Hinkley 60 Inch Draftsman Manuel utilisateur

hinkley.com

1

60” DRAFTSMANTM

CEILING FAN INSTRUCTION MANUAL

HINKLEY

PAIR WITH HINKLEY APP

DOWNLOAD ON APP STORE or GOOGLE PLAY

CUL Model No. 60-DRAT

LED

WIFI

DC

DC MOTOR

CONTROL

WET

INDOOR / OUTDOOR LED FAN

hinkley.com

2

WE WANT YOU TO LOVE YOUR NEW FAN

SO WE’RE HERE IF YOU HAVE A QUESTION, NEED SOME

HELP OR WANT TO CHAT ABOUT OUR PRODUCTS, SEND

SUGGESTIONS OUR WAY TOO - WE’RE ALWAYS LOOKING TO

MAKE YOUR EXPERIENCE WITH HINKLEY A POSITIVE ONE.

This manual contains complete instructions for the

installation and operation of this fan. It has been

designed to make the installation process as easy as

possible. If you are unfamiliar or uncomfortable with

wiring, please contact a qualiﬁed electrician. If you

need additional assistance or have any questions,

please reach out to us.

For warranty information, visit hinkley.com.

> SERVICE@HINKLEY.COM

> 800.HINKLEY

> LET’S SEE THAT HINKLEY STYLE @HINKLEY

#HINKLEYSTYLE

02 GENERAL INSTALLATION & OPERATING INSTRUCTIONS

03 IMPORTANT SAFETY PRECAUTIONS

03 TOOLS & MATERIALS REQUIRED

04 UNPACKING YOUR FAN

05 PREPARATION

05 INSTALLING THE HANGING BRACKET

06 HANGING THE FAN

08 ELECTRICAL CONNECTIONS

09 FINISHING THE INSTALLATION

10 INSTALLING THE BLADES

10 INSTALLING THE LIGHT KIT PAN

11 INSTALLING THE LED ASSEMBLY AND GLASS SHADE

12 INSTALLING THE WALL CONTROL

14 OPERATION

16 CARE AND CLEANING

16 TROUBLESHOOTING

17 ENERGY GUIDE

17 SPECIFICATIONS

18 HINKLEY APP / WIFI

TABLE OF CONTENTS

WARNING:

Read and follow these instructions carefully and be mindful of all warnings shown throughout.

hinkley.com

2

GENERAL INSTALLATION & OPERATION INSTRUCTIONS

To ensure the success of the installation, be sure to read the instructions and review the diagrams thoroughly before beginning.

To avoid possible electric shock, be sure electricity is turned oﬀ at the main power box before wiring. All electrical connections must be made in

accordance with local codes, ordinances and/or the National Electric Code. If you are unfamiliar with the methods of installing electrical wiring

and products, secure the services of a qualiﬁed and licensed electrician as well as someone who can check the strength of the supportive

ceiling members and make the proper installation(s) and connections.

WARNING: To reduce the risk of ﬁre, electric shock, or other personal injury, mount fan only on an outlet box or supporting system marked

acceptable for fan support of 35 lbs (15.9 kg) or less and use mounting screws provided with the outlet box. Most outlet boxes commonly used

for the support of lighting ﬁxtures are not acceptable for fan support and may need to be replaced. Consult a qualiﬁed electrician if in doubt.

Make sure that your installation site will not allow rotating fan blades to come in contact with any object. Blades should be at least 7 feet from

ﬂoor.

Blades should be attached after motor housing is hung and in place. Fan motor housing should be kept in the carton until ready to be installed

to protect its ﬁnish. If you are installing more than one ceiling fan, make sure that you do not mix fan blade sets, as each blade is part of a

weighted set.

After making electrical connections, spliced conductors should be turned upward and pushed carefully up into outlet box. The wires should be

spread apart with the common conductor and the grounding conductor on one side of the outlet box, and the “HOT” wires on the other side.

Electrical diagrams are for reference only. Light kits that are not packed with the fan must be UL listed and should be installed per the light kit’s

installation instructions.

After fan is completely installed, check to make sure that all connections are secure to prevent fan from falling and/or causing damage or injury.

The fan can be made to work immediately after installation - the bearings are adequately charged with grease so that, under normal conditions,

further lubrication should not be necessary for the life of the fan.

To operate the reverse function on this fan, press the reverse button while the fan is running.

CAUTION: Do not ingest battery - Chemical bum hazard. Keep new and used batteries away from children.

The remote control supplied with a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal bums in just

2 hours and can lead to death.

If the battery compartment does not close securely, stop using the product and keep it away from children.

If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

WARNING: To reduce the risk of ﬁre or electric shock, this fan should only be used with fan speed control part no. JY1126T manufactured by

Satellite Electronic (Zhongshan) Ltd.

Note: Suitable for use in wet locations.

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

IMPORTANT SAFETY PRECAUTIONS

WARNINGS:

• Disconnect power by removing fuse or turning oﬀ circuit breaker before installing the fan and/or optional lighting.

• Support directly from building structure.

• To reduce the risk of ﬁre, electric shock, or personal injury, mount to outlet box marked “acceptable for fan support” and use mounting

screws provided with the outlet box. Most outlet boxes commonly used for the support of lighting ﬁxtures are not acceptable for fan

support and may need to be replaced. Consult a qualiﬁed electrician if in doubt.

• Do not use an incandescent light dimmer. Do not use this fan with any transformer type fan speed control device.

• To reduce the risk of personal injury, do not bend the blade arms when installing them, balancing the blades or cleaning the fan. Do not

insert any objects(s) between rotating fan blades.

NOTE:

The important precautions, safeguards and instructions appearing in this manual are not meant to cover all possible conditions

and situations that may occur. It must be understood that common sense, caution and carefulness are factors which cannot be

built into this product. These factors must be supplied by the person(s) installing, caring for and operating the unit.

TOOLS & MATERIALS REQUIRED

• PHILLIPS SCREWDRIVER

• FLAT SCREWDRIVER

• WRENCH OR PLIERS

• WIRE CUTTERS

• STEP LADDER

• WIRING SUPPLIES AS REQUIRED BY

ELECTRICAL CODE

hinkley.com

4

UNPACKING YOUR FAN

UNPACK YOUR FAN AND CHECK THE CONTENTS.

• Do not discard the carton. If warranty replacement or repair is ever necessary, the fan should be returned in original packing. Remove all

parts and hardware. Do not lay motor housing on its side, or the decorative housing may shift, be bent or damaged.

• Examine all parts. You should have the following:

PACKAGE CONTENTS

1 Hanging Bracket

CA904566FXX2 Ceiling Canopy

3 Trim Ring

4 Downrod Assembly DRK94016FXX

5 Yoke Cover YC905360FXX

6 Fan Housing with Motor

7 Blade Set of 6 BL905360FXX

8 Blade Arm Set of 6 BLI905360FXX

9 LK Pan AP905360FXX

10 16W LED Module E905360LED

11 Shade Assembly GL905360FR

12 Receiver incl. Wire Nuts CWT905360

13

Wall Control w/2032 Battery, Cradle

A, Wall Pate, Face Plate, Mounting

Screws, Cradle B (for ﬂat wall use only)

980014FWH-R

14

Hardware Bag

Hanging bracket hardware, Safety

cable hardware, Blade screws,

Spacers, Blade bracket screws, Blade

balancing kit

MH905360

xx=FAN FINISH

NOTE: Design of parts shown above may look slightly

diﬀerent for your speciﬁc model of fan

3

4

5

6

9

10

11

8

7

1

2

12

13

AC IN

14

PREPARATION

PREPARATION:

Verify you have all parts before beginning the installation. Check pulp

paper insert closely for missing parts. Remove motor from packing. To

avoid damage to ﬁnish, assemble motor on soft padded surface or use

the original pulp paper insert in motor box.

DO NOT LAY MOTOR HOUSING ON ITS SIDE AS THIS COULD RESULT IN

SHIFTING OF MOTOR IN DECORATIVE ENCLOSURE.

INSTALLING THE HANGING BRACKET

CAUTION: To avoid possible electrical shock, be sure electricity is

turned oﬀ at the main power box before wiring. All wiring must be in

accordance with National and Local Electrical Codes and the ceiling fan

must be grounded as a precaution against possible electric shock.

Locate ceiling joist where fan is to be mounted, being sure location

agrees with the requirements in the minimum clearance section

of this guide. Wood joists must be sound and of adequate size to

support 35 pounds (See page 2, items 3 and 4).

If not already present, mount a UL listed outlet box marked

“suitable for fan support” following the instructions provided with

the outlet box. The outlet box must be able to support a minimum

of 35 pounds.

Remove the canopy ring from the canopy by turning the ring

counter-clockwise until it unlocks. Remove the mounting bracket

from the canopy by loosening the four screws on the top of the

canopy. Remove the two non-slotted screws and loosen the

slotted screws. This will enable you to remove the mounting

bracket.

Attach hanging bracket to outlet box using screws provided with

the outlet box.

1

2

3

4

Parts identiﬁcation on assembled fan.

Hanger

Bracket

Flat Washer

Spring Washer

Outlet Box Screw

Outlet Box

Canopy

Trim Ring

Hanger

bracket

Screws

Figure 1

Figure 2

Canopy

Downrod

Yoke cover

Blade

Shade

LK pan

Motor housing

Blade arm (imbedded)

hinkley.com

6

HANGING THE FAN

Remove hanger ball from downrod by loosening set screw in the side of

the hanger ball. Slide hanger ball down and remove cross pin. (Fig. 1)

Carefully support fan body (motor) in its packing with the mounting collar

(where the wires come out) facing upward.

Loosen the security set screw and remove the downrod pin and cotter pin

from the coupling on top of the motor assembly. (Fig. 2)

Carefully feed the electrical lead wires and safety cable from the fan

through the downrod. Thread downrod into coupler until holes align. Insert

downrod pin through holes in mounting collar and downrod; clip cotter pin

through small hole in end of downrod pin to hold downrod in place.

Securely tighten set screw against downrod using a large ﬂat-head

screwdriver to ensure a tight ﬁt against downrod. Tighten nuts against

mounting collar.

1

2

3

4

5

Downro

d

Set screw

Cross pin

H

anger ball

WARNING: Make sure the cross pin is installed well on hanger ball with downrod.

Figure 1

Figure 2

Downrod

Downrod pin

Hook-up (5) Wires

Security Screws

Cotter pin

Top of Fan Body

Mounting Collar

HANGING THE FAN (continued)

Slip the yoke cover, trim ring and canopy onto the downrod.

(Fig. 3)

Slide the hanger ball onto the downrod, insert the cross pin

through the downrod and tighten. Tighten the set screw.

1

2

3Lift ball/downrod/fan into hanger bracket opening.

NOTE: The tab opposite hanger bracket opening should ﬁt

in slot on ball. (Fig. 4)

NOTE:

Fan has 6 feet of hook-up wire in case you

are using a long extension downrod.

Figure 3

Figure 5

Safety Cable

Wood Ceiling Joist

Safety Cable Clamp

Safety Cable Loop

Wood Screw

And Washer

Registration slot

Figure 4

INSTALLATION OF SAFETY CABLE SUPPORT:

Attach the wood screw and the ﬂat washer to the ceiling joist

as shown (do not fully tighten). Slide the cable clamp onto the

safety cable from the fan. Loop the safety cable around the wood

screw that was just attached to ceiling joist. Feed the end of the

cable into the clamp and pull as much cable through as possible.

Firmly tighten screw in the clamp. Cut oﬀ excess cable.

Hanger Ball

Top of Fan Body

Downrod Set screw

Cross pin

Canopy

Trim Ring

Yoke Cover

Hook-up(5) Wires

Ground Wire

hinkley.com

8

ELECTRICAL CONNECTIONS

REMEMBER - Turn oﬀ the power!

NOTE: Control must be installed within 30 feet of fan.

NOTE: For optimal remote performance, keep the WiFi antenna

separated from the receiver antenna.

WARNING: Check to see that all connections are tight, including

ground, and that no bare wire is visible at the wire nuts, except for the

ground wire.

CAUTION: To reduce the risk of electric shock, this fan must be installed

with an isolating wall control/switch.

Insert the receiver into the ceiling mounting bracket with the

ﬂat side of the receiver facing the ceiling. (Fig. 1) For best

performance, make sure the black antenna and WiFi antenna, on

the end of the receiver, remains extended and not tangled with

any of the electrical wires. Place the WiFi antenna on the outside

of the canopy and stick/ﬁx it on the ceiling.

Make wire connections from the fan to the receiver unit. For this

step use the bundle of 5 wires on the receiver. (Fig. 3)

Connect the BROWN fan wire to the BROWN receiver wire.

Connect the GRAY fan wire to the GRAY receiver wire.

Connect the ORANGE fan neutral wire to the ORANGE receiver

neutral wire.

Connect the WHITE fan neutral wire to the WHITE receiver neutral

wire.

Connect the BLUE fan neutral wire to the BLUE receiver neutral

wire.

Connect the wiring from the ceiling to the receiver unit. (Use the

2 wire bundle on the receiver.) Secure with supplied wire nuts.

Connect the BLACK building supply wire to the BLACK receiver

wire.

Connect the WHITE receiver neutral wire to the WHITE building

neutral wire.

Connect the COPPER building ground wire to the 4 YELLOW/

GREEN ground wires from the fan and receiver.

1

2

3

Figure 1

Figure 3

Hanger

bracket

Receiver

GREEN

BLK(AC IN)

WH(AC IN)

Receiver

BLUE

WHITE

BROWN

GRAY

ORANGE

BLUE

WHITE

BROWN

GRAY

ORANGE

BLK

WH

Ceiling

GROUND

Outlet bo

x

YELLOW+GREEN

Figure 2

WiFi antenna

Receiver

Screw (not included)

FINISHING THE INSTALLATION

Align the locking slots of the ceiling canopy with the two

screws in the mounting plate. Push up to engage the slots and

turn clockwise to lock in place. Immediately tighten the two

mounting screws ﬁrmly.

Install the remaining two mounting screws into the holes in the

canopy and tighten ﬁrmly.

Install the trim ring by aligning the ring’s slots with the screws

in the canopy. Rotate the trim ring clockwise to lock in place.

1

2

3

WARNING:

Make sure the hook on the hanging bracket properly sits in the groove in the hanger ball

before attaching the canopy to the bracket by turning the housing until it drops into place.

Hanger

bracket

Ceiling Fan

Outlet Box

Canopy

Trim Rin

g

Screw

hinkley.com

10

INSTALLING THE BLADES

Install the blade to blade bracket by using the screws and

spacers provided .

Tighten each screw securely.

Install the blade assembly to motor by inserting the blade

bracket into the slot of the ﬂywheel, aligning the holes on blade

bracket with the holes on the ﬂywheel, install the blade bracket

with screws provided. Tighten screw securely.

Repeat steps 1,2 & 3 for the remaining blades.

NOTE:

Remove any rubber supports that are

installed for shipping.

1

2

3

INSTALLING THE LIGHT KIT PAN

CAUTION: To reduce the risk of electrical shock, disconnect the

electrical supply circuit to the fan before installing the light kit.

Loosen but do not remove two of three mounting screws from

the fan motor assembly; Remove one mounting screw.

Push the light kit pan up to the fan motor assembly so that

the two loosened screw heads ﬁt into the keyhole slots. Turn

the light kit pan clockwise, tightened the screws. Re-install the

screw that was removed in step 1 and tighten ﬁrmly.

1

2

4

LK Pan

Screws

Screws Blade Arm

Screws

Spacer

Blades

INSTALLING THE LED ASSEMBLY AND GLASS SHADE

CAUTION: To reduce the risk of electrical shock, disconnect the

electrical supply circuit to the fan before installing the light kit.

Remove one screw from the light kit pan and loosen, but do

not remove the other two screws. Connect the wires from

the light kit ﬁtter assembly to the wires from the fan motor

assembly by connecting the molded adaptor plugs together.

Carefully tuck all wires and splices into the switch cap.

Push the light kit assembly up so that the two loosened screw

heads ﬁt into the keyhole slots. Turn the light kit assembly

clockwise, tighten the screws. Reinstall the screw that was

removed in step 1 and tighten ﬁrmly.

Place the glass shade into the light kit pan, aligning the three

ﬂat areas on the top of the glass shade with the three raised

dimples in the light kit pan. Turn the glass shade clockwise

until it stops.

1

2

3

LED Assembly

LK Pan

Glass Shade

LK Pan

Figure 1

Figure 2

hinkley.com

12

INSTALLING THE WALL CONTROL

Select a desired location. Use the wall plate to mark the

location of the mounting holes. Plastic wall anchors or

mounting screws are needed for this application. (Fig. 1)

Seat the cradle B into the wall plate. Secure the wall plate to

the wall using the provided hardware.

Snap the face plate cover onto the wall bracket.

Remote transmitter will be held in place with built in magnets.

1

2

3

4

Option 1. Flat Surface Installation

Remove the existing wall plate and the old switch from the wall

outlet box.

Seat the cradle A into the wall plate. (Fig. 2)

Connect the black lead wires from the switch in the cradle A to

the black wires in the switch box. Hot input wire to one of the

cradle A switch leads. Power lead to the fan is connected to

the remaining switch lead.

Connect the wall plate / cradle A assembly to the wall outlet

box using the supplied hardware.

Snap the face plate cover onto the wall bracket.

Remote transmitter will be held in place with built in magnets.

1

2

3

4

Option 2. For Single Gang Box

5

6

HIRO Control System

Transmitter

Face plate

Wall plate Cradle B

Wall

Plastic

anchor

Outlet box

Transmitter

Face plate

Wall plate

Cradle A

Figure 1 Figure 2

REMEMBER to turn oﬀ the power before you begin.

NOTE: 1. Control must be installed within 30 feet of fan.

2. Secures to any surface or application: ﬂat wall, single

gang box, multi gang box.

INSTALLING THE WALL CONTROL (continued)

Remove the existing wall plate and old switch from the wall

outlet box. (Fig. 3)

Connect the black lead wires from the switch in cradle A to

the black wires in the switch box. Hot input wire to one of the

cradle switch leads. Power lead to the fan is connected to the

remaining switch lead. (Fig. 4)

Attach cradle A to the wall switch box using supplied hardware.

Attach the multi-gang face plate (not included) to the switch

set in the wall outlet box. Cradle A Hinkley switch will ﬁt in any

standard decora face plate.

1

2

3

4

Option 3. For Multi-Gang Wall Switch Box

NOTE: Remote transmitter will be held in place with built in magnets.

HIRO Control System

Figure 3

Figure 4

Outlet box

Face plate

Switch

Outlet box

Transmitter

Face plate

Cradle A

hinkley.com

14

OPERATION

Your DC brushless motor is equipped with an

automatically learned type remote control.

There is no frequency switches on the receiver

or transmitter. The fan can start to use once

the pairing process is done.

Remove the panel from the transmitter and

then install one 2032 battery (included). You

need to use a coin to open or close the battery

cover. To prevent damage to transmitter,

remove the battery if not use for long periods

of time (Fig. 1)

This product contains a lithium button/coin cell

battery. If a new or used lithium button/coin cell

battery is swallowed or enters the body, it can

cause severe internal burns and can lead to

death in as little as 2 hours. Always completely

secure the battery compartment. If the battery

compartment does not close securely, stop

using the product, remove the batteries,

and keep it away from children. IF you think

batteries might have been swallowed or placed

inside any part of the body, seek immediate

medical attention.

The batteries shall be disposed of properly,

including keeping them away from children;

Even used cells may cause injury.

WARNING: Chemical Burn Hazard.

Keep batteries away from children.

button:

Press this button and release instantly

to turn on or oﬀ the light.

button:

Press and hold to dim or brighten

lights to the desired level and release.

button:

Press this button to set fan wind

direction up or down.

button:

Press button for turn on and setting

1-6 fan speed.

button:

Press this button to turn the fan on/oﬀ.

Signal light (Fig. 2)

1

2

3

4

5

6

NOTE: If installing/pairing more than

one fan in an area, the power must be

disconnected from all fans except the

one fan being paired.

With the fan’s power oﬀ, restore power to

the fan. Press and hold “ ” button for

about 5 seconds and release. If optional

light kit is installed, the light kit will ﬂash

three times and the motor spin up for

10 seconds on low speed. The fan has

completed the pairing process with the

wall control and is ready for use.

NOTE: A single fan can be controlled

with asmany as 3 wall controls in

one room. Every control will need to

repeat the pairing process based on

instructions above and all controls must

be within 30 feet of the fan.

Pairing Process

HIRO Control System

ON

OFF

Figure 1

Figure 2

Signal light

OPERATION (continued)

IMPORTANT: To operate the reverse function on this fan, press the reverse button while the fan is running.

Summer Mode (forward):

A DOWNWARD airﬂow creates a cooling eﬀect as shown in Figure 3. This allows you to set your air conditioner on a warmer setting

without aﬀecting your comfort.

Winter Mode (Reverse):

An UPWARD airﬂow moves warmer air oﬀ the ceiling area as shown in Figure 4. This allows you to set your heating unit on a cooler

setting without aﬀecting your comfort.

1

2

3

Summer Mode and Winter Mode Operation

Figure 3 Figure 4

Summer Mode

(Counter Clockwise Direction)

Winter Mode

(Clockwise Direction)

hinkley.com

16

CARE AND CLEANING

Periodically it may be necessary to re-tighten blade to blade arm screws or blade arm to motor screws to prevent clicking or humming sound

during operation. This is especially true in climates with broad temperature and humidity ranges.

When dusting the blades, you must support the blade to prevent bending - no pressure should be applied to the blades. If you experience

any ﬂaws in the operation of your fan, please check the following points.

TROUBLESHOOTING

CAUTION:

Switch oﬀ power supply before carrying out any of these checks.

Fan Will Not Start

Fan Sounds Noisy

Fan Wobbles

Remote Control

Malfunction.

PROBLEM

1. Check main and branch circuit breakers and/or fuses.

2. Check line wire connections to fan housing wiring. Make sure forward/reverse switch is set to one or the other

position, not stuck in between.

3. Check to make sure the dip switches from the transmitter and receiver are set to the same frequency.

1. Check and make sure that all screws in motor housing are snug (but not over tight).

2. Check that the screws securing blade arms to the motor are tight.

3. Check that wire connectors in switch housing are not rattling against each other or the interior wall of the switch

housing.

4. Check that all glassware is ﬁnger tight and that bulb(s) are well held in the sockets, if a light kit is used.

5. Check that the canopy is ﬁrmly attached to hanging bracket and not vibrating against ceiling.

1. Check that all blades are ﬁrmly screwed into blade arms. Check that all blade arms are ﬁrmly secure to the

motor.

2. Check to make sure that light kit (if present) is ﬁrmly attached to switch housing and that all glassware and

shades are fastened properly. Wobble can also result from even the smallest deviations in distance from blade

tip to blade tip.

3. If measurements from blade tip to blade tip are not equal, loosen screws connecting blade to blade arm one at a

time and adjust blade(s) so that distances are equal.

4. Interchanging adjacent blades may redistribute mass and result in smoother operation. Blade arms can be bent

slightly to restore same pitch to all blades if a blade is diﬀerent than the other blades when viewed edge on.

5. Most wobble can be traced to a loose electrical box or mounting bracket. Make sure these are tight and the ball

is completely seated in the bracket.

6. Use the enclosed Blade Balancing Kit if the blade wobble is still noticeable.

WARNING: To reduce the risk of personal injury, do not bend the blade arm while installing, balancing the blades, or

cleaning the fan. Do not insert foreign objects between rotating fan blades.

1. Do not connect the fan with a wall mounted variable speed control(s).

2. Make sure the dip switches are set correctly.

ENERGY GUIDE SPECIFICATIONS

AVERAGE PERFORMANCE AND ENERGY INFORMATION

PERFORMANCE

SPECIFICATIONS

STANDARD

HIGH SPEED LOW SPEED

Airﬂow (CFM) 8389 2816

Energy Use (Watts) 32.95 3.88

Airﬂow Eﬃciciency (CFM/W) 254.5 725.7

Energy Costs (Yearly) $6

Amps 0.55 0.12

RPMs 143 50

hinkley.com

18

SCAN FOR ADDITIONAL DETAILS

DOWNLOADING THE HINKLEY APP

In addition to the included wall control, you can control your Hinkley

fan through the Hinkley app.

• To use the Hinkley app, download it for free from the App Store or

Google Play.

• Open the Hinkley app where you will be prompted to create an

account.

• Enter all necessary information to create an account.

• After account is created you will receive a veriﬁcation code email to

ﬁnish setting up the Hinkley app (Check spam folder if email is not

received).

• Conﬁrm Bluetooth is enabled to allow the fan and Hinkley app to

connect to each other.

• Click add a device on the home screen and select desired fan.

• The Hinkley app will then have you enter in WiFi name and

password.

• Click done on the Hinkley app to complete connecting the fan.

• The Hinkley app will have options on the main screen for fan

speeds, dimming and setting timers.

• Scan the QR code below for more information on the Hinkley app

operation.

HINKLEY SMART FAN OPTIONS:

La page charge ...

Hinkley 60 Inch Draftsman Manuel utilisateur

Hinkley 60 Inch Draftsman Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents