Extron TLP Pro 300M Manuel utilisateur

TLP Pro 300M
Extron
Marque
Extron
Modèle
TLP Pro 300M
Taper
Manuel utilisateur

Ce manuel convient également à

TLP Pro 300M Series • Setup Guide
Overview
The TLP Pro 300M Series touchpanels are 3.5 inch capacitive touchscreens with a resolution of 320x480 (HVGA) and 18-bit color
depth. They can be mounted, in a portrait orientation, to a standard 1-gang US electrical box.
This guide provides instructions for experienced installers to mount and set up these touchpanels. For complete instructions, see the
TLPPro 300 Series User Guide, at www.extron.com.
Setup Checklist
Get Ready
Download and install the latest version of the following software:
GUI Designer — for designing layouts for Extron TouchLink
®
Pro touchpanels and third party touch interfaces
Global Configurator
®
Professional or Global Configurator Plus — for setting up and conguring the control processor and
touchpanel
Toolbelt — provides device discovery, device information, rmware updates, and conguration of network settings, system
utilities, and user management for TouchLink Pro devices
Global Scripter
®
— provides an integrated development environment for Extron control systems programming
NOTE: All four software programs are available from www.extron.com.
Obtain the following network information from your network administrator:
DHCP status (on or off). If DHCP is off, you must also obtain:
IP address Subnet mask Gateway
Username — This can be either admin or user.
Password — The factory congured passwords for all accounts on this device have been set to the device serial number.
Passwords are case sensitive.
NOTE: If the device is reset to default settings, the password will be the default password conguration. The default
password is extron.
Make a note of the touchpanel MAC address.
Mount and Cable All Devices
Mount the units. There are several mounting options for TouchLink Pro touchpanels (see Mounting on the next page).
Connect the touchpanel to a Power over Ethernet injector (not provided). Extron recommends the XTP PI 100 power injector,
which must be purchased separately.
Connect the power injector to the LAN and power it on.
ATTENTION:
• Do not power on the touchpanels until you have read the ATTENTION in the “Rear Panel Features” section of the
TLPPro 300M Series User Guide.
• Ne branchez pas les écrans tactiles avant d’avoir lu la mise en garde dans la section «Rear Panel Features » du
TLPPro 300M Series User Guide.
Set up the Touchpanels for Network Communication
Connect the PC that you are using for setup, the control processor, and touchpanel to the same Ethernet subnetwork.
Use the Setup Menu (see page 4) or Toolbelt software to set the DHCP status and, if necessary, the IP address, subnet mask,
gateway, and related settings for the touchpanel.
Configure the Touchpanels
Create a graphical user interface with GUI Designer (see GUI Designer Help File for step-by-step instructions).
Associate functions with the graphical user interface features by conguring (see the Global Configurator Help File) or
programming (see the Global Scripter Help File) the system. Global Scripter provides an Extron-exclusive Python library
(ControlScript
®
) and Global Scripter modules to get you started.
1
Product Category
IMPORTANT:
Go to for the
complete user guide and installation
instructions before connecting the
product to the power source.
www.extron.com
Mounting
The following instructions are provided for experienced installers to mount the TLP Pro 300M touchpanel. The touchpanel can be
wall-mounted, either using a standard 1-gang, UL-listed electrical box (must be purchased separately), or directly into drywall or
furniture. Suitable mounting accessories can be found at www.extron.com.
ATTENTION:
• Do not install touchpanels in a re resistant rated wall or partition assembly.
• Ne pas installer les écrans tactiles sur un mur protégé par un dispositif coupe-feu ou dans une cloison.
• All structural steps and electrical installation must be performed by qualied personnel in accordance with local and
national building codes and electrical codes.
• Toute étape structurelle et installation électrique, doit être effectuée par un personnel qualié, conformément aux codes du
bâtiment, aux codes incendie et sécurité, et aux codes électriques, locaux et nationaux.
Mounting With a UL-listed Electrical Box
The UL-listed electrical junction box must be purchased separately.
1. Cut a hole for the junction box at the required location.
2. If you are using the provided tether kit to deter theft, one loop of
the tether kit should be secured to a wall stud with a screw (not
provided)
3. Run cables to the installation site as required.
4. Pass the other end of the tether kit and the cables
through a knock-out in the junction box.
5. Install the junction box by following the instructions
provided by the manufacturer.
6. Secure the metal mounting plate to the junction box,
using the provided screws.
7. Attach cables to the back of the TLP Pro 300M (see
Rear Panel Features on page 3).
8. If a tether kit is being used, loosen the security screw
on the back panel (see figure 4,
F
, on page 3)
just enough to insert the loop of the tether kit.
9. Tighten the screw to clamp the tether in place.
10. Attach the touchpanel to the metal mounting plate. The
touchpanel is held in place by magnets.
NORTH
AMERICA
NORTH
AMERICA
Wall
TLP Pr
o 300M
Metal
Mounting
Plate
Electrical
Junction
Box
#6-32 x ¾"
pan-head screws
Figure 1. Mounting to a UL-Listed Electrical Box
Mounting to Drywall or Furniture
Figure 2 shows how to mount the TLP Pro 300M in drywall. Follow the
same procedure to mount into furniture.
1. Download the TLP Pro 300M Cut-out Template from the Extron
website (www.extron.com). Ensure that it is printed at 100% size,
with no scaling.
2. Remove the cut-out area from the template.
3. Attach the template to the wall in a suitable location, using a level to
ensure the template is aligned correctly.
4. Use the template to mark and remove the cut-out area
(
1
) and drill two holes (
2
) for the screws that secure
the toothed clamping plates.
5. If you are using a tether kit to deter theft, one loop of
the tether kit should be secured to a wall stud.
6. Run cables to the installation site as required.
7. Secure the metal mounting plate to the clamping
plates, using the provided screws. As the screws turn
they tighten the grip of the clamping plates on the
inside surface of the drywall.
8. Attach the tether kit and cables to the touchpanel
and secure the touchpanel to the mounting plate as
described in steps 7 through 10 in the previous section.
NORTH
AMERICA
NORTH
AMERICA
TLP Pr
o 300M
Wall
Metal
Mounting
Plate
Toothed
Clamping
Plate
#6-32 x 1½"
flat-head screws
1
1
1
2
2
2
Figure 2. Mounting to Drywall or Furniture
2
TLP Pro 300M Series • Setup Guide (Continued)
Rear Panel Features
Figure 4 shows the TLP Pro 300M Series rear panel.
A
Status light — Can be programmed to provide system feedback:
z Light red or green z Blink or light continuously
For information about conguring or programming this light, see the
Global Configurator Help File or the Global Scripter Help File.
B
Reset LED — Provides feedback about the reset status when the user
presses the Reset button (for an overview, see Reset Modes: a Brief
Summary, on the next page).
C
Reset Button — Pressing the Reset button allows the unit to be reset in
any of three different modes (see Reset Modes: a Brief Summary).
D
Menu Button — Activates the setup menu (see Setup Menu).
E
Serial Number Label — The serial number is on a label on the side wall of
the back enclosure. The factory congured passwords for all accounts
on this device have been set to the device serial number. Passwords are
case sensitive.
NOTE: If the device is reset to default settings, the password is the
default password conguration. The default password is extron.
F
Security Screw — Used to attach provided tether kit. It requires a Torx
screwdriver (size T8).
G
LAN/PoE Connector — Connect the touchpanel to a PoE power injector
(not provided) using a twisted pair cable, terminated with an RJ-45
B
B
B
C
C
C
D
D
D
G
G
G
H
H
H
E
E
E
A
A
A
F
F
F
Figure 4. TLP Pro 300M Rear Panel
figure 4
connector. Connect the power injector to the LAN through a network switch. An Extron IP Link Pro control processor must also be
connected to the same network as the TouchLink Pro touchpanel.
See Connecting the Power Injector on the next page.
ATTENTION:
• The TLP Pro 300M is Power over Ethernet (PoE 802.3af, class 2) compliant. Do not power on the touchpanels until you
have read the Attention in the “Rear Panel Features” section of the TLP Pro 300M Series User Guide.
• Le TLP Pro 300M supportent l’alimentation via Ethernet (PoE 802.3af, classe 3). Veuillez lire la partie « Attention » dans la
section « Rear Panel Features » du TLP Pro 300M Series User Guide, avant de mettre sous tension les écrans tactiles.
NOTE: These touchpanels are shipped without a power injector. The power injector must be purchased separately.
H
USB Port — One micro-B receptacle supports high-speed USB 2.0.
Front Panel Features
Figure 3 shows the TLP Pro 300M Series front panel.
A
LCD touchscreen — The 3.5-inch, 320x480 resolution touchscreen is made with
Corning
®
Gorilla
®
Glass, which is stronger and more scratch-resistant than standard
glass, while maintaining touch sensitivity, color saturation, and brightness.
B
Motion sensor (2) — Detects motion between three to ve feet from the
touchpanel, and at least 15° from the center axis.
C
Light sensor — Monitors ambient light level and adjusts screen brightness, based
on the settings congured using the Setup Menu (see the next page).
A
A
A
B
B
BC
C
C
Figure 3. TLP Pro 300M Front Panel
3
Product Category
TLP Pro 300M Series • Setup Guide (Continued)
Reset Modes: a Brief Summary
The TLP Pro 300M Series touchpanels offer the following reset modes:
• Use Factory Firmware: Use this mode with Toolbelt software to replace rmware in the event of conicts arising from
uploading a rmware update.
Press and hold the Reset button (see figure 4,
C
) while applying power to the unit.
• Reset All IP Settings: Use this mode to reset all network settings without affecting user-loaded les.
Press and hold the Reset button until the Reset LED (
B
) blinks twice (about 6 seconds). Release
and momentarily press the Reset button again.
• Reset to Factory Defaults: Use this mode to return the touchpanel to factory default settings, including passwords.
Press and hold the Reset button until the Reset LED blinks three times (about 9 seconds). Release
and momentarily press the Reset button again.
NOTES:
• The factory congured passwords for all accounts on this device have been set to
the device serial number. Passwords are case sensitive.
• If the device is reset to default settings, the password will be the default password
conguration. The default password is extron.
• Enable or Disable the
DHCP Client:
Use this mode to toggle between DHCP enabled and DHCP disabled.
Press the Reset button ve times, consecutively. After the fth press, do not press the button again
within 3 seconds. If DHCP was enabled, it is now disabled and the Reset LED blinks three times. If
DHCP was disabled, it is now enabled and the Reset LED blinks six times.
Setup Menu
Figure 6 shows the Setup menu Status screen for the TLP Pro 300M.
Press the Menu button (see figure 4,
D
) to open the Setup menu. Any of the six available
screens (Status, Network, Display, Audio, Project Information, and Advanced) can be
accessed by pressing the menu button in the top left corner of the screen (for more information,
see the TLP Pro 300M Series User Guide).
It may be necessary to scroll down to see all the information on the page (for example, see the
Status screen in gure 6).
STATUS
EXIT
Device Information
Model
Part Number
Firmware
Bootloader
Network
TLP Pro 300M
60-1667-02
1.00.0001-003
1.00.0002
IP Address
192.168.254.251
Figure 6. Setup Menu: Status Screen for TLP Pro 300M
Connecting the Power Injector
The power injector must be purchased separately. Figure 5 shows the
Extron XTP PI 100. Your power injector may look different.
Connect a straight-through Ethernet cable from the power injector to a
switch or router (
1
). This cable carries network information from the
switch or router to the power supply input. A second straight-through
cable (
2
) carries the network information and 48VDC from the power
injector to the touchpanel LAN/PoE connector (see figure 4,
G
, on the
previous page). Connect the IEC power cord to a convenient 100 VAC to
240 VAC, 50-60 Hz power source (see gure 5,
3
).
100-240V
~
50-60Hz
0.4A MAX
XTP
PWR
XTP PWR
To network switchTo touchpanel
1
1122
2
3
3
3
Figure 5. Connecting to a Power Injector
4
68-3146-50 Rev. A
02 20
For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the
Extron Safety and Regulatory Compliance Guide on the Extron website.
For information about replacing and disposing of batteries, see the TLP Pro 300M Series User Guide at www.extron.com.
© 2020 Extron Electronics — All rights reserved. www.extron.com
All trademarks mentioned are the property of their respective owners.
Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Extron TLP Pro 300M Manuel utilisateur

TLP Pro 300M
Extron
Marque
Extron
Modèle
TLP Pro 300M
Taper
Manuel utilisateur
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes