Extron ZRTP Pro Series Manuel utilisateur

Extron
Marque
Extron
Modèle
ZRTP Pro Series
Taper
Manuel utilisateur
1
IMPORTANT:
Go to www.extron.com for the
complete user guide and installation
instructions before connecting the
product to the power source.
www.extron.com
Wall Mount Zoom Room Controller • Setup Guide
Mounting the Touchpanel
The touchpanels can be wall-mounted, either using a UL-listed junction box, an external wall box, or directly into drywall or furniture.
Suitable mounting accessories can be found at www.extron.com.
ATTENTION:
• Do not install the touchpanels in a re resistant rated wall or partition assembly.
• Ne pas installer les écrans tactiles dans un mur résistant au feu ou une cloison.
• All structural steps and electrical installation must be performed by qualied personnel in accordance with local and national
building codes and electrical codes.
• Toute étape structurelle et installation électrique, doit être effectuée par un personnel qualié, conformément aux codes du
bâtiment, aux codes incendie et sécurité, et aux codes électriques, locaux et nationaux.
With a Wall Box or Junction Box
Some local building codes require the touchpanel to be
mounted in a junction box. Junction boxes or wall boxes must
be purchased separately.
With a wall box
1. Install a junction box or wall box (see gure 1, 1),
following the instructions provided by the manufacturer.
2. Fasten the mounting plate to the wallbox (2) with the
provided screws. Use mounting holes that are appropriate
to the junction box you are using (see gure 2).
NOTES: Extron provides:
• Four 3/4” #6-32 Philips pan head screws for
mounting to US junction boxes
• Two 16 mm M 3.5 Philips pan head screws for
mounting to MK junction boxes
• EU junction boxes are usually provided with
their own screws.
3. Run and connect cables to the back of the touchpanel
(see Rear Panel Features on the following page).
4. The mounting plate has four hooks (3), one in each
corner. Position the touch panel so that the four mounting
slots in the rear of the touchpanel align (see figure 3,D,
on the following page) with these hooks.
5. Move the touchpanel inward and downward so that
touchpanel sits securely on the hooks and the tongue at
the bottom of the mounting plate (see inset, gure 1, 4)
sits in the groove in the bottom of the touchpanel (5).
6. Fasten the touchpanel to the mounting plate with the lock
screw (6).
Without a junction box
If the wall box is not required by local building codes, you can
mount the touchpanel directly into drywall.
1. Place the mounting plate against the wall or furniture
in a suitable location and ensure that it is level. Use the
mounting plate as a template to mark the wall.
2. Cut a hole 3.5 inches (89 mm) wide x 2.0 inches (51 mm)
high to pass cables through the wall.
3. Use the MK slots and drill the two pilot holes (gure 2).
Extron recommends using two Molly bolts or SnapToggle
bolts.
4. Secure the mounting plate to the wall (gure 1, 2).
5. Complete the installation as described in steps 3 through
6 in the previous section.
TOP
e
Back View
12
3
4
5
6
4
Figure 1. Mounting the Touchpanel with a Junction Box
NORTH
AMERICAN
NORTH
AMERICAN
NORTH
AMERICAN
NORTH
AMERICAN
EU
MK
EU
EU EU
MK
3.5" (89 mm)
2.0"
(51 mm)
Figure 2. Touchpanel Mounting Plate
figure 1
2
Wall Mount Zoom Room Controller • Setup Guide (Continued)
Rear Panel Features
C
C
CA
A
AB
B
B
E
E
E
F
F
F
G
G
G
I
I
IJ
J
J K
K
K
H
H
H
D
D
D
D
D
D
D
D
D
D
D
D
Figure 3. Rear Panel
A Menu Button— Allows user to enter or exit the setup menu.
B Reset Button— Allows the user to carry out a factory firmware reset.
C Reset LED— Not used in this application.
D Mounting Slots — Four, one in each corner. The hooks on the corners of the mounting plate (see figure 1, 3, on the
previous page) fit into these slots for wall mounting.
E Digital Input Monitoring Port — This two-pole captive screw port (1 = signal and G = ground) monitors digital input with or
without a +5 VDC pull-up.
F LAN/PoE Connector — Connect the touchpanel to a PoE power injector (not provided) using a twisted pair cable,
terminated with an RJ-45 connector. Connect the power injector to the LAN through a nework switch. An Extron IP Link Pro
control processor must also be connected to the same network as the TouchLink Pro touchpanel.
ATTENTION:
• The touchpanel is Power over Ethernet (PoE 802.3af, class 3) compliant. Do not power on the touchpanels until you
have read the Attention in the “Connecting Power” section of the TLP Pro 525, 725, and 1025 Series User Guide.
• L’écrans tactiles est compatible avec l’alimentation POE via Ethernet (PoE 802.3af, classe 3). Ne branchez pas les
écrans tactiles avant d’avoir lu la mise en garde dans la section «Connecting Power » du TLP Pro 525, 725, and 1025
Series User Guide.
figure 3
NOTE: The touchpanel is shipped without a power injector. The power
injector must be purchased separately.
Figure 4 shows the Extron XTP PI 100. Your power injector may look different.
G USB Port — Compatible with USB 2.0.
H Rear Panel Status Lights — Six, three on each side of the panel.
I Speaker — A single speaker provides audible feedback for the user.
100-240V
~
50-60Hz
0.4A MAX
XTP
PWR
XTP PWR
To network switchTo touchpanel
Figure 4. XTP PI 100
J Slot for Mounting Plate — The tongue at the bottom of the mounting plate (see figure 1, 4, on the previous page) fits into
this slot, for wall mounting.
K Mounting Screw — Tightens against the tongue of the mounting plate to secure the touchpanel.
3
Configuration
1. When the device is powered on for the rst time, select Zoom Rooms Controller and click Next.
Figure 5. Select a Use for the Device
2. Click the settings icon (gure 6, 1).
Figure 6. Click Settings Icon
4
Wall Mount Zoom Room Controller • Setup Guide (Continued)
3. Click System Settings (see gure 7, 1).
Figure 7. Settings Menu
The Settings menu opens.
4. Click System (see gure 8, 1).
Figure 8. Settings Menu
figure 8
5
The System menu allows you to congure Date & Time and Language.
Figure 9. System Menu
5. Click Languages & input and use the options to select the language used by the application.
6. Return to the System menu and click Date & time. Use the options to set date and time automatically, or to set date, time, and
time zone manually. You can also toggle between a 12-hour or 24-hour clock.
7. Return to the Settings page and click Network (see figure 8, 2, on the previous page).
8. Use the toggle switch to select DHCP enabled or disabled.
If DHCP is enabled, the unit Host Name can be congured. All other network settings are read-only.
If DHCP is disabled, consult your network administrator to obtain a valid network IP address, Gateway address, Subnet
mask, and DNS server.
NOTE: For more information about using the setup menu to configure the touchpanel, see the Zoom Room Controller User
Guide, which is available at www.extron.com.
68-3744-51 Rev. A
07 23
Wall Mount Zoom Room Controller • Setup Guide (Continued)
© 2022 - 2023 Extron — All rights reserved. www.extron.com
All trademarks mentioned are the property of their respective owners.
Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92905, 800.633.9876
For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the
Extron Safety and Regulatory Compliance Guide on the Extron website.
Updating Firmware
1. Open Toolbelt.
2. Discover or manually add the device.
Figure 10. Toolbelt — Discover Devices
3. Select one or more devices to update from the Device list.
• Single device selection — <Right click> on a single device and select Update Firmware.
• Multiple device selection — to select multiple devices:
a. Hold down <Shift> and click on a range.
b. <Right click> and select Update Firmware or click on the Update Firmware icon in the Actions column.
4. Open the Firmware Uploader window by clicking Tools > Firmware Uploader... .
Figure 11. Toolbelt — Firmware Loader
5. Enter the credentials for each device if prompted.
6. Click Begin. Firmware Uploader begins to upload the selected rmware to the selected device(s).
The update process goes through the following states:
• Idle — no upload taking place
• Uploading — pre-installation
• Verification — start of installation
• Installation — installing selected rmware version on device
• Completion — rmware upload successful
For more information about using Toolbelt to update rmware, see the Toolbelt Help File at www.extron.com.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Extron ZRTP Pro Series Manuel utilisateur

Extron
Marque
Extron
Modèle
ZRTP Pro Series
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes