Secure Wireless QNP915PAD2W Manuel utilisateur

QNP915PAD2W
Secure Wireless
Marque
Secure Wireless
Modèle
QNP915PAD2W
Catégorie
Lecteurs de contrôle d'accès
Taper
Manuel utilisateur

Ce manuel convient également à

SW‐ATT‐PAD2WRTL41809 InstallationInstructions
Product Description
The AT&T model number SW-ATT-PAD2W is a proprietary 915MHz
wireless keypad that enables control of all system functions. The
keypad also features a built-in sounder that annunciates system
status information, alarms and troubles. They keypad sounds a
predefined “chirp” and “beep” sound when a button is pressed on the
keypad. For example, the system can be configured so that the
keypad chirps when an entry/exit door is opened and closed. The
keypad annunciates different sounds for fire and intrusion alarms.
Installing/Replacing Batteries
The keypad has four (4) AA batteries that provide twenty-four (24)
hour battery backup. The batteries can be replaced by opening the
battery compartment located on the rear of the unit.
Installing the Keypad
Connect the wires from the AC/DC power adapter to the terminals
on the back side of the keypad, as depicted in Figure 40. And install
four AA batteries. Plug the AC/DC power adapter into AC power
outlet. When powered up, it is ready to be discovered.
Figure 40: Keypad Connection to the AC/DC Adapter and
Installation of AA Batteries
Discovering and Registering the Keypad (Digital Life
Direct)
Follow these steps to discover and register the keypad using DLD:
Step 1. Power up the keypad.
Step 2. Access the “Devices” page.
Step 3. Place the DLC in Discovery Mode (Initializing
Process)
Step 4. Enroll the keypad.
SW‐ATT‐PAD2WRTL41809 InstallationInstructions
Step 5. Review the DLC in Discovery Mode (Discovery in
Process)
Step 6. Confirm device discovery
Regulatory Statements
This equipment has been tested and found to comply with the limits
for Class B Digital Device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures.
Reorient or relocate the receiving antenna
Increase the separation between the equipment and
receiver
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected
Consult the dealer or an experienced radio/TV technician for
help.
Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate
the equipment.
Le présent appareil est conforme aux CNR d’Industrie
Canada applicables aux appareils radio exempts de licence.
exploitation est autorisée aux deux conditions suivantes: (1)
appareil ne doit pas produire de brouillage, et (2) utilisateur
de appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible
en compromettre le fonctionnement.
FCC Compliance Statement
This device complies with FCC
Rules and Regulations as Part 15 devices as well as Industry
Canada license exempt RSS Rules and Regulations. Operation is
subject to the following two (2) conditions: This device may not
cause harmful interference. This device must accept any
interference received, including interference that may cause
undesired operation.
LISTED
  • Page 1 1
  • Page 2 2

Secure Wireless QNP915PAD2W Manuel utilisateur

QNP915PAD2W
Secure Wireless
Marque
Secure Wireless
Modèle
QNP915PAD2W
Catégorie
Lecteurs de contrôle d'accès
Taper
Manuel utilisateur
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Autres documents