Hitachi WR 18DSHL Safety Instructions And Instruction Manual

Marque: Hitachi

Modèle: WR 18DSHL

Catégorie: Outils électroportatifs

Taper: Safety Instructions And Instruction Manual

INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI

AVERTISSEMENT

Une utilisation INCORRECTE OU DANGEREUSE de cet outil motorisé peut entraîner la

mort ou de sérieuses blessures corporelles !

Ce mode d’emploi contient d’importantes informations à propos de la sécurité de ce

produit. Prière de lire et de comprendre ce mode d’emploi AVANT d’utiliser l’outil

motorisé. Garder ce mode d’emploi à la disponibilité des autres utilisateurs et propriétaires

avant qu’ils utilisent l’outil motorisé. Ce mode d’emploi doit être conservé dans un

endroit sûr.

SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL

WARNING

IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily

injury!

This manual contains important information about product safety. Please read and

understand this manual BEFORE operating the power tool. Please keep this manual

available for other users and owners before they use the power tool. This manual should

be stored in safe place.

INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES

ADVERTENCIA

¡La utilización INAPROPIADA O PELIGROSA de esta herramienta eléctrica puede

resultar en lesiones de gravedad o la muerte!

Este manual contiene información importante sobre la seguridad del producto. Lea y

comprenda este manual ANTES de utilizar la herramienta eléctrica. Guarde este manual

para que puedan leerlo otras personas antes de utilizar la herramienta eléctrica. Este

manual debe ser guardado en un lugar seguro.

Model Cordless Impact Wrench

Modèle Clé à choc sans fil

Modelo Llave de impacto a batería

WR 18DSHL

Designed for operating in USA & Canada only.

When this product is used in areas other than the USA & Canada,

we cannot guarantee the product quality and performance.

01Eng_WR18DSHL_US.p65 8/28/13, 14:491

CONTENTS

Page

IMPORTANT SAFETY INSTRUCTIONS ............... 3

MEANINGS OF SIGNAL WORDS ........................ 3

SAFETY ...................................................................... 3

GENERAL POWER TOOL SAFETY WARNINGS ... 3

SPECIFIC SAFETY RULES AND SYMBOLS ......... 5

IMPORTANT SAFETY INSTRUCTIONS FOR

USE OF THE CORDLESS IMPACT WRENCH ..

IMPORTANT SAFETY INSTRUCTIONS

FOR BATTERY CHARGER ............................. 6

IMPORTANT SAFETY INSTRUCTIONS

FOR USE OF THE BATTERY AND

BATTERY CHARGER ...................................... 7

CAUTION ON LITHIUM-ION BATTERY ............... 7

FUNCTIONAL DESCRIPTION .................................... 9

NAME OF PARTS .................................................. 9

SPECIFICATIONS ................................................ 10

TABLE DES MATIERES

ÍNDICE

Página

DESCRIPCIÓN FUNCIONAL .................................... 45

NOMENCLATURA ............................................... 45

ESPECIFICACIONES ............................................ 46

MONTAJE Y OPERACIÓN ...................................... 47

APLICACIONES ................................................... 47

MÉTODO DE EXTRACCIÓN E INSTALACIÓN

DE LA BATERÍA ............................................ 47

MÉTODO DE CARGA .......................................... 47

ANTES DE LA UTILIZACIÓN .............................. 49

OPERACIÓN ........................................................ 49

PRECAUCIONES OPERACIONALES .................. 51

MANTENIMIENTO E INSPECCIÓN ........................ 52

ACCESORIOS ........................................................... 54

ACCESORIOS ESTÁNDAR ................................. 54

ACCESORIOS OPCIONALES...de venta por separado ...

LISTA DE PIEZAS .................................................... 56

Page

ASSEMBLY AND OPERATION ............................... 11

APPLICATIONS ................................................... 11

REMOVAL AND INSTALLATION METHOD

OF BATTERY ................................................ 11

CHARGING METHOD ......................................... 11

BEFORE USE ....................................................... 13

OPERATION ......................................................... 13

OPERATIONAL CAUTIONS ................................ 14

MAINTENANCE AND INSPECTION ....................... 16

ACCESSORIES ......................................................... 18

STANDARD ACCESSORIES ............................... 18

OPTIONAL ACCESSORIES...sold separately .... 18

PARTS LIST .............................................................. 56

Page

CONSIGNES DE SÉCURITÉ IMPORTANTES

.......... 20

SIGNIFICATION DES MOTS D’AVERTISSEMENT

.... 20

SECURITE ................................................................ 20

AVERTISSEMENTS DE SÉCURITÉ GÉNÉRAUX

CONCERNANT LES OUTILS ÉLECTRIQUES ........

REGLES DE SECURITE SPECIFIQUES ET SYMBOLES ....

CONSIGNES DE SÉCURITÉ IMPORTANTES POUR

L'UTILISATION DE LA CLÉ À CHOC SANS FIL ......

CONSIGNES DE SÉCURITÉ IMPORTANTES

POUR LE CHARGEUR DE BATTERIE ........... 23

CONSIGNES DE SÉCURITÉ IMPORTANTES

POUR L’UTILISATION DE LA BATTERIE ET

DU CHARGEUR DE BATTERIE .................... 24

PRÉCAUTIONS RELATIVES A LA BATTERIE AU

LITHIUM ION ................................................ 25

Page

DESCRIPTION FONCTIONNELLE ........................... 27

NOM DES PARTIES ............................................ 27

SPECIFICATIONS ................................................ 28

ASSEMBLAGE ET FONCTIONNEMENT ................ 29

UTILISATIONS .................................................... 29

MÉTHODE DE RETRAIT ET D’INSTALLATION

DE LA BATTERIE .......................................... 29

MÉTHODE DE RECHARGE ................................. 29

AVANT L’UTILISATION ...................................... 31

UTILISATION ....................................................... 31

PRECAUTIONS D'UTILISATION ........................ 33

ENTRETIEN ET INSPECTION .................................. 34

ACCESOIRES ........................................................... 36

ACCESSOIRES STANDARD ............................... 36

ACCESSOIRES EN OPTION...vendus séparément ...

LISTE DES PIECES ................................................... 56

Français

Español

Página

INSTRUCCIONES IMPORTANTES SOBRE

SEGURIDAD ................................................. 38

SIGNIFICADO DE LAS PALABRAS DE

SEÑALIZACIÓN ............................................ 38

SEGURIDAD ............................................................. 38

ADVERTENCIAS DE SEGURIDAD GENERAL DE LA

HERRAMIENTA ELÉCTRICA ..................................

NORMAS ESPECÍFICOS DE SEGURIDAD ......... 40

INSTRUCCIONES IMPORTANTES PARA LA UTILIZACIÓN

DEL LLAVE DE IMPACTO A BATERÍA ....................

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

PARA EL CARGADOR DE BATERÍAS

............ 41

INSTRUCCIONES IMPORTANTES DE SEGURIDAD PARA

LA BATERÍA Y EL CARGADOR DE BATERÍAS .....

ADVERTENCIA DE LA BATERÍA DE LITIO.....................

English

01Eng_WR18DSHL_US.p65 8/28/13, 14:492

English

IMPORTANT SAFETY INSTRUCTIONS

Read and understand all of the safety precautions, warnings and operating instructions in the Instruction Manual

before operating or maintaining this power tool.

Most accidents that result from power tool operation and maintenance are caused by the failure to observe basic

safety rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation

before it occurs, and by observing appropriate safety procedures.

Basic safety precautions are outlined in the “SAFETY” section of this Instruction Manual and in the sections which

contain the operation and maintenance instructions.

Hazards that must be avoided to prevent bodily injury or machine damage are identified by WARNINGS on the

power tool and in this Instruction Manual.

NEVER use this power tool in a manner that has not been specifically recommended by HITACHI.

MEANINGS OF SIGNAL WORDS

WARNING indicates a potentially hazardous situations which, if ignored, could result in death or serious injury.

CAUTION indicates a potentially hazardous situations which, if not avoided, may result in minor or moderate

injury, or may cause machine damage.

NOTE emphasizes essential information.

SAFETY

GENERAL POWER TOOL SAFETY WARNINGS

WARNING:

Read all safety warnings and all instructions.

Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated

(cordless) power tool.

1) Work area safety

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust.

Power tools create sparks which may ignite

the dust or fumes.

c) Keep children and bystanders away while

operating a power tool.

Distractions can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet.

Never modify the plug in any way.

Do not use any adapter plugs with earthed

(grounded) power tools.

Unmodified plugs and matching outlets will

reduce risk of electric shock.

b) Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators.

There is an increased risk of electric shock if

your body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions.

Water entering a power tool will increase the

risk of electric shock.

d) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges

or moving parts.

Damaged or entangled cords increase the risk

of electric shock.

e) When operating a power tool outdoors, use

an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces

the risk of electric shock.

f) If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply.

Use of an RCD reduces the risk of electric shock.

3) Personal safety

a) Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired

or under the influence of drugs, alcohol or

medication.

01Eng_WR18DSHL_US.p65 8/28/13, 14:493

English

A moment of inattention while operating

power tools may result in serious personal

injury.

b) Use personal protective equipment. Always

wear eye protection.

Protective equipment such as dust mask, non-

skid safety shoes, hard hat, or hearing

protection used for appropriate conditions

will reduce personal injuries.

c) Prevent unintentional starting. Ensure the

switch is in the off-position before connecting

to power source and/or battery pack, picking

up or carrying the tool.

Carrying power tools with your finger on the

switch or energising power tools that have

the switch on invites accidents.

d) Remove any adjusting key or wrench before

turning the power tool on.

A wrench or a key left attached to a rotating

part of the power tool may result in personal

injury.

e) Do not overreach. Keep proper footing and

balance at all times.

This enables better control of the power tool

in unexpected situations.

f) Dress properly. Do not wear loose clothing

or jewellery. Keep your hair, clothing and

gloves away from moving parts.

Loose clothes, jewellery or long hair can be

caught in moving parts.

g) If devices are provided for the connection of

dust extraction and collection facilities,

ensure these are connected and properly

used.

Use of dust collection can reduce dust-related

hazards.

4) Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application.

The correct power tool will do the job better

and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does

not turn it on and off.

Any power tool that cannot be controlled with

the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools.

Such preventive safety measures reduce the

risk of starting the power tool accidentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool.

Power tools are dangerous in the hands of

untrained users.

e) Maintain power tools. Check for

misalignment or binding of moving parts,

breakage of parts and any other condition

that may affect the power tool’s operation.

If damaged, have the power tool repaired

before use.

Many accidents are caused by poorly

maintained power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are

easier to control.

g) Use the power tool, accessories and tool bits

etc. in accordance with these instructions,

taking into account the working conditions

and the work to be performed.

Use of the power tool for operations different

from those intended could result in a

hazardous situation.

5) Battery tool use and care

a) Recharge only with the charger specified by

the manufacturer.

A charger that is suitable for one type of

battery pack may create a risk of fire when

used with another battery pack.

b) Use power tools only with specifically

designated battery packs.

Use of any other battery packs may create a

risk of injury and fire.

c) When battery pack is not in use, keep it away

from other metal objects like paper clips,

coins, keys, nails, screws, or other small

metal objects, that can make a connection

from one terminal to another.

Shorting the battery terminals together may

cause burns or a fire.

d) Under abusive conditions, liquid may be

ejected from the battery; avoid contact. If

contact accidentally occurs, flush with water.

If liquid contacts eyes, additionally seek

medical help. Liquid ejected from the battery

may cause irritation or burns.

6) Service

a) Have your power tool serviced by a qualified

repair person using only identical

replacement parts.

This will ensure that the safety of the power

tool is maintained.

–WARNING–

To reduce the risk of injury, user must read

instruction manual.

01Eng_WR18DSHL_US.p65 8/28/13, 14:494

English

WARNING:

Some dust created by power sanding, sawing,

grinding, drilling, and other construction activities

contains chemicals known [to the State of California]

to cause cancer, birth defects or other reproductive

harm. Some examples of these chemicals are:

●

Lead from lead-based paints,

●

Crystalline silica from bricks and cement and other

masonry products, and

●

Arsenic and chromium from chemically-treated

lumber.

Your risk from these exposures varies, depending

on how often you do this type of work. To reduce

your exposure to these chemicals: work in a well

ventilated area, and work with approved safety

equipment, such as those dust masks that are

specially designed to filter out microscopic particles.

SPECIFIC SAFETY RULES AND SYMBOLS

1. Hold power tool by insulated gripping surfaces,

when performing an operation where the fastener

may contact hidden wiring. Fasteners contacting

a "live" wire may make exposed metal parts of the

power tool "live" and could give the operator an

electric shock.

2. ALWAYS wear ear protectors when using the tool

for extended periods.

Prolonged exposure to high intensity

noise can cause hearing loss.

3. NEVER place hands or other body parts near the

drill bit or chuck during operation. Hold the drill by

its handle only.

4. Because the cordless driver drill operates by battery

power, be aware of the fact that it can begin to

operate at any time.

5. When working at elevated locations, clear the area

of all other people and be aware of conditions

below you.

6. NEVER touch moving parts.

NEVER place your hands, fingers or other body

parts near the tool’s moving parts.

7. NEVER operate without all guards in place.

NEVER operate this tool without all guards or

safety features in place and in proper working

order. If maintenance or servicing requires the

removal of a guard or safety feature, be sure to

replace the guard or safety feature before resuming

operation of the tool.

8. Use right tool.

Don’t force small tool or attachment to do the job

of a heavy-duty tool.

Don’t use tool for purpose not intended —for

example— don’t use circular saw for cutting tree

limbs or logs.

9. NEVER use a power tool for applications other

than those specified.

NEVER use a power tool for applications other than

those specified in the Instruction Manual.

10. Handle tool correctly.

Operate the tool according to the instructions

provided herein. Do not drop or throw the tool.

NEVER allow the tool to be operated by children,

individuals unfamiliar with its operation or

unauthorized personnel.

11. Keep all screws, bolts and covers tightly in place.

Keep all screws, bolts, and plates tightly mounted.

Check their condition periodically.

12. Do not use power tools if the plastic housing or

handle is cracked.

Cracks in the tool’s housing or handle can lead to

electric shock. Such tools should not be used until

repaired.

13. Blades and accessories must be securely mounted

to the tool.

Prevent potential injuries to yourself or others.

Blades, cutting implements and accessories which

have been mounted to the tool should be secure

and tight.

14. NEVER use a tool which is defective or operating

abnormally.

If the tool appears to be operating unusually,

making strange noises, or otherwise appears

defective, stop using it immediately and arrange

for repairs by a Hitachi authorized service center.

15. Carefully handle power tools.

Should a power tool be dropped or struck against

hard materials inadvertently, it may be deformed,

cracked, or damaged.

16. Do not wipe plastic parts with solvent.

Solvents such as gasoline, thinner benzine, carbon

tetrachloride, and alcohol may damage and crack

plastic parts. Do not wipe them with such solvents.

Wipe plastic parts with a soft cloth lightly

dampened with soapy water and dry thoroughly.

17. ALWAYS wear eye protection that meets the

requirement of the latest revision of

ANSI Standard Z87.1.

18. Definitions for symbols used on this tool

V ............... volts

—

---

.............. direct current

no ............ no load speed

---/min ...... revolutions or reciprocation per minute

01Eng_WR18DSHL_US.p65 8/28/13, 14:495

English

IMPORTANT SAFETY INSTRUCTIONS FOR

USE OF THE CORDLESS IMPACT WRENCH

WARNING:

Death or serious bodily injury could result from

improper or unsafe use of the cordless impact

wrench. To avoid these risks, follow these basic

safety instructions:

1. Never use this wrench handle for any application

other than those in this manual.

2. When working in high places, always make sure

that there is no one below before starting to work.

3. Always wear eye and ear protection when you work.

4. Confirm whether the socket has any crack in it.

5. Attach the hex. socket securely onto the anvil. If

the hex. socket is insufficiently secured, it may drop

out and cause an accident. For hex. socket

attachment refer to “OPERATION”.

6. Confirm the tightening torque by a torque wrench

before use in order to ascertain the correct

tightening torque to be used.

7. If a universal joint is used, be sure not to operate

the unit in a no-load condition. Operating in this

condition is dangerous. When the socket section

spins around it may cause injury to hands or

bodies, or the resulting intense vibration may

cause the user to drop the tool.

8. Be careful that foreign matters do not block the

holes located on both sides of the handle. Also do

not close the holes with a tape. The holes act an

important role.

IMPORTANT SAFETY INSTRUCTIONS FOR

BATTERY CHARGER

WARNING:

Death or serious bodily injury could result from

improper or unsafe use of battery chargers. To

avoid these risks, follow these basic safety

instructions:

READ ALL INSTRUCTIONS

1. This manual contains important safety and

operating instructions for battery charger Model

UC18YRSL/UC18YFSL.

2. Before using battery charger, read all instructions

and cautionary markings on (1) battery charger,

(2) battery, and (3) product using battery.

3. To reduce risk of injury, charge HITACHI

rechargeable battery type BSL18 series. Other type

of batteries may burst causing personal injury and

damage.

4. Do not expose battery charger to rain or snow.

5. Use of an attachment not recommended or sold

by the battery charger manufacturer may result in

a risk of fire, electric shock, or injury to persons.

6. To reduce risk of damage to electric plug and cord,

pull by plug when disconnecting battery charger.

7. Make sure cord is located so that it will not be

stepped on, tripped over, or otherwise subjected

to damage or stress.

8. An extension cord should not be used unless

absolutely necessary. Use of improper extension

cord could result in a risk of fire and electric shock.

If extension cord must be used make sure:

a. That blades of extension cord are the same

number, size, and shape as those of plug on

battery charger:

b. That extension cord is properly wired and in

good electrical condition; and

c. That wire size is large enough for AC ampere

rating of battery charger as specified in

Table 1.

Table 1

RECOMMENDED MINIMUM AWG SIZE FOR

EXTENSION CORDS FOR BATTERY CHARGERS

AC Input Rating Amperes* AWG Size of Cord

Equal to or but less Length of Cord, Feet (Meter)

greater than than 25 (7.5) 50 (15) 100 (30) 150 (45)

0 2 18 18 18 16

2 3 18 18 16 14

3 4 18 18 16 14

01Eng_WR18DSHL_US.p65 8/28/13, 14:496

English

* If the input rating of a battery charger is given in

watts rather than in amperes, the corresponding

ampere rating is to be determined by dividing the

wattage rating by the voltage rating–for example:

1,250 watts

125 volts

= 10 amperes

9. Do not operate battery charger with damaged cord

or plug-replace them immediately.

10. Do not operate battery charger if it has received a

sharp blow, been dropped, or otherwise damaged

in any way; take it to a qualified serviceman.

11. Do not disassemble battery charger; take it to a

qualified serviceman when service or repair is

required. Incorrect reassembly may result in a risk

of electric shock or fire.

12. To reduce risk of electric shock, unplug charger

from receptacle before attempting any

maintenance or cleaning. Removing the battery

will not reduce this risk.

IMPORTANT SAFETY INSTRUCTIONS FOR

USE OF THE BATTERY AND BATTERY

CHARGER

You must charge the battery before you can use the

power tool. Before using the model UC18YRSL/

UC18YFSL battery charger, be sure to read all

instructions and cautionary statements on it, the battery

and in this manual.

CAUTION:

USE ONLY HITACHI BATTERY TYPE BSL18

SERIES. OTHER TYPES OF BATTERIES MAY

BURST AND CAUSE INJURY!

Follow these instructions to avoid the risk of injury:

WARNING:

Improper use of the battery or battery charger can

lead to serious injury. To avoid these injuries:

1. NEVER disassemble the battery.

2. NEVER incinerate the battery, even if it is

damaged or is completely worn out. The battery

can explode in a fire.

3. NEVER short-circuit the battery.

4. NEVER insert any objects into the battery

charger’s air vents. Electric shock or damage to

the battery charger may result.

5. NEVER charge outdoors. Keep the battery away

from direct sunlight and use only where there is

low humidity and good ventilation.

6. NEVER charge when the temperature is below

32°F (0°C) or above 104°F (40°C).

Charging the battery at temperatures outside the

range of 32°F – 104°F (0°C – 40°C) may prevent

proper charging and reduce battery life.

7. NEVER connect two battery chargers together.

8. NEVER insert foreign objects into the hole for the

battery or the battery charger.

9. NEVER use a booster transformer when charging.

10. NEVER use an engine generator or DC power to

charge.

11. NEVER store the battery or battery charger in

places where the temperature may reach or exceed

104°F (40°C).

12.

ALWAYS

operate charger on standard household

electrical power (120 volts). Using the charger on

any other voltage may overheat and damage the

charger.

13.

ALWAYS

wait at least 15 minutes between charges

to avoid overheating the charger.

14.

ALWAYS

disconnect the power cord from its

receptacle when the charger is not in use.

CAUTION ON LITHIUM-ION BATTERY

To extend the lifetime, the lithium-ion battery equips

with the protection function to stop the output.

In the cases of 1 to 3 described below, when using this

product, even if you are pulling the switch, the motor

may stop. This is not the trouble but the result of

protection function.

1. When the battery power remaining runs out, the

motor stops.

In such case, charge it up immediately.

2. If the tool is overloaded, the motor may stop. In

this case, release the switch of tool and eliminate

causes of overloading. After that, you can use it

again.

3. If the battery is overheated under overload work,

the battery power may stop.

In this case, stop using the battery and let the

battery cool. After that, you can use it again.

Furthermore, please heed the following warning and

caution.

WARNING

In order to prevent any battery leakage, heat generation,

smoke emission, explosion and ignition beforehand,

please be sure to heed the following precautions.

1. Make sure that swarf and dust do not collect on

the battery.

䡬

During work make sure that swarf and dust do not

fall on the battery.

䡬

Make sure that any swarf and dust falling on the

power tool during work do not collect on the

battery.

䡬

Do not store an unused battery in a location

exposed to swarf and dust.

䡬

Before storing a battery, remove any swarf and

dust that may adhere to it and do not store it

together with metal parts (screws, nails, etc.).

2. Do not pierce battery with a sharp object such as a

nail, strike with a hammer, step on, throw or

subject the battery to severe physical shock.

3. Do not use an apparently damaged or deformed

battery.

4. Do not use the battery in reverse polarity.

01Eng_WR18DSHL_US.p65 8/28/13, 14:497

English

5. Do not connect directly to an electrical outlets or

car cigarette lighter sockets.

6. Do not use the battery for a purpose other than

those specified.

7. If the battery charging fails to complete even when

a specified recharging time has elapsed,

immediately stop further recharging.

8. Do not put or subject the battery to high

temperatures or high pressure such as into a

microwave oven, dryer, or high pressure container.

9. Keep away from fire immediately when leakage

or foul odor are detected.

10. Do not use in a location where strong static

electricity generates.

11. If there is battery leakage, foul odor, heat

generated, discolored or deformed, or in any way

appears abnormal during use, recharging or

storage, immediately remove it from the

equipment or battery charger, and stop use.

CAUTION

1. If liquid leaking from the battery gets into your

eyes, do not rub your eyes and wash them well

with fresh clean water such as tap water and

contact a doctor immediately.

If left untreated, the liquid may cause eye-

problems.

2. If liquid leaks onto your skin or clothes, wash well

with clean water such as tap water immediately.

There is a possibility that this can cause skin

irritation.

3. If you find rust, foul odor, overheating, discolor,

deformation, and/or other irregularities when using

the battery for the first time, do not use and return

it to your supplier or vendor.

WARNING

If an electrically conductive foreign object enters the

terminals of the lithium ion battery, a short-circuit may

occur resulting in the risk of fire. Please observe the

following matters when storing the battery.

䡬

Do not place electrically conductive cuttings, nails,

steel wire, copper wire or other wire in the storage

case.

䡬

Either install the battery in the power tool or store

by securely pressing into the battery cover until

the ventilation holes are concealed to prevent

short-circuits (See Fig. 1).

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO OTHER USERS

AND

OWNERS OF THIS TOOL!

01Eng_WR18DSHL_US.p65 8/28/13, 14:498

English

Fig. 1

1/2" (12.7 mm)

Ventilation holes

Latch

Battery cover

Battery

Terminals

Hammer case

Switch

Handle

Front cap

Battery

Anvil

Light

Housing

FUNCTIONAL DESCRIPTION

NOTE:

The information contained in this Instruction Manual is designed to assist you in the safe operation and

maintenance of the power tool.

NEVER operate, or attempt any maintenance on the tool unless you have first read and understood all safety

instructions contained in this manual.

Some illustrations in this Instruction Manual may show details or attachments that differ from those on your

own power tool.

NAME OF PARTS

1. Cordless Impact Wrench

䡬

Battery (BSL1830, BSL1840)

01Eng_WR18DSHL_US.p65 8/28/13, 14:499

English

2. Battery Charger

SPECIFICATIONS

Fig. 2

Pilot lamp

Cord

Nameplate

Model WR18DSHL

Motor DC motor

No-load speed 1,500 /min

Capacity

Ordinary bolt 15/32" – 7/8" (M12 – M22)

High tension bolt 15/32" – 5/8" (M12 – M16)

Maximum 354 ft-lbs. {480 N·m}

Tightening torque Tightening is 7/8" (M22) F10T, when fully charged at 68°F (20°C) temp.

Tightening time: 10 sec.

Drive 1/2" (12.7 mm) square

Rechargeable battery

BSL1830: Li-ion 18 V (3.0 Ah)

BSL1840: Li-ion 18 V (4.0 Ah)

Weight 7.5 lbs. (3.4 kg)

Model UC18YRSL UC18YFSL

Input power source Single phase: AC 120 V 60 Hz

Charging time

BSL1830: Approx. 45 min.

BSL1840: Approx. 60 min.

Charging voltage DC 14.4 V 18 V

Charger

Charging current

DC 14.4 V: DC 3.5 A

DC 18 V: DC 3.5 A

Weight 1.3 lbs. (0.6 kg) 1.1 lbs. (0.5 kg)

Battery Charger

Guide rail

Cord

Pilot lamp

Nameplate

Guide rail

01Eng_WR18DSHL_US.p65 8/28/13, 14:4910

English

ASSEMBLY AND OPERATION

APPLICATIONS

䡬

Tightening and loosening of all types of bolts and

nuts, used for securing structural

items.

REMOVAL AND INSTALLATION METHOD

OF BATTERY

1. Battery removal

Hold the handle tightly and push the battery latch to

remove the battery (see Fig. 3).

CAUTION

Never short-circuit the battery.

2. Battery installation

Insert the battery while observing its polarities (see

Fig. 3).

Fig. 3

CHARGING METHOD

NOTE:

Before plugging into the receptacle, make sure the

following points.

䡬

The power source voltage is stated on the

nameplate.

䡬

The cord is not damaged.

WARNING:

Do not charge at voltage higher than indicated on

the nameplate.

If charged at voltage higher than indicated on the

nameplate, the charger will burn up.

1. Connect the charger’s power cord to a receptacle.

When the power cord is connected, the charger’s

pilot lamp will blink in red. (At 1-second intervals)

WARNING:

Do not use the electrical cord if

damaged. Have it repaired

immediately.

2. Insert the battery to the battery charger.

Insert the battery into the battery charger as shown

in Fig. 4, 5.

Fig. 4

Fig. 5

Handle

Latch

Battery

Pull out

Push

Insert

Battery

Charger

Pilot lamp

Battery

Charger

Pilot lamp

01Eng_WR18DSHL_US.p65 8/28/13, 14:4911

English

3. Charging

When the battery is connected to the battery charger,

charging will commence and the pilot lamp will light

in red. (See Table 2)

NOTE:

If the pilot lamp flickers in red, pull out the plug from

the receptacle and check if the battery is properly

mounted.

(2) Regarding the temperature of the rechargeable

battery.

The temperatures for rechargeable batteries are as

shown in the Table 3, and batteries that have become

hot should be cooled for a while before being

recharged.

(3) Regarding recharging time

Table 4 Charging time (At 68°F (20°C))

NOTE:

The charging time may vary according to

temperature and power source voltage.

Table 3 Recharging ranges of batteries

Rechargeable Temperatures at which the

batteries battery can be recharged

BSL1830, 32°F – 122°F

BSL1840 (0°C – 50°C)

Charger

UC18YRSL / UC18YFSL

Battery

BSL1830 Approx. 45 min.

BSL1840 Approx. 60 min.

4. Disconnect battery charger from the receptacle.

CAUTION

Do not pull the plug out of the receptacle by pulling

on the cord.

Make sure to grasp the plug when removing from

receptacle to avoid damaging cord.

5. Remove the battery from the battery charger.

Supporting the battery charger with hand, pull out

the battery from the battery charger.

How to make the batteries perform longer

(1) Recharge the batteries before they become

completely exhausted.

When you feel that the power of the tool becomes

weaker, stop using the tool and recharge its battery.

If you continue to use the tool and exhaust the

electric current, the battery may be damaged and

its life will become shorter.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after

use. If such a battery is recharged immediately after

use, its internal chemical substance will deteriorate,

and the battery life will be shortened. Leave the

battery and recharge it after it has cooled for a while.

When the battery is fully charged, the pilot lamp will

blink in red slowly. (At 1-second intervals) (See Table

(1) Pilot lamp indication

The indications of the pilot lamp will be as shown in

Table 2, according to the condition of the charger or

the rechargeable battery.

Table 2

Indications of the pilot lamp

Lights for 0.5 seconds. Does not light for 0.5

seconds. (off for 0.5 seconds)

Lights continuously

Lights for 0.5 seconds. Does not light for 0.5

seconds. (off for 0.5 seconds)

Lights for 0.1 seconds. Does not light for 0.1

seconds. (off for 0.1 seconds)

Lights continuously

Lights for 1 secods. Does not light for 0.5

seconds. (off for 0.5 seconds)

Before

charging

While

charging

Charging

complete

Charging

impossible

Blinks

(red)

Lights

(red)

Blinks

(red)

Flickers

(red)

Lights

(green)

Blinks

(red)

Malfunction in the

battery or the charger

Battery overheated.

Unable to charge

(Charging will

commence when

battery cools).

Overheat

standby

The

pilot

lamp

lights or

blinks.

01Eng_WR18DSHL_US.p65 8/28/13, 14:4912

English

Fig. 7-1

3. Retaining ring type (Fig. 6, 7-2)

(1) Align the square portions of the socket and the anvil

with each other.

(2) Make sure to firmly install the socket by pushing it

all the way into the anvil.

(3) When removing the socket, pull it out of the anvil.

Fig. 7-2

CAUTION

䢇

Please use the designated attachments which are

listed in the operations manual and Hitachi’s

catalog. Accidents or injuries could result from

not doing so.

䢇

Make sure to firmly install the socket in the anvil.

If the socket is not firmly installed it might come

out and cause injuries.

4. Confirm that the battery is mounted correctly

5. Switch operation

The switch in this machine functions as a motor

switch and rotational direction selector switch. When

the switch is set to

indicated on the handle, the

motor rotates clockwise to tighten the bolt. When

the switch is set to

, the motor rotates

counterclockwise to loosen the bolt. When the switch

is released, the motor stops. (Fig. 8)

CAUTION

Be sure to turn the switch OFF and wait until the

motor completely stops before changing the

direction of wrench revolution. Switching while

the motor is rotating will result in burning the

motor.

CAUTION

●

When the battery charger has been continuosly

used, the battery charger will be heated, thus

constituting the cause of the failures. Once the

charging has been completed, give 15 minutes rest

until the next charging.

●

If the battery is rechraged when it is warm due to

battery use or exposure to sunlight, the pilot lamp

may light in green.

The battery will not be recharged. In such a case,

let the battery cool before charging.

●

When the pilot lamp flickers rapidly in red (at 0.2–

second intervals), check for and take out any

foreign objects in the charger’s battery installation

hole. If there are no foreign objects, it is probable

that the battery or charger is malfunctioning. Take

it to your authorized Service Center.

BEFORE USE

Check the work area to make sure that it is clear of debris

and clutter.

Clear the area of unnecessary personnel. Ensure that

lighting and ventilation is adequate.

OPERATION

1. Selecting the socket matched to the bolt

Be sure to use a socket which is matched to the bolt

to be tightened. Using an improper socket will not

only result in insufficient tightening but also in

damage to the socket or nut.

A worn or deformed hex. or square-holed socket will

not give an adequate tightness for fitting to the nut

or anvil, consequently resulting in loss of tightening

torque.

Pay attention to wear of socket hole, and replace

before further wear has developed.

Matching socket and bolt sizes are shown Tables 6.

The numerical value of a socket designation denotes

the side-to-side distance (H) of its hex. hole.

2. Installing a socket (Fig. 6, 7-1)

Align the plunger located in the square part of the

anvil with the hole in the hex. socket. Then push the

plunger, and mount the hex. socket on the anvil.

Check that the plunger is fully engaged in the hole.

When removing the socket, reverse the sequence.

Fig. 6

Hexagonal socket

Groove

Anvil

Plunger

Anvil

Hole

Hexagonal socket

Hole

Anvil

01Eng_WR18DSHL_US.p65 8/28/13, 14:4913

English

Fig. 9

NOTE:

䡬

Do not give a strong shock to the switch panel or

break it.It may lead to a trouble.

䡬

To save the battery power consumption, the

remaining battery indicator lamp lights while

pressing the remaining battery indicator switch.

8. How to use the LED light

Every time you press the light switch on the switch

panel, the LED light lights or goes off. (Fig. 10)

To prevent the battery power consumption, turn off

the LED light frequently.

Fig. 10

CAUTION

Do not expose directly your eye to the light by

looking into the light.

If your eye is continuously exposed to the light,

your eye will be hurt.

NOTE:

To prevent the battery power consumption caused

by forgetting to turn off the LED light, the light goes

off automatically in about 15 minutes.

OPERATIONAL CAUTIONS

1. Resting the unit after continuous work

After use for continuous bolt-tightening work, rest

the unit for 15 minutes or so when replacing the

battery. The temperature of the motor, switch, etc.

will rise if the work is started again immediately after

battery replacement, eventually resulting in burnout.

Fig. 8

6. Tightening and loosening bolts

A hex. socket matching the bolt or nut must first be

selected. Then mount the socket on the anvil, and

grip the nut to be tightened with the hex. socket.

Holding the wrench in line with the bolt, press the

power switch to impact the nut for several seconds.

If the nut is only loosely fitted to the bolt, the bolt

may turn with the nut, therefore mistaking proper

tightening. In this case, stop impact on the nut and

hold the bolt head with a wrench before restarting

impact, or manually tighten the bolt and nut to

prevent them slipping.

7. About Remaining Battery Indicator

When pressing the remaining battery indicator

switch, the remaining battery indicator lamp lights

and the battery remaining power can be checked.

(Fig.9) When releasing your finger from the

remaining battery indicator switch, the remaining

battery indicator lamp goes off. The table 5 shows

the state of remaining battery indicator lamp and

the battery remaining power.

As the remaining battery indicator shows somewhat

differently depending on ambient temperature and

battery characteristics, read it as a reference.

Handle

Switch

State of lamp Battery Remaining Power

The battery remaining power

is enough.

The battery remaining power

is a half.

The battery remaining power

is nearly empty.

Re-charge the battery soonest

possible.

Table 5

Remaining

battery

indicator

lamp

Remaining

battery

indicator

switch

Light switch

01Eng_WR18DSHL_US.p65 8/28/13, 14:4914

English

CAUTION

Do not touch the hammer case, as it gets very hot

during continuous work.

2. Work at a tightening torque suitable for the bolt

under impact

The optimum tightening torque for nuts or bolts

differs with material and size of the nuts or bolts.

An excessively large tightening torque for a small

bolt may stretch or break the bolt. The tightening

torque increases in proportion to the operaton time.

Use the correct operating time for the bolt.

3. Holding the tool

Hold the impact wrench firmly with both hands. In

this case hold the wrench in line with the bolt.

It is not necessary to push the wrench very hard.

Hold the wrench with a force just sufficient to

counteract the impact force.

4. Confirm the tightening torque

The following factors contribute to a reduction of

the tightening torque. So confirm the actual

tightening torque needed by screwing up some bolts

before the job with a hand torque wrench. Factors

affecting the tightening torque are as follows.

(1) Voltage

When the discharge margin is reached, voltage

decreases and tightening torque is lowered.

(2) Operating time

The tightening torque increases when the operating

time increases. But the tightening torque does not

increase above a certain value even if the tool is

driven for a long time.

(3) Diameter of bolt

The tightening torque differs with the diameter of

the bolt. Generally a larger diameter bolt requires

larger tightening torque.

(4) Tightening conditions

The tightening torque differs according to the torque

ratio; class, and length of bolts even when bolts with

the same size threads are used. The tightening

torque also differs according to the condition of the

surface of workpiece through which the bolts are to

be tightened. When the bolt and nut turn together,

torque is greatly reduced.

(5) Using optional parts

The tightening torque is reduced a little when an

extension bar, universal joint or a long socket is used.

(6) Clearance of the socket

A worn or deformed hex. or a square-holed socket

will not give an adequate tightness to the fitting

between the nut or anvil, consequently resulting in

loss of tightening torque.

Using an improper socket which does not match to

the bolt will result in an insufficient tightening

torque.

(7) Tightening torque varies, depending on the battery’s

charge level.

01Eng_WR18DSHL_US.p65 8/28/13, 14:4915

English

MAINTENANCE AND INSPECTION

CAUTION

Pull out battery before doing any inspection or

maintenance.

1. Checking the condition of the socket

A worn or deformed hex. or a square-holed socket

will not give an adequate tightness to the fitting

between the nut or anvil, consequently resulting in

loss of tightening torque. Pay attention to wear of a

socket holes periodically, and replace with a new

one if needed.

2. Check the Screws

Loose screws are dangerous. Regularly inspect them

and make sure they are tight.

CAUTION

Using this power tool with loosened screws is

extremely dangerous.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the

power tool.

Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

4. Inspecting the carbon brushes (Fig. 11)

The motor employs carbon brushes which are

consumable parts. Since and excessively worn

carbon brush can result in motor trouble, replace

the carbon brush with new ones when it becomes

worn to or near the “wear limit”. In addition, always

keep carbon brushes clean and ensure that they slide

freely within the brush holders.

NOTE:

When replacing the carbon brush with a new one,

be sure to use the Hitachi Carbon Brush Code No.

999100.

Fig. 11

Fig. 12

5. Replacing carbon brushes

Take out the carbon brush by first removing the

brush cap and then hooking the protrusion of the

carbon brush with a flat head screw driver, etc., as

shown in Fig. 13.

When installing the carbon brush, choose the

direction so that the nail of the carbon brush agrees

with the contact portion outside the brush tube. Then

push it in with a finger as illustrated in Fig. 14. Lastly,

install the brush cap.

CAUTION

䢇

Be absolutely sure to insert the nail of the carbon

brush into the contact portion outside the brush

tube. (You can insert whichever one of the two

nails provided.)

䢇

Caution must be exercised since any error in this

operation can result in the deformed nail of the

carbon brush and may cause motor trouble at an

early stage.

Fig. 13

Fig. 14

Wear limit

0.12" (3mm)

0.375"

(9.5mm)

Nail of carbon brush

Protrusion

of carbon

brush

Brush cap

Contact portion

outside brush tube

01Eng_WR18DSHL_US.p65 8/28/13, 14:4916

English

6. Check for Dust

Dust may be removed with a soft cloth or a cloth

dampened with soapy water.

Do not use bleach, chlorine, gasoline or thinner, for

they may damage the plastics.

7. Disposal of the exhausted battery

WARNING:

Do not dispose of the exhausted battery. The

battery must explode if it is incinerated. The

product that you have purchased contains a

rechargeable battery. The battery is recyclable. At

the end of it’s useful life, under various state and

local laws, it may be illegal to dispose of this

battery into the municipal waste stream. Check

with your local solid waste officials for details in

your area for recycling options or proper disposal.

8. Storage

Storing in a place below 104°F (40°C) and out of the

reach of children.

NOTE:

Make sure that the battery is fully charged when

stored for a long period (3 months or more). The

battery with smaller capacity may not be able to be

charged when used, if stored for a long period.

NOTE:

Storing lithium-ion batteries

Make sure the lithium-ion batteries have been fully

charged before storing them.

Prolonged storage of batteries with a low charge

may result in performance deterioration,

significantly reducing battery usage time or

rendering the batteries incapable of holding a

charge.

However, significantly reduced battery usage time

may be recovered by repeatedly charging and using

the batteries two to five times.

If the battery usage time is extremely short despite

repeated charging and use, consider the batteries

dead and purchase new batteries.

9. Service and repairs

All quality power tools will eventually require

servicing or replacement of parts because of wear

from normal use. To assure that only authorized

replacement parts will be used, all service and

repairs must be performed by a HITACHI

AUTHORIZED SERVICE CENTER, ONLY.

10. Service parts list

A: Item No.

B: Code No.

C: No. Used

D: Remarks

CAUTION

Repair, modification and inspection of Hitachi

Power Tools must be carried out by a Hitachi

Authorized Service Center.

This Parts List will be helpful if presented with the

tool to the Hitachi Authorized Service Center when

requesting repair or other maintenance. In the

operation and maintenance of power tools, the

safety regulations and standards prescribed in

each country must be observed.

MODIFICATIONS:

Hitachi Power Tools are constantly being improved and

modified to incorporate the latest technological

advancements.

Accordingly, some parts may be changed without prior

notice.

Important notice on the batteries for the Hitachi

cordless power tools

Please always use one of our designated genuine

batteries. We cannot guarantee the safety and

performance of our cordless power tool when

used with batteries other than these designated

by us, or when the battery is disassembled and

modified (such as disassembly and replacement

of cells or other internal parts).

01Eng_WR18DSHL_US.p65 8/28/13, 14:4917

English

ACCESSORIES

WARNING:

ALWAYS use Only authorized HITACHI replacement

parts and accessories. NEVER use replacement

parts or accessories which are not intended for use

with this tool. Contact HITACHI if you are not sure

whether it is safe to use a particular replacement

part or accessory with your tool.

The use of any other attachment or accessory can

be dangerous and could cause injury or mechanical

damage.

NOTE:

Accessories are subject to change without any

obligation on the part of the HITACHI.

STANDARD ACCESSORIES

Battery Charger

(UC18YRSL or UC18YFSL) ........... 1

Battery (BSL1830 or BSL1840) ..... 2

Battery cover ................................. 1

Plastic Case (Code No. 333810) ... 1

Without battery charger, battery,

battery cover and plastic case

OPTIONAL ACCESSORIES.....sold

separately

WR18DSHL

(2LSRK)

WR18DSHL

(NN)

1. Battery

BSL1830 (Code No. 330067)

BSL1840 (Code No. 335180)

2. Sockets

21.5

32.5

Code No.

873540

873536

873624

873626

873627

873628

873629

873630

985195

985196

Code No.

955138

955139

955140

955141

955142

955143

955144

955145

955146

955147

955148

985197

Socket

Ordinary Socket Long Socket

Designation

Dimension (mm) Dimension (mm)

Hex. Socket

Table 6 B = 1/2” (12.7 mm)

01Eng_WR18DSHL_US.p65 8/28/13, 14:4918

English

3. Extension bar:

The extension bar is convenient for working in very

restricted spaces or when the socket provided cannot

reach the bolt to be tightened.

CAUTION

When the extension bar is used, the tightening

torque is reduced slightly compared with the

ordinary socket.

4. Universal joint:

The universal joint is convenient for impacting nuts

when there is an angle between the socket and

wrench, or when working in a very narrow space.

Code No. Dimention B, S

873633 1/2" (12.7 mm)

Code No. Dimention B, S

992610 1/2" (12.7 mm)

01Eng_WR18DSHL_US.p65 8/28/13, 14:4919

Français

CONSIGNES DE SÉCURITÉ IMPORTANTES

Lire et comprendre toutes les précautions de sécurité, les avertissements et les instructions de fonctionnement

dans ce mode d’emploi avant d’utiliser ou d’entretenir cet outil motorisé.

La plupart des accidents causés lors de l’utilisation ou de l’entretien de l’outil motorisé proviennent d’un non

respect des règles ou précautions de base de sécurité. Un accident peut la plupart du temps être évité si l’on

reconnaît une situation de danger potentiel avant qu’elle ne se produise, et en observant les procédures de sécurité

appropriées.

Les précautions de base de sécurité sont mises en évidence dans la section “SECURITE” de ce mode d’emploi et

dans les sections qui contiennent les instructions de fonctionnement et d’entretien.

Les dangers qui doivent être évités pour prévenir des blessures corporelles ou un endommagement de la machine

sont identifiés par AVERTISSEMENTS sur l’outil motorisé et dans ce mode d’emploi.

NE JAMAIS utiliser cet outil motorisé d’une manière qui n’est pas spécifiquement recommandée par HITACHI.

SIGNIFICATION DES MOTS D’AVERTISSEMENT

AVERTISSEMENT indique des situations potentiellement dangereuses qui, si elles sont ignorées, pourraient

entraîner la mort ou de sérieuses blessures.

PRECAUTION indique des situations dangereuses potentilles qui, si elles ne sont pas évitées, peuvent entraîner

de mineures et légères blessures ou endommager la machine.

REMARQUE met en relief des informations essentielles.

SECURITE

AVERTISSEMENTS DE SÉCURITÉ GÉNÉRAUX CONCERNANT LES OUTILS ÉLECTRIQUES

AVERTISSEMENT:

Lire tous les avertissements de sécurité et toutes les instructions

Tout manquement à observer ces avertissements et instructions peut engendrer des chocs électriques, des

incendies et/ou des blessures graves.

Conservez tous les avertissements et toutes les instructions pour vous y référer ultérieurement.

Le terme "outil électrique", utilisé dans les avertissements, se réfère aux outils électriques (câblé) ou aux

outils à piles (sans fil).

1) Sécurité de l’aire de travail

a) Maintenir l'aire de travail propre et bien

éclairée.

Les endroits encombrés ou sombres sont

propices aux accidents.

b) Ne pas utiliser d'outils électriques en présence

de liquides, gaz ou poussière inflammables,

au risque de provoquer une explosion.

Les outils électriques créent des étincelles

susceptibles d'enflammer la poussière.

c) Ne pas laisser les enfants et les visiteurs

s'approcher de vous lorsque vous utiliser un

outil électrique.

Les distractions peuvent faire perdre le contrôle.

2) Sécurité électrique

a) Les prises de l'outil électrique doivent

correspondre à la prise secteur.

Ne jamais modifier la prise.

Ne pas utiliser d'adaptateurs avec les outils

électriques mis à la masse.

Les prises non modifiées et les prises secteurs

correspondantes réduisent les risques de

choc électrique.

b) Eviter tout contact avec les surfaces mises à

la masse telles que les tuyaux, radiateurs,

bandes et réfrigérateurs.

Le risque de choc électrique est accru en cas

de mise à la masse du corps.

c) Ne pas exposer les outils électriques à la pluie

ou à des conditions humides.

Si l'eau pénètre dans l'outil, cela augmente

les risques de choc électrique.

d) Ne pas utiliser le cordon à tort. Ne jamais

utiliser le cordon pour transporter ou

débrancher l'outil électrique.

Maintenir le cordon loin de la chaleur, de

l'huile, des bords pointus ou des pièces

mobiles.

Les cordons endommagés ou usés

augmentent les risques de choc électrique.

02Fre_WR18DSHL_US.p65 8/28/13, 14:5120

La page charge ...

Hitachi WR 18DSHL Safety Instructions And Instruction Manual

Marque: Hitachi

Modèle: WR 18DSHL

Catégorie: Outils électroportatifs

Taper: Safety Instructions And Instruction Manual

Télécharger le PDF

rapport

dans d''autres langues

English: Hitachi WR 18DSHL
español: Hitachi WR 18DSHL

Hitachi WR 18DSHL Safety Instructions And Instruction Manual

Hitachi WR 18DSHL Safety Instructions And Instruction Manual

dans d''autres langues

Documents connexes

Autres documents