Extron TLP Pro 525T Manuel utilisateur

Taper
Manuel utilisateur
TLP Pro 525, 725, and 1025 Series
User Guide
TouchLink
®
TouchLink Pro Touchpanel Control Systems
68-2831-01 Rev. F
09 20
Safety Instructions
Safety Instructions • English
WARNING: This symbol, ,when used on the product, is
intended to alert the user of the presence of uninsulated dangerous
voltage within the product’s enclosure that may present a risk of electric
shock.
ATTENTION: This symbol, , when used on the product, is intended
to alert the user of important operating and maintenance (servicing)
instructions in the literature provided with the equipment.
For information on safety guidelines, regulatory compliances, EMI/EMF
compatibility, accessibility, and related topics, see the Extron Safety and
Regulatory Compliance Guide, part number 68-290-01, on the Extron
website, www.extron.com.
Sicherheitsanweisungen • Deutsch
WARNUNG: Dieses Symbol auf dem Produkt soll den Benutzer
darauf aufmerksam machen, dass im Inneren des Gehäuses dieses
Produktes gefährliche Spannungen herrschen, die nicht isoliert sind und
die einen elektrischen Schlag verursachen können.
VORSICHT: Dieses Symbol auf dem Produkt soll dem Benutzer in
der im Lieferumfang enthaltenen Dokumentation besonders wichtige
Hinweise zur Bedienung und Wartung (Instandhaltung) geben.
Weitere Informationen über die Sicherheitsrichtlinien, Produkthandhabung,
EMI/EMF-Kompatibilität, Zugänglichkeit und verwandte Themen finden Sie in
den Extron-Richtlinien für Sicherheit und Handhabung (Artikelnummer
68-290-01) auf der Extron-Website, www.extron.com.
Instrucciones de seguridad • Español
ADVERTENCIA: Este símbolo, , cuando se utiliza en el producto,
avisa al usuario de la presencia de voltaje peligroso sin aislar dentro del
producto, lo que puede representar un riesgo de descarga eléctrica.
ATENCIÓN: Este símbolo, , cuando se utiliza en el producto, avisa
al usuario de la presencia de importantes instrucciones de uso y
mantenimiento recogidas en la documentación proporcionada con el
equipo.
Para obtener información sobre directrices de seguridad, cumplimiento
de normativas, compatibilidad electromagnética, accesibilidad y temas
relacionados, consulte la Guía de cumplimiento de normativas y seguridad
de Extron, referencia 68-290-01, en el sitio Web de Extron, www.extron.com.
Instructions de sécurité • Français
AVERTISSEMENT : Ce pictogramme, , lorsqu’il est utilisé sur le
produit, signale à l’utilisateur la présence à l’intérieur du boîtier du
produit d’une tension électrique dangereuse susceptible de provoquer
un choc électrique.
ATTENTION : Ce pictogramme, , lorsqu’il est utilisé sur le produit,
signale à l’utilisateur des instructions d’utilisation ou de maintenance
importantes qui se trouvent dans la documentation fournie avec le
matériel.
Pour en savoir plus sur les règles de sécurité, la conformité à la
réglementation, la compatibilité EMI/EMF, l’accessibilité, et autres sujets
connexes, lisez les informations de sécurité et de conformité Extron, réf.
68-290-01, sur le site Extron, www.extron.com.
Istruzioni di sicurezza • Italiano
AVVERTENZA: Il simbolo, , se usato sul prodotto, serve ad
avvertire l’utente della presenza di tensione non isolata pericolosa
all’interno del contenitore del prodotto che può costituire un rischio di
scosse elettriche.
ATTENTZIONE: Il simbolo, , se usato sul prodotto, serve ad
avvertire l’utente della presenza di importanti istruzioni di funzionamento
e manutenzione nella documentazione fornita con l’apparecchio.
Per informazioni su parametri di sicurezza, conformità alle normative,
compatibilità EMI/EMF, accessibilità e argomenti simili, fare riferimento
alla Guida alla conformità normativa e di sicurezza di Extron, cod. articolo
68-290-01, sul sito web di Extron, www.extron.com.
Instrukcje bezpieczeństwa • Polska
OSTRZEŻENIE: Ten symbol, , gdy używany na produkt, ma na celu
poinformować użytkownika o obecności izolowanego i niebezpiecznego
napięcia wewnątrz obudowy produktu, który może stanowić zagrenie
porażenia prądem elektrycznym.
UWAGI: Ten symbol, , gdy używany na produkt, jest przeznaczony do
ostrzegania użytkownika ważne operacyjne oraz instrukcje konserwacji
(obsługi) w literaturze, wyposażone w sprzęt.
Informacji na temat wytycznych w sprawie bezpieczeństwa, regulacji
wzajemnej zgodności, zgodność EMI/EMF, dostępności i Tematy pokrewne,
zobacz Extron bezpieczeństwa i regulacyjnego zgodności przewodnik, część
numer 68-290-01, na stronie internetowej Extron, www.extron.com.
Инструкция по технике безопасности Русский
ПРЕДУПРЕЖДЕНИЕ: Данный символ, , если указан
на продукте, предупреждает пользователя о наличии
неизолированного опасного напряжения внутри корпуса
продукта, которое может привести к поражению
электрическим током.
ВНИМАНИЕ: Данный символ, , если указан на продукте,
предупреждает пользователя о наличии важных инструкций
по эксплуатации и обслуживанию в руководстве,
прилагаемом к данному оборудованию.
Для получения информации о правилах техники безопасности,
соблюдении нормативных требований, электромагнитной
совместимости (ЭМП/ЭДС), возможности доступа и других
вопросах см. руководство по безопасности и соблюдению
нормативных требований Extron на сайте Extron: ,
www.extron.com, номер по каталогу - 68-290-01.
安全说明 简体中文
警告 产品上的这个标志意在警用户该产品机内有暴露的危险 电压,
电危险。
注意 产品上的这个标志意在提示用户设备随附的用户手册中有
重要的操作和维护(维修说明。
关于我们产品的安全指南、遵循的规范、EMI/EMF 的兼容性、无障碍
使用的特性等相关内容,敬请访问 Extron 网站 , www.extron.com,参见
Extron 安全规范指南,产品编号 68-290-01
Copyright
© 2017-2020 Extron. All rights reserved. www.extron.com
All trademarks mentioned are the property of their respective owners..
Trademarks
All trademarks mentioned in this guide are the properties of their respective owners.
The following registered trademarks (
®
), registered service marks (
SM
), and trademarks (
TM
) are the property of RGBSystems, Inc. or Extron
(see the current list of trademarks on the Terms of Use page at www.extron.com):
Registered Trademarks
(
®
)
Extron, Cable Cubby, ControlScript, CrossPoint, DTP, eBUS, EDID Manager, EDID Minder, eLink, Flat Field, FlexOS, Glitch Free, Global
Configurator, Global Scripter, GlobalViewer, Hideaway, HyperLane, IP Intercom, IP Link, Key Minder, LinkLicense, LockIt, MediaLink, MediaPort,
NAV, NetPA, PlenumVault, PoleVault, PowerCage, PURE3, Quantum, ShareLink, Show Me, SoundField, SpeedMount, SpeedSwitch,
StudioStation, System INTEGRATOR, TeamWork, TouchLink, VideoLounge, V-Lock, VN-Matrix, VoiceLift, WallVault, WindoWall, XPA, XTP, XTP
Systems, and ZipClip
Registered Service Mark
(SM)
: S3 Service Support Solutions
Trademarks
(
)
AAP, AFL (Accu-RATE Frame Lock), ADSP (Advanced Digital Sync Processing), Auto-Image, AVEdge, CableCover, CDRS (Class D Ripple
Suppression), Codec Connect, DDSP (Digital Display Sync Processing), DMI (Dynamic Motion Interpolation), Driver Configurator, DSP
Configurator, DSVP (Digital Sync Validation Processing), EQIP, Everlast, FastBite, Flex55, FOX, FOXBOX, IP Intercom HelpDesk, MAAP,
MicroDigital, Opti-Torque, PendantConnect, ProDSP, QS-FPC - QuickSwitch Front Panel Controller, Room Agent, Scope-Trigger, SIS - Simple
Instruction Set, Skew-Free, SpeedNav, Triple-Action Switching, True4K, True8K, Vector™ 4K, WebShare, XTRA, and ZipCaddy
안전 지침 • 한국어
경고: 이 기호 가 제품에 사용될 경우, 제품의 인클로저 내에 있는
접지되지 않은 위험한 전류로 인해 사용자가 감전될 위험이 있음을
경고합니다.
주의: 이 기호 가 제품에 사용될 경우, 장비와 함께 제공된 책자에 나와
있는 주요 운영 및 유지보수(정비) 지침을 경고합
니다.
안전 가이드라인, 규제 준수, EMI/EMF 호환성, 접근성, 그리고 관련 항목에
대한 자세한 내용은 Extron 웹 사이트(www.extron.com)의 Extron 안전 및
규제 준수 안내서, 68-290-01 조항을 참조하십시오.
安全記事 • 繁體中文
警告: 若產品上使用此符號,是為了提醒使用者產品機殼內存在著
可能會導致觸電之風險的未絕緣危險電壓
注意 品上使用此符號,是為提醒使用設備隨附用戶手冊中
護( )説
有關安全性指導方針法規遵EMI/EMF 相存取範圍和相關主題的詳
訊,請瀏覽 Extron 網站:www.extron.com然後《Extron 安全性與法規
守手冊準則編號 68-290-01
安全上の注意
日本語
警告: この 製品上に表示されている場合は、筐体内に絶縁され
いない高電圧が流れ、電の危険があるこていま
意:この が製品上に表示さている場合は、機の取説明書に
載されている重な操作と保()のについてユーザーの
を喚起するものです
安全上の注意、法規厳守、EMI/EMF適合性、その他の関連項
スト イト www.extron.com よ り Extron Safety
and Regulatory Compliance Guide』 ( P/N 68-290-01) をださい
FCC Class A Notice
NOTE: This FCC Class A Notice applies to TLP Pro 725 Series models.
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part15 of the FCC rules. The ClassA limits provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause interference.
This interference must be corrected at the expense of the user.
NOTE: For more information on safety guidelines, regulatory compliances, EMI/EMF
compatibility, accessibility, and related topics, see the Extron Safety and Regulatory
Compliance Guide on the Extron website.
FCC Class B Notice
NOTES:
This FCC Class B Notice applies to the TLP Pro 525M and TLP Pro 1025T models.
This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
This device must accept any interference received, including interference that may
cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part15 of the FCC rules. These limits provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. There is no
guarantee that interference will not occur. If this equipment does cause interference to radio
or television reception, which can be determined by turning the equipment off and on, you
are encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
In order to maintain compliance with FCC regulations, shielded cables must be used with
this equipment. Operation with non-approved equipment or unshielded cables is likely to
result in interference to radio and TV reception. The user is cautioned that changes and
modifications made to the equipment without the approval of the manufacturer could void
the user’s authority to operate this equipment.
NOTE: For more information on safety guidelines, regulatory compliances, EMI/EMF
compatibility, accessibility, and related topics see the Extron Safety and Regulatory
Compliance Guide on the Extron website.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Battery Notice
This product contains a battery. Do not open the unit to replace the battery. If the
battery needs replacing, return the entire unit to Extron (for the correct address, see the Extron
Warranty section on the last page of this guide).
CAUTION: Risk of Explosion if Battery is replaced by an Incorrect Type. Dispose of Used
Batteries According to the Instructions.
ATTENTION : Risque d’explosion. Ne pas remplacer la pile par le mauvais type de pile.
Débarrassez-vous des piles utilisées selon le mode d’emploi.
Class 1 Laser Product
Any service to this product must be carried out by Extron and its qualified service personnel.
CAUTION: Using controls, making adjustments, or performing procedures in a manner
other than what is specified herein may result in hazardous radiation exposure.
NOTE: For more information on safety guidelines, regulatory compliances,
EMI/EMF compatibility, accessibility, and related topics, see the “Extron Safety and
Regulatory Compliance Guide” on the Extron website.
Complies with 21 CFR 1040.10 and 1040.11.
Produit laser de classe1
Si ce produit a besoin d’un quelconque entretient, celui-ci doit être fait par
ExtronElectronics et son personnel qualifié.
ATTENTION : L’utilisation de commandes, la réalisation de réglages, ou l’exécution de
procédures de manière contraire aux dispositions établies dans le présent document,
présente un risque d’exposition dangereuse aux radiations.
Remarque : Pour plus d'informations sur les directives de sécurité, les conformités de
régulation, la compatibilité EMI/EMF, l'accessibilité, et les sujets en lien, consultez le
«Informations de sécurité et de conformité Extron» sur le site internet d'Extron.
Conforme à la section 1040.10 du titre 21 du Code des règlements fédéraux des
États-Unis.
FCC Radio Frequency Interference — Safety Notices
NOTE: The Safety Notices and Industry Canada Notices on this and the following pages
refer to the TLP Pro 525M and TLP Pro 1025T models.
Antenna Warnings
WARNING: The radiated output power of the wireless device is far below the FCC
radio frequency exposure limits. Nevertheless, the unit should be used in such a manner that
the potential for human contact during normal operation is minimized. To avoid the possibility of
exceeding the FCC radio frequency exposure limits, you should keep a distance of at least 20
cm between you (or any other person in the vicinity) and the antenna that is built into the unit.
AVERTISSEMENT: La puissance de sortie rayonnée de l’appareil sans fil est bien
inférieure aux limites d’exposition aux radiofréquences de l’organisme américain FCC
(FederalCommunicationsCommission). Néanmoins, l’unité doit être utilisée de telle sorte que le
contact humain éventuel durant le fonctionnement régulier de l’appareil soit réduit. Afin d’éviter
toute possibilité de dépassement des limites d’exposition aux radiofréquences de la FCC, vous
êtes tenu de conserver une distance de 20cm (8’) au minimum entre vous (ou toute autre
personne située à proximité) et l’antenne intégrée à l’unité.
NOTE: The wireless network device must be installed and used in strict accordance with Extron
Electronic’s instructions as described in the user documentation that comes with the product.
Any other installation or use will violate FCC Part 15 regulations.
Compliance IC
Canada, Industry Canada (IC) Notices
CAN ICES-3 (B)/NMB-3(B)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject
to the following two conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired operation of the
device.
This device complies with RSS247 of Industry Canada.
This Class B digital apparatus complies with Canadian ICES-003, Issue 4, and RSS-247, No 4.
To prevent radio interference to the licensed service, this device is intended to be operated
indoors and away from windows to provide maximum shielding. Equipment (or its transmit
antenna) that is installed outdoors is subject to licensing.
IC Antenna Statement
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a
type and maximum (or lesser) gain approved for the transmitter by Industry Canada.
To reduce potential radio interference to other users, the antenna type and its gain should be so
chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary
for successful communication.
This radio transmitter has been approved by Industry Canada to operate with the antenna types
listed below with the maximum permissible gain and required antenna impedance for each
antenna type indicated. Antenna types not included in this list, having a gain greater than the
maximum gain indicated for that type, are strictly prohibited for use with this device.
Type: Chip
Maximum Peak Gain: 0.5 dBi
Impedance: 50 Ohm
Radio Frequency (RF) Exposure Information
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20 cm
between the antenna and your body.
IC conformité
Canada, avis d’Industry Canada (IC)
CAN ICES-3 (B)/NMB-3(B)
Cet appareil est conforme aux normes des cahiers des charges sur les normes radioélectriques
(CNR) de l’ISDE applicables aux appareils exempts de licence. Son utilisation est subordonnée
aux deux conditions suivantes : (1) Cet appareil ne doit provoquer aucune interférence, et (2) cet
appareil doit accepter toute interférence, y compris l’interférence susceptible de compromettre
son fonctionnement.
Cet appareil est conforme aux normes CNR-247 de l’ISDE.
Cet appareil numérique de classe B est conforme aux normes canadiennes NMB-003, 4ème
édition, et CNR-247, 4ème édition.
Afin d’éviter toute interférence électromagnétique avec le service faisant l’objet d’une licence,
cet appareil doit être utilisé dans des applications intérieures et être éloigné des fenêtres afin de
garantir une protection maximale. L’équipement (ou son antenne d’émission) installé dans des
applications extérieures fait l’objet d’une licence.
Note du ministère ISDE Canada relative aux antennes
En vertu de la réglementation d’Industrie Canada, cet émetteur radio doit être utilisé uniquement
avec une antenne d’un certain type et d’un gain maximal (ou inférieur) approuvé pour l’émetteur
par le ministère. Afin de réduire les éventuelles interférences électromagnétiques préjudiciables
aux autres utilisateurs, il est essentiel de choisir le type d’antenne et son gain de telle sorte que
la puissance isotrope rayonnée équivalente (EIRP) se révèle inférieure aux besoins requis pour
garantir une communication satisfaisante.
Le fonctionnement de l’émetteur radio avec les types d’antenne listés ci-dessous a été approuvé
par Industrie Canada. Le gain maximal autorisé et l’impédance requise pour chaque antenne
sont par ailleurs indiqués. L’utilisation des types d’antenne non inclus dans cette liste, qui
possèdent un gain supérieur au gain maximal indiqué pour chaque type, est strictement interdite
avec cet appareil.
Type : puce électronique
Gain d’antenne maximal : 0.5 dBi
Impédance : 50 ohms
Informations sur les limites d’exposition aux radiofréquences
Cet équipement est conforme aux limites d’exposition aux radiations CNR-102 établies pour un
environnement non contrôlé. Il doit être installé et contrôlé à une distance minimale de 20 cm
entre l’antenne et votre corps.
Conventions Used in this Guide
Notifications
In this user guide, the following are used:
WARNING: Potential risk of severe injury or death.
AVERTISSEMENT : Risque potentiel de blessure grave ou de mort.
CAUTION: Risk of minor personal injury.
ATTENTION : Risque de blessuremineure.
ATTENTION:
Risk of property damage.
Risque de dommages matériels.
NOTE: A note draws attention to important information.
Software Commands
Directory paths that do not have variables are written in the font shown here:
Reply from 208.132.180.48: bytes=32 times=2ms TTL=32
C:\Program Files\Extron
Variables are written in slanted form as shown here:
ping xxx.xxx.xxx.xxx —t
SOH R
Data STX Command ETB ETX
Selectable items, such as menu names, menu options, buttons, tabs, and field names are written
in the font shown here:
From the
File menu, select New.
Click the
OK button.
Specifications Availability
Product specifications are available on the Extron website, www.extron.com.
Extron Glossary of Terms
A glossary of terms is available at www.extron.com/technology/glossary.aspx.
Contents
Introduction............................................................ 1
About the TLP Pro 525, 725 and 1025 Series .........1
Features .................................................................. 2
All Models ...........................................................2
TLP Pro 525M, TLP Pro 725M, and
TLP Pro 1025M .................................................2
Application Diagram ................................................3
Requirements ..........................................................3
Software .............................................................3
Hardware ............................................................3
Installation Overview ........................................... 4
Panel Features ...................................................... 6
Front Panel Features ...............................................6
Rear Panel Features ................................................8
TLP Pro 525T, TLP Pro 725T, and
TLP Pro 1025T Base ............................................11
Connecting Power ................................................12
On-screen Menus ............................................... 14
Setup Menu ..........................................................14
Status ...............................................................14
Network ............................................................ 15
Display .............................................................. 17
Audio ................................................................18
Advanced .........................................................19
Configuration Software ..................................... 21
Configuration Software .......................................... 21
Installing Software .................................................21
Using the Software ................................................ 23
TLP Pro 525, 725, and 1025 Series Web Page .....24
Updating the Firmware ..........................................25
Downloading Firmware ......................................25
Updating Firmware Using the Touchpanel
Web Page ........................................................ 26
Updating Firmware Using Toolbelt .....................26
Mounting ............................................................... 27
Mounting the TLP Pro 525M, 725M,
and 1025M ..........................................................28
Mounting to a Wall Box or Junction Box ............28
Mounting to Drywall ..........................................30
Mounting the Touchpanels with Optional Kits ....30
Mounting the TLP Pro 525T, 725T or 1025T .........30
Desktop Mounting ............................................30
Reference Material ............................................. 31
Best Practices for Cleaning Your
Extron Products ...................................................31
Network Port Requirements and Licensed
Third-Party Software Used by the Touchpanels ....31
Digital I/O Port Cases ............................................ 32
Connecting an Occupancy Sensor to the
Digital I/O Port .................................................32
Connecting a Two-position Switch to the
Digital I/O Port .................................................32
Reset Modes.........................................................33
Use Factory Firmware .......................................33
Reset All IP Settings .......................................... 34
Reset to Factory Defaults ..................................34
Enable or Disable the DHCP Client ....................35
Secure Sockets Layer (SSL) Certificates ................ 35
IEEE 802.1X Certificates ........................................36
Certificate File Requirements .............................36
Private Key File Requirements ...........................36
TLP Pro 525, 725, and 1025 Series Touchpanels • Contents ix
TLP Pro 525, 725, and 1025 Series Touchpanels • Contents x
Introduction
This guide describes the function, installation, and operation of the following Extron Touchlink Pro
Touchpanels:
TLP Pro 525M, TLP Pro 525M NC, TLP Pro 725M, TLP Pro 725M NC, TLP Pro 1025M,
and TLP Pro 1025M NC — wall mountable touchpanels.
The TLP Pro 525M NC, 725M NC, and 1025M NC are streamlined versions of the
TLP Pro 525M, 725M, and 1025M, with a set of features designed to adhere to government
and military security protocols.
A range of mounting options are available for each model (see Mounting on page 27).
TLS 525M, TLS 725M, and TLS 1025M — versions of the TLP Pro 525M, TLP Pro 725M,
and TLP Pro 1025M adapted for use with Room Agent scheduling software. Other than
Mounting, this guide does not apply to the TLS models. See the Room Agent Quick Start
Guide or Room Agent Help File for more information.
TLP Pro 525T, TLP Pro 525T NC, TLP Pro 725T, TLP Pro 725T NC, TLP Pro 1025T
and TLP Pro 1025T NC — touchpanels with weighted bases that allow them to stand on
any suitable flat surface.
The TLP Pro 525T NC, 725T NC, and 1025T NC are streamlined versions of the
TLP Pro 525T, 725T, and 1025T, with a set of features designed to adhere to government
and military security protocols.
Unless otherwise stated:
The term “touchpanel” refers to all models.
“Wall mountable” models refers to the TLP Pro 525M, TLP Pro 525M NC, TLP Pro 725M,
TLP Pro 725M NC, TLP Pro 1025M, and TLP Pro 1025M NC.
“Tabletop” models refers to the TLP Pro 525T, TLP Pro 525T NC, TLP Pro 725T,
TLP Pro 725T NC, TLP Pro 1025T, and TLP Pro 1025T NC.
The term “TLP Pro 725T” refers to the TLP Pro 725T and the TLP Pro 725T NC.
This section discusses the following topics:
About the TLP Pro 525, 725 and 1025 Series
Features
Application Diagram
Requirements
About the TLP Pro 525, 725 and 1025 Series
All of the 525 touchpanels have a 5-inch Active Matrix Color LCD touch display and a screen
resolution of 800x480 (WVGA).
All of the 725 touchpanels have a 7-inch Active Matrix Color LCD touch display and a screen
resolution of 1024x600 (WSVGA).
All of the 1025 touchpanels have 10.1-inch Active Matrix Color LCD touch display and a screen
resolution of 1280x800 (WXGA).
These touchpanels are ideal for any AV application requiring small or medium-sized touchpanels
with flexible mounting options and fully customizable interfaces.
For all TLP Pro models, the screen layout is designed with the Extron GUI Designer software.
The functions are assigned to the screen objects with the Extron Global Configurator Plus and
Professional software or Global Scripter. The user can define the graphics and the functions
associated with those graphics, providing versatility and adaptability to the configuration and
control of an AV system.
TLP Pro 525, 725, and 1025 Series Touchpanels • Introduction 1
The TLS 525M, TLS 725M, and TLS 1025M have the same physical appearance as the
corresponding TLP Pro models but have different firmware. The TLS models can only be used
with the room scheduling software (see the Room Agent Help File and Room Agent User Guide,
which are available at www.extron.com).
Features
All Models
LCD touchscreen — With 24-bit color depth and a vibrant edge-to-edge glass display.
TLP Pro 525 Series — 5-inch touchscreen with 800x480 (WVGA) resolution.
TLP Pro 725 Series — 7-inch touchscreen with 1024x600 (WSVGA) resolution.
TLP Pro 1025 Series — 10.1-inch touchscreen with 1280x800 (WXGA) resolution.
Gorilla Glass
®
screen is tough, scratch, and smudge-resistant — Corning
®
Gorilla
Glass is stronger and more scratch-resistant than standard glass, while maintaining touch
sensitivity, color saturation, and brightness.
Faster, quad-core processing — Provides enhanced response and overall user
experience.
Power over Ethernet (PoE 802.3af, class3) compliance — Allows the touchpanel to
receive power and communication over a single Ethernet cable, eliminating the need for a
local power supply
(power injector sold separately).
Optional Mounting Kits available.
Mounting options for TLP Pro 525M, TLP Pro 725M, and TLP Pro 1025M series:
Mount in a one-gang (TLP Pro 525M Series) or two-gang (TLP Pro 725M and
TLP Pro 1025M Series) junction box or on a wall, lectern, or any flat surface,
including glass, with the optional mounting kits (see www.extron.com).
Mounting options for TLP Pro 525T Series, TLP Pro 725T Series, and
TLP Pro 1025T series:
Sit on a tabletop — fixed 65° viewing angle.
Threaded holes in baseplate allow for secure mounting to a table.
Can be used with the optional SMA-2 Swivel Mount Adapter.
Compatible with the full range of Extron IPL Pro and IPCP Pro control processors
— Allows easy integration into existing systems.
Built-in speaker — Provides audible feedback from button presses.
Light sensor — Adjusts screen brightness as the ambient room lighting changes.
Configurable red and green status lights — Indicate the availability or call status of a
room.
System connection status indicator — The communication LED provides visual
feedback if the touchpanel is not communicating with a control processor.
Automatic clock synchronization — Allows the touchpanel to display the accurate time
and date.
Energy-saving features
Adjustable sleep timer puts the touchpanel into sleep mode.
Motion detector wakes the touchpanel.
Manage, monitor, and control this device remotely — Using GlobalViewer Enterprise
(GVE) Resource Management software.
Fully customizable using Extron control system software — GUI Designer combined
with Global Configurator Plus, Global Configurator Professional, or Global Scripter.
Supports the Extron Control App and Extron Control for Web.
High speed USB 2.0 port — For future expansion.
TLP Pro 525M, TLP Pro 725M, and TLP Pro 1025M
Digital input — Allows connections to a variety of devices, such as sensors and switches.
TLP Pro 525, 725, and 1025 Series Touchpanels • Introduction 2
Application Diagram
POWER
12V
--A MAX
G
Tx Rx RTSCTS
COM 1
G
Tx Rx
COM 2
VCG
VOL
RELAYS
1 2 C
1 2 3 4 G
DIGITAL I/O
PWR OUT = 6W
eBUS
+V+S
-S
G
LAN
IPCP PRO 250
IR/S
S G
Ethernet/PoE
100-240V ~ -- A MAX
1
2
CONFIGURABLE
HDMI
HDMI
5
6
7
8
C
RS-232 IR
RS-232 IR
Tx Rx Tx RxG
Tx Rx Tx RxG
Tx Rx Tx RxG
HDMI
A
B
3
4
INPUTS
OUTPUTS
Tx Rx
RS-232
G
LAN
70V - 100W
RESET
AUDIO INPUTS OUTPUTS
REMOTE
LL1R R
L2
R
3
CLASS 2 WIRING
L4
R
L5R
+48V
+48V
12
LR
VARIABLE
IN1608 MA
2
MIC/LINE
L6
R
SIG LINK
DTP IN
SIG LINK
DTP IN
SIG LINK
DTP OUT
50/60 Hz
RS-232 IR
OVER DTP
OVER DTP
OVER DTP
AMPLIFIED OUTPUT
DTP HDMI 4K 330 Rx
OVER DTP
RS-232
IR
Tx Rx Tx RxG
LR
POWER
12V
0.7A MAX
AUDIO
SIG LINK
DTP IN
OUTPUTS
WiFi
1 234
STANDBY/ON
PQLS HDMIOPEN/CLOSE FL OFF
USB
IR to Blu-ray
RS-232 over DTP
Ethernet
Ethernet
Audio
RS-232
Display
PC
Laptop
Blu-ray Player
Ext
ron
IN
1608 MA
Swit
cher
with
DTP
Ex
tension
TCP/IP
Network
Document
Camera
Extron
FF 220T
Ceiling Speakers
Extron
DTP HDMI 4K
330 Rx
Receiver
CATx Cable
VGA
HDMI HDMI
HDMI
HDMI
Extron
IPCP Pro 250
IP Link Pro
Control Processor
MODEL 80
FLAT PANEL
Extron
TLP Pro 725T
7" TableTop
TouchLink
Pro
Touchpanel
Figure 1. Application Diagram
Requirements
Software
For a complete list of the requirements for running GUI Designer, Global Configurator Plus
and Professional, Global Scripter, Toolbelt, and Room Agent see the Extron web page
(www.extron.com) for that software.
NOTE: These touchpanels are not compatible with GlobalConfigurator 3 or
GUIConfigurator.
Hardware
An Extron IP Link Pro control interface must also be connected to the same network domain as
the TLP Pro TouchLink panel. See www.extron.com for a list of suitable controller processor.
NOTE: These touchpanels are not compatible with Extron IP Link (non-Pro) control
processors.
The TLS models do not require a control processor.
TLP Pro 525, 725, and 1025 Series Touchpanels • Introduction 3
Installation
Overview
This section provides an overview of the installation process. Follow the links for a more detailed
explanation of each step.
1. Before starting to install the TLP Pro models, download and install the latest versions of the
following software:
GUI Designer — For designing layouts for Extron TouchLink Pro touchpanels and third
party touch interfaces.
Global Configurator Plus and Professional — For setting up and configuring the
control processor and touchpanel.
Toolbelt — Provides device discovery, device information, firmware updates,
and configuration of network settings, system utilities, and user management for
TouchLinkPro devices.
Global ScripterProvides an integrated development environment for Extron control
systems programming.
See Configuration Software on page 21.
NOTE: The TLS models do not need to be configured or programmed. Other than
setting network addresses (see Setup Menu on page 14), they are ready to use,
as shipped.
2. Before starting to install the TLP Pro models, obtain the following network information from
your network administrator:
Dynamic Host Configuration Protocol (DHCP) status (on or off). If DHCP is off, you
also require:
IP address Subnet mask Gateway
User name — This can be either admin or user.
Password — The factory configured passwords for all accounts on this device have
been set to the device serial number. Passwords can be changed during configuration.
Passwords are case sensitive.
NOTE: If the device is reset to default settings, the password is the default
password configuration. The default password is extron (for either admin or
user accounts).
MAC address — Make a note of the touchpanel MAC address, which can be found
on the rear panel label (TLP Pro 525M, 725M, or 1025M) or a label on the base
(TLP Pro 525T, 725T, or 1025T).
NOTE: This information is not required for the TLS models.
SSL security certificates and IEEE 802.1X authentication — Extron touchpanels
come with a factory-installed Secure Sockets Layer (SSL) security certificate. IEEE
802.1X authentication is also supported once enabled. See see Secure Sockets Layer
(SSL) Certificates on page 35 or see IEEE 802.1X Certificates on page 36 for
more information.
TLP Pro 525, 725, and 1025 Series Touchpanels • Installation Overview 4
3. Mount and cable the units:
ATTENTION:
Do not power on the touchpanels or control processors until you have read the
Attention about Power over Ethernet (PoE) power supplies (see page 13).
Ne branchez pas les écrans tactiles ou les processeurs de contrôle avant d’avoir
lu la mise en garde sur les sources d’alimentation via Ethernet (PoE) (voir
page 13).
Mount the units.
NOTE:
If you use the setup menu to configure the TLP Pro 525M, 725M, or 1025M
(see step 4, below), configure the touchpanel before mounting as you will
need access to the rear panel Menu button.
The TLS models do not use the setup menu.
Connect cables to the touchpanels (see TLP Pro 525T, TLP Pro 725T, and TLP Pro
1025T Base on page 11 or Rear Panel Features on page 8).
Connect the power cords and power on all devices (see LAN/PoE connector on
page 9 or TLP Pro 525T, TLP Pro 725T, and TLP Pro 1025T Base on page 11).
4. Set up the touchpanels for network communication:
Connect the PC that you are using for setup, the Extron control processor, and the
touchpanel to the same Ethernet subnetwork.
Use the Setup Menu (see page 14) or Toolbelt to set the DHCP status and, if
required, the IP address, subnet mask, gateway, and related settings for the touchpanel.
5. Configure or program the Touchpanels — the GUI Designer Help File, the Global
Configurator Plus and Professional Help File, the Global Scripter Help File, and the Toolbelt
Help File provide step-by-step instructions and detailed information.
The Global Configurator Help File also includes an introduction to that software and sections
on how to start a project and configuration.
Global Scripter provides an Extron-exclusive Python library (ControlScript) and
Global Scripter modules to get you started. See the GlobalScripter Help File for more
information.
NOTE: Frequently touched devices, such as touchscreens, require regular cleaning to
ensure their surfaces remain sanitary. Plastic surfaces and cosmetic finishes can be
damaged by long term exposure to chemicals. For Best Practices for Cleaning Your
Extron Products, see page 31.
TLP Pro 525, 725, and 1025 Series Touchpanels • Installation Overview 5
Panel Features
This section describes the TLP Pro touchpanels:
Front Panel Features
Rear Panel Features
TLP Pro 525T, TLP Pro 725T, and TLP Pro 1025T Base
Front Panel Features
Figure 2 shows the TLP Pro 725M (left) and TLP Pro 725T (right) front panels. The front panels
for all models have the same features and are very similar, apart from size.
B
B
BC
C
C
E
E
E
D
D
DB
B
B
A
A
A
e
B
B
BC
C
CD
D
DB
B
B
A
A
A
E
E
EE
E
E
A
LCD touchscreen
C
Communication LED
E
Front status light
B
Motion sensor
D
Light sensor
Figure 2.
TLP Pro 725M (left) and TLP Pro 725T (right) Front Panels
A
LCD touchscreen
— Made with tough, scratch-resistant touchscreen.
TLP Pro 525 Series — 5-inch touchscreen with 800x480 (WVGA) resolution
TLP Pro 725 Series — 7-inch touchscreen with 1024x600 (WSVGA) resolution
TLP Pro 1025 Series — 10.1-inch touchscreen with 1280x800 (WXGA) resolution
B
Motion sensor
(two) — If the sleep timer has been enabled (see Setup Menu on page 14),
the sensor d
etects motion between 3 to 5 feet (0.9 to 1.5 m) from the touchpanel, and at
least 15° from the center axis (see Configuring the Motion Sensor on page 17)
figure 2
TLP Pro 525, 725, and 1025 Series Touchpanels • Panel Features 6
C
Communication LED
— (see figure 2 on the previous page). Shows the configuration and
connection status of the touchpanel:
Unlit during normal operation (the touchpanel is configured and connected to an
IP Link Pro control processor).
Blinks if the touchpanel has been configured but is not connected to an IP Link Pro
control processor.
Lights steadily if the touchpanel has not been configured.
The indicator can be enabled and disabled, using the Setup Menu (see page 14).
D
Light sensor
— Monitors ambient light level and adjusts screen brightness, based on the
settings configured using the Setup Menu.
E
Front status light
— The TLP Pro 525M, 725M, and 1025M two LEDs (one on each side).
The TLP Pro 525T, 725T, and 1025T have a single LED (in the center of the bottom edge).
The lights can blink or remain lit steadily and they can light red or green. The lights can be
configured (using Global Configurator) or programmed (using Global Scripter) to provide
feedback information about the system using these variables. Different combinations, for
example a red LED lit steadily or a green LED that is blinking, can provide indications about
the system.
For information about setting up these LEDs, see the Global Configurator Help File or the
Global Scripter Help File.
TLP Pro 525, 725, and 1025 Series Touchpanels • Panel Features 7
Rear Panel Features
Figure 3 shows the rear panels of the TLP Pro 525M (top left), TLP Pro 725M (bottom left),
TLP Pro 1025M (top right) and TLP Pro 725T (bottom right). The rear panels of the TLP Pro 525T
and TLP Pro 1025T are similar to the TLP Pro 725T. The rear panels of the NC models are similar
to the corresponding “Non-NC” models.
Many of the features shown on the TLP Pro 525M, 725M, or 1025M rear panels are found on the
TLP Pro 525T, TLP Pro 725T, and TLP Pro 1025T Base (see page 11).
F
F
F
D
D
D
C
C
CA
A
AB
B
B
E
E
E
J
J
JH
H
H
TLP Pro 525M
I
I
I
G
G
G
D
D
D
C
C
CA
A
AB
B
B
E
E
E
F
F
F
G
G
G
H
H
H
I
I
I J
J
J
K
K
K
D
D
D
D
D
D
D
D
D
D
D
D
TLP Pro 725M
C
C
CA
A
AB
B
B
H
H
H
H
H
H
E
E
E
F
F
F
G
G
G
D
D
D
D
D
D
K
K
K
D
D
D
D
D
D
I
I
IJ
J
J
TLP Pro 1025M
K
K
K
G
G
G L
L
L
TLP Pro 725T
A
MENU button
G
USB port (see page 10)
B
RESET button
H
Speaker (see page 10)
C
Reset LED (see next page)
I
Slot for mounting plate (see page 10)
D
Mounting slots (see next page)
J
Mounting screw (see page 10)
E
Digital input monitoring port (see next page)
K
Rear status light (see page 10)
F
LAN/PoE connector (see next page)
L
Cable guide (see page 10)
Figure 3.
TLP Pro 525M (top left), 725M (bottom left), 1025M (top right) and 725T
(bottom right) Rear Panels
A
MENU button (TLP Pro 525M, 725M, and 1025M only) — Activates the setup menu (see
Setup Menu on page 14).
figure 3
Menu button
TLP Pro 525, 725, and 1025 Series Touchpanels • Panel Features 8
B
RESET button (TLP Pro 525M, 725M, and 1025M only) — (see figure 3 on page 8)
Pressing the
RESET button allows the unit to be reset in any of three different modes and
can also be used to toggle between enabling and disabling the DHCP client (see Reset
Modes on page 33).
C
Reset LED (TLP Pro 525M, 725M, and 1025M only) — Provides feedback about the reset
status when the RESET button is pressed (see Reset Modes on page 33).
D
Mounting slots (TLP Pro 525M, 725M, and 1025M only) — The TLP Pro 725M and 1025M
have four, one in each corner. The TLP Pro 525M has two, one in each top corner (see
Mounting the TLP Pro 525M, 725M, and 1025M on page 28).
E
Digital input monitoring port (TLP Pro 525M, 725M, and 1025M only) — This two-pole
captive screw port (
1 = signal and G = ground) monitors digital input with or without a
+5 VDC pull-up.
The table below provides information about the ports:
Digital Input, Pullup Disabled
Logic State Notes
Logic Low Voltage below 2.0 VDC
Logic High Voltage above 2.8 VDC
Digital Input, Pullup Enabled
Logic State Notes
Logic Low Externally shorted to ground
Logic High Open, +5V from pull-up resistor
See Digital I/O Port Cases on page 32, for examples of how these ports function.
F
LAN/PoE connector (TLP Pro 525M, 725M, and 1025M only) — These touchpanels must
be powered by Power over Ethernet (PoE; see Connecting Power on page 12).
ATTENTION:
Do not power on the touchpanels or control processors until you have read the
Attention about Power over Ethernet (PoE) power supplies (see page 13).
Ne branchez pas les écrans tactiles ou les processeurs de contrôle avant d’avoir
lu la mise en garde sur les sources d’alimentation via Ethernet (PoE) (voir
page 13).
NOTE: The touchpanels ship without a power injector. The power injector must be
purchased separately.
An Extron IPL Pro control processor must also be connected to the same network domain
as the TouchLink Pro touchpanel (see the www.extron.com for a list of compatible models).
The network port has two LEDs. The green LED lights steadily to indicate that the
touchpanel is connected correctly to a network. The yellow LED blinks to indicate that data
is being passed to or from the touchpanel.
RESET button
Reset LED
Mounting slots
Digital input monitoring port
LAN/PoE connector
TLP Pro 525, 725, and 1025 Series Touchpanels • Panel Features 9
G
USB port (see figure 3 on page 8) — Compatible with USB 2.0. The TLP Pro 525T,
TLP Pro 725T, and TLP Pro 1025T have a plastic cover that must be removed for access to
the USB port.
H
Speaker (TLP Pro 525M, 725M, and 1025M only) — Provides audible feedback for the user.
The TLP Pro 525M and 725M have a single speaker. The TLP Pro 1025M has two (dual
mono) speakers.
I
Slot for mounting plate (TLP Pro 525M, 725M, and 1025M only) — The tongue at
the bottom of the mounting plate fits into this slot, for wall mounting (see Mounting the
TLP Pro 525M, 725M, and 1025M on page 28).
J
Mounting screw (TLP Pro 525M, 725M, and 1025M only) — Tightens against the tongue
of the mounting plate to secure the touchpanel (see Mounting the TLP Pro 525M, 725M,
and 1025M).
K
Rear status light — The TLP Pro 525M does not have any rear panel status lights. The
TLP Pro 725M has six LEDs (three on each side of the rear panel). The TLP Pro 1025M has
a single LED strip on each side. The TLP Pro 525T, TLP Pro 725T, and TLP Pro 1025T have
a single LED (top center of the rear panel).
The lights can blink or remain steadily lit and they can light red or green. The lights can be
configured (using Global Configurator) or programmed (using Global Scripter) to provide
feedback information about the system using these variables. Different combinations, for
example a red LED lit steadily or a green LED that is blinking, can provide indications about
the system. For information about setting up these LEDs, see the Global Configurator Help
File or the Global Scripter Help File.
The rear panel status lights of the TLP Pro 725M and the TLP Pro 1025M can be disabled,
using the Setup Menu (see page 14).
L
Cable guide (TLP Pro 525T, 725T, and 1025T only) — The Ethernet cable is inserted
through this hole at the back of the base (also see figure 4,
C
, on the following page).
USB port
Speaker
Slot for mounting plate
Mounting screw
Rear status light
Cable guide
TLP Pro 525, 725, and 1025 Series Touchpanels • Panel Features 10
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47

Extron TLP Pro 525T Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues