contents. Mishan-

dling of this product may result in explosion, fire, or electri-

cal shock.

 Do not pull on the power cord or use the power cord to lift

the pump.

 Always use a dedicated ground leakage circuit breaker.

 Be sure to install the ground wire securely.

 Be sure to disconnect the power supply before handling

o

r inspecting the pump.

Never insert your hand into the pump inlet holes while the

pump is connected to the power supply.

Model Item No. Rev.

Serial No.

VHz

kWMax. m Max. L/min kg

MADE IN

TAIWAN

HPMax. ft Max. GPM lbs

C

US

L

I

S

T

E

D

R

Phase

C22.2 No. 108-M89

2001993

Conforms to UL Std. 778

Cert. to CAN/CSA St d.

Amp.

Man. Y/M

THERMALLY PROTECTED

INDOORS OR OUTDOORS

CSA ENCLOSURE 3

wc_tx001953gb.fm

12

Lifting and Transporting PS(A)2 800 / PSW3 1500

2 Lifting and Transporting

Do not under any circumstances install or move the pump by suspending it from

the cable assembly. The cable may be damaged, causing electrical leakage,

shock, or fire.

When installing the pump, pay close attention to its center of gravity and weight. If it

is not lowered into place correctly, it may fall and be damaged or cause injury.

When transporting the pump by hand, be sure to employ manpower commensurate

with the weight of the pump. To avoid back injury when lifting the pump, bend the

knees to pick it up rather than bending your back only.

Avoid dropping the pump or other strong impact. Lift the pump by holding it firmly

with the hands or by attaching a rope or chain to the handle.

WARNING

CAUTION

wc_tx001968gb.fm

13

PS(A)2 800 / PSW3 1500 Installation

3 Installation

3.1 Components

Ref. Description Ref. Description

1 Lifting handle 8 Seal-mechanical

2 Coupling 9 Lubricant

3 Oil lifter 10 Seal-dust

4 Oil plug 11 Sleeve

5 Cover-suction 12 Housing-oil

6 Strainer 13 Wear ring

7 Cable assembly 14 Impeller

1

2

7

8

9

10

11

12

13

14

3

4

5

6

wc_gr010490

2

wc_tx001968gb.fm

14

Installation PS(A)2 800 / PSW3 1500

3.2 Preparing the Machine for First Use

When the pump is delivered, first perform the following checks:

 Inspection

While unpacking, inspect the product for damage during shipment, and make sure

all bolts and nuts are tightened properly.

 Specification check

Check the model number to make sure it is the product that was ordered. Be

certain it is the correct voltage and frequency.

Note: If there is any problem with the product as shipped, contact your nearest

dealer or Wacker Neuson representative at once.

 Product specifications

Do not operate this product under any conditions other than those for which it is

specified. Failure to observe this precaution can lead to electrical shock, current

leakage, fire, water leakage, or other problems.

3.3 Application Area

If the pump is used for outdoor fountains, garden ponds and similar places, or to

drain a swimming pool, the pump must be supplied by an isolating transformer or

connected to a Residual Current Device (RCD) with a residual operating current

not exceeding 30 mA.

The pump must not be used when people are in the water.

Leakage of pump lubricants may cause pollution of water.

Proper plug must be provided according to local codes and standards. Refer to

wiring diagram.

Do not use this pump in liquids other than water, such as oil, salt water, or organic

solvents.

Use with a power supply voltage within ±5% of the rated voltage.

Do not use in water temperatures outside the range of 0–40°C

(32–104°F) which can lead to failure, electrical leakage or shock.

Do not use in the vicinity of explosive or flammable materials.

Use only in fully assembled state.

Note: Consult your local dealer or Wacker Neuson representative before using

with any liquids other than those indicated in this manual.

CAUTION

WARNING

wc_tx001968gb.fm

15

PS(A)2 800 / PSW3 1500 Installation

1. Install the pump in a location with sufficient water level, where water collects

readily.

Note: See “Operating Water Level” for the water level necessary for operation. The

discharge end of the hose should be located higher than the water surface. If the

end of the hose is submerged, water may flow back to the pump when the pump is

stopped; and if the hose end is lower than the water surface, water may overflow

when the pump is turned off.

2. The hose should be run as straight as possible, since excessive bending

will

h

inder the water flow, preventing sufficient lift, and can even cause the hose

to

become clogged with earth. If the hose is crimped near the pump, air can

b

ecome trapped in the pump and cause idle running.

If large quantities of earth are sucked up, damage resulting from friction in the

pump can lead to electrical leakage and shock.

3. Use the pump in the upright position. To prevent th

e pump from becoming

submerged in mud, mount it on a block or other firm base if necessary.

4. If used in a permanent installation, where the pump is no

t readily accessible

after installation, please contact Wacker Neuson for a duplicate nameplate to be

inst

alled at the wellhead or on the control box so that it will be readily visible.

3.4 Preparing for Installation

Before installing the pump at a work site, you will need to have the following tools

and instruments ready:

 Insulation resistance tester (megohmmeter)

 AC voltmeter

 AC ammeter (clamp-on type)

 Bolt and nut tighteners

 Power supply connection tools (screwdriver or box wrench)

Note: Please also read the instructions that come with each of the test instruments.

CAUTION

wc_tx001968gb.fm

16

Installation PS(A)2 800 / PSW3 1500

3.5 Checks to Make Before Installation

 When a grounded plug is used:

Use the megohmmeter to measure the insulation resistance between the cable

assembly prongs and ground.

 When connection leads are used:

With the megohmmeter, measure the insulation resistance between each core lead

and the ground lead.

Reference insulation resistance: 20MΩ or greater

Note: The reference insulation resistance (20M

Ω

or greater) is the value when the

pump is new or has been repaired. For the reference value after installation, see

“Periodic Maintenance Table.”

DO NOT measure the insulation resistance with insulation resistance tester for the

following parts. It will cause damage (Model PSA 2 500).

Improper ways to measure insulation resistance

3.6 Discharge Fittings

This pump series is offered with a variety of discharge fittings. Follow procedures

noted below to assure a proper discharge connection.

Threaded Discharge Fitting (BSP)

Tighten hose coupling or discharge pipe securely and with proper gaskets.

Quick Disconnect Coupling (QD)

Assure coupling is tightened securely to pump discharge fitting and companion

coupling is securely fastened with proper gaskets.

Barbed Discharge Fitting (Barb)

Place hose clamp over hose and push hose to the base of the discharge fitting.

Tighten the hose clamp to secure the hose in place.

1 Between the plug prongs.

2 Between the electrodes on the level relay unit.

3 Between the electrodes on the level relay unit and the plug prongs.

CAUTION

1

2

wc

_

gr000258

3

wc_tx001968gb.fm

17

PS(A)2 800 / PSW3 1500 Installation

3.7 Electrical Wiring

Performing electrical wiring

Electrical wiring should be performed by a qualified person in accord with all

applicable regulations. Failure to observe this precaution not only risks breaking

the law but is extremely dangerous.

Incorrect wiring can lead to current leakage, electrical shock or fire.

Always make sure the pump is equipped with the specified overload protectors and

fuses or breakers, so as to prevent electrical shock from a current leak or pump

malfunction.

Operate within the capacity of the power supply and wiring.

Grounding

Do not use the pump without first grounding it properly. Failure to ground it can lead

to electrical shock from a current leak or pump malfunction.

Do not attach the grounding wire to a gas pipe, water pipe, lightning arrester or

telephone grounding wire. Improper grounding can result in electrical shock.

WARNING

CAUTION

wc_tx001968gb.fm

18

Installation PS(A)2 800 / PSW3 1500

3.8 Connecting the Power Supply

Before connecting leads to the terminal strip, make certain the power supply is

turned off (circuit breaker, etc.), to avoid electrical shock, shorting, or unexpected

starting of the pump, leading to injury.

Before inserting the power supply plug, make certain the power supply is turned off

(circuit breaker, etc.), to avoid electrical shock, shorting, or unexpected starting of

the pump, leading to injury.

Do not use the pump with the cable assembly or plug connected loosely, which can

result in electric shock, shorting, or fire.

Draw power from a dedicated power outlet rated at 15 A or above. Sharing the

outlet with other equipment may cause overheating at the branch outlet and could

result in fire.

NOTICE: Be sure to use a dedicated power supply with a ground leakage circuit

breaker.

Grounded

plug

Connect only to receptacle of proper voltage and current rating matching that of the

plug provided with the cable assembly.

Without Plug

Tighten the ends of the cable assembly securely against the terminal board. If

installation of a grounded plug is required, use only a properly rated and approved

CEE plug and secure the ends of the cable assembly securely to power and

ground terminals in accordance with the plug manufacturer’s instructions.

WARNING

CAUTION

Br

L

L1

L2

G/Y

wc

_

gr000309

G

wc_tx001968gb.fm

19

PS(A)2 800 / PSW3 1500 Installation

3.9 Cable Assembly

If it is necessary to extend the cable assembly, use a core size equal to or larger

than the original. This is necessary not only to avoid a performance drop, but to

prevent cable overheating which can result in fire, electrical leakage or electrical

shock.

If a cable with cut insulation or other damage is submerged in the water, there is a

danger of damage to the pump, electrical leakage, electrical shock, or fire.

Be careful not to let the cable assembly be cut or become twisted. This may result

in damage to the pump, electrical leakage, electrical shock, or fire.

If it is necessary to submerge the connection wires of the cable assembly in water,

first seal the wires completely in a molded protective sleeve, to prevent electrical

leakage, electrical shock, or fire.

Do not allow the cable assembly wires or power supply plug to become wet.

Make sure the cable does not become excessively bent or twisted, and does not

rub against a structure in a way that might damage it.

If used in a deep-well installation, the cable assembly should be secured every 6 m

(20 ft.).

CAUTION

wc_tx001983gb.fm

20

Operation PS(A)2 800 / PSW3 1500

4 Operation

4.1 Before Starting

1. Make sure once again that the product is of the correct voltage and frequency

rating.

NOTICE: Using the product at other than rated voltage and frequency will not only

lower its performance but may damage the product.

Note: Confirm the rated voltage and frequency on the model nameplate.

2. Confirm the wiring, supply voltage, circuit breaker capacity, and motor insulation

resistance.

Reference insulation resistance = 20 MΩ or greater.

Note: The reference insulation resistance (20 MΩ or greater) is the value when the

pump is new or has been repaired. For the reference value after installation see

“Periodic Maintenance Table.”

3. The setting on the circuit breaker or other overload protector should be made in

accord with the rated current of the pump.

Note: See “Operating Specifications” for the rated current of the pump.

4. When powering the pump with a generator, be certain the generator is sized to

supply the required power for the pump and any other equipment powered by

the generator.

Non-Automatic Model (PS2 800, PSW3 1500)

Test Operation

 Do not operate the pump while it is suspended in the air. The recoil may result in

injury or other major accident.

 Do not start the pump when people are standing next to it. A current leak can

result in electrical shock.

Run the pump for a short time (3–10 minutes) and confirm the following:

 Using an ammeter (clamp-on type), measure the operating current at the L1 and

L2 phase wires on the terminal.

COUNTERMEASURE: If the operating current exceeds the rated value, pump

motor overload may be a cause. Make sure the pump has been installed under

proper conditions as described in Installation.

 Using an AC voltmeter (tester), measure voltage at the terminals. Supply volt-

age tolerance: within ±5% of rated voltage.

COUNTERMEASURE: If the supply voltage is outside the tolerance, possible

causes are the power supply capacity or an inadequate extension cable. Look

again at the wiring diagram and make sure the conditions are proper.

In case of very excessive vibration, unusual noise or odor, turn off the power

immediately and consult your nearest dealer or Wacker Neuson representative.

Continuing to operate the pump under abnormal conditions may result in electrical

shock, fire, or current leakage.

WARNING

CAUTION

La page charge ...

Wacker Neuson PSA2800 Manuel utilisateur

Ce manuel convient également à

Wacker Neuson PSA2800 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents