Hitachi DH 18DSL Manuel utilisateur
- Catégorie
- Outils électroportatifs
- Taper
- Manuel utilisateur
INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI
AVERTISSEMENT
Une utilisation INCORRECTE OU DANGEREUSE de cet outil motorisé peut entraîner
la mort ou de sérieuses blessures corporelles !
Ce mode d’emploi contient d’importantes informations à propos de la sécurité de
ce produit. Prière de lire et de comprendre ce mode d’emploi AVANT d’utiliser
l’outil motorisé. Garder ce mode d’emploi à la disponibilité des autres utilisateurs
et propriétaires avant qu’ils utilisent l’outil motorisé. Ce mode d’emploi doit être
conservé dans un endroit sûr.
SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL
WARNING
IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily
injury!
This manual contains important information about product safety. Please read
and understand this manual BEFORE operating the power tool. Please keep this
manual available for other users and owners before they use the power tool. This
manual should be stored in safe place.
INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES
ADVERTENCIA
¡La utilización INAPROPIADA O PELIGROSA de esta herramienta eléctrica puede
resultar en lesiones de gravedad o la muerte!
Este manual contiene información importante sobre la seguridad del producto.
Lea y comprenda este manual ANTES de utilizar la herramienta eléctrica. Guarde
este manual para que puedan leerlo otras personas antes de utilizar la herramienta
eléctrica. Este manual debe ser guardado en un lugar seguro.
MODEL Cordless Rotary Hammer
MODÈLE Marteau rotatif sans fil
MODELO Martillo perforador a batería
DH 18DSL
01Eng_DH18DSL_US 2/14/13, 15:171
CONTENTS
English
TABLE DES MATIERES
ÍNDICE
Página
NOMENCLATURA ............................................... 52
ESPECIFICACIONES ............................................ 53
MONTAJE Y OPERACIÓN ...................................... 54
APLICACIONES ................................................... 54
MÉTODO DE EXTRACCIÓN E INSTALACIÓN
DE LA BATERÍA ............................................ 54
MÉTODO DE CARGA .......................................... 54
ANTES DE LA UTILIZACIÓN .............................. 56
ANTES DE LA OPERACIÓN ................................ 56
COMO SE USA .................................................... 57
MANTENIMIENTO E INSPECCIÓN ........................ 61
ACCESORIOS ........................................................... 63
ACCESORIOS ESTÁNDAR ................................. 63
ACCESORIOS OPCIONALES ................................................
63
LISTA DE PIEZAS .................................................... 67
Page
NAME OF PARTS .................................................. 9
SPECIFICATIONS ................................................ 10
ASSEMBLY AND OPERATION ............................... 11
APPLICATIONS ................................................... 11
REMOVAL AND INSTALLATION METHOD
OF BATTERY ................................................ 11
CHARGING METHOD ......................................... 11
BEFORE USE ....................................................... 13
PRIOR TO OPERATION ....................................... 13
HOW TO USE ...................................................... 14
MAINTENANCE AND INSPECTION ....................... 17
ACCESSORIES ......................................................... 19
STANDARD ACCESSORIES ............................... 19
OPTIONAL ACCESSORIES ....................................
19
PARTS LIST .............................................................. 67
Page
CONSIGNES DE SÉCURITÉ IMPORTANTES .... 23
SIGNIFICATION DES MOTS D’AVERTISSEMENT
.... 23
SECURITE ................................................................ 23
AVERTISSEMENTS DE SÉCURITÉ GÉNÉRAUX
CONCERNANT LES OUTILS ÉLECTRIQUES
....... 23
REGLES DE SECURITE SPECIFIQUES ET SYMBOLES ......
25
CONSIGNES DE SÉCURITÉ IMPORTANTES
POUR L’UTILISATION DU MARTEAU
ROTATIF SANS FIL ...................................... 26
CONSIGNES DE SÉCURITÉ IMPORTANTES
POUR LE CHARGEUR DE BATTERIE .......... 26
CONSIGNES DE SÉCURITÉ IMPORTANTES POUR L’UTILISATION
DE LA BATTERIE ET DU CHARGEUR DE BATTERIE ...............
27
PRÉCAUTIONS RELATIVES A LA BATTERIE AU LITHIUM ION ...
28
DESCRIPTION FONCTIONNELLE ........................... 30
Page
NOM DES PARTIES ............................................ 30
SPECIFICATIONS ................................................ 31
ASSEMBLAGE ET FONCTIONNEMENT ................ 32
UTILISATIONS .................................................... 32
MÉTHODE DE RETRAIT ET D’INSTALLATION
DE LA BATTERIE .......................................... 32
MÉTHODE DE RECHARGE ................................. 32
AVANT L’UTILISATION ...................................... 34
AVANT LA MISE EN MARCHE ........................... 34
UTILISATION ....................................................... 36
ENTRETIEN ET INSPECTION .................................. 39
ACCESSOIRES ......................................................... 41
ACCESSOIRES STANDARD ............................... 41
ACCESSOIRES EN OPTION .............................................
41
LISTE DES PIECES ................................................... 67
Français
Español
Página
INSTRUCCIONES IMPORTANTES SOBRE
SEGURIDAD ................................................. 45
SIGNIFICADO DE LAS PALABRAS DE SEÑALIZACIÓN ...
45
SEGURIDAD ............................................................. 45
ADVERTENCIAS DE SEGURIDAD GENERAL DE LA
HERRAMIENTA ELÉCTRICA ..................................
45
NORMAS Y SÍMBOLOS ESPECÍFICOS DE SEGURIDAD
.. 47
INSTRUCCIONES IMPORTANTES DE
SEGURIDAD PARA EL USO DEL
MARTILLO PERFORADOR A BATERÍA ....... 48
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
PARA EL CARGADOR DE BATERÍAS ......... 48
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
PARA LA BATERÍA Y EL CARGADOR DE BATERÍAS ..
49
ADVERTENCIA DE LA BATERÍA DE LITIO ......... 50
DESCRIPCIÓN FUNCIONAL .................................... 52
Page
IMPORTANT SAFETY INSTRUCTIONS ............... 3
MEANINGS OF SIGNAL WORDS ........................ 3
SAFETY ...................................................................... 3
GENERAL POWER TOOL SAFETY WARNINGS ... 3
SPECIFIC SAFETY RULES AND SYMBOLS ......... 5
IMPORTANT SAFETY INSTRUCTIONS FOR
USE OF THE CORDLESS ROTARY
HAMMER ........................................................ 6
IMPORTANT SAFETY INSTRUCTIONS FOR
BATTERY CHARGER ...................................... 6
IMPORTANT SAFETY INSTRUCTIONS
FOR USE OF THE BATTERY AND
BATTERY CHARGER ...................................... 7
CAUTION ON LITHIUM-ION BATTERY ............... 7
FUNCTIONAL DESCRIPTION .................................... 9
01Eng_DH18DSL_US 2/14/13, 15:172
English
3
IMPORTANT SAFETY INSTRUCTIONS
Read and understand all of the safety precautions, warnings and operating instructions in the Instruction Manual
before operating or maintaining this power tool.
Most accidents that result from power tool operation and maintenance are caused by the failure to observe basic
safety rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation
before it occurs, and by observing appropriate safety procedures.
Basic safety precautions are outlined in the “SAFETY” section of this Instruction Manual and in the sections which
contain the operation and maintenance instructions.
Hazards that must be avoided to prevent bodily injury or machine damage are identified by WARNINGS on the
power tool and in this Instruction Manual.
NEVER use this power tool in a manner that has not been specifically recommended by HITACHI.
MEANINGS OF SIGNAL WORDS
WARNING indicates a potentially hazardous situations which, if ignored, could result in death or serious injury.
CAUTION indicates a potentially hazardous situations which, if not avoided, may result in minor or moderate
injury, or may cause machine damage.
NOTE emphasizes essential information.
SAFETY
GENERAL POWER TOOL SAFETY WARNINGS
WARNING:
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated
(cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust.
Power tools create sparks which may ignite
the dust or fumes.
c) Keep children and bystanders away while
operating a power tool.
Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way.
Do not use any adapter plugs with earthed
(grounded) power tools.
Unmodified plugs and matching outlets will
reduce risk of electric shock.
b) Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators.
There is an increased risk of electric shock if
your body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions.
Water entering a power tool will increase the
risk of electric shock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts.
Damaged or entangled cords increase the risk
of electric shock.
e) When operating a power tool outdoors, use
an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces
the risk of electric shock.
f) If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply.
Use of an RCD reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired
or under the influence of drugs, alcohol or
medication.
01Eng_DH18DSL_US 2/14/13, 15:173
English
4
A moment of inattention while operating
power tools may result in serious personal
injury.
b) Use personal protective equipment. Always
wear eye protection.
Protective equipment such as dust mask, non-
skid safety shoes, hard hat, or hearing
protection used for appropriate conditions
will reduce personal injuries.
c) Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool.
Carrying power tools with your finger on the
switch or energising power tools that have
the switch on invites accidents.
d) Remove any adjusting key or wrench before
turning the power tool on.
A wrench or a key left attached to a rotating
part of the power tool may result in personal
injury.
e) Do not overreach. Keep proper footing and
balance at all times.
This enables better control of the power tool
in unexpected situations.
f) Dress properly. Do not wear loose clothing
or jewellery. Keep your hair, clothing and
gloves away from moving parts.
Loose clothes, jewellery or long hair can be
caught in moving parts.
g) If devices are provided for the connection of
dust extraction and collection facilities,
ensure these are connected and properly
used.
Use of dust collection can reduce dust-related
hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application.
The correct power tool will do the job better
and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does
not turn it on and off.
Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools.
Such preventive safety measures reduce the
risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool’s operation.
If damaged, have the power tool repaired
before use.
Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed.
Use of the power tool for operations different
from those intended could result in a
hazardous situation.
5) Battery tool use and care
a) Recharge only with the charger specified by
the manufacturer.
A charger that is suitable for one type of
battery pack may create a risk of fire when
used with another battery pack.
b) Use power tools only with specifically
designated battery packs.
Use of any other battery packs may create a
risk of injury and fire.
c) When battery pack is not in use, keep it away
from other metal objects like paper clips,
coins, keys, nails, screws, or other small
metal objects, that can make a connection
from one terminal to another.
Shorting the battery terminals together may
cause burns or a fire.
d) Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If
contact accidentally occurs, flush with water.
If liquid contacts eyes, additionally seek
medical help. Liquid ejected from the battery
may cause irritation or burns.
6) Service
a) Have your power tool serviced by a qualified
repair person using only identical
replacement parts.
This will ensure that the safety of the power
tool is maintained.
01Eng_DH18DSL_US 2/14/13, 15:174
English
5
WARNING:
Some dust created by power sanding, sawing,
grinding, drilling, and other construction activities
contains chemicals known [to the State of California]
to cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
●
Lead from lead-based paints,
●
Crystalline silica from bricks and cement and other
masonry products, and
●
Arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to filter out microscopic particles.
SPECIFIC SAFETY RULES AND SYMBOLS
1. Wear ear protectors.
Exposure to noise can cause hearing
loss.
2. Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury.
3. Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring.
Cutting accessory contacting a “live” wire may
make exposed metal parts of the power tool
“live”and could give the operator an electric shock.
4. NEVER touch moving parts.
NEVER place your hands, fingers or other body
parts near the tool’s moving parts.
5. NEVER operate without all guards in place.
NEVER operate this tool without all guards or
safety features in place and in proper working
order. If maintenance or servicing requires the
removal of a guard or safety feature, be sure to
replace the guard or safety feature before resuming
operation of the tool.
6. Use right tool.
Don’t force small tool or attachment to do the job
of a heavy-duty tool.
Don’t use tool for purpose not intended —for
example— don’t use circular saw for cutting tree
limbs or logs.
7. NEVER use a power tool for applications other
than those specified.
NEVER use a power tool for applications other than
those specified in the Instruction Manual.
8. Handle tool correctly.
Operate the tool according to the instructions
provided herein. Do not drop or throw the tool.
NEVER allow the tool to be operated by children,
individuals unfamiliar with its operation or
unauthorized personnel.
9. Definitions for symbols used on this tool
V ............... volts
—
---
.............. direct current
no ............ no load speed
---/min ...... revolutions or reciprocation per minute
10. Keep all screws, bolts and covers tightly in place.
Keep all screws, bolts, and plates tightly mounted.
Check their condition periodically.
11. Do not use power tools if the plastic housing or
handle is cracked.
Cracks in the tool’s housing or handle can lead to
electric shock. Such tools should not be used until
repaired.
12. Blades and accessories must be securely mounted
to the tool.
Prevent potential injuries to yourself or others.
Blades, cutting implements and accessories which
have been mounted to the tool should be secure
and tight.
13. NEVER use a tool which is defective or operating
abnormally.
If the tool appears to be operating unusually,
making strange noises, or otherwise appears
defective, stop using it immediately and arrange
for repairs by a Hitachi authorized service center.
14. Carefully handle power tools.
Should a power tool be dropped or struck against
hard materials inadvertently, it may be deformed,
cracked, or damaged.
15. Do not wipe plastic parts with solvent.
Solvents such as gasoline, thinner benzine, carbon
tetrachloride, and alcohol may damage and crack
plastic parts. Do not wipe them with such solvents.
Wipe plastic parts with a soft cloth lightly
dampened with soapy water and dry thoroughly.
16. Keep motor air vent clean.
The tool’s motor air vent must be kept clean so
that air can freely flow at all times. Check for dust
build-up frequently.
17. ALWAYS wear eye protection that meets the
requirement of the latest revision of
ANSI Standard Z87.1.
01Eng_DH18DSL_US 2/14/13, 15:175
English
6
Table 1
RECOMMENDED MINIMUM AWG SIZE FOR
EXTENSION CORDS FOR BATTERY CHARGERS
AC Input Rating Amperes* AWG Size of Cord
Equal to or but less Length of Cord, Feet (Meter)
greater than than 25 (7.5) 50 (15) 100 (30) 150 (45)
02 1818 18 16
23 1818 16 14
34 1818 16 14
IMPORTANT SAFETY INSTRUCTIONS FOR
USE OF THE CORDLESS ROTARY
HAMMER
WARNING:
Death or serious bodily injury could result from
improper or unsafe use of the cordless rotary
hammer. To avoid these risks, follow these basic
safety instructions:
1. NEVER touch the tool bit with bare hands after
operation.
2. NEVER wear gloves made of stuff liable to roll up
such as cotton, wool cloth or string, etc.
3. ALWAYS attach the side handle and securely grip
the Cordless Rotary Hammer.
4. ALWAYS be careful with buried object such as an
underground, wiring.
Touching these active wiring or electric cable with
this tool, you may receive an electric shock.
Confirm if there are any buried object such as
electric cable within the wall, floor or ceiling where
you are going to operate here after.
IMPORTANT SAFETY INSTRUCTIONS FOR
BATTERY CHARGER
WARNING:
Death or serious bodily injury could result from
improper or unsafe use of battery chargers. To
avoid these risks, follow these basic safety
instructions:
READ ALL INSTRUCTIONS
1. This manual contains important safety and
operating instructions for battery charger Model
UC18YRSL.
2. Before using battery charger, read all instructions
and cautionary markings on (1) battery charger,
(2) battery, and (3) product using battery.
3. To reduce risk of injury, charge HITACHI
rechargeable battery type BSL18 series. Other type
of batteries may burst causing personal injury and
damage.
4. Do not expose battery charger to rain or snow.
5. Use of an attachment not recommended or sold
by the battery charger manufacturer may result in
a risk of fire, electric shock, or injury to persons.
6. To reduce risk of damage to electric plug and cord,
pull by plug when disconnecting battery charger.
7. Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise subjected
to damage or stress.
8. An extension cord should not be used unless
absolutely necessary. Use of improper extension
cord could result in a risk of fire and electric shock.
If extension cord must be used make sure:
a. That blades of extension cord are the same
number, size, and shape as those of plug on
battery charger:
b. That extension cord is properly wired and in
good electrical condition; and
c. That wire size is large enough for AC ampere
rating of battery charger as specified in
Table 1.
* If the input rating of a battery charger is given in
watts rather than in amperes, the corresponding
ampere rating is to be determined by dividing the
wattage rating by the voltage rating–for example:
1,250 watts
125 volts
= 10 amperes
9. Do not operate battery charger with damaged cord
or plug-replace them immediately.
10. Do not operate battery charger if it has received a
sharp blow, been dropped, or otherwise damaged
in any way; take it to a qualified serviceman.
11. Do not disassemble battery charger; take it to a
qualified serviceman when service or repair is
required. Incorrect reassembly may result in a risk
of electric shock or fire.
12. To reduce risk of electric shock, unplug charger
from receptacle before attempting any
maintenance or cleaning. Removing the battery
will not reduce this risk.
13. This battery charger might be attached to HITACHI
battery operated tools as a standard accessory. In
this case, please confirm Instruction Manual of the
HITACHI battery operated tools before using the
battery charger.
01Eng_DH18DSL_US 2/14/13, 15:176
English
7
IMPORTANT SAFETY INSTRUCTIONS FOR
USE OF THE BATTERY AND BATTERY
CHARGER
You must charge the battery before you can use the
power tool. Before using the model
UC18YRSL battery charger, be sure to read all
instructions and cautionary statements on it, the battery
and in this manual.
CAUTION:
USE ONLY HITACHI BATTERY TYPE BSL18
SERIES. OTHER TYPES OF BATTERIES MAY
BURST AND CAUSE INJURY!
Follow these instructions to avoid the risk of injury:
WARNING:
Improper use of the battery or battery charger can
lead to serious injury. To avoid these injuries:
1. NEVER disassemble the battery.
2. NEVER incinerate the battery, even if it is
damaged or is completely worn out. The battery
can explode in a fire.
3. NEVER short-circuit the battery.
4. NEVER insert any objects into the battery
charger’s air vents. Electric shock or damage to
the battery charger may result.
5. NEVER charge outdoors. Keep the battery away
from direct sunlight and use only where there is
low humidity and good ventilation.
6. NEVER charge when the temperature is below
32°F (0°C) or above 104°F (40°C).
7. NEVER connect two battery chargers together.
8. NEVER insert foreign objects into the hole for the
battery or the battery charger.
9. NEVER use a booster transformer when charging.
10. NEVER use an engine generator or DC power to
charge.
11. NEVER store the battery or battery charger in
places where the temperature may reach or exceed
104°F (40°C).
12.
ALWAYS
operate charger on standard household
electrical power (120 volts). Using the charger on
any other voltage may overheat and damage the
charger.
13.
ALWAYS
wait at least 15 minutes between charges
to avoid overheating the charger.
14.
ALWAYS
disconnect the power cord from its
receptacle when the charger is not in use.
CAUTION ON LITHIUM-ION BATTERY
To extend the lifetime, the lithium-ion battery equips
with the protection function to stop the output.
In the cases of 1 and 2 described below, when using
this product, even if you are pulling the switch, the motor
may stop. This is not the trouble but the result of
protection function.
1. When the battery power remaining runs out (The
battery voltage drops to about 12V), the motor
stops.
In such case, charge it up immediately.
2. If the tool is overloaded, the motor may stop. In this
case, release the switch of tool and eliminate causes
of overloading. After that, you can use it again.
Furthermore, please heed the following warning and
caution.
WARNING:
In order to prevent any battery leakage, heat
generation, smoke emission, explosion and
ignition beforehand, please be sure to heed the
following precautions.
1. Make sure that swarf and dust do not collect on
the battery.
䡬
During work make sure that swarf and dust do
not fall on the battery.
䡬
Make sure that any swarf and dust falling on the
power tool during work do not collect on the
battery.
䡬
Do not store an unused battery in a location
exposed to swarf and dust.
䡬
Before storing a battery, remove any swarf and
dust that may adhere to it and do not store it
together with metal parts (screws, nails, etc.).
2. Do not pierce battery with a sharp object such
as a nail, strike with a hammer, step on, throw
or subject the battery to severe physical shock.
3. Do not use an apparently damaged or deformed
battery.
4. Do not use the battery in reverse polarity.
5. Do not connect directly to an electrical outlets or
car cigarette lighter sockets.
6. Do not use the battery for a purpose other than
those specified.
7. If the battery charging fails to complete even
when a specified recharging time has elapsed,
immediately stop further recharging.
8. Do not put or subject the battery to high
temperatures or high pressure such as into a
microwave oven, dryer, or high pressure container.
9. Keep away from fire immediately when leakage
or foul odor are detected.
10. Do not use in a location where strong static
electricity generates.
11. If there is battery leakage, foul odor, heat
generated, discolored or deformed, or in any way
appears abnormal during use, recharging or
storage, immediately remove it from the equipment
or battery charger, and stop use.
01Eng_DH18DSL_US 2/14/13, 15:177
English
8
SAVE THESE INSTRUCTIONS
AND
MAKE THEM AVAILABLE TO OTHER USERS
AND
OWNERS OF THIS TOOL!
CAUTION:
1. If liquid leaking from the battery gets into your
eyes, do not rub your eyes and wash them well
with fresh clean water such as tap water and
contact a doctor immediately.
If left untreated, the liquid may cause eye-problems.
2. If liquid leaks onto your skin or clothes, wash well
with clean water such as tap water immediately.
There is a possibility that this can cause skin irritation.
3. If you find rust, foul odor, overheating, discolor,
deformation, and/or other irregularities when using
the battery for the first time, do not use and return
it to your supplier or vendor.
WARNING:
If an electrically conductive foreign object enters the
terminals of the lithium ion battery, a short-circuit may
occur resulting in the risk of fire. Please observe the
following matters when storing the battery.
䡬
Do not place electrically conductive cuttings, nails,
steel wire, copper wire or other wire in the storage
case.
䡬
Either install the battery in the power tool or store
by securely pressing into the battery cover until
the ventilation holes are concealed to prevent
short-circuits (See Fig. 1).
01Eng_DH18DSL_US 2/14/13, 15:178
English
9
Fig. 1
䡬
Battery (BSL1830)
NAME OF PARTS
1. Cordless Rotary Hammer (DH18DSL)
FUNCTIONAL DESCRIPTION
NOTE:
The information contained in this Instruction Manual is designed to assist you in the safe operation and
maintenance of the power tool.
NEVER operate, or attempt any maintenance on the tool unless you have first read and understood all safety
instructions contained in this manual.
Some illustrations in this Instruction Manual may show details or attachments that differ from those on your
own power tool.
Grip
Change lever
Side handle
Battery
Switch trigger
Shift knob
Push button
Front cap
Depth gauge
Battery
Latch
Terminals
Battery cover
Ventilation holes
01Eng_DH18DSL_US 2/14/13, 15:179
English
10
SPECIFICATIONS
1. Cordless Rotary Hammer (DH18DSL)
* Do not use the “SAVE” mode when boring holes with the wood drill. There is a likelihood that the motor will
burn out.
Motor DC motor
No-load speed SAVE/POWER 0 – 750/min. / 0 – 1,500/min.
Full-load impact rate SAVE/POWER 0 – 3,100/min. / 0 – 6,200/min.
Concrete 5/8″ (16 mm)
Capacity Drilling Steel 1/2″ (13 mm)
Wood 11/16″ (18 mm) *
Model BSL1830
Battery Type Lithium-ion battery
Voltage DC 18 V
Weight 4.8 lbs. (2.2 kg)
2. Battery Charger (UC18YRSL)
NOTE: The charging time may vary according to temperature and power source voltage.
Input power source Single phase: AC 120 V 60 Hz
Charging time Approx. 45 min.
Charging voltage DC 14.4 V – 18 V
Charger
Charging current DC 3.5 A
Weight 1.3 lbs. (0.6 kg)
2. Battery Charger (UC18YRSL)
Fig. 2
Pilot lamp
Cord
Nameplate
Guide rail
01Eng_DH18DSL_US 2/14/13, 15:1710
English
11
APPLICATIONS
Rotation and hammering function
䡬
Drilling anchor holes
䡬
Drilling holes in concrete
䡬
Drilling holes in tile
Rotation only function
䡬
Drilling in steel or wood
䡬
Tightening machine screws, wood screws
REMOVAL AND INSTALLATION METHOD
OF BATTERY
1. Battery removal
Hold the handle tightly and push the battery latch
to remove the battery (See Fig. 3).
CAUTION
Never short-circuit the battery.
2. Battery installation
Insert the battery while observing its polarities (See
Fig. 3).
CHARGING METHOD
NOTE:
Before plugging into the receptacle, make sure the
following points.
䡬
The power source voltage is stated on the
nameplate.
䡬
The cord is not damaged.
WARNING:
Do not charge at voltage higher than indicated on
the nameplate.
If charged at voltage higher than indicated on the
nameplate, the charger will burn up.
ASSEMBLY AND OPERATION
1. Connect the charger’s power cord to a receptacle.
When the power cord is connected, the charger’s
pilot lamp will blink in red. (At 1-second intervals)
WARNING:
Do not use the electrical cord if
damaged. Have it repaired
immediately.
2. Insert the battery into the charger.
Firmly insert the battery into the charger until the
line is visible, as shown in Fig. 4 .
3. Charging
When the battery is connected to the battery
charger, charging will commence and the pilot
lamp will light in red. (See Table 2)
NOTE:
If the pilot lamp flikers in red, pull out the plug
from the receptacle and check if the battery is
properly mounted.
When the battery is fully charged, the pilot lamp
will blink in red slowly. (At 1-second intervals) (See
Table 2)
Fig. 4
Fig. 3
Latch
Handle
Insert
Battery
Pull out
Push
Line
Battery
Charger
Pilot lamp
01Eng_DH18DSL_US 2/14/13, 15:1711
English
12
(1) Pilot lamp indication
The indications of the pilot lamp will be as shown
in Table 2, according to the condition of the charger
or the rechargeable battery.
(2) Regarding the temperature of the rechargeable
battery.
The temperatures for rechargeable batteries are
as shown in the Table 3, and batteries that have
become hot should be cooled for a while before
being recharged.
(3) Regarding recharging time (At 68°F (20°C))
Table 4 Charging time (At 20°C)
NOTE:
The charging time may vary according to
temperature and power source voltage.
4. Disconnect battery charger from the receptacle.
CAUTION
●
Do not pull the plug out of the receptacle by pulling
on the cord.
Make sure to grasp the plug when removing from
receptacle to avoid damaging cord.
Table 2
Indications of the pilot lamp
Lights for 0.5 seconds. Does not light for 0.5
seconds. (off for 0.5 seconds)
Lights continuously
Lights for 0.5 seconds. Does not light for 0.5
seconds. (off for 0.5 seconds)
Lights for 0.1 seconds. Does not light for 0.1
seconds. (off for 0.1 seconds)
Lights continuously
Before
charging
While
charging
Charging
complete
Charging
impossible
Blinks
Lights
Blinks
Flickers
Lights
Malfunction in the
battery or the charger
Battery overheated.
Unable to charge
(Charging will
commence when
battery cools).
Overheat
standby
The
pilot
lamp
lights or
blinks in
red.
The
pilot lamp
lights in
green.
5. Remove the battery from the battery charger.
Supporting the battery charger with hand, pull out
the battery from the battery charger.
How to make the batteries perform longer
(1) Recharge the batteries before they become
completely exhausted.
When you feel that the power of the tool becomes
weaker, stop using the tool and recharge its
battery. If you continue to use the tool and exhaust
the electric current, the battery may be damaged
and its life will become shorter.
(2) Avoid recharging at high temperatures.
A rechargeable battery will be hot immediately
after use. If such a battery is recharged immediately
after use, its internal chemical substance will
deteriorate, and the battery life will be shortened.
Leave the battery and recharge it after it has cooled
for a while.
CAUTION
●
When the battery charger has been continuosly
used, the battery charger will be heated, thus
constituting the cause of the failures. Once the
charging has been completed, give 15 minutes rest
until the next charging.
●
If the battery is rechraged when it is warm due to
battery use or exposure to sunlight, the pilot lamp
may light in green.
The battery will not be recharged. In such a case,
let the battery cool before charging.
Table 3 Recharging ranges of batteries
Rechargeable Temperatures at which the
batteries battery can be recharged
BSL1830
32°F–104°F
(0°C–40°C)
Charger
UC18YRSL
Battery
BSL1830 Approx. 45 min.
01Eng_DH18DSL_US 2/14/13, 15:1712
English
13
2. Confirm that the battery is mounted correctly.
3. Installation of dust cup or dust collector (B)
(Optional accessories) (Fig. 7, Fig. 8)
When using a rotary hammer for upward drilling
operations attach a dust cup or a dust collector (B)
to collect dust or particles for easy operation.
䡬
Installing the dust cup
Use the dust cup by attaching to the drill bit as
shown in Fig. 7.
When using a bit which has big diameter, enlarge
the center hole of the dust cup with this rotary
hammer.
䡬
Installing dust collector (B)
When using dust collector (B), insert dust collector
(B) from the tip of the bit by aligning it to the groove
on the grip. (Fig. 8)
CAUTION:
●
The dust cup and dust collector (B) are for
exclusive use of concrete drilling work. Do not use
them for wood or metal drilling work.
●
Insert dust collector (B) completely into the chuck
part of the main unit.
●
When turning the rotary hammer on while dust
collector (B) is detached from a concrete surface,
dust collector (B) will rotate together with the drill
bit. Make sure to turn on the switch after pressing
dust cup on the concrete surface. When using dust
●
When the pilot lamp flikers rapidly in red (at 0.2–
second intervals), check for and take out any
foreign objects in the charger’s battery installation
hole. If there are no foreign objects, it is probable
that the battery or charger is malfunctioning. Take
it to your authorized Service Center.
BEFORE USE
Check the work area to make sure that it is clear of debris
and clutter.
Clear the area of unnecessary personnel. Ensure that
lighting and ventilation is adequate.
PRIOR TO OPERATION
1. Mounting the drill bit (Fig. 5, 6)
CAUTION:
To prevent accidents, make sure to turn the switch
off.
NOTE:
When using tools such as drill bits, etc., make sure
to use the genuine parts designated by our company.
(1) Clean the shank portion of the drill bit.
(2) Insert the drill bit in a twisting manner into the tool
holder until it latches itself. (Fig. 5)
The grip need not be adjusted during bit installation.
(3) Check the latching by pulling on the drill bit.
(4) To remove the drill bit, fully pull the grip in the
direction of the arrow and pull out the drill bit.
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Dust cup
Dust
collector (B)
Front cap
Grip
Drill bit
Part of SDS-plus
shank
Drill bit
Part of SDS-plus
shank
Grip
01Eng_DH18DSL_US 2/14/13, 15:1713
English
14
collector (B) attached to a drill bit that has more
than 190 mm of overall length, dust collector (B)
cannot touch the concrete surface and will rotate.
Therefore, please use dust collector (B) by
attaching to drill bits which have 166 mm, 160 mm,
and 110 mm overall length.
●
Dump particles after every two or three holes
when drilling.
●
Please replace the drill bit after removing dust
collector (B).
4. Selecting the driver bit
Screw heads or bits will be damaged unless a bit
appropriate for the screw diameter is employed to
drive in the screws.
5. Confirm the direction of bit rotation (Fig. 9)
The bit rotates clockwise (viewed from the rear
side) by pushing the R-side of the push button.
The L-side of the push button is pushed to turn the
bit counterclockwise. (See Fig. 9) (The
L
and
R
marks are provided on the body.)
CAUTION:
The push button cannot be switched while the
power tool is turning. To switch the push button,
stop the power tool, then set the push button.
6. Continuous drilling
The number of holes that can be drilled in concrete
after one recharge is shown in Table 5.
Table 5
* Use an adapter for a small diameter bit.
Fig. 9
Bit dia. Depth Possible continuous
(mm) (mm) drilling number (holes)
*3.5 110
4 122
5 113
6 105
830 77
10 64
12 57
14 47
16 32
Fig. 10
Push button
L
marks
R
marks
L
R
L
R
These data are for the referential values. The number of
holes that can be drilled varies according to the sharpness
of the used bit or the conditions of the concrete being
drilled.
CAUTION:
When using this unit continuously, the unit may
overheat, leading to damage in the motor and
switch. Please leave it without using it for
approximately 15 minutes.
HOW TO USE
1. Switch operation
䡬
When the switch trigger is depressed, the tool
rotates. When the switch trigger is released, the tool
stops.
䡬
The rotational speed of the rotary hammer can be
controlled by varying the amount that the switch
trigger is pulled. Speed is low when the switch
trigger is pulled slightly and increases as the switch
trigger is pulled more.
䡬
When releasing the switch trigger, the brake will
be applied for immediate stopping.
2. Rotation + Hammering
Turn the change lever fully in the direction of the
“ ” mark to set “rotation + hammering”. (Fig.
10)
(1) Mount the drill bit.
(2) Pull the trigger switch after applying the drill bit
tip to the drilling position. (Fig. 11)
“ ” mark
Change
lever
“ ” mark
Fig. 11
01Eng_DH18DSL_US 2/14/13, 15:1714
English
15
(3) Pushing the rotary hammer forcibly is not necessary
at all. Pushing slightly so that drill dust comes out
gradually is just sufficient.
CAUTION:
When the drill bit touches construction iron bar,
the bit will stop immediately and the rotary
hammer will react to revolve. Therefore please grip
the side handle and handle tightly as shown in
Fig. 11.
3. Rotation only
Turn the change lever fully in the direction of the
“ ” mark to set “rotation only”. (Fig. 10)
To drill a wood or metal material using the optional
drill chuck and chuck adapter, proceed as follows.
Installing drill chuck and chuck adapter : (Fig. 12)
(1) Attach the drill chuck to the chuck adaptor.
(2) The part of the SDS-plus shank is the same as the
drill bit. Therefore, refer to the item of “Mounting
the drill bit” for attaching it.
CAUTION:
●
Application of force more than necessary will not
only expedite work at all, but will deteriorate the
tip edge of the drill bit and reduce the service life
of the rotary hammer in addition.
●
Drill bit may snap off while withdrawing the rotary
hammer from the drilled hole. For withdrawing,
it is important to use a pushing motion.
●
Do not attempt to use the rotary hammer in the
rotation and striking mode with the drill chuck and
chuck adapter attached. This would seriously
shorten the service life of every component of the
machine.
4. When driving wood screws (Fig. 13)
(1) Selecting a suitable driver bit
Employ plus-head screws, if possible, since the
driver bit easily slips off the heads of slotted-head
screws.
(2) Tightening wood screws
Prior to tightening wood screws, make pilot holes
suitable for them in the wooden board. Apply the
bit to the screw head grooves and gently drive the
screws in the holes.
CAUTION:
Exercise care in preparing a pilot hole suitable for
the wood screw taking the hardness of the wood
into consideration. Should the hole be excessively
small or shallow, requiring much power to drive
the screw into it, the thread of the wood screw
may sometimes be damaged.
5. Using depth gauge (Fig. 14)
(1) Loosen the knob on the side handle, and insert the
depth gauge into the mounting hole on the side
handle.
(2) Adjust the depth gauge position according to the
depth of the hole and tighten the knob bolt securely.
6. How to use the drill bit (taper shank) and the taper
shank adapter
(1) Mount the taper shank adapter to the rotary
hammer. (Fig. 15)
(2) Mount the drill bit (taper shank) to the taper shank
adapter. (Fig. 15)
(3) Turn the switch ON, and drill a hole to prescribed
depth.
(4) To remove the drill bit (taper shank), insert the
cotter into the slot of the taper shank adapter and
strike the head of the cotter with a hammer
supporting on the rest. (Fig. 16)
Fig. 13
Fig. 12
Grip
Drill chuck
Chuck adapter
Part of SDS-plus shank
Front
cap
Bit
Socket
Front cap
Chuck adapter
Grip
Fig. 14
Mounting hole
Depth gauge
Side handle
01Eng_DH18DSL_US 2/14/13, 15:1715
English
16
7. Switching between the “SAVE“ and the “POWER“
modes
The hammering force of the hammer can be
increased or decreased to conform with intended
usage, by operating the shift knob as per Fig. 17.
Adjust the force to match the usage intended.
(1) “SAVE“ mode ... decreased hammering force
This can prevent thin drill bits which are less than
4.3 mm in diameter, from being bent or broken.
(2) “POWER“ mode ... increased hammering force
䡬
This can be used to speedily and efficiently drill
holes when the drill bits which are being used are
greater than 4 mm in diameter.
䡬
This can be used to drill holes into wood or metal.
CAUTION:
Do not drill holes in wood with the “SAVE“ mode.
There is a likelihood that the motor will burn out
because it can easily lock up due to the low power.
8. About Remaining Battery Indicator
When pressing the remaining battery indicator
switch, the remaining battery indicator lamp lights
and the battery remaining power can be checked.
(Fig.18) When releasing your finger from the
remaining battery indicator switch, the remaining
battery indicator lamp goes off. The table 6 shows
the state of remaining battery indicator lamp and
the battery remaining power.
As the remaining battery indicator shows
somewhat differently depending on ambient
temperature and battery characteristics, read it as
a reference.
Fig. 18
Table 6
Fig. 16
Fig. 15
Drill bit
Taper shank
adapter
Grip
Front cap
Cotter
Rests
Taper shank
adapter
Fig. 17
Shift knob
“POWER“ mode
“SAVE“ mode
Remaining battery
indicator lamp
Remaining battery
indicator switch
State of lamp Battery Remaining Power
The battery remaining power
is enough.
The battery remaining power
is a half.
The battery remaining power
is nearly empty.
Re-charge the battery soonest
possible.
01Eng_DH18DSL_US 2/14/13, 15:1716
English
17
MAINTENANCE AND INSPECTION
CAUTION:
Pull out battery before doing any inspection or maintenance.
1. Inspecting the drill bits
Since use of a dull tool will cause motor
malfunctioning and degraded efficiency, replace
the drill bit with a new one or resharpening without
delay when abrasion is noted.
2. Check the Screws
Loose screws are dangerous. Regularly inspect
them and make sure they are tight.
CAUTION:
Using this power tool with loosened, screws is
extremely dangerous.
3. Maintenance of the motor
The motor unit winding is the very “heart” of the
power tool.
Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
4. Inspecting the carbon brushes (Fig. 20)
The motor employs carbon brushes which are
consumable parts. Since and excessively worn
carbon brush can result in motor trouble, replace
the carbon brush with new ones when it becomes
worn to or near the “wear limit”. In addition,
always keep carbon brushes clean and ensure that
they slide freely within the brush holders.
NOTE:
When replacing the carbon brush with a new one,
be sure to use the Hitachi Carbon Brush Code No.
328481.
Fig. 20
5. Replacing carbon brushes
Take out the carbon brush by first removing the
brush cap and then hooking the protrusion of the
carbon brush with a flat head screw driver, etc., as
shown in Fig. 21.
When installing the carbon brush, choose the
direction so that the nail of the carbon brush agrees
with the contact portion outside the brush tube.
Then push it in with a finger as illustrated in Fig.
23. Lastly, install the brush cap.
NOTE:
䡬
Do not give a strong shock to the switch panel or
break it.It may lead to a trouble.
䡬
To save the battery power consumption, the
remaining battery indicator lamp lights while
pressing the remaining battery indicator switch.
9. How to use the LED light
Every time you press the light switch on the switch
panel, the LED light lights or goes off. (Fig. 19)
To prevent the battery power consumption, turn
off the LED light frequently.
Fig. 19
CAUTION
䢇
Do not expose directly your eye to the light by
looking into the light.
If your eye is continuously exposed to the light,
your eye will be hurt.
NOTE:
䡬
To prevent the battery power consumption caused
by forgetting to turn off the LED light, the light goes
off automatically in about 15 minutes.
Light switch
Wear limit
0.12" (3 mm)
0.37" (9.5 mm)
01Eng_DH18DSL_US 2/14/13, 15:1717
English
18
CAUTION:
●
Be absolutely sure to insert the nail of the carbon
brush into the contact portion outside the brush
tube. (You can insert whichever one of the two
nails provided.)
●
Caution must be exercised since any error in this
operation can result in the deformed nail of the
carbon brush and may cause motor trouble at an
early stage.
Fig. 21
Fig. 22
Fig. 23
6. How to replace grease
Low viscosity grease is applied to this rotary
hammer so that it can be used for a long period
without replacing the grease. Please contact the
nearest service center for grease replacement
when any grease is leaking from loosened screw.
Further use of the rotary hammer despite the
grease shortage causes seizure to reduce the
service life.
CAUTION:
A specific grease is used with this machine,
therefore, the normal performance of the machine
may be badly affected by use of other grease.
Please be sure to let one of our service agents
undertake replacement of the grease.
7. Check for Dust
Dust may be removed with a soft cloth or a cloth
dampened with soapy water.
Do not use bleach, chlorine, gasoline or thinner,
for they may damage the plastics.
8. Disposal of the exhausted battery
WARNING:
Do not dispose of the exhausted battery. The
battery must explode if it is incinerated. The
product that you have purchased contains a
rechargeable battery. The battery is recyclable. At
the end of it’s useful life, under various state and
local laws, it may be illegal to dispose of this
battery into the municipal waste stream. Check
with your local solid waste officials for details in
your area for recycling options or proper disposal.
9. Storage
Storing in a place below 104°F (40°C) and out of
the reach of children.
NOTE:
Make sure that the battery is fully charged when
stored for a long period (3 months or more). The
battery with smaller capacity may not be able to
be charged when used, if stored for a long period.
10. Service and repairs
All quality power tools will eventually require
servicing or replacement of parts because of wear
from normal use. To assure that only authorized
replacement parts will be used, all service and
repairs must be performed by a HITACHI
AUTHORIZED SERVICE CENTER, ONLY.
11. Service parts list
A: Item No.
B: Code No.
C: No. Used
D: Remarks
CAUTION:
Repair, modification and inspection of Hitachi
Power Tools must be carried out by a Hitachi
Authorized Service Center.
This Parts List will be helpful if presented with the
tool to the Hitachi Authorized Service Center when
requesting repair or other maintenance. In the
operation and maintenance of power tools, the
safety regulations and standards prescribed in
each country must be observed.
Nail of carbon brush
Protrusion of
carbon brush
Contact portion
outside brush tube
01Eng_DH18DSL_US 2/14/13, 15:1718
English
19
ACCESSORIES
WARNING:
ALWAYS use Only authorized HITACHI replacement parts and accessories. NEVER use replacement parts or
accessories which are not intended for use with this tool. Contact HITACHI if you are not sure whether it is
safe to use a particular replacement part or accessory with your tool.
The use of any other attachment or accessory can be dangerous and could cause injury or mechanical
damage.
NOTE:
Accessories are subject to change without any obligation on the part of the HITACHI.
STANDARD ACCESSORIES
OPTIONAL ACCESSORIES.....sold separately
1. Battery (BSL1830)
BSL1830 (Code No. 330067)
MODIFICATIONS:
Hitachi Power Tools are constantly being improved
and modified to incorporate the latest
technological advancements.
Accordingly, some parts (i.e. code numbers and/
or design) may be changed without prior notice.
1
Side handle (Code No. 324548) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2
Depth gauge (Code No. 303709) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
DH18DSL
3
Charger (UC18YRSL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
(2LSCK)
4
Plastic case (Code No. 329894) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
5
Battery (BSL1830) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
6
Battery cover (Code No. 329897) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
DH18DSL (NN) Charger, plastic case, battery and battery cover are not contained.
Important notice on the batteries for the Hitachi
cordless power tools
Please always use one of our designated genuine
batteries. We cannot guarantee the safety and
performance of our cordless power tool when
used with batteries other than these designated
by us, or when the battery is disassembled and
modified (such as disassembly and replacement
of cells or other internal parts).
01Eng_DH18DSL_US 2/14/13, 15:1719
English
20
2. Tool and Adapter
Rotation + Hammering
Tool Adapters
Rotation only
+
Adapter for slender shaft
(SDS-plus shank)
Drill bit (Slender shaft)
䢇
Drilling holes in concrete or tile
Drill bit (Taper shank)
Taper shank
adapter
Cotter
䢇
Drilling holes in concrete
䢇Anchor setting
Anchor setting adapter
+ +
Chuck
adapter
Drill chuck
(13 VLRB-D)
Special
screw
䢇 Demolishing operation
Dust cup
Dust collector (B)
䢇
Drilling holes in concrete or tile
䢇 Drilling anchor holes
䢇 Driving screws
䢇 Drilling in steel or wood
, Driver bit - Driver bit
Drill bit for steel Drill bit for
wood
Bull point
(Round type)
Drill bit
Use on jobs facing upwards
( )
Straight shank bit for
impact drill
13 mm Rotary hammer chuck
(SDS-plus shank)
01Eng_DH18DSL_US 2/14/13, 15:1720
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
Hitachi DH 18DSL Manuel utilisateur
- Catégorie
- Outils électroportatifs
- Taper
- Manuel utilisateur
dans d''autres langues
- English: Hitachi DH 18DSL User manual
- español: Hitachi DH 18DSL Manual de usuario
Documents connexes
-
Hitachi DN 18DSL Manuel utilisateur
-
Hitachi DV18DSL Manuel utilisateur
-
-
-
-
-
Hitachi WH 18DBDL Manuel utilisateur
-
-
-